ssv
Post on 21-Jul-2016
215 Views
Preview:
TRANSCRIPT
D1
D2
L3
L1
L2
2
3⁄8FILL VENT
3⁄82 HOLES
1
M1
71⁄16 85⁄16
315⁄16
M2
1⁄24 HOLES
SSV SeriesVerticalMulti-StagePumps
SSV
300 LB. FLANGE
2
The SSV series of vertical multi-stage pumps from G&L has been designedwith exclusive technical benefits to serve the needs of commercial, OEM andHVAC customers.
• Standard NEMA motors permit a wide variety of options and fastfield service.
• NPT threads, ANSI flanges, in-line or top/bottom connections easilyfit your piping requirements. The top discharge version may be swungin four directions.
• AISI 304 or 316L stainless steel liquid end components handle more ofyour pumping needs.
• Seal housing design promotes liquid flow and eliminates entrapped air orheat which could cause premature failure.
• Impeller O-ring seal produces high pressure and efficiency per stage tokeep energy costs down.
• Impeller spacing is automatic for quick installation and reduced wear.
• Simplified design for maximum reliability and faster repair.
• Optional horizontal mounting and victaulic connections are available.
A Full Rangeof Product Features
3
The SSV series is designed for usein a wide range of high pressureapplications with flow rates up to300 GPM. Examples include:
• Circulation of liquids withoutsuspended solids
• Pressure boosting and watersupply
• Agricultural and commercialirrigation systems
• Commercial washing systems
• Boiler feed and condensatereturn
• Water treatment, reverseosmosis and filtration systems
• Circulation of coolants suchas glycol
• Pure water (demineralized anddeionized) applications
• Circulation of hot and coldwater for HVAC installations
Typical Applications
4
SSV Product LineNumbering System
The various versions of the SSV line are identified by a product code number on the pump label. This number is alsothe catalog number for the pump. The meaning of each digit in the product code number is shown below.Note: Not all combinations are possible. Consult your G&L distributor.Example Product Code2 SV A 1 D 2 B 1 H
Options: H = Horizontal mount, refer to back coverVIC = Victaulic connections (1SVB/D – 4SVB/D only), see below
Mechanical Seal Options:
Number of Stages:B = 2 D = 4 F = 6 H = 8 K = 10 M= 12 P = 14 R = 16 V = 20 Z = 24C = 3 E = 5 G = 7 J = 9 L = 11 N = 13 Q = 15 T = 18 X = 22
Driver: (50 Hz, no single phase number 0, 1, 4)1 = 1 PH, ODP 3 = 575V, ODP 5 = 3 PH, TEFC 7 = 3 PH, XP 9 = 3 PH, TEFC with premium efficiency2 = 3 PH, ODP 4 = 1 PH, TEFC 6 = 575V, TEFC 8 = 575V, XP 0 = 1 PH, XP
HP Rating: C = 1⁄2 E = 1 G = 2 J = 5 L = 10 N = 20 Q = 30D = 3⁄4 F = 11⁄2 H = 3 K = 71⁄2 M= 15 P = 25
Hertz/RPM: 1 = 60 Hz, 3500 RPM 3 = 60 Hz, 3500 RPM, 380 V 5 = 60 Hz, 3500 RPM, 220-380 V, D.O.L.2 = 50 Hz, 2900 RPM, 190-380 V, (50 Hz motor) 4 = 50 Hz, 2900 RPM, 460 V 6 = 60 Hz, 3500 RPM, 380 V, Y-DELTA
Material and Suction/Discharge:A = 304 stainless steel, in-line NPT threaded oval flange connections (1, 2, 3, 4SV only)B = 304 stainless steel, in-line ANSI flange (1, 2, 3, 4SV. 304/cast iron 5 and 6SV)C = 304 stainless steel, top/bottom ANSI flange connectionsD = 316 stainless steel, in-line ANSI flange
Product Line: Stainless steel vertical
Nominal Flow: 1 = 15 GPM 2 = 28 GPM 3 = 55 GPM4 = 86 GPM 5 = 145 GPM 6 = 290 GPM
Code No. Rotary Stationary Elastomer Where Offered0 Silicon Carbide Silicon Carbide Viton Standard on all units1 Carbon Silicon Carbide EPR 5SV and 6SV only2 Tungsten Carbide Carbon EPR3 Tungsten Carbide Carbon Viton5 Carbon Silicon Carbide Viton All units
1SV, 2SV,3SV and 4SV
Dimensions of 1SV and 2SV with victaulic connections
320
Dimensions of 3SV and 4SV with victaulic connections
Dimensions of 1SV and 2SV with couplings and pipe adapters Dimensions of 3SV and 4SV with couplings and pipe adapters
210
50
20
ø42.2
261
90
ø50.3
30
Victaulic Connections Option
378
3.53(90)
10.25(261)
14.85(378)
12.59(320)
8.25(210) 1.
18(3
0).75
(20)
1.94(50)
11⁄4" Victaulicconnection
11⁄4" x 111⁄2" NPTmale thread
2" Victaulicconnection
2" x 111⁄2" NPTmale thread
1.66(ø42.2)
2.37(ø62.3)
• Victaulic type connections are available as an option for the 1SV, 2SV, 3SV and 4SV in either 304 or 316 version.• This option is not available for the 5SV, 6SV, or in Top/Bottom configuration.• Pumps using this option are shipped with victaulic fitted suction and discharge connections. The connecting coupling and pipe end adapters may be ordered separately.• Dimensions are in inches (mm).
5
Base Models: 1SV, 2SV, 3SVand 4SV Major Components
1 Standard NEMA vertical motor
2 Rigid coupling
3 Motor adapter
4 Coupling guard
5 Stainless steel seal housing
6 Mechanical seal
7 Stainless steel fill and drain plugs
8 Tie-rods
9 O-ring
10 Stainless steel pump casing
11 Stainless steel diffuser
12 Stainless steel impeller
13 Tungsten carbide shaft sleeve
14 Ceramic bushing
15 Stainless steel shaft
16 Stainless steel pump body
17 Pump base
Top and bottom suction/discharge design
Series C
In-line NPT connections
In-line ANSIflange connections
1
3
2
7
6
10
1113
16
17
415
9
5
8
12
14
7
9
Series B or D
Series A
6
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 60 Hz, 3500 RPM,single phase 1⁄2 to 3 HP (115/208–230 V) 5 HP (208–230 V) and three phase(208–230/460 V). 1SV horsepowers from 1⁄2 to 5. For other motor options,contact the factory. Above motors are 1.25 S.F. for 1⁄2, 3⁄4 and 1 HP. 1.15 S.F.for 11⁄2–5 HP.
Construction: 304 or 316 stainless steelCapacities: 3– 22 gallons per minute (1.1– 5 m3/hr)Heads: 40 – 760 feet TDH (12– 232 meters)Staging: 2–16Minimum flow: 3 GPMMaximum working 230 PSI (16 bar) for the NPT version andpressure: 360 PSI (25 bar) for the ANSI flange versionTemperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
1SVA x 2–11 NPT In-line1SVB x 2–16 ANSI flange In-line1SVC x 5 –16 ANSI flange Top/bottom1SVD x 2–16 ANSI flange In-line
Piping Connections: Suction and discharge openings are 1" NPT.ANSI flanges are class 300, 11⁄4" flanges. Victaulic are 11⁄4".
Solids handling: Although not recommended, the pumpmay pass a 1⁄32" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O-rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plugs 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast aluminum Same
Pump base Aluminum casting Same
1SV Performance CurvesBase Model: 1SVGeneral Pump Description
1SV Motors
0
100
200
300
400
500
600
700
0 5 10 15 20 US GPM
FE
ET
TO
TAL
DY
NA
MIC
HE
AD
CAPACITY
20
40
60
EF
F %
8001SV 60 Hz3450 RPM
0
2
4
6
8
10
NP
SH
(ft)
0 1 2 3 4 5 m3/h
0
20
40
60
80
100
120
140
160
180
200
220
240
ME
TER
S
16 Stage 5HP15 Stage 5HP
13 Stage 5HP
11 Stage 3HP
9 Stage 3HP8 Stage 3HP
6 Stage 2HP
5 Stage 11⁄2HP4 Stage 1HP
3 Stage 3⁄4HP
7 Stage 2HP
2 Stage 1⁄2HP
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 1SV
5 Carbon Silicon Carbide Viton
7
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 L4 M1 M2 D1 D2 ODP TEFC
26 7⁄8 11 1⁄4 5 5⁄8 6526 13⁄16 11 3⁄16 5 9⁄16 7027 7⁄8 11 1⁄4 5 5⁄8 70
28 11⁄16 12 1⁄16 5 9⁄16 8028 13⁄16 11 1⁄4 5 5⁄8 7029 5⁄8 12 1⁄16 5 9⁄16 8030 3⁄4 12 3⁄16 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 10531 3⁄4 12 3⁄16 5 5⁄8 8031 5⁄8 12 1⁄16 5 9⁄16 105
33 11⁄16 12 3⁄16 5 5⁄8 8533 9⁄16 12 1⁄16 5 9⁄16 10535 1⁄2 12 11038 9⁄16 15 1⁄16 12037 7⁄16 12 11040 1⁄2 15 1⁄16 12538 7⁄16 12 11541 1⁄2 15 1⁄16 125
5 56C 11⁄2 15 5⁄8 8 7⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 2 16 5⁄8 9 7⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 2 17 9⁄16 10 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 3 18 9⁄16 11 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 3 19 9⁄16 12 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 3 21 1⁄2 14 3⁄4 5 1⁄4 6 5⁄8 6 3⁄4
13 184TC 5 23 1⁄2 16 3⁄4 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
15 184TC 5 25 7⁄16 18 11⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
16 184TC 5 26 7⁄16 19 11⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
1SV Dimensions and Weights
1SVA Series Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
20 7⁄8 9 3⁄16 4 3⁄8 4 15⁄16 4521 9 5⁄16 4 1⁄2 5 1⁄8 45
22 1⁄2 9 13⁄16 4 3⁄8 4 15⁄16 5022 1⁄8 9 15⁄16 4 1⁄2 5 1⁄8 5024 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 55
24 13⁄16 11 3⁄16 5 1⁄4 5 9⁄16 6 5⁄8 6525 7⁄8 11 1⁄4 5 5⁄8 65
25 13⁄16 11 3⁄16 5 9⁄16 7026 7⁄8 11 1⁄4 5 5⁄8 70
27 11⁄16 12 1⁄16 5 9⁄16 8027 7⁄8 11 1⁄4 5 5⁄8 70
28 11⁄16 12 1⁄16 5 9⁄16 8029 3⁄4 12 3⁄16 5 5⁄8 8029 5⁄8 12 1⁄16 5 9⁄16 10530 3⁄4 12 3⁄16 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 105
32 11⁄16 12 3⁄16 5 5⁄8 8532 9⁄16 12 1⁄16 5 9⁄16 110
Stage
2 56C 1⁄2 11 11⁄16 5 11⁄16 6 3⁄4
3 56C 3⁄4 12 11⁄16 5 11⁄16 6 3⁄4
4 56C 1 13 5⁄8 6 3⁄4
5 56C 1 1⁄2 14 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 2 15 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 2 16 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 3 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 3 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 3 20 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
Stage1SVC Series
(All dimensions are in inches, weights are total unit weight.)
11⁄4
D1
D2
L3
L1
L2
3
415⁄163⁄8 DRAIN
3⁄8FILL VENT
M1
71⁄1685⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
1
L4
300 LB. FLANGE
CAPACITORCOVER ONSINGLE PHASEONLY
1 NPT
D1
D2
L3
L1
L2
2
65⁄16
3⁄8 DRAIN
3⁄8FILL VENT
3⁄82 HOLES
3⁄4
M1
71⁄16 85⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
CAPACITORCOVER ONSINGLE PHASEONLY
1SVB Series or 1SVD Series
M1
71⁄16 85⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
11⁄4
300 LB. FLANGE
D1
D2
L3
L1
L2
3
197⁄8
3⁄8 DRAIN
3⁄8FILL VENT
CAPACITORCOVER ONSINGLE PHASEONLY
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
21 7⁄8 9 3⁄16 4 3⁄8 4 15⁄16 4522 9 5⁄16 4 1⁄2 5 1⁄8 45
23 7⁄16 9 13⁄16 4 3⁄8 4 15⁄16 5023 9⁄16 9 15⁄16 4 1⁄2 5 1⁄8 5025 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 55
25 13⁄16 11 3⁄16 5 1⁄4 5 9⁄16 6 5⁄8 6526 7⁄8 11 1⁄4 5 5⁄8 65
26 13⁄16 11 3⁄16 5 9⁄16 7027 7⁄8 11 1⁄4 5 5⁄8 70
28 11⁄16 12 1⁄16 5 9⁄16 8028 13⁄16 11 1⁄4 5 5⁄8 7029 5⁄8 12 1⁄16 5 9⁄16 8030 3⁄4 12 3⁄16 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 10531 3⁄4 12 3⁄16 5 5⁄8 8031 5⁄8 12 1⁄16 5 9⁄16 105
33 11⁄16 12 3⁄16 5 5⁄8 8533 9⁄16 12 1⁄16 5 9⁄16 11035 1⁄2 12 11038 9⁄16 15 1⁄16 12037 7⁄16 12 11040 1⁄2 15 1⁄16 12538 7⁄16 12 11541 1⁄2 15 1⁄16 125
Stage
2 56C 1⁄2 12 11⁄16 5 11⁄16 6 3⁄4
3 56C 3⁄4 13 5⁄8 5 11⁄16 6 3⁄4
4 56C 1 14 5⁄8 6 3⁄4
5 56C 1 1⁄2 15 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 2 16 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 2 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 3 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 3 19 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 3 21 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
13 184TC 5 23 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
15 184TC 5 25 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
16 184TC 5 26 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
8
Construction: 304 or 316 stainless steelCapacities: 6– 40 gallons per minute (2.2– 9 m3/hr)Heads: 40– 620 feet TDH (12–189 meters)Staging: 2–15Minimum flow: 6 GPMMaximum working 230 PSI (16 bar) for the NPT version andpressure: 360 PSI (25 bar) for the ANSI flange versionTemperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
2SVA x 2–11 NPT In-line2SVB x 2–15 ANSI flange In-line2SVC x 5–15 ANSI flange Top/bottom2SVD x 2–15 ANSI flange In-line
Piping Connections: Suction and discharge openings are 11⁄4" NPT.ANSI flanges are class 300, 11⁄4" flanges. Victaulic are 11⁄4".
Solids handling: Although not recommended, the pumpmay pass a 1⁄16" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O- rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plugs 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast aluminum Same
Pump base Cast aluminum Same
0
100
200
300
400
500
600
700
0 10 20 30 40 US GPM
FE
ET
TO
TAL
DY
NA
MIC
HE
AD
CAPACITY
20
40
60
EF
F %
0
2
4
6
8
10
NP
SH
(ft)
2SV 60 Hz3450 RPM
ME
TE
RS
0
20
40
60
80
100
120
140
160
180
200
0 2 3 4 5 6 7 8 9 m3/h1
15 Stage 5HP
13 Stage 5HP
11 Stage 5HP
9 Stage 3HP8 Stage 3HP
6 Stage 2HP
3 Stage 1HP
4 Stage 11⁄2HP
7 Stage 3HP
2 Stage 3⁄4HP
5 Stage 2HP
2SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 60 Hz, 3500 RPM,single phase 1⁄2 to 3 HP (115/208–230 V) 5 HP (208–230 V) and three phase(208–230/460 V). 2SV horsepowers from 1⁄2 to 5. For other motor options,contact the factory. Above motors are 1.25 S.F. for 1⁄2, 3⁄4 and 1 HP. 1.15 S.F.for 11⁄2 to 5 HP.
2SV Performance CurvesBase Model: 2SVGeneral Pump Description
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 2SV
5 Carbon Silicon Carbide Viton
9
(All dimensions are in inches, weights are total unit weight.)
2SVA Series
2SVC Series Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 L4 M1 M2 D1 D2 ODP TEFC
26 7⁄8 11 1⁄4 5 5⁄8 7027 11⁄16 12 1⁄16 5 9⁄16 7527 7⁄8 11 1⁄4 5 5⁄8 70
28 11⁄16 12 1⁄16 5 9⁄16 8029 3⁄4 12 3⁄16 5 5⁄8 8029 5⁄8 12 1⁄16 5 9⁄16 10030 3⁄4 12 3⁄16 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 10531 3⁄4 12 3⁄16 5 5⁄8 8031 5⁄8 12 1⁄16 5 9⁄16 10533 1⁄2 12 11036 9⁄16 12 1⁄16 12035 1⁄2 12 11038 9⁄16 15 1⁄16 12037 7⁄16 12 11040 1⁄2 15 1⁄16 125
Stage
2SV Dimensions and Weights
11⁄4
D1
D2
L3
L1
L2
3
415⁄163⁄8 DRAIN
3⁄8FILL VENT
M1
71⁄1685⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
1
L4
300 LB. FLANGE
CAPACITORCOVER ONSINGLE PHASEONLY
11⁄4 NPT
D1
D2
L3
L1
L2
2
65⁄16
3⁄8 DRAIN
3⁄8FILL VENT
3⁄82 HOLES
3⁄4
M1
71⁄16 85⁄16
315⁄16
55⁄16
M2
1⁄24 HOLES
CAPACITORCOVER ONSINGLE PHASEONLY
2SVB Series or 2SVD Series
M1
71⁄16 85⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
11⁄4
300 LB. FLANGE
D1
D2
L3
L1
L2
3
197⁄8
3⁄8 DRAIN
3⁄8FILL VENT
CAPACITORCOVER ONSINGLE PHASEONLY
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
21 1⁄2 9 13⁄16 4 3⁄8 4 15⁄16 4521 5⁄8 9 15⁄16 4 1⁄2 5 1⁄8 5023 5⁄16 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 5523 7⁄8 11 3⁄16 5 1⁄4 5 9⁄16 6 5⁄8 6524 7⁄8 11 1⁄4 5 5⁄8 65
34 13⁄16 11 3⁄16 5 9⁄16 6525 7⁄8 11 1⁄4 5 5⁄8 70
26 11⁄16 12 1⁄16 5 9⁄16 7526 7⁄8 11 1⁄4 5 5⁄8 70
27 11⁄16 12 1⁄16 5 9⁄16 8028 13⁄16 12 3⁄16 5 5⁄8 8028 11⁄16 12 1⁄16 5 9⁄16 10029 3⁄4 12 3⁄16 5 5⁄8 8029 5⁄8 12 1⁄16 5 9⁄16 10530 3⁄4 12 3⁄16 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 10532 9⁄16 12 11035 5⁄8 15 1⁄16 120
2 56C 3⁄4 11 11⁄16 5 11⁄16 6 3⁄4
3 56C 1 12 11⁄16 6 3⁄4
4 56C 1 1⁄2 13 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
5 56C 2 14 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 2 15 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 3 16 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 3 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 3 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 184TC 5 20 9⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
Stage
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
22 1⁄2 9 13⁄16 4 3⁄8 4 15⁄16 4522 5⁄8 9 15⁄16 4 1⁄2 5 1⁄8 5024 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 55
24 13⁄16 11 3⁄16 5 1⁄4 5 9⁄16 6 5⁄8 65
25 7⁄8 11 1⁄4 5 5⁄8 6525 13⁄16 11 3⁄16 5 9⁄16 6526 7⁄8 11 1⁄4 5 5⁄8 70
27 11⁄16 12 1⁄16 5 9⁄16 7527 7⁄8 11 1⁄4 5 5⁄8 70
28 11⁄16 12 1⁄16 5 9⁄16 8029 3⁄4 12 3⁄16 5 5⁄8 8029 5⁄8 12 1⁄16 5 9⁄16 10030 3⁄4 12 3⁄16 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 10531 3⁄4 12 3⁄16 5 5⁄8 8031 5⁄8 12 1⁄16 5 9⁄16 10533 1⁄2 12 11036 9⁄16 15 1⁄16 12035 1⁄2 12 11038 9⁄16 15 1⁄16 12037 7⁄16 12 11040 1⁄2 15 1⁄16 125
Stage
2 56C 3⁄4 12 11⁄16 5 11⁄16 6 3⁄4
3 56C 1 13 5⁄8 6 3⁄4
4 56C 1 1⁄2 14 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
5 56C 2 15 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 2 16 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 3 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 3 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 3 19 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 184TC 5 21 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
13 184TC 5 23 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
15 184TC 5 25 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
55⁄16
55⁄16
5 56C 2 15 5⁄8 8 7⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 2 16 5⁄8 9 7⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 3 17 9⁄16 10 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 3 18 9⁄16 11 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 3 19 9⁄16 12 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 184TC 5 21 1⁄2 14 3⁄4 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
13 184TC 5 23 1⁄2 16 3⁄4 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
15 184TC 5 25 7⁄16 18 11⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
10
Base Model: 3SVGeneral Pump Description
3SV Performance Curves
Construction: 304 or 316 stainless steelCapacities: 11–75 gallons per minute (4.5–17 m3/hr)Heads: 60–790 feet TDH (18– 241 meters)Staging: 2–13Minimum flow: 11 GPMMaximum working 230 PSI (16 bar) for the NPT version andpressure: 360 PSI (25) for the ANSI flange versionTemperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
3SVA x 2 – 8 NPT In-line3SVB x 2–13 ANSI flange In-line3SVC x 5–13 ANSI flange Top/bottom3SVD x 2–13 ANSI flange In-line
Piping Connections: Suction and discharge openings are 11⁄2" NPT.ANSI flanges are class 300, 2" flanges. Victaulic are 2".
Solids handling: Although not recommended, the pumpmay pass a 1⁄8" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O-rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plug 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast aluminum below5 HP and cast iron5 HP and above Same
Pump base Cast aluminum Same
0
100
200
300
400
500
600
700
0 20 40 60 80 US GPM
FE
ET
TO
TAL
DY
NA
MIC
HE
AD
CAPACITY
40
60
80
EF
F %
800
3SV 60 Hz3450 RPM
0
2
4
6
8
10
NP
SH
(ft)
12
0
20
40
60
80
100
120
140
160
180
200
220
240
ME
TE
RS
0 4 6 8 10 12 14 16 18 m3/h2
20
13 Stage 15HP12 Stage 15HP
11 Stage 10HP
10 Stage 10HP
9 Stage 10HP
3 Stage 3HP
5 Stage 5HP
4 Stage 5HP
2 Stage 2HP
8 Stage 71⁄2HP
7 Stage 71⁄2HP
6 Stage 71⁄2HP
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 60 Hz, 3500 RPM,single phase 2 to 3 HP (115/208–230 V) 5 HP (208–230 V) and three phase2 to 10 HP (208–230/460 V). 15 HP (230/460 V) 3 SV horsepowers from 2 to15. For other motor options, contact the factory. Above motors are 1.15 S.F.
3SV Motors
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 3SV
5 Carbon Silicon Carbide Viton
11
D1
D2
L3
L1
L2
3⁄8 DRAIN
3⁄8FILL VENT
M2
815⁄32 95⁄8
51⁄871⁄2
M11⁄2
4 HOLES
1
31⁄8
77⁄8
15⁄322 HOLES
11⁄2 NPT
CAPACITORCOVER ONSINGLEPHASEONLY
3SVA Series
3SVC Series
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
26 9⁄16 11 1⁄4 5 5⁄8 7527 3⁄8 12 1⁄16 5 9⁄16 85
29 12 3⁄16 5 5⁄8 8528 7⁄8 12 1⁄16 5 9⁄16 11030 5⁄16 12 11533 3⁄8 15 1⁄16 125
31 13⁄16 12 11534 7⁄8 15 1⁄16 130
34 13⁄16 12 12537 7⁄8 15 1⁄16 13536 1⁄4 12 13039 5⁄16 15 1⁄16 135
Stage
StageMotor Dimensions (max.) Wt. (lbs.)
Frame HP L1 L2 L3 L4 M1 M2 D1 D2 ODP TEFC30 3⁄4 12 115
33 13⁄16 15 1⁄16 12532 1⁄4 12 11535 5⁄16 15 1⁄16 13035 1⁄4 12 12538 5⁄16 15 1⁄16 13536 11⁄16 12 13039 3⁄4 15 1⁄16 135
213TC (ODP) 175215TC (TEFC) 200213TC (ODP) 175215TC (TEFC) 200215TC (ODP) 48 15⁄16 15 9⁄16 7 3⁄8 9 9⁄16 185254TC (TEFC) 53 19 5⁄8 8 15⁄16 11 1⁄2 315
(All dimensions are in inches, weights are total unit weight.)
2
D1
D2
L3
L1
L2
515⁄16 3⁄8 DRAIN
3⁄8FILL VENT
M1
815⁄3295⁄8
51⁄871⁄2
M2
1⁄24 HOLES
L4
300 LB. FLANGE
13⁄16
39⁄16
CAPACITORCOVER ONSINGLEPHASE ONLY
3SVB Series or 3SVD Series Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
27 11 1⁄4 5 5⁄8 7527 13⁄16 12 1⁄16 5 9⁄16 8529 7⁄16 12 3⁄16 5 5⁄8 8529 5⁄16 12 1⁄16 5 9⁄16 11030 3⁄4 12 115
33 13⁄16 15 1⁄16 12532 1⁄4 12 11535 5⁄16 15 1⁄16 13035 1⁄4 12 12538 5⁄16 15 1⁄16 13536 11⁄16 12 12539 3⁄4 15 1⁄16 135
213TC (ODP) 175215TC (TEFC) 200213TC (ODP) 175215TC (TEFC) 200215TC (ODP) 48 15⁄16 15 9⁄16 7 3⁄8 9 9⁄16 185254TC (TEFC) 53 19 5⁄8 8 15⁄16 11 1⁄2 315
Stage
2
D1
D2
L3
L1
L2
1113⁄16
3⁄8 DRAIN
3⁄8FILL VENT
M2
815⁄32 95⁄8
51⁄871⁄2
M11⁄2
4 HOLES
300 LB. FLANGE
13⁄16
39⁄16
CAPACITORCOVER ONSINGLE PHASEONLY
3SV Dimensions and Weights
2 56C 2 15 5⁄16 5 1⁄4 6 5⁄8 6 3⁄4
3 56C 3 16 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
4 184TC 5 18 5⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
5 184TC 5 19 13⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
6&7 184TC 7 1⁄2 22 13⁄16 5 7⁄8 – 7 7⁄8 11 13⁄16
8 184TC 7 1⁄2 24 1⁄4 5 7⁄8 – 7 7⁄8 11 13⁄16
2 56C 2 15 3⁄4 5 1⁄4 6 5⁄8 6 3⁄4
3 56C 3 17 1⁄4 5 1⁄4 6 5⁄8 6 3⁄4
4 184TC 5 18 3⁄4 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
5 184TC 5 20 1⁄4 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
6 & 7 184TC 7 1⁄2 23 1⁄4 5 7⁄8 – 7 7⁄8 11 13⁄16
8 184TC 7 1⁄2 24 11⁄16 5 7⁄8 – 7 7⁄8 11 13⁄16
9 & 10 10 44 7⁄16 28 7⁄8 15 9⁄16 7 3⁄8 – 9 9⁄16 11 13⁄16
11 10 45 15⁄16 30 3⁄8 15 9⁄16 7 3⁄8 – 9 9⁄16 11 13⁄16
12&13 15 33 3⁄8 – 11 13⁄16
4 184TC 5 18 3⁄4 11 13⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
5 184TC 5 20 1⁄4 12 11⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
6 & 7 184TC 7 1⁄2 23 1⁄4 15 11⁄16 5 7⁄8 – 7 7⁄8 11 13⁄16
8 184TC 7 1⁄2 24 11⁄16 17 3⁄16 5 7⁄8 – 7 7⁄8 11 13⁄16
9 & 10 10 44 7⁄16 28 7⁄8 15 9⁄16 20 3⁄16 7 3⁄8 – 9 9⁄16 11 13⁄16
11 10 45 15⁄16 30 3⁄8 15 9⁄16 21 11⁄16 7 3⁄8 – 9 9⁄16 11 13⁄16
12&13 15 33 3⁄8 24 5⁄8 – 11 13⁄16
12
Construction: 304 or 316 stainless steelCapacities: 17–110 gallons per minute (4– 25 m3/hr)Heads: 90–750 feet TDH (30– 229 meters)Staging: 2–10Minimum flow: 17 GPMMaximum working 360 PSI (25 bar)pressure:Temperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
4SVB x 2–10 ANSI flange In-line4SVC x 4–10 ANSI flange Top/bottom4SVD x 2–10 ANSI flange In-line
Piping Connections: Suction and discharge openings are 2" ANSIclass 300 flanges. Victaulic are 2".
Solids handling: Although not recommended, the pumpmay pass a 3⁄16" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O-rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plug 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast iron Same
Pump base Cast aluminum Same
0
100
200
300
400
500
600
700
0 25 50 75 100 US GPM
FE
ET
TO
TAL
DY
NA
MIC
HE
AD
CAPACITY
40
60
80
EF
F %
0
2
4
6
8
10
NP
SH
(ft)
NPSH Deaerated Liquids (i.e., Boiler Feed)
4SV 60 Hz3450 RPM
800
125
12
14
16
ME
TE
RS
0
20
40
60
80
100
120
140
160
180
200
220
240
0 10 15 20 25 m3/h5
10 Stage 20HP
9 Stage 20HP
8 Stage 15HP
6 Stage 15HP
4 Stage 71⁄2HP
7 Stage 15HP
3 Stage 71⁄2HP
5 Stage 10HP
2 Stage 5HP
4SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 60 Hz, 3500 RPM,single phase 2 to 3 HP (115/208–230 V) 5 HP (208–230 V) and three phase2 to 10 HP (208–230/460 V). 15 and 20 HP (230/460 V) 4SV horsepowersfrom 2 to 20. For other motor options, contact the factory. Above motors are1.15 S.F.
4SV Performance CurvesBase Model: 4SVGeneral Pump Description
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 4SV
5 Carbon Silicon Carbide Viton
13
4SV Dimensions and Weights
4SVB Series or 4SVD Series Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
27 3⁄4 12 11030 13⁄16 15 1⁄16 12029 1⁄4 12 12032 5⁄16 15 1⁄16 12530 3⁄4 12 120
33 13⁄16 15 1⁄16 125213TC (ODP) 165215TC (TEFC) 185215TC (ODP) 40 15 9⁄16 7 3⁄8 9 9⁄16 170254TC (TEFC) 44 1⁄16 19 5⁄8 8 15⁄16 11 1⁄2 300215TC (ODP) 41 1⁄2 15 9⁄16 7 3⁄8 9 9⁄16 175254TC (TEFC) 45 9⁄16 19 5⁄8 8 15⁄16 11 1⁄2 305254TC (ODP) 45 5⁄16 16 7⁄16 8 15⁄16 11 1⁄2 275256TC (TEFC) 48 7⁄8 20 9 5⁄8 12 5⁄16 335
Stage
(All dimensions are in inches, weights are total unit weight.)
StageMotor Dimensions (max.) Wt. (lbs.)
Frame HP L1 L2 L3 L4 M1 M2 D1 D2 ODP TEFC30 3⁄4 12 120
3313⁄16 15 1⁄16 125213TC (ODP) 165215TC (TEFC) 185215TC (ODP) 40 15 9⁄16 7 3⁄8 9 9⁄16 170254TC (TEFC) 44 1⁄16 19 5⁄8 8 15⁄16 11 1⁄2 300215TC (ODP) 41 1⁄2 15 9⁄16 7 3⁄8 9 9⁄16 175254TC (TEFC) 45 9⁄16 19 5⁄8 8 15⁄16 11 1⁄2 305254TC (ODP) 45 5⁄16 16 7⁄16 8 15⁄16 11 1⁄2 275256TC (TEFC) 48 7⁄8 20 9 5⁄8 12 5⁄16 335
4SVC Series
2
D1
D2
L3
L1
L2
515⁄16 3⁄8 DRAIN
3⁄8FILL VENT
M1
815⁄3295⁄8
51⁄871⁄2
1⁄24 HOLES
L4
300 LB. FLANGE
13⁄16
39⁄16
2
D1
D2
L3
L1
L2
1113⁄16
3⁄8 DRAIN
3⁄8FILL VENT
M2
815⁄32 95⁄8
51⁄871⁄2
M11⁄2
4 HOLES
300 LB. FLANGE
13⁄16
39⁄16
CAPACITORCOVER ONSINGLE PHASEONLY
2 184TC 5 15 3⁄4 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
3 184TC 7 1⁄2 17 1⁄4 5 7⁄8 – 7 7⁄8 11 13⁄16
4 184TC 7 1⁄2 18 3⁄4 5 7⁄8 – 7 7⁄8 11 13⁄16
5 10 37 21 7⁄16 15 9⁄16 7 3⁄8 – 9 9⁄16 11 13⁄16
6 & 7 15 24 7⁄16 – 11 13⁄16
8 15 25 15⁄16 – 11 13⁄16
9 & 10 20 28 7⁄8 – 11 13⁄16
4 184TC 7 1⁄2 18 3⁄4 11 3⁄16 5 7⁄8 – 7 7⁄8 11 13⁄16
5 10 37 21 7⁄16 15 9⁄16 12 11⁄16 7 3⁄8 – 9 9⁄16 11 13⁄16
6 & 7 15 24 7⁄16 15 11⁄16 – 11 13⁄16
8 15 25 15⁄16 17 3⁄16 – 11 13⁄16
9 & 10 20 28 7⁄8 20 3⁄16 – 11 13⁄16
14
0
100
200
300
400
500
600
700
0 75 125 150 US GPM
FE
ET
TO
TAL
DY
NA
MIC
HE
AD
CAPACITY
40
60
80
EF
F %
0
2
4
6
8
10
NP
SH
(ft)
5SV 60 Hz3450-3525 RPM800
12
14
100 175
0
20
40
60
80
100
120
140
160
180
200
220
240
ME
TE
RS
0 15 20 25 30 35 40 m3/h5 10
5025
8 Stage 30HP 3525RPM
6 Stage 25HP 3525RPM
4 Stage 15HP 3450RPM
7 Stage 25HP 3525RPM
3 Stage 15HP 3450RPM
5 Stage 20HP 3450RPM
2 Stage 10HP 3450RPM
20
Base Model: 5SVGeneral Pump Description
Construction: 304 or 316 stainless steelCapacities: 28–180 gallons per minute (15– 40 m3/hr)Heads: 100– 760 feet TDH (30– 232 meters)Staging: 2– 8Minimum flow: 28 GPMMaximum workingpressure:
Temperatures: Standard liquid temperature from -13°F (-25°C) to250°F (120°C)
Solids handling: Although not recommended, the pumpmay pass a 3⁄16" sphere.
Design options: MaterialType 304 316 Stages Connections Location
5SVB x 2– 8 ANSI flange In-line5SVD x 2– 8 ANSI flange In-line
Piping Connections: Suction and discharge openings are 21⁄2". ANSI class125 cast iron (150 steel) flanges up to three stages andclass 250 cast iron (300 steel) for four stage and above.
Component 304 316Materials Version Version
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 431 stainless steel 316 SS
Pump casing 304 stainless steel 316L SS
Intermediate crossover Cast iron Cast 316 SS
Top seal housing Cast iron 316 SS
Inner bowls 316L stainless steel Same
Diffusers 316L stainless steel Same
Impellers 316L stainless steel Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316 stainless steel Same
Mechanical seal
Priming and drain plugs Nickel plated brass 316 SS
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast iron Same
Pump body/base Cast iron Cast 316 SS
5SV 2 – 5 Stage Performance Curves
5SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 60 Hz, 3500 RPM,three phase 10 HP (208–230/460 V). 15 and 30 HP (230/460 V) 5SVhorsepowers from 10 to 30. For other motor options, contact the factory.Above motors are 1.15 S.F.
Material Maximum workingType 304 316 Stages pressure in psi. (Bar)
5SVB x 2– 3 175 (12)4–8 360 (25)
5SVD x 2– 3 275 (19)4–8 360 (25)
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
1 Silicon Carbide Carbon EPR 5SV
5 Carbon Silicon Carbide Viton
15
5SVB Series or 5SVD Series
2 10 40 3⁄16 24 5⁄8 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
3 15 11 13⁄16
4 15 11 13⁄16
5 20 40 11⁄16 11 13⁄16
6 25 11 13⁄16
7 25 11 13⁄16
8 30 49 3⁄4 11 13⁄16
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC
213TC (ODP) 230215TC (TEFC) 255215TC (ODP) 43 27 7⁄16 15 9⁄16 7 3⁄8 9 9⁄16 240254TC (TEFC) 49 15⁄16 30 5⁄16 19 5⁄8 8 15⁄16 11 1⁄2 370215TC (ODP) 43 27 7⁄16 15 9⁄16 7 3⁄8 9 9⁄16 250254TC (TEFC) 49 15⁄16 30 5⁄16 19 5⁄8 8 15⁄16 11 1⁄2 380254TC (ODP) 57 1⁄8 16 7⁄16 8 15⁄16 11 1⁄2 375256TC (TEFC) 60 11⁄16 20 9 5⁄8 12 5⁄16 435256TC (ODP) 61 1⁄2 43 1⁄2 18 8 5⁄16 11 1⁄2 395284TC (TEFC) 67 5⁄16 44 1⁄8 23 3⁄16 13 1⁄8 15 575256TC (ODP) 64 3⁄8 46 3⁄8 18 8 5⁄16 11 1⁄2 405284TC (TEFC) 69 7⁄8 46 11⁄16 23 3⁄16 13 1⁄8 15 585284TC (ODP) 70 1⁄8 20 3⁄8 12 1⁄4 13 1⁄4 490286TC (TEFC) 72 15⁄16 23 3⁄16 13 1⁄8 15 610
Stage
D1
D2
L3
L1
L2
1⁄2 DRAIN
FILLVENT*
85⁄8 101⁄4
85⁄8101⁄4
M19⁄16
4 HOLES
125⁄813⁄8
41⁄8
4 OR MORE STAGES21⁄ 2250 LB. IRON FLANGE300 LB. 316SS FLANGE
2 OR 3 STAGES21⁄ 2125 LB. IRON FLANGE150 LB. 316SS FLANGE
45°
CONDUIT BOX POSITIONONLY FOR MOTORNEMA FRAME 284TC-286TC
3⁄8 NPT3⁄8 NPT
*VENT 3⁄8 IRON OR 1⁄2 STEEL
5SV Dimensions and Weights(All dimensions are in inches, weights are total unit weight.)
16
0
100
200
300
400
500
0 100 150 250 300 US GPM
FE
ET
TO
TAL
DY
NA
MIC
HE
AD
CAPACITY
40
60
80
EF
F %
0
2
4
6
8
10
NP
SH
(ft)
6SV 60 Hz3450-3525 RPM
12
16
200
14
0
20
40
60
80
100
120
140
160
ME
TE
RS
0 30 40 50 60 70 80 m3/h2010
5020
4 Stage 20HP 3450RPM
3 Stage 15HP 3450RPM
5 Stage 25HP 3525RPM
2 Stage 10HP 3450RPM
NPSH
6SV 2 – 5 Stages Performance Curves
Construction: 304 or 316 stainless steelCapacities: 55– 340 gallons per minute (30– 77 m3/hr)Heads: 80– 420 feet TDH (25 –128 meters)Staging: 2– 5Minimum flow: 55 GPMMaximum working 175 PSI (12 bar) for the 6SVB orpressure: 275 psi (19 bar) for 6SVD.Temperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Solids handling: Although not recommended, the pumpmay pass a 3⁄8" sphere.
Design options: MaterialType 304 316 Stages Connections Location
6SVB x 2– 5 ANSI flange In-line6SVD x 2– 5 ANSI flange In-line
Piping Connections: Suction and discharge openings are 4".ANSI class 125 cast iron or class 150 steel flanges.
Component 304 316Materials Version Version
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 431 stainless steel 316 SS
Pump casing 304 stainless steel 316L SS
Intermediate crossover Cast iron Cast 316 SS
Seal housing Cast iron 316L SS
Inner bowls 316L stainless steel Same
Diffusers 316L stainless steel Same
Impellers 316L stainless steel Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Prime and drain plugs Nickel plated brass 316 SS
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast iron Same
Pump body/base Cast iron Cast 316 SS
6SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 60 Hz, 3500 RPM,three phase 10 HP (208–230/460 V). 15 to 25 HP (230/460 V) 6 SVhorsepowers from 10 to 25. For other motor options, contact the factory.Above motors are 1.15 S.F.
Base Model: 6SV 2 – 5 StagesGeneral Pump Description
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
1 Silicon Carbide Carbon EPR5 Carbon Silicon Carbide Viton
6SV
17
0
100
200
300
400
500
0 100 150 250 400 US GPM
FE
ET
TO
TAL
DY
NA
MIC
HE
AD
CAPACITY
40
60
80E
FF
%0
2
4
6
8
10
NP
SH
(ft)
6SV 60 Hz3525 RPM
12
16
200
14
0
20
40
60
80
100
120
140
160
ME
TE
RS
0 40 60 80 100 m3/h20
5020
300 350
600
700
800240
180
220
200
8 Stage 50HP
7 Stage 40HP
6 Stage 40HP
NPSH
6SV 6 – 8 Stages Performance Curves
Construction: 304 or 316 stainless steelCapacities: 55– 340 gallons per minute (30– 77 m3/hr)Heads: 230– 690 feet TDH (52 –157 meters)Staging: 6 – 8Minimum flow: 55 GPMMaximum working 360 PSI (25 bar)pressure:Temperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Solids handling: Although not recommended, the pumpmay pass a 3⁄8" sphere.
Design options: MaterialType 304 316 Stages Connections Location
6SVB x 6 – 8 ANSI flange In-line6SVD x 7– 8 ANSI flange In-line
Piping Connections: Suction and discharge openings are 21⁄2".ANSI class 250 cast iron or class 300 steel flanges.
Component 304 316Materials Version Version
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 431 stainless steel 316 SS
Pump casing 304 stainless steel 316L SS
Intermediate crossover Cast iron Cast 316 SS
Seal housing Cast iron 316L SS
Inner bowls 316L stainless steel Same
Diffusers 316L stainless steel Same
Impellers 316L stainless steel Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Prime and drain plugs Nickel plated brass 316 SS
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast iron Same
Pump body/base Cast iron Cast 316 SS
6SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 60 Hz, 3500 RPM,three phase. 30 to 50 HP (230/460 V) 6 SV horsepowers from 30 to 50. Forother motor options, contact the factory. Above motors are 1.15 S.F.
Base Model: 6SV 6 – 8 StagesGeneral Pump Description
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
1 Silicon Carbide Carbon EPR5 Carbon Silicon Carbide Viton
6SV
18
6SVB Series or 6SVD Series 2 – 5 Stages Stage
(All dimensions are in inches, weights are total unit weight.)
D1
D2
L3
L1
L2
1⁄2 DRAIN
FILLVENT*
85⁄8 101⁄4
85⁄8101⁄4
M1
143⁄831⁄8
51⁄2
125 LB. IRON FLANGE
45°
CONDUIT BOX POSITIONONLY FOR MOTORNEMA FRAME 284TC
3 ⁄8 NPT
4
9⁄16
4 HOLES
150 LB. 316SS FLANGE
3 ⁄8 NPT
*VENT 3⁄8 IRON OR 1⁄2 STEEL
6SV Dimensions and Weights
2 10 42 1⁄8 26 9⁄16 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
3 15 29 7⁄16 11 13⁄16
4 20 32 1⁄4 11 13⁄16
5 25 11 13⁄16
6SVB Series or 6SVD Series 6 – 8 Stages
D1
D2
L3
L1
L2
1⁄2 DRAIN
FILLVENT*
85⁄8 101⁄4
85⁄8101⁄4
M19⁄16
4 HOLES
125⁄813⁄8
41⁄8
21⁄ 2250 LB. IRON FLANGE300 LB. 316SS FLANGE
45°
CONDUIT BOX POSITIONONLY FOR MOTORNEMA FRAME 284TC-286TC
3⁄8 NPT3⁄8 NPT
*VENT 3⁄8 IRON OR 1⁄2 STEEL
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC
213TC (ODP) 240215TC (TEFC) 265215TC (ODP) 45 15 9⁄16 7 3⁄8 9 9⁄16 250254TC (TEFC) 49 1⁄16 19 5⁄8 8 15⁄16 11 1⁄2 385254TC (ODP) 48 11⁄16 16 7⁄16 8 15⁄16 11 1⁄2 355256TC (TEFC) 52 1⁄4 20 9 5⁄8 12 5⁄16 415256TC (ODP) 60 5⁄8 42 5⁄8 18 8 5⁄16 11 1⁄2 400284TC (TEFC) 66 7⁄16 43 1⁄4 23 3⁄16 13 1⁄8 15 580
StageMotor Dimensions (max.) Wt. (lbs.)
Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC256TC (ODP) 61 1⁄2 43 1⁄2 18 12 1⁄4 13 1⁄4 490284TC (TEFC) 67 5⁄16 44 1⁄8 23 3⁄16 13 1⁄8 15 605284TC (ODP) 65 7⁄8 19 3⁄16 12 1⁄3 13 1⁄4 503284TC (TEFC) 69 13⁄16 23 1⁄8 13 1⁄8 15 5⁄16 618
8 286TC (ODP) 50 69 3⁄16 49 3⁄4 19 7⁄16 12 19⁄64 13 1⁄4 11 13⁄16 517
6 30 11 13⁄16
7 40 46 11⁄16 11 13⁄16
19
Base Models: 5SV and6SV Major Components
1 Standard NEMA vertical motor
2 Rigid coupling
3 Motor adapter
4 Coupling guard
5 Seal housing
6 Mechanical seal
7 Stainless steel fill and drain plugs
8 Tie-rods
9 O-ring
10 Stainless steel pump casing
11 Intermediate crossover stage
12 Stainless steel diffuser
13 Stainless steel impeller
14 Tungsten carbide shaft sleeve
15 Ceramic bushing
16 Stainless steel shaft
17 Pump body
1
3
2
6
810
13
14
15
12
95
164
17
7
7
11
9
9
9
In-line ANSI connections
In-line ANSI connections
1
3
2
6
810
13
14
15
12
95
164
17
7
7
9
1–4 Stage
5–6 Stage
FPO
20
1SV 50 Hz Performance Curves
0
80
120
200
220
240
0 2 3 4 5
US GPM
H(ft)
TOTA
L D
YN
AM
IC H
EA
D
CAPACITY
0
40
60
EF
F %
2601SV 50 Hz2900 RPM
2
3
4
NPSH(m)
0 10 20 40 60 70
Q (m3/h)
0
100
200
300
400
500
600
700
800
H(m)
180
160
140
100
60
40
20
20
1
5030 Q (l/min)
.30η (%)
.20
.15
.10
.05
0
p (kW)
0 10 15 20
0 5 10 15
5
IMP GPM
24 Stage 5HP
11 Stage 11⁄2HP
22 Stage 3HP20 Stage 3HP18 Stage 3HP
16 Stage 3HP
14 Stage 2HP
12 Stage 2HP
9 Stage 11⁄2HP
7 Stage 1HP6 Stage 3⁄4HP5 Stage 3⁄4HP4 Stage 1⁄2HP
2 Stage 1⁄2HP
3 Stage 1⁄2HP
8 Stage 11⁄2HP
NPSH
ηPst
call for availablity on 50 Hz only staging
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 50 Hz motors are2900 RPM with 1.25 S.F.
Construction: 304 or 316 stainless steelCapacities: 3– 18 gallons per minute (.6 – 4.2 m3/hr)Heads: 23 – 804 feet TDH (7– 245 meters)Staging: 2– 24Minimum flow: 3 GPMMaximum working 230 PSI (16 bar) for the NPT version andpressure: 360 PSI (25 bar) for the ANSI flange versionTemperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
1SVA x 2–16 NPT In-line1SVB x 2– 24 ANSI flange In-line1SVC x 5 –16 ANSI flange Top/bottom1SVD x 2– 24 ANSI flange In-line
Piping Connections: Suction and discharge openings are 1" NPT.ANSI flanges are class 300, 11⁄4" flanges. Victaulic are 11⁄4".
Solids handling: Although not recommended, the pumpmay pass a 1⁄32" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O-rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plugs 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast aluminum Same
Pump base Aluminum casting Same
Base Model: 1SV, 50 HzGeneral Pump Description
1SV Motors
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 1SV
5 Carbon Silicon Carbide Viton
21
1SV, 50 Hz Dimensions and Weights
1SVA Series
1SVC Series
(All dimensions are in inches, weights are total unit weight.)
11⁄4
D1
D2
L3
L1
L2
3
415⁄163⁄8 DRAIN
3⁄8FILL VENT
M1
71⁄1685⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
1
L4
300 LB. FLANGE
CAPACITORCOVER ONSINGLE PHASEONLY
1 NPT
D1
D2
L3
L1
L2
2
65⁄16
3⁄8 DRAIN
3⁄8FILL VENT
3⁄82 HOLES
3⁄4
M1
71⁄16 85⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
CAPACITORCOVER ONSINGLE PHASEONLY
1SVB Series or 1SVD Series
M1
71⁄16 85⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
11⁄4
300 LB. FLANGE
D1
D2
L3
L1
L2
3
197⁄8
3⁄8 DRAIN
3⁄8FILL VENT
CAPACITORCOVER ONSINGLE PHASEONLY
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
21 1⁄2 9 13⁄16 4 3⁄8 4 15⁄16 4721 5⁄8 9 15⁄16 4 1⁄2 5 1⁄8 5122 1⁄2 9 13⁄16 4 3⁄8 4 15⁄16 5222 5⁄8 9 15⁄16 4 1⁄2 5 1⁄8 5623 7⁄16 9 13⁄16 4 3⁄8 5 5⁄8 5723 9⁄16 9 15⁄16 4 1⁄2 5 1⁄8 6125 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 69
25 13⁄16 11 3⁄16 5 1⁄4 5 9⁄16 6 5⁄8 8226 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 74
26 13⁄16 11 3⁄16 5 1⁄4 5 9⁄16 6 5⁄8 9227 7⁄8 11 1⁄4 5 5⁄8 78
27 13⁄16 11 3⁄16 5 9⁄16 8328 13⁄16 11 1⁄4 5 5⁄8 8329 5⁄8 12 1⁄16 5 9⁄16 113
29 13⁄16 11 1⁄4 5 5⁄8 8830 5⁄8 12 1⁄16 5 9⁄16 11831 3⁄4 11 1⁄4 5 5⁄8 9332 9⁄16 12 1⁄16 5 9⁄16 12333 11⁄16 12 3⁄16 5 5⁄8 9833 9⁄16 12 1⁄16 5 9⁄16 12035 11⁄16 12 3⁄16 5 5⁄8 10835 9⁄16 12 1⁄16 5 9⁄16 13037 1⁄2 12 71⁄16 13440 9⁄16 15 1⁄16 7 1⁄16 164
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 L4 M1 M2 D1 D2 ODP TEFC
26 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 6511 3⁄16 11 3⁄16 5 1⁄4 5 1⁄8 6 5⁄8 7027 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 5 11⁄16 7011 3⁄16 11 3⁄16 5 1⁄4 5 1⁄8 6 5⁄8 8028 13⁄16 11 1⁄4 5 5⁄8 7011 3⁄16 11 3⁄16 5 9⁄16 8029 13⁄16 11 1⁄4 5 5⁄8 8012 1⁄16 12 1⁄16 5 9⁄16 10530 13⁄16 11 1⁄4 5 5⁄8 8012 1⁄16 12 1⁄16 5 9⁄16 10533 11⁄16 12 3⁄16 5 5⁄8 9033 9⁄16 12 1⁄16 5 9⁄16 11535 11⁄16 12 3⁄16 5 5⁄8 10035 9⁄16 12 1⁄16 5 9⁄16 12537 1⁄2 12 11540 9⁄16 15 1⁄16 125
Stage
Stage
Stage
5 56C 3⁄4 15 5⁄8 8 7⁄8 6 3⁄4
6 56C 3⁄4 16 5⁄8 9 7⁄8 6 3⁄4
7 56C 1 17 9⁄16 10 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 1 1⁄2 18 9⁄16 11 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 1 1⁄2 19 9⁄16 12 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
12 56C 2 21 1⁄2 14 3⁄4 5 1⁄4 6 5⁄8 6 3⁄4
14 56C 2 23 1⁄2 17 3⁄16 5 1⁄4 6 5⁄8 6 3⁄4
16 184TC 3 25 1⁄2 19 11⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
2 56C 1⁄2 12 11⁄16 5 11⁄16 6 3⁄4
3 56C 1⁄2 13 5⁄8 5 11⁄16 6 3⁄4
4 56C 1⁄2 14 5⁄8 5 11⁄16 6 3⁄4
5 56C 3⁄4 15 5⁄8 6 3⁄4
6 56C 3⁄4 16 5⁄8 6 5⁄8 6 3⁄4
7 56C 1 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 1 1⁄2 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 1 1⁄2 19 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 1 1⁄2 20 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
12 56C 2 21 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
14 56C 2 23 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
16 184TC 3 26 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
18 184TC 3 28 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
20 184TC 3 30 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
22 184TC 3 32 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
24 184TC 5 34 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
2 56C 1⁄2 11 11⁄16 5 11⁄16 6 3⁄4
3 56C 1⁄2 12 11⁄16 5 11⁄16 6 3⁄4
4 56C 1⁄2 13 5⁄8 5 11⁄16 6 3⁄4
5 56C 3⁄4 14 5⁄8 6 3⁄4
6 56C 3⁄4 15 5⁄8 6 3⁄4
7 56C 1 16 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 1 1⁄2 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 1 1⁄2 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 1 1⁄2 20 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
12 56C 2 21 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
14 56C 2 23 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
16 184TC 3 25 1⁄2 5 7⁄8 7 7⁄8 11 13⁄16
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
22 1⁄2 9 13⁄16 4 3⁄8 4 15⁄16 4722 5⁄8 9 15⁄16 4 1⁄2 5 1⁄8 5123 7⁄16 9 13⁄16 4 3⁄8 4 15⁄16 5223 9⁄16 9 15⁄16 4 1⁄2 5 1⁄8 5624 7⁄16 9 13⁄16 4 3⁄8 4 15⁄16 5724 9⁄16 9 15⁄16 4 1⁄2 5 1⁄8 6126 1⁄4 10 5⁄8 4 3⁄8 4 15⁄16 6 11⁄16 69
26 13⁄16 11 3⁄16 5 1⁄4 5 9⁄16 6 5⁄8 8227 1⁄4 10 5⁄8 4 3⁄8 5 5⁄8 74
27 13⁄16 11 3⁄16 5 1⁄4 5 9⁄16 9228 13⁄16 11 1⁄4 5 5⁄8 7828 3⁄4 11 3⁄16 5 9⁄16 83
29 13⁄16 11 1⁄4 5 5⁄8 8330 5⁄8 12 1⁄16 5 9⁄16 113
30 13⁄16 11 1⁄4 5 5⁄8 8831 5⁄8 12 1⁄16 5 9⁄16 11831 3⁄4 11 1⁄4 5 5⁄8 9332 9⁄16 12 1⁄16 5 9⁄16 12333 11⁄16 12 3⁄16 5 5⁄8 9833 9⁄16 12 1⁄16 5 9⁄16 12035 11⁄16 12 3⁄16 5 5⁄8 10835 9⁄16 12 1⁄16 5 9⁄16 13038 7⁄16 12 13441 1⁄2 15 1⁄16 16440 7⁄16 12 12543 1⁄2 15 1⁄16 13542 7⁄16 12 13545 1⁄2 15 1⁄16 14544 7⁄16 12 14547 1⁄2 15 1⁄16 15546 7⁄16 12 16049 1⁄2 15 1⁄16 170
22
2SV, 50 Hz Performance Curves
0
80
120
200
220
240
0 2 4 6 8
US GPM
H(ft)
TOTA
L D
YN
AM
IC H
EA
D
CAPACITY
0
40
80
EF
F %
260
2SV 50 Hz2900 RPM
1
3
4
NPSH(m)
0 25 75 125 150
Q (m3/h)
0
100
200
300
400
500
600
700
800
H(m)
180
160
140
100
60
40
20
20
10050 Q (l/min)
.24η (%)
.20
.16
.12
.08
p (kW)
0 20 30
0 10 20 30
10
IMP GPM
24 Stage 5HP
8 Stage 11⁄2HP
22 Stage 5HP20 Stage 5HP18 Stage 3HP16 Stage 3HP14 Stage 3HP13 Stage 3HP
7 Stage 11⁄2HP6 Stage 1HP
4 Stage 3⁄4HP
2 Stage 1⁄2HP
3 Stage 1⁄2HP
NPSH
η
Pst
60
2
9 Stage 2HP
5 Stage 1HP
11 Stage 2HP
call for availablity on 50 Hz only staging
Construction: 304 or 316 stainless steelCapacities: 6– 35 gallons per minute (1.3 – 8 m3/hr)Heads: 16 – 732 feet TDH (5 – 223 meters)Staging: 2– 24Minimum flow: 6 GPMMaximum working 230 PSI (16 bar) for the NPT version andpressure: 360 PSI (25 bar) for the ANSI flange versionTemperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
2SVA x 2–16 NPT In-line2SVB x 2– 24 ANSI flange In-line2SVC x 5–14 ANSI flange Top/bottom2SVD x 2– 24 ANSI flange In-line
Piping Connections: Suction and discharge openings are 11⁄4" NPT.ANSI flanges are class 300, 11⁄4" flanges. Victaulic are 11⁄4".
Solids handling: Although not recommended, the pumpmay pass a 1⁄16" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O- rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plugs 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast aluminum Same
Pump base Cast aluminum Same
2SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 50 Hz motors are2900 RPM with 1.25 S.F.
Base Model: 2SV, 50 HzGeneral Pump Description
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 2SV
5 Carbon Silicon Carbide Viton
23
(All dimensions are in inches, weights are total unit weight.)
2SVA Series
2SVC Series
2SV, 50 Hz Dimensions and Weights
11⁄4
D1
D2
L3
L1
L2
3
415⁄163⁄8 DRAIN
3⁄8FILL VENT
M1
71⁄1685⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
1
L4
300 LB. FLANGE
CAPACITORCOVER ONSINGLE PHASEONLY
11⁄4 NPT
D1
D2
L3
L1
L2
2
65⁄16
3⁄8 DRAIN
3⁄8FILL VENT
3⁄82 HOLES
3⁄4
M1
71⁄16 85⁄16
315⁄16
55⁄16
M2
1⁄24 HOLES
CAPACITORCOVER ONSINGLE PHASEONLY
2SVB Series or 2SVD Series
M1
71⁄16 85⁄16
315⁄16
57⁄8
M2
1⁄24 HOLES
11⁄4
300 LB. FLANGE
D1
D2
L3
L1
L2
3
197⁄8
3⁄8 DRAIN
3⁄8FILL VENT
CAPACITORCOVER ONSINGLE PHASEONLY
55⁄16
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 L4 M1 M2 D1 D2 ODP TEFC
26 7⁄8 11 1⁄4 5 5⁄8 7011 3⁄16 11 3⁄16 5 9⁄16 7527 7⁄8 11 1⁄4 5 5⁄8 7011 3⁄16 11 3⁄16 5 9⁄16 8028 13⁄16 11 1⁄4 5 5⁄8 8012 1⁄16 12 1⁄16 5 9⁄16 10029 13⁄16 11 1⁄4 5 5⁄8 8012 1⁄16 12 1⁄16 5 9⁄16 10531 3⁄4 12 3⁄16 5 5⁄8 8012 1⁄16 12 1⁄16 5 9⁄16 10533 11⁄16 12 3⁄16 5 5⁄8 11012 1⁄16 12 1⁄16 5 9⁄16 12035 1⁄2 12 11038 9⁄16 15 1⁄16 12036 1⁄2 12 11039 9⁄16 15 1⁄16 125
5 56C 1 15 5⁄8 8 7⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 1 16 5⁄8 9 7⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 1 1⁄2 17 9⁄16 10 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 1 1⁄2 18 9⁄16 11 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 2 19 9⁄16 12 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 2 21 1⁄2 14 3⁄4 5 1⁄4 6 5⁄8 6 3⁄4
13 184TC 3 23 1⁄2 16 3⁄4 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
14 184TC 3 24 1⁄2 18 11⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
Stage
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
21 1⁄2 9 13⁄16 5 5⁄8 4521 5⁄8 9 15⁄16 5 9⁄16 5022 1⁄2 9 13⁄16 5 5⁄8 5522 5⁄8 9 15⁄16 5 9⁄16 6524 1⁄4 10 5⁄8 5 5⁄8 65
24 13⁄16 11 3⁄16 5 9⁄16 6525 7⁄8 11 1⁄4 5 5⁄8 70
25 13⁄16 11 3⁄16 5 9⁄16 7526 7⁄8 11 1⁄4 5 5⁄8 70
26 13⁄16 11 3⁄16 5 9⁄16 8027 7⁄8 11 1⁄4 5 5⁄8 80
28 11⁄16 12 1⁄16 5 9⁄16 10028 13⁄16 11 1⁄4 5 5⁄8 8029 5⁄8 12 1⁄16 5 9⁄16 10530 3⁄4 12 3⁄16 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 10532 3⁄4 12 3⁄16 5 5⁄8 8032 5⁄8 12 1⁄16 5 9⁄16 10534 1⁄2 12 8037 9⁄16 15 1⁄16 10535 1⁄2 12 8038 9⁄16 15 1⁄16 10537 1⁄2 12 8040 9⁄16 15 1⁄16 105
Stage
2 56C 1⁄2 11 11⁄16 5 1⁄4 6 5⁄8 6 3⁄4
3 56C 1⁄2 12 11⁄16 5 1⁄4 6 5⁄8 6 3⁄4
4 56C 3⁄4 13 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
5 56C 1 14 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 1 15 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 1 1⁄2 16 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 1 1⁄2 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 2 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 2 20 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
13 184TC 3 22 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
14 184TC 3 23 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
16 184TC 3 25 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 M2 D1 D2 ODP TEFC
22 1⁄2 9 13⁄16 5 5⁄8 4522 5⁄8 9 15⁄16 5 9⁄16 5023 7⁄16 9 13⁄16 5 5⁄8 5523 9⁄16 9 15⁄16 5 9⁄16 6525 1⁄4 10 5⁄8 5 5⁄8 65
25 13⁄16 11 3⁄16 5 9⁄16 6526 7⁄8 11 1⁄4 5 5⁄8 70
26 13⁄16 11 3⁄16 5 9⁄16 7527 7⁄8 11 1⁄4 5 5⁄8 70
27 13⁄16 11 3⁄16 5 9⁄16 8028 13⁄16 11 1⁄4 5 5⁄8 8029 5⁄8 12 1⁄16 5 9⁄16 100
29 13⁄16 11 1⁄4 5 5⁄8 8030 5⁄8 12 1⁄16 5 9⁄16 10531 3⁄4 12 3⁄16 5 5⁄8 8031 5⁄8 12 1⁄16 5 9⁄16 105
33 11⁄16 12 3⁄16 5 5⁄8 11033 9⁄16 12 1⁄16 5 9⁄16 12035 1⁄2 12 11038 9⁄16 15 1⁄16 12036 1⁄2 12 11039 9⁄16 15 1⁄16 12538 7⁄16 12 12541 1⁄2 15 1⁄16 13540 7⁄16 12 12543 1⁄2 15 1⁄16 13542 7⁄16 12 13545 1⁄2 15 1⁄16 14544 7⁄16 12 14547 1⁄2 15 1⁄16 15546 7⁄16 12 16049 1⁄2 15 1⁄16 170
2 56C 1⁄2 12 11⁄16 5 1⁄4 6 5⁄8 6 3⁄4
3 56C 1⁄2 13 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
4 56C 3⁄4 14 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
5 56C 1 15 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
6 56C 1 16 5⁄8 5 1⁄4 6 5⁄8 6 3⁄4
7 56C 1 1⁄2 17 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
8 56C 1 1⁄2 18 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
9 56C 2 19 9⁄16 5 1⁄4 6 5⁄8 6 3⁄4
11 56C 2 21 1⁄2 5 1⁄4 6 5⁄8 6 3⁄4
13 184TC 3 23 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
14 184TC 3 24 1⁄2 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
16 184TC 3 26 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
18 184TC 3 28 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
20 184TC 5 30 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
22 184TC 5 32 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
24 184TC 5 34 7⁄16 5 7⁄8 7 1⁄16 7 7⁄8 11 13⁄16
Stage
55⁄16
24
3SV, 50 Hz Performance Curves
0
80
120
200
220
0 2 4 10 14
USGPM
H(ft)
TOTA
L D
YN
AM
IC H
EA
D
CAPACITY
0
40
80
EF
F %
240
3SV 50 Hz2900 RPM
0
3
5
NPSH(m)
0 50 150 250
Q (m3/h)
0
100
200
300
400
500
600
700
H(m)
180
160
140
100
60
40
20
20
200100 Q (l/min)
.8η (%)
.6
.4
.2
0
p (kW)
0 20 70
0 10 20 50
10
IMP GPM
16 Stage 10HP
NPSH
η
Pst
60
2
1286
4
1
60504030
4030
14 Stage 71⁄2HP
12 Stage 71⁄2HP
11 Stage 71⁄2HP
9 Stage 5HP
8 Stage 5HP
2 Stage 11⁄2HP
3 Stage 11⁄2HP
6 Stage 5HP
5 Stage 3HP
4 Stage 2HP
call for availablity on 50 Hz only staging
Base Model: 3SV, 50 HzGeneral Pump Description
Construction: 304 or 316 stainless steelCapacities: 11– 62 gallons per minute (2.5–14 m3/hr)Heads: 46 –705 feet TDH (14 – 215 meters)Staging: 2–16Minimum flow: 11 GPMMaximum working 230 PSI (16 bar) for the NPT version andpressure: 360 PSI (25) for the ANSI flange versionTemperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
3SVA x 2 – 11 NPT In-line3SVB x 2–16 ANSI flange In-line3SVC x 5–12 ANSI flange Top/bottom3SVD x 2–16 ANSI flange In-line
Piping Connections: Suction and discharge openings are 11⁄2" NPT.ANSI flanges are class 300, 2" flanges. Victaulic are 2".
Solids handling: Although not recommended, the pumpmay pass a 1⁄8" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O-rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plug 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast aluminum below5 HP and cast iron5 HP and above Same
Pump base Cast aluminum Same
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 50 Hz motors are2900 RPM with 1.25 S.F.
3SV Motors
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 3SV
5 Carbon Silicon Carbide Viton
25
D1
D2
L3
L1
L2
3⁄8 DRAIN
3⁄8FILL VENT
M2
815⁄32 95⁄8
51⁄871⁄2
M11⁄2
4 HOLES
1
31⁄8
77⁄8
15⁄322 HOLES
11⁄2 NPT
CAPACITORCOVER ONSINGLEPHASEONLY
3SVA Series
3SVC Series
(All dimensions are in inches, weights are total unit weight.)
2
D1
D2
L3
L1
L2
515⁄16 3⁄8 DRAIN
3⁄8FILL VENT
M1
815⁄3295⁄8
51⁄871⁄2
M2
1⁄24 HOLES
L4
300 LB. FLANGE
13⁄16
39⁄16
CAPACITORCOVER ONSINGLEPHASE ONLY
3SVB Series or 3SVD Series
2
D1
D2
L3
L1
L2
1113⁄16
3⁄8 DRAIN
3⁄8FILL VENT
M2
815⁄32 95⁄8
51⁄871⁄2
M11⁄2
4 HOLES
300 LB. FLANGE
13⁄16
39⁄16
CAPACITORCOVER ONSINGLE PHASEONLY
3SV, 50 Hz Dimensions and Weights
2 56C 1 1⁄2 15 5⁄16 5 1⁄4 6 5⁄8 6 3⁄4
3 56C 1 1⁄2 16 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
4 56C 2 18 5⁄16 5 1⁄4 6 5⁄8 6 3⁄4
5 184TC 3 19 13⁄16 5 7⁄8 7 7⁄8 11 13⁄16
6 184TC 5 22 13⁄16 5 7⁄8 7 7⁄8 11 13⁄16
8 184TC 5 24 1⁄4 5 7⁄8 7 7⁄8 11 13⁄16
9 7 1⁄2 25 3⁄8 7 3⁄8 9 9⁄16 11 13⁄16
11 7 1⁄2 25 3⁄4 7 3⁄8 9 9⁄16 11 13⁄16
Stage
StageMotor Dimensions (max.) Wt. (lbs.)
Frame HP L1 L2 L3 L4 M1 D1 D2 ODP TEFC31 13⁄16 12 11515 1⁄16 15 1⁄16 13034 13⁄16 12 12515 1⁄16 15 1⁄16 13536 1⁄4 12 13015 1⁄16 15 1⁄16 135
213JM 175215JM 200213JM 175215JM 200213JM 185215JM 315
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC
26 9⁄16 11 1⁄4 7512 1⁄16 12 1⁄16 8528 1⁄16 11 1⁄4 8512 1⁄16 12 1⁄16 11030 1⁄2 12 3⁄16 11512 1⁄16 12 1⁄16 12531 13⁄16 12 11515 1⁄16 15 1⁄16 13034 13⁄16 12 12515 1⁄16 15 1⁄16 13536 1⁄4 12 12515 1⁄16 15 1⁄16 135
213JM 175215JM 200213JM 175215JM 200213JM 185215JM 315215JM 50 1⁄16 15 9⁄16 7 3⁄8 9 9⁄16 190254JM 54 1⁄8 19 5⁄8 8 15⁄16 11 1⁄2 325215JM 48 1⁄4 15 9⁄16 7 3⁄8 9 9⁄16 210254JM 52 5⁄16 19 5⁄8 8 15⁄16 11 1⁄2 335
Stage
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC
26 9⁄16 11 1⁄4 7512 1⁄16 12 1⁄16 8528 1⁄16 11 1⁄4 8512 1⁄16 12 1⁄16 11030 1⁄2 12 3⁄16 11512 1⁄16 12 1⁄16 12531 13⁄16 12 11515 1⁄16 15 1⁄16 13034 13⁄16 12 12515 1⁄16 15 1⁄16 13536 1⁄4 12 13015 1⁄16 15 1⁄16 135
213JM 40 15⁄16 15 9⁄16 135215JM 40 15⁄16 15 9⁄16 140213JM 41 5⁄16 15 9⁄16 145215JM 41 5⁄16 15 9⁄16 150
2 56C 1 1⁄2 15 5⁄16 5 1⁄4 6 5⁄8 6 3⁄4
3 56C 1 1⁄2 16 13⁄16 5 1⁄4 6 5⁄8 6 3⁄4
4 56C 2 18 5⁄16 5 1⁄4 6 5⁄8 6 3⁄4
5 184TC 3 19 13⁄16 5 7⁄8 7 7⁄8 11 13⁄16
6 184TC 5 22 13⁄16 5 7⁄8 7 7⁄8 11 13⁄16
8 184TC 5 24 1⁄4 5 7⁄8 7 7⁄8 11 13⁄16
9 7 1⁄2 40 15⁄16 25 3⁄8 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
11 7 1⁄2 41 5⁄16 25 3⁄4 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
12 7 1⁄2 41 5⁄16 25 3⁄4 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
14 10 34 1⁄2 11 13⁄16
16 10 32 11⁄16 11 13⁄16
5 184TC 3 19 13⁄16 12 11⁄16 5 7⁄8 7 7⁄8 11 13⁄16
6 184TC 5 22 13⁄16 15 11⁄16 5 7⁄8 7 7⁄8 11 13⁄16
8 184TC 5 24 1⁄4 17 3⁄16 5 7⁄8 7 7⁄8 11 13⁄16
9 7 1⁄2 40 15⁄16 25 3⁄8 15 9⁄16 20 3⁄16 7 3⁄8 9 9⁄16 11 13⁄16
11 7 1⁄2 41 5⁄16 25 3⁄4 15 9⁄16 21 11⁄16 7 3⁄8 9 9⁄16 11 13⁄16
12 7 1⁄2 41 5⁄16 25 3⁄4 15 9⁄16 24 5⁄8 7 3⁄8 9 9⁄16 11 13⁄16
26
4SV, 50 Hz Performance Curves
0
80
120
200
220
0 15 25
US GPM
H(ft)
TOTA
L D
YN
AM
IC H
EA
D
CAPACITY
30
50
70
EF
F %
2604SV 50 Hz2900 RPM
0
3
5
NPSH(m)
0 200 400
Q (m3/h)
0
100
200
300
400
500
600
800
H(m)
180
160
140
100
60
40
20
40
300100 Q (l/min)
1.2η (%)
1
.8
.6
.4
p (kW)
0 20 100
0 20 80 IMP GPM
15 Stage 20HP
NPSH
η
Pst
60
2
20105
4
1
806040
6040
14 Stage 15HP
7 Stage 71⁄2HP
6 Stage 71⁄2HP
8 Stage 10HP
4 Stage 5HP
240
700
12 Stage 15HP
10 Stage 15HP
5 Stage 71⁄2HP
3 Stage 3HP
2 Stage 2HP
call for availablity on 50 Hz only staging
Construction: 304 or 316 stainless steelCapacities: 17–106 gallons per minute (4– 24 m3/hr)Heads: 50– 840 feet TDH (15– 256 meters)Staging: 2–15Minimum flow: 17 GPMMaximum working 360 PSI (25 bar)pressure:Temperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Design options: MaterialType 304 316 Stages Connections Location
4SVB x 2–15 ANSI flange In-line4SVC x 4–10 ANSI flange Top/bottom4SVD x 2–15 ANSI flange In-line
Piping Connections: Suction and discharge openings are 2" ANSIclass 300 flanges. Victaulic are 2".
Solids handling: Although not recommended, the pumpmay pass a 3⁄16" sphere.
Component 304 316Materials Version Version
Pump body 304 stainless steel 316L SS
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 304 stainless steel 316L SS
Pump casing 304 stainless steel 316L SS
Top seal housing 304 stainless steel 316L SS
Inner bowls 304 stainless steel 316L SS
Diffusers 304 stainless steel 316L SS
Impellers 316L stainless steel Same
Impeller O-rings Viton Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Priming and drain plug 316L stainless steel Same
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast iron Same
Pump base Cast aluminum Same
4SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 50 Hz motors are2900 RPM with 1.25 S.F.
Base Model: 4SV, 50 HzGeneral Pump Description
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
2 Tungsten Carbide Carbon EPR
3 Tungsten Carbide Carbon Viton 4SV
5 Carbon Silicon Carbide Viton
27
4SV, 50Hz Dimensions and Weights
4SVB Series or 4SVD Series
(All dimensions are in inches, weights are total unit weight.)
4SVC Series
2
D1
D2
L3
L1
L2
515⁄16 3⁄8 DRAIN
3⁄8FILL VENT
M1
815⁄3295⁄8
51⁄871⁄2
1⁄24 HOLES
L4
300 LB. FLANGE
13⁄16
39⁄16
2
D1
D2
L3
L1
L2
1113⁄16
3⁄8 DRAIN
3⁄8FILL VENT
M2
815⁄32 95⁄8
51⁄871⁄2
M11⁄2
4 HOLES
300 LB. FLANGE
13⁄16
39⁄16
CAPACITORCOVER ONSINGLE PHASEONLY
3 184TC 3 17 1⁄4 5 7⁄8 7 7⁄8 11 13⁄16
4 184TC 5 18 3⁄4 5 7⁄8 7 7⁄8 11 13⁄16
5 7 1⁄2 21 7⁄16 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
6 & 7 7 1⁄2 24 7⁄16 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
8 10 25 15⁄16 11 13⁄16
10 15 28 7⁄8 11 13⁄16
12 15 26 7⁄16 11 13⁄16
14 15 28 7⁄16 11 13⁄16
Stage
StageMotor Dimensions (max.) Wt. (lbs.)
Frame HP L1 L2 L3 L4 M1 D1 D2 ODP TEFC30 3⁄4 12 1203313⁄16 15 1⁄16 125
213TC 37 165215TC 21 7⁄16 185213TC 40 170215TC 24 7⁄16 300215TC 41 1⁄2 15 9⁄16 7 3⁄8 9 9⁄16 175254TC 45 9⁄16 19 5⁄8 8 15⁄16 11 1⁄2 305254TC 45 5⁄16 16 7⁄16 8 15⁄16 11 1⁄2 275256TC 48 7⁄8 20 9 5⁄8 12 5⁄16 335
Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC
29 1⁄4 12 12032 5⁄16 15 1⁄16 12530 3⁄4 12 120
33 13⁄16 15 1⁄16 125213TC 37 165215TC 21 7⁄16 185213TC 40 170215TC 24 7⁄16 300215TC 41 1⁄2 15 9⁄16 7 3⁄8 9 9⁄16 175254TC 45 9⁄16 19 5⁄8 8 15⁄16 11 1⁄2 305254TC 45 5⁄16 16 7⁄16 8 15⁄16 11 1⁄2 275256TC 48 7⁄8 20 9 5⁄8 12 5⁄16 335254TC 42 7⁄8 16 7⁄16 8 15⁄16 11 1⁄2 280256TC 46 7⁄16 20 9 5⁄8 12 5⁄16 340254TC 44 7⁄8 16 7⁄16 8 15⁄16 11 1⁄2 285256TC 48 7⁄16 20 9 5⁄8 12 5⁄16 345
15 256TC 20 48 7⁄16 30 7⁄16 18 8 5⁄16 11 1⁄2 11 13⁄16 287
4 184TC 5 18 3⁄4 11 3⁄16 5 7⁄8 7 7⁄8 11 13⁄16
5 7 1⁄2 21 7⁄16 15 9⁄16 12 11⁄16 7 3⁄8 9 9⁄16 11 13⁄16
6 & 7 7 1⁄2 24 7⁄16 15 9⁄16 15 11⁄16 7 3⁄8 9 9⁄16 11 13⁄16
8 10 25 15⁄16 17 3⁄16 11 13⁄16
10 15 28 7⁄8 20 3⁄16 11 13⁄16
28
5SV, 50 Hz Performance Curves
5SV 50 Hz2900 RPM
0
80
120
200
220
0 25 40
US GPM
H(ft)
TOTA
L D
YN
AM
IC H
EA
D
CAPACITY
30
50
70
EF
F %
260
0
3
5
NPSH(m)
0 200 700
Q (m3/h)
0
100
200
300
400
500
600
800
H(m)
180
160
140
100
60
40
20
40
300100 Q (l/min)
3η (%)
2.5
2
1.5
1
p (kW)
0 150
0 150 IMP GPM
12 Stage 25HP
NPSH
η
Pst
60
2
35105
4
1
10050
10050
11 Stage 25HP
6 Stage 15HP
8 Stage 20HP
5 Stage 10HP
240
700
10 Stage 20HP
9 Stage 20HP
3 Stage 71⁄2HP
4 Stage 10HP
2 Stage 71⁄2HP
302015
600500400
0
15
10
5
NPSH(ft)
7 Stage 15HP
call for availablity on 50 Hz only staging
Base Model: 5SV, 50 HzGeneral Pump Description
Construction: 304 or 316 stainless steelCapacities: 26 –171 gallons per minute (6– 39 m3/hr)Heads: 50– 105 feet TDH (15 – 245 meters)Staging: 2– 12Minimum flow: 26 GPMMaximum workingpressure:
Temperatures: Standard liquid temperature from -13°F (-25°C) to250°F (120°C)
Solids handling: Although not recommended, the pumpmay pass a 3⁄16" sphere.
Design options: MaterialType 304 316 Stages Connections Location
5SVB x 2– 12 ANSI flange In-line5SVD x 2– 12 ANSI flange In-line
Piping Connections: Suction and discharge openings are 21⁄2". ANSI class125 cast iron (150 steel) flanges up to three stages andclass 250 cast iron (300 steel) for four stage and above.
Component 304 316Materials Version Version
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 431 stainless steel 316 SS
Pump casing 304 stainless steel 316L SS
Intermediate crossover Cast iron Cast 316 SS
Top seal housing Cast iron 316 SS
Inner bowls 316L stainless steel Same
Diffusers 316L stainless steel Same
Impellers 316L stainless steel Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316 stainless steel Same
Mechanical seal
Priming and drain plugs Nickel plated brass 316 SS
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast iron Same
Pump body/base Cast iron Cast 316 SS
5SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 50 Hz motors are2900 RPM with 1.25 S.F.
Material Maximum workingType 304 316 Stages pressure in psi. (Bar)
5SVB x 2– 3 175 (12)4–12 360 (25)
5SVD x 2– 3 275 (19)4–12 360 (25)
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
1 Silicon Carbide Carbon EPR 5SV
5 Carbon Silicon Carbide Viton
29
5SVB Series or 5SVD Series
(All dimensions are in inches, weights are total unit weight.)
D1
D2
L3
L1
L2
1⁄2 DRAIN
FILLVENT*
85⁄8 101⁄4
85⁄8101⁄4
M19⁄16
4 HOLES
125⁄813⁄8
41⁄8
4 OR MORE STAGES21⁄ 2250 LB. IRON FLANGE300 LB. 316SS FLANGE
2 OR 3 STAGES21⁄ 2125 LB. IRON FLANGE150 LB. 316SS FLANGE
45°
CONDUIT BOX POSITIONONLY FOR MOTORNEMA FRAME 284TC-286TC
3⁄8 NPT3⁄8 NPT
*VENT 3⁄8 IRON OR 1⁄2 STEEL
5SV, 50 Hz Dimensions and Weights
2 184TC 5 24 5⁄8 5 7⁄8 7 7⁄8 11 13⁄16
3 7 1⁄2 43 27 7⁄16 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
4 10 11 13⁄16
5 10 11 13⁄16
6 15 43 1⁄2 11 13⁄16
7 15 46 3⁄8 11 13⁄16
8 20 11 13⁄16
9 20 52 9⁄16 11 13⁄16
10 20 55 7⁄16 11 13⁄16
11 25 58 1⁄4 11 13⁄16
12 25 61 1⁄16 11 13⁄16
Motor Dimensions (max.) Wt. (lbs.)
Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC36 5⁄8 12 230
39 11⁄16 15 1⁄16 255213TC 240215TC 370215TC 43 27 7⁄16 15 9⁄16 7 3⁄8 9 9⁄16 250254TC 49 15⁄16 30 5⁄16 19 5⁄8 8 15⁄16 11 1⁄2 380215TC 53 3⁄8 37 13⁄16 15 9⁄16 7 3⁄8 9 9⁄16 375254TC 60 5⁄16 40 11⁄16 19 5⁄8 8 15⁄16 11 1⁄2 435254TC 59 15⁄16 16 7⁄16 8 15⁄16 11 1⁄2 395256TC 63 1⁄2 20 9 5⁄8 12 1⁄3 375254TC 62 13⁄16 16 7⁄16 8 15⁄16 11 1⁄2 405256TC 66 3⁄8 20 9 5⁄8 12 1⁄3 585256TC 64 7⁄8 46 7⁄8 18 9 5⁄8 12 1⁄3 490284TC 72 15⁄16 49 3⁄4 23 3⁄16 13 1⁄8 15 610256TC 70 9⁄16 18 8 5⁄16 11 1⁄2 495284TC 75 3⁄4 23 3⁄16 13 1⁄8 15 615256TC 73 7⁄16 18 8 5⁄16 11 1⁄2 500284TC 78 5⁄8 23 3⁄16 13 1⁄8 15 620284TC 78 5⁄8 20 3⁄8 12 1⁄4 13 1⁄4 505286TC 81 7⁄16 23 3⁄16 13 1⁄8 15 625284TC 81 7⁄16 20 3⁄8 12 1⁄4 13 1⁄4 510286TC 84 1⁄4 23 3⁄16 13 1⁄8 15 630
Stage
30
6SV, 50 Hz Performance Curves
1.5
6SV 50 Hz2900 RPM
0
80
120
0 50 80
US GPM
H(ft)
TOTA
L D
YN
AM
IC H
EA
D
CAPACITY
30
50
70
EF
F %
160
0
3
7
NPSH(m)
0 400 1400
Q (m3/h)
0
100
200
300
400
500H
(m)
140
100
60
40
20
40
600200 Q (l/min)
3.5η (%)
3
2.5
p (kW)
0 350
0 300 IMP GPM
8 Stage 25HP
NPSH
η
Pst
60
2
702010
4
1
100
100
7 Stage 20HP
4 Stage 15HP
5 Stage 15HP
2 Stage 71⁄2HP
604030
12001000800
0
20
10
5
NPSH(ft)
3 Stage 10HP
2
5
6
15
300250200150
25020015050
50
call for availablity on 50 Hz only staging
6 Stage 20HP
Construction: 304 or 316 stainless steelCapacities: 45– 317 gallons per minute (10– 72 m3/hr)Heads: 40– 640 feet TDH (12–145 meters)Staging: 2– 8Minimum flow: 45 GPMMaximum working 175 PSI (12 bar) for the 6SVB orpressure: 275 psi (19 bar) for 6SVD.Temperatures: Standard liquid temperature from -13°F (-25°C) to
250°F (120°C)
Solids handling: Although not recommended, the pumpmay pass a 3⁄8" sphere.
Design options: MaterialType 304 316 Stages Connections Location
6SVB x 2– 8 ANSI flange In-line6SVD x 2– 8 ANSI flange In-line
Piping Connections: Suction and discharge openings are 4".ANSI class 125 cast iron or class 150 steel flanges.
Component 304 316Materials Version Version
Casing O-rings Viton Same
Tie-rods and nuts Zinc-coated steel Same
Pump shaft 431 stainless steel 316 SS
Pump casing 304 stainless steel 316L SS
Intermediate crossover Cast iron Cast 316 SS
Seal housing Cast iron 316L SS
Inner bowls 316L stainless steel Same
Diffusers 316L stainless steel Same
Impellers 316L stainless steel Same
Shaft spacers 316L stainless steel Same
Shaft bushing Ceramic Same
Shaft sleeve Tungsten carbide Same
Seal spring and retainer clip 316L stainless steel Same
Mechanical seal
Prime and drain plugs Nickel plated brass 316 SS
NEMA motor adapter Cast iron Same
Coupling guards 304 stainless steel Same
Motor shaft coupling Cast iron Same
Pump body/base Cast iron Cast 316 SS
6SV Motors
Standard motors supplied by Goulds are NEMA standard TC frame motorsopen drip proof, or totally enclosed fan cooled enclosures. 50 Hz motors are2900 RPM with 1.25 S.F.
Base Model: 6SV, 50 HzGeneral Pump Description
Code No. Rotary Stationary Elastomers Where Found
0 Silicon Carbide Silicon Carbide Viton Stan. on all units
1 Silicon Carbide Carbon EPR5 Carbon Silicon Carbide Viton
6SV
31
6SVB Series or 6SVD Series 2 – 8 Stages
D1
D2
L3
L1
L2
1⁄2 DRAIN
FILLVENT*
85⁄8 101⁄4
85⁄8101⁄4
M1
143⁄831⁄8
51⁄2
125 LB. IRON FLANGE
45°
CONDUIT BOX POSITIONONLY FOR MOTORNEMA FRAME 284TC
3 ⁄8 NPT
4
9⁄16
4 HOLES
150 LB. 316SS FLANGE
3 ⁄8 NPT
*VENT 3⁄8 IRON OR 1⁄2 STEEL
6SV, 50 Hz Dimensions and Weights
Stage Motor Dimensions (max.) Wt. (lbs.)Frame HP L1 L2 L3 M1 D1 D2 ODP TEFC213TC 240215TC 265215TC 45 15 9⁄16 7 3⁄8 9 9⁄16 250254TC 49 1⁄16 19 5⁄8 8 15⁄16 11 1⁄2 385254TC 48 11⁄16 16 7⁄16 8 15⁄16 11 1⁄2 355256TC 52 1⁄4 20 9 5⁄8 12 5⁄16 415254TC 59 1⁄16 16 7⁄16 8 15⁄16 11 1⁄2 400256TC 62 5⁄8 20 9 5⁄8 12 5⁄16 580256TC 63 7⁄16 45 7⁄16 18 8 5⁄16 11 1⁄2 490284TC 68 5⁄8 46 1⁄16 23 3⁄16 13 1⁄8 15 605256TC 66 1⁄8 48 1⁄8 18 8 5⁄16 11 1⁄2 495284TC 71 5⁄16 48 7⁄8 23 3⁄16 13 1⁄8 15 610284TC 72 1⁄8 20 3⁄8 12 1⁄4 13 1⁄4 500286TC 74 15⁄16 23 3⁄16 13 1⁄8 15 615
2 7 1⁄2 42 1⁄8 26 9⁄16 15 9⁄16 7 3⁄8 9 9⁄16 11 13⁄16
3 10 29 7⁄16 11 13⁄16
4 15 32 1⁄4 11 13⁄16
5 15 42 5⁄8 11 13⁄16
6 20 11 13⁄16
7 20 11 13⁄16
8 25 51 3⁄4 11 13⁄16
32
1SVB/1SVD
1SVC
2SVA
2SVB/2SVD
2SVC
3SVA
3SVC
Horizontal Mounting Option
• Available for all six SSV sizes and all of their configurations.• Consists of SSV pump with base mounting foot and footed motor for horizontal installations.• Unit depicted may not show actual pump configuration. Use for mounting location only.
Motor PumpSeries A B C D E F G H Shim Shim
Thickness Thickness1SVA 56C 31⁄2 7 9 3⁄8 1 3 69⁄16 47⁄8 1 –
56C 31⁄2 7 9 13⁄8 1 3 69⁄16 47⁄8 1 –184TC 41⁄2 7 9 13⁄8 1 51⁄2 85⁄8 71⁄2 – –56C 31⁄2 101⁄2 12 13⁄8 1 3 69⁄16 47⁄8 1 –
184TC 41⁄2 101⁄2 12 13⁄8 1 51⁄2 85⁄8 71⁄2 – –56C 31⁄2 7 9 3⁄8 1 3 69⁄16 47⁄8 1 –
184TC 41⁄2 7 9 3⁄8 1 51⁄2 85⁄8 71⁄2 – –56C 31⁄2 7 9 13⁄8 1 3 69⁄16 47⁄8 1 –
184TC 41⁄2 7 9 13⁄8 1 51⁄2 85⁄8 71⁄2 – –56C 31⁄2 101⁄2 12 13⁄8 1 3 69⁄16 47⁄8 1 –
184TC 41⁄2 101⁄2 12 13⁄8 1 51⁄2 85⁄8 71⁄2 – –56C 31⁄2 91⁄8 101⁄2 15⁄8 11⁄16 3 69⁄16 47⁄8 – –
184TC 41⁄2 91⁄8 101⁄2 15⁄8 11⁄16 51⁄2 85⁄8 71⁄2 – –56C 31⁄2 91⁄8 101⁄2 2 11⁄16 3 69⁄16 47⁄8 23⁄4 –
184TC 41⁄2 91⁄8 101⁄2 2 11⁄16 51⁄2 85⁄8 71⁄2 13⁄4 –3SVB/3SVD 213TC 51⁄4 91⁄8 101⁄2 2 27⁄16 51⁄2 91⁄2 81⁄2 1 –
215TC 51⁄4 91⁄8 101⁄2 2 27⁄16 7 91⁄2 81⁄2 1 –254TC 61⁄4 91⁄8 101⁄2 2 215⁄16 81⁄4 111⁄4 10 – –
184TCH 41⁄2 117⁄8 131⁄4 2 11⁄16 51⁄2 85⁄8 71⁄2 13⁄4 –213TC 51⁄4 117⁄8 131⁄4 2 27⁄16 51⁄2 91⁄2 81⁄2 1 –215TC 51⁄4 117⁄8 131⁄4 2 27⁄16 7 91⁄2 81⁄2 1 –254TC 61⁄4 117⁄8 131⁄4 2 215⁄16 81⁄4 111⁄4 10 – –
184TCH 41⁄2 91⁄8 101⁄2 2 11⁄16 51⁄2 85⁄8 71⁄2 13⁄4 –213TC 51⁄4 91⁄8 101⁄2 2 27⁄16 51⁄2 91⁄2 81⁄2 1 –
4SVB/4SVD 215TC 51⁄4 91⁄8 101⁄2 2 27⁄16 7 91⁄2 81⁄2 1 –254TC 61⁄4 91⁄8 101⁄2 2 215⁄16 81⁄4 111⁄4 10 – –256TC 61⁄4 91⁄8 101⁄2 2 215⁄16 10 111⁄4 10 – –
184TCH 41⁄2 117⁄8 131⁄4 2 17⁄16 51⁄2 85⁄8 71⁄2 13⁄4 –213TC 51⁄4 117⁄8 131⁄4 2 27⁄16 51⁄2 91⁄2 81⁄2 1 –
4SVC 215TC 51⁄4 117⁄8 131⁄4 2 27⁄16 7 91⁄2 81⁄2 1 –254TC 61⁄4 117⁄8 131⁄4 2 215⁄16 81⁄4 111⁄4 10 – –256TC 61⁄4 117⁄8 131⁄4 2 215⁄16 10 111⁄4 10 – –
Motor PumpSeries A B C D E F G H Shim Shim
Thickness Thickness213TC 51⁄4 117⁄8 131⁄4 2 27⁄16 51⁄2 91⁄2 81⁄2 13⁄4 –215TC 51⁄4 117⁄8 131⁄4 2 27⁄16 7 91⁄2 81⁄2 13⁄4 –254TC 61⁄4 117⁄8 131⁄4 2 215⁄16 81⁄4 111⁄4 10 3⁄4 –256TC 61⁄4 117⁄8 131⁄4 2 215⁄16 10 111⁄4 10 3⁄4 –284TC 7 117⁄8 131⁄4 2 215⁄16 91⁄2 121⁄4 11 – –286TC 7 117⁄8 131⁄4 2 215⁄16 11 121⁄4 11 – –213TC 51⁄4 117⁄8 131⁄4 29⁄16 27⁄16 51⁄2 91⁄2 81⁄2 13⁄4 –215TC 51⁄4 117⁄8 131⁄4 29⁄16 27⁄16 7 91⁄2 81⁄2 13⁄4 –254TC 61⁄4 117⁄8 131⁄4 29⁄16 215⁄16 81⁄4 111⁄4 10 3⁄4 –256TC 61⁄4 117⁄8 131⁄4 29⁄16 215⁄16 10 111⁄4 10 3⁄4 –284TC 7 117⁄8 131⁄4 29⁄16 215⁄16 91⁄2 121⁄4 11 – –286TC 7 117⁄8 131⁄4 29⁄16 215⁄16 11 121⁄4 11 – –
FE+L2
D
CB
A
FE+L2
D
2 – 5⁄8" HOLES
2 – 5⁄8" HOLES
GH
CB
A
GH
4 holes per chart
Flanges can be rotated 90° left or right.
4 holes per chart
Drain plug
Fill/vent plug
Discharge
Suction
MotorFrame
MotorFrame
For all other dimensions see dimensions and weights table.All dimensions are in inches.
6SVB/6SVD
5SVB/5SVD
© 1997 Goulds PumpsPrinted in USAGLSSV
Frame Hole Diameter56 11⁄32
140 11⁄32
180 13⁄32
210 13⁄32
250 17⁄32
280 17⁄32
NOTEDimensions H and G are motorfoot dimensions.Dimensions B and C are pumpfoot dimensions.
NOTE: L2 dimensions located on vertical version drawings.
Not availableless motor.
Goulds Pumps240 Fall StreetSeneca Falls, NY 13148
top related