amsj 8-17 buyer's guide · blue thunder solvent, bumblin bear grease, leather possible bags,...
TRANSCRIPT
AMERICAN SHOOTING JOURNAL’S 2017
GUNS/PARTS • ACCESSORIES • TARGETS AMMO • GUN CLEANING • OPTICS CONCEALMENT & MORE
BUYER’S GUIDE
BUYER’S
GUID
E
The Stealth Recoil Spring™ SRS™ is a self-contained multi-stage drop-in replacement for your standard buffer and spring.
S T E A LT H ™ R E C O I L SPR ING $79.00
www.armaspec.com
The Stealth Recoil Spring™ is designed to reduce felt recoil as well as keep the buffer spring from rubbing against the inner wall of the buffer tube. The buffer mass is designed to stay under constant tension against the bolt carrier and the O-ring on the head of the buffer mass prevents metal on metal contact. Pat. Pend.
SRS-Carbine at about 3.3oz equivalent, SRS-H at around 3.8oz equivalent, SRS-H2 at around 4.7oz equivalent, SRS-9 at around 5.6oz equivalent, SRS-H3 at around 5.6oz equivalent, and SRS-308 5.7oz.
The Stealth Recoil Spring comes in 6 variations.
4 American Shooting Journal // Buyer’s Guide 2017
AMMO/RELOADING
BLACK HILLS (See ad page 48)
In 2016, Black Hills Ammunition changed the rules for defensive
ammunition in .380 and .38 Special by introducing a new
concept: nonexpanding pistol bullets with hard-cutting edges
and deep flutes that outperform the best defensive hollow point
ammunition. These new bullets, developed in concert with
Lehigh Defense, literally and efficiently cut through barriers that
plug conventional hollowpoints, while creating larger, deeper
wound paths.
This year, Black Hills has added three more loads: the all-
new HoneyBadger 9mm 125 grain, and .45 ACP 135 grain for
the ultimate in self-defense, plus a HoneyBadger .44 Magnum
160 grain for hunting or defense against four-legged predators.
The HoneyBadger 9mm and .45 ACP were designed to provide
optimum performance in ballistic gelatin while avoiding over-
penetration. For more information, visit black-hills.com.
G2 RESEARCH (See ad page 2)
G2 Research R.I.P. 12 Gauge Slug:
WARNING: KEEP OUT OF REACH OF CHILDREN. To avoid serious
injury; (1) Use in smoothbore only; not for use with choke. (2)
Use only ammunition in good condition; (3) Use only in modern
firearms in good condition, proof tested in accordance with
industry standards and marked for use of this gauge and length
shot shell; (4) Ensure barrel is free from obstructions; check
barrel in case of unusually light recoil or an unusually loud or
weak sound during firing; (5) Wear eye and ear protection; (6) If
gun fails to fire, avoid exposure to breech when unloading, and
point muzzle in a safe direction. Keep firearm pointed in a safe
direction at all times; (7) Discharge may occur if primer is struck;
handle with caution, DO NOT DROP; (8) Do not use these shells
in guns with Damascus, twist steel, rifled or choked barrels;
(9) Do not shoot at hard surfaces or water to prevent ricochet;
(10) Store in a cool dry place away from chemicals that contain
ammonia; do not submerge in water. For more information,
visit g2rammo.com.
MATT’S BULLETS (See ad page 9)
Matt’s Bullets makes a large variety of bullets for reloading,
as well as cartridges that are ready to shoot. There are over a
hundred different bullets including very light to very heavy in an
assortment of calibers, with and without gas checks. Matt’s sells
mostly pistol bullets, but also has a variety of rifle bullets. They
have a very well-deserved reputation for quality.
They also sell a variety of .500 S&W cartridges including
some very unique items. One is a .500 S&W shot shell, which
is as powerful as a 28-gauge shotgun. They also make the
Tyrannosaurus Rex, which is a 700-grain bullet for the .500 S&W.
These are available both as bullets for reloading and also ready-
to-shoot complete cartridges. There are huge hollowpoints, spire
pointed bullets and many more.
They also make bullets and ammunition that are correct for
the Webley and Victory model revolvers. They have taken the
original British drawings and recreated a bullet which shoots to
point of aim and which is of the correct .361 diameter.
For more information, visit mattsbullets.com.
BUYER’S
GUID
E
BUYER’S
GUID
E
5.56
MM
C
OMING SOON...UNLOADED CASES AVAILABLE FROM SHELL SHOCK TECHNOLOGIES. 9MM CASES AVAILABLE NOW, OTHER CALIBERS COMING SOON. SEE WEBSITE FOR MANUFACTURERS OF LOADED AMMO
REVOLUTIONARY NEW 2-PIECE NAS3 CASE TECHNOLOGY: 50% LIGHTER THAN BRASS
Nickel-Plated Aluminum Base• Less wear on ejector pin• Can be color coded for ID/branding
High Tensile Nickel-Alloy Cylinder
WWW.SHELLSHOCKTECH.COM
• 2 x pressure rating (over 70k PSI)• Higher tensile strength and elasticity• Corrosion resistant• Reloadable using S3 Reload dies
UNUNLOLOSHSHOCOCAVAVAIAICOCOMMFOFOR R LOLOADAD
fofor r IDID/b/brarandndiningg
WWWWWWWW..SSHHEELLLLSSHHOOCC
6 American Shooting Journal // Buyer’s Guide 2017
OCTOBER COUNTRY (See ad page 7)
October Country Muzzleloading is currently celebrating 40
years of business. The company started with a hunting bag
made back in 1977. Today in North Idaho, OCM manufactures
a full line of brass accessories, ramrods, Pushing Daisy patches,
Blue Thunder solvent, Bumblin Bear grease, leather possible
bags, powder horns, primitive hand-forged products and many
other items for the muzzleloading industry. OCM products
also include something for Cowboy Action and black powder
cartridge shooters. As a manufacturer, they provide products to
the public at retail prices and to dealers at a wholesale price. For
more information, visit octobercountry.com.
RAINIER BALLISTICS (See ad page 9)
Introducing “The Wedge,” the first dedicated subsonic
expanding .300 Blackout bullet.
The .300 Blackout bullet has become an overnight
success caliber for the AR-15 platform. This 180-grain bullet
is designed specifically to work with low chamber pressures
and low velocity. Donny Shride, owner of Rainier Ballistics
LLC, developed it in conjunction with Alexander Arms. There
was a big motivation to develop this as there wasn’t a reliable
subsonic bullet for the .300 Blackout. More often than not, the
average .30-caliber bullet will not function consistently using
the .300 Blackout platform. The Wedge is important because it
is the first subsonic bullet designed from the ground up for the
.300 Blackout platform.
Here are just a few reasons this bullet is so appealing for both law
enforcement and civilians: First, you can run it through a suppressor.
And, since it is subsonic, it doesn’t have the velocity to penetrate
walls and cause collateral damage. You can use it in an indoor range.
And it is economical to load and expands at low velocities.
These reasons and more make the Wedge a great option for
people willing to load their own ammo for approximately half
the price of factory bullets, while also tailoring loads precisely to
their rifles. For more information, visit rainierballistics.com.
RIM ROCK (See ad page 9)
Rim Rock Bullets’
new gas-checked
.309 125-grain RNFP
bullet was designed
with the .30-caliber
carbine in mind. This
accurate bullet is good
in any .30-caliber
cartridge kept under
2,600 feet per second.
It’s also available in larger sizes, .310 to .312, and sold per
hundred in a plastic ammo box. For more information, visit
rimrockbullets.com.
SHARP SHOOTER RIMFIRE (See ad page 7)
Like most people, you
may not have even
realized it was possible
to reload .22 Long Rifle
ammo. But it is not
only possible, it is also
convenient with one
powerful tool and a
few accessories.
The Sharp Shooter
Rimfire manual contains
close-up photography,
cutaway views, and
all details necessary
to reload without any
other means.
If you are
concerned with .22
LR ammo shortages and tired of looking for bullets to go
plinking, their kit will help you become self-sufficient and
enjoy shooting on your own terms. This kit is a must have
if you are serious about your bug-out bag list and survival
gear. With the included instruction pamphlet, you will be
reloading .22 LR ammo using available resources while
others are left empty-handed.
BUYER’S
GUID
E
y
americanshootingjournal.com 7
BUYER’S
GUID
E
22LR
RELO
ADER
.COM
ALL THE TOOLS YOU NEED TO RELOAD 22LR OR 22 MAG
970-640-2799
Use coupon code SS1 on any order over $49 and get a FREE PACKAGE of PRIME-ALL ($20 value)
8 American Shooting Journal // Buyer’s Guide 2017
Whether you are preparing an adequate bug-out bag with
your survival gear or simply want to reload your own .22 Long Rifle
ammo, the Sharpshooter 22LR Reloader Kit is your answer. For
more information, visit 22lrreloader.com or call (970) 640-2799.
SHELL SHOCK TECHNOLOGIES (See ad page 5)
Shell Shock is focused on developing innovative case
technologies for the ammunition industry. Shell Shock is a
component manufacturer supplying its lightweight NAS3
cartridge cases to the shooting sports market, as well as to US
and foreign ammunition manufacturers. Shell Shock does not
load ammunition.
Shell Shock’s NAS3 cases are approximately 50 percent lighter
than brass, give more consistent round-to-round performance,
and can be picked up with a magnet. Shell Shock’s NAS3 case
technology can be applied to all small to midcaliber ammunition.
Nine millimeter Luger cases are immediately available, with
other popular pistol and rifle calibers coming soon.
Shell Shock has attracted several respected industry figures
to its board of directors, including:
• Jeff Hoffman, co-owner/founder and president of Black
Hills Ammunition. Black Hills is one of the highest-quality
ammunition manufacturers in the US and currently sells to all
branches of the US Military.
• Richard Abramson, founder and general manager of The
Centennial Gun Club. Richard also serves as chairman of the
Sporting Industry P20 Performance Group and on various boards
including the AcuSport Advisory Board, NSSF Retail Advisory
Council, Range Growth Advisory Board, and the Colorado
Firearm Safety Coalition.
All Shell Shock cases are designed and manufactured in the
US. For more information, visit shellshocktech.com or email
UNIQUETEK, INC. (See ad page 9)
UniqueTek is a company specializing
in unique and hard-
to-find products that
are useful for reloaders,
marksmen, and shooters
in general. The company’s
philosophy is that customers
appreciate a personal touch,
either by phone or email, and
are looking for a good value
for the products they buy.
The company has designed,
evaluated, and offers many
enhancements that make reloaded
ammunition more consistent, round
to round; items that make time at the
range more enjoyable, e.g. portable
target stands and the Brass Wizard for
picking up your brass; as well as premium
cleaners and lubricants to keep your firearms
operating smoothly. It’s not just unique, it’s UniqueTek! For more
information, visit uniquetek.com.
ZERO BULLETS (See ad page 7)
Reliability, accuracy and affordability – three reasons that Zero
is one of America’s fastest-growing bullet and ammunition
manufacturers. The Zero philosophy of growth is one of
patient testing, constant design research and rigid quality
control. For more than 50 years, Zero has maintained a level of
quality unsurpassed in the industry and, as new products are
introduced, our customers can be assured that each will be as
reliable, accurate, and affordable as our other proven designs.
Zero bullets are available in a wide variety of handgun
calibers and designs, from roundnose to wads, jacketed and
unjacketed. Zero’s new ammunition is packaged in our new
bright-red box, while reloads come in the familiar gold box, our
BUYER’S
GUID
E
cializing
d
d,
oaded
round
e at thhe
rtable
izard for
as premium
fi
americanshootingjournal.com 9
BUYER’S
GUID
E
Matt’s BulletsMatt’s Bullets
870-856-6788870-856-6788
www.mattsbullets.com/ammunitionwww.mattsbullets.com/ammunition
Premium Ammunition
Now Available:
500 S&W ShotshellsThe Power and payload of a 28 gauge shotshell in a revolver!
Also: 38/200 For Webley & Victory Revolvers
104 Turkey Pen Road • Highland, AR 72542
Matt s BulletsPremium AmmunitionPremium Ammunition
Specializing In 500 S&W Including:
500 S&W 700 Grain
Tyrannosaurus Rex
5T
38/2
855-507-0866 • 540 W. Iron Ave., Suite 118 • Mesa, AZ 85210
www.uniquetek.com • [email protected]
1
10 1112
13
14 15
16
17 18 19
7
6
8
9
5432
Enhancements for Dillon Precision Reloading Presses1. 2X Powder
Hopper Tube2. Micrometer Kit3. Toolhead
Clamp Kit4. Live Primer
Chute5. XL 650
Cartridge Chute Extension
6. Precision
7. Spent Primer Chutes
8. Turbo Bearing9. Dillon Die
Wrench10. SOLO ™
Single-Stage Conversion
11. CNC Toolheads12. The Bullet Bin13. Bin-Dam ™
14. Powder Measure Stand Adapter
15. Drain-n-Change Tool
16. Primer Tube Stand
17. Primer Rod and Holder
18. 550 Primer Track Bearing
19. Shellplate Bearing Kit
10 American Shooting Journal // Buyer’s Guide 2017
longstanding symbol of the quality and affordability you have
come to know over the years. Get Zero – and get a whole lot
more! For more information, visit zerobullets.com.
GUNS/PARTS
ABSOLUTE ZERO ORDNANCE, LLC (See ad page 10)
Absolute Zero Ordnance, LLC (AZO) is operated by a father-son team
of veterans. Just over a year old and located in Magnolia, Texas, AZO
is a full-service retail shooting sports store with extensive stock and
full gunsmithing services. AZO is also a custom builder of handguns
and rifles in virtually any caliber, on any platform.
AZO currently mills our own “enhanced” serialized lowers and
contracts uppers, handguards and pistol grips to our design for
AR platforms. We use 7075 billet aluminum alloy to minimize
weight and build stronger, lighter components. And we mill our
own serialized polymer-platform pistols and only use match-grade
components and full hand-fit process to assure a quality handgun.
Our lowers use a screw system to “enhance” user operability for
changing out parts and to eliminate “lost” components, a frequent
problem with typical pin systems. Plus we place a captive spring
in the lower that applies upward pressure to the upper receiver at
the rear takedown pin to eliminate any movement and make the
fit tight between upper and lower, increasing accuracy.
AZO also coats custom guns in a proprietary, very wear-
resistant coating called Blackstone by IA Coatings, which
developed the application methodology. In use by military and
law enforcement, it has been proven extraordinarily durable,
with an elevated level of lubricity. Case studies after firing tens
of thousands of rounds without any lubrication show almost
unbelievable results. AZO uses this coating inside and outside
on both handguns and rifles. For more information, visit
azocustoms.com.
BUYER’S
GUID
E
Absolute Zero Ordnance
38900 FM 1774Magnolia, TX 77355
AZO Patriot AR-10/15 Enhanced Lowers
7075 Billet w/Custom Graphics and Screw
Enhanced Pinning System
RETAIL SHOOTING SPORTS STORE & CUSTOM GUN BUILDER
“ALWAYS SEEKING PERFECTION”
RETAIL SHOOTING SPORTS STORE & CUSTOM GUN BU
AZO Patriot .308 Long Range Precision
346-703-0118azocustoms.com
weight and build stronger, lighter components. And we mill our azocustoms.com.
12 American Shooting Journal // Buyer’s Guide 2017
AMERICAN BUILT ARMS COMPANY (See ad page 15)
Based in Glen Rock, Pennsylvania, American Built Arms
Company markets and sells its A*B Arms brand of high-end
products through a network of dealers, distributors and OEM
manufacturers. The company is a veteran-owned, Type 07/NFA,
US manufacturer of firearms and firearm parts for the civilian,
law enforcement and defense industries. A*B Arm’s philosophy is
“build it in the USA” and “build it better, build it stronger, because
lives are on the line.”
Products include the MOD*X Modular Rifle System,
an aluminum chassis designed for the Remington Model
700 and 783, Howa 1500, Savage Arms Model 10 and
Weatherby Vanguard short-barreled actions. A*B Arms also
manufactures
parts and
accessories for
the AR-15, IWI
Tavor, Mossberg
500 shotgun and
the Remington
870 shotgun.
The A*B Arms
“Power to the
People Program”
allows a buyer to
purchase the MOD*X chassis and the Remington Model 700
SPS Tactical AAC barreled action together to build a quality
dream rifle. For more information, visit abarms.com or email
ARMASPEC (See ad page 3)
Armaspec is
a US-based
manufacturer of
firearm accessories,
primarily for the AR
platform. They focus on producing quality, innovative products
that offer a tactical advantage, at a good price, all made in the
US. Their product line includes magwell grips, charging handles,
slings, tactical buttons, backup sights, and other AR accessories.
For more information, visit armaspec.com.
BARTLEIN BARRELS (See ad page 27)
With a current wait time of five
to six months for a precision
barrel, the word is out that
some of the most precise
barrels commonly used for
hunting and today’s Precision
Rifle Series competitions are
those from Bartlein Barrels.
See these rifles in action at www.DRDTACTICAL.com
COVERT ARM OF THE FREE
WORLDDRD Tactical designs and manufactures precision Sniper Weapon systems and carbine Rifles in the
USA. DRD weapons are in service by US Law enforcement, Government Agencies and US Allied
Countries around the world. With our patented quick take down system, all our rifles can be carried
covertly in brief cases or back packs.
KIVARRI® - 338 LAPUA
PARATUS® - 7.62 NATO
CDR-15 - 5.56 NATODR-15 - 5.56 NATAA O
BUYER’S
GUID
E
americanshootingjournal.com 13
BUYER’S
GUID
E
Custom Guns
“Howdah Single Shot Pistol”
“Howdah Revolver”
The Howdah single shot will be in six of our own big calibers.
“Howdah Revolver”The revolver is built from scratch on our
own stretch frames and is available in several large calibers.
14 American Shooting Journal // Buyer’s Guide 2017
This team of experienced shooters, reloaders and hunters has
been in the firearms industry for years and know the industry
inside and out.
Their uniformity is second to none and their rifling machines
are so accurate they carry the twist rate to the fourth decimal
point, meaning you can have your twist so precise, it measures
1 in 11.3642. Their single-point cut rifling is the most stress-free
method to rifle a barrel, the twist is exact and the bore and
groove dimensions are uniform.
They prelap every barrel before rifling and finish lap
just after. This means you should never need to fire lap or
bore polish your barrel under any circumstances. They also
swear that a lapped barrel will not wear out faster than an
unlapped one, and have found that their barrels will typically
last longer than a button barrel. For more information, visit
bartleinbarrels.com.
DAVIDSON’S GALLERY OF GUNS (See ad page 11)
Davidson’s Gallery
of Guns is the
consumer website
for Davidson’s, one of
the oldest and largest
firearms wholesalers
in the country.
GalleryofGuns.com is
dedicated to helping
you find the perfect
firearm. Here is how it
works: Search from over 90 of the world’s leading manufacturers.
Find your new firearm and get an instant quote from local gun
retailers – no phone calls, emails, or instant messages, just an
instant quote. Buy your new firearm by placing a 25 percent
credit card deposit, and your new firearm will be delivered to
your selected local retailer in as little as 48 hours. GalleryofGuns
.com is not an auction site; it is a fast and convenient way to
purchase brand new firearms. Best of all, each firearm sold
through GalleryofGuns.com comes with Davidson’s Guaranteed
Lifetime Replacement Warranty. Simply put, if anything ever
goes wrong with any firearm you buy from them, it will be
replaced with a new firearm (see website for complete terms
and conditions). With GalleryofGuns.com, you will never want to
search, find and buy any other way.
For more information, visit GalleryofGuns.com.
DRD (See ad page 12)
The Aptus weapon system is a folding-stock, multicaliber rifle
that can go from PDW to
DMR in less than a minute.
DRD’s patented quick-change
barrel system and internal
recoil system in a direct gas-
operated rifle with AR-15 parts
compatibility makes it a perfect
modern sporting or tactical
rifle. For more information, visit
drdtactical.com.
FREEDOM ARMS (See ad page 10)
Freedom Arms Inc. is based in a scenic mountain valley in
western Wyoming, a country of proud traditions and a history of
individualism. Firearms served as a valuable tool here, not just
a recreational item. From this heritage comes the individuals
whose dedication, skill and talent make Freedom Arms revolvers
and accessories unparalleled in their class.
Freedom Arms guns are known for their consistent accuracy,
achieved through engineering and quality control standards
closely adhered to by the company’s committed craftsmen, and
ballistics, which allow a given cartridge to reach its greatest
potential in accuracy and velocity.
We realize that purchasing a Freedom Arms revolver goes
beyond ownership of just another firearm. It is an investment.
Our experienced sales staff is available at the factory to assist
you in making the best choice of revolver configuration to satisfy
your needs. For more information, visit freedomarms.com.
BUYER’S
GUID
E
d velocity.
Freedom Arms revolve
m It is an inve
tory
s.
est
16 American Shooting Journal // Buyer’s Guide 2017
GRENDEL HUNTER (See ad page 20)
Grendel Hunter specializes in providing you with superior 6.5
Grendel uppers to compliment your current rifle. If you already
own an AR-15 and want to maximize its capabilities, one of
their 6.5 Grendel uppers is for you. Grendel Hunter products
are lightweight, rugged and designed to be carried in the field.
Give yourself an edge with the modern sporting rifle. For more
information, visit Grendelhunter.com.
HARDENED ARMS (See ad page 17)
Hardened Arms specializes in making AR-15 and AR-10 rifles, pistols,
barrels, parts and suppressors. They start with 4150 CMV barrel
steel. Each barrel blank is stress relieved and air gauged, and then
coated with Melonite to add additional strength and durability. All
aluminum parts are milled to exacting standards, and are Type II
Class III anodized for the highest quality finish.
Hardened Arms has also dialed in a well-running .300 upper that
is accurate and dependable with either sonic or subsonic rounds,
and their 7.62x39 caliber is known for its accuracy and ability to eat
pretty much any steel case ammo that you could feed it. Hardened
Arms currently offers the following calibers: 5.52/.223, .300 Blackout,
7.62x39, 6.8 SPC II, 6.5 Grendel and .458 for the AR-15 platform.
Their AR-10 platform in the .308 caliber is known for its
precision, and comes in 16-inch and 24-inch barrel lengths. They
are currently completing testing for the release of their AR-10
platform in 6.5 Creedmoor.
Hardened Arms also offers two outstanding suppressors on
the market, the heavy-duty Black Widow .30 caliber and the just-
released Stingray. Their LumaShark AR-15 Handguard is a unique
rail with light tubes for high-lumen Cree lights and/or infrared
bulbs machined right in to the handguard. It has great appeal for
both law enforcement and home defense.
Hardened Arms is known for offering innovative and high-
quality products with great value (they call it “bang for the buck”)
and outstanding customer service. If you are in the market for an
AR rifle or pistol, AR parts or suppressors, give them a try. You will
be glad you did. In fact, they guarantee it. For more information,
visit hardenedarms.com.
BUYER’S
GUID
E
18 American Shooting Journal // Buyer’s Guide 2017
JL BILLET (See ad page 19)
The JL Billet 7075 T6 AR15 Skeletor matched set is machined
to have matching lines between upper and lower to give you a
clean, aggressive look while maintaining the tightest tolerances.
This matched set has weight reduction cuts that give it a look
that stands out among the rest. Weighing in at 15 ounces, this
is the perfect platform for your lightweight build. It doesn’t
sacrifice style or function, and still will stand up to hard use.
Compatible with all Mil-Spec parts and included with all of
the standard JL Billet features, including a hidden anti hand
guard rotation pin, a trigger over-travel adjustment screw,
an upper tensioning screw, an integrated trigger guard, a
threaded bolt catch pin, a threaded take-down detent hole and
a reliable built-in ambidextrous bolt release. The set has full
aesthetic blend from the lower to the upper and upper to all JL
Billet AR-15 hand guards.
Designed for the truly selective builder and shooter, this set
is available in Mil-Spec Type 3 hard coat, or raw in the white,
ready to receive your custom coating option. The Skeletor set
is also available with a built-in, concealed, completely and
easily reversible California-compliant magazine lock. For more
information, visit jlbillet.com.
MATCH GRADE MACHINE (See ad page 24)
At Match Grade Machine (MGM), machinists have been specially
trained to produce the finest custom gun barrels on the market.
Specializing in Thompson Center Encore and Contender, Savage
Pre-Fits and Remage barrels (Remington with a barrel nut, i.e the
Remington 783), these machinists produce the best custom-built
precision barrels available.
Machinists use great care, patience and assiduity during the
turning and contouring processes to help ensure concentricity to
the bore. That is the reason why their barrels are turned on high-
quality manual and CNC lathes. Machining a concentric barrels is
critical when it comes to chambering. MGM chambers to a SAMMI
minimum to give you a perfect chamber that aligns to the bore.
These custom barrels offer some of the best and most precise
shooting available. And at MGM, they offer some great variations,
with the most customization on the market. Their custom gun
BUYER’S
GUID
E
(MATCH GRADE MACHINE)
20 American Shooting Journal // Buyer’s Guide 2017
builder offers you unprecedented options, to get you the best
custom-built barrel available, built exactly how you want it.
Feel free to use their online barrel builder, or shop our on-hand
inventory. For more information, visit matchgrademachine.com.
PICKETT’S MILL ARMORY (See ad page 25)
Pickett’s Mill Armory is a Georgia-based dealer of AR-15 parts
and upper receivers. Pickett’s Mill believes that a high-quality
upper receiver does not have to clean out your bank account.
Their skilled and dedicated staff is comprised of military
veterans and family who together work to provide you the best
tools for your mission. Whether you are in the market for an AR
pistol or a full-length upper receiver, they can build exactly what
you need. For more information, visit pmarmory.com.
REEDER CUSTOM GUNS (See ad page 13)
In the mid- to late 1970s, Lee Jurras brought out his Howdah
pistols in a limited edition series. The Howdah pistol was a
handgun carried by tiger hunters in India. They hunted from the
backs of elephants, and it was not unusual for the tiger to attack
the men riding atop the pachyderms. When that happened,
the Howdah pistol, in a large caliber, would either kill the tiger
or at least get him off the elephant. Lee developed the original
Howdah in five of his own large calibers and chambered them in
a model called the Contender.
Last year, knowing Lee was very sick with cancer, Gary Reeder
of Reeder Custom Guns spent a couple of days with him. Lee
had been a good friend and a mentor to Reeder for more than
BUYER’S
GUID
E
(See ad page 25)
Pickett’s Mill Armory is a G
and
UYYYYYYYYYYYYYYYYYYYYYER
for more than
st
t
22 American Shooting Journal // Buyer’s Guide 2017
40 years. As they talked about their various hunts, the subject
of the Howdah came up and Lee said he would like Reeder to
bring it back. Reeder gladly agreed, as the Howdah was a unique
handgun. As a memorium to Lee – who passed away on April
24 – Reeder Custom Guns now offers Howdah single-shot pistols
and a new Howdah revolver. The revolver is built from scratch
on Reeder Custom Guns’ own stretch frames and is available in
several large calibers. The Howdah single-shot will be in six of
their own big calibers. There will only be 100 of each series made.
For more information, visit reedercustomguns.com.
TANDEMKROSS (See ad page 21)
Take your Smith & Wesson SW22 Victory to the next level
with competition upgrades from Tandemkross, an innovative
manufacturer of accessories for rimfire pistols and rifles. The
“Victory” Trigger offers a textured, flat-faced design to lighten the
trigger pull weight and help the user determine if they are pulling
too far to the left or right, improving accuracy. The “Halo” charging
ring is a simple, drop-in part ideal for competition shooters. The
unique pull-ring design ensures fingers of any size can get a proper
grip and utilize the extra leverage needed to make charging the
pistol or clearing a jam quick and easy.
Make magazine changes during competition easier and faster
with the Tandemkross “Maximus” Plus1 followers, “VictoryPRO”
magazine bumpers and “Titan” extended magazine release.
The Maximus followers allow the user to load 11 rounds in
a standard 10-round magazine, ideal for Rimfire Challenge
competitors, while the “VictoryPRO” Bumpers offer extra material to
quickly and consistently bump the magazine into place. The “Titan”
magazine release is taller and wider than the factory magazine
release button, and offers a textured surface to improve grip.
For more information, visit Tandemkross.com.
THORDSEN CUSTOMS (See ad page 23)
Thordsen Customs is proud to introduce the FRS-15 GEN III
Featureless Rifle Stock. Certain states, such as New York and
California, have passed laws banning or restricting specific
features on semiautomatic rifles like the AR-15. In doing so,
they have made “going featureless” a viable alternative to forced
registration, or worse. Just like its predecessors, the FRS-15 GEN
III is designed to help law-abiding citizens keep their firearms in
compliance with these laws so residents can continue to enjoy
shooting their modern sporting rifles.
The AR-15 platform is based on modularity, and the design
improvements incorporated into the FRS-15 GEN III follow that
tradition. Its design features allow numerous possibilities for
aftermarket add-on upgrades, like sling loops, cheek rises, and
adapters for weapon platforms other than the AR-15.
BUYER’S
GUID
E
(TANDEMKROSS)
americanshootingjournal.com 23
BUYER’S
GUID
E
AR/AK Pistol Cheekrest Kits
thordsencustoms.com
Enhanced Pistol Cheek Rest Kit with CAA saddle shown
650-588-3700
Our Pistol Cheek Rest Kits are a Hybrid design combining our Standard or Enhanced Buffer Tube Covers and the Command Arms SST1 or the Mission First Tactical Evolv Stock Saddle. The two are joined together using a specially designed adapter and mounting hardware.
An inexpensive and easy to install upgrade for short barreled rifle and AR Pistol applications. It redirects high pressure concussion, flame, and hot muzzle gasses forward away from the shooter and bystanders.
Our new Picatinny Buffer Tube Adapter is a great addition to your Sig MPX, Sig MCX, Sig P556XI, Rock River PDS, or any other pistol that utilizes a rear vertical picatinny rail. It gives a shooter the ability to add a cheek rest for greater stability or a stock for SBR conversions (federal tax stamp required).
Stability and Accuracy
Picatinny Buffer Tube Adapter
BD-180 Blast Deflector Kits
The result is a rock solid, ergonomic, cheek weld that provides stability for accurate, repeatable, shooting and a proper sight line for your favorite optics or sights. Our kits come pre-assembled in house with new, easy to follow, instructions on the inside flap of the new header card. Instructional videos are also available on our website.
The BD-180 is unique because it can be installed between your existing A1, A2, and 3 pronged flash hider and the barrel, eliminating the need to buy an entirely new muzzle device. It can be used in place of or in conjunction with a crush washer for a secure connection and proper timing. At 1.35 inches in diameter and weighing in at a mere 2 ounces, it will fit inside most low profile or lightweight foreends without adding significant weight.
The mounting method follows true STANAG (NATO Standardization Agreement) protocol using the two back angles and the top of the rail as the contact points. The result is perfect alignment with the centerline of the firearm. A feature that is not attainable with typical side clamping adapters. Another bonus is that there are no visible fasteners or holes on the top and sides of the adapter giving it a clean sleek look.
24 American Shooting Journal // Buyer’s Guide 2017
Buy Online or Contact Us Directlymatchgrademachine.com • 435-628-0071 • [email protected]
PRECISION BUILT GUN BARRELS
Specializing in Custom Gun Barrels: Here at MGM, our machinists can produce the best premium custom Savage, Remage and T/C Encore/Contender barrels on the market. Feel free to use our online barrel builder, or shop our on-hand inventory.
Thordsen offers several base kits that are available in
black, flat dark earth, and OD green. The upgrade kit is
a direct swap upgrade from GEN I and II stocks to the
GEN III, and their standard and enhanced carbine kits
are designed for carbine length recoil systems. A rifle-
length kit is designed for rifle length (A2) recoil systems.
The gas piston kit is designed for forward-sprung recoil
systems that do not require a buffer tube. For more
information, visit thordsencustoms.com.
TURNBULL (See ad page 16)
It was once believed that tampering with an original
firearm would detract from its value, even if time and heavy
use had taken its toll. It was thought that no one could possibly
duplicate the original firearm finishes or the craftsmanship of the
original guns.
Turnbull Restoration is committed to honoring early
gunmakers by returning these classic firearms to their original
beauty. Restoration of guns involves a great deal of knowledge,
skill, patience and a keen eye for detail. When done correctly,
restoration can provide a look into the past while preserving an
important piece of history.
This unyielding dedication to quality goes into the Turnbull
Finished series as well. This series consists of historically
BUYER’S
GUID
E
americanshootingjournal.com 25
BUYER’S
GUID
E
If you’re looking for AR replacement parts or other tactical gear, Pickett’s Mill Armory is your one-stop online gun shop. Whether you just need a new bolt carrier to install independently or an entire in-house, custom-built upper receiver, we offer all types of AR parts for sale from the best brands out there today.
FREE SHIPPING ON ITEMS OVER $100
AR15 & AR10 PARTS &
ACCESSORIES
WWW.PMARMORY.COM
16” 5.56 UPPER RECEIVER 15” MLOK RAIL
16” 5.56 UPPER RECEIVER 15” KEYMOD RAIL
10.5” UPPER RECEIVER WITH KEYMOD RAIL .223 WYLDE
$289.99
$279.99
$289.9916” 5 56 UPPER
$289.99
16” .300 AERO PRECISION UPPER RECEIVER 12” QUANTUM RAIL
16” 5.56 AERO PRECISION UPPER RECEIVER 12” QUANTUM RAIL
PMA 7.5” M4 KEYMOD RAIL PISTOL UPPER .223 / 5.56
$329.99$259.99
$319.99
PMA 7.5” KEYMOD RAIL PISTOL UPPER .300 WITH FLASH CAN
PMA 7.5” KEYMOD RAIL UPPER RECEIVER .300 BLACKOUT
PMA 7.5” .223 WYLDE UPPER RECEIVER
$289.99$279.99 $259.99
26 American Shooting Journal // Buyer’s Guide 2017
significant and iconic firearms that are finished using our color
case-hardening process and other signature finishes, producing
a classic gun worthy of being an instant family heirloom. The
Turnbull Finished series currently includes the Ruger Mark IV,
Winchester 1873, Winchester 1892, Marlin 1895 and Marlin 336C.
For more information, visit turnbullrestoration.com.
WHITE OAK ARMAMENT (See ad page 27)
At White Oak Armament, we made our
reputation by providing award-winning
barrels to the high-power competition
community. Now we use that expertise to
design barrels for other shooting disciplines,
including hunting.
Each White Oak barrel starts with a
stainless-steel, match-grade lapped blank to
give you the best barrel possible. The White
Oak line of Varmint and Predator barrels
are extremely accurate and are available in
lengths from 18 inches to 26 inches.
We have also introduced a purpose-built
18-inch 3-Gun barrel that will deliver the
match-grade accuracy White Oak is known
for, in a lighter weight barrel. Our SPR and
SDM barrels are designed for the military-law
enforcement market, but make a great barrel
for the casual shooter as well.
Complete uppers are also available with
any of our barrels. For more information, visit
whiteoakarmament.com.
GUN ACCESSORIES
ACCURACY SOLUTIONS (See ad page 29)
With BipodeXt, you will have a rifle-shooting experience unlike
anything before. This revolutionary new product provides
shooters with unmatched stability and accuracy.
To understand the principles behind the design of BipodeXt,
it helps to visualize a rifle as a lever and its bipod as the fulcrum
on which the lever rests. While BipodeXt is not utilized to lift
weights, an analogy from the lever/fulcrum axiom can still be
drawn. As for the lever, the closer the fulcrum is to either end of
the lever, the more leverage the user obtains. As for BipodeXt,
the further out the bipod is placed, the more stable sighting
down the rifle’s scope becomes.
Some BipodeXt models, such as the BXT 40X3, provide for a
bipod’s resting point to be placed beyond the muzzle of most
rifles, thus further minimizing movement through the rifle and
impressively reducing reticle drift. BipodeXt can be extended
and retracted, giving the shooter a highly adjustable and
customizable resting point. Due to its round design BipodeXt
can quickly correct canting by simply operating its clamp’s
lever. This also allows for an unprecedented 360 degrees of
rotation of the bipod in relation to the rifle. Most models
weigh approximately 11 pounds. For more information, visit
accuracysolutions.com.
ARACHNIGRIP (See ad page 27)
The Slide Spider, by Arachnigrip, is a patented one-piece
adhesive grip wrap for semiauto pistol slides. The grip is
designed to enhance safety and control in the operation of the
BUYER’S
GUID
E
26 American Shooting Journal // Buyer’s Guide 2017
27)
our
ng
n
e to
plines,
k to
te
ro
w
ac
ARAThe
adhe
desi
(ACCURACY SOLUTIONS)
americanshootingjournal.com 27
BUYER’S
GUID
E
Bartlein Barrels, IncManufacturers of Precision Single-Point Cut Rifled Barrels
On the Cutting Edge of Barrel Technology!
W208N16939 N. Center StreetJackson, Wisconsin 53037
262-677-1717BartleinBarrels.com
Wor
ld Record Barrels
Precision Single Point Cut Rifl
ing
28 American Shooting Journal // Buyer’s Guide 2017
handgun. The Slide Spider enables the shooter to gain increased
control through a safe and secure hold. The product offers
additional tactical advantages under challenging operating
conditions, including extreme moisture and temperature.
In addition, the product aids shooters with weak or weakened
hand strength and those with medical conditions such as arthritis.
Arachnigrip offers a variety of designs to fit most semiautomatic
handguns, and also offers custom imprinting on the product. For
more information, visit arachnigrip.com.
ELITE IRON (See ad page 29)
Located in the beautiful Potomac Valley of western Montana,
Elite Iron is a premier manufacturer of professional-grade
sound suppressors designed to provide enhanced accuracy
and superior sound reduction. Elite Iron suppressor models
cover .17 HMR through .50 BMG and all favorite hunting
calibers in between.
Elite Iron’s experienced shooting staff has an excellent
knowledge of ballistics, and can assist customers in choosing the
right suppressor for all of their shooting needs.
Elite Iron produces products “of a higher caliber,” adhering to
the highest quality standards of manufacturing. Their meticulous
attention to detail in all phases of manufacturing assure on
target results from all of their products.
Elite Iron was the first to offer a suppressor mirage mitigation
and heat wrap that are available in a wide range of sizes.
Elite Iron offers a patented Revolution bipod that revolves 360
degrees around the rifle barrel while still maintaining the axis
to move left to right and up and down. It is available in both
standard and panning models.
For those occasions when being quiet about your shot
is not a requirement, our full line of muzzle brakes will keep
you on target round after round. For more information, visit
eliteiron.com.
RIO GRANDE CUSTOM GRIPS (See ad page 31)
Rio Grande Custom Grips is on the cutting edge of grip design
with full-color, full-coverage images never before seen on
handgun grips. You can now add pizzaz to your Beretta 92, 96,
and M9 pistols. All of their Beretta 92-series grips are compatible
with ambidextrous safety and incorporate the RioGrip texture.
RioGrip is a series of recessed ovals that provide a grip with more
bite than smooth grips without sharp edges, like checkering, that
can catch on clothing. Rio Grande currently sells grips for the
1911 full-size pistol and clones, full-size Bobtail 1911 pistols, the
Taurus PT1911, Compact/Officer 1911 pistols, the Sig Sauer P938,
Ruger Vaquero, New Vaquero, Blackhawk, Super Blackhawk,
Single-Six, and 22/45 Mark III. For more information, visit
RioGrandeCustomGrips.com.
GUN CLEANING
AUDEMOUS FROG LUBE
(See ad page 33)
FrogLube bio-based cleaning and lubrication products
are insurance your firearm will work 100 percent of the
time. FrogLube solvents do the work instead of you having to use
scores of cleaning tools, adapters, scrapers and picks.
BUYER’S
GUID
E
ng the
ering to
n smoo
tch on clothing
full-size pistol and clo
rus PT1911, Compact/Officer
uger Vaquero, New Vaquero, Blackhaw
Single-Six, and 22/45 Mark III. For more infor
RioGrandeCustomGrips.com.
americanshootingjournal.com 29
EliteIron.com (406) 244-0234
STFU.UnitSpecial Tactical Forward
training exercise, the STFU (Special Tactical Forward Unit) is rapidly gaining popularity among both the professional and civilian shooter. The .30cal STFU rivals its big brother the BRAVO in producing almost the same level of sound reduction in a shorter length.
The new design has virtually eliminated the POI shift. Primarily designed for 7.62, 30-06, 6MM and 6.5
have a 24” barrel.
We also offer the Titanium model STFU LITE.
BUYER’S
GUID
E
BipodeXt.com#accuracyextended
I s N o w
(714) 988-7985
30 American Shooting Journal // Buyer’s Guide 2017
Place FrogLube degreasing solvent or Super Degreaser
alongside FrogLube CLP lubricant in your kit. Check out
their performance by submersing your gun parts in a tub of
Solvent or Super Degreaser. Immersion places the cleaner in
areas you can’t reach or see. Wait 10 to 15 minutes to allow
the cleaning action to occur. Remove the firearm part, shake
or blow it dry and apply your lube. There is no easier, quicker
or more complete maintenance system for firearms. For more
information, visit froglube.com.
GTUL (See ad page 31)
GTUL specializes in products to clean and
maintain magazines for pistols and high-
capacity rifles. We offer the finest brushes in
the market, along with metal punches to ease
the take down of your magazines. Our pistol
brush will work with all centerfire single stack
and double stack magazines.
A patented device to release the locking
tabs on Glock magazines works with both
standard and extended floorplates, and is
the only one available able to handle both chores. Available
for all Glock models, GTUL releases the locking tabs and
to help ease removal of the floorplate and maintain the
integrity of your Glock floorplates.
The slide removal tool works with all Glock models and
engages both standard and extended slide locks, to ease
removal of your slide for cleaning. It is helpful to those with small
or large fingers, and those whose fingers are worn and seasoned.
Our magazine brush for high-capacity rifle magazines fits both
5.56 and 7.62mms, and works with AR, AK, FAL magazines and
more. The U-shaped brush is 9 inches long, is stout enough to
depress the follower and magazine spring without disassembly,
and is long enough to clean 40-round magazine.
Our products are proudly made in the USA. For more
information, visit mygtul.com.
IOSSO (See ad page 31)
Iosso’s AR-15 and AR-308 Rifle Cleaning Kit cleans the gas tube
without disassembly, and five other hard-to-clean areas!
The kit contains six precision-fit brushes to clean the upper
receiver, chamber, bolt carrier, bore, bolt carrier key tube, and
BUYER’S
GUID
E
americanshootingjournal.com 31
BUYER’S
GUID
E
IOSSO PRODUCTS www.iosso.com 888-747-4332
AR-15 CompleteCleaning Kit
The 100% Accurate Way Way to Clean
Includes precision fit brushes & cleaning tools gas tube brush & guide tool
bolt carrier & chamber brush
bolt carrier key brush
upper receiver brush
.223 bore brush
cleaning rods
storage pouch
Use with the Iosso Triple Action Oil and Iosso Bore Cleaner, sold separately.Patent #US 8,458,947 B2
Clean the Gas Tube Without
Removal.
Made in USA
32 American Shooting Journal // Buyer’s Guide 2017
gas tube. The gas tube brush inserts easily into the guide tube
to clean the entire length without disassembly of the upper
receiver. Using the gas tube brush with the Eliminator Triple
Action Oil will remove carbon build-up. The brushes are made of
a premium blue fiber which is a trademark color of IOSSO, and
the kit is patented technology.
The kit also includes a versatile handle, extension rod, bore
rope, and patch puller. These tools will allow complete cleaning
of any pistol, rifle, or shotgun. An accessory pouch is included to
carry all of the components.
The Iosso Bore Cleaner and Eliminator Triple Action Oil
are recommended cleaners to be used with the kit and are
sold separately. Both products are bio-based and are made
from plant extracts. While safe to the user, it also keeps our
environment healthy.
Suggested list on this kit is $68.99. For more information, visit
iosso.com or call toll-free (888) 747-4332.
HOLSTERS/CONCEALMENT
DEEP CONCEAL (See ad page 35)
Steve Morrow was looking for a truly concealed shoulder holster
or shoulder harness that could be comfortably worn under
a dress shirt. What he found was either poorly made, poorly
designed, uncomfortable or didn’t conceal his firearm. Left with
no real choices, he designed his own product, and Deep Conceal
was founded in 2009.
Ever since, the company has been an innovator in shoulder
holsters/harness for men and women, holsters for the car,
for travelers, for the home and office, for a woman’s bra, and
shirts. Deep Conceal has sold products to individuals and
police departments worldwide, including the United States
Department of Homeland Security.
Made from commercial-grade cotton, Deep Conceal products
are very comfortable and durable. The new Universal Harness
for men and the BobCat Harness for women both include
detachable holster pockets that allow the user to carry a large
firearm one day and, with a simple holster pocket change, carry a
small firearm the next. The company’s success has allowed them
to manufacture non-firearm-related products as well.
All products are priced below $50 including shipping, and all
orders come with a 30-day unconditional guarantee. For more
information, visit deepconceal.com.
DESIGNER CONCEALED (See ad page 35)
Since entering the market in 2009, Kate Woolstenhulme of
Designer Concealed Carry has established a devoted customer
base among women and men who desire stylish, high-quality
concealed carry bags. Careful consideration has been given to
the specific requirements such as adjustable shoulder straps for
proper positioning, adjustable holster to fit various sizes and
types of handguns, dual lockable zippers for both left- and right-
handed access to the holster
pocket and interior features to
support situational awareness.
With retail pricing
from $279 to $4,200 (for
exotics), there is something
to fit every budget and
lifestyle. Exclusively available
through retail gun stores or at
DesignerConcealedCarry.com.
For dealer information, email
Kate@DesignerConcealedCarry.
com or call (972) 672-9437.
BUYER’S
GUID
E
americanshootingjournal.com 33
BUYER’S
GUID
E
SNAGMAGConcealed Magazine Holster
The SnagMag™ is designed to look like a knife riding in your support-side front pocket along the outside seam.
n
Order Now at Snagmag.com
LEO and Military Discounts | Limited Lifetime Warranty | email: [email protected]
• Convenient and Comfortable• Carries Like a Pocket Knife• Designed for a Fast Draw• Lightweight yet Durable
• Discreet Way to Carry an Extra Magazine
SPECIAL OFFER! Use the Coupon Code: buyersguide5 for $5 off
34 American Shooting Journal // Buyer’s Guide 2017
DM BULLARD LEATHER (See ad page 35)
DM Bullard’s products are made in Azle, Texas, from the finest
gun leather. Are you looking for that new leather holster, belt,
rifle sling, cowboy rigs, cartridge belts, wallets or knife sheaths?
DM Bullard’s are handmade from beautiful, 100 percent
Hermann Oak leather right in their shop. Choose from a variety
of exotic skins, bull hides and custom hand tooling and multiple
color choices. For more information, visit dmbullardleather.com.
SNAG MAG (See ad page 33)
SnagMag, LLC
had an unlikely
beginning. More
than four years ago,
the inventor created
the SnagMag for
himself and a couple
of interested friends.
When it fell into the
hands of some very
influential people
in the gun industry,
he was urged to get
a patent and start a
business – the rest
is history. Run by a
husband-and-wife
team, this unlikely
little company cares
about every customer, is grateful for every sale, and desires to
help carriers be prepared and stay safe.
The SnagMag concealed magazine holster is the original,
front-pocket mag holster designed to look like you’re carrying
a pocketknife. Concealed in plain sight and designed for a fast
reload, the SnagMag doubles your ammo without adding bulk
to your belt. The lightweight and durable design is comfortable,
convenient and an EDC must-have. The SnagMag is fully
patented, proudly made in the USA, and the company provides
stellar customer service. SnagMag makes holsters to fit more
than 80 popular gun magazines. If they don’t have your gun
model listed at online they offer custom fitting at no extra
charge. LEO and military discounts and new dealer opportunities
are always available. For more information, visit Snagmag.com or
email [email protected].
ULTICLIP (See ad page 46)
Ulticlip is proud to announce the latest advancement in holster
clips, Ulticlip XL, based on the company’s award-winning
retention system. Ulticlip XL is the world’s first multitool holster
clip and locking steel belt loop. No longer do you have to choose
between a holster clip or belt loop. With the Ulticlip XL you
can have both. The locking belt loop allows the user to carry a
holster, knife sheath or accessory IWB (inside the waist band),
OWB (outside the waist band), or without a belt.
Ulticlip XL’s multitool has a screwdriver and multistage
wrench. Ulticlip XL’s unique mounting bracket (along with its
multitool) allows the end used to change the ride height, and
rotate or reverse the item they are carrying at any time.
Ulticlip XL is made of high-quality spring steel. Rated at over
200,000 pounds per square inch tensile strength, Ulticlip XL
provides guaranteed durability. Ulticlip is proudly made in the
USA. For more information, visit ulticlip.com.
BUYER’S
GUID
E
americanshootingjournal.com 35
BUYER’S
GUID
E
BRAT (bra holster) The BobCat (women’s harness)
Universal Harness Sun Visor Holster
The UNIVERSAL Harness is what we have ALL been waiting for. It allows you to mix and match holster and mag pockets.
Our Sun Visor Wrap Holster is
size from 2.5” – 5.” and is used on either the driver or passen-ger visor.
Deep Conceal, LLC
P.O. Box 833Layton UT 84041
36 American Shooting Journal // Buyer’s Guide 2017
OPTICS/OPTIC MOUNTS
AMERICAN DEFENSE (See ad page 39)
American Defense Manufacturing is a Wisconsin-based
manufacture of optical, illumination, and target-acquisition
device mounts. In addition to their patent quick-detach
mounts, American Defense also manufactures a complete line
of Universal Improved Carbines in the most popular calibers.
The Universal Improved Carbine, as well as ADM quick-detach
mounts, are used by various military units, all levels of law
enforcement, and by responsibly armed citizens worldwide.
American Defense prides itself on attention to detail,
craftsmanship and value. Being a true manufacturer, ADM is able
to pass cost savings along to its dealers and end users.
For dealer inquiries, email [email protected]. For general
sales, contact [email protected]. For more information, visit
admmfg.com.
MARCH OPTICS (See ad page 37)
March Optics has found a way to improve upon perfection with
their new High Master line. The company’s new 10-60x scope
features the same mechanical precision and user-friendly design
as their match-winning 10-60x52mm scope, but they’ve taken
things up a notch with a larger 56mm objective lens for even
more amazing light-gathering ability than before.
Meticulously designed and individually hand-assembled
by the expert engineers at March, these scopes feature a
new Super-ED, high-refractive glass for unparalleled quality
and exceptional clarity. This high-tech glass greatly reduces
chromatic aberration for a previously unheard of level of
sharpness and brilliance that you truly need to see to believe. For
more information, visit marchoptics.com.
BUYER’S
GUID
E
(MARCH OPTICS)
38 American Shooting Journal // Buyer’s Guide 2017
ULTIMAK (See ad page 38)
UltiMAK started in a musical instrument
repair shop as a way of improving the
personal arms of one of the owners.
After the first mounts were hand-made,
it became apparent that everyone could
benefit from the designs. Thus, UltiMAK
now provides “Practical, elegant, affordable,
designs for better living.” That is a fancy way
of saying that UltiMAK allows for the use
of modern optics on several classic, well-
proven rifles and carbines in ways that were
previously difficult, clumsy or impossible.
The forward mounting position
provides the ideal location for a 1x reflex
or holographic sight, or a “scout” scope,
keeps the optic system out of the way of
the receiver mechanism, leaves the factory
iron sights intact, and maintains a low
profile with good cheek weld and minimal
added weight. Thus, and UltiMAK-enhanced
firearm makes the ideal knockin’-around
rifle or carbine, truck carbine, 3-gun match
carbine, or personal defense rifle for the
home. In the appropriate caliber, it also
makes the ideal hunting rifle for the woods
and hills. UltiMAK currently supports the AK platform in several
variations, the M1 Garand, M-14/M1A, Mini-14 and 30, and the
M1 .30 Carbine.
For more information, visit UltiMAK.com.
TARGETS
CUSTOM METAL PRODUCTS (See ad page 41)
The X-Ring Plate Rack from Custom Metal Products features
an innovative reactive X-Ring inside the standard 8-inch plate
target. Shoot the center of the target and only the 4-inch X-Ring
will fall. If you miss the X-Ring and hit the 8-inch outer plate,
both targets will fall. Fine-tune your plate rack skills with this
challenging target.
The targets are made from 3⁄8-inch AR500 hardened steel for
long life with pistol or rifle shooting. The X-Ring Plate Rack is
available with manual reset, or fully automatic pneumatic reset
with competition controller.
The X-Ring Plate Rack was introduced at the NRA Bianchi Cup
competition in late May 2017. All competitors were invited to
shoot the X-Ring Plate Rack at the event.
Overall size of the unit is 123 inches wide by 46 inches deep
by 56 inches high. Shipping weight is approximately 600 pounds.
The price is $2,500 for the manual reset unit, and $5,000 for the
fully automatic unit.
For more information, visit custommetalprod.com.
TANNERITE (See ad page 41)
The handcrafted, one-of-a-kind Tannerite Bunker Box is
constructed from western red cedar and is branded with the
BUYER’S
GUID
E
The X-Ring Plate R k fr tom Metal Products
an innovative re side the standard 8
target. Shoot th nter of th rget and only the
ill f ll I h 8 i h
e
ry
mal
nced
d
atch
he
o
woods
an
va
M
40 American Shooting Journal // Buyer’s Guide 2017
Tannerite logo on the front and the lid. There will only be 5,000
of these limited edition boxes made. This box is not just made to
be a collectible for you to enjoy, but for practical use for you to
use over and over. It is constructed with various compartments to
hold your Tannerite Brand targets, safety supplies, ammo, and to
transport any trash that you may accumulate while shooting to
the nearest trash receptacle.
But wait, not only do you get the collectible box, but you
will also receive the following: eight 1-pound Tannerite targets,
one mixing container, one limited edition Tannerite hat (only
available in this Bunker Box), two pairs of Tannerite safety
glasses, two sets of ear plugs and two Tannerite bumper stickers.
You’ll also receive one of the five Tannerite “mystery” gifts
valued between $15 and $30. Try to collect them all! For more
information, visit tannerite.com.
XSTEEL TARGETS (See ad page 42)
The EZ target system
from XSteel Targets
is extremely easy to
set up and great fun
for all pistols and
rifles rated up to .308
Win. The entire EZ
target system is made
from AR500 steel
that is cut using a
CNC laser. The target
stand has multiple
slots, allowing for the
included 12-inch-by-
20-inch target to be
set up vertically or
at an angle. It’s easy
to carry and requires
no screws or bolts for setup. The EZ target system comes cut
with 20- and 30-degree and vertical slots for angled-down
use up to 70 yards with a .308. All parts are made from AR500
steel (the strike face is made from 3⁄8-inch AR500, and the base
stands from ¼-inch AR500). Handles are cut into strike face
and bases for easier carrying, and the system pulls apart and
stacks for space saving storage. For more information, visit
xsteeltargets.com.
MISCELLANEOUS
CAMOUFLAGE FACE PAINT (See ad page 45)
In the high-tech military world of smart bombs and night
vision goggles, camo face paint remains one of the most
elemental pieces of a soldier’s equipment. Developed and
tested on surfers for its waterproof qualities, Camouflage Face
Paints are odorless, non-glare and easily wash off with soap.
Working closely with the government, creator Bobbie Weiner
developed face paints for soldiers to use on multiple terrains. The
product line consists of woodland, desert, ACU, scorpion, jungle
and multi-camo compacts with an unbreakable mirror, small and
jumbo face paint sticks and powders.
Members of the hunting industry approached Bobbie
Weiner’s Camouflage Face Paint, and today hunters can
get the same face paint supplied to the US Military. Bobbie
Weiner has also developed a line of Sports Fan Custom Color
Makeup for fans to paint their faces at sporting events to
show their team spirit.
Bobbie Weiner’s Camouflage Face Paints sell internationally
on a global scale. You can be assured of the quality and
commitment she has for all of her products. All were
developed in the United States, and have always been made
in America. For more information, visit camofacepaint.com or
call (877) 625-3879.
BUYER’S
GUID
E
42 American Shooting Journal // Buyer’s Guide 2017
LIBERTY SAFE (See ad page 1)
Liberty Safe is America’s
No. 1 producer of heavy-
duty home safes, gun
safes, fire safes and
commercial safes. Join
the more than two
million homeowners
who have found the
peace of mind that
comes from owning
a Liberty Safe. When
people search for a
safe to buy as their
home vault they shop
at Liberty because of
the quality, reliability
and service received.
Just read the more than
15,000 reviews online
and you’ll see why
Liberty has a 98 percent
customer satisfaction
rating. There is nothing
like owning a Liberty
Safe with value and
features at a great price.
When it comes to the sale of the best heavy-duty security
and fire protection safes, there’s nothing like a Liberty. Liberty
offers more than 30 models of the finest home, security and gun
safes, available in more than two dozen colors. And with more
than 450 dealers nationwide, in-home delivery and custom
installation services make owning a safe more convenient than
ever. It’s no wonder more people buy a Liberty Safe more than
any other safe brand.
Owning a Liberty Safe has never been easier with their
12-months interest-free financing program OAC. For more
information, visit libertysafe.com.
LYMAN PRODUCTS (See ad page 43)
Lyman is proud to introduce a whole line of shooting accessories
to help create a stable shooting platform in almost any situation.
How often do you set up shooting rests at the range, only to
find that your rifle isn’t at the proper height? Lyman’s Bag Jack
is designed to make it easy to adjust the elevation of your rifle
and bring it into line with your target, while also allowing you to
maintain a comfortable shooting position. The Bag Jack corrects
the height with a simple turn of the adjustment knob. The lift is
made from sturdy aluminum and steel components and has a
nonslip textured platform.
Lyman Shooting Bags are made from heavy-duty, 600D nylon
with micro-suede padding on rifle contact points and a nonslip
rubberized base. The Match Bag is equipped with a sturdy carry
strap and an adjustable tensioning strap to adjust elevation. The
Wedge Bag is used to raise or lower the buttstock of your rifle to
BUYER’S
GUID
E KICK-EEZ (See ad page 47)
The Dash-EEZ pad from Kick-EEZ is truly a “miracle” pad. Made
of 1⁄8-inch solid Sorbothane, the Dash-EEZ was originally
created to keep binoculars in place on the dashboard of
hunters’ vehicles as they maneuvered around rough and windy
hunting roads in search of big game. The Dash-EEZ works
equally well with cell phones, eyeglasses, cameras, keys, or
anything else you need to place on the dashboard of your
vehicle and never worry about it falling off.
The Dash-EEZ is
extremely flexible
and its small size (5.9
inches by 5.9 inches
by 1⁄8 inch), and easily
conforms to any
dash size or shape.
The miracle pad
never loses its ability
to adhere to your
dash, and cleanup is
super easy; simply
wash with soap and
water and replace on
your dash. For more
information, visit
kickeezeproducts.com..
44 American Shooting Journal // Buyer’s Guide 2017
correct your aim point. The Crosshair Front Bag provides a stable
front rest for any rifle. The Crosshair Rear Bag features a notched
design that holds the rifle stock in place. For more information,
visit lymanproducts.com.
PRESENT ARMS (See ad page 45)
Present Arms Inc. – known for the design of mission-specific
armorer plates for HK, Sig, Beretta, M&P, the 1911 and their
flagship Gunner’s Mount for the AR – are pleased to announce a
new product line. The Sentinel Plates are a cost-effective universal
stand to display and clean firearms. Their patent-pending
Sentinel Plates are a simple platform that incorporates an already-
patented universal mounting system by accepting their magazine
post for the AR, and the ever-growing number of pistol posts.
Sentinel Plates come in two sizes: large for rifle and handgun,
small for handgun only. Use it for display, cleaning, servicing, or
building that lower AR. One side is smooth for display, while the
other has a cut pocket to eliminate runaway parts. It accepts a variety
of interchangeable magazine posts. You can take it to the range, as
it fits in a range bag. It’s the last stand you’ll ever need. Sometimes
you just need a third hand. Sentinal Plates start at $39.95. For more
information, visit presentarms.com or call (413) 575-4656.
WARREN CUSTOM OUTDOOR (See ad page 45)
Warren Custom Outdoor was started
in 1998 by husband and wife Paul and
Yvonne Almashy. The pair started out
by setting up at area gun shows, and
soon had their own website offering
their products online. They decided
from the start that they would offer
only top-quality products made in USA
and that were not generally available
in chain stores or national mail order
catalogs. All products offered have
been personally tested and found to be of the highest quality.
They are sole distributors for two products made in Ohio. The
first is Mag Spark replacement nipples for caplock muzzleloading
rifles, allowing use of 209 shotshell primers instead of the
unreliable No. 11 caps. The second is One Hole Sights, which
are replacement aperture blades for adjustable rear sights on
many Rugers, Winchesters and Marlins. The One Hole aperture,
or ghost ring sights, relieve eye strain and allow you to shoot
more accurately and faster than with your standard blade rear
sight. You can dramatically improve your shooting without the
weight and bulk of a scope.
Other top-quality products available include: Bright Sights
gunsight coatings (made in Oregon), Smokey’s Deer Lures and
trapping baits (West Virginia), Woodman’s Pal (Pennsylvania),
Fulton Flashlights (Ohio) and Sure Shot Sprayers (made in
Wisconsin by Milwaukee Sprayer Company since 1932). For more
information, visit warrencustomoutdoor.com.
BUYER’S
GUID
E (LYMAN PRODUCTS)
americanshootingjournal.com 45
BUYER’S
GUID
E
Warren Custom Outdoor
DEALER INQUIRIES WELCOME
Since 1998 • All Products Made In The USA
330-872-1475330 872 1475warrencustomoutdoor.com
One Hole Sights
Bright Sights
g• Relieve Eye Strain• Shoot More Accurately Without The Weight & Bulk Of A Scope
Bright Sights high visibility gun sight coatings increases the contrast between the front and rear sights, and the contrast between the sights and the target
Replacement Nipples That Allow Use Of Shot Shell 209 Primers In
Also Available: Smokey’s Deer Lures & Trapping Baits, Fulton Flashlights, Sure Shot Sprayers, Woodman’s Pal, Radocy Takedown Guides
Replacement NippleMag Spark
the last stand Our Sentinels plate with interchangeable magazine posts
is the last stand you’ll ever need. For display, cleaning, taking to the range or building a lower AR.
Presentarmsinc.com • 413-575-4656 • Wilbraham, MA
Starting at $39.95