amplifier - car-hifi-pool.de · pdf fileclass ab ab ab d d 4 ohm stereo 2 x 80 watts rms 4 x...

AMPLIFIER

INTRODUCTIONThis instruction manual is for your safety and must be adhered to at all times. Please read and ensure that you fully understand the installation and set up procedures as explained. If you are unclear on the installation or set up of your EDGE speakers please contact your nearest authorised EDGE dealer.

WARNINGDO NOT EXPOSE THIS PRODUCT TO DAMP OR MOISTURE - doing so may result in fire,

shock or damage to the product.BEFORE WIRING DISCONNECT THE CABLE FROM THE POSITIVE BATTERY TERMINAL -

failure to do so may result in electric shock or injury.ENSURE GOOD AND CORRECT CONNECTIONS - failure to make the correct connections

may result in fire or damage to the product.DO NOT USE ANY FUNCTIONS OF THIS EQUIPMENT THAT MAY TAKE YOUR

CONCENTRATION AWAY FROM DRIVING YOUR VEHICLE - do not set up your amplifier whilst driving, doing so may result in an accident. For prolonged setting up, make sure that

your vehicle is stationary and in a safe location.KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE - failure to do this may result in an accident. EDGE equipment is capable of producing sound levels that can permanently damage your hearing. EDGE recommends caution when listening at high volume. For safe and enjoyable listening the sound should be comfortable and clear without distortion.

CAUTIONNever connect any speaker lead to the car chassis. This can cause severe damage to your

speaker /car radio /amplifier.Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.

Use caution when working near the fuel / hydraulic lines and electrical wiring.Observe the correct polarity when wiring, improper phasing may cause a loss of bass

response.Ensure that no moving parts catch on the speaker or grill (e.g. window or door handles, or

window glass inside the door)

Mounting Guidelines

Your EDGE amplifier is designed with a swift installation routine in mind. Please mount the amplifier in a dry location on a solid surface. NEVER mount the amplifier upside down, this will cause the amplifier to over heat and will eventually damage the amplifier. Before fixing the amplifier in place please ensure that there is sufficient air flow around the exterior of the casing, at least two inches is sufficient.

Connections

Power / Ground Cable● The correct gauge cable should be used for both the power and the ground connections to the amplifier. ● The power cable should be taken directly from the battery. Rubber grommets should be used when passing through any bulkheads to prevent the cable from becoming chaffed or cut. ● The correct size of fuse must be fitted within 18” of the battery and before the cable passes through the bulk head● It is vital that a fuse / circuit breaker (of at least equal value to the one fitted on the amplifier) is placed inline with the power cable and is no further than eighteen inches away from the battery. ● Please ensure that the fuse is not fitted until the entire installation procedure is complete. ● The two tables below are to help you decide on what cable is correct for you. The first enables you to select the size of cable depending on the length required. The second will help you convert the cable size from American Wire Gauge to Metric if you need to.● The amplifier ground should be connected directly to the chassis of the vehicle, to bare metal. ● The cable length should be kept to an absolute minimum.

Mo

de

l E

D2

04

E

D2

05

E

D2

06

E

D2

09

Ty

pe

Coa

xial

C

oaxi

al

Coa

xial

C

oaxi

al

Con

figur

atio

n 4

way

4

way

4

way

4

way

Spea

ker s

ize

4” (1

00m

m)

5.25

” (13

0mm

) 6.

5” (1

65m

m)

6x9”

(150

x 2

20m

m)

R

MS

pow

er

40 w

atts

50

wat

ts

60 w

atts

10

0 w

atts

Pe

ak p

ower

12

0 w

atts

15

0 w

atts

18

0 w

atts

30

0 w

atts

M

inim

um in

put

20 w

RM

S 25

wR

MS

30 w

RM

S 50

wR

MS

Sens

itivi

ty

83.9

dB

86.2

dB

86.2

dB

86.1

dB

Freq

uenc

y re

spon

se 1

00H

z –

20KH

z 80

Hz

– 20

KHz

65hz

– 2

0KH

z 45

Hz-

20K

Hz

Mou

ntin

g de

pth

43m

m

47m

m

55m

m

72m

m

Mou

ntin

g di

amet

er

94m

m

118m

m

144m

m

150x

220m

mR

ecom

men

ded

ED74

00/7

800

ED74

00/7

800

ED74

00/7

800

ED74

00/7

800

ampl

ifier

ED

7160

0 ED

7160

0 ED

7160

0

ED

7160

0

Mo

de

l E

D3

05

E

D3

06

Type

co

mpo

nent

co

mpo

nent

C

onfig

urat

ion

2 w

ay

2 w

ay

Sp

eake

r siz

e 5.

25” (

130m

m)

6.5”

(165

mm

)

R

MS

pow

er

70 w

atts

80

wat

ts

Pe

ak p

ower

21

0 w

atts

24

0 w

atts

M

inim

um in

put

35 w

atts

RM

S 40

wat

ts R

MS

Sens

itivi

ty

82.2

dB

84.4

dB

Fr

eque

ncy

resp

onse

80H

z –

20KH

z

65h

z –

20KH

z

M

ount

ing

dept

h

54m

m

57m

m

Mou

ntin

g di

amet

er

114m

m

144m

mR

ecom

men

ded

ED74

00/7

800

ED74

00/7

800

ampl

ifier

ED

7160

0 ED

7160

0

Mo

de

l E

D7

40

0

ED

78

00

E

D716

00

E

D712

00

E

D7

25

00

Ty

pe

2/1

chan

nel

4/3/

2 ch

anne

l 4/

3/2

chan

nel

Mon

oblo

ck

Mon

oblo

ck

C

lass

AB

AB

AB

D

D

4

ohm

ste

reo

2 x

80 w

atts

RM

S 4

x 80

wat

ts R

MS

4 x

140

wat

ts R

MS

N/A

N

/A

2 oh

m s

tere

o 2

x 10

0 w

atts

RM

S 4

x 10

0 w

atts

RM

S 4

x 20

0 w

atts

RM

S N

/A

N/A

4 oh

m m

ono

1 x

200

wat

ts R

MS

2 x

200

wat

ts R

MS

2 x

400

wat

ts R

MS

1 x

200

wat

ts R

MS

1 x

400

wat

ts R

MS

2 oh

m m

ono

N/A

N

/A

N/A

1

x 40

0 w

atts

RM

S 1

x 80

0 w

atts

RM

S1

ohm

mon

o N

/A

N/A

N

/A

1 x

600

wat

ts R

MS

1

x 12

50 w

atts

RM

SM

ax p

ower

40

0 w

atts

80

0 w

atts

16

00 w

atts

12

00 w

atts

25

00 w

atts

Freq

resp

onse

20

Hz

– 20

KHZ

20H

z –

20KH

z

20H

z –

20KH

z 20

Hz

– 30

0Hz

20 H

z –

300H

zH

eigh

t 66

mm

66

mm

66

mm

66

mm

66

mm

Wid

th

282m

m

332m

m

452m

m

332m

m

416

mm

Dep

th

245m

m

245m

m

245m

m

245m

m

245m

m

Mo

de

l E

D510

E

D512

E

D515

Type

su

bwoo

fer

subw

oofe

r su

bwoo

fer

Spea

ker s

ize

10” (

272m

m)

12” (

324m

m)

15” (

397m

m)

RM

S po

wer

25

0 w

atts

30

0 w

atts

35

0 w

atts

Pe

ak p

ower

75

0 w

atts

90

0 w

atts

10

50 w

atts

M

inim

um in

put

125

wat

ts R

MS

150

wat

ts R

MS

175

wat

ts R

MS

Se

nsiti

vity

89

dB

90dB

90

dB

Fr

eque

ncy

resp

onse

30

Hz

- 170

0Hz

25H

z –

1500

KHz

20hz

– 8

50H

z

Mou

ntin

g di

amet

er

235m

m

285m

m

350m

m

Mou

ntin

g de

pth

125m

m

144m

m

148m

m

Vo

ice

coil

2 oh

m D

VC

2 oh

m D

VC

2 oh

m D

VCR

ecom

men

ded

ED71

200/

7250

0 ED

7120

0/72

500

ED71

200/

7250

0

ampl

ifier

ED74

00/7

800/

7160

0 ED

7400

/780

0/71

600

ED74

00/7

800/

7160

0

Mo

de

l E

DB

10

E

DB

12

E

DB

12

T

EB

615

D

river

ED

510

ED51

2 2

x ED

512

ED51

5

En

clos

ure

impe

danc

e 1

or 4

Ohm

1

or 4

Ohm

1,

4 o

r 8 O

hm

1 or

4 O

hm

R

MS

pow

er

250

wat

ts

300

wat

ts

600

wat

ts

350

wat

ts

Peak

pow

er

750

wat

ts

900

wat

ts

1800

wat

ts

1050

wat

ts

Rec

omm

ende

d

ED

7120

0/72

500/

ED

7120

0/72

500/

ED

7120

0/72

500/

ED

7120

0/72

500/

ampl

ifier

ED

7400

/780

0/71

600

ED74

00/7

800/

7160

0 ED

7400

/780

0/71

600

ED74

00/7

800/

7160

0

Mo

de

l E

D p

ack 1

0

ED

pa

ck 1

2

ED

pa

ck 1

2 t

win

encl

osur

e ED

610

ED61

2 ED

612T

ampl

ifier

ED

7400

ED

7400

ED

7120

0

Spea

ker s

ize

10” (

272m

m)

12” (

324m

m)

15” (

397m

m)

RM

S po

wer

25

0 w

atts

30

0 w

atts

60

0 w

atts

Pe

ak p

ower

75

0 w

atts

90

0 w

atts

18

00 w

atts

Am

plifi

er w

iring

kit

10AW

G in

clud

ed

10AW

G in

clud

ed

8AW

G in

clud

e d

Mo

de

l E

D4

02

E

D4

04

E

D4

05

E

D4

06

E

D4

08

Ty

pe

bulle

t tw

eete

r b

ulle

t tw

eete

r M

idra

nge

Mid

rang

e m

idra

nge

C

onfig

urat

ion

1 w

ay

1 w

ay

1 w

ay

1 w

ay

1 w

ay

Sp

eake

r siz

e 2”

(50m

m)

4” (1

00m

m)

5.25

” (13

0mm

) 6.

5” (1

65m

m)

8” (2

00m

m)

RM

S po

wer

40

wat

ts

50 w

atts

80

wat

ts

300

wat

ts

450

wat

ts

Peak

pow

er

120

wat

ts

150

wat

ts

240

wat

ts

100

wat

ts

150

wat

ts

Min

imum

inpu

t 20

wat

ts R

MS

25 w

atts

RM

S 40

wat

ts R

MS

50 w

atts

RM

S 75

wat

ts R

MS

Se

nsiti

vity

10

6dB

107d

B 96

dB

97dB

98

dB

Freq

uenc

y re

spon

se 5

KHz

– 20

KHz

4.5K

HZ

– 20

KHz

80H

z –

6KH

z 65

hz –

6KH

z 55

Hz

– 6K

Hz

M

ount

ing

diam

eter

43

mm

90

mm

11

4mm

14

6mm

18

3mm

M

ount

ing

dept

h 40

mm

70

mm

49

mm

55

mm

82

mm

R

ecom

men

ded

ED74

00/7

800/

ED

7400

/780

0/

ED74

00/7

800/

ED

7400

/780

0/

ED74

00/7

800/

am

plifi

er

ED71

600

ED71

600

ED71

600

ED71

600

ED71

600

M

od

el

ED

710

E

D712

E

D715

E

D718

Type

w

oofe

r w

oofe

r w

oofe

r w

oofe

r

Sp

eake

r siz

e 10

” (27

2mm

) 12

” (32

4mm

) 15

” (39

7mm

) 18

” (45

7mm

)

RM

S po

wer

40

0 w

atts

50

0 w

atts

60

0 w

atts

90

0 w

atts

Pe

ak p

ower

12

00 w

atts

15

00 w

atts

18

00 w

atts

27

00 w

atts

Min

imum

inpu

t 20

0 w

atts

RM

S 15

0 w

atts

RM

S 30

0 w

atts

RM

S 45

0 w

atts

Sens

itivi

ty

97dB

98

dB

99dB

02

dB

Fr

eque

ncy

resp

onse

30H

z –

5.5K

Hz

25H

z –

5.5K

Hz

20hz

– 5

KHz

15H

z –

5KH

z M

ount

ing

diam

eter

23

4mm

28

4mm

35

2mm

42

8mm

Mou

ntin

g de

pth

113m

m

130m

m

128m

m

186m

m

Vo

ice

coil

2 oh

m D

VC

2 oh

m D

VC

2 oh

m D

VC

2 oh

m D

VCR

ecom

men

ded

ED71

200/

ED72

500

ED71

200/

7250

0 ED

7120

0/72

500

ED71

200/

7250

0

ampl

ifier

ED

7400

/780

0/71

600

ED71

600

ED71

600

ED72

500

Limited WarrantyAll EDGE goods are covered by a full 12 months manufacturers warranty. Valid from the date of the original receipt and proof of purchase. In order to validate this warranty, the warranty card should be returned to EDGE within seven days of the original purchase date. The original receipt and packaging

should also be kept for this 12 month period.

If at any stage during the warranty period you have a problem with the product then it should be returned to the point of purchase in its original packaging,

complete and with no items missing.

If the store is unable to fix the product it may have to be returned to EDGE this process takes around 7

working days.

A full description of EDGE’s warranty information can be found on our website:

www.edgecaraudio.com/warranty

A written version can also be obtained from EDGE warranty department

PO Box 11000B75 7WG

Copyright All content included in this manual such as text, graphics, logos, icons, images data, the selection and arrangement thereof, are the property of EDGE Audio (herein referred

to as “EDGE”, “us” or “we”) and its affiliate or their content and technology providers, and are protected by United Kingdom and International copyright laws. All

rights reserved.

Trademarks EDGE ED2TM, EDGE ED3TM , EDGE ED4TM , EDGE ED5TM

EDGE ED6TM , EDGE ED7TM, EDGE StreetTM and EDGE LoudTM and all stylised representations of

product names, or the abbreviations of product names, as logos are all trademarks of EDGE. Graphics and

logos are trademarks or trade dress of EDGE Audio or its subsidiaries.

EDGE’s trademarks and trade dress may not be used in connection with any product or service that is not EDGE’s,

in any manner that is likely to cause confusion among customers or in any manner that disparages or discredits EDGE. All other trademarks not owned by EDGE or its subsidiaries that appear in this manual are the property

of their respective owners, who may or may not be affiliated with, connected to, or sponsored by EDGE or

its subsidiaries. We reserve the right to make needed changes or

improvements to the produc and this manual , without informing the customer about this in advance

ED7400● Minimum 10 AWG power / ground cable should be used

ED7800 / 71200 / 71600● Minimum 8 AWG power / ground cable should be used

ED72500● Minimum 4 AWG power / ground cable should be used

Remote Turn On

● A minimum of 18 gauge cable should be used for this connection. ● The cable should be run with exactly the same care and attention as the power cable and taken back to the source (headunit) and joined to the remote cable provided. ● If the source (headunit) does not have a remote turn on cable then a 12v supply should be used. This will require a switch to be fitted inline to enable the amplifier to be turned on and off. Remember that if this switch is left on you will flatten the car battery.

RCA Cables

● Depending on the model number of your amplifier and the number of speakers you wish to power you will have to run either one or two RCA cables from the source to the amplifier. ● Please take extra care when running these cables from the source to the amplifier. Ensure that they are placed away from all items that can generate any interference, wiring harnesses etc. ● It is recommended that the RCA cables should be run on opposite sides of the car to the previously installed power cables if possible, to avoid the cable picking up interference.

Terminals and Controls ED7400

5. Low Pass Crossover ControlThe control is used to select the low pass filter frequency. The frequency ranges are from 45 Hz to 300 Hz.

6. Crossover Control SwitchThis switch is used to select high pass, low pass or flat (no crossover) operation for the amplifier speaker outputs.

7. High Pass Crossover ControlThe control is used to select the High pass filter frequency. The frequency ranges are from 45 Hz to 300Hz.

8. Bass Boost Remote Input JackUse to plug in the remote bass controller. (Optional ) see back

9. High Level InputTo be used when no RCA’s are available. Use the provided loom to connect to closest speakers. The loom connector will only fit one way around. Once plugged in you should connect the wires as below:

Left Positive - White Right Positive - Grey Left Negative - White / Black Right Negative - Grey / Black

10. Indicator LEDWhen the amplifier is operating correctly the LED will show as green. When the amplifier is in protection mode the LED will show as red.

11. Power ConnectionsPower connections. See Connections section for details on correct connections.

12. FusesPlease ensure the following fuse rating is used when replacing fuses: 15 amp x 2

13. Speaker Terminal OutputFor connection to the speakers. See Application section for wiring examples.

P o w e r P r o t e c t

S P - S P - S P + S P +

R

I n p u t

L + R + L - R -

R

L L

H i L e v e l L i n e O u t L i n e I n

O F F O N

S u b s o n i c P h a s e L P F G a i n

M i n M a x 3 5 H z 2 5 0 H z 0 ° 1 8 0 ° 8 0 H z 1 6 H z 2 4 d B 0 d B

R e m o t e B a s s B o o s t

ED72500 ED71200

ED71200

ED7800

ED7800

ED72500

MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS

ED71600

ED71600

4 CHANNEL AMPLIFIER 4 X 200 WATTS RMS

ED7400

ED7400 2 CHANNEL AMPLIFIER 2 X 100 WATTS RMS



4 x 35 AMP

3 x 35 AMP

INPUT

2 x 15 AMP

2 x 25 AMP

2 x 20 AMP

1 2 57 83 46910

11 12 13

123 5 7 8649

1011 12

12 3 4 95

6 714

8 10

11 12 13

11 2 3 4 5 6 89

10 11 1213

7234 5 67 89

10 1112

13 14

1. Low Level OutputA daisy chain output For connection to another amplifier with a low level input using only a single RCA output from the source (headunit).

2. Low Level InputFor connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit)

3. Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.

4. Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.

1. Low Level InputFor connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit).

2. Rear Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.

3. Rear Crossover ControlThe switch is used to select between low pass / high pass filter or no filter at all on the front channels. The frequency ranges on the low pass filter are from 40 Hz to 300 Hz. The frequency ranges on the high pass filter are from 40 Hz to 300hz.

4. Rear Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.

5. Front Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.

6. Front Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.

7. Front Crossover ControlThe switch is used to select between low pass / high pass filter or no filter at all on the rear channels. The frequency ranges on the low pass filter are from 40 Hz to 300 Hz. The frequency ranges on the high pass filter are from 40 Hz to 300hz.

8. Front Bass Boost Remote Input JackUse to plug in the remote bass controller. (optional)

9. Indicator LEDWhen the amplifier is operating correctly the LED will show as green When the amplifier is in protection mode the LED will show as red.




.



S P - S P - S P + S P +

R

I n p u t

L + R + L - R -

R

L L


O F F O N




ED72500 ED71200

ED71200

ED7800

ED7800

ED72500


ED71600

ED71600


ED7400




4 x 35 AMP

3 x 35 AMP

INPUT

2 x 15 AMP

2 x 25 AMP

2 x 20 AMP

1 2 57 83 46910

11 12 13

123 5 7 8649

1011 12

12 3 4 95

6 714

8 10

11 12 13

11 2 3 4 5 6 89

10 11 1213

7234 5 67 89

10 1112

13 14

1. Low Level InputFor connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit).


Front Speakers

Left Positive - Green Right Positive - PurpleLeft Negative - Green / Black Right Negative - Purple / Black

Rear Speakers

Left Positive - White Right Positive - GreyLeft Negative - White / Black Left Negative - Grey / Black

3. Front Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.

4. Front Crossover ControlThe switch is used to select between low pass / high pass filter or no filter at all on the front channels. The frequency ranges on the low pass filter are from 45 Hz to 300 Hz. The frequency ranges on the high pass filter are from 45 Hz to 300 Hz.

5. Front Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.

6. Rear Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.

7. Rear Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.

8. Rear Crossover Control SwitchThe switch is used to select between low pass / high pass filter or no filter at all on the rear channels. The frequency ranges on the low pass filter are from 45 Hz to 300 Hz. The frequency ranges on the high pass filter are from 45 Hz to 300 Hz.

9. Front Bass Boost Remote Input JackUse to plug in the remote bass controller. (optional)

10. Indicator LEDWhen the amplifier is operating correctly the LED will show as green. When the amplifier is in protection mode the LED will show as red.




14. Input Mode Select SwitchAllows 4 channels to be driven from a single pair of RCA leads



S P - S P - S P + S P +

R

I n p u t

L + R + L - R -

R

L L


O F F O N




ED72500 ED71200

ED71200

ED7800

ED7800

ED72500


ED71600

ED71600


ED7400




4 x 35 AMP

3 x 35 AMP

INPUT

2 x 15 AMP

2 x 25 AMP

2 x 20 AMP

1 2 57 83 46910

11 12 13

123 5 7 8649

1011 12

12 3 4 95

6 714

8 10

11 12 13

11 2 3 4 5 6 89

10 11 1213

7234 5 67 89

10 1112

13 14

1. Low Level InputFor connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit).


Left Positive - Brown Right Positive - Black Left Negative - Blue Right Negative - Green


4. Low Pass Filter ControlLow pass frequency control. The frequency ranges from 35 Hz to 250 Hz.

5. Phase ControlCan be used to alter the phase of the subwoofer from 0 - 180 degrees.IE: the speaker output can be In phase or out of phase with the other speakers in the vehicle. For best results rotate the dial between the two settings to determine the best sound.

6. Subsonic Filter ControlThis is used to filter out unwanted amplifier output to the subwoofer. Effectively this will filter out all the frequencies up to the crossover point set with the control. The range is from 16 Hz to 80 Hz.Frequencies of 80 Hz and below cause the subwoofer to work hard, some subwoofers can easily be damaged when playing very low frequencies. Using the subsonic filter allows less distortion, delivers frequencies better suited to the subwoofer prolonging its life.

7. Subsonic Filter SwitchUsed to turn the filter on or off.

8. Bass Boost SwitchTo provide up to an extra +18 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.

9. Bass Remote Input JackUse to plug in the remote bass controller. 10. Indicator LEDWhen the amplifier is operating correctly the LED will show as greeb. When the amplifier is in protection mode the LED will show as red.

11. FusesPlease ensure the following fuse rating is used when replacing fuses:20 amp x 2



14. Low Level OutputDaisy chain RCA connection to allow easy addition of another amplifier.



S P - S P - S P + S P +

R

I n p u t

L + R + L - R -

R

L L


O F F O N




ED72500 ED71200

ED71200

ED7800

ED7800

ED72500


ED71600

ED71600


ED7400




4 x 35 AMP

3 x 35 AMP

INPUT

2 x 15 AMP

2 x 25 AMP

2 x 20 AMP

1 2 57 83 46910

11 12 13

123 5 7 8649

1011 12

12 3 4 95

6 714

8 10

11 12 13

11 2 3 4 5 6 89

10 11 1213

7234 5 67 89

10 1112

13 14

1. Low Level Input

For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit).


3. Low Pass Filter ControlLow pass frequency control. The frequency ranges from 40 Hz to 250 Hz.

4. Phase ControlCan be used to alter the phase of the subwoofer from 0 - 180 degrees.IE: the speaker output can be Inphase or out of phase with the other speakers in the vehicle. For best results flick between the two settings to determine the best results.

5. Subsonic Filter ControlThis is used to filter out unwanted amplifier output to the subwoofer. Effectively this will filter out all the frequencies up to the crossover point set with the control. The range is from 15 Hz to

50 Hz.Frequencies of 80 Hz and below cause the subwoofer to work hard, some subwoofers cane easily be damaged when playing very low frequencies. Using the subsonic filter allows less distortion, delivers frequencies better suited to the subwoofer prolonging its life.

6. Subsonic Filter SwitchUsed to turn the filter on or off.

7. Bass Boost control To provide up to an extra +18 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.

8. Bass Remote Input JackUse to plug in the remote bass controller. 9. Indicator LEDWhen the amplifier is operating correctly the LED will show as green. When the amplifier is in protection mode the LED will show as red.

10. FusesPlease ensure the following fuse rating is used when replacing fuses:35 amp x 4



13. Low Level OutputDaisy chain RCA connection to allow easy addition of another amplifier.


S P - S P - S P + S P +

R

I n p u t

L + R + L - R -

R

L L


O F F O N




ED72500 ED71200

ED71200

ED7800

ED7800

ED72500


ED71600

ED71600


ED7400




4 x 35 AMP

3 x 35 AMP

INPUT

2 x 15 AMP

2 x 25 AMP

2 x 20 AMP

1 2 57 83 46910

11 12 13

123 5 7 8649

1011 12

12 3 4 95

6 714

8 10

11 12 13

11 2 3 4 5 6 89

10 11 1213

7234 5 67 89

10 1112

13 14


Troubleshooting

● Before removing the amplifier, refer to the list below and follow the suggested procedures. ● Always test the speakers and confirm that they are wired correctly first. ● If in any doubt get help from a qualified auto electrician.

Amplifier Will Not Power Up● Check for good ground connections. Ensure Ground cable is connected directly to bare metal and not a painted surface. ● Using a multimeter check that remote terminal has at least 10V DC.● Using a multi meter check that there is battery voltage on the positive terminal.● Check all fuses.● Check that the protection light is not illuminated. If it is lit, shut off the amplifier for thirty seconds and then turn it back on.

Protection LED Illuminates When Amplifier Is Powered Up● Check for shorts on all speakers wires. (IE no speaker wires should be joined together and no speaker wires should be touching the cars chassis)● The amplifier is designed to shut down automatically when the units temperature goes above 80 degrees. If the amplifier feels very hot then this may be the reason for the amplifier not starting.● Remove the speaker wires and reset the amplifier. If the protection LED still comes on then the amplifier is faulty. This damage may have been caused by either failure to follow these setup guidelines or abuse.

Amplifier Gets Very Hot● Check the minimum speaker impedance for the amplifier is correct. ● Check for shorts on all speakers wires. (IE no speaker wires should be joined together and no speaker wires should be touching the cars chassis)● Check that there is good airflow around the amplifier. In some applications an external fan may be required.

Blown Fuse(s) ● Check both positive supply and ground for shorts.● Check that the positive wire is connected to the positive terminal on the amplifier.● Check that the negative wire is connected to the ground terminal on the amplifier. ● Ensure that the correct rated fuse is fitted

Distorted Sound● Check the gain control is not set at too high a level. If the speakers sound distorted turn the down the gain until the sound is clear. ● Check that all crossover frequencies are correct. See setup section for more details. ● Check for shorts on all speaker wires. ● Check all speakers are wired correctly. With the correct polarity being observed on each connection.

Set Up Section

To correctly set the gain control of the amplifier to match that of the source (headunit) use the following setup routine:

Turn the gain control to minimum on the amplifier.Ensure the bass boost is set to 0 dB.On the headunit set all crossovers to flat and both bass and treble to zero.Turn up the source (headunit) to approx 3/4 volume.Very slowly turn up the gain on the amplifier until distortion can be heard in any of the speakers or until the volume reaches an uncomfortable listening level when this is reached turn down the gain control slightly.

The gain control is now set.

The setting of the crossover will depend on what kind of speaker you are installing.

For a subwoofer it is recommended that the crossover is set to Low Pass and the frequency is set to match that of the speakers specifications.

For a pair of full range speakers it is recommend that the crossover is set to Flat. The two frequency controls will then have no effect on the amplifiers output and the speaker will receive a full range signal. However, using the high pass crossovers will allow more control of your speakers. By removing the bass (low frequencies) the speakers can perform at higher volumes with less distortion.

Note: The smaller the speaker, the less bass it can handle. Adjust the crossover to get the most and best sound from your speakers. The easiest was to do this is by limiting the amount of bass you feed them

For a pair of speakers with a passive crossover it is recommended that the crossover is set to High Pass and the frequency is set to match that of the speakers specifications.

Note:

By using the crossovers correctly you will not only lengthen the life of your speakers but you will also get better performance from them. To optimise your setup seek the advice of a professional installation engineer or visit your local EDGE audio dealer.

PowerProtect

SP- SP- SP+SP+

ED71200

ED7800



2 x 25 AMP

2 x 20 AMP

ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS

2 x 15 AMP


2 x 15 AMP


2 x 25 AMP

PowerProtect

SP- SP- SP+SP+

ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS

2 x 20 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

+ - + -

+ -

+ -

+ - + -

+ - + -

+ - + -

+-

+-+-

+-

+- +-

+-

PowerProtect

SP- SP- SP+SP+

ED71200

ED7800



2 x 25 AMP

2 x 20 AMP


2 x 15 AMP


2 x 15 AMP


2 x 25 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

+ - + -

+ -

+ -

+ - + -

+ - + -

+ - + -

+-

+-+-

+-

+- +-

+-

ED7400 in 2 channel configuration connected to a pair of ED209 speakers

ED7400 in bridged configuration connected to an ED512 subwoofer

Minimum impedance 2 Ohms


ED7800 / 71600 in 4 channel configuration connected to 2 pairs of ED209 speakers

ED7800 / 71600 in 3 channel configuration connected to a pair of ED209 speakers and an ED512 subwoofer





Applications

PowerProtect

SP- SP- SP+SP+

ED71200

ED7800



2 x 25 AMP

2 x 20 AMP


2 x 15 AMP


2 x 15 AMP


2 x 25 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

+ - + -

+ -

+ -

+ - + -

+ - + -

+ - + -

+-

+-+-

+-

+- +-

+-

PowerProtect

SP- SP- SP+SP+

ED71200

ED7800



2 x 25 AMP

2 x 20 AMP


2 x 15 AMP


2 x 15 AMP


2 x 25 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

+ - + -

+ -

+ -

+ - + -

+ - + -

+ - + -

+-

+-+-

+-

+- +-

+-

ED71200 connected in mono configuration to an ED512 subwoofer at 4 ohms


ED71200 connected in mono configuration a pair of ED512 subwoofers at 2 ohms

Minimum Impedance 1 Ohms

ED71200 connected in mono configuration to 4 ED512 subwoofers at 1 ohms


PowerProtect

SP- SP- SP+SP+

ED71200

ED7800



2 x 25 AMP

2 x 20 AMP


2 x 15 AMP


2 x 15 AMP


2 x 25 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

PowerProtect

SP- SP- SP+SP+


2 x 20 AMP

+ - + -

+ -

+ -

+ - + -

+ - + -

+ - + -

+-

+-+-

+-

+- +-

+-


4 x 35 AMP


4 x 35 AMP


4 x 35 AMP

+ -

+ -+ -

+ -

+ - + -

+ -

ED72500connected in mono configuration to an

ED512 subwoofer at 4 ohms


ED72500connected in mono

configuration a pair of ED512

subwoofers at 2 ohms


ED72500connected in mono

configuration to 4 ED512 subwoofers

at 1 ohms


amplifier - car-hifi-pool.de · pdf fileclass ab ab ab d d 4 ohm stereo 2 x 80 watts rms 4 x...

Documents