stainless steel catalogue - regal beloit · aa 213/5tc (ø8.88”) d nema input flanges c food lube...
Post on 20-Sep-2020
3 Views
Preview:
TRANSCRIPT
MARATHON GEARBOXESSTAINLESS STEEL CATALOGUE
2
3
See technical data table.
Page 9
Full stainless steel gearboxes with one stageof reduction.
See technical data table.
Page 8
See technical data table.
Full stainless steel Worm gearboxes.
IN THIS CATALOGUE
Full Stainless steel - One step gearboxes
Full Stainless steel - Worm gearboxes
4 Stainless Steel GearboxesSquare Worm
I30, 21 Nm 8
I45, 41 Nm 10
I50, 72 Nm 12
I63, 147 Nm 14
I85, 347 Nm 16
I11, 651 Nm 18
21 Stainless Steel GearboxesSingle Stage
411I, 38 Nm 24
4
Stainless steel hollow shaft.
Output seals (FPM-fkm)With external dust protection lips.
Full stainless steel housingSpecial housing designed to keep adequate lubrication with low oil quantity to avoidinternal pressures.
Orings on allclosing covers.
100% factory pressure leak test.
Second bearingStandard second bearingon motor flange side andtwo oil seals with vertical motor position.
STANDARD FEATURES
OptionsProtective seals cup to stand high pressurecleaning for hollowor extended shaft version.
Output shaftInterchangeableright or left hand outputshafts available.
vent free
oil freeVent free designNo breather or vents to leak! Factory lubricated for life with synthetic, semi-fluid gear lubricant with an operating range of -15ºC to 130ºC.
FlangeFully modular toIEC B14 and compactintegrated motor.NEMA C flange.
Stainless Steel Worm Gearboxes
ø
AA213/5TC(ø8.88”)
D Nema Input Flanges
C Food Lube
Size
P UNI45
I30I45I50I63I85I11
Ratio
S
ø0.750”ø1.000”ø1.125”ø1.500”ø2.000”
INCH
I45I50I63I85I11
10HubType Mounting
See technical data table
Motor Size
IEC
-O56B14(ø80)
-QOutput Shaft
BR
FL
Z
S
UN
ø14ø18ø25ø25ø35ø42
STANDARD
I30I45I50I63I85I11
P
M
ø
-MWithout flange
I
I
I30 -P63B14(ø90)
-W56C
(ø6.5”)
I45 -P63B14(ø90)
-W56C
(ø6.5”)
-Q71B14(ø105)
-R80B14(ø120)
I50 -P63B14(ø90)
I63
-D80B5
(ø200)
I85 -E90B5
(ø200)
-U100-112B14
(ø160)
-Q71B14(ø105)
-R80B14(ø120)
-Q71B14(ø105)
-T90B14(ø140)
-W56C
(ø6.5”)
-X143/5TC(ø6.5”)
-W56C
(ø6.5”)
-W56C
(ø6.5”)
-X143/5TC(ø6.5”)
-Y182/4TC(ø8.88”)
Full stainlesssteel
torque arm
A
B Protective Seals CupOPEN TYPE
On requestProtective Seals CupCLOSE TYPE
B
-D80B5
(ø200)
I11 -E90B5
(ø200)
-U100-112B14
(ø160)-X
143/5TC(ø6.5”)
On request we can deliver our products according to the ATEX.
-Y182/4TC(ø8.88”)
SPECIAL SERIES
Xø19ø24
I45I50
-0Type R
R
HOW TO ORDER
1
5
ø
AA213/5TC(ø8.88”)
D Nema Input Flanges
C Food Lube
Size
P UNI45
I30I45I50I63I85I11
Ratio
S
ø0.750”ø1.000”ø1.125”ø1.500”ø2.000”
INCH
I45I50I63I85I11
10HubType Mounting
See technical data table
Motor Size
IEC
-O56B14(ø80)
-QOutput Shaft
BR
FL
Z
S
UN
ø14ø18ø25ø25ø35ø42
STANDARD
I30I45I50I63I85I11
P
M
ø
-MWithout flange
I
I
I30 -P63B14(ø90)
-W56C
(ø6.5”)
I45 -P63B14(ø90)
-W56C
(ø6.5”)
-Q71B14(ø105)
-R80B14(ø120)
I50 -P63B14(ø90)
I63
-D80B5
(ø200)
I85 -E90B5
(ø200)
-U100-112B14
(ø160)
-Q71B14(ø105)
-R80B14(ø120)
-Q71B14(ø105)
-T90B14(ø140)
-W56C
(ø6.5”)
-X143/5TC(ø6.5”)
-W56C
(ø6.5”)
-W56C
(ø6.5”)
-X143/5TC(ø6.5”)
-Y182/4TC(ø8.88”)
Full stainlesssteel
torque arm
A
B Protective Seals CupOPEN TYPE
On requestProtective Seals CupCLOSE TYPE
B
-D80B5
(ø200)
I11 -E90B5
(ø200)
-U100-112B14
(ø160)-X
143/5TC(ø6.5”)
On request we can deliver our products according to the ATEX.
-Y182/4TC(ø8.88”)
SPECIAL SERIES
Xø19ø24
I45I50
-0Type R
R
HOW TO ORDER
1
6
9550P [KW] =M [Nm] n [rpm]
d [mm]fK
M [Nm] 2000
1000P [KW] =M [Kg] g [9.81] v [m / s]
1000P [KW] =F [N] v [m / s]
FR [N] =
M
d
n [rpm]M [lb in] =63030 P[HP]
n [rpm]M [Nm] =9550 P[KW]
d [in]fK
M [lb in] 8.9FR [N] =
Rotation
Linear Movement
Lifting
— If your application requires higher radial loads, contact your local Regal office.
REQUIRED POWER
Output torque
Diameter of driving element
1.15 Gear Wheels1.25 Chain Sprochets1.75 Narrow V-belt Pulley2.50 Flat-Belt Pulley
- Radial load generated by external transmissions keyed onto input and/or output shafts.
TORQUE
fK
FR
FR
USEFUL FORMULAS
RADIAL LOADS
Factor
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
Ratio
Transmitted Torque Service Factor
NotesNominal Module
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code Input SpeedDynamic Efficiency
41NmStainless Steel - Gear
B
A
C
D
B)
C)
B)
Type of load and starts per hour Operating hours per day
<2 h 2 - 8 h 8 - 16 h
≤ 10
Uniform 0.9 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform
Moderate 1.75 2
Heavy 2 2.25
1.5
1.75
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
1.25 1.5
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
1.75
200140100
71014
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
807977
2.22.22.4
010203
RD Ratioscode
Input Speed (n1) = 1400 min-1
DynamicEfficiency
ToothModule
-
-
B5 Motor Flangesnot available
-
-
-Q
71
AvailableB14 Motor Flanges
-P
63
B-CB-CB-C
P1R M2R
0.370.370.37
142027
2.21.51.1
[mm]
0.800.570.41
303030
I45 Rating - Stainless Steel WORM GEARBOXES
HOW TO SELECT A GEARBOX
7
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
Ratio
Transmitted Torque Service Factor
NotesNominal Module
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code Input SpeedDynamic Efficiency
41NmStainless Steel - Gear
B
A
C
D
B)
C)
B)
Type of load and starts per hour Operating hours per day
<2 h 2 - 8 h 8 - 16 h
≤ 10
Uniform 0.9 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform
Moderate 1.75 2
Heavy 2 2.25
1.5
1.75
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
1.25 1.5
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
1.75
200140100
71014
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
807977
2.22.22.4
010203
RD Ratioscode
Input Speed (n1) = 1400 min-1
DynamicEfficiency
ToothModule
-
-
B5 Motor Flangesnot available
-
-
-Q
71
AvailableB14 Motor Flanges
-P
63
B-CB-CB-C
P1R M2R
0.370.370.37
142027
2.21.51.1
[mm]
0.800.570.41
303030
I45 Rating - Stainless Steel WORM GEARBOXES
HOW TO SELECT A GEARBOX
8
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
RADIAL AND AXIAL LOADSOutput Shaft
RADIAL AND AXIAL LOADS
21NmStainless Steel - Gear
Motor Flange Holes PositionAvailable on Request without Reduction Bushing C)Motor Flanges Available Supplied with Reduction Bushing B)B)
2802001409370473523
17.5
5710152030406180
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
RD
DynamicEfficiency
828078737062575048
1.261.441.441.441.091.441.090.720.56
Ratioscode
010203040506070809
ToothModule
Input Speed (n1) = 1400 min-1
-
-
-
-
FR[N]
FA[N]
n[min ]
2-1
120700800900
100012501400
600140160180200250280
20015010075502515
FA
FR
B5 Motor Flangesnot available
AvailableB14 Motor Flanges
-P
63
-O
56
B-CB-CB-CB-CB-CB-CB-CB-CB-C
LUBRICATION I30 Oil Quantity 0.06 Lt.
P1R M2R
0.180.180.180.180.180.120.120.090.09
5710131715191916
3.32.41.81.41.11.41.11.11.0
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
0.600.440.320.250.200.170.130.100.06
171717191921202016
Unit I30 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( )
FR
FA
100
FR[N]
FA[N]20
n[min ]1400
1-1
tab. 2
[mm]
I30 Rating - Stainless Steel WORM GEARBOXES
9
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
RADIAL AND AXIAL LOADSOutput Shaft
RADIAL AND AXIAL LOADS
21NmStainless Steel - Gear
Motor Flange Holes PositionAvailable on Request without Reduction Bushing C)Motor Flanges Available Supplied with Reduction Bushing B)B)
2802001409370473523
17.5
57
10152030406180
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
RD
DynamicEfficiency
828078737062575048
1.261.441.441.441.091.441.090.720.56
Ratioscode
010203040506070809
ToothModule
Input Speed (n1) = 1400 min-1
-
-
-
-
FR[N]
FA[N]
n[min ]
2-1
120700800900100012501400
600140160180200250280
20015010075502515
FA
FR
B5 Motor Flangesnot available
AvailableB14 Motor Flanges
-P
63
-O
56
B-CB-CB-CB-CB-CB-CB-CB-CB-C
LUBRICATION I30 Oil Quantity 0.06 Lt.
P1R M2R
0.180.180.180.180.180.120.120.090.09
57
10131715191916
3.32.41.81.41.11.41.11.11.0
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
0.600.440.320.250.200.170.130.100.06
171717191921202016
Unit I30 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( )
FR
FA
100
FR[N]
FA[N]20
n[min ]1400
1-1
tab. 2
[mm]
I30 Rating - Stainless Steel WORM GEARBOXES 21NmStainless Steel - Gear
BI30UN... Modular Base
PI30UN...
97
M.Flanges Kit Code A56B14 KI304046 80 61.5
Basic Wormbox
4 holes M6x7
Mounting HolesPosition
(A)
Side ( A ) Mounting Holes
19
6
66
37
97
8.5
58
8710
ø60
85.5
39
ø110
50M6x10
GearboxWeight 2.5 kg
øF
øF
A
64
4030
57
55
55
Output Flange
M8x11
Kit Code KI459011
39
PI30FL...
90KI30404563B14 62.5
(A)
5
14H8
16.3
Standard
38
+0.0
5+0
.15
4
11
13.1
For all ratio1/5÷1/80
+0.04+0.06
Input Bore
93
56
30
29
48
20
Single Shaft
Kit Code KI0305028
Kit Code KI450209Protection Cup(on request)
-0.020-0.005
80
20
11
17
63
RI30UN... Input Shaft PI30.....S...
5
1415.8
Kit Code KI309027LM
35.5
110
55
10.5
20
25
2.5
18
583
10.2
ø9 h6
PI30BR... Reaction Arm
I30
10
41NmStainless Steel - Gear
RADIAL AND AXIAL LOADSOutput Shaft
RADIAL AND AXIAL LOADS
FA
FR
C)B)B)
200140100675038302320
13.7
71014212837466070102
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
80797767656359565449
2.22.22.41.62.51.81.51.21.0
0.72
01020304050607080910
RD Ratioscode
Input Speed (n1) = 1400 min-1
DynamicEfficiency
ToothModule
-
-
B5 Motor Flangesnot available
-
-
Motor Flange Holes PositionAvailable on Request without Reduction BushingSupplied with Reduction BushingMotor Flanges Available
FR[N]
FA[N]
n[min ]
2-1
180100011001200140018002000
900200220240260300400
20015010075502515
-Q
71
AvailableB14 Motor Flanges
-P
63
B-CB-CB-CB-CB-CB-CB-CB-CB-CB-C
P1R M2R
0.370.370.370.370.250.250.250.180.120.12
14202736314046413141
2.21.51.11.21.31.00.91.01.00.7
Unit I45 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
EN
[mm]
On request
0.15 LT 0.15 LT 0.20 LT 0.15 LT 0.15 LT 0.15 LTB3 B6 B7 B8 V5 V6
Standard
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
210
FR[N]
FA[N]42
n[min ]1400
1-1
tab. 2
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( )
FR
FA
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
0.800.570.410.430.330.260.220.180.120.09
30303041414141413029
I45 Rating - Stainless Steel WORM GEARBOXES
11
41NmStainless Steel - Gear
RADIAL AND AXIAL LOADSOutput Shaft
RADIAL AND AXIAL LOADS
FA
FR
C)B)B)
200140100675038302320
13.7
71014212837466070
102
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
80797767656359565449
2.22.22.41.62.51.81.51.21.0
0.72
01020304050607080910
RD Ratioscode
Input Speed (n1) = 1400 min-1
DynamicEfficiency
ToothModule
-
-
B5 Motor Flangesnot available
-
-
Motor Flange Holes PositionAvailable on Request without Reduction BushingSupplied with Reduction BushingMotor Flanges Available
FR[N]
FA[N]
n[min ]
2-1
180100011001200140018002000
900200220240260300400
20015010075502515
-Q
71
AvailableB14 Motor Flanges
-P
63
B-CB-CB-CB-CB-CB-CB-CB-CB-CB-C
P1R M2R
0.370.370.370.370.250.250.250.180.120.12
14202736314046413141
2.21.51.11.21.31.00.91.01.00.7
Unit I45 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
EN
[mm]
On request
0.15 LT 0.15 LT 0.20 LT 0.15 LT 0.15 LT 0.15 LTB3 B6 B7 B8 V5 V6
Standard
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
210
FR[N]
FA[N]42
n[min ]1400
1-1
tab. 2
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( )
FR
FA
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
0.800.570.410.430.330.260.220.180.120.09
30303041414141413029
I45 Rating - Stainless Steel WORM GEARBOXES
Kit Code KI450209Protection Cup(on request)Kit Code KI459027LM
Kit Code KI0455028
-0.020-0.005
100
20
11
55
23
1175.5
6
1820.5
40.5
30
32
1.3
130
22
Single ShaftRI45UN... Input Shaft PI45.....S...PI45BR... Reaction Arm
30684
12.5
ø11 h6
43
41NmStainless Steel - Gear
Standard
BI45UN... Modular Base
PI45UN...
127
Basic Wormbox
4 holes M6x11
Mounting HolesPosition
(A)
Side ( A ) Mounting Holes
21
6
86
43
42
8.5
58
8710
ø60
90.5
ø110
5.0 kg
øF
A
64
554572
116.5
65
Output Flange
M8x11
Kit Code KI459011
55
PI45FL...
(A)
+0.0
5+0
.15
6
19H8
21.8
On Request
127
5559
M6x105
14
16.4
For all ratio1/7÷1/102
+0.04+0.07
Input Bore66
45M.Flanges Kit Code A
63B14 KI504047 90 73.5øF
656
18H8
20.8
105KI50404571B14 71
55.5
GearboxWeight
I45
12
72NmStainless Steel - Gear
RADIAL AND AXIAL LOADSOutput Shaft
RADIAL AND AXIAL LOADS
FA
FR
FR[N]
FA[N]
n[min ]
2-1
240140015001700190025002800
1200280300340380480560
20015010075502515
Motor Flange Holes PositionAvailable on Request without reduction bushing C)Motor Flanges Available Supplied with Reduction Bushing B)B)
20014010078544739332321
17.514
710141826303643606880100
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
RD
DynamicEfficiency
828079756970696658575450
2.52.42.62.02.72.52.11.81.31.21.00.8
Ratioscode
010203040512060708091011
ToothModule
Input Speed (n1) = 1400 min-1
-
-
B5 Motor Flangesnot available
-
-
-P
63
B-CB-CB-CB-CB-CB-CB-CB-CB-CB-CB-CB-C
-Q
71
BBBBBB
-R
80
AvailableB14 Motor Flanges
P1R M2R
0.750.750.750.550.550.550.370.370.250.250.180.12
294157516779637259665341
1.91.51.21.21.00.91.21.01.00.91.11.3
Unit I50 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
EN
[mm]
On request
0.22 LT 0.22 LT 0.28 LT 0.22 LT 0.22 LT 0.22 LTB3 B6 B7 B8 V5 V6
Standard
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( )
FR
FA
380
FR[N]
FA[N]76
n[min ]1400
1-1
tab. 2
1.51.10.900.670.540.500.430.350.260.220.190.15
576268626672726862585751
I50 Rating - Stainless Steel WORM GEARBOXES
13
72NmStainless Steel - Gear
RADIAL AND AXIAL LOADSOutput Shaft
RADIAL AND AXIAL LOADS
FA
FR
FR[N]
FA[N]
n[min ]
2-1
240140015001700190025002800
1200280300340380480560
20015010075502515
Motor Flange Holes PositionAvailable on Request without reduction bushing C)Motor Flanges Available Supplied with Reduction Bushing B)B)
20014010078544739332321
17.514
710141826303643606880
100
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
QUICK SELECTION
RD
DynamicEfficiency
828079756970696658575450
2.52.42.62.02.72.52.11.81.31.21.00.8
Ratioscode
010203040512060708091011
ToothModule
Input Speed (n1) = 1400 min-1
-
-
B5 Motor Flangesnot available
-
-
-P
63
B-CB-CB-CB-CB-CB-CB-CB-CB-CB-CB-CB-C
-Q
71
BBBBBB
-R
80
AvailableB14 Motor Flanges
P1R M2R
0.750.750.750.550.550.550.370.370.250.250.180.12
294157516779637259665341
1.91.51.21.21.00.91.21.01.00.91.11.3
Unit I50 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
EN
[mm]
On request
0.22 LT 0.22 LT 0.28 LT 0.22 LT 0.22 LT 0.22 LTB3 B6 B7 B8 V5 V6
Standard
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( )
FR
FA
380
FR[N]
FA[N]76
n[min ]1400
1-1
tab. 2
1.51.1
0.900.670.540.500.430.350.260.220.190.15
576268626672726862585751
I50 Rating - Stainless Steel WORM GEARBOXES 72NmStainless Steel - Gear
BI50UN... Modular Base
PI50UN...
141
Basic Wormbox
Mounting HolesPosition
(A)
Side ( A ) Mounting Holes
30
6
102
46
60
10.5
58
9010
ø70
98.5
ø123
7.3 kg
øF
A
75
6050
81
134
81
Output Flange
M8x11
Kit Code KI509011
68
PI50FL...
(A)
+0.1
5+0
.20
M6X9 - 60°6 holes
M.Flanges Kit Code AøF
120KI50404680B14 76105KI50404571B14 78
Standard
8
24H8
27.3
On Request
818
25H8
28.3
141
6859
M6x10
6
19
21.8
From 1/7 to 1/30
+0.04+0.07
Input Bore
72.3
50
5
14
16.4
+0.04+0.07
From 1/36 to 1/100
63B14 KI504047 90 78
56
60
GearboxWeight
Kit Code KI500209Protection Cup(on request)Kit Code KI509027LM
Kit Code KI0505028
-0.020-0.005
110
20
11
67
31
7.5100
8
2528
49
40
52
6
140
30
Single ShaftRI50UN... Input Shaft PI50.....S...PI50BR... Reaction Arm
3074.55
18
ø16 h6
I50
14
RADIAL AND AXIAL LOADSOutput Shaft
RADIAL AND AXIAL LOADS
FRFAn2
360200023002500300038004000
1800400460500600700800
20015010075502515
FA
FR
AvailableB14 Motor Flanges
RD Ratioscode
-Q -R
71 80
DynamicEfficiency
-T
90
B-CB-CB-CB-CB-CB-CB-CB-CB-CB-CB-CB-C
B-CB-CB-CB-CB-CB-CB-CCCCCC
838179787574686662605752
3.13.13.12.62.03.22.72.11.61.51.31.1
010203040506070812091011
ToothModule
Input Speed (n1) = 1400 min-1
Motor Flange Holes PositionAvailable on Request without Reduction Bushing C)
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
2001409374584739312321
17.514.9
71015192430364560678094
QUICK SELECTION
Motor Flanges Available Supplied with Reduction Bushing B)B)
147NmStainless Steel - Gear
-
-
B5 Motor Flangesnot available
-
-
On request
0.60 LT 0.60 LT 0.82 LT 0.60 LT 0.60 LT 0.60 LTB3 B6 B7 B8 V5 V6
Standard
P1R M2R
1.81.81.51.11.11.10.750.550.550.550.370.37
7199121111135167125111140151115123
1.81.41.11.21.00.91.21.20.90.81.01.0
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
Unit I63 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
EN
[mm]
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( ) 450
FR[N]
FA[N]90
n[min ]1400
1-1
FR
FA
tab. 2
3.22.41.71.41.20.960.880.670.510.450.380.36
125134138138142146147135130124119119
I63 Rating - Stainless Steel WORM GEARBOXES
1
15
147Nm Stainless Steel - Gear
BI63UN... Modular Base
PI63UN...
175
M.Flanges Kit Code A71B14 KI634047 105 97
Basic Wormbox
4 holes M8x11
Mounting HolesPosition
(A)
Side ( A ) Mounting Holes
46
6
128
64
92
10.5
56
15012
ø115
116
ø175
14.6 kg
øF
øF
A
92
756310
0
162
120
Output Flange
M10x17
Kit Code KI639011
77
PI63FL...
120140
KI634046KI634041
80B1490B14
9899
(A)
+0.1
5+0
.20
Standard
8
28H8
31.3
On Request
1208
25H8
28.3
80
8
24
27.3
From 1/7 to 1/36
+0.04+0.07
Input Bore
6
19
21.8
+0.05+0.07
From 1/45 to 1/94
175
77 M8x1479
63
GearboxWeight
64
91
Kit Code KI630209Protection Cup (on request)
Kit Code KI639027LM
Kit Code KI0635028Kit Code KI0705028 on request
130
20
11
76
50.5
e1n1
b1
d1t2
72.5
50
60
4
160
49.5
Single ShaftRI63UN... Input Shaft PI63.....S...PI63BR... Reaction Arm
45936
20.5
ø18 h6
M8x20
e1b1 n13.2
3.5
8
8
121.9
122.2
d1
28
t228
31-0.005-0.020
25-0.005-0.020Standard
Onrequest
I63
16
BBBBBB
347NmStainless Steel - Gear
RADIAL AND AXIAL LOADSOutput Shaft FR
[N]FA[N]
n[min ]-1
FA
FR
500290030003500400050005800
2500580600700800
10001160
20015010075502515
RD Ratioscode
DynamicEfficiency
888078797875716866655853
4.234.24.53.43.14.73.53.12.72.11.91.5
010203040506070809101112
ToothModule
Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
20014010070645037302721
18.914.6
71014202228384652677496
QUICK SELECTION
-U
100-112
AvailableB14 Motor Flanges
-E
90
AvailableB5 Motor Flanges
-D
80
BBBBBBBBBBBB
RADIAL AND AXIAL LOADS2
On request
1.40 LT 1.40 LT 1.70LT 1.40 LT 1.40 LT 1.40 LTB3 B6 B7 B8 V5 V6
Standard
P1R M2R
4.04.03.02.22.22.21.51.51.11.10.750.55
168218223237258315276320258327220191
1.51.31.41.21.11.11.21.01.10.91.21.3
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
Unit I85 is supplied with synthetic oil, providing “long life” lubrication.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
EN
[mm]
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
Motor Flange Holes PositionAvailable on Request without Reduction Bushing C)Motor Flanges Available Supplied with Reduction Bushing B)B)
n[min ]
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( ) 809
FR[N]
FA[N]1601400
1-1
FR
FA
tab. 2
6.15.24.12.72.52.41.81.51.20.970.910.70
257284305294294347336326289289268242
Rating - Stainless Steel WORM GEARBOXESI85 347NmStainless Steel - Gear
BI85UN... Modular Base
PI85UN...
232
M. Flanges Kit Code A
100-112B14 KI854041 160 116
Basic Wormbox
M8 x 11 - 60°
Mounting HolesPosition
(A)
Side ( A ) Mounting Holes
53
6
164
82
106
13
81
17613
ø152
148.5
ø205
23.3 kg
øFøF
A
120
94.5
85137.
5
202
135
Output Flange
M12x19
Kit Code KI859011
103
PI85FL...
(A)
0+0.0
6
6 holes 135
Standard
10
35H8
38.3
8
28
31.3
From 1/7 to 1/28
+0.04+0.07
Input Bore
8
24
27.4
+0.04+0.07
From 1/38 to 1/96
232
103105
M8x14
110
85
80-90B5 KI854042 200 118
82
98
GearboxWeight
52°
Kit Code KI850209Protection Cup(on request)Kit Code KI859027LM
Kit Code KI0855028
-0.020-0.005
160
26
21
96
55
13.5140.5
10
3538
77.5
50
60
5
195
54
Single ShaftRI85UN... Input Shaft PI85.....S...PI85BR... Reaction Arm
501128
28
ø25 h6
I85
17
347NmStainless Steel - Gear
BI85UN... Modular Base
PI85UN...
232
M. Flanges Kit Code A
100-112B14 KI854041 160 116
Basic Wormbox
M8 x 11 - 60°
Mounting HolesPosition
(A)
Side ( A ) Mounting Holes
53
6
164
82
106
13
81
17613
ø152
148.5
ø205
23.3 kg
øFøF
A
120
94.5
85137.
5
202
135
Output Flange
M12x19
Kit Code KI859011
103
PI85FL...
(A)
0+0.0
6
6 holes 135
Standard
10
35H8
38.3
8
28
31.3
From 1/7 to 1/28
+0.04+0.07
Input Bore
8
24
27.4
+0.04+0.07
From 1/38 to 1/96
232
103105
M8x14
110
8580-90B5 KI854042 200 118
82
98
GearboxWeight
52°
Kit Code KI850209Protection Cup(on request)Kit Code KI859027LM
Kit Code KI0855028
-0.020-0.005
160
26
21
96
55
13.5140.5
10
3538
77.5
50
60
5
195
54
Single ShaftRI85UN... Input Shaft PI85.....S...PI85BR... Reaction Arm
501128
28
ø25 h6
I85
18
651NmStainless Steel - Gear
On request
3.50 LT 2.50 LT 2.50 LT 2.10 LT 1.60 LT 1.60 LTB3 B6 B7 B8 V5 V6
Standard
tab. 1For all details on lubrication and plugs please consult with a Regaloffice or representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
BBBBBBBBB
RD Ratioscode
DynamicEfficiency
888682828076757370696560
5.55.45.34.53.95.64.74.03.52.92.21.9
010203040506070809101112
ToothModule
Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
2001408870614737312622
16.714.1
71016202330384553648499
QUICK SELECTION
-U
100-112
AvailableB14 Motor Flanges
-E
90
AvailableB5 Motor Flanges
-D
80
BBBBBBBBBBBB
P1R M2R
4.04.04.04.03.03.03.02.22.21.51.11.1
168235358447377467583493557452410446
2.92.21.51.21.41.41.11.21.11.21.21.1
RADIAL AND AXIAL LOADSOutput Shaft FR
[N]FA[N]
n[min ]-1
FA
FR
600330036004000460060007000
2900700750800920
12001400
20015010075502515
RADIAL AND AXIAL LOADS2
Unit I11 is supplied with synthetic oil, providing “long life” lubrication. For mounting position V5-V6please contact us.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
EN
[mm]
* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
Motor Flange Holes PositionAvailable on Request without Reduction Bushing C)Motor Flanges Available Supplied with Reduction Bushing B)B)
n[min ]
*Strong axial loads in the DX direction are not allowed.
Input Shaft
*SX DX ( ) 1140
FR[N]
FA[N]2281400
1-1
FR
FA
tab. 2
11.59.06.04.94.14.23.32.72.51.81.31.2
483525536546515651641599620536494483
Rating - Stainless Steel WORM GEARBOXESI11
1
19
52°
(A)
651 NmStainless Steel - Gear
BI11UN... Modular Base
PI11UN...
280
M.Flanges Kit Code A
100-112B14 KI854041 160 135.5
Basic Wormbox
M12 x 19 - 60°
Mounting HolesPosition
(A)
Side ( A ) Mounting Holes
52.5200
100
105
38.5 kg
øFøF
A
140
117.
511
016
2.5
242
140
M14x21
117.5
6 holes 140
Standard
12
42H8
45.3
8
28
31.3
From 1/7 to 1/53
+0.04+0.07
Input Bore
8
24
27.4
+0.04+0.07
From 1/64 to 1/99
280
117.5105
M8x14
129.5
110
80-90B5 KI854042 200 137.5
100
117.5
GearboxWeight
Kit Code KI119027LM
185
26
21
57.5
220
56.5
PI11BR... Reaction Arm
RI11UN... Input Shaft
50131.58
28
ø25 h6
I111
20
21
FlangeFully modular toIEC B14 and compactintegrated motor.NEMA C flange.
Stainless steeloutput shaftWith wellproportionedbearings.
Smooth stainless steel housing
Lubricated for life with
synthetic oil with operative rangefrom -15° to +130°C
GearsHardened and ground gears.
Standard FPM (fkm) seals
A MODULAR AND COMPACT PRODUCT
Stainless Steel One Step Gearboxes
Ideal for use asfirst step withworm gearboxes.
22
- B3 is supplied with standard oil quantity
- Please specify in the order if you required other mounting positions
Size
P -F411I
411I
Ratio
41.57
Output ShaftType Mounting
See technical data table
Motor Size
IEC
Output Flange
P
M
C
ø19
STANDARD STANDARD
V5
411I
C
Mounting Position
B3
V8
B8
B6
B7
V6
411I
-R90B14
(ø140)
71B14(ø105)
80B14(ø120)
-T
-Q
-Q
ø200
B
411I
4
411I
-2 ø19(80B5)
ø24(90B5)
ø14(71B5)
-3
-1
B Food Lube
On request
B3-N
On request we can deliver our products according to the ATEX.
-F
ø
N Without flange
Without flange
HOW TO ORDER
23
9550P [KW] =M [Nm] n [rpm]
1000P [KW] =M [Kg] g [9.81] v [m / s]
1000P [KW] =F [N] v [m / s]
FR
M
d [mm]fK
M [Nm] 2000FR [N] =
n [rpm]M [lb in] =63030 P[HP]
n [rpm]M [Nm] =9550 P[KW]
d [in]fK
M [lb in] 8.9FR [N] =
d
Rotation
Linear movement
Lifting
— If your application requires higher radial loads, contact our technical office. Higher load may be possible.
REQUIRED POWER
Output torque
Diameter of driving element
1.15 Gear Wheels1.25 Chain Sprochets1.75 Narrow V-belt Pulley2.50 Flat-Belt Pulley
- Radial load generated by external transmissions keyed onto input and/or output shafts.
TORQUE
fK
USEFUL FORMULAS
RADIAL LOADS
Factor
24
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
38NmOne Step
B
A
C
D
B)
C)
B)
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
892493426362
1.572.843.293.87
1.51.51.51.5
1.31.21.21.0
Ratioscode
ø
Standardø19
2844195417561558
Output Shaft
01020304
15.728.432.938.7
QUICK SELECTION Input Speed (n1) = 1400 min-1
- - - -
- - - -
B5 Motor Flangesnot available
-Q -R
71 80
-T
90
CCCC
CCCC
AvailableB14 Motor Flanges
Type of load and starts per hourOperating hours per day
3 h 10 h 24 h
≤ 10
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75 2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
P1R M2R
1.901.841.731.54
20353840
411I Rating - Stainless Steel ONE STEP GEARBOXES
HOW TO SELECT A GEARBOX
25
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
38NmOne Step
B
A
C
D
B)
C)
B)
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
892493426362
1.572.843.293.87
1.51.51.51.5
1.31.21.21.0
Ratioscode
ø
Standardø19
2844195417561558
Output Shaft
01020304
15.728.432.938.7
QUICK SELECTION Input Speed (n1) = 1400 min-1
- - - -
- - - -
B5 Motor Flangesnot available
-Q -R
71 80
-T
90
CCCC
CCCC
AvailableB14 Motor Flanges
Type of load and starts per hourOperating hours per day
3 h 10 h 24 h
≤ 10
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75 2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
P1R M2R
1.901.841.731.54
20353840
411I Rating - Stainless Steel ONE STEP GEARBOXES
HOW TO SELECT A GEARBOX
g6
P411I-N... Basic Gearbox
h1
ø200
k1
Kit Code KI4119010
p1 h1 x
38NmOne Step
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
891493425362303222170129
1.572.843.293.874.626.308.2210.86
1.51.51.51.51.51.10.550.37
1.31.21.21.01.01.01.31.0
Ratioscode
ø
Standardø19
284419541756155813601063974776
Output Shaft
0102030405060708
1628333946463027
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without Reduction BushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
- - - -
- - - -
B5 Motor Flangesnot available
Q R
71 80
T
90
CCCCCCCC
CCCCCCCC
AvailableB14 Motor Flanges
GearboxWeight 5.5 kg
EN Unit 411I is supplied with synthetic oil for lifetime lubrication, no maintenance is necessary.
Output Shaft
X
FA (N)
FR (N) Feq (N)
910FRFA
1827001000200600
11502304001250250300
14502902001600320140
Feq = FR . 48.5X+28.5
FRFAn2 FRFAn2
= =
n2
P411I-F... Output Flange
n°4 - ø11.5
3.5
Detail Y
40
Detail Y n°4 - M8x15p1
M6x16ø19 h6
Input Flanges
Output Shafts
ø 19x40Shaft - d1
6 M6x1621.5Standard
P1R M2R
1.91.81.71.51.51.10.690.39
2035384047463828
ø90
5
g6
103.530
40
38
2.5
x
k1
ø130
f7
ø165
7ø19 h6
ø72
H6
d1
M6x16
47 80
129.5 KI63404680 B14130.5 KI63404190 B14
128.5Kit Code
71 B14g6k1
KI634047120140
105
LUBRICATION 411I Oil Quantity 0.14 Lt.
For all details on lubrication and plugs please consult with a Regal officeor representative.
AGIP Telium VSF 320 SHELL Omala S4 WE 320
The dynamic efficiency is 0.98 for all ratios* The nominal power should be reduced if the ambient temperature is ≥ 30°C, or when a cooler gearbox is required.
411I Rating - Stainless Steel ONE STEP GEARBOXES
26
IMPORTANT INFORMATION
Please Read CarefullyThe following WARNING and CAUTION information is supplied to you for your protection and to provide you with many years of trouble free and safe operation of your product.Read ALL instructions prior to operating reducer. Injury to personnel or reducer failure may be caused by improper installation, maintenance or operation.
WARNING:• Written authorisation is required to operate or use reducers in man lift or people moving devices.• Check to make sure that certain applications do not exceed the allowable load capacities, published in the current catalogue.• Buyer shall be solely responsible for determining the adequacy of the product for any and all uses to which Buyer shall apply the product. The application by Buyer shall not be subject to any implied warranty of fitness for a particular purpose.• For safety, Buyer or User should provide protective guards over all shaft extensions and any moving apparatus mounted thereon. The User is responsible for checking all applicable safety codes in his area and providing suitable guards. Failure to do so may result in bodily injury and/or damage to equipment.• Gearboxes operating in a high position should have a protective shield for any possible parts falling down, for casual accidents where people are moving under them.• Hot oil and reducers can cause severe burns. Use extreme care when removing lubrication plugs and vents.• Make certain that the power supply is disconnected before attempting to service or remove any components. Lock out the power supply and tag it to prevent unexpected application power.• Reducers are not to be considered fail safe or self-locking devices. If these features are required, a properly sized, independent holding device should be utilised. Reducers should not be used as a brake.• Any brakes that are used inconjunction with a reducer must be sized or positioned in such a way so as to not subject the reducer to loads beyond the catalogue rating.• Lifting supports, including eyebolts, are to be used for vertically lifting the gearbox only and not other associated attachments or motors.• Use of an oil with an EP additive on units with backstops may prevent proper operation of the backstop. Injury to personnel, damage to the reducer or other equipment may result.• Overhung loads, subject shaft bearings and shafts to stress which may cause premature bearing failure and or shaft breakage from bending fatigue, if not sized properly.
Our company will not be responsible for any direct or indirect damages, caused by wrong use of the products or fornot observing the manuals.
Congratulations and thank you for selecting a Marathon Gearbox. Your new Marathon Gearbox is protected by a 2 year manufacturers warranty, effective from the invoice date of purchase.
Please retain your invoice as proof of purchase.
27
MALAYSIATorin Industries SND BHD (MALAYSIA) No. 6536A Jalan Bukit KemuningBatu 6 Seksyen 3440470 Shah Alam SelangorT: +60 3 5124 6157F: +60 3 5121 1467SINGAPORECMG Electric Motors (Asia Pacifi c) Pte Ltd12 Tuas Loop 637346SINGAPORET: +65 6863 3473F: +65 6863 3476THAILANDFASCO Motors (Thailand) Limited29/7-8 Bangkruay-Sainoi RoadBangkrangMuang Nonthaburi District Nonthaburi 11000THAILANDT: +66 2447 3300F: +66 2447 3500
Regal Beloit Australia Pty Ltd ABN 61 122 303 084
19 Corporate Ave (PO Box 2340)Rowville VIC 3178, AUSTRALIACustomer Service: 1300 888 853Fax: +61 3 9237 4010
www.regalaustralia.com.au
VICTORIA / HEAD OFFICE19 Corporate AvenueRowville VIC 3178T: 1300 888 853F: +61 3 9237 4050NEW SOUTH WALES6-7 Bushells PlaceWetherill Park NSW 2164T: 1300 888 853F: +61 2 8781 3131QUEENSLAND7 Mahogany CourtWillawong QLD 4110T: 1300 888 853F: +61 7 3246 3210CAIRNS (Service • Repairs • Sales)2/159-161 Newell StreetBungalow QLD 4870T: 1300 888 853F: +61 7 4033 5553MACKAYShed 5/58 Elvin StreetPaget QLD 4740T: 1300 888 853F: +61 7 4952 6277SOUTH AUSTRALIA47 Research RoadPooraka SA 5095T: 1300 888 853F: +61 8 8359 5675WESTERN AUSTRALIA21 Colin Jamieson DriveWelshpool WA 6106T: 1300 888 853F: +61 8 6253 3710
NEW ZEALANDAUCKLANDRegal Beloit New Zealand Ltd18 Jomac PlaceAvondaleT: 0800 676 722F: +64 9820 8504ROTORUA51 Purura StreetRotoruaT: 0800 676 722F: +64 7347 8629
APPLICATION CONSIDERATIONS
The proper selection and application of power transmission products and components, including the related area of product safety, is the responsibility of the customer. Operating and performance requirements and potential associated issues will vary appreciably depending upon the use and application of such products and components. The scope of the technical and application information included in this publication is necessarily limited. Unusual operating environments and conditions, lubrication requirements, loading supports, and other factors can materially affect the application and operating results of the products and components and the customer should carefully review its requirements. Any technical advice or review furnished by Regal Beloit Australia Pty Ltd and its affi liates with respect to the use of products and components is given in good faith and without charge, and Regal assumes no obligation or liability for the advice given, or results obtained, all such advice and review being given and accepted at customer’s risk.
For a copy of our Standard Terms and Conditions of Sale, Disclaimers of Warranty and Limitation of Liability, please contact Customer Service at 1300 888 853 or visit www.regalaustralia.com.au. These terms and conditions of sale, disclaimers and limitations of liability apply to any person who may buy, acquire or use a Regal Beloit Australia Pty Ltd product referred to herein, including any person who buys from a licensed distributor of these branded products.
Marathon Gearboxes and Regal are trademarks of Regal Beloit Australia Pty Ltd or one of its affiliated companies.
©2016, 2016 Regal Beloit Australia Pty Ltd, All Rights Reserved. MCC16022E • Form# 9999E • Created in AU
top related