total gym pedestal
Post on 04-Jun-2018
227 Views
Preview:
TRANSCRIPT
-
8/13/2019 Total Gym Pedestal
1/23
-
8/13/2019 Total Gym Pedestal
2/23
A Pedestal Design for the Total Gym
Contents
Project Overview ........................................................................................................................................... 3
Bill of Materials, Tools and Suggestions ....................................................................................................... 5
Pedestal Assembly and Detail Drawings ....................................................................................................... 6
General Views of the Pedestal .................................................................................................................. 6
View of the Pedestal and the Total Gym showing Assembly Details ........................................................ 7
Dimensions of the Base............................................................................................................................. 8
Dimensions of the Angled Support ........................................................................................................... 9
Dimensions of the Top ............................................................................................................................ 10
Dimensions of the Upright ...................................................................................................................... 11
Dimensions of the U-Bolt ........................................................................................................................ 12
Some Close-Up Views of the 2 7/8 x 4 Pedestal and the Platform Weight Bar........................................ 13
Static Resistance Provided by the Pedestals Height.................................................................................. 15Height & Incline Comparison of the Total Gym 1000 Series and the Total Gym on the Pedestal .......... 15
Graph of the Static Resistance Presented to the User as % of Platform Load and Angle ...................... 16
Examples of Static Resistance vs Platform Load and Angle .................................................................... 16
Calculating the Force and Power Required to do the Prone Push-Down Exercise ..................................... 17
Details of an Example Prone Push-Down ................................................................................................ 17
Diagram of the Platform Forces .............................................................................................................. 17
Equations for Force and Power vs. Time for the Example Prone Push-Down Exercise .......................... 18
Calculating the Force and Power vs Time from the Platforms Acceleration and Velocity 19
-
8/13/2019 Total Gym Pedestal
3/23
Project Overview
The Total Gym 1000 series is a terrific piece of exercise equipment for strengthening the muscles used inthe canoe and kayak paddling motion. It allows a large variety of arm motions and requires engaging the
torso and back while using the arms. Some people using the Total Gym for paddling-related exercises
find that the exercise resistance available in the product is too small. This project provides details of a
pedestal that increases the exercise resistance. The exercise resistance comes from the angle of the
platform and the weight on the platform. Increasing the exercise resistance can be done either by
increasing the platforms angle so that a larger percent of the users weight is lifted or by adding weight
to the platform via attachment of a bar at the bottom edge of the platform for the addition of barbellplates or by doing both.
Here are drawings and photos of a pedestal I made to increase the platforms angle and with it the
exercise resistance. Along with the increased height the pedestal also improves the lateral stability by
increasing the width of the base by 68% (from 16 to 27). I have used this pedestal for about three
years and I found it is stable and rigid. Im quite happy with it. The motivation for increasing the
platforms angle via this pedestal is an alternative to the method used by Mr. Marc Gillespie (principal of
Forge Racing). Marc has the upper end of his Total Gym attached to a steel pole in his basement. Thepole is a structural support of the house, is about 4 in diameter and is commonly used in house
construction in this area. My house also has such support poles but there are none in a location
convenient for placing the Total Gym.
The finished pedestal looks like this:
http://www.forgeracing.org/http://www.forgeracing.org/http://www.forgeracing.org/ -
8/13/2019 Total Gym Pedestal
4/23
You are responsible for safety while using the Total Gym and any modifications you make to it. If you
increase the angle of the platform by simply putting the vertical support on top of something such as a
box then the vertical support wont be vertical and the Total Gym will be unstableand unreliable. Dont
use the Total Gym in an unstable or unreliable condition. Be aware that increasing the angle of the
platform causes increased load in the hand grips, cables, pulleys and fasteners. You are responsible fordetermining that your hand grips, cables, pulleys and fasteners are capable of handling the increased
load before you decide to use them.
The following pages show the materials, tools and parts used for making a pedestal from 4 x 4
dimensional lumber. What the lumber yards call 4 x 4 dimensional lumber is actually 3 x 3 when
it arrives in the hands of us users. You will see 3 x 3 on all the drawings. The pedestal shown in the
photo is the one I have used for several years and it is made from a large pallets stringer which is 27/8
x 4.In this paper Ive taken its design and adapted it to the more common 4 x 4dimensional lumbersize. In case youre wondering, I have not used 4 x 4 dimensional lumber and these drawings to build a
pedestal. The pedestal I made is from 2 7/8 x 4 lumber. If you find an error, missing dimension or have
a suggestion about this project please contact me.
A person could get the same static resistance increase by adding weight to the platform instead of
increasing the platform angle. Adding about 54% of your body weight to the platform will be statically
equivalent to increasing the platform angle the amount this pedestal affords. I found the standard Total
Gym is too unstable side-to-side when set to its maximum angle and the platform is moved aggressively.
Before I added more weight I wanted to add side-to-side stability. The platform added stability and
static resistance. Adding weight to the platform is a good idea only if the system is stable. The additional
weight requires that you apply additional force to accelerate it. After developing the pedestal I added a
bar and weights to the platform in the same way others have done. A detailed photo of the bar
attachment is at the end of this document.
Youre welcome to use this design for any non-commercial purpose. If you make one, you have the
responsibility for the quality and care with which you make it, the quality and care with which you
attach the Total Gym to it and the suitability of the whole system for any use you put it to.
In the pages after the design details there is an analysis of force and power involved in the prone push-
-
8/13/2019 Total Gym Pedestal
5/23
Bill of Materials, Tools and SuggestionsBill of Materials
4 x 4 x 10 Dimensional Lumber, Qty 1.............. (9 4 is needed, can be made from one 8 and one 4)
2U-bolts, Qty 2 ............................................... (for fastening the vertical uprights base to the pedestal)
x 3 Hex Head Lag Screws, Qty 7 ............................................. (for fastening the pedestal together)
I.D. x O.D. Flat Washers, Qty 11................................... (7 for the Lag Screws and 4 for the U-Bolts)
1 x 1 Right Angle Braces, Qty 2.................. (for positioning the lower end of the diagonal support)
1 Wood Screws, Qty 6.......................................... (for fastening the Right Angle Braces to the pedestal)
Wood Glue, Qty A/R ..................................................... (as required, for fastening the pedestal together)
Tools
Tape Measure
Carpenters Square
1/8 Drill Bit .................................................................................. (pilot holes for the x 3 lag screws)
Drill Bit ............................................................................ (clearance holes for the x 3 lag screws)
1 Auger Drill Bit ...................... (clearance holes for the 7/16 socket used on the lag screws and U-bolts)
Saw ..................... (Hand, Circular, Table or Bandwhatever suits you. I used a hand-held circular saw.)
Drill ..... (I used a battery powered portable for the1/8 and drills and a ratchet brace for the 1 drill)
7/16 Socket and Wrench......................................................... (tightening the lag screws and the U-bolts)
Protractor .................................................................................................................................... (optional)
Suggestions
-
8/13/2019 Total Gym Pedestal
6/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 6
Pedestal Assembly and Detail Drawings
General Views of the Pedestal
FRONT BACK
Back To Table of Contents
-
8/13/2019 Total Gym Pedestal
7/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 7
View of the Pedestal and the Total Gym showing Assembly Details
Back To Table of Contents
-
8/13/2019 Total Gym Pedestal
8/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 8
Dimensions of the Base
Back To Table of Contents
Section A View of
Clearance Holes
Diameter
Diameter 1
A
-
8/13/2019 Total Gym Pedestal
9/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 9
Dimensions of the Angled Support
Back To Table of Contents
-
8/13/2019 Total Gym Pedestal
10/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 10
Dimensions of the Top
Back To Table of Contents
Section B View of
Clearance Holes
Diameter
Diameter 1
Section A View of
Clearance Holes
Diameter
Diameter 1
A
B
Check your U-bolt
center-to-center
distance before
drilling these holes. I
notice the bolt
distance varies about
1/8
These holes are for the U-Bolts.
See the notes on the U-Bolt
dimensions page before drilling.
-
8/13/2019 Total Gym Pedestal
11/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 11
Dimensions of the Upright
Back To Table of Contents
-
8/13/2019 Total Gym Pedestal
12/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 12
Dimensions of the U-Bolt
Oddly enough, a 2 U-Bolt is intended to be used on a 1 pipe!
If your U-Bolt comes with a flat plate, just remove it. It doesnt get used.
Height of the bolt varies with manufacturer.
Typical height is 3" or 3 ".
The drawing for the TOP gives of thread
for the nut if you have a 3 bolt. And the bolt
will be clamping 1 of wood.
If you have a 3 bolt you might want to
clamp 1 of wood by shortening the depth
of the four 1 diameter holes to 2.
-
8/13/2019 Total Gym Pedestal
13/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 13
Some Close-Up Views of the 2 7/8 x 4 Pedestal and the Platform Weight Bar
The three attachment points of the Total
Gyms vertical upright to the Pedestal -Two U-bolts at the base. One lag screw
through an existing hole in the Total Gyms
vertical upright. Use the hole located about
13 up from the base of the Total Gym.
Bottom view of the recessed U-bolts
fasteners
Attachment of the diagonal
support to the pedestal
-
8/13/2019 Total Gym Pedestal
14/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 14
Bottom View of Platform Showing Attachment
of Additional Bar for Barbell Plates
Back View of Pedestal
-
8/13/2019 Total Gym Pedestal
15/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 15
Static Resistance Provided by the PedestalsHeight
The resistance of the Total Gym, like all free weights, has two components the static resistance and the dynamic resistance.
Static ResistanceThe static resistance is the force required to hold the platform load in any position. The static resistance is determined by the
platform load and the platform angle.
Dynamic ResistanceThe dynamic resistance is the force required to accelerate the platform load. The dynamic resistance is determined by the total
moving mass and the acceleration of that mass caused by the users applied force.
The static resistance is the minimum force the user will experience; the dynamic resistance is determined by the users effort ; and the sum
of them is the total resistance experienced by the user.
Height & Incline Comparison of the Total Gym 1000 Series and the Total Gym on the Pedestal
Total Gym 1000 Series Total Gym on Pedestal
Platforms Guide RailLength 89 Platforms Guide RailLength 89
Guide Rails Lowest Height 10 1/4 Rails Incline: 6.6 Guide Rails Lowest Height 42 Rails Incline: 28.2
Guide Rails Highest Height 37 7/8 Rails Incline: 25.2 Guide Rails Highest Height 58 1/4 Rails Incline: 40.9
Photos in appendix A were made while gathering these dimensions.
-
8/13/2019 Total Gym Pedestal
16/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 16
Graph of the Static Resistance Presented to the User as % of Platform Load and Angle
Examples of Static Resistance vs Platform Load and Angle
Users Weight (Lbs) Additional Weight (Lbs) Total Weight (Lbs) Platform Angle ()
Static Resistance (Lbs)
=Sin(Platform Angle) x Total Weight
160 0 160 38.1 99
160 40 200 38.1 123
185 0 185 40.9 121
185 50 235 40.9 154
Back To Table of Contents
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90
%ofPlatformL
oadPresentedtoUserasStaticRe
sistance
Platform Angle, Degrees
Static Resistance Presented to User as % of Platform Load and Platform Angle
Resistance as % of Platform Load= Sin(Angle)*100%
OnPedestal:H
ighest
OnPedestal:L
owest
Standard:Highe
st
Standard:Lowest
Use of the pedestal increases the maximum static resistance by
54%. Raising it from the standards maximum at 43% of
platform load to the w/pedestals maximum at 65% of the
platform load.
-
8/13/2019 Total Gym Pedestal
17/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 17
Calculating the Force and Power Required to do the Prone Push-Down ExerciseThe motion of the prone push-down exercise is very similar to the top hand motion of the canoe stroke. That similarity makes it great for training. It is
possible to calculate how much force and how much power are used to do this exercise. The calculated power can be thought of as the top hands
potential for propelling a canoe. Many people advocate the top hands
power to be critical in developing canoe speed. That thought leads to
asking: At a given speed of a tandem canoe, what percentage of the
required per-person power is equal to the top hands power potential? Inthe next few pages Ill develop an answer to that question and the
question of force needed to do this exercise.
For starting out, here is a list of the information I know:
Details of an Example Prone Push-Down
Diagram of the Platform Forces
Here is a simple diagram of the platform and the forces acting on it:
Angle of Platform 38.1 degrees
Users Weight 160.0 lbs
Added Platform Weight 40.0 lbs
Platform Travel (observation) 18.5 inchesPlatform Starting Speed (at the bottom) 0.0 in/s
Platform Ending Speed (at the top) 0.0 in/s
Travel Time, bottom to top (observation) 0.5 Seconds
Acceleration due to Gravity 386.4 in/s2
1) Push Down
2) Platform Moves Up
Prone Push-Down Exercise on a Total Gym with Pedestal and
Additional Platform Weight
Total Platform Mass x Acceleration due to Gravity = Force of Gravity
MTotalx g =Fgravity
38.1
Applied Force as Function of Time = F(t)
-
8/13/2019 Total Gym Pedestal
18/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 18
Equations for Force and Power vs. Time for the Example Prone Push-Down Exercise
I want to know what the applied force is as a function of time. There are only two forces tha t act along the platforms line of travel. Those are the
applied force and a portion of the force of gravity. Notice that they act in opposite directions, so we can call the direction of the applied force
positiveand the direction of the portion of the gravity force that acts along the platforms line of travelnegative. Let Mtotalrepresent the total
mass on the platform and g represent the vertical acceleration due to gravity. The portion of the force of gravity that is acting along the platforms
line of travel is equal to Cosine(90-38.1) x Mtotalx g. Since the cosine and the sine are 90apart we can write that as sin(38.1) x Mtotalx g. Sir Isaac
Newton pointed out that the sum of all the forces acting on a body and along any one line of action equals the time rate of change of the bodysmomentum (momentum equals mass x velocity) along that line of action. Thats the long way of saying the familiarand simplified F = ma. Putting
all that together gets us an equation for the force that the user applies to the platform as a function of time and the acceleration that it gives to the
platform as a function of time:
We can also calculate the power as a function of time by knowing that mechanical power is force multiplied by velocity.
Since we want to know the force as a function of time, we must figure out the acceleration as a function of time. And since we want to know the
power as a function of time, we must know the velocity as a function of time. Fortunately for us the acceleration is related to the velocity:
acceleration is the time rate of change of velocity. So if we know or can estimate the velocity as a function of time, then we can know the force and
power as a function of time. Instead of measuring the velocity vs. time, I will estimate it based on experience from doing the exercise. When doing
this exercise it is noticeable that the platform velocity increases to a peak just before the top. Then it slows quickly to a stop at the top. The force is
large and increasing at the start of the motion. Then it quickly drops to what feels like zero just before the top. Then it quickly rises again at the top ofthe travel. From those observations I believe the platforms velocity vs. time is close to a skewed parabola: a nice smooth velocity vs. time curve that
starts at zero going slowly up to a peak then going quickly back to zero. We can use that observation and the other facts we know to calculate an
estimate of the force vs. time and the power vs. time.
*This is the familiar F=maand the Greek
letter sigma,, means sum of the+
-
8/13/2019 Total Gym Pedestal
19/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 19
Calculating the Force and Power vs. Time from the PlatformsAcceleration and Velocity
0.0
10.0
20.0
30.040.0
50.0
60.0
70.0
0.0 0.1 0.2 0.3 0.4 0.5Velocity(inches/second)
Time (Seconds)
Velocity Along Rail vs Time
0.0
5.0
10.0
15.0
20.0
0.0 0.1 0.2 0.3 0.4 0.5Displacement(in
ches)
Time (Seconds)
Displacement Along Rail vs Time
-900.0-750.0-600.0-450.0-300.0-150.0
0.0150.0300.0
0.0 0.1 0.2 0.3 0.4 0.5Acceleration(inches/second^2)
Time (Seconds)
Acceleration Along Rail vs Time
Based on experience from doing the prone
push-down exercise this is an estimate of the
velocity vs. time: a skewed parabola.
v(t) = -3552t3+1776t
2
This displacement vs. time is the integral of the
velocity vs. time equation and it fits the known
fact of 18.5 travel in 0.5 seconds.
This acceleration vs. time is the derivative of the
velocity vs. time equation.a(t) = -10656t
2+3552t
-100.0-50.0
0.050.0
100.0150.0
200.0250.0300.0
0.0 0.1 0.2 0.3 0.4 0.5
Force(Lbs)
Time (Seconds)
Force Applied to Platform vs Time
0.0
0.5
1.0
1.5
2.0
0.0 0.1 0.2 0.3 0.4 0.5
Power(H.P.)
Time (Seconds)
Power Applied to Platform vs
Time
AverageTwo Arm Power
AverageOne Arm Power
The average one-arm
power is 0.4 HP
The peak force is 275 Lbs
which is 2.2x the static
force of 123 Lbs.
-
8/13/2019 Total Gym Pedestal
20/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 20
Power Required Per-Person in Tandem Marathon Canoe Paddling
How much power does it take to paddle a tandem marathon canoe? Suppose it takes an average, continuous force of 50 Lbs1to propel a canoe at 7
mph. 7 mph equals 10.3 ft/s. In linear motion, power is force x velocity so the average power is 50 Lbs x 10.3 ft/s = 515 ft-Lbs/s. Converting to Horse
Power, 515 ft-Lbs/s 550 ft-Lbs/s per H.P. = 0.9 H.P. per 2 people. So it requires about 0.5 H.P. per paddler to travel at 7 mph.
150 Lbs is very likely to be at the high end of the actual force required to overcome friction drag and wave drag in deep, calm water.
Comparison of Power: Example Prone Push-Down Exercise vs. 7 MPH Tandem Marathon Canoe Analysis of the example for the prone push-down exercise gave us a result of 0.4 H.P. as the average power from one arm.
Recall that the motion of the prone push-down exercise is very similar to the top hand motion of the canoe stroke.
Analysis of the example for paddling a tandem marathon canoe at 7 mph gave us a result of 0.5 H. P. required per paddler.Conclusion: The top hand in the canoe stroke is capable of producing a large portion of the power required from a paddler in a tandem canoe.
This simple analysis lends support to what many marathon canoe paddlers already know - effectively using the power of the top hand is
a critical ingredient to maximize the canoe speed.
Knowing that effective use of the top hands power is critical to maximizing the canoe speed leads to the question - What conditions
enable effective use of the top hands power?
1. The top hand must be directly above the blade for the entire duration of the power stroke.2. The blade must remain at a fixed distance (laterally) from the canoes keelfor the entire duration of the power stroke.3. The blade must be fully submerged and perpendicular to the canoes keel for the entire duration of the power stroke.
In practice it means When the catch* occurs, the top hand must already be directly over the blade and it must immediately begin
powering the canoe forward, continuing until the end of the power stroke.
* The catch is that moment at the end of the recovery phase when the blade is quickly and fully submerged. It is the start of the power
stroke.
Comment: This comparison makes the implicit assumption that the power expended in one rep. of the prone push-down exercise can be repeated
for each of the many, many strokes of paddling a canoe. That is not likely to be true. Perhaps1/3to
1/2of the calculated power could be
sustained. Also in calculating the power required to propel the canoe, the force used is likely at the high end of the actual requirement
which may be between 30 to 50 Lbs. Even considering these reductions, the conclusion stays the same.
-
8/13/2019 Total Gym Pedestal
21/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 21
Unintentional and Happy Consequences The seated, single arm lat pull downThe pedestal has made possible doing a seated, single arm lat pull down. It is easy to reach up and pull down on one of the handles while sitting on a
low seat opposite the Total Gyms platform. To replicate the top arms paddling motion just take your arm across your body and grab the handle then
press it straight down keeping your knuckles pointed forward. Holding onto a loop of rope that is around your foot will position your bottom hand
approximately at the start-of-stroke location. When the total gym was at its factory height the handles were a little too low and the base was not
wide enough to be stable during this exercise. To make this motion useful for training you should have additional weight added to the platform. One
way to do that is with the addition of a bar to the platform and barbell plates as shown earlier in this document. Here are a few photos that show thearrangement and motion. Notice that my right hand is pulling the handle down on my left side and outboard of my left leg.
-
8/13/2019 Total Gym Pedestal
22/23
-
8/13/2019 Total Gym Pedestal
23/23
A Pedestal Design for the Total Gym Revision C 2009 Richard Butts Page 23
Total Gym 1000 Series: Diagonal Support Attachment Height Total Gym 1000 Series: Platform Rail Length
top related