proposed outpatient department block at rift valley ... · f excavate for foundation strip footing...
Post on 25-Mar-2020
3 Views
Preview:
TRANSCRIPT
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
GROUND FLOOR
ELEMENT NO. 1
SUBSTRUCTURES
(All provisional)
A Clear site of all grass and small trees not
exceeding 600mm girth and cart away or burn
arisings 6200 Sm
B
Cut down trees exceeding girth over 600mm
girth grub up roots and stumps chop to required
lengths and hand over to client/cart away 50 No
C Excavate oversite to remove vegetable top soil
average 250mm deep and cartaway to spoil heaps
as directed on site 6200 Sm
D Excavate to reduce level not exceeding 1.5m
deep from stripped level and cart away 9225 Cm
E Ditto 150 to 3.00mm deep ditto 9225 cm
F Excavate for foundation strip footing in normal
soil not exceeding 1.5m deep from reduced level
2112 Cm
G Ditto; but for column bases 5011 Cm
H Excavate for strip footing 1.50 to 3.0metres deep464 Cm
J Ditto; but for column bases 1743 Cm
K Return fill and ram selected excavated material
around foundations 5538 Cm
L Load, wheel and cart away from site surplus
excavated material and deposit in approved
dumping area 1738 Cm
M Extra over all kinds of excavation for excavating
in soft rock 1200 Cm
N Ditto; in hard rock 800 Cm
Total to collection
92
PROPOSED OUTPATIENT DEPARTMENT BLOCK AT RIFT
VALLEY PROVINCIAL GENERAL HOSPITAL NAKURU
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A Allow for keeping excavations free from all
water by pumping or otherwise Item
B Ditto; for plunking and strutting to sides of
excavations Item
C 300mm Thick (average) approved broken quarry
stone hardcore filling in two equal layers well
rolled and compacted 3920 Sm
D Form sinking size 500mm (average)wide x
300mm deep in hardcore including forming
splayed sides 42 Lm
E Well compacted imported granular material fill
to make up levels 3920 Cm
F 50mm thick stone dust blinding to surface of
hardcore 3920 Sm
Concrete works
50mm plain concrete mix (1:3:6 - class
15/20mm) blinding under:
G Strip footing 1602 Sm
H Column bases 2311 Sm
J Shaft Base 0 Sm
Vibrated Reinforced Contrete mix (1: 1 1/2 :3)
class 25/20mm in:
K Strip footing 401 Cm
L Column bases 1333 Cm
M Wall base 116 Cm
N Column 54 Cm
Carried to collection
93
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 150mm thick floor bed 3920 Sm
B 200mm thick Wall 365 Sm
C Steel fabric mesh reinforcement type A142
weighing 2.22kg to BS 4483 with 150mm side
laps (measured ne -no allowance for laps) 3920 Sm
D Extra for 500mm (average) thicknessing under
beds 300mm deep 42 Lm
Expansion joint
E 25mm thick Aeroflex filler 291 Sm
F 25 x 25mm "Expendite" sealer 194 Lm
Sawn formwork to:
G Sides of strip footing 1181 Sm
H Sides of columns bases 2254 Sm
F Sides of column 303 Sm
K Sides of columns curved to 225mm radii 43 Sm
L Ditto curved to 200mm radii 113 Sm
M Ditto curved to 125mm radii 66 Sm
N Sides of wall surfaces 730 Sm
P Sides of wall bases 150 Sm
Q Edges of ground floor bed exceeding 75mm but
not exceeding 150mm wide 722 Lm
Total to collection
94
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A Ditto curved to 5500mm radii 36 Lm
MASONRY
B 200mm thick natural stone walling; quarry
dressed bedded and jointed in cement sand(1:3)
motor; reinforced with hoop iron at alternate
courses 2953 Sm
D 400mm thick wall 310 Sm
E 200mm thick skin wall 0 Sm
Surfaces Treatement
F "Dragnet" or other equal and approved
antitermite insectcide treatment to blinded
hardcore surfaces applied in accordance with
manufacturer's instructions 3920 Sm
G 1000 gauge polythene sheeting laid under
concrete floor bed 3920 Sm
Reinforcement
Ribbed 'D' bars as described in
H 16mm diameter bars in column bases 96087 Kgs
J 20mm Ditto in bases 35760 Kgs
K 16mm Ditto in columns 0 Kgs
L 20mm ditto in columns 16500 Kgs
M 12mm Ditto; in columns 1805 Kgs
N 8mm ditto 1647 Kgs
P 10mm Ditto in strip footing 18121 Kgs
Q 12mm ditto 3090 Kgs
Total carried to collection
95
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 8mm ditto 4098 Kgs
B 16mm ditto in shaft base 14008 Kgs
C 12mm in wall and wall base 18768 Kgs
D 16mm ditto 35020 Kgs
Cement and sand (1:4) paving
E 25mm thick screed 365 Sm
F 12mm thick to plinth surfaces wood floated 303 Sm
G Prepare and apply three coats of bitumastic paint
to rendered surfaces 303 Sm
Tanking and water proofing
H Vandex super 1.5Kg per square metre applied as
per manufacturer's printed instructions 510 Sm
J 200mm thick PVC water bar embedded in
concrete between floor and wall joints 170 Lm
K 30 x 30mm integral angle fillets at junction of
wall and floor 170 Lm
L 300mm reglet band at floor and wall junction 170 Lm
Cement sand (1:4) screed backing:
M 20mm screed backing to receive water proofing
treatment 510 Sm
Carried to collection
Collection
Brought forward from Page 92
Brought forward from Page 93
Brought forward from Page 94
Brought forward from Page 95
Brought forward from Page 96 Above
Total element 01 to summary
96
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 02
REINFORCED CONCRETE
Superstructures
Vibrated reinforced concrete (1:1 1/2:3) Class
25/20mm in:
A Beams 245 Cm
B Gutter beam 150mm thick 64 Cm
C Columns 78 Cm
D Suspended slabs, thickness 175mm 2273 Sm
E 175x200mm thick kerb 484 Lm
Reinforcement (all provisional)
Deformed bars BS 4461 as described in:
F 8mm diameter bars in beams 9560 Kgs
G 16mm ditto in beams 11201 Kgs
H 20mm ditto in beams 8849 Kgs
J 8mm dittto; in column 2660 Kgs
K 12mm ditto 2166 Kgs
L 16mm ditto in column 0 Kgs
M 20mm ditto; 19800 Kgs
N 8mm ditto in gutter beam 3240 Kgs
P 10mm ditto 6055 Kgs
Q 16mm ditto 3240 Kgs
R 20mm ditto 1560 Kgs
A 10mm in suspended floor slab 60650 Kgs
B 12mm ditto in Kerb 2033 Kgs
Carried to collection
97
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Sawn formwork to:
A Sides and soffits of beams 2613 Sm
B Ditto curved to 5500mm radii 51 Sm
C Ditto to 2500mm radii 23 Sm
D Sides and soffits of gutter beams 440 Sm
E Ditto to 5500 mm radii 62 Sm
F Sides of columns 512 Sm
G Ditto curved 225mm radii 72 Sm
H Ditto curved 200mm radii 277 Sm
J Sides of columns circular on plan to 125mm
radii 111 Sm
K Soffites of suspended slabs 2273 Sm
L Edges of ditto 150-225mm wide 584 Sm
M Sides and soffites of kerb 194 Sm
Total carried to collection
Collection
Brought forward from page 97
Brought forward from page 98
Total element 02 summary
98
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 03
WALLING
External walls
Hessian based Bituminous Damp Proof
Course bedded and jointed in cement sand
mortar 1:3
A 200mm wide 1002 Lm
B 150mm wide 0 Lm
C 100mm wide 43 Lm
D 400mm wide 206 Lm
D 200mm thick natural stone walling; medium
chiseled dressed; bedded and jointed in cement
and (1:3) mortar 825 Sm
E 200mm thick precast concrete louvre block
walling jointed and bedded in cement mortar
(1:4) 114 sm
Internal walls
Approved load bearing machine dressed
"Thika" natural stone walling bedded and
jointed in cement sand (1:3) mortar with
20mm wide hoop irons in every alternate
course
F 200mm thick walling 1224 Sm
G 150mm thick ditto 0 Sm
H 100mm thick 91 Sm
J 200mm thick dwarf wall 141 Sm
K 400mm thick wall 492 Sm
Aluminium partition walling
L Powder coated anodised aluminium curtain
walling comprising 100 x 50mm extruded
aluminium frame sections at 900mm vertical
centers and 1050mm horizontal centres; panell
infilled with and including 6mm clear sheet
glass; 2975mm high overall 6 Lm
Total element 03 walling to summary
99
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 03
DOORS
Mild steel casement
A Double grilled door comprising 50 x 50 x 3mm
rolled hollow section frame all round in filled
with 30 x 30 x 2mm thick RHS vertical baluster
150mm center and similar horizontal member at
200mm centers in a straggered configuration
overall size 1800 x 2550mm high 0 No
B Ditto single leaf size 900 x 25500mm high 0 No
C Mild steel pannel double door overall size
3000x2550mm high in 2No. equal leaves each
leaf comprising of 6 No size 300x800mm high
10mm thick glass panels including 1200x200mm
and 1200x300high double plate complete with
100x50x3mm RHS framing and metal lugs
including purpose made hanging and locking
accessories once primer before delivery to the
site. 2 No
D Ditto size 1800 x 2550mm high 8 No
E Ditto single leaf size 900x1500mm high 0 No
Total carried to collection
100
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Aluminium
A Aluminium sections 2mm thick 50 x 50mm
extrusions in top bottom and stiles and 100 x
50mm middle rail resulting bottom panel infilled
with 25mm thick blockboard laminate faced both
sides and top panel left open for glazing (m/s) in
door overall size 900 x 3050mm high comprising
900 x 950mm high top fanlight and 900 x
2100mm openable leaf complete with and
including locking devices 0 No
B Ditto double doors in 2No. Equal leaves overall
size 1800 x 3050mm high 0 No
Timber doors
C 50mm thick double paneled door overall size
1200 x 2400mm high all in solid mahogany in
two equal leaves each leaf comprising 150mm
top rail and stiles 200mm middle and bottom rail
resulting both panels instilled with bevel raised
and fielded panels 8 No
Total carried to collection
101
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
HDF Mahogany veneered timber door
A 45mm thick moulded panel door single swing as
supplied by BG Bison or other equal approved
overall size 900 x 2850mm high with 950mm top
fanlight 14 No
B 45mm ditto size 900x2400mm high with 300mm
fanlight ditto 0 No
C 45mm thick moulded panelled double door single
swing in two equal leaves overall size 1200 x
2550mm high comprising of 300 x mm high
glazed fan light at to (m/s) 1200 x 2100mm high
openable leaves each faced with interior quality
mahogany veneer both sides and hard wood
lipped all round 13 No
D 45mm thick moulded panel double door double
swing ditto
6 No.
Flush doors
E 45mm thick semi solid cored flush door in 2No.
Equal leaves hardwood lipped size 900 x
2850mm high faced both sides with interior
quality veneer facing both sides with 900 x 750
high glazed fanlight at top 6 No
F Size 900 x 2100mm ditto 6 No
G Ditto 1300 x 2100mm high double leaf 10 No
The following in wrot mahogany
H 200 x 50mm thick door frame with one labour
plugged 432 Lm
J 200 x 50mm transome, 2 labours 106 Lm
K 200x50mm mullion 29 Lm
L 150x50mm thick frame with one labour plugged 84 Lm
M 150x50mm transome, 2 labours 13 Lm
N 100 x 50mm frame one labours plugging 86 Lm
Total carried to collection
102
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 40 x 15mm architrave with one labour 602 Lm
B 25mm quadrant 602 Lm
C 25 x 25mm glazing beads 364 Lm
4mm thick clear sheet glass to wood:
D Panes 0.5 to 1.00 square meters 48 Sm
E Panes 0.1to 0.5 square metres 5 Sm
4mm thick clear sheet to metal with glazing
compound
F Panes 0.5 to 1.00 square metres 8 Sm
Ironmongery
Supply and fix the following ironmongery as
"union" or other equal and approved to wood
with matching screws
G Cylinder Bathroom lock set with turn handle and
rose in satin anodized aluminium set of lever
furniture Ref. Toucan DS-051 16 No
H Double cylinder lock set with handle on plate
complete with lever furniture ditto. Ref.
Elegance LS-C85-306 SN 14 No
J 5 lever Deadlock to steel door 0 No
K Rebated Double cylinder lock set for double door
with satin anodized aluminium set of lever
furniture Ref. Elegance LS-C85-306 SN 64 No
L 100mm stainless steel bearing butt hinges Ref.
BB-403030-SS 39 Prs
M 100mm brass parliament butt hinges Ref. P-
404040-SS 60 Prs
N Steel door lock 9 NO
Total carried to collection
103
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A Door closer as Union Ref. 8834 4 No
B 38mm diameter rubber door stopper plugged to
floor 270 No
C 150mm long lever action flush bolt Ref. No
U8052 134 No
Total carried to collection
Collection
Brought forward from page 100
Brought forward from page 101
Brought forward from page 102
Brought forward from page 103
Brought forward from page 104
Total element o3 carried to summary
104
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 04
WINDOWS
Fine chisseled "Blue Njiru" stone walling in
cement mortar
A 150 x 22mm cill, bedded and jointed in cement
and sand 1:1 and pointed in coloured cement
mortar 211 Lm
Supply and fix double metal curtain rods
from "Challenge Enginering" or other equal
and approved comprising of 25mm diameter
wrought iron front 16mm diameter rear rail
complete with fixing brackets, curtain holding
rings and decorative end stopsand all
necessary paintwork
B Curtain rods 200 Lm
Total to collection
105
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Casement - External
Supply, assemble and fix the following
purpose-made mild steel TOP HUNG
OUTWARD OPENABLE windows casement
complete with all opening accessories, 50 x
50mm thick frame units; including "snap on"
30mm wide permanent vent; building in ligs
to jambs; plugging and screwing head and
cill; bedding frames in waterproof cement
mortar and pointing in approved mastic
externally; fixing 6mm thick reflective glass
m.s oiling, easing and adjusting as described
in the following overall sizes
A 2100 x 1650mm high 69 No
B 2100 x 2000mm high 12 No
C 2100 x 750mm high 6 No
D 2400x750mm high 3 No
E 1800x1650mm high 2 No
F 900x1650mm high 2 NO
G 900x750mm high 1 No
Glazing
H 4mm thick Reflective sheet glass and glazing in
panes 0.1-1.0sm with putty compound 299 Sm
J Ditto; obscured glass 16 Sm
Total carried to collection
106
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Casement - Internal
Supply, assemble and fix the following
purpose-made mild steel Top Hung Outward
Opening windows casement complete with all
opening accessories, 50 x 50mm thick frame
units; including "snap on" 30mm wide
permanent vent; building in ligs to jambs;
plugging and screwing head and cill; bedding
frames in waterproof cement mortar and
pointing in approved mastic externally; fixing
6mm thick reflective glass m.s oiling, easing
and adjusting as described in the following
overall sizes
A 2100 x 1050mm high 6 No
B 1500 x 1050mm high 18 No
C 900x1500mm high 4 No.
Glazing
D 4mm thick reflective sheet glass and glazing in
panes 0.1-1.0sm with Putty compound 47 Sm
E Ditto; obscured glass 0 Sm
Total carried to collection
COLLECTION
Brought forward from page 105
Brought forward from page 106
Brought forward from page 107 above
Total element 04 windows to summary
107
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 05
EXTERNAL FINISHES
Wall Finishes
A Extra over natural stone walling for neat flush
horizontal and vertical joints in coloured cement
mortar 0 Sm
Cement and sand (1:4)
B 15mm thick cement sand (1:4) render to columns
354 Sm
C Ditto beam 235 Sm
D Ditto wall facade surfaces 784 Sm
E Ditto sides of gutter beam fascia 267 Sm
F Ditto sides and soffites of kerb 274 Sm
G Screeding to receive wall finish 824 SM
Cement lime plaster: 15mm thick (1:2:9)
H Plaster to soffites of gutter 258 Sm
Rough and Tough wall finish
J Prepare and apply rough and touch exterior wall
finish as "Crown paints" or equivalent and to
approved colour 1914 Sm
Hand scratched burnt clay
K 250x75x35mm thick brick facing in cement
mortar 421 SM
Mazerah cladding
L 200x200x20mm thick cladding fixed with
cement and sand (1:2) mortar 403 SM
Total to collection
108
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Roof finishes
A Form groove in concrete for edge of felt roofing
and grout in cement sand mortar (1:4) including
forming bell mouth joint 287 Lm
Supply and fit APP water proofing membrane
(m/s) as Italbuild Ltd laid strictly in
accordance with manufacturer's printed
instructions
B Gutter cover laid to fall and cross fall on sceed 158 Sm
C 725mm high with top edge dressed into groove
(m/s) and bottom edge jointed to felt 296 Lm
D Dress felt around 100mm rain water outlet 26 No
Light weight roof screeds consisting of
cement, sand and pumice (1:3:7) with 6mm
layer of cement and sand topping laid to falls
and crossfalls.
E 25mm screed on concrete to receive felt roofing
sloping < 45 degrees from horizontal 158 Sm
F 15mm ditto to sides of gutter beam 296 Sm
G 50 x 50mm triangular fillet 287 Lm
H Work screed around 100mm rainwater outlet 26 No
Precast concrete class 20/12mm fair faced
finished smooth
J 250x50mm capping sunk weathered both
surfaces ad twice throated bedded and jointed in
cement mortar (1:3) 305 Lm
Total carried to collection
109
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Curtain walling
A Curtain walling in mild steel comprising main
100x50x4mm thick extruded rolled hollow
section (RHS) frame section at 800mm vertical
general spacing and 700 horizontal centres
resulting panels infilled with 5mm thick
toughedned glass and glazing with putyy on
25mm 'T' sections 300mm wide and 600mm high
282 SM
Carried to collection
COLLECTION
Brought forward from page 108
Brought forward from page 109
Brought forward from page 110
Total element 05 carried to summary
110
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 06
INTERNAL FINISHES
FLOOR FINISHES
Cement and sand (1:4) screed
A Screed backing under floors finished with wood
float, thichness 32mm to receive ceramic tiles
(m/s) 141 Sm
B Ditto 20mm thick to floor to receive terrazzo
(m/s) 3756 Sm
Floor tiles
C 330 x 330 x 8mm thick ceramic tiles as
manufactured by "Flamingo Tiles" or other
approved non-slip tiles fixed with approved
adhesive in approved 141 Sm
D 100mm high ditto skirting 0 Lm
Polished white cement based terrazo
E 20mm thick paving to floor polished smooth
coomplete with and including 40x4mm thick
white plastic divindings strips 3756 Sm
F 20x100mm high skirting rounded top edge and
cored junction with floor 2083 Lm
Total to collection
111
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
WALL FINISHES
Cement and sand (1:4) screed
A Screed backing to wall wood floated thickness
15mm 469 Sm
Coloured glazed ceramic wall tiles and fittings
(cloakrooms)
B 200 x 300 x 6mm as manufactured by "Flamingo
Tiles" or other approved coloured tiles bedded
and jointed in cement and sand 1:1 and pointed
in coloured cement grouting 469 Sm
Cement Lime plaster; 15mm thick (1:2:9)
C Plaster to wall surfaces 4555 Sm
D Ditto concrete surface 784 Sm
E Ditto to soffits of suspended slabs 2273 Sm
CEILING FINISHES
F Suspended accoustic boards suspended to steel
truss complete with corner panel suspensions,
and flush jointing12mm thick 0 Sm
G 19mm gypsum ceiling lining to soffites in
approved pattern 1647 Sm
H Extra over for forming trap door size 600 x
600mm 10 No
J 100 x 25mm decorative gypsum cornice 2262 Lm
K 50x50mm Aluminium 'U' section channel fixed
to timber 3808 Lm
Total carried to collection
112
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
COLLECTION
Brought forward from page 111
Brought forward from page 112
Total element 06 internal finishes to summary
113
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO.7
ROOF CONSTRUCTION, COVERING AND
RAIN WATER DISPOSAL
Roof covering
A 1320x370mm stone coated steel "decra" roofing
tiles or other equal approved onto but excluding
steel truss laid to slope not exceeding 250
1012 Sm
B Translucent polycarbonic sky light roof covering
to atrium 0 Sm
C Extra over for raking cutting 130 Lm
Accessories, fixing as necessary to roof
covering
D Standard barrel half round ridge tile to match;
1320mm long to hip and ridge cap; and fixing to
position 3 Lm
E Ditto hip cap 26 Lm
F Extra for stone coat box barge cover 1320mm
long 0 Lm
G Ditto stone coat valley strip ditto 52 Lm
H Ditto stone coat side flashing ditto 305 Lm
Carried to collection
114
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ROOF CONSTRUCTION
All the following structural timber shall be
sawn second grade treated cypress with 9-
15% M.C.
A 100 x 75mm wall plate 245 Lm
B 75 x 50mm purlins 1125 Lm
C 150 x 50mm ditto 30 Lm
Trusses
Type No of pitch span (m) Rise (mm)
T17 178 Mono 3200 857
T18 1 Mono 4570 1225
T19 4 Mono 6000 2546
T20 2 Mono 6000 2546
The following in Trusses with nailed
connections including templates fillets, straps,
splices and hoisting approx 3.15metres above
ground level
D 150 x 50mm rafters 686 Lm
E 150 x 50mm joists 175 Lm
F 100 x 50mm ties and struts 755 Lm
G 100x50mm king post 175 Lm
H 100 x 50mm collar splice plate 270 Lm
Total to collection
115
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Other members
A 150 x 50mm valley rafters 104 Lm
B 150 x 50mm hip rafters 26 Lm
C 150 x 50mm common rafters 621 Lm
D 200 x 25mm ridge board 30 Lm
E 50x50mm battens 3755 Lm
Anchor bolts
F 12mm x 50 x 2mm diameter "J" bolts, 400mm
long with head nut and washers cast into cocrete
272 No
The following in wrot cypress
G 200 x 25mm thick facsia 0 Lm
H 25 x 100mm tongue & grooved boarding secret
nailed to and including 50 x 50mm celcured wrot
cypress bearers or brandering at 600mm centres
675 Sm
Total curried to collection
116
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Rainwater disposal
24g galvanized mild steel sheeting
A Raking flashing overall 400mm girth top and
turned and wedged into and including 50 x
50mm mortice in stone or concrete and rin in
with cement and sand (1:3) mortar and bottom
edge dressed over roofing 20 Lm
B Ditto horizontal 226 Lm
26g galvanized mild steel sheeting; all welds
ground smooth
C 200 x 200mm box gutter including soldered
joints in the running length fixed to fascia board
with and including brackets at approved centers
0 Lm
D Extra ; for blocked ends with 75mm dia. Outlet
100mm long 0 No
E 100mm Diameter fulbora outlet 26 No
Total carried to collection
117
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 100mm diameter 22 gauge galvanized metal rain
water downpipe fixed to wall with holder bats at
900mm centres 78 Lm
B Extra over downpipe for swan neck projecting
600mm 26 No
C Ditto shoe 26 No
Galvanised mild steel sheet 22 gauge
D 900mm girth lining to slopping gutters with
200mm laps comprising 15 x 200mm gutter and
200mm integral flashing each side 52 Lm
Carried to collection below
Collection
Brought forward page 114
Brought forward page 115
Brought forward page 116
Brought forward page 117
Brought forward page 118
Total element 07 roof construction to
summary
118
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 08
BALUSTRADING & RAILINGS
Wrot mahogany
A 100 x 50mm hand rail 0 Lm
3mm thick mild steel circular hollow
extrusion tubes
Composite balustrading comprising 50mm
diameter x 3mm thick top rail welded onto
25mm x 3mm secondary baluster 200mm long
at 450mm long; 50mm diameter primary
baluster at 900mm centres and 30mm
diameter x 2mm horizontal braces at 250mm
centres to detail including grinding welds
smooth fixing to concrete plinth and kerb and
end to walling
B Staircase railing raking 1250mm high 0 Lm
C Staircase railing horizontal curved to 1500mm
radii 1250mm high 0 Lm
D Balusrades railing horizontal 1250mm high 88 Lm
Total elemlent 08 to summary
119
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 09
PAINTING & DECORATING
ROOF
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint to:
A General surfaces of roof steel work 0 Kg
B General surfaces of 100mm diameter down pipe
girth over 300mm 25 Sm
WINDOWS
Prepare and supply two undercoasts stainer
and two finishing coats of vanish to:-
C Surfaces exceeding 100 but not exceeding
200mm girth window cill 211 Lm
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint to:-
D Metal Casement surface girth over 300mm
internally 409 Sm
E Ditto Externally 315 sm
Total to collection
120
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
DOOR
Prepare and apply two undercoats stainer and
two finishing coats of vanish to:-
A General surfaces of doors 603 Sm
B Surfaces not exceeding 100mm girth 1396 Lm
C Surfaces 100 to 200mm girth 0 Lm
D Surfaces exceeding 200 but n.e. 300mm girth 635 Lm
Prepare and apply one undercoat and two
finishing coats of gloss oil paint to:
E General surfaces of doors both side measured 77 Sm
F Surfaces not exceeding 100mm girth 171 LM
G Surfaces exceeding 100 but not exceeding
200mm girth 86 Lm
H Surfaces excceding 200 but not exceeding
300mm girth 0 lm
Touch up primer and apply one undercoats
and two finishing coasts of 1st qualtiy
supergloss paint to:
G General surfaces of metal (b.s.m.) 89 Sm
EXTERNAL FINISHES
Prepare and apply 3 No. coats matt vinyl
exterior wall finish as paint to:
K General rendered surfaces externally 1914 Sm
L Louvre block walling 114 Sm
M Soffites of gutter beam 258 Sm
Prepare and apply 1 No coats stainer and 2
No. finishing coats of varnish to:
N General surfaces of mazerah tiling 403 SM
Total carried to collection
121
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
INTERNAL FINISHES
Prepare and apply one undercoat and two
finishing coats of 1st quality silk vinyl paint
to:-
A General plastered surfaces of walls 4555 Sm
B General plastered surfaces of horizontal
suspended soffits 2273 Sm
C General plastered concrete surfaces 784 Sm
D Gypsum ceiling soffits 1483 Sm
E General surfaces of lourved block walling 114 Sm
F Surfaces not exceeding 100mm girth of cornice 2262 Lm
JOINERY FIXTURES
Prepare and apply two undercoats stainer and
two finishing coats of vanish to:-
G General surfaces of timbers 675 Sm
H Surfaces not exceeding 100mm girth 0 Lm
J Surfaces exceeding 100 but not exceeding
200mm girth 0 Lm
Total collection
122
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Metal work
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint paint to:-
A General surfaces of balcony balustrading 110 sm
B Ditto grilled surfaces (b.s.m) 563 Sm
Prepare and apply two undercoats stainer and
two finishing coats of varnish to:-
C Surfaces of rails exceeding 200mm but not
exceeding 300mm girth 0 Lm
Total carried to collection below
Collection page
Brought forward from page 120
Brought forward from page 121
Brought forward from page 122
Brought down from 123 above
Total element 09 to summary
123
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 10
JOINERY FIXTURES
A Provide a sum of Kenya shillings two million
five hundred thousand (Kshs. 2,500,000.00) SUM
Total element 10 to summary
124
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 11
STAIRCASES - 6 NO
Insitu concrete (1:2:4) reinforcement
Normal class 20/20mm vibrated
A Stairs 16 Cm
B 175mm thick landing 28 SM
C Stair beam 1 CM
Bars: Ribbedsteel: cold worked: B.S 4461
including bends, hooks tying wire, distance
block and spacers
D Various bars in reinforcement work 2500 KG
E 16mm diameter bars in beams 142 KG
F 8mm diameter bars in beams 50 KG
Sawn formwork to:
G Sloping soffits of stairs 67 SM
H Horizontal soffits of landings 28 SM
S Ditto edge of landing 150-225mm 54 LM
K Ditto sides and soffites of stair beam 15 SM
L Riser girth over 75mm - 150mm high 189 LM
M Open string of staircase 335mm external height
including cutting to profile of treads amd riser 45 LM
Carried to collection
125
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
12mm thick cement sand (1:6) plaster to:
A Beams 15 SM
B Sloping soffits of stairs 676 SM
C Horizontal soffit of landing 28 SM
20mm thick cement sand (1:3) screed
trowelled rough to receive terrazzo on:
D Tread 300mm wide 189 LM
E Riser 150mm high 207 LM
F Landing 28 SM
G Edge of upto stair string 300mm wide 45 LM
20mm polished terrazzo on:
H Tread 300mm wide 189 LM
J Riser 150mm high 207 LM
K Landing 28 SM
L Edge of stair 300mm wide 45 LM
M 20x100mm polished terrazzo skirting 93 LM
N Non slip carborundum inset to treads 189 LM
Total carried to collection
126
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
3mm thick mild steel circular hollow
extrusion tubes
Composite balustrading comprising 50mm
diameter x 3mm thick top rail welded onto
25mm x 3mm secondary baluster 200mm long
at 450mm long; 50mm diameter primary
baluster at 900mm centres and 30mm
diameter x 2mm horizontal braces at 250mm
centres to detail including grinding welds
smooth fixing to concrete plinth and kerb and
end to walling
A Staircase railing horizontal 1250mm high 36 Lm
B Staircase railing raking 1250mm high 46 Lm
Paintwork
C Touch up priming wrot and apply 1 No. coat
calcium plumbate primer and prepare and apply
3 No. coats glass enamel to steel surfaces
generally 103 Sm
Prepare and apply one undercoat and two
finishing coats of vinyl matt plastic emulsion
D Plastered concrete surfaces 660 Sm
Total carried to collection
127
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
COLLECTION
A Brought forward from page 125
B Brought forward from page 126
C Brought forward from page 127
Total Element No. 11 6 No. Staircases carried
to Summary
128
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO 12
RAMPS ( 2 NO)
Reinforced concrete class 25/20mm
mix (1: 1 1/2: 3) in:-
A Beams raking 20 CM
B Beams horizontal 2 CM
C 175mm thick suspended ramp 144 SM
D Ditto horizontal landings 35 SM
Sawn formwork to:
E Sides and soffities of beams, horizontal 28 SM
F Ditto, raking 233 SM
G Ditto curved to 1500mm radii 0 SM
H Soffites of raking suspended ramp slabs 144 SM
J Ditto horizontal landings 35 SM
K Edges of suspended Landing 150 to 225mm wide 32 LM
L Ditto to raking ramp 150 to 225mm wide 165 LM
M Ditto curved to 2500mm radii 17 LM
Steel reinforcement as described including
cutting to length bending hoisting and fixing
including all necessary tying wires and
spacing blocks (all provisional)
Ribbed bars
P 8mm diameter bars beams 690 KG
Q 16mm ditto in beams 1274 KG
R 10mm diameter bars in suspended slabs 4800 KG
Carried to collection
129
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Ramp finishes
12mm thick cement sand (1:6) plaster to:
A Beams 261 SM
B Sloping soffits of ramp 144 SM
C Horizontal soffites of landing 35 SM
D Raking edges of ramp 144 SM
20mm thick cement sand (1:3) screed backing
trowelled rough to receive terrazzo on:
E Horizontal floor bed 35 SM
F Sloping ramp 144 SM
G Edge of kerb 300mm wide 112 LM
20mm polished terrazzo on with 40x4mm
thick white pvc dividing strip
H Floors level 35 SM
J Sloping Ramp 144 SM
K Edge of kerb 300mm wide 112 LM
Prepare and apply one undercoat and two
finishing coats of vinyl matt plastic emulsion
L Beam 261 SM
M Sloping and horizontal soffits of ramp 144 SM
N Raking edges of ramp 90 SM
Total carried to Collection
130
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
COLLECTION
A Brought forward from page 129
B Brought forward from page130
Total Element No 12. 2 No. Ramps carried to
Summary
131
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 13
APRON
Precast paving slabs
A Excavate in normal soil not exceeding 300mm
deep; backfill with murram to form base to
receive PCC paving slabs (m/s) and cart away
arisings 600 Sm
B 150mm thick compacted murram bed
C Approved weed killer applied according to
manufacturer's instructions 600 Sm
D Premise200" Anti-termite treatment to murram 600 Sm
E 600 x 600 x 50mm thick PCC slabs on and
including 50mm sand bed jointed and pointed in
cement sand 1:3 mortar 600 Sm
F 100x100mm PCC channel on and including plain
concrete class Q in bed and hauch 400 Lm
Total for element No. 13 carried to summary
132
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
SUMMARY FOR GROUND FLOOR
1 Total from page 96 Substructure
2 Total from page 98 RC Frame
3 Total from page 99 Walling
4 Total from page 104 Doors
5 Total from page 107 Windows
6 Total from page 110 External finishes
7 Total from page 113 Internal finishes
8 Total from page 118 Roofing
9 Total from page 119 Balustrades and Railing
10 Total from page 123 Painting and Decorating
11 Total from page 124 Joinery fixtures
12 Total from page 128 6 No. Stair cases
13 Total from page 131 2 No. Ramp
14 Total from page 132 Apron
15 Provide a sum of Kenya shillings six million five
hundred thousand (kshs. 6,500,000.00) for
electrical installation
16 Provide Kenya shillings Two million, five
hundred thousand for Plumbing and drainage
TOTAL FOR GROUND FLOOR CARRIED
TO MAIN SUMMARY
133
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
1ST AND 2ND FLOOR
ELEMENT 01
REINFORCED CONCRETE
Superstructures
Vibrated reinforced concrete (1:1 1/2:3) Class
25/20mm in:
A Beams 196 Cm
B Gutter beam - 150mm thick 26 Cm
C Columns 66 Cm
D Suspended floor slabs, thickness 175mm 2273 Sm
E Suspended roof slabs 175mm 0 Sm
F 175 x200mm thick kerb 443 Lm
Reinforcement (all provisional)
Deformed bars as described in:
G 8mm diameter bars in beams 5883 Kgs
H 16mm ditto in beams 9710 Kgs
J 20mm ditto in beams 9476 Kgs
K 8mm dittto; in column 2155 Kgs
L 12mm ditto 0 Kgs
M 16mm ditto in column 0 Kgs
N 20mm ditto; 19800 Kgs
P 8mm ditto in gutter beam 1315 Kgs
Q 10mm ditto 2817 Kgs
R 16mm ditto 9607 Kgs
S 20mm ditto 9627 Kgs
T 10mm ditto in suspended floor slab 60723 Kgs
U 12mm ditto in kerb 1861 Kgs
Carried to collection
134
PROPOSED OUTPATIENT DEPARTMENT BLOCK AT RIFT VALLEY PROVINCIAL
GENERAL HOSPITAL NAKURU
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Sawn formwork to:
A Sides and soffits of beams 2051 Sm
B Sides and soffits of gutter beams 204 Sm
C Sides of columns 448 Sm
D Ditto curved 225mm radii 72 Sm
E Ditto curved 200mm radii 277 Sm
F Sides of columns circular on plan to 125mm 0 Sm
G Soffites of suspended floor slabs 2273 Sm
H Soffites of suspended roof slabs 0 Sm
J Edges of ditto 150-225mm wide 584 Lm
K Sides and soffites of kerb 166 Sm
Total carried to collection
Collection
Brought forward from page 134
Brought forward from page 135 Above
Total element 01 summary
135
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 02
WALLING
External walls
Hessian based Bituminous Damp Proof
Course bedded and jointed in cement sand
mortar 1:3
A 200mm wide 0 Lm
B 150mm wide 0 Lm
C Ditto; 100mm wide 0 Lm
D 200mm thick natural stone walling; medium
chiseled dressed; bedded and jointed in cement
and (1:3) mortar 631 Sm
E 200mm thick precast concrete louvre block
walling jointed and bedded in cement mortar
(1:4) 114 sm
Internal walls
Approved load bearing machine dressed
"Thika" natural stone walling bedded and
jointed in cement sand (1:3) mortar with
20mm wide hoop irons in every alternate
course
F 200mm thick walling 1093 Sm
G 150mm thick ditto 0 Sm
H 100mm thick 279 Sm
J 200mm thick dwarf wall 44 SM
Aluminium partition walling
K Powder coated anodised aluminium curtain
walling comprising 100 x 50mm extruded
aluminium frame sections at 900mm vertical
centers and 1050mm horizontal centres; panell
infilled with and including 6mm clear sheet
glass; 2700mm high overall 6 Lm
Total element 02 to summary
136
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 03
DOORS
Mild steel casement
A Double grilled door comprising 50 x 50 x 3mm
rolled hollow section frame all round in filled
with 30 x 30 x 2mm thick RHS vertical baluster
150mm center and similar horizontal member at
200mm centers in a straggered configuration
overall size 1800 x 2550mm high 4 No
B Ditto single leaf size 900 x 25500mm high 2 No
C Mild steel pannel double door overall size
1200x2550mm high in 2No. equal leaves each
leaf comprising of 6 No size 300x800mm high
10mm thick glass panels including 1200x200mm
and 1200x300high double plate complete with
100x50x3mm RHS framing and metal lugs
including purpose made hanging and locking
accessories once primer before delivery to the
site 2 No
D Ditto size 900x1500mm high 2 No
Total carried to collection
137
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Aluminium
A Aluminium sections 2mm thick 50 x 50mm
extrusions in top bottom and stiles and 100 x
50mm middle rail resulting bottom panel infilled
with 25mm thick blockboard laminate faced both
sides and top panel left open for glazing (m/s) in
door overall size 900 x 3050mm high comprising
900 x 950mm high top fanlight and 900 x
2100mm openable leaf complete with and
including locking devices 0 No
B Ditto double doors in 2No. Equal leaves overall
size 1800 x 3050mm high 0 No
Timber doors
C 50mm thick double paneled door overall size
1200 x 2400mm high all in solid mahogany in
two equal leaves each leaf comprising 150mm
top rail and stiles 200mm middle and bottom rail
resulting both panels instilled with bevel raised
and fielded panels 8 No 30000 240,000.00
Total carried to collection
138
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
HDF Mahogany veneered timber door
A 45mm thick moulded panel door as supplied by
BG Bison or other equal approved overall size
900 x 2550mm high with 950mm top fanlight 8 No
B 45mm ditto size 900x2400mm high with 300mm
fanlight ditto 0 No
C 45mm thick moulded panelled double door
Single swing in two equal leaves overall size
1200 x 2550mm high comprising of 300 x mm
high glazed fan light at to (m/s) 1200 x 2100mm
high openable leaves each faced with interior
quality mahogany veneer both sides and hard
wood lipped all round
40 No
D Ditto double swing 1650x2550mm high 1 No
Flush doors
E 45mm thick semi solid cored flush door in 2No.
Equal leaves hardwood lipped size 900 x
2550mm high faced both sides with interior
quality veneer facing both sides with 900 x 750
high glazed fanlight at top 10 No
F Size 900 x 2100mm ditto 8 No
G Ditto 1300 x 2100mm high double leaf 8 No
The following in wrot mahogany
H 200 x 50mm thick door frame with one labour
plugged 344 Lm
J 200 x 50mm transome, 2 labours 84 Lm
K 200x50mm mullion 2 labours 24 Lm
L 150x50mm thick frame with one labour plugged
48 Lm
M 150x50mm transome, 2 labours 7 Lm
N 100 x 50mm frame one labours plugging 85 Lm
Total carried to collection
139
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 40 x 15mm architrave with one labour 477 Lm
B 25mm quadrant 477 Lm
C 25 x 25mm glazing beads 282 Lm
4mm thick clear sheet glass to wood:
D Panes 0.5 to 1.00 square meters 38 Sm
E Panes 0.1to 0.5 square metres 3 Sm
4mm thick clear sheet to metal with glazing
compound
F Panes 0.5 to 1.00 square metres 1 Sm
Ironmongery
Supply and fix the following ironmongery as
"union" or other equal and approved to wood
with matching screws
G Cylinder Bathroom lock set with turn handle and
rose in satin anodized aluminium set of lever
furniture Ref. Toucan DS-051 16 No
H Double cylinder lock set with handle on plate
complete with lever furniture ditto. Ref.
Elegance LS-C85-306 SN 8 No
J 5 lever Deadlock to steel door 6 No
K Rebated double cylinder lock set for double door
with satin anodized aluminium set of lever
furniture Ref. Elegance LS-C85-306 SN 50 No
L 100mm stainless steel bearing butt hinges Ref.
BB-403030-SS 36 Prs
M 100mm brass parliament butt hinges Ref. P-
404040-SS 162 Prs
N Steel door lock 4 NO
Total carried to collection
140
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A Door closer as Union Ref. 8834 2 No
B 38mm diameter rubber door stopper plugged to
floor 152 No
C 150mm long lever action flush bolt Ref. No
U8052 50 No
Total carried to collection
Collection
Brought forward from page 137
Brought forward from page 138
Brought forward from page 139
Brought forward from page 140
Brought forward from page 141
Total element o3 carried to summary
141
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 04
WINDOWS
Fine chisseled "Blue Njiru" stone walling in
cement mortar
A 150 x 22mm cill, bedded and jointed in cement
and sand 1:1 and pointed in coloured cement
mortar 235 Lm
Supply and fix double metal curtain rods
from "Challenge Enginering" or other equal
and approved comprising of 25mm diameter
wrought iron front 16mm diameter rear rail
complete with fixing brackets, curtain holding
rings and decorative end stopsand all
necessary paintwork
B Curtain rods 218 Lm
Total to collection
142
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Casement - External
Supply, assemble and fix the following
purpose-made mild steel TOP HUNG
OUTWARD OPENABLE windows casement
complete with all opening accessories, 50 x
50mm thick frame units; including "snap on"
30mm wide permanent vent; building in ligs
to jambs; plugging and screwing head and
cill; bedding frames in waterproof cement
mortar and pointing in approved mastic
externally; fixing 6mm thick reflective glass
m.s oiling, easing and adjusting as described
in the following overall sizes
A 2100 x 1650mm high 64 No
B 2100 x 2000mm high 12 No
C 2100 x 750mm high 8 No
D 1500x1500mm high 0 No
E 1500x900mm high 0 No
F 900x600mm high 0 No
Glazing
G 4mm thick Reflective sheet glass and glazing in
panes 0.1-1.0sm with putty compound 272 Sm
H Ditto; obscured glass 13 Sm
Total carried to collection
143
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Casement - Internal
Supply, assemble and fix the following
purpose-made mild steel Top Hung Outward
Opening windows casement complete with all
opening accessories, 50 x 50mm thick frame
units; including "snap on" 30mm wide
permanent vent; building in ligs to jambs;
plugging and screwing head and cill; bedding
frames in waterproof cement mortar and
pointing in approved mastic externally; fixing
6mm thick reflective glass m.s oiling, easing
and adjusting as described in the following
overall sizes
A 2100 x 1050mm high 25 No
B 1500 x 1050mm high 10 No
Glazing
C 4mm thick reflective sheet glass and glazing in
panes 0.1-1.0sm with Putty compound 71 Sm
D Ditto; obscured glass 0 Sm
Total carried to collection
Collection
Brought forward from page 142
Brought forward from page 143
Brought forward from page 144
Total element 04 windows to summary
144
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 05
EXTERNAL FINISHES
Wall Finishes
A Extra over natural stone walling for neat flush
horizontal and vertical joints in coloured cement
mortar 0 Sm
Cement and sand (1:4)
B 15mm thick cement sand (1:4) render to columns
258 Sm
C Ditto beam 225 Sm
D Ditto wall facade surfaces 631 Sm
E Ditto sides of gutter beam 105 Sm
F Ditto sides and soffites of kerb 255 Sm
G Screeding to receive brick facing and mazerah
cladding 701 SM
Cement lime plaster: 15mm thick (1:2:9)
H Plaster to soffites of gutter 82 Sm
Rough and Tough wall finish
J Prepare and apply rough and touch exterior wall
finish as "Crown paints" or equivalent and to
approved colour 1219 Sm
Hand scratched burnt clay
K 250x75x35mm thick brick facing in cement
mortar 360 SM
Mazerah cladding
L 200x200x20mm thick cladding fixed with
cement and sand (1:2) mortar 341 SM
Total to collection
145
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Roof finishes
A Form groove in concrete for edge of felt roofing
and grout in cement sand mortar (1:4) including
forming bell mouth joint 117 Lm
Supply and fit APP water proofing membrane
(m/s) as Italbuild Ltd laid strictly in
accordance with manufacturer's printed
instructions
B Gutter cover laid to fall and cross fall on sceed 64 Sm
C 725mm high with top edge dressed into groove
(m/s) and bottom edge jointed to felt 120 Lm
D Dress felt around 100mm rain water outlet 16 No
Light weight roof screeds consisting of
cement, sand and pumice (1:3:7) with 6mm
layer of cement and sand topping laid to falls
and crossfalls.
E 25mm screed on concrete to receive felt roofing
sloping < 45 degrees from horizontal 64 Sm
F 15mm ditto to sides of gutter beam 120 Sm
G 50 x 50mm triangular fillet 263 Lm
H Work screed around 100mm rainwater outlet 16 No
Precast concrete class 20/12mm fair faced
finished smooth
J 250x50mm capping sunk weathered both
surfaces ad twice throated bedded and jointed in
cement mortar (1:3) 117 Lm
Total carried to collection
146
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Curtain walling
A Curtain walling in mild steel comprising main
100x50x4mm thick extruded rolled hollow
section (RHS) frame section at 700mm vertical
general spacing and 1200 horizontal centres
resulting panels infilled with 5mm thick
toughedned glass and glazing with putyy on
25mm 'T' sections 300mm wide and 600mm high
420 SM
Carried to collection
COLLECTION
Brought forwad from page 145
Brought forwad from page 146
Brought forwad from page 147
Total element 05 external finishes to
summary
147
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 06
INTERNAL FINISHES
FLOOR FINISHES
Cement and sand (1:4) screed
A Screed backing under floors finished with wood
float, thichness 32mm to receive ceramic tiles
(m/s) 135 Sm
B Ditto 20mm thick to floor to receive terrazzo
(m/s) 2124 Sm
Floor tiles
C 330 x 330 x 8mm thick ceramic tiles as
manufactured by "Flamingo Tiles" or other
approved non-slip tiles fixed with approved
adhesive in approved 135 Sm
D 100mm high ditto skirting 0 Lm
Polished white cement based terrazo
E 20mm thick paving to floor polished smooth
coomplete with and including 40x4mm thick
white plastic divindings strips 2124 Sm
F 20x100mm high skirting rounded top edge and
cored junction with floor 1397 Lm
Total to collection
148
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
WALL FINISHES
Cement and sand (1:4) screed
A Screed backing to wall wood floated thickness
15mm 386 Sm
Coloured glazed ceramic wall tiles and fittings
(cloakrooms)
B 200 x 300 x 6mm as manufactured by "Flamingo
Tiles" or other approved coloured tiles bedded
and jointed in cement and sand 1:1 and pointed
in coloured cement grouting 386 Sm
Cement Lime plaster; 15mm thick (1:2:9)
C Plaster to wall surfaces 3569 Sm
D Ditto concrete surface 688 Sm
E Ditto to soffits of suspended slabs 2273 Sm
CEILING FINISHES
Sawn cypress
F Suspended accoustic boards suspended to steel
truss complete with corner panel suspensions,
and flush jointing12mm thick 0 Sm
G 12mm gypsum ceiling lining to soffites in
approved pattern 245 Sm
H Extra over for forming trap door size 600 x
600mm 3 No
J 100 x 25mm decorative gypsum cornice 143 Lm
K 50x50mm Aluminium 'U' section channel fixed
to timber 629 Lm
Total carried to collection
149
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
COLLECTION
Brought forward from page 148
Brought down from page 149
Total element 06 internal finishes to summary
150
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 07
BALUSTRADING & RAILINGS
Wrot mahogany
A 100 x 50mm hand rail 0 Lm
3mm thick mild steel circular hollow
extrusion tubes
Composite balustrading comprising 50mm
diameter x 3mm thick top rail welded onto
25mm x 3mm secondary baluster 200mm long
at 450mm long; 50mm diameter primary
baluster at 900mm centres and 30mm
diameter x 2mm horizontal braces at 250mm
centres to detail including grinding welds
smooth fixing to concrete plinth and kerb and
end to walling
B Staircase railing raking 1250mm high 0 Lm
C Staircase railing horizontal curved to 1500mm
radii 1250mm high 0 Lm
D Balustrades railing horizontal 1250mm high 88 Lm
Total elemlent 07 to summary
151
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 08
PAINTING & DECORATING
ROOF
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint to:
A General surface of roof steel work 0 Kg
B General surfaces of 100mm diameter down pipe
girth over 300mm 15 Sm
WINDOWS
Prepare and supply two undercoasts stainer
and two finishing coats of vanish to:-
C Surface exceeding 100 but not exceeding 200mm
girth window cill 235 Lm
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint to:-
D Metal Casement surface girth over 300mm
internally 427 Sm
E Ditto Externally 285 sm
Total to collection
152
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
DOOR
Prepare and apply two undercoats stainer and
two finishing coats of vanish to:-
A General surface of doors 478 Sm
B Surface not exceeding 100mm girth 1066 Lm
C Surface 100 to 200mm girth 55 Lm
D Surface exceeding 200 but n.e. 300mm girth 483 Lm
Prepare and apply one undercoat and two
finishing coats of gloss oil paint to:
E General surface of doors both side measured 74 Sm
F Surface not exceeding 100mm girth 170 LM
G Surface exceeding 100 but not exceeding 200mm
girth 85 Lm
H Surfaces excceding 200 but not exceeding
300mm girth 0 lm
Touch up primer and apply one undercoats
and two finishing coasts of 1st qualtiy
supergloss paint to:
J General surfaces of metal (b.s.m.) 146 Sm
EXTERNAL FINISHES
Prepare and apply 3 No. coats exterior wall
finish as matt vinyl emulsion paint to:
K General rendered surface externally 1219 Sm
L Louvre block walling 114 Sm
M Soffites of gutter beam 105 Sm
Prepare and apply 1 No. coats stainer and 2
No. finishing coats of varnish to:
N General surfaces of mazerah tiling 341 Sm
Total carried to collection
153
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
INTERNAL FINISHES
Prepare and apply one undercoat and two
finishing coats of 1st quality silk vinyl paint
to:-
A General plastered surfaces of walls 3569 Sm
B General plastered surfaces of horizontal
suspended soffits 2273 Sm
C General plastered concrete surfaces 688 Sm
D Gypsum ceiling soffits 245 Sm
E General surfacees of lourved block walling 143 Lm
F Surface not exceeding 100mm girth of cornice 114 Sm
JOINERY FIXTURES
Prepare and apply two undercoats stainer and
two finishing coats of vanish to:-
G General surface of timber 258 Sm
H Surface not exceeding 100mm girth 0 Lm
J Surfaces exceeding 100 but not exceeding
200mm girth 0 Lm
Total collection
154
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Metal work
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint paint to:-
A General surface of balcony balustrading 127 sm
B Ditto grilled surface (b.s.m) 0 Sm
Prepare and apply two undercoats stainer and
two finishing coats of varnish to:-
C Surface of rails exceeding 200mm but not
exceeding 300mm girth 102 Lm
Total carried to collection below
Collection page
Brought forward from page 152
Brought forward from page 153
Brought forward from page 154
Brought forward from page 155
Total element 08 to summary
155
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Element No. 09
JOINERY FIXTURES
A Provide a sum of kenya shillings Two Million,
five hundred thousand (Kshs. 2,500,000.00) SUM
Total element 09 to summary
156
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 10
STAIRCASES
Insitu concrete (1:2:4) reinforcement
Normal class 20/20mm vibrated
A Stairs 16 Cm
B 175mm thick landing 28 SM
C Stair beam 1 CM
Bars: Ribbedsteel: cold worked: B.S 4461
including bends, hooks tying wire, distance
block and spacers
D Various bars in reinforcement work 2500 KG
E 16mm diameter bars in beams 142 KG
F 8mm diameter bars in beams 50 KG
Sawn formwork to:
G Sloping soffits of stairs 67 SM
H Horizontal soffits of landings 28 SM
S Ditto edge of landing 150-225mm 54 LM
K Ditto sides and soffites of stair beam 15 SM
L Riser girth over 75mm - 150mm high 189 LM
M Open string of staircase 335mm external height
including cutting to profile of treads amd riser 45 LM
Carried to collection
157
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
12mm thick cement sand (1:6) plaster to:
A Beams 15 SM
B Sloping soffits of stairs 676 SM
C Horizontal soffit of landing 28 SM
20mm thick cement sand (1:3) screed
trowelled rough to receive terrazzo on:
D Tread 300mm wide 189 LM
E Riser 150mm high 207 LM
F Landing 28 SM
G Edge of upto stair string 300mm wide 45 LM
20mm polished terrazzo on:
H Tread 300mm wide 189 LM
J Riser 150mm high 207 LM
K Landing 28 SM
L Edge of stair 300mm wide 45 LM
M 20x100mm polished terrazzo skirting 93 LM
N Non slip carborundum inset to treads 189 LM
Total carried to collection
158
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
3mm thick mild steel circular hollow
extrusion tubes
Composite balustrading comprising 50mm
diameter x 3mm thick top rail welded onto
25mm x 3mm secondary baluster 200mm long
at 450mm long; 50mm diameter primary
baluster at 900mm centres and 30mm
diameter x 2mm horizontal braces at 250mm
centres to detail including grinding welds
smooth fixing to concrete plinth and kerb and
end to walling
A Staircase railing horizontal 1250mm high 36 Lm
B Staircase railing raking 1250mm high 46 Lm
Paintwork
C Touch up priming wrot and apply 1 No. coat
calcium plumbate primer and prepare and apply
3 No. coats glass enamel to steel surfaces
generally 103 Sm
Prepare and apply one undercoat and two
finishing coats of vinyl matt plastic emulsion
D Plastered concrete surfaces 660 Sm
Total carried to collection
159
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
COLLECTION
A Brought forward from page 159
B Brought forward from page 158
C Brought forward from page 159
Total Element No. 10 Staircases carried to
Summary
160
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO 11
RAMPS ( 2 NO)
Reinforced concrete class 25/20mm
mix (1: 1 1/2: 3) in:-
A Beams raking 20 CM
B Beams horizontal 2 CM
C 175mm thick suspended ramp 144 SM
D Ditto horizontal landings 35 SM
Sawn formwork to:
E Sides and soffities of beams, horizontal 28 SM
F Ditto, raking 233 SM
G Ditto curved to 1500mm radii 0 SM
H Soffites of raking suspended ramp slabs 144 SM
J Ditto horizontal landings 35 SM
K Edges of suspended Landing 150 to 225mm wide 32 LM
L Ditto to raking ramp 150 to 225mm wide 165 LM
M Ditto curved to 2500mm radii 17 LM
Steel reinforcement as described including
cutting to length bending hoisting and fixing
including all necessary tying wires and
spacing blocks (all provisional)
Ribbed bars
P 8mm diameter bars beams 690 KG
Q 16mm ditto in beams 1274 KG
R 10mm diameter bars in suspended slabs 4800 KG
Carried to collection
161
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Ramp finishes
12mm thick cement sand (1:6) plaster to:
A Beams 261 SM
B Sloping soffits of ramp 144 SM
C Horizontal soffites of landing 35 SM
D Raking edges of ramp 144 SM
20mm thick cement sand (1:3) screed backing
trowelled rough to receive terrazzo on:
E Horizontal floor bed 35 SM
F Sloping ramp 144 SM
G Edge of kerb 300mm wide 112 LM
20mm polished terrazzo on with 40x4mm
thick white pvc dividing strip
H Floors level 35 SM
J Sloping Ramp 144 SM
K Edge of kerb 300mm wide 112 LM
Prepare and apply one undercoat and two
finishing coats of vinyl matt plastic emulsion
L Beam 261 SM
M Sloping and horizontal soffits of ramp 144 SM
N Raking edges of ramp 90 SM
Total carried to Collection
162
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
COLLECTION
A Brought forward from page 161
B Brought forward from page 162
Total Element No 11. 2 No. Ramps carried to
Summary
163
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO.12
ROOF CONSTRUCTION, COVERING AND
RAIN WATER DISPOSAL
Roof covering
A 1320x370mm stone coated steel "decra" roofing
tiles or other equal approved onto but excluding
steel truss laid to slope not exceeding 250
275 Sm
B Translucent polycarbonic sky light roof covering
to atrium 0 Sm
C Extra over for raking cutting 53 Lm
Accessories, fixing as necessary to roof
covering
D Standard barrel half round ridge tile to match;
1320mm long to hip and ridge cap; and fixing to
position 43 Lm
E Ditto hip cap 35 Lm
F Extra for stone coat box barge cover 1320mm
long 117 Lm
G Ditto stone coat valley strip ditto 18 Lm
H Ditto stone coat side flashing ditto 20 Lm
Carried to collection
164
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ROOF CONSTRUCTION
All the following structural timber shall be
sawn second grade treated cypress with 9-
15% M.C.
A 100 x 75mm wall plate 105 Lm
B 75 x 50mm purlins 307 Lm
C 150 x 50mm ditto 49 Lm
The following in Trusses with nailed
connections including templates fillets, straps,
splices and hoisting approx 6.3metres above
ground level
Trusses
Type No off pitch span (Mm) Rise (mm)
T22 3 Double 7350 1009
T23 2 Mono 5325 1009
T24 24 Double 6000 804
T25 4 Double 6000 536
D 150 x 50mm rafters 118 Lm
E 150 x 50mm joists 180 Lm
F 100 x 50mm ties and struts 171 Lm
G 100x50mm king post 18 Lm
H 100 x 50mm collar splice plate 30 Lm
Total to collection
165
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Other members
A 150 x 50mm valley rafters 35 Lm
B 150 x 50mm hip rafters 35 Lm
C 150 x 50mm common rafters 343 Lm
D 200 x 25mm ridge board 43 Lm
E 50x50mm battens 3755 Lm
Anchor bolts
F 12mm x 50 x 2mm diameter "J" bolts, 400mm
long with head nut and washers cast into cocrete
120 No
The following in wrot cypress
G 200 x 25mm thick facsia 0 Lm
H 25 x 100mm tongue & grooved boarding secret
nailed to and including 50 x 50mm celcured wrot
cypress bearers or brandering at 600mm centres
258 Sm
Total curried to collection
166
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Rainwater disposal
24g galvanized mild steel sheeting
A Raking flashing overall 400mm girth top and
turned and wedged into and including 50 x
50mm mortice in stone or concrete and rin in
with cement and sand (1:3) mortar and bottom
edge dressed over roofing 20 Lm
B Ditto horizontal 0 Lm
26g galvanized mild steel sheeting; all welds
ground smooth
C 200 x 200mm box gutter including soldered
joints in the running length fixed to fascia board
with and including brackets at approved centers
0 Lm
D Extra ; for blocked ends with 75mm dia. Outlet
100mm long 0 No
E 100mm Diameter fulbora outlet 16 No
Total carried to collection
167
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 100mm diameter 22 gauge galvanized metal rain
water downpipe fixed to wall with holder bats at
900mm centres 48 Lm
B Extra over downpipe for swan neck projecting
600mm 26 No
C Ditto shoe 26 No
Galvanised mild steel sheet 22 gauge
D 900mm girth lining to slopping gutters with
200mm laps comprising 15 x 200mm gutter and
200mm integral flashing each side 52 Lm
Carried to collection below
Collection
Brought forward page 164
Brought forward page 165
Brought forward page 166
Brought forward page 167
Brought forward page 168
Total element 07 roof construction to
summary
168
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
SUMMARY FOR 1ST & 2ND FLOORS
1 Total from page 135 RC frame
2 Total from page 136 Walling
3 Total from page 141 Doors
4 Total from page 144 Windows
5 Total from page 147 External Finishes
6 Total from page 150 Internal Finishes
7 Total from page 151Balustrades & Railings
8 Total from page 155 Painting & Decorating
9 Total from page 156 joinery and fixtures
10 Total from page 160 Stair cases
11 Total from page 163 2 No. Ramp
12 Provide a sum of Kenya shillings Three million
five hundred thousand (kshs. 3,500,000.00) for
electrical installation
13 Provide Kenya shillings Three million, five
hundred thousand for Plumbing and drainage
Sub-Total for 1 No Typical floor
Multiply by two (02) x2
SUB-TOTAL
14 Total from page 168 Roofing
Total for 1st & 2nd floors Carried to
summary
169
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
3RD FLOOR
ELEMENT 01
REINFORCED CONCRETE FRAME
Superstructures
Vibrated reinforced concrete (1:1 1/2:3) Class
25/20mm in:
A Beams 208 Cm
B Gutter beam - 150mm thick 309 Cm
C Columns 70 Cm
D Suspended slabs, thickness 150mm 2357 Sm
E 150 x200mm thick kerb 443 Lm
Reinforcement (all provisional)
Deformed bars as described in:
F 8mm diameter bars in beams 6247 Kgs
G 16mm ditto in beams 10386 Kgs
H 20mm ditto in beams 10004 Kgs
J 8mm dittto; in column 2253 Kgs
K 12mm ditto 0 Kgs
L 16mm ditto in column 13065 Kgs
M 20mm ditto; 32 Kgs
N 8mm ditto in gutter beam 15833 Kgs
P 10mm ditto 33815 Kgs
Q 16mm ditto 9793 Kgs
R 20mm ditto 6953 Kgs
S 10mm in suspended floor slab 60723 Kgs
T 12mm ditto in kerb 766 Kgs
Carried to collection
170
PROPOSED OUTPATIENT DEPARTMENT AT RIFT VALLEY PROVINCIAL GENERAL
HOSPITAL
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Sawn formwork to:
A Sides and soffits of beams 2192 Sm
B Sides and soffits of gutter beams 709 Sm
C Sides of columns 448 Sm
D Ditto curved 225mm radii 72 Sm
E Ditto curved 200mm radii 316 Sm
F Sides of columns circular on plan to 125mm 0 Sm
G Soffites of suspended slabs 2357 Sm
H Edges of ditto 150-225mm wide 573 Lm
J Sides and soffites of kerb 166 Sm
Total carried to collection
Collection
Brought forward from page PGH/170
Brought forward from page 171 Above
Total element 01 summary
171
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 02
WALLING
External walls
Hessian based Bituminous Damp Proof
Course bedded and jointed in cement sand
mortar 1:3
A 200mm wide 0 Lm
B 150mm wide 0 Lm
C Ditto; 100mm wide 0 Lm
D 200mm thick natural stone walling; medium
chiseled dressed; bedded and jointed in cement
and (1:3) mortar 731 Sm
E 200mm thick precast concrete louvre block
walling jointed and bedded in cement mortar
(1:4) 114 sm
Internal walls
Approved load bearing machine dressed
"Thika" natural stone walling bedded and
jointed in cement sand (1:3) mortar with
20mm wide hoop irons in every alternate
course
F 200mm thick walling 1120 Sm
G 150mm thick ditto 0 Sm
H 100mm thick 381 Sm
J 200mm thick dwarf wall 77 SM
Aluminium Partiion
K Powder coated anodised aluminium curtain
walling comprising 100 x 50mm extruded
aluminium frame sections at 900mm vertical
centers and 1050mm horizontal centres; panell
infilled with and including 6mm clear sheet
glass; 2700mm high overall 6 Lm
Total element 02 to summary
172
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 03
DOORS
Mild steel casement
A Double grilled door comprising 50 x 50 x 3mm
rolled hollow section frame all round in filled
with 30 x 30 x 2mm thick RHS vertical baluster
150mm center and similar horizontal member at
200mm centers in a straggered configuration
overall size 1800 x 2550mm high 4 No
B Ditto single leaf size 900 x 25500mm high 2 No
C Mild steel pannel double door overall size
1200x2550mm high in 2No. equal leaves each
leaf comprising of 6 No size 300x800mm high
10mm thick glass panels including 1200x200mm
and 1200x300high double plate complete with
100x50x3mm RHS framing and metal lugs
including purpose made hanging and locking
accessories once primer before delivery to the
site 2 No
D Ditto size 900x1500mm high 2 No
Total carried to collection
173
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Aluminium
A Aluminium sections 2mm thick 50 x 50mm
extrusions in top bottom and stiles and 100 x
50mm middle rail resulting bottom panel infilled
with 25mm thick blockboard laminate faced both
sides and top panel left open for glazing (m/s) in
door overall size 900 x 3050mm high comprising
900 x 950mm high top fanlight and 900 x
2100mm openable leaf complete with and
including locking devices 0 No
B Ditto double doors in 2No. Equal leaves overall
size 1800 x 3050mm high 0 No
Timber doors
C 50mm thick double paneled door overall size
1200 x 2400mm high all in solid mahogany in
two equal leaves each leaf comprising 150mm
top rail and stiles 200mm middle and bottom rail
resulting both panels instilled with bevel raised
and fielded panels 8 No
Total carried to collection
174
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
HDF Mahogany veneered timber door
A 45mm thick moulded panel door as supplied by
BG Bison or other equal approved overall size
900 x 2850mm high with 950mm top fanlight 11 No
B 45mm ditto size 900x2400mm high with 300mm
fanlight ditto 0 No
C 45mm thick moulded panelled double door in
two equal leaves overall size 1200 x 2400mm
high comprising of 300 x mm high glazed fan
light at to (m/s) 1200 x 2100mm high openable
leaves each faced with interior quality
mahogany veneer both sides and hard wood
lipped all round 45 No
Flush doors
D 45mm thick semi solid cored flush door in 2No.
Equal leaves hardwood lipped size 900 x
2850mm high faced both sides with interior
quality veneer facing both sides with 900 x 750
high glazed fanlight at top 8 No
E Size 900 x 2100mm ditto 9 No
F Ditto 1300 x 2100mm high double leaf 6 No
The following in wrot mahogany
G 200 x 50mm thick door frame with one labour
plugged 331 Lm
H 200 x 50mm transome, 2 labours 88 Lm
J 200x50mm mullion 24 Lm
K 150x50mm thick frame with one labour plugged
66 Lm
L 150x50mm transome, 2 labours 10 Lm
M 100 x 50mm frame one labours plugging 79 Lm
Total carried to collection
175
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 40 x 15mm architrave with one labour 476 Lm
B 25mm quadrant 476 Lm
C 25 x 25mm glazing beads 300 Lm
4mm thick clear sheet glass to wood:
D Panes 0.5 to 1.00 square meters 40 Sm
E Panes 0.1to 0.5 square metres 4 Sm
4mm thick clear sheet to metal with glazing
compound
F Panes 0.5 to 1.00 square metres 1 Sm
Ironmongery
Supply and fix the following ironmongery as
"union" or other equal and approved to wood
with matching screws
G Cylinder Bathroom lock set with turn handle and
rose in satin anodized aluminium set of lever
furniture Ref. Toucan DS-051 15 No
H Double cylinder lock set with handle on plate
complete with lever furniture ditto. Ref.
Elegance LS-C85-306 SN 11 No
J 5 lever Deadlock to steel door 6 No
K Double cylinder lock set for double door with
satin anodized aluminium set of lever furniture
Ref. Elegance LS-C85-306 SN 53 No
L 100mm stainless steel bearing butt hinges Ref.
BB-403030-SS 48 Prs
M 100mm brass parliament butt hinges Ref. P-
404040-SS 31.5 Prs
N Steel door lock 4 NO
Total carried to collection
176
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A Door closer as Union Ref. 8834 2 No
B 38mm diameter rubber door stopper plugged to
floor 138 No
C 150mm long lever action flush bolt Ref. No
U8052 53 No
Total carried to collection
Collection
Brought forward from page 173
Brought forward from page 174
Brought forward from page 175
Brought forward from page 176
Brought forward from page 177
Total element o3 carried to summary -
177
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 04
WINDOWS
Fine chisseled "Blue Njiru" stone walling in
cement mortar
A 150 x 22mm cill, bedded and jointed in cement
and sand 1:1 and pointed in coloured cement
mortar 264 Lm
Supply and fix double metal curtain rods
from "Challenge Enginering" or other equal
and approved comprising of 25mm diameter
wrought iron front 16mm diameter rear rail
complete with fixing brackets, curtain holding
rings and decorative end stopsand all
necessary paintwork
B Curtain rods 218 Lm
Total to collection
178
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Casement - External
Supply, assemble and fix the following
purpose-made mild steel TOP HUNG
OUTWARD OPENABLE windows casement
complete with all opening accessories, 50 x
50mm thick frame units; including "snap on"
30mm wide permanent vent; building in ligs
to jambs; plugging and screwing head and
cill; bedding frames in waterproof cement
mortar and pointing in approved mastic
externally; fixing 6mm thick reflective glass
m.s oiling, easing and adjusting as described
in the following overall sizes
A 2100 x 1650mm high 64 No
B 2100 x 2000mm high 12 No
C 2100 x 750mm high 8 No
D 2400x1500mm high 12 No
E 1500x900mm high 0 No
F 900x600mm high 0 No
Glazing
G 4mm thick Reflective sheet glass and glazing in
panes 0.1-1.0sm with putty compound 307 Sm
H Ditto; obscured glass 13 Sm
Total carried to collection
179
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Casement - Internal
Supply, assemble and fix the following
purpose-made mild steel Top Hung Outward
Opening windows casement complete with all
opening accessories, 50 x 50mm thick frame
units; including "snap on" 30mm wide
permanent vent; building in ligs to jambs;
plugging and screwing head and cill; bedding
frames in waterproof cement mortar and
pointing in approved mastic externally; fixing
6mm thick reflective glass m.s oiling, easing
and adjusting as described in the following
overall sizes
A 2100 x 1050mm high 25 No
B 1500 x 1050mm high 10 No
Glazing
C 4mm thick reflective sheet glass and glazing in
panes 0.1-1.0sm with Putty compound 71 Sm
D Ditto; obscured glass 0 Sm
Total carried to collection
Collection
Brought forward from page 178
Brought forward from page 179
Brought forward from page 180 above
Total element 04 windows to summary
180
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 05
EXTERNAL FINISHES
Wall Finishes
A Extra over natural stone walling for neat flush
horizontal and vertical joints in coloured cement
mortar 0 Sm
Cement and sand (1:4)
B 15mm thick cement sand (1:4) render to columns
268 Sm
C Ditto beam 256 Sm
D Ditto wall facade surfaces 722 Sm
E Ditto sides of gutter beam 437 Sm
F Ditto sides and soffites of kerb 255 Sm
G Screeding to receive brick facing 802 SM
Cement lime plaster: 15mm thick (1:2:9)
H Plaster to soffites of gutter 436 Sm
Rough and Tough wall finish
J Prepare and apply rough and touch exterior wall
finish as "Crown paints" or equivalent and to
approved colour 1582 Sm
Hand scratched burnt clay
K 250x75x35mm thick brick facing in cement
mortar 461 SM
Mazerah cladding
L 200x200x20mm thick cladding fixed withcement
and sand (1;2) mortar 341 SM
Total to collection
181
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Roof finishes
A Form groove in concrete for edge of felt roofing
and grout in cement sand mortar (1:4) including
forming bell mouth joint 492 Lm
Supply and fit APP water proofing membrane
(m/s) as Italbuild Ltd laid strictly in
accordance with manufacturer's printed
instructions
B Gutter cover laid to fall and cross fall on sceed 267 Sm
C 725mm high with top edge dressed into groove
(m/s) and bottom edge jointed to felt 500 Lm
D Dress felt around 100mm rain water outlet 46 No
Light weight roof screeds consisting of
cement, sand and pumice (1:3:7) with 6mm
layer of cement and sand topping laid to falls
and crossfalls.
E 25mm screed on concrete to receive felt roofing
sloping < 45 degrees from horizontal 267 Sm
F 15mm ditto to sides of gutter beam 500 Sm
G 50 x 50mm triangular fillet 492 Lm
H Work screed around 100mm rainwater outlet 46 No
Precast concrete class 20/12mm fair faced
finished smooth
J 250x50mm capping sunk weathered both
surfaces ad twice throated bedded and jointed in
cement mortar (1:3) 497 Lm
Total carried to collection
182
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
COLLECTION
Brought forwad from page 181
Brought forwad from page182
Total element 05 external finishes to
summary
183
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT 06
INTERNAL FINISHES
FLOOR FINISHES
Cement and sand (1:4) screed
A Screed backing under floors finished with wood
float, thichness 32mm to receive ceramic tiles
(m/s) 1317 Sm
B Ditto 20mm thick to floor to receive terrazzo
(m/s) 961 Sm
Floor tiles
C 330 x 330 x 8mm thick ceramic tiles as
manufactured by "Flamingo Tiles" or other
approved non-slip tiles fixed with approved
adhesive in approved 1317 Sm
D 100mm high ditto skirting 913 Lm
Polished white cement based terrazo
E 20mm thick paving to floor polished smooth
coomplete with and including 40x4mm thick
white plastic divindings strips 961 Sm
F 20x100mm high skirting rounded top edge and
cored junction with floor 603 Lm
Total to collection
184
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
WALL FINISHES
Cement and sand (1:4) screed
A Screed backing to wall wood floated thickness
15mm 424 Sm
Coloured glazed ceramic wall tiles and fittings
(cloakrooms)
B 200 x 300 x 6mm as manufactured by "Flamingo
Tiles" or other approved coloured tiles bedded
and jointed in cement and sand 1:1 and pointed
in coloured cement grouting 424 Sm
Cement Lime plaster; 15mm thick (1:2:9)
C Plaster to wall surfaces 3970 Sm
D Ditto concrete surface 827 Sm
E Ditto to soffits of suspended slabs 2357 Sm
CEILING FINISHES
Sawn cypress
F Suspended accoustic boards suspended to steel
truss complete with corner panel suspensions,
and flush jointing12mm thick 202 Sm
G 19mm gypsum ceiling lining to soffites in
approved pattern 0 Sm
H Extra over for forming trap door size 600 x
600mm 0 No
J 100 x 25mm decorative gypsum cornice 1751 Lm
K 50x50mm Aluminium 'U' section channel fixed
to timber 520 Lm
Total carried to collection
185
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Carried to collection
COLLECTION
Brought forward from page 184
Brought down from page 185
Total element 06 internal finishes to summary
186
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO.7
ROOF CONSTRUCTION, COVERING AND
RAIN WATER DISPOSAL
Roof covering
A 1320x370mm stone coated steel "decra" roofing
tiles or other equal approved onto but excluding
steel truss laid to slope not exceeding 250
5616 Sm
B Translucent polycarbonic sky light roof covering
to atrium 209 Sm
C Extra over for raking cutting 1024 Lm
Accessories, fixing as necessary to roof
covering
D Standard barrel half round ridge tile to match;
1320mm long to hip and ridge cap; and fixing to
position 117 Lm
E Ditto hip cap 248 Lm
F Extra for stone coat box barge cover 1320mm
long 0 Lm
G Ditto stone coat valley strip ditto 264 Lm
H Ditto stone coat side flashing ditto 497 Lm
Carried to collection
187
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ROOF CONSTRUCTION
All the following structural timber shall be
sawn second grade treated cypress with 9-
15% M.C.
A 100 x 75mm wall plate 651 Lm
B 75 x 50mm purlins 5352 Lm
C 150 x 50mm ditto 265 Lm
The following in Trusses with nailed
connections including templates fillets, straps,
splices and hoisting approx 9.50 and 13.00
metres and above ground level
Trusses
Type No off pitch span (mm) Rise (mm)
T22 3 Double 7350 1009
T23 2 Mono 5325 1009
T24 7 Mono 6000 804
T25 4 Mono 6000 536
D 150 x 50mm rafters 1617 Lm
E 150 x 50mm joists 1594 Lm
F 100 x 50mm ties and struts 2352 Lm
G 100x50mm king post 275 Lm
H 100 x 50mm collar splice plate 4460 Lm
Total to collection
188
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Other members
A 150 x 50mm valley rafters 529 Lm
B 150 x 50mm hip rafters 248 Lm
C 150 x 50mm common rafters 117 Lm
D 200x25mm ridge board 3755 Lm
E 50x50mm battens
Anchor bolts
F 12mm x 50 x 2mm diameter "J" bolts, 400mm
long with head nut and washers cast into cocrete
730 No
The following in wrot cypress
G 200 x 25mm thick facsia 0 Lm
H 25 x 100mm tongue & grooved boarding secret
nailed to and including 50 x 50mm celcured wrot
cypress bearers or brandering at 600mm centres
90 Sm
Total curried to collection
189
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Rainwater disposal
24g galvanized mild steel sheeting
A Raking flashing overall 400mm girth top and
turned and wedged into and including 50 x
50mm mortice in stone or concrete and rin in
with cement and sand (1:3) mortar and bottom
edge dressed over roofing 0 Lm
B Ditto horizontal 100 Lm
26g galvanized mild steel sheeting; all welds
ground smooth
C 200 x 200mm box gutter including soldered
joints in the running length fixed to fascia board
with and including brackets at approved centers
0 Lm
D Extra ; for blocked ends with 75mm dia. Outlet
100mm long 0 No
E 100mm Diameter fulbora outlet 40 No
Total carried to collection
190
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
A 100mm diameter 22 gauge galvanized metal rain
water downpipe fixed to wall with holder bats at
900mm centres 400 Lm
B Extra over downpipe for swan neck projecting
600mm 46 No
C Ditto shoe 46 No
Galvanised mild steel sheet 22 gauge
D 900mm girth lining to slopping gutters with
200mm laps comprising 15 x 200mm gutter and
200mm integral flashing each side 264 Lm
Carried to collection below
Collection
Brought forward page 187
Brought forward page 188
Brought forward page 189
Brought forward page 190
Brought forward page 191
Total element 07 roof construction to
summary
191
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 08
BALUSTRADING & RAILINGS
Wrot mahogany
A 100 x 50mm hand rail 102 Lm
3mm thick mild steel circular hollow
extrusion tubes
Composite balustrading comprising 50mm
diameter x 3mm thick top rail welded onto
25mm x 3mm secondary baluster 200mm long
at 450mm long; 50mm diameter primary
baluster at 900mm centres and 30mm
diameter x 2mm horizontal braces at 250mm
centres to detail including grinding welds
smooth fixing to concrete plinth and kerb and
end to walling
B Staircase railing raking 1250mm high 0 Lm
C Staircase railing horizontal curved to 1500mm
radii 1250mm high 0 Lm
D Passage balustrades railing horizontal 1250mm
high 102 Lm
Total elemlent 08 to summary
192
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO. 10
PAINTING & DECORATING
ROOF
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint to:
A General surfaces of roof steel work 0 Kg
B General surfaces of 100mm diameter down pipe
girth over 300mm 126 Lm
WINDOWS
Prepare and supply two undercoasts stainer
and two finishing coats of vanish to:-
C Surfaces exceeding 100 but not exceeding
200mm girth window cill 264 Lm
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint to:-
D Metal Casement surfaces girth over 300mm
internally 462 Sm
E Ditto Externally 320 sm
Total to collection
193
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
DOOR
Prepare and apply two undercoats stainer and
two finishing coats of vanish to:-
A General surfaces of doors 509 Sm
B Surfaces not exceeding 100mm girth 1095 Lm
C Surfaces 100 to 200mm girth 0 Lm
D Surfaces exceeding 200 but n.e. 300mm girth 495 Lm
Prepare and apply one undercoat and two
finishing coats of gloss oil paint to:
E General surfaces of doors both side measured 67 Sm
F Surfaces not exceeding 100mm girth 158 LM
G Surfaces exceeding 100 but not exceeding
200mm girth 79 Lm
H Surfaces excceding 200 but not exceeding
300mm girth 0 lm
Touch up primer and apply one undercoats
and two finishing coasts of 1st qualtiy
supergloss paint to:
J General surfaces of metal (b.s.m.) 146 Sm
EXTERNAL FINISHES
Prepare and apply rough and tough exterior
wall finish as paint to:
K General rendered surfaces externally 1497 Sm
L Louvre block walling 114 Sm
M Soffites of gutter beams 304 Sm
Prepare and apply 1 No. coats stainer and 2
No. finishing coats of varnish to:
N General surfaces of mazerah tiling 341 Sm
Total carried to collection
194
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
INTERNAL FINISHES
Prepare and apply one undercoat and two
finishing coats of 1st quality silk vinyl paint
to:-
A General plastered surfaces of walls 3970 Sm
B General plastered surfaces of horizontal
suspended soffits 2357 Sm
C General plastered concrete surfaces 827 Sm
D Gypsum ceiling soffits 0 Sm
E General surfaces of lourved block walling 114 Sm
F Surfaces not exceeding 100mm girth of cornice 1751 Lm
JOINERY FIXTURES
Prepare and apply two undercoats stainer and
two finishing coats of vanish to:-
G General surface of timber 0 Sm
H Surfaces not exceeding 100mm girth 780 Lm
J Surfaces exceeding 100 but not exceeding
200mm girth 0 Lm
Total collection
195
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Metal work
Touch up primer and apply one undercoat
and two finishing coats of 1st quality
supergloss paint paint to:-
A General surfaces of balcony balustrading 127 sm
B Ditto grilled surface s(b.s.m) 841 Sm
Prepare and apply two undercoats stainer and
two finishing coats of varnish to:-
C Surfaces of rails exceeding 200mm but not
exceeding 300mm girth 102 Lm
Total carried to collection below
Collection page
Brought forward from page 193
Brought forward from page 194
Brought forward from page 195
Brought down from 196 above
Total element 08 to summary
196
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
ELEMENT NO . 9
JOINERY FIXTURES
A Provide a sum of Kenya shillings two million
five hundred thousand (Kshs. 2,500,000.00 SUM
Total element 09 to summary
197
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
SUMMARY FOR 3RD FLOOR
1 Total from page 171- RC Frame
2 Total from page 172- Walling
3 Total from page 177 - Doors
4 Total from page 180 - Windows
5 Total from page 183 - External finishes
6 Total from page 186 - Internal finishes
7 Total from page 191 - Roofing
8 Total from page 192 - Balustrades and Railing
9 Total from page 196 - Painting and decorations
10 Total from page 197 - joinery and fixtures
11 Provide a sum of Kenya shillings Three million,
five hundred thousand for electrical installation
12 Provide a sum of Kenya shillings Two million,
five hundred thousand for plumbing and
Drainage
Total for 2nd floor Carried to summary
198
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
PROVISIONAL SUMS
A Provide sum of Kshs. Ten million (Kshs.
10,000,000.00) only for project management SUM
B Add for profit %
C Provide sum of Kshs.Fourty million (Kshs.
40,000,000.00) only for contingencies SUM
D Allow the Provisional Sum of Kshs 1,250,000 in
connection with provision of furniture and other
equipment for Project Manager's office
Furniture and equipment to revert back to the
Employer at the end of the contract SUM
E Allow the Provisional Sum of Kshs 250,000.00 in
connection with the Project Manager's
miscellenous account for due perfomance of the
Project Manager's office to be spent in whole or S
part as instructed by the Project Manger and to be
reimbursed against receipts. SUM
Site requirements and approvals
F Allow a Provisional Sum of KShs 350,000 in
connection with environmental mitigation
measures including procurement, transport and
installation of items as directed by the Project
Manager. SUM
G Allow a Provisional Sum of KShs 2,500,000 in
connection with shifting and relocation of
services and utilities as directed by the Project
Manager. SUM
H Allow a Sum of KShs 1,040,000.00 in
connection with supervision as follows: 1 No.
Clerk of Works at Kshs. 10,000 per week SUM
J Allow a Sum of KShs 1,300,000 in connection
with payment of Resident Engineer's allowances
at Kshs. 12,500 per week SUM
K Allow a Provisional sum of kenya shillings for
ten million Kshs. 10,000,000.00 for Boundary
wall and fencing SUM
L Allow a Provisional sum of kenya shillings for
thirty million Kshs. 30,000,000.00 for civil
works SUM
TOTAL CARRIED TO SUMMARY
199
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
Transport
The contractor shall provide for site trips only a
vehicle of type Toyota or Nissan Van to
comfortably seat Nine persons including
maintaining licences and insurances, competent
driver; all to the satisfaction of the Project
Manager. The vehicle shall be provided
specifically for and during site visits by the
supervisory technical team. The vehicle shall be
in perfect conditions for the entire duration of the
trip i.e from Ministry of Roads, Transport and
PublicWorks head office situated at the county
works office building, Nakuru, off Nakuru -
Kabarak Road to Rift Valley Provincial General
Hospital and back to the office including local
running. The driver shall be at he sole direction
of the Project Manager for the entire duration of
the trip, until release by him/her (Total
approximate return journey is 10Km)
Reimbursement for the contractor for providing
the transport service driver, servicing, fuels, oils,
lubricants and tyres will be based per trip all at
the rate here below (Contractor to insert rate -
Item A inserted
A Allow for providing a vehicle as above described
including maintenance, fuels, lubricants spares
and tyres etc (one day) 208 Trips 6000
Carried to collection
COLLECTION
Brought forward from page 199
Brought forward from page 200 Above
TOTAL CARRIED TO SUMMARY
200
ITEM DESCRIPTION QTY UNIT RATE AMOUNT
PRIME COST SUMS
A Provide a Prime cost of Kenya shillings one
million Six hundred thousand
(Kshs. 1,600,000.00) for Lightning protection SUM
B Provide a Prime cost of Kenya shilling Nine
hundred thousand (Kshs. 900,000.00) for Fire
Detection and alarm system Sum
C Provide a Prime Cost of Kenya shillings Two
million, (Kshs. 2,000,000.00) only for external
security lighting Sum
D Provide a Prime Cost of Kenya shillings Three
million, (Kshs. 3,000,000.00) only for KP & LC
Ltd service line SUM
E Provide a Prime Cost Sum of Kenya shillings
Seventeen million (Kshs. 17,000,000.00) for IP
CCTV. Structured cabling and IP PABX
Installations SUM
F Provide a Prime Cost Sum of Kenya shillings Six
million (Kshs. 6,000,000.00) for Generator set
SUM
G Provide a Prime Cost Sum of Kenya shillings
Ten million (Kshs. 10,000,000.00) for high and
low level water tanks SUM
H Provide a Prime Cost sum of Kenya shillings
thirteen million (Kshs. 13,000,000.00) for
Medical gases SUM
TOTAL CARRIED TO SUMMARY
201
ITEM DESCRIPTION KSHS
SUMMARY
A PARTICULAR PRELIMINARIES
B GENERAL PREMINARIES
C TOTAL FOR GROUND FLOOR
D TOTAL FOR 1ST & 2ND FLOOR
E TOTAL FOR 3RD FLOOR
SUB-TOTAL
F TOTAL FOR PROVISIONAL SUMS
G TOTAL FOR PRIME COST SUM S
TOTAL CARRIED
TO FORM OF TENDER 16% V.A.T INCLUSIVE
Contract Period …………………………………………………80 weeks…………………
Amount in words …..……………..……………………………………………………….
…………………………………………………..………………………………………..
…….……………………………………………..……………………………………….
Tenderers Name ……………………………...………………………………………….
………….………………………………………………..……………………………….
Adress ……………………………………………………………………..……………….
………………………….………………………………………………..………………
Signature ………………………………..Date……………..……………………………….
………………………………… ………………………………………………………….
202
200
201
FROM PAGE
75
88
134
169
198
PROPOSED OUTPATIENT DEPARTMENT BLOCK AT RIFT
VALLEY PROVINCIAL GENERAL HOSPITAL NAKURU
top related