syllabus of one year conventional course …ls1.and.nic.in/industry/skill dev/syllabustrades.pdf ·...
Post on 14-Apr-2018
215 Views
Preview:
TRANSCRIPT
SYLLABUS OF ONE YEAR CONVENTIONAL COURSE
FOR THE TRADE OF
GENERAL ENGINEERING
BY
DIRECTORATE OF INDUSTRIES
ANDAMAN AND NICOBAR ADMINISTRATION
COURSE CONTENTS
Practical Competencies Theory
1st Month
Identification and use of tools and equipments like measuring tools, marking tools, cutting tools, holding tools and machineries (lathe machine, drilling machine, cutters, grinder machine etc.) and welding plants (Gas/Arc) etc.
Use of marking media, marking, filing centre punching, dot punching, cutting, drilling, tapping and making of fitting jobs etc.
Importance of safety and general precautions observed in the workshop/Institute and in the section
Importance of Science and Calculation to the trade skill and fundamental Arithmetical operations, Addition, Subtraction, Multiplication and Division.
2nd month
Practicing of different types of weld joints and different types of weld beads.
b) Preparation of job edges according to the job carrying load.
c) Practicing and making all different types of fabrication works.
Definition of speed, velocity, acceleration, mass, weight and difference between mass and weight.
Importance of Engineering, Drawing and its knowledge.
Use of Drawing Instruments.
Freehand sketching of straight lines, rectangles, circle, polygons etc.
Construct an orthographic projection from the given isometric view of shaped blocks in 3rd angle method.
3rd and 4th Month
Practicing of marking, punching, riveting and soldering etc.
Making of sheet metal joints, tray, mug, funnel, haven gunt, trunk box, door and windows etc.
Practicing and making all different types of fabrication works.
1. ENGINEERING METALS:-
Physical properties.
Mechanical properties. SHEET METAL WORK:-
a) Sheet metal hand tools. b) Sheet metal bench tools. c) Sheet metal machine tools. d) Sheet metal operations. e) Sheet metal joints. f) Soldering and brazing.
5th and 6th Month
Straight and wearing beads on MS
in Flat position.
Preparation of joints, edge
preparation.
Fillet Lap & T joints
Inside corner joint
Square butt joint
Single ‘V’ but joint
Identification of defects by Visual
inspection & correction of defects. Practicing and making all different
types of fabrication works.
WELDING (GAS AND ARC):-
Welding methods.
Gas and Arc welding tools and equipments.
Welding joints, bead and preparation of Edges.
Safety precautions for gas and arc welding.
7th and 8th month
Making and practicing of lathe cutting tools clearance angle (FCA, FSCA, BSCA, BCA) etc.
Practicing of Turning, facing and thread cutting (internal and external) etc.
Making Nut and bolt, pushes and round wheels etc.
Practicing and making all different
LATHE MACHINE:-
Types of lathe machines.
Accessories of lathe machines.
Lathe operations (outer operation and Inner operation)
Lathe cutting tools according to shape.
Lathe cutting tools according to work.
types of fabrication works.
9th and 10th Month
Dismantling and assembling
automobile engine, clutch, gear box,
rear axle etc.
Hot forging and cold forging in
Blacksmity
AUTOMOBILE MECHANISM:-
Engine operations.
Lubrication and cooling system of engine.
Suspension system.
Power transmission system of Automobile.
MECHANICAL POWER TRANSMISSION:-
Power transmission by year’s.
Types of Gear’s.
Power transmission by chain and sprocket.
Use of belts in power transmission.
Introduction to Blacksmithy
11th Month
Project Work : Individual
preparation of project work by
the trainees which will be
assessed for internal marks
Industrial visit
12th month
Exposure training in Fabrication units
with updated machines
As approved by:-
A&N Administration Port Blair
Issued by:-
Directorate of Industries A&N Administration Port Blair
General Information 1. Name of the trade :- General Engineering Trade (GET) 2. Duration of Training :- 01 Year
3. Entry Qualification :- Passed the 10th Class Examination Under 10+2 system of Education or its equivalent
4. Age Limit :- 18-35 years
01 WEEK:- Importance of safety and general precautions observed in the workshop/Institute and in the section.
01 WEEK:- Identification and use of tools and equipments like measuring tools, marking
tools, cutting tools, holding tools and machineries (lathe machine, drilling machine, cutters, grinder machine etc.) and welding plants (Gas/Arc) etc.
04 WEEKS FILING PRACTICE:- Use of marking media, marking, filing, centre punching, dot
punching, cutting, drilling, tapping and making of fitting jobs etc. 02 WEEKS WORKSHOP CALCULATION AND ENGINEERING DRAWING:-
a) Importance of Science and Calculation to the trade skill and fundamental Arithmetical operations, Addition, Subtraction, Multiplication and Division.
b) Definition of speed, velocity, acceleration, mass, weight and difference between mass and weight.
c) Importance of Engineering, Drawing and its knowledge. d) Use of Drawing Instruments. e) Freehand sketching of straight lines, rectangles, circle, polygons etc. f) Construct an orthographic projection from the given isometric view of shaped
blocks in 3rd angle method.
10 WEEKS :- THEORY 2. SHEET METAL WORK:-
g) Sheet metal hand tools. h) Sheet metal bench tools. i) Sheet metal machine tools. j) Sheet metal operations. k) Sheet metal joints. l) Soldering and brazing.
3. LATHE MACHINE:- a) Types of lathe machines. b) Accessories of lathe machines. c) Lathe operations (outer operation and Inner operation) d) Lathe cutting tools according to shape. e) Lathe cutting tools according to work.
4. WELDING (GAS AND ARC):-
a) Welding methods. b) Gas and Arc welding tools and equipments. c) Welding joints, bead and preparation of Edges. d) Safety precautions for gas and arc welding.
5. AUTOMOBILE MECHANISM:-
a) Engine operations. b) Lubrication and cooling system of engine. c) Syspension system. d) Power transmission system of Automobile.
6. MECHANICAL POWER TRANSMISSION:-
a) Power transmission by year’s. b) Types of Gear’s. c) Power transmission by chain and sprocket. d) Use of belts in power transmission.
7. ENGINEERING METALS:-
a) Physical properties. b) Mechanical properties.
PRACTICAL 30 WEEKS:- 1. a) Practicing of marking, punching, riveting and soldering etc. b) Making of sheet metal joints, tray, mug, funnel, haven gunt, trung box, door
and windows etc. 2. a) Making and practicing of lathe cutting tools clearance angle (FCA, FSCA,
BSCA, BCA) etc. b) Practicing of Turning, facing and thread cutting (internal and external) etc. c) Making Nut and bolt, pushes and round wheels etc. 3. a) Practicing of different types of weld joints and different types of weld
beads. b) Preparation of job edges according to the job carring loard. c) Practicing and making all different types of fabrication works.
4. a) Dismantling and assembling of automobile engine, clutch, gear box, rear axle etc.
x------- x-------x------x-------x-------x---------x--------x
SYLLABUS OF ONE YEAR CONVENTIONAL COURSE
FOR THE TRADE OF
TAILORING AND GARMENT MAKING
BY
DIRECTORATE OF INDUSTRIES
ANDAMAN AND NICOBAR ADMINISTRATION
MONTH THEORY PRACTICAL
1st Adventure of sewing machine and importance of Tailoring in Daily Life and its commercial values
Theoretical knowledge on Operation of Sewing machine
o Hand sewing machine, o Tradle sewing machine o Electric sewing machine.
Various types of hand stitches Preparation of fair Theory & Drafting
files.
Introduction for using of sewing machine.
Practice – How to operate the sewing machine.
Knowledge of sewing machine parts and its functions.
Maintenance and oiling of machinery. Basic hand stitches - Hemming stitch,
Back stitch, Half back stitch, Even stitch, Uneven stitch, Running stitch etc.
Hand Embroidery stitches – Hearing bone stitch , fish bone stitch, shadow stitch, whipped chain stitch, bullion stitch etc.
2nd Theoretical knowledge on Sewing Machine and its parts -
o Balance wheel, spool pin, pressure foot, needle bar, pressure foot lifter, feed dog , stitch regulator etc.
Various kinds of Hand Embroidery stitches –
Kinds of Basic seams and its applications
Difference between Inches & cms. Preparation of fair Practical files.
Basic seams – Plain seam, French seam, flat seam, zig-zag seam, Bound seam, self bound seam, pinked seam etc.
Demonstration and Practice – How to take Upper and lower body measurement
Demonstration & practice of Drafting, Paper cutting & stitch practice of various sample garments
Requirement & method of cutting cloth as per measurement.
Method of taking measurement of body calculation
3rd Description of Tools & Equipment –
(i) Measuring tools & equipment (ii) Drafting tools & equipment (iii) Cutting tools & equipment (iv) Sewing tools & equipment (v) Pressing tools & equipment
Some more Hand Embroidery stitches –
Double chain stitch, stem stitch, Bullion
laisy-daisy stitch, Blanket stitch, Button
stitch, semi running stitch, Gujrati
stitch etc.
Paper pattern and lay out on the cloths
and complete these by applying different
2. Abbreviations on Drafting 3. Drafting method of upper &
lower body garment. Drafting & paper pattern of saree
petticoat, Gents kurta & pajama, etc.
4. 1st terminal test for theory. (MM 25)
style of stitches.
Stitch & Hand Embroidery work on
Pillow cover etc.
Basic Neck lines & Piping neck lines-
Demonstration of petticoats
o 1st Terminal test for Practical.
(MM 25)
4 th Drafting of child body block
Drafting & paper pattern of different types of collars-
Maintenance of sewing machine
Cleaning & oiling of sewing machine -
Renovation of Cloths- Darning by hand machine, darning patching
Drafting & paper pattern of Kids wear - Baby frock, ‘A’ Line skirt, straight skirt, tight skirt , half circular skirt, full circular skirt, novelty skirt etc.
Measurement chart- o Measurement chart for kids ,
Ladies & Gents.
Designing of Box pleat skirt, Inverted pleat skirt, Designer skirts, baby frock and baby tops etc.
Designing of Kids wear - like Baby frock, ‘A’ Line skirt, straight skirt, tight skirt, half circular skirt, full circular skirt, novelty skirt etc.
5th Different types of pleats-
Different types of tucks
Drafting & Paper pattern of different types sleeves – plain sleeve, puff sleeve, flair sleeve, Magyar sleeve, kimono sleeve etc.
Drafting & paper cutting of Ladies kurties , suit, frock suit etc.
How to take measurement –full length, shoulder, chest round, waist round, hip round, seat, ankle round, sleeve length, color etc.
Cutting & stitching for designer Ladies kurties , suit, frock suit etc. of different sizes
Demonstration of various types of tucks
Demonstration and making samples of knitting work and crochet work with wool and lace
6th Sewing needles and threads – o Various kinds Hand needle and
Machine needle available and its applications
Functions and operations of various Machine attachment parts
Drafting & paper pattern of plain salwar, kalidar salwar, patiyala, ladies kurtis etc.
1. 2nd terminal test for theory. (MM 25)
Demonstration of machine coaching stitch , shell stitch and form stitch and making of related samples
Demo of Cutting & stitching of plain salwar, kalidar salwar, chudidar salwar etc. and making of related samples
2nd terminal test for Practical. (MM 25)
7th Theoretical knowledge on Textile Designing – Block print , spray print, vegetable print, stencil printing, fabric
Practical Demonstration of Textile Designing in various kinds of cloths and fabrics–
print etc. Including Tie & dye
(i)Block print . (ii) spray print, (iii) vegetable print. (iv) stencil printing.
(vi) fabric print etc. (vii) Tie and dye etc.
8th Sewing machine faults and their rectification:-
Different patterns of design – o Vertical pattern, horizontal
pattern, diagonal pattern, asymmetrical pattern
o Brick pattern etc.
Design development and Demonstrations of designer dresses
Using shell, beads and other accessories
Project work -
Creating individual designer samples with fusion of shells, beads tec.
9th Drafting & paper pattern of apron feed `er, plain blouse, six cut blouse, back hook blouse
Drafting & paper pattern of night gown, night dress, house coat
3rd terminal test for theory. (MM 25)
Cutting and stitching of apron, feeder, plain blouse, six cut blouse, back hook blouse etc.
Cutting and stitching of designer night gown and housecoat.
3rd terminal test for practical. (MM 25)
10th Study of different types of human body
Principle s of paper pattern making
Drafting & paper pattern of Half pant, Half sleeve shirt.
Drafting & paper pattern of Full pant and full sleeve shirt.
Cutting & stitching of Half pant and Half sleeve shirt.
Cutting & stitching of full pant and full sleeve shirt.
11th Removal of stains –
Stain of machine oil, tea stain, ink stain ,ghee stain, boot polish stain, blood stain etc.
Information on Dictionary of tailoring
How to Handle fashion maker and advanced sewing machines.
Market survey on various kinds of fabrics
12th Revision of the course studies during the session.
Correction of theory and drafting files.
Conducting final theory test by instructress.
Presentation in Practical records and final touch to all the practical works conducted during the entire session.
Marking of practical records
Final practical test by Instructress .
As approved by:-
A&N Administration
Port Blair
Issued by:-
Directorate of Industries
A&N Administration
Port Blair
SYLLABUS OF ONE YEAR CONVENTIONAL COURSE
FOR THE TRADE OF
CANE AND BAMBOO HANDICRAFTS
BY
DIRECTORATE OF INDUSTRIES
ANDAMAN AND NICOBAR ADMINISTRATION COURSE CONTENTS
Theory Practical
1st Month
Introduction of Cane & Bamboo for its used and identification of different type of Cane & Bamboo available in Andaman & Nicobar Islands and study of catalogue and design for making of furniture and Handicrafts.
Description of Bamboo and its used to production of Handicrafts and furniture.
Practical/ Hands on works experience under the guidance of Instructor/worker:-
Cane & Bamboo strips processing and making or extension of Bamboo and Cane strips.
Cane knitting on the chair, chatai (Mat] and Bamboo knitting on the different type of chatai (Mat].
2nd and 3rd Month
Introduction about the tools and machinery used in the Cane & Bamboo Handicrafts and furniture and own safety measures to be adopted while working with the tools and machinery with drawing for tools.
Introduction and description of different type of tools use for production of Cane and Bamboo Handicrafts and furniture.
Practice of Cane joint making of different type and different type of Cane binding for handicraft and furniture.
Manufacturing of different type of Handicraft and furniture.
Manufacturing of different type of Handicraft and decorative items and furniture for Cane and Bamboo.
Preparation of products independently without assistance from instructor workers under overall supervision of Instructor and made for job and estimate.
4th and 5th month
Different treatment used to processing Cane & Bamboo.
Bending of Cane & Bamboo method of different shapes
Preservation of Bamboo
Use of Borax & Boric Acid, use of Smoke chamber and other Chemical Process. Practice of Traditional
for use of furniture and Handicraft items.
Coloring, painting, varnishing on Cane & Bamboo items, Brush painting and spray painting etc.
Finishing of Cane & Bamboo surface of furniture and Handicraft before painting and varnishing.
Estimating and noting of finished products.
process
Practice of dying utilizing various chemical & vegetative dyes.
Preparation of products independently without assistance from instructor workers under overall supervision of Instructor and made for job and estimate
How to behave with customer as
entrepreneur
Communication skills that are useful
to customer service are identify in
accordance with enterprises
requirements.(speaking, giving
information, active listening)
6th and 7th Month
Joints: Briefing about various joints, method of joints, uses of joints.
Introduction: Use of various Household and Public furniture, Advantage of sketch making of various furniture designs
Brief description of electric Drill
Machine and how to operate trouble
shooting of this machines
Brief description of 2 side/4 side
planer machine and how to operate
trouble shooting of this machine`
Joints
Practice in tongue and groove or male and female joint, Bolt fastening joint. Overlapping joint, U-shape joint. Horizontal joint, Vertical joint etc.
Types of Furniture
Demo of various type of furniture, Draw the Neat sketch of furniture
Drill Machine
Practice of operation in electric drill
machine, oiling and lubrication of
machine
Practice of operation in 2 side/4 side
machine planer, oiling and lubrication
of machine including preventive
maintenance
8th and 9th Month
How to make pattern, banding, buffing, and polishing of bamboo.
Various joineries used in furniture making process
Use of Blow lamp
Practice of pattern making, use of blow lamp and it precaution.
Practice of furniture making
Fusion of coconut, shell and bamboo handicrafts
Calculation of cost of finished Bamboo.
top related