telescopic pole mount ce-cm-s-2 ce-cm-sx-6clinton electronics 6701 clinton road loves park, il 61111...
Post on 06-Oct-2020
0 Views
Preview:
TRANSCRIPT
CLINTON Electronics6701 Clinton RoadLoves Park, IL 61111
1.800.447.3306 Sales1.800.549.6393 Support1.800.633.8712 Fax
www.clintonelectronics.com
Telescopic Pole MountCE-CM-S-2CE-CM-SX-6CE-CM-SX-8CE-CM-LX-12CE-CM-LX-17
User Manual
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
WARNINGPrior to installation and use of this product, please observe the following warnings:1. Installation and servicing should be done by qualified personnel, and all work done should conform to local codes.2. Using replacement parts or accessories other than from the manufacturer may void the warranty.
CAUTIONCHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&FAC24V
AUX1 AUX2
COM
ALM
1
ALM
2
ALM
3
ALM
4
ALM
5
ALM
6
ALM
7
485A
485B
485A
485B AC24V
AC220V
AC220V
COM
JP2 JP2_2
AC24V FUSE
J1
FUSE5X20
Outdoor BoxModel CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Outdoor BoxModel CE-PTZ-WP24
0204201792
LM1
LM2
LM3
LM4
LM5
LM6
LM7
85A85B
85A85B AC24V
OM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&FAC24V
AUX1 AUX2
COM
ALM
1
ALM
2
ALM
3
ALM
4
ALM
5
ALM
6
ALM
7
485A
485B
485A
485B AC24V
AC220V
AC220V
COM
JP2 JP2_2
AC24V FUSE
J1
FUSE 5X20
Outdoor BoxModel CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AUX1 AUX2
COM
ALM
1
ALM
2
ALM
3
ALM
4
ALM
5
ALM
6
ALM
7
485A
485B
485A
485B AC24V
AC220V
AC220V
COM
JP2_2
AC24V FUSE
J1
FUSE 5X20
Outdoor BoxModel CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&FAC24V
AUX1 AUX2
COM
ALM
1
ALM
2
ALM
3
ALM
4
ALM
5
ALM
6
ALM
7
485A
485B
485A
485B AC24V
AC220V
AC220V
COM
JP2 JP2_2
AC24V FUSE
J1
FUSE5X20
Outdoor BoxModel CE-PTZ-WP24
0204201792
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
Telescopic LCD ceiling mount Info:
This bracket is designed to mount to mount an LCD from the ceiling structure. It can be used with the existing truss structure of the building or in conjunction with channel strut.There are four lengths of brackets available:• Part # CM-S-2 Length of 22” to 35”• Part # CM-SX-6 Length of 36” to 67”• Part # CM-SX-8 Length of 54” to 96”• Part # CM-LX-12 Length of 71” to 139”• Part # CM-LX-17 Length of 75” to 200”(Brackets are identical except for length)
Included Hardware:
Tools Required:7/16” wrench7mm wrench10mm wrench3/4” wrench5/16” wrench#2 Phillips head screwdriverlevel
1/4”-20 x 2” hex head bolt (1 pc.), lock washer (1 pc.), washers (2 pcs.), and locknut (1 pc.)
Please check to ensure all hardware is included prior to installation. If parts are missing, please contact Clinton Electronics for replacement parts.
1/2”-13 lock nut (1 pc.), and fender washer (1 pc.)
M4 x 45 screw (1 pc.),washers (2 pcs.), and locknut (1 pc.)
M4 x 10mm screwto attach safety cableto rear of display. (1 pc.)
Safety cable with crimped eyelet. (1 pc.)
U-bolt cableclamp. (1 pc.)
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
User Manual(1 pc.)
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Bracket (1 pc.)
Pole MountAssembly (1 pc.)
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
AC24VIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&FAC24V
AUX1 AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A +
485B -
485A +
485B -
AC24V
AC220V
AC220V
COM
JP2JP2_2
AC24V FUSE
J1
FUSE5X20
Alarm Inputs
485 Inputs
Ground
24V Input
Auxilary Inputs
Common
Common
220V Aux. Input
Alarm/Aux/ComOutput 1 to Camera
AC24V Outputto Camera
AC24V Aux. Input
5 x 20mm fuse3A 250V
RS485 CommunicationOutput to Camera
Heater &Fan Output
JP9
NOT USED WITH STANDARD SETUP
220V Aux. InputAlarm/Aux/ComOutput 2 to Camera
IN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&FAC24V
AUX1 AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A
485B
485A
485B AC24V
AC220V
AC220V
COM
JP2JP2_2
AC24V FUSE
J1
FUSE5X20
Outdoor Box
Model CE-PTZ-WP240204201792
2.12 in (54mm)
9.41
in (2
39m
m)
.39 in (9.9mm)
7.94
in (2
02m
m)
4.48 in (114mm)
6.10 in (155mm)
8.46
in (2
15m
m)
6.69
in (1
70m
m)
JP9
5.55 in (141mm)
AC24VIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1
AUX2
COMALM1 ALM2 ALM3 ALM4 ALM5 ALM6 ALM7
485A + 485B - 485A + 485B - AC24V
AC220V
AC220V
COM
JP2
JP2_2
AC24V FUSE
J1
FUSE
5X20
Alarm Inputs
485 Inputs
Ground
24V Input
Auxilary Inputs
Comm
on
Comm
on
220V Aux. Input
Alarm/Aux/Com
Output 1 to Camera
AC24V Output
to Camera
AC24V Aux. Input
5 x 20mm
fuse
3A 250VRS485 Comm
unication
Output to Camera
Heater &
Fan Output
JP9
NOT USED WITH STANDARD SETUP
220V Aux. Input
Alarm/Aux/Com
Output 2 to Camera
IN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1
AUX2
COMALM1 ALM2 ALM3 ALM4 ALM5 ALM6 ALM7
485A 485B485A 485B AC24V
AC220V
AC220V
COM
JP2
JP2_2
AC24V FUSE
J1
FUSE
5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
2.12 in (54mm
)
9.41 in (2
39mm)
.39 in (9.9mm
)
7.94 in (2
02mm)
4.48 in (114mm
)
6.10 in (155mm
)
8.46 in (2
15mm)
6.69 in (1
70mm)
JP9
5.55 in (141mm
)
M4 x 8 VESA screws(4 pcs.)
Assembly InstructionsTruss mount or channel strut mount
Securing Mount to Building:1. Insert threaded rod between truss gap or into hole in channel strut.
2. Place 1/2” fender washer over the threaded rod and then 1/2” lock nut.
3. Tighten the 1/2”-13 lock nut using a 3/4” wrench.
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Mounting LCD to Pole:1. If your LCD is supplied with a VESA plate already mounted on the back, simply ensure the four M4 screws are in place and tightened. If the mount is not already attached, connect it using the supplied M4 x 8mm VESA screws (4-places).*NOTE: Some installations may require running power and video cables prior to attaching the LCD bracket to the pole. If this is the case, do sobefore continuing to step 2.
2. Hold the LCD with attached bracket up to the end of the pole mount, andline up the wings of the bracket to the holes in the end of the pole. Insert the1/4”-20 x 2” bolt, lock washer, washers, and lock nut in place according to the illustration on the right. You will use 7/16” and 10mm wrenches to fully tighten in step 4.
3. Install the M4 x 45mm screw, washers, and lock nut into the upper slotted hole according to the illustration on the right. You will use a #2 Phillips screwdriver and a 7mm wrench to fully tighten in the next step.
4. Tighten the fasteners to secure the monitor at the desired angle.*NOTE: Avoid overtightening which can cause the pole to indent.
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Leveling the Pole1. You can ensure the pole is plumb by tightening the 1/4”-20 lock nuts on the top of the pole where it attaches to the structure using a 7/16” wrench.
2. Place a level on the pole and tighten the nuts that correspond to the direction that the pole needs to move (see illustration on the right).
3. Check and adjust 2 adjacent sides of the pole until it is plumb in each direction.
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mmVESA screw(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer1/4” Washer
M4 Washer
Pole will move inthe direction of thetightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Remove originalM4 x 8mm VESAscrew & replace withM4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section andturn counter-clockwise to loosen
Prevent display from falling byholding lower pole section here
Secure assembly by turning collar clockwise:hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.Use with products heavier than the maximum weights indicated may result ininstability causing possible injury. This product is intended to mount to a steelsupport truss, or channel strut.
9/16
”
If dr
illin
g is
nec
essa
ry,
Use
9/1
6” m
etal
dri
llbi
t to
drill
thro
ugh
stee
lm
ount
ing
surf
ace.
Max Load:15kgs / 35lbs.
Remove original
M4 x 8m
m VESA
screw &
replace with
M4 x 10m
m screw
U-Bolt Cable Clam
p
Cord Managem
ent Hole
Hold low
er pole section andturn counter-clockw
ise to loosen
Prevent display from falling by
holding lower pole section here
Secure assembly by turning collar clockw
ise:hand tighten as snug as possible
CAU
TION
: This stand is intended for use only with the m
aximum
weights indicated.
Use w
ith products heavier than the maxim
um w
eights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
9/16”
If drilling is necessary,Use 9/16” metal drillbit to drill through steelmounting surface.
CLINTON Electronics6701 Clinton RoadLoves Park, IL 61111
1.800.447.3306 Sales1.800.549.6393 Support1.800.633.8712 Fax
www.clintonelectronics.com
Remove originalM4 x 8mm VESAscrew & replace withM4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section andturn counter-clockwise to loosen
Prevent display from falling byholding lower pole section here
Secure assembly by turning collar clockwise:hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.Use with products heavier than the maximum weights indicated may result ininstability causing possible injury. This product is intended to mount to a steelsupport truss, or channel strut.
9/16
”
If dr
illin
g is
nec
essa
ry,
Use
9/1
6” m
etal
dri
llbi
t to
drill
thro
ugh
stee
lm
ount
ing
surf
ace.
Installing the Safety Cable:1. Run the safety cable into the cable management hole in the top of the pole, and out through the bottom of the pole. The crimped eyelet end will connect to the LCD.
2. Remove one of the M4 x 8mm VESA mount screws from the LCD-bracket assembly, then connect the crimped eyelet end of the safety cable to the mount using the supplied M4 x 10mm screw. You can discard the unused M4 x 8mm VESA mount screw that has been removed as it is no longer needed.
3. Connect the top end of the safety cable by inserting it through a hole in the truss or channel strut, and fasten using the U-Bolt cable clamp. Pull any remaining slack from the safety cable, and fully tighten the U-Bolt using a 5/16” wrench. Cut or loop any excess cable.
Adjusting Height:1. Hold the lower pole (where it connects to the LCD) while loosening the center collar by turning it counter-clockwise (see illustration on left below). Extend the pole by gently lowering it to the desired length.
2. Once the proper length has been maintained, lock the pole in position by rotating the center collar clockwise. The collar should be hand tightened as snug as possible to prevent the pole from expanding. (see illustration on right below)
Remove originalM4 x 8mm VESAscrew & replace withM4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section andturn counter-clockwise to loosen
Prevent display from falling byholding lower pole section here
Secure assembly by turning collar clockwise:hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.Use with products heavier than the maximum weights indicated may result ininstability causing possible injury. This product is intended to mount to a steelsupport truss, or channel strut.
9/16
”
If dr
illin
g is
nec
essa
ry,
Use
9/1
6” m
etal
dri
llbi
t to
drill
thro
ugh
stee
lm
ount
ing
surf
ace.
Remove originalM4 x 8mm VESAscrew & replace withM4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section andturn counter-clockwise to loosen
Prevent display from falling byholding lower pole section here
Secure assembly by turning collar clockwise:hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.Use with products heavier than the maximum weights indicated may result ininstability causing possible injury. This product is intended to mount to a steelsupport truss, or channel strut.
9/16
”
If dr
illin
g is
nec
essa
ry,
Use
9/1
6” m
etal
dri
llbi
t to
drill
thro
ugh
stee
lm
ount
ing
surf
ace.
Remove originalM4 x 8mm VESAscrew & replace withM4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section andturn counter-clockwise to loosen
Prevent display from falling byholding lower pole section here
Secure assembly by turning collar clockwise:hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.Use with products heavier than the maximum weights indicated may result ininstability causing possible injury. This product is intended to mount to a steelsupport truss, or channel strut.
9/16
”
If dr
illin
g is
nec
essa
ry,
Use
9/1
6” m
etal
dri
llbi
t to
drill
thro
ugh
stee
lm
ount
ing
surf
ace.
Loosen Tighten
v.04.06.11
top related