solid hdpe plastic lockers royal lockers...z locker two tier z style athletic locker open style with...
Post on 20-Aug-2020
1 Views
Preview:
TRANSCRIPT
Solid HDPE Plastic Lockers
ROYAL LOCKERS
STANDARD CONFIGURATIONS AND OPTIONS
Never needs painting, 10 standard colors
Impervious to moisture and cleaners
Full Plastic Hinge and Strike
Vandal resistant welded construction
Wide range of sizes and configurations
ADA compliant
SIZE‐TIER OPTIONS
Standard:
HEIGHT WIDTH DEPTH Tiers 24 12”,15”,18” 12”, 15”, 18”, 21” 1, 2, 36 12, 15”, 18” 12”, 15”, 18”, 21” 1, 2, 3, 48” 12”,15”,18” 12”, 15”, 18”, 21” 1, 2, 3, 4, 60” 12”,15”,18” 12”, 15”, 18”, 21” 1, 2, 3, 4, 5, 6 72” 12”,15”,18” 12”, 15”, 18”, 21” 1, 2, 3, 4, 5, 6.
Larger sizes are not practical in all situations please call to confirm.
Custom sizes are available
STYLE OPTIONS
Lockers:
ITEM DESCRIPTION ‐OPTION Standard Box Type, Single or Multi Tier Z Locker Two tier Z Style Athletic Locker Open Style with lockable seat storage, coat rod, and valuables locker. Tops Flat or Slope Bases 3” high Black base 3/4” thick Handle Vertical friction free design Locks Padlock, Built in Combination, Key Lock, Digi‐Lock, Coin operation. Hooks Double Prong Black Ceiling hook or Metal J Hook Rods Plastic or metal. Hinges Corrosion Proof Full length Integral Plastic Hinge Venting Slotted or Mesh Colors Bone, Glacier Grey, Dove Gray, Military Gray, Mocha, Forest Green,
Blueberry, Black, Red, Burgundy.
SPECIFICATION
Doors and Frames: Constructed from ½” thick high density polyethylene (HDPE) homogeneous color with orange peel finish texture. Full‐length finger joint
design providing uniform frame and vandalism prevention. Frames are one piece construction.
Sides, tops, bottoms, dividers and shelves:
Constructed from 3/8” thick white HDPE with Matt finish. Sides and back of box are formed from a single sheet of HDPE with fused corners.
Top and bottom dividers are captured into corresponding grooves and connected without metal fasteners. Shelves provided in one tier
lockers only are slid into corresponding grooves in sides and back. Shelves are located 12” from locker top.
Latch Bar:
Full‐length latch bar is constructed of ½” thick colored high density polyethylene with a orange peel finish color matched to the door. Latch
bar runs the entire length of the door providing continuous security latching system. Latch lifts up to open door and returns to closed
position after the door is closed.
Hinge:
Full‐length continuous hinge integrated with both door and frame. All plastic construction without any steel or metal parts. Color to match
locker. Corrosion proof, impervious to moisture, chemicals and UV rays.
Handle:
Handle is ADA compliant solid plastic color matched. Friction free design with concealed connections, tamperproof operating independently
of latch bar.
Hasp:
Hasp is 11 gauge (1/8”) stainless steel. Accepts standard padlocks.
Coat hook:
Double coat hook constructed of black poly carbonate. Furnished in 36”, 48”, 16”, and 72” one tier and 60” and 72” two tier lockers only.
Hook is mounted under shelves in one tier and under locker top in two tier lockers. Secured to shelves and tops with stainless steel screws.
Base:
Bases constructed of ¾” thick black HDPE. Standard base height is 3” high ( custom heights available)
Flat Top:
Flat Tops are constructed from ½” thick HDPE color matched to lockers.
Slope Tops:
Slope Tops are constructed from ½” thick HDPE color matched to lockers. Slope tops are attached with back plate and secured from inside of
the locker without exposed screws on the outside of the panels.
End Panel:
End Panels are constructed from ½” thick HDPE color matched to lockers. Used at exposed ends.
Filler Panel:
Filler Panels are constructed from ½” thick HDPE color matched to lockers. Used to complete uneven length runs and to close gaps at walls.
Number Plate:
Number Plates are fabricated from aluminum with black numbers secured with rivets and located with factory pre‐drilled holes. Field
installed.
Mesh Doors:
Full Mesh Doors provide ventilation especially for damp environments.
Built In Key Lock:
Built In Key Lock replaces the standard hasp. Key can only be removed from lock when in locked position. Master key provided. Two keys
supplied for each lock.
Built in Combination Lock:
Built‐In Combination Lock replaces the standard hasp. Master key provided. Programmable with five combinations per lock.
Coin Retain Lock:
Safe O Mat® replaces standard HASP. Available to use either tokens or quarters. User inserts coins or tokens to lock door and release key.
When locker door is opened with key the key is retained in the lock.
Coin return lock:
Safe O Mat® coin lock replaces standard hasp. Available using tokens or quarters. When locker door is opened with key, the key is retained in
the lock and coin or token is returned.
DigiLock®:
ADA compliant battery operated electronic lock.
Coat Rod:
Coat Rod is constructed from PVC and mounted with plastic pole sockets and stainless steel screws.
Drain holes:
Optional drainage slots are placed in the bottom of the locker to allow for hose down.
Wall Hook:
Black powder‐coated zinc wall hooks available.
Logos:
Custom engraved logos machined into the door.
DETAIL
Tier Options, 1, 2, 3, 4, and 6 tiers typical. Shown with standard vent
and mesh option.
“Z” LOCKER (SEE AVAILABLE SIZES)
COLORS
Military G
ray
Dove Grey
Glacie
r Grey
Bone
Mocha
Forre
st Green
Vivid
Red
Burgu
ndy
Black
Blueberry
Hardware
Plastic Hinge Vent
Welded Dovetail
Welded Box
Number Plate
Continuous Strike
Hasp
Handle
Stainless Screws
Hook
Padlock
Built in Combination Lock
Coin/Token Lock
Key Lock
DigiLock
SECTION-10500
Guide Specification: Lockers and Locker Benches
Royal Plastic Lockers. (NOTE; some parts of this spec require custom information specific
to your project) Part 1 –GENERAL 1.1 WORK OF THIS SECTION A. The work of this section includes providing solid plastic polymer lockers and Benches. 1.2 RELATED SECTIONS A. The WORK of the following Section applies to the WORK of this Section. Other Sections of the
Specifications, not referenced below, shall also apply to the extent required for proper performance of this WORK.
1. Section 03300 Cast-in-Place Structural Concrete 2. Section 08710 Finish Hardware
1.3 CODES A. The WORK of this Section shall comply with the current editions of the following codes as
adopted by the Local code, if applicable. 1. Uniform Building Code
1.4 STANDARD SPECIFICATIONS A. Except as otherwise indicated, the current editions of the following apply to the WORK of this
Section:
ASTM B 209 Aluminum and Aluminum-Alloy Sheet and Plate ASTM B 221 Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire,
Shapes, and Tubes ASTM B 241 Aluminum and Aluminum-Alloy Seamless Pipe and Seamless
Extruded Tube 1.5 SHOP DRAWINGS AND SAMPLES A. The following shall be submitted in compliance with Section 01300:
1. Manufacturer’s catalogs containing technical data and installation instructions, shop drawings, and
colors available. 2. Samples of all the materials, finish, and color. The samples shall be clearly marked to show
the manufacturer’s name and product identification. The manufacturer shall offer scale model and full set of color samples.
3. Shop drawings for solid plastic locker benches, verifying all dimensions affecting the
installation. Lockers and benches shall be shown in detail, including method of installation, required fillers, trim, and accessories. Locker numbering sequence information shall be provided if indicated.
1.6 PRODUCT DELIVERY, STORAGE, AND HANDLING A. Delivery of Materials: Products shall be delivered in original, unbroken packages, containers, or
bundles bearing the name of the manufacturer. B. Storage: Products shall be carefully stored in a manner that will prevent damage and in an area
that is protected from the elements. C. Solid plastic locker and benches shall not be delivered until the building is enclosed and ready for
locker installation.
D. Solid plastic locker and bench finishes, as well as adjacent surfaces and materials shall be protected from damage or marring during installation.
PART 2 – PRODUCTS 2.1 MATERIALS, GENERAL A. Solid Polyethylene Resin: High density, solid polymer resin formed under high pressure, with
homogenous color throughout. Provide material with seamless construction with edges rounded and free from saw marks. Colors as selected by the architect from manufacturer’s standards.
1. Internal Sides, Shelves, Tops and Bottoms: Fabricated from high impact, high density,
polyethylene (HDPE) 3/8" thick with homogenous natural white color throughout.
2. Doors, Door frames, Trim and End panels: Made from high density polyethylene (HDPE) Solid plastic 1/2" thick with homogeneous color throughout. Injection molded components not acceptable.
3. Base; Lockers to be installed on a 3" high base. (bases are an optional item)
4. Material Testing: All solid plastic components shall resist deterioration and discoloration
when subjected to the following chemicals and tested in accordance with corrosion-testing procedure established by the United States Plastic Corporation:
Acetic Acid 80% Caustic Soda Nicotine Ammonium Phosphate Cooper Chloride Lime Sulfur Acetone Chlorine Water Soaps Ammonia Liquid Core Oils Potassium Bromide Bleach 12% Hydrochloric Acid 40% Trisodium Phosphate Brine Hydrogen Peroxide 30% Sodium Bicarbonate Borax Isopropyl Alcohol Urea and Urine Citric Acid Lactic Acid 25% Vinegar
B. Hardware:
1. Latch: Continuous spring loaded slide latching mechanism that is capable of accepting a
padlock and shall be securely fastened to the door. Latch mechanism shall be color matched to the locker, attached to the entire length of the door providing a continuous security latch.
2. Handle: Plastic Handle color matched to locker. ADA compliant operating with less than 5 lbs of force. Latch handle to operate independently of latch bar.
3. Hinges: Continuous, integrated into the full length of the door and locker frame, made from entirely plastic to color match the locker. Metal knuckles or pins not acceptable.
4. Coat Hooks: Two prong type made from high impact plastic attached with theft resistant screws or rivets. One hook per opening in lockers 30” high or greater.
2.2 FABRICATION, GENERAL A. Construction: Lockers shall be fabricated square, rigid, and without warp, with faces flat and free
of dents, scratches or chips. B. Solid plastic locker components shall be secured using dado routing and continuous welds and
shall provide a solid and secure construction. Adjacent lockers shall not share a common side panels.
C. Ventilation: Slotted vents shall be provided in door face as follows:
1. Single and Double-tier lockers shall have not less than 6-slotted openings top and bottom. 2. Multi-tier lockers shall have not less than 6-slotted openings at top.
2.3 LOCKER ACCESSORIES A. Locking: Lockers shall be fabricated to receive the following locking devices: (select one:
Padlock Hasp, built in combination lock, coin lock, Digi Lock) B. Number Plates: Number plates shall be manufacturer’s standard etched, embossed or stamped,
number plates with numerals not less than 3/8 inch high fastened with theft resistant rivets. Lockers shall be numbered in sequence as directed by the architect. Number plates shall be attached to face of each locker door, near the top, centered using factory pre-drilled holes.
C. Filler Panels: Filler panels shall be provided where indicated or required for a complete
installation. Panels shall be fabricated of not less than ½ inch solid plastic, and finished to match locker units.
2.4 LOCKER UNITS A. Locker units shall conform to the following requirements:
1. Lockers shall consist of (example: two-person, double tier lockers (sizes by each job need) for mounting on suitable curb, securely tied in banks as indicated; provided complete with number plates. (Select type of curb material and show mounting height of base for lockers.)
2.5 MANUFACTURERS A. Products of the types indicated shall be as manufactured by one of the following (or approved
equal by architect):
Royal Lockers as Represented by Service Oriented Sales Ph (877) 767-4636 PART 3 – EXECUTION 3.1 LOCKERS A. Lockers shall be fastened to the structures in accordance with manufacturer’s printed
recommendations and in conformance with the Uniform Building Code. Frames and doors shall form a flush exterior when installed. Lockers shall be plumb, level, rigid and securely fastened in banks.
B. Fastenings shall be spaced not more than 48 inches on center, and applied through back-up reinforcing plates where necessary to avoid distortion. Fasteners shall be concealed insofar as possible.
C. Locker shall be jointed side by side with stainless steel theft resistant through bolts.
D. Trim filler panels shall be installed where indicated. Using concealed fasteners to provide flush, hairline joints against adjacent surfaces.
3.2 LOCKER ROOM BENCHES (option, if needed) A. Bench tops to be 9 ½” wide and 1 ½” thick with all edges machined to a ¼” radius and all
exposed edges free of saw marks.
B. Solid polyethylene resin benches shall be installed in compliance with manufacturer’s instruction. C. Pedestal leg shall 2” Dia. and base to be 6” Dia. extruded anodized black aluminum.
D. Secure to floor with stainless steel expansion anchors.
3.3 ADJUST AND CLEAN A. Doors and latches shall be adjusted to operate easily without binding. Integral locking devices
shall be verified as operating properly. B. Marred finishes shall be touched up, but units that cannot be restored to factory-finished appearance
Shall be replaced. Only materials and procedures recommended or furnished by locker manufacturer shall
be used.
top related