snap-on aluminum welding mhg5a owners manual
Post on 14-Nov-2015
119 Views
Preview:
DESCRIPTION
TRANSCRIPT
-
OWNER'S MANUALMHG5-A MIG GUN SYSTEM
THE MHG5-A"MOTORIZED HAND GUN" SYSTEMWITH THE SPEED CONTROL IN THE GUN HANDLE,REPRESENTS THE LATEST STATE OF THE ARTIN MIG EQUIPMENT FOR ALUMINUM WELDING.
MODEL NUMBER MHG5-A
FOR TECH. SERVICE, CALL TOLL-FREE 1-800-232-9353
FORM WC5385 Rev. 9/00
INSTALLATIONOPERATION
REPLACEMENT PARTS
-
MANUFACTURERS LIMITED WARRANTY
This equipment is warranted against defects in materials and workman-ship for a period of ninety (90) days from the date of purchase. Should itbecome defective for such reason, the Manufacturer will repair it withoutcharge, if it is returned to the Manufacturers factory, freight prepaid. Thiswarranty does not cover: (1) failure due to normal wear and tear; (2)consumable parts, such as, but not limited to, torch contact tips, gas cupsand insulating bushings; (3) damage by accident, force majeure, improperuse, neglect, unauthorized repair or alteration; (4) anyone other than theoriginal purchaser.
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRAN-TIES, EXPRESS OR IMPLIED. THE MANUFACTURER SHALL NOT BELIABLE FOR ANY INJURY TO PERSONS, INCLUDING DEATH; ORLOSS OR DAMAGE TO ANY PROPERTY, DIRECT OR CONSEQUEN-TIAL, INCLUDING, BUT NOT LIMITED TO, LOSS OF USE, ARISING OUTOF THE USE, OR THE INABILITY TO USE, THE PRODUCT. THE USERASSUMES ALL RISK AND LIABILITY WHATSOEVER IN CONNECTIONWITH THE USE OF THE PRODUCT, AND BEFORE DOING SO, SHALLDETERMINE ITS SUITABILITY FOR HIS INTENDED USE, AND SHALLASCERTAIN THE PROPER METHOD OF USING IT.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG ANIMPLIED WARRANTY LASTS, OR THE EXCLUSIONS OR LIMITATIONSOF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVELIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THISWARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAYHAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
Snap-on Tools Corporation Kenosha, WI 53141-1415
TABLE OF CONTENTSINTRODUCTION .............................................................1
SPECIFICATIONS, CHECK LIST ...................................3
OPTIONAL EXTRAS ......................................................4
CONSUMABLE PARTS..................................................5
INSTALLATION ..............................................................6
OPERATION .................................................................12
ELECTRICAL DIAGRAM ..............................................15
PARTS BREAKDOWN - GUN ......................................16
PARTS BREAKDOWN - CABLE ASSEMBLY .............18
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 1
INTRODUCTION
The Snap-On Tools MHG5-A is thelatest "State of the Art" in MIGspool guns for aluminum welding.The MHG5-A System is designed forGas Metal Arc Welding (GMAW or MIG)of aluminum material using .023",.030", .035" or 3/64" aluminum wirepackaged on 4 inch diameter spools.To weld steel, optional equipmentis required (see pages 4 and 5 - use.030" or .035" steel wire). Wirespeed is controlled by a diallocated in the gun handle.
ELEC-TRODE
WORK
MHG-5MOTORIZEDHAND GUN HGC5-25
HAND GUNCABLE ASSEMBLY
(INCLUDESPOWER PLUG)
POWER SOURCEFEEDROLLS
WIRE SPOOL
SHIELDING GAS
MIGGUN
WORK
+REVERSEPOLARITY
(STD.)
-
FIGURE 1. MHG5-A SYSTEM COMPONENTS
FIGURE 2. SCHEMATIC OF MIG PROCESS
FIGURE 3. SHORT ARC TRANSFER
The consumable electrode wireis melted and transferred to theweld puddle by any of three arcmodes; short arc transfer, globulartransfer, or spray arc transfer.The MHG5-A is capable of performingall modes, depending on the powersource being used.
SHORT ARC OR DIP TRANSFER
Short arc transfer occurs at 12to 22 arc volts (voltage whilewelding), depending on wire size.Welding commences as the arc isstruck and a weld pool is formed.The tip of the electrode wire dipsinto the pool and causes a shortcircuit. The short circuit currentflow causes a rapid temperaturerise in the electrode wire and theend of the wire is melted off. An arcis immediately formed between thetip of the wire and the weld pool,maintaining the electrical circuitand producing sufficient heat tokeep the weld pool fluid. Theelectrode continues to feed andagain dips into the pool.
The MHG5-A System is designedspecifically for operation withSnap-On Tools FM140A, M140i, YA204C,YA212A and YA212A "INDUSTRIAL" MIGCombination Units.
THE MIG PROCESSAS APPLIED TO THE MHG5-A
The MIG process uses a bare,consumable electrode in the form ofspooled wire, which is fed by acontrollable speed feed unit throughthe gun barrel to the weld. Theemerging wire and the weld areshielded by a stream of Argon gaswhich prevents oxidation of themolten weld puddle. Aluminum is MIGwelded with reverse polarity [elec-trode positive (+)]. In this mode,the electrons move from the work tothe electrode (welding wire) caus-ing a cathode cleaning effect of theweld area.
-
2 Snap-on Tools Corporation Kenosha, WI 53141-1415
In short arc transfer, thesequence of events is repeated up to200 times per second. Short arc issuitable for positional welding.The heat input to the workpiece iskept to a minimum which limitsdistortion and makes possible thewelding of thin sheet material.
GLOBULAR TRANSFER
Globular transfer occurs at theintermediate range of 22 to 24 arcvolts, depending on wire size. Asthe name implies, the transfertakes place in the form of irregu-larly shaped globules. Globulartransfer is useful in cases where alower heat input than that of truespray is required.
DESCRIPTION
The MHG5-A consists of the gunand the gun cable assembly.
The Motorized Hand Gun (MHG-5)used on the MHG5-A System is thelatest model. It incorporates thefollowing features.
SPRAY TRANSFER
Spray transfer occurs at 22 to28 arc volts, depending on wiresize. The length of the arc is heldconstant by the voltage available.The higher voltage and currentcauses the electrode wire to meltoff before touching the workpiece.The molten metal crosses the gap tothe workpiece in a spray form.Spray transfer is used in the down-hand position and provides higherdeposition rates than short arctransfer or globular transfer.
GAS NOZZLE
WORKSHIELDING GAS
ELECTRODE
WORK
ELECTRODE
SHIELDING GAS
GAS NOZZLE
OFFSET
WIREBURNBACK
THE TIP END IS NOTCHED AND OFFSETFOR MAXIMUM ELECTRICAL TRANSFER.IF THE WIRE BURNS BACK TO THE TIP, THE"BALL" FORMED CAN BE PEELED AWAY ANDGENERALLY, THE TIP CAN STILL BE USED.
CONSTANT PRESSURE,CLEAR GUN COVER NON-ADJUSTABLE(AND SPOOL COVER) FEED ROLL SYSTEM
ONE DRIVE ROLL COMBINATIONFOR ALL WIRE SIZES WELD CABLE &.023", .030", .035", 3/64" GAS HOSE
TWO FINGER CABLETRIGGER FITTING
- FOR EASYATTACHMENT
ROLL RELEASE OF GUNLEVER CABLE- DRIVE ROLLPRESSURE REMOTERELEASE FOR SPEED CONTROLPURGING AND POTENTIOMETERWIRE THREADING IN HANDLE
FIGURE 4. GLOBULAR TRANSFER
FIGURE 5. SPRAY TRANSFER
FIGURE 7. SPECIAL FEATURES OFMG-T25, MG-T30, MG-T35 & MG-T364
NOTCHED END CONTACT TIPS
FIGURE 6. SPOOL GUN FEATURES
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 3
14-1/2"
6-1/2"
GUNENDFITTINGS
CONTROLCABLE
CONTROL CABLEPLUG
PS-4APOWER WELD CABLEPLUG / GAS HOSE
The Power Plug (PS-4A) (in-stalled on the Weld Cable/Gas Hose)plugs directly into the "TorchStandard" terminal on the frontpanel of the welding machine. TheWeld Cable/Gas Hose carries thewelding current and shielding gas.Gas flow is controlled by the gassolenoid in the welding machine.
The Control Cable plugs into thefunction receptacle in the weldingmachine. It carries power to the gunmotor and returns the contactoractuation signal to the weldingmachine.
SPECIFICATIONS
PART NUMBER: MHG5-A
AMPERAGE RATING:- 60% Duty Cycle 250 Amps- 100% Duty Cycle 200 Amps
SPECIFICATIONS (Cont.)
DUTY CYCLE TIME PERIOD:10 minutes
WIRE TYPE: aluminum, steel
WIRE SIZES: .023", .025", .030",.035", 3/64" aluminum
.030" - .035" steel
WIRE FEED SPEED RANGE:50 - 650 inches per minute
SHIELDING GAS:For Aluminum 100% ArgonFor Steel 75% Argon + 25% CO2
WEIGHT:- Gun 2-3/4 pounds- Gun and Cable 14 pounds
DIMENSIONS:See Illustration
CHECK LIST
THE SNAP-ON TOOLS MHG5-A SYSTEMINCLUDES THE FOLLOWING:
1- MHG-5 Spool Gun
1- HGC5-25 Hand Gun Cable Assem-bly - 25 foot
1- PS-4A Power Plug (installed ongun cable assembly)
7- MG-TXX Contact Tip (one in-stalled in gun)
1- M35-NA62 Nozzle Assembly (in-stalled on gun)
1- M35-D Gas Diffuser (installedin gun)
1- 4043-XX Spool of Aluminum Wire
FIGURE 8. CABLE ASSEMBLY
DESCRIPTION (Cont.)
The Hand Gun Cable Assembly(HGC5-25) consists of (1) a concen-tric Weld Cable/Gas Hose with fit-tings and Power Plug, and (2) aControl Cable with fittings. Thestandard cable assembly is 25 feetlong. 35 foot (HGC5-35) and 50 foot(HGC5-50) assemblies are extra costoptions.
-
4 Snap-on Tools Corporation Kenosha, WI 53141-1415
OPTIONAL EXTRAS(designate when ordering spool gun)
Example: MHG5-A w/HGC5-50
HGC5-35 35 foot Gun Cable Assem-bly
HGC5-50 50 foot Gun Cable Assem-bly
MG-T25 .023" - .025" Notched EndContact Tip - for alumi-num welding.
MG-T30 .030" Notched End Con-tact Tip - for aluminumwelding.
MG-T35 .035" Notched End Con-tact Tip - for aluminumwelding.
MG-T364 3/64" Notched End Con-tact Tip - for aluminumwelding.
4043-23 .023" type 4043 AluminumWelding Wire on 4 inchspool
4043-30 .030" type 4043 AluminumWelding Wire on 4 inchspool
4043-35 .035" type 4043 AluminumWelding Wire on 4 inchspool
4043-364 3/64" type 4043 AluminumWelding Wire on 4 inchspool
MG-CBA-60 60 degree Curved BarrelAssembly
MG-CBA-45 45 degree Curved BarrelAssembly
MG-FBA Flexible Barrel Assembly
GR-FM Argon Gas Regulator andFlowmeter
OPTIONS FOR WELDING STEEL (ANDOTHER HARD WIRES - STAINLESS STEEL,BRONZE, ETC.)
SN-2160K Knurled Drive Roll - forfeeding steel wire.
M5-T25 .023" - .025" Contact Tip- for steel welding.
M5-T30 .030" Contact Tip - forsteel welding.
M5-T35 .035" Contact Tip - forsteel welding.
See the "FRONT END CONSUMABLEPARTS" chart on the following pagefor a complete listing of availablenozzles, contact tips, etc. foraluminum welding and for steelwelding.
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 5
FRONT END CONSUMABLE PARTS
HEAVY DUTY FIXED NOZZLE FRONT END
APPL. NOZZLE, NOZZLE ASSEMBLY CONTACT TIP GAS DIFFUSER
FIXED NOZZLE FRONT END
APPL. NOZZLE, NOZZLE ASSEMBLY CONTACT TIP GAS DIFFUSER
ADJUSTABLE NOZZLE FRONT END
APPL. NOZZLE INSULATOR CONTACT TIP GAS DIFFUSER
M3-T25 (.025)M3-T30 (.030)M3-T35 (.035)M3-T45 (.045)M3-ST25 (.025)M3-ST30 (.030)M3-ST35 (.035)M3-ST45 (.045)
M3T-D
MG-T25 (.023-.025)MG-T30 (.030)MG-T35 (.035)MG-T364 (3/64)
M5-T25 (.025)M5-T30 (.030)M5-T35 (.035)M5-T45 (.045)M5-LT25 (.025)M5-LT30 (.030)M5-LT35 (.035)M5-LT45 (.045)M3-T25 (.025)M3-T30 (.030)M3-T35 (.035)M3-T45 (.045)M3-ST25 (.025)M3-ST30 (.030)M3-ST35 (.035)M3-ST45 (.045)
M3-D
M35-D
M35-HD- FORM5-HT
SERIES TIP
MG-T25 (.023-.025)MG-T30 (.030)MG-T35 (.035)MG-T364 (3/64)
M5-T25 (.025)M5-T30 (.030)M5-T35 (.035)M5-T45 (.045)
M5-HT45 (.045)
M5-BINSULATINGBUSHING
M5H-NB M5H-B M5H-NNBODY BUSHING NUT
M5-NB BODY
M35H-NA62
M35-NA62
M5-C625/8" CUP
M5-C753/4" CUP
M5-C625/8" CUP
M5-C753/4" CUP
M3-C50L1/2" CUP- LONG
M3-C50XL1/2" CUP- EXTRA LONG
M3-C501/2" CUP
M3-C625/8" CUP
M5-C625/8" CUP
M5-C753/4" CUP
M3-BINSULATINGBUSHING
M3-NB BODY
M3X-NB M3H-B M3H-NNBODY BUSHING NUT
M3-BINSULATINGBUSHING
M3-NB BODY
USE M3-C50XL CUP WITHM5-LT SERIES CONTACT TIPS
M3-NA50
M3X-NA62
M3T-N501/2" NOZZLE
M3T-N753/4" NOZZLE
M3T-B(INCLUDESO-RINGS)
M3T-BRO-RING(3 REQD.)
STEE
L*W
ELD
ING
STEE
L*A
LUM
INU
MW
ELD
ING
WEL
DIN
GST
EEL*
ALU
MIN
UM
WEL
DIN
GW
ELD
ING
PREFERRED ALTERNATE FRONT END
STANDARD EQUIPMENT FRONT END
*SN-2160K-KNURLED DRIVE ROLL IS REQUIRED FOR STEEL WELDING
-
6 Snap-on Tools Corporation Kenosha, WI 53141-1415
NOTEThe MIG Combination Unit musthave either (1) BULKHEAD FIT-TINGS and SELECTOR HOSE (cur-rent model welders) or (2)TOGGLE VALVE ASSEMBLY (factoryinstalled or TV-5A Kit - de-pending on welder model andserial number). This sectioncontains installation instruc-tions for both types. The weld-ers covered by each set ofinstructions are identified bymodel number and serial numberat the beginning of the in-structions. Be sure to followthe correct set of instruc-tions.
CONNECTING THE GUN TO A MIG UNITWITH BULKHEAD GAS FITTINGS / SELEC-TOR HOSE SYSTEM (See Figures 9 & 10)
All current model Snap-On ToolsMIG Combination Units are equippedwith bulkhead gas fittings forquick and easy change-over to spoolgun operation using the MHG5-A Gun.The following MIG Units have thissystem.
FM140A (serial nos. 840-6072and later),
M140i (serial nos. 940i-2180and later).
YA204C (serial nos. 804-2325and later),
YA212A (serial nos. 812-4121and later),
YA212A INDUSTRIAL (serial nos.812I-6747 and later),
1. Open the access door of the MIGCombination Unit.
2. Remove the thread cap from thebulkhead fitting marked "SPOOLGUN".
ITEMS REQUIRED FOR MIG WELDINGWHICH ARE NOT PROVIDED WITH THEMHG5-A SYSTEM
1. DC welding machine
NOTEThe MHG5-A System operateswith the following Snap-OnTools MIG Combination UnitsONLY: FM140A (serial nos.840-500 through 840-790 and840-2000 and later), M140i(all), YA204C (serial nos.804-2123 and later), YA212A(serial nos. 812-2625 andlater), YA212A INDUSTRIAL(serial nos. 812I-3227 andlater).
2. Full cover welding helmet withproper colored lens (shade 10 ordarker).
3. Pure Argon gas and cylinder (or75% Argon + 25% CO2 for weldingsteel).
4. Argon gas regulator (availableas an optional extra).
5. Leather welding gloves.
6. Ground cable and clamp.
INSTALLATIONThe MHG5-A System operates with
the following Snap-On Tools MIGCombination Units ONLY:
FM140A (serial nos. 840-501through 840-790 and840-2000 and later),
M140i (all).YA204C (serial nos. 804-2123
and later),YA212A (serial nos. 812-2625
and later),YA212A INDUSTRIAL (serial nos.
812I-3227 and later),(continued on following page)
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 7
CONNECTING THE GUN TO A MIG UNITWITH BULKHEAD GAS FITTINGS / SELEC-TOR HOSE SYSTEM (Cont.)
3. Unscrew the selector hose fromthe "MIG TORCH" bulkhead fit-ting.
4. Move the selector hose to the"SPOOL GUN" fitting and tightenit.
5. Install the thread cap (removedin step 2) on the "MIG TORCH"fitting to prevent dirt andother contaminants from enter-ing the unused line.
6. Disconnect the MIG Unit's wiredrive motor by removing the wirefeed motor plug from the func-tion receptacle.
7. Plug the spool gun control cableplug into the MIG Unit's func-tion receptacle.
8. Remove the torch selector cablefrom the positive (+) terminalon the front panel of the MIGUnit. Allow the torch selectorcable to hang free. Make surethe ground cable is plugged intothe negative (-) terminal.
9. Plug the spool gun power plug (onthe end of the welding cable /gas hose) into the positive (+)terminal.
NOTETo change back to standardMIG torch operation, re-verse the procedure andchange the shielding gas.
SPOOL GUN CONTROL CABLE PLUGWIRE FEED MOTOR PLUG (PLUG INTO FUNCTION RECEPTACLE)(DISCONNECT FROMFUNCTION RECEPTACLE) SELECTOR HOSE
(MOVE TO "SPOOL GUN"MHG-5 GUN BULKHEAD FITTING)
HGC5-25 MIG COMBINATION UNITGUN CABLE (ACCESS DOOR OPEN)ASSEMBLY TORCH
SELECTOR CABLE GUN CABLE(REMOVE FROM (PLUG INTO+ TERMINAL) + TERMINAL)
FIGURE 9. CONNECTION DIAGRAM - FOR FM140-A & M140i MIG COMBINATION UNITS
WIRE FEED MOTOR PLUG SPOOL GUN CONTROL CABLE PLUG(DISCONNECT FROM (PLUG INTO FUNCTION RECEPTACLE)FUNCTION RECEPTACLE)
TORCH MIG COMBINATION UNITSELECTOR CABLE (ACCESS DOOR OPEN)(REMOVE FROM
MHG-5 GUN + TERMINAL)
SELECTOR HOSEHGC5-25 GUN CABLE (MOVE TO "SPOOL GUN"GUN CABLE (PLUG INTO BULKHEAD FITTING)ASSEMBLY + TERMINAL)
FIGURE 10. CONNECTION DIAGRAM - FOR YA204C, YA212A, YA212A INDUSTRIAL MIG UNITS
-
8 Snap-on Tools Corporation Kenosha, WI 53141-1415
CONNECTING THE GUN TO A MIG UNITWITH A GAS TOGGLE VALVE. (SeeFigures 11 and 12)
The following MIG CombinationUnits have a factory installedtoggle valve.
YA204C (serial nos. 804-2123through 804-2324),
YA212A (serial nos. 812-2625through 812-4120),
YA212A INDUSTRIAL (serial nos.812I-3227 through 812I-6746).
The following MIG CombinationUnits require the installation of aTV-5A Toggle Valve Kit prior toconnecting the spool gun.
FM140A (serial nos. 840-500through 840-790 and840-2000 through840-6071),
M140i (serial nos. 84i-2111through 84i-2130 and940i-2000 through940i-2179).
SPOOL GUN CONTROL CABLE PLUGWIRE FEED MOTOR PLUG (PLUG INTO FUNCTION RECEPTACLE)(DISCONNECT FROMFUNCTION RECEPTACLE) TOGGLE VALVE
(SWITCH TO "MHG5-A")MHG-5 GUN
HGC5-25 MIG COMBINATION UNITGUN CABLE (ACCESS DOOR OPEN)ASSEMBLY TORCH
SELECTOR CABLE GUN CABLE(REMOVE FROM (PLUG INTO+ TERMINAL) + TERMINAL)
MHG5-A
FIGURE 11. CONNECTION DIAGRAM - FOR FM140-A & M140i MIG COMBINATION UNITS
WIRE FEED MOTOR PLUG SPOOL GUN CONTROL CABLE PLUG(DISCONNECT FROM (PLUG INTO FUNCTION RECEPTACLE)FUNCTION RECEPTACLE)
TORCH MIG COMBINATION UNITSELECTOR CABLE (ACCESS DOOR OPEN)(REMOVE FROM
MHG-5 GUN + TERMINAL)
TOGGLE VALVEHGC5-25 GUN CABLE (SWITCH TO "MHG5-A")GUN CABLE (PLUG INTOASSEMBLY + TERMINAL)
MHG5-A
FIGURE 12. CONNECTION DIAGRAM - FOR YA204C, YA212A, YA212A INDUSTRIAL MIG UNITS
(continued on following page)
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 9
1. Place a cylinder of the appro-priate shielding gas in the rackat the rear of the weldingmachine and secure it with thechain provided.
2. Rapidly open and close the cyl-inder valve. This will purgedust and foreign matter from thevalve.
Take care to point the valveoutlet away from yourself orother people, as escapinghigh pressure gas may bedangerous.
3. Attach a gas regulator - flowme-ter to the cylinder valve usinga suitable wrench.
4. Fit the gas hose from the welderto the regulator outlet fittingand tighten it with a wrench.Open the cylinder valve.
5. Check that the gas regulator isproperly adjusted. When weldingaluminum, the gas flow rate is 40CFH. When welding steel, the gasflow rate is 30 CFH.
NOTEThe Welding machine must beturned "ON" and the MHG5-Atrigger depressed, beforethe gas flow rate can beadjusted.
FITTING THE ELECTRODE WIRE
1. Remove the gun cover, spoolcover, nozzle assembly and con-tact tip. Remove the spool brakeassembly from the spool spindleand place a 4 inch spool ofwelding wire on the spindle.
CONNECTING THE GUN TO A MIG UNITWITH A GAS TOGGLE VALVE. (Cont.)
1. Open the access door of the MIGCombination Unit.
2. Disconnect the wire drive motorby removing the wire feed motorplug from the function recep-tacle.
3. Plug the spool gun control cableplug into the welder functionreceptacle.
4. Remove the torch selector cablefrom the positive (+) terminalon the front panel of the weldingmachine. Allow the torch selec-tor cable to hang free. Make surethe ground cable is plugged intothe negative (-) terminal.
5. Plug the spool gun power plug (onthe end of the welding cable /gas hose) into the positive (+)terminal.
6. Switch the toggle valve insidethe machine from the "MIG" set-ting to the "MHG5-A" setting.This redirects the gas flow fromthe wire drive assembly to thepositive (+) terminal.
NOTETo change back to standardMIG torch operation, re-verse the procedure andchange the shielding gas.
SHIELDING GAS CONNECTIONS
NOTEMake sure the welder primarygas hose and regulator/flowmeter are connected to acylinder of the propershielding gas - 100% Argonfor aluminum and 98% Argon +2% O2 for stainless steeland 75% Argon + 25% CO2 forsteel welding.
CAUTION
(continued on following page)
-
10 Snap-on Tools Corporation Kenosha, WI 53141-1415
FITTING THE ELECTRODE WIRE(Cont.) SPOOL BRAKE ADJUSTMENT
The specifications for the 4inch spool allow a variation in thewidth of the spool of up to 1/16 inch(1/32 inch tolerance). The spoolbrake spring will handle most spoolwidth variations. The followingadjustments can be made if re-quired.
If the spool brake is not applyingenough tension on the spool:
1. Remove the spool brake assemblyand the spool of wire.
2. Remove the spool hub nut and thelock washer.
3. Remove shim washer(s) as needed.
4. Remove the spool hub bolt andplace the removed shimwasher(s) under the bolt head.
5. Reassemble all components ex-cept for the spool cover.
SPOOL COVER
SPOOL BRAKEASSEMBLY
LOCK WASHER SPOOL HUB NUT
SHIM WASHERS
SHIM WASHER
LOCK WASHER
SPOOL HUB BOLT
FIGURE 15. INCREASINGBRAKE TENSION ON THE SPOOLFIGURE 14. SPOOL BRAKE ASSEMBLY
HAND NUT
BRAKE SPRING
BRASS WASHER
SPOOL WASHER (NYLON) SNAP RING
2. Replace the spool brake assem-bly.
NOTEThe spool brake assemblymust bottom out against thespool hub nut when installed.The spring in the spoolbrake assembly provides theproper tension on the wirespool.
FIGURE 13. SPOOL GUN COMPONENTS
CONTACTTIP
TRIGGER
SPEED DRIVE ROLL LEVERCONTROL (PUSH UP TO OPENKNOB DRIVE ROLLS)
SPOOLBRAKEASSY.
SPOOLSPIN-DLE
NOZZLE GUN SPOOL COVERASSEMBLY COVER
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 11
If the spool brake is applying toomuch tension on the spool:
1. Remove the spool brake assemblyand the spool of wire.
2. Remove the spool hub nut and thelock washer.
3. Remove the spool hub bolt.
4. Remove shim washer(s) as neededfrom under the bolt head.
5. Place the removed shim washer(s)under the spool hub nut.
6. Reassemble all components ex-cept for the spool cover.
THREADING THE ELECTRODE WIRE
1. Make sure the feed roll isproperly installed to match thewire size.
To change the feed roll setting:
a. Loosen but do not remove thesetscrew.
b. Slide the feed roll off themotor shaft.
c. Turn the feed roll over andreinstall it on the motorshaft.
d. Tighten the setscrew se-curely.
2. Set the welding machine WIRESPEED control to "10" to providefull range speed control at theMHG-5 spool gun.
3. Turn the wire feed control in thespool gun handle clockwise tothe maximum setting.
4. Turn on the welding machine tosupply power to the gun. Openthe rolls on the gun by pushingthe Drive Roll Lever up.
5. Thread the wire through theinlet guide, between the feedand pressure rolls and into thebarrel liner. The wire must bestraight when it is threaded.
(continued on following page)
SPOOL COVER
SPOOL BRAKEASSEMBLY
LOCK WASHER SPOOL HUB NUT
SHIM WASHERS
SHIM WASHER
LOCK WASHER
SPOOL HUB BOLT
FIGURE 17. FEED ROLL
SMALLGROOVE FOR.025" - .035" WIRE
LARGE SETSCREWGROOVE FOR3/64" WIRE
FIGURE 16. DECREASINGBRAKE TENSION ON THE SPOOL
-
12 Snap-on Tools Corporation Kenosha, WI 53141-1415
4. Turn the Speed Control Knob inthe bottom of the gun handleclockwise to the maximum set-ting.
5. With the proper hood, gloves andother protective equipment inplace, locate the gun over thejoint to be welded and bring thenozzle to 1/2 to 5/8 inch fromthe workpiece. The recommendedposition of the gun and direc-tion of travel for welding alu-minum are shown in Figure 19.
THREADING THE ELECTRODE WIRE(Cont.)
6. Release the drive roll lever andpull the gun trigger. Wire willbe pushed out the front of thegun. Run out approximately 6inches of wire. Reinstall thecontact tip, nozzle assembly,gun cover and spool cover.
7. Cut off the electrode wire evenwith the front of the nozzleassembly.
8. Actuate the drive roll lever toopen the rolls and pull the guntrigger to purge the system ofcontaminants. Purge for two min-utes. Release the trigger andthe drive roll lever.
YOU ARE NOW READY TO WELD
OPERATION1. Attach the WORK (ground) cable
from the negative (-) terminalon the welding machine to a CLEANspot on the material to bewelded.
2. Set the HEAT (voltage) controlon the welding machine to thedesired setting.
3. Set the WIRE SPEED control on thewelding machine to "10".
10 DEGREES
DIRECTIONOF TRAVEL
WORK
SHIELDING GAS
6. Actuate the gun trigger. Theshielding gas will flow, thewelding wire will advance and anarc will be formed. Adjust theSpeed Control Knob in the gunhandle to obtain the correct arccharacteristics. As the weld isdeposited, move the gun slowlyalong the weld seam at a constantspeed, while maintaining a con-stant arc length and a constanttip-to-work distance.
7. Refer to the "RECOMMENDED WELD-ING VALUES" charts on the fol-lowing pages for recommended arcvoltage, wire speed, etc.FIGURE 18. SPEED CONTROL KNOB
INCREASEWIRE SPEED
DECREASEWIRE SPEED
FIGURE 19.TORCH POSITION FOR WELDING ALUMINUM
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 13
RECOMMENDED WELDING VALUES
SHORT ARC TRANSFER
METAL AMPS WIRE WIRE WELDTHICKNESS (DCRP) SIZE SPEED SPEED
.040" 40 .030" 240 IPM 20 IPM
.050" 50 .030" 290 IPM 15 IPM
.063" 60 .030" 340 IPM 15 IPM
.093" 90 .030" 410 IPM 15 IPM
.040" 40 .035" 200 IPM 24 IPM
.050" 50 .035" 240 IPM 18 IPM
.063" 60 .035" 290 IPM 18 IPM
.093" 90 .035" 350 IPM 18 IPM
SPRAY ARC TRANSFER
METAL JOINT AMPS WIRE ARC WIRETHICK. PREP. (DCRP) SIZE VOLTS SPEED
1/8" Type A 100 .030 24-26 450 IPM3/16" Type B 150 .030" 24-26 500 IPM1/4" Type B 180 .030" 28-29 560 IPM3/8" Type C 200 .030" 28-30 600 IPM
1/8" Type A 100 .035" 24-26 400 IPM3/16" Type B 150 .035" 24-26 450 IPM1/4" Type B 180 .035" 28-29 530 IPM3/8" Type C 200 .035" 26-30 560 IPM1/2" Type C 220 .035" 26-30 600 IPM
1/8" Type A 110 3/64" 20-21* 175 IPM3/16" Type B 160 3/64" 20-21* 220 IPM1/4" Type B 180 3/64" 27-28 250 IPM3/8" Type C 200 3/64" 25-30 260 IPM1/2" Type C 220 3/64" 25-31 270 IPM3/4" Type C 250 3/64" 25-31 290 IPM
* SHORT ARC TRANSFER
DETAILS OF JOINT PREPARATION(see "Spray Arc Transfer" chart above)
60o - FLAT POSITION90o - HORIZONTAL OR
VERTICAL POSITION110o - OVERHEAD POSITION
0" TO 3/16"1/16"0" TO 1/8"
0" TO 3/16"1/16"
90o
90o
TYPE A TYPE B
TYPE C
STAINLESS STEELOR MILD STEEL
-
14 Snap-on Tools Corporation Kenosha, WI 53141-1415
SHIELDING GAS PERFORMANCE
SHIELDINGPROCESS GAS PERFORMANCE
Gas Metal Argon Best Metal TransferArc Welding(GMAW or Excellent Arc StabilityMIG)
Excellent CleaningAction
Low Spatter
Helium Deep Penetration- for heavy plate
SHIELDING GAS FLOW RATES
MATERIAL WELDING FLOWTHICKNESS POSITION RATES
1/16 in. Flat 25 CFHFlat, Vertical,3/32 - 1/8 in. 30 CFHHorizontal, OverheadFlat, Vertical,3/16 in. 30 CFHHorizontal, OverheadFlat 30 CFH
1/4 in. Vertical, Horizontal 35 CFHOverhead 40 CFHFlat 30 CFH
3/8 in. Vertical, Horizontal 35 CFHOverhead 40 CFHFlat 35 CFH
3/4 in. Vertical, Horizontal, 40 CFHOverhead
RECOMMENDED WELDING VALUES (Cont.)
RECOMMENDED FILLER METALS CHART
Base 6061, 5083, 5454 5154 5086 5052 5005, 3004 2219 1100, 1060,Metal 6063, 5456 5050 & 3003 1350
6101, Alclad &6151, 3004 Alclad
Base 6201, 3003Metal 63511060, 1100 1100 11004043 5356 4043 4043 5356 4043 4043 41451350 4043 4043 40431100, 4043 4043 4043 4043 4043 11003003, 4043 5356 4043 41455356 5356 5356 5356 5356 4043Alclad 3003
23192219 4043 4043 4043 4043 4043 4043 4043 4043 40433004, 4043 5356 5356 4043 4043 40435356 5356Alclad 3004 5356 5654 5654 5356 5356 53565005, 4043 5356 5356 4043 40435356 53565050 5356 5654 5654 5356 5356
4043 5356 5356 40435052 5356 53565356 5654 5654 56545356 53565086 5356 5356 53565654 5654
4043 5356 5356 53565154 5356 5654 5654 56544043 53565454 55545356 5654
5083, 5356 555654566061, 6063, 40436101, 6151, 53566201, 6351
NOTES: 1. 5183 or 5356 may be used in place of 5556.2. 5183, 5356, 5554 or 5556 may be used in place of 5654.3. 5183 or 5556 may be used in place of 5356.
RECOMMENDEDFILLER WIRE
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 15
GUN CABLE
RED
BLACK
WHITE
BLUE
ORANGE
GREEN
+
-
ELECTRICAL DIAGRAM
MHG5-A SPOOL GUN SYSTEM
GUNCABLEFUNCTIONPLUG
WELDINGMACHINE
FEED MOTORFUNCTION
RECEPTACLE
GUNCABLEPLUG
SPOOLGUNRECEPTACLE
GUN MOTOR
DC VOLTAGE
WIRE SPEEDCONTROL
TORCHTRIGGER
1
2
3
4
5
6
1
2
3
4
5
6N.O.
N.C.
- +
RED
BLACK
GRAY
GRAY
PURPLE / WHITE
PURPLE / WHITE
SPEEDCONTROLPOTENTIOMETER
SPOOL GUNTRIGGER
-
16 Snap-on Tools Corporation Kenosha, WI 53141-1415
SN-2514
SN-2514
SN-2413M
SN-2109M
SN-2129T-3 SN-574S
M3-214M
SN-2515
SN-217
SN-2119
SN-2118
SN-2133T
SN-2410B
SN-2420
SN-2416A
SN-2146C
SN-215A
SN-2567
SN-2520S
SN-2514
SN-2160 (FOR ALUM.)SN-2160K (FOR STEEL) (OPT.)
SN-2516
SN-324S
SN-2114B
SN-2147M
SN-2148
SN-2148
SN-2158
SN-2410C
SN-2149B
SN-2114C
SN-2419CA
SN-5
SN-2134R
SN-2416
SN-216B
SN-2121C
SN-2121BSN-2514A
SN-019M4
SN-2394M
SN-2412M
SN-2145M3
SN-2517SN-2518
SN-2517SN-2419CSN-2391M6
SN-2399-6
NOTE: SEE PAGE 5FOR FRONT ENDCONSUMABLE PARTS(NOZZLES, INSULATORS,CONTACT TIPS, ETC.)
REPLACEMENT PARTS - MHG-5 GUN
-
Snap-on Tools Corporation Kenosha, WI 53141-1415 17
PART NO. DESCRIPTION
M3-214M TRIGGER SPRING
SN-5 CABLE CLIP - H. H. SMITH 780
*ATTACHING HARDWARE*
8-32 X 3/8" RND. HD. SCREW (1)
SN-019M4 SWITCH - WIRED
SN-215A SPOOL SPINDLE
*ATTACHING HARDWARE*
1/4-20 X 3" HEX HD. BOLT (1)1/4" INTERNAL TOOTH
LOCK WASHER (2)1/4" FLAT WASHER (1)1/4" SPRING (SHIM) WASHER (3)7/16" STEEL WASHER (1)1/4-20 JAM NUT (1)
SN-217 HAND NUT - SPOOL COVER
SN-324S POTENTIOMETER - 100K- WITH ATTACHING NUT
SN-2109M HAND NUT - TOP COVER
SN-2114B ROLL BLOCK BUSHING
SN-2114C ROLL LEVER BUSHING
SN-2118 SPOOL DISC
*ATTACHING HARDWARE*
8-32 X 1/2" RND. HD. SCREW (1)8-32 KEP NUT (1)
SN-2119 SPOOL COVER
SN-2133T INLET GUIDE TUBE
*ATTACHING HARDWARE*
8-32 X 1/4" NYLOC SET SCREW(1)
SN-2134R REEL SUPPORT
*ATTACHING HARDWARE*
1/4-20 X 1/4" SET SCREW (1)
SN-2145M3 HANDLE
*ATTACHING HARDWARE*(HANDLE AND BASE TO BODY BLOCK)
8-32 X 3/4" RND. HD. SCREW (2)8-32 X 1-1/4" RND. HD. SCREW (2)
SN-2146C MOTOR (BOTTOM TERMINALS)
*ATTACHING HARDWARE*(MOTOR TO BODY BLOCK)
4-40 X 3/8" FLAT HD. SCREW (3)
SN-2147M ROLL BLOCK
*ATTACHING HARDWARE*
8-32 X 1/2" FLAT HD. SCREW (1)
SN-2148 PRESSURE ROLL SPACER (2 REQD.)
PART NO. DESCRIPTION
SN-2149B SPRING - ROLL PRESSURE
*ATTACHING HARDWARE*
4-40 X 1/4" RND. HD. SCREW (2)
SN-2158 PRESSURE ROLL
SN-2160 FEED ROLL (FOR ALUMNIUM)
*ATTACHING HARDWARE*
8-32 X 1/8" SET SCREW (1)
SN-2160K KNURLED FEED ROLL (FOR STEEL)(OPTIONAL)
*ATTACHING HARDWARE*
8-32 X 1/8" SET SCREW (1)
SN-2399-6 6 PIN RECEPTACLE
SN-2391M6 MOULDED BASE
SN-2394M TRIGGER
SN-2410B SPOOL INSULATOR BUSHING
SN-2410C PRESSURE ROLL BUSHING
*ATTACHING HARDWARE*
8-32 X 3/8" FLAT HD. SCREW (1)
SN-2412M BODY BLOCK
SN-2413M TOP COVER
SN-2416A SPOOL BRAKE ASSEMBLY
CONSISTING OF:
SN-2416 HAND NUT
SN-216B SPRING BRAKE
SN-2121C BRASS WASHER - 3/8"
SN-2121B SPOOL WASHER
SN-2514A SNAP RING - 3/8"
SN-2419CA BARREL ASSEMBLY
CONSISTING OF:
SN-574S O-RING - BARREL LINER
SN-2129T-3 BARREL LINER - TEFLON
SN-2419C BARREL
SN-2516 BARREL OUTER SLEEVE
SN-2517 SPACER/SEAL (2 REQUIRED)
SN-2518 BARREL INSULATOR SHEATH
SN-2420 LEVER - ROLL RELEASE
*ATTACHING HARDWARE*
8-32 X 3/8" FLAT HD. SCREW (1)
SN-2514 SNAP RING - 5/8" (3 REQUIRED)
SN-2515 RETAINING CLIP - SWITCH
SN-2520S CONTROL KNOB
SN-2567 SPEED INDICATOR DIAL
REPLACEMENT PARTS - MHG-5 GUN (Cont.)
-
18 Snap-on Tools Corporation Kenosha, WI 53141-1415
REPLACEMENT PARTS - HGC5-25 GUN CABLE ASSEMBLY
SN-2179-5
SN-862SN-863
SN-807G
PS-4A
SN-2157
SN-027-25SN-023SN-028
SN-2400-6
SN-2401
SN-2179-5
TOMOTORIZEDHAND GUN
SN-2622-25
SN-2157
SN-025 SN-026SN-028 SN-023
SN-027-25
SN-860 SN-860M
SN-2622-25
SN-860C
PART NO. DESCRIPTION
PS-4A POWER PLUG
SN-807G BOOT/CABLE COVER
SN-2008 CABLE TIE (AS REQUIRED)
SN-2157 CABLE AND HOSE ASSEMBLYWITH FITTINGS - 25 FOOT
CONSISTING OF:
SN-023 WELD CABLE (ONLY) (24'-10")
SN-025 CABLE FITTING
SN-026 GAS HOSE NUT
SN-027-25 GAS HOSE (ONLY)SAE100R6FW-27W (3/8"I.D. X 25')
SN-028 HOSE FERRULE (2 REQUIRED)
SN-2401 CABLE FITTING
PART NO. DESCRIPTION
SN-2179-5 CONTROL CABLE ASSEMBLYWITH FITTINGS - 25 FOOT
CONSISTING OF:
SN-860C PLUG ASSEMBLY
CONSISTING OF:
SN-860 HOUSING
SN-860M MALE PINS (6 REQUIRED)
SN-862 STRAIN RELIEF - WITH SCREW
SN-863 GROMMET
SN-2400-6 6 SOCKET PLUG
SN-2622-25 POWER CORD (ONLY)20-6 ALPHA (25'-6")
TO WELDERPOSITIVE (+) TERMINAL
TO WELDERFUNCTION RECEPTACLE
SN-2008
top related