physical properties - ace glass · 2017-10-06 · 7 order 1-800-223-4524 ˜ aceglass.com 8866...
Post on 20-Apr-2020
2 Views
Preview:
TRANSCRIPT
2
For Engineering Support, e-mail us at : design@aceglass.com
Physical PropertiesType Glass: Borosilicate
Working Pressure*: ½" – ¾" – 1" ..............100 p.s.i. 1½" – 2" – 3" ...............75 p.s.i. 4" .................................50 p.s.i. 6" .................................30 p.s.i. @ Room Temperature
Test Pressure*: 11⁄2 Times Working Pressure
Operating Temp. (Maximum): Freezing point to 450°C Normal use — 230°C
Glass Therm. Expansion: 32 x 10-7/°C
Glass Therm. Conductivity: 0.73 BTU/hr. ft.2/F°/ft. at 212°F
Glass Therm. Shock Diff.: 160°C
Making Joints with Process Pipe Couplings
Chemical PropertiesDurability Acids: All except Hydrofluoric or Phosphoric with Fluorides
Durability Alkalies: Some attack above 120°F and above pH11
Coupling Outer Band: One bolt stainless steel ½"–6"
Coupling Compression Liner/Seal Ring: Hydrin /TFE Seal Max. Temp. 200°C; Buna-N/TFE Max. Temp. 250°C
* Note: Gas pressure recommendations: It is recommended that suitable safeguards for equipment and personnel be provided in the unlikely event of system failure when glass pipe is used under a gas pressure. This safeguard is recommended due to the potential energy of gases under pressure or vacuum.
1. Dip coupling in water or wipe beaded ends with damp cloth.
2. Snap coupling over one end of pipe making certain TFE liner is behind bead...then stab other section of pipe into opposite side of coupling.
3. Tighten coupling bolt with 6" rachet wrench until the gap between segments is approximately 3∕16".
1 2 3
Ace Glass has been manufacturing and fabricating glassware and equipment for the scientific and research communities for over seventy years. Ace fabricates glass process pipe here in the USA, from medium- and heavy-wall borosilicate tubing such as Scimax and Duran®, to provide you with a high quality product to fit into your process stream. From glass process pipe to glass reactors and pilot plants, to temperature equipment and sensors, Ace offers a broad line of products to the process engineer. Ace will also fabricate custom sizes and shapes for your needs — if you don’t see what you need in this brochure, contacts us at www.aceglass.com or 800-223-4524 to discuss your needs with our engineering staff.
3
Ordering & Product Information: 1-800-223-4524 ◾ aceglass.com
8830 SWEEP ELBOW
8828 BEADED PIPE All pipe is available from stock in lengths shown; special lengths available on special order. Length tolerance ±1/8".
A B A B A B A B ½" I.D. 57∕64" ¾" ¾" I.D. 15∕32" 1" 1" I.D. 117∕32" 15∕16" 1½" I.D. 21∕16" 127∕32"
Length Order Code Length Order Code Length Order Code Length Order Code
3" 8828-02 3" 8828-102 3" 8828-202 — — 4" 8828-03 4" 8828-103 4" 8828-203 4" 8828-303 6" 8828-05 6" 8828-105 6" 8828-205 6" 8828-305 12" 8828-09 12" 8828-109 12" 8828-209 12" 8828-309 18" 8828-11 18" 8828-111 18" 8828-211 18" 8828-311 24" 8828-13 24" 8828-113 24" 8828-213 24" 8828-313 30" 8828-15 30" 8828-115 30" 8828-215 30" 8828-315 36" 8828-20 36" 8828-120 36" 8828-220 36" 8828-320 48" 8828-25 48" 8828-125 48" 8828-225 48" 8828-325 60" 8828-30 60" 8828-130 60" 8828-230 60" 8828-330 72" 8828-38 72" 8828-138 72" 8828-238 72" 8828-338 84" 8828-45 84" 8828-145 84" 8828-245 84" 8828-345 96" 8828-56 96" 8828-156 96" 8828-256 96" 8828-356 108" 8828-260 108" 8828-360 120" 8828-262 120" 8828-362
A B A B A B A B 2" I.D. 29∕16" 25∕16" 3" I.D. 311∕16" 37∕16" 4" I.D. 47∕8" 49∕16" 6" I.D. 71∕8" 65∕8"
Length Order Code Length Order Code Length Order Code Length Order Code 4" 8828-403 4" 8828-503 — — — — 6" 8828-405 6" 8828-505 6" 8828-605 6" 8828-705 12" 8828-409 12" 8828-509 12" 8828-609 12" 8828-709 18" 8828-411 18" 8828-511 18" 8828-611 18" 8828-711 24" 8828-413 24" 8828-513 24" 8828-613 24" 8828-713 30" 8828-415 30" 8828-515 30" 8828-615 30" 8828-715 36" 8828-420 36" 8828-520 36" 8828-620 36" 8828-720 48" 8828-425 48" 8828-525 48" 8828-625 48" 8828-725 60" 8828-430 60" 8828-530 60" 8828-630 60" 8828-730 72" 8828-438 72" 8828-538 72" 8828-638 72" 8828-738 84" 8828-445 84" 8828-545 84" 8828-645 84" 8828-745 96" 8828-456 96" 8828-556 96" 8828-656 96" 8828-756 108" 8828-460 108" 8828-560 108" 8828-660 108" 8828-760 120" 8828-462 120" 8828-562 120" 8828-662 120" 8828-762
90° 45° 60° 22½°
Size A" Order Code Size A" Order Code Size A" Order Code Size A" Order Code
½" –90° 2¼ -03 ½" – 45° 2¼ -103 ½" – 60° 2¼ -203 ½" – 22° 2¼ -303 ¾" – 90° 2½ -05 ¾" – 45° 2½ -105 ¾" – 60° 2½ -205 ¾" – 22° 2½ -305 1" – 90° 2¾ -07 1" – 45° 2¾ -107 1" – 60° 2¾ -207 1" – 22° 2¾ -307 1½"– 90° 5 -09 1½"– 45° 3½ -109 1½"– 60° 3½ -209 1½"– 22° 3½ -309 2" – 90° 6 -11 2" – 45° 4 -111 2" – 60° 4 -211 2" – 22° 4 -311 3" – 90° 7 -13 3" – 45° 5 -113 3" – 60° 5 -213 3" – 22° 5 -313 4" – 90° 10 -15 4" – 45° 7 -115 4" – 60° 7 -215 4" – 22° 7 -315 6" – 90° 12 -17 6" – 45° 9 -117 6" – 60° 9 -217 6" – 22° 9 -317
Use catalog dimensions for piping layout as gasket thickness allowance is included.
4
For Engineering Support, e-mail us at : design@aceglass.com
8833 90° SHORT RADIUS ELBOW
8836 STRAIGHT T
8831 REDUCER ELBOW
8832 90° MITERED ELBOW
8832
Order Size A" Code
1½"–90° 3 ½ 8832-03 2" –90° 4 8832-05 3" –90° 5 8832-07 4" –90° 7 8832-09 6" –90° 9 8832-11
8833
Order Size A" Code
1½"–90° 3½ 8833-32 2" –90° 4 8833-34 3" –90° 5 8833-36 4" –90° 7 8833-38
Interchangeable with 8836 – TEE
Order Size A" B" Code
¾" x ½" 2½ 2½ 8831-02 1" x ½" 2¾ 2¾ 8831-04 1" x ¾" 2¾ 2¾ 8831-06 1½" x ½" 3½ 3 8831-08 1½" x ¾" 3½ 3 8831-10 1½" x 1" 3½ 3 8831-12 2" x ½" 4 3 8831-14 2" x ¾" 4 3 8831-16 2" x 1" 4 3 8831-18 2" x 1½" 4 3½ 8831-20
Order Size A" B" Code
3" x 1" 5 3½ 8831-22 3" x 1½" 5 4 8831-24 3" x 2" 5 4½ 8831-26 4" x 1" 7 4 8831-28 4" x 1½" 7 4½ 8831-30 4" x 2" 7 5 8831-32 4" x 3" 7 5½ 8831-34 6" x 1½" 9 5½ 8831-36 6" x 2" 9 6 8831-38 6" x 3" 9 6½ 8831-40 6" x 4" 9 8 8831-42
Order Size A" B" Code
½" 4½ 2¼ 8836-02 ¾" 5 2½ 8836-04 1" 5½ 2¾ 8836-06 1½" 7 3½ 8836-08 2" 8 4 8836-10 3" 10 5 8836-12 4" 14 7 8836-14 6" 18 9 8836-16
5
Ordering & Product Information: 1-800-223-4524 ◾ aceglass.com
Order Size A" Code
½" 2 8845-03 ¾" 2 8845-05 1" 2 8845-07 1½" 3 8845-09 2" 4 8845-11 3" 4¾ 8845-15 4" 6 8845-17 6" 7 8845-19
Size Order Run x Branch A" B" C" Code
¾" x ½" 5 2½ 2½ 8837-03 1" x ½" 5½ 2¾ 2¾ 8837-05 1" x ¾" 5½ 2¾ 2¾ 8837-07 1½" x ½" 7 3 3½ 8837-09 1½" x ¾" 7 3 3½ 8837-11 1½" x 1" 7 3 3½ 8837-13 2" x ½" 8 3 4 8837-15 2" x ¾" 8 3 4 8837-17 2" x 1" 8 3 4 8837-19 2" x 1½" 8 3½ 4 8837-21
8845 END CAP
Order Size A" Code
¾" x ½" 4 8842-03 1" x ½" 4 8842-05 1" x ¾" 4 8842-07 1½" x ½" 4 8842-09 1½" x ¾" 4 8842-11 1½" x 1" 4 8842-13 2" x ½" 4 8842-15 2" x ¾" 4 8842-17 2" x 1" 4 8842-19 2" x 1½" 4 8842-21 3" x 1" 5 8842-23
8842 REDUCER
8849 U BEND
8837 REDUCING T
Size Order Run x Branch A" B" C" Code
3" x 1" 10 3½ 5 8837-23 3" x 1½" 10 4 5 8837-25 3" x 2" 10 4½ 5 8837-27 4" x 1" 14 4 7 8837-29 4" x 1½" 14 4½ 7 8837-31 4" x 2" 14 5 7 8837-33 4" x 3" 14 5½ 7 8837-35 6" x 1½" 18 5½ 9 8837-37 6" x 2" 18 6 9 8837-39 6" x 3" 18 6½ 9 8837-41 6" x 4" 18 8 9 8837-43
Order Size A" Code
3" x 1½" 5 8842-25 3" x 2" 5 8842-27 4" x 1" 7 8842-29 4" x 1½" 7 8842-31 4" x 2" 7 8842-33 4" x 3" 7 8842-35 6" x 1" 9 8842-37 6" x 1½" 9 8842-39 6" x 2" 9 8842-41 6" x 3" 9 8842-43 6" x 4" 9 8842-45
Order Size A" Code
½" 2¼ 8849-03 ¾" 2½ 8849-05 1" 5½ 8849-07 1½" 7 8849-09 2" 7 8849-11 3" 9 8849-13 4" 12 8849-15
6
For Engineering Support, e-mail us at : design@aceglass.com
High Temperature – Buna-N Liner/PTFE
Max Torque, Order Size A" B" C" D" in-lbs Code
½" 15∕8 13∕8 7∕8 3∕16 20 8856-03 ¾" 1¾ 1½ 7∕8 3∕16 25 8856-05 1" 25∕8 17∕8 1 3∕16 35 8856-07 1½" 3 25∕8 15∕16 3∕16 50 8856-09 2" 3½ 31∕8 15∕16 3∕16 60 8856-11 3" 4¾ 4¼ 17∕16 3∕16 75 8856-13 4" 6 5½ 1½ 3∕16 80 8856-15 6" 8¾ 8 1¾ ¼ 90 8856-17
All hangers are zinc coated and have factory-applied plastic sleeve to prevent glass-to-metal contact. Use one hanger every 8 or 10 feet. Support all valves and meters individually.
Coupling assemblies consist of a .300 series stainless steel outer band with T-Bolt and hex nut, black Buna-N liner and a TFE seal ring.
No. 8856 coupling is designed for temperature service up to 450°F.
8847 END PLUG
Order Size Code
1" (25mm) 8862-03 2" (50mm) 8862-07 3" (76mm) 8862-11
Order Size A" Code
1½" 7∕8 8847-02 2" 1 8847-04 3" 11∕8 8847-06 4" 1¼ 8847-08 6" 1½ 8847-10
8862 PADDED PIPE HANGER with Mounting Foot
8863 PADDED PIPE HANGER without Foot
8856 PROCESS PIPE COUPLINGS Bead to Bead
A
D
B
C
A
D
B
C
Use catalog dimensions for piping layout as gasket thickness allowance is included.
Order Size Code
½" 8863-02 ¾" 8863-04 1" 8863-06 1½" 8863-08 2" 8863-10 3" 8863-12 4" 8863-14 6" 8863-16
7
Ordering & Product Information: 1-800-223-4524 ◾ aceglass.com
8866 COUPLING ASSEMBLY* Beaded to Conical End Pipe
To join beaded end pipe to conical end pipe. Kit includes two flanges, inserts, bolts and TFE sheath gasket.
* Pressure rating limited to that of Conical Pipe Stem. Not to be used with Beaded Armored Pipe.
Size NPT A" Order Code
½" 29∕16 8870-02 ¾" 29∕16 8870-04 1" 29∕16 8870-06
8868 Bolts & NutsFor All Coupling Kits & Assemblies
Order Description Qty. Code
5∕16"–18 x 2¼" 4 8868-03 5∕16"–18 x 2½" 4 8868-04 5∕16"–18 x 3" 8 8868-05 3∕8" –16 x 3" 8 8868-06 ½" –13 x 2" 4 8868-07 ½" –13 x 2¼" 4 8868-08 ½" –13 x 2½" 4 8868-09 5∕8" –11 x 2½" 4 8868-10 5∕8" –11 x 3" 4 8868-11 5∕8" –11 x 3½" 4 8868-12 ¾" –10 x 3½" 4 8868-13
Inserts for 8866 (one each)
Size Order Code
1" 8867-76 8867-77 1½" 8867-78 8867-79 2" 8867-80 8867-81 3" 8867-82 8867-83 4" 8867-84 8867-85 6" 8867-86 8867-87
Size Order Code
1" 8866-03 1½" 8866-05 2" 8866-07 3" 8866-09 4" 8866-11 6" 8866-13
Gasket for 8868T.F.E. Machined (Full Flow) Gasket
Description Size Order Code
" 1½" 8868-17 " 2" 8868-18 " 3" 8868-19 " 4" 8868-20 " 6" 8868-21
Flange for 8866 (Need 2)
Size Order Code Size Order Code
1" 8867-68 4" 8867-72 1½" 8867-69 4" 8867-73 2" 8867-70 6" 8867-74 3" 8867-71 6" 8867-75
8869 FAUCET UNION — ALUMINUM Beaded to ½" Metal IPS Straight Pipe ThreadReplacement parts for No. 8869 assembly include code -07 gasket and code -09 cushion ring.
Size A" B" Order Code
½" Assembly 1¾ 1¼ 8869-03 ½" Gasket (TFE) — — 8869-07 ½" Cushion (TFE) — — 8869-09
8870 MALE THREADED ADAPTER 316 Stainless SteelUsed to join threaded female fittings, valves and flanges to beaded pipe. Size refers to bead and thread.
A
8867/8868 COUPLING KIT COMPONENTS
Assembly Consists of...
Size Flange Insert Gasket 7190 Nuts & Bolts — Qty.
1" 8867-68 8867-76 8868-16 3∕8 –16 x 2¼ 4 8867-77 1½" 8867-69 8867-78 8868-17 3∕8 –16 x 2¼ 4 8867-79 2" 8867-70 8867-80 8868-18 3∕8 –16 x 2½ 4 8867-81 3" 8867-71 8867-82 8868-19 3∕8 –16 x 3 4 8867-83 4" 8867-72 8867-84 8868-20 3∕8 –16 x 3 8 8867-73 8867-85 6" 8867-74 8867-86 8868-21 3∕8 –16 x 3 8 8867-75 8867-87
Size A" Order Code
11⁄2" 29∕16 8870-08 2" 25∕8 8870-10 3" 31∕8 8870-12
Visit us on the Web:
www.aceglass.com
Additional literature available…
Request your copy by phone, mail or on the Web.
P.O. Box 688 • Vineland, NJ 08362-0688 • 856-692-3333 • Fax: 856-692-8919
TOLL-FREE: 1-800-223-4524 • FAX: 1-800-543-6752
www.aceglass.com email: sales@aceglass.com
Easy online ordering ◾ Private ◾ Safe ◾ Secure
0114
top related