TETRACUBE PANEL X-POL ANTENNACONFIGURATION 2X1

375 ÷ 400 MHzPOLOMARCONI offers a very wide range of wireless products.Our products can be tailored according to the customer’s need.

Made in Italy. We reserve the right to modify these data without any notice.BY

17400021

PMR

1 / 2

17400021-DS REV. 07 - 03/06/2015

Electrical Specif ications

Frequency band (MHz) 375 ÷ 400

Bandwidth (MHz) 25

Input impedance (Ω) 50

VSWR (of the entire 2x1 array system) ≤ 1.5:1

Continuous Max. Power (W) 500

Isolation between channels (dB) (of the entire 2x1 array system) > 30

Polarization (deg) ±45°

Gain (dBi) (of the entire 2x1 array system) 2 x 9.2

HPBW (°) - H-plane (of the entire 2x1 array system) 109

HPBW (°) - E-plane (of the entire 2x1 array system) 37

Front-to-Back ratio (dB) > 27

Electrical Down Tilt (deg) 0°

Intermodulation 3rd/5th order (dBc) @ 2x43 dBm <-150 / <-160

Operation Temp. Range (°C) -40° ÷ +70°

Mechanical Specif ications

Connectors 4x7/16 f

Dimensions (Height x Width x Depth, mm) 835x520x430

Weight antenna structure (kg) 8

Wind load (N) @ 200 km/h Frontal / Lateral / Rearside418 / 260 / 444

Radiation Patterns(of the entire 2x1 array system)

DESCRIPTION:

TETRACUBE panel X-pol antenna.

The design of TETRACUBE antenna is based on fundamental engineering knowledge and also on practical experience, during which the various constructions and materials used have proved their outstanding reliability. Designed to operate on the environmental conditions as described in ETSI 300 019-2-4.

The radome that covers the internal components is made of Polycarbonate material that guarantees optimum performances with regards to stability (tested in accordance to DIN EN ISO 4892-2), stiffness, UV resistance and best weather protection.In case of very light colours, it is possible to apply a further transparent varnish 2K scratch resistant, to further increase the UV protection and further delaying the yellowing of the material.

Four inputs, wide HPBW angle and high Front-to-Back ratio.

Reduced dimensions and light weight.

DC grounded from lightning protections.

STEP 1: Take the radial, pre-installed on its appropriate support

STEP 2: Take the two M6 screws and the proper Allen key contained within the antenna mounting kit

STEP 3: Take the thread locker contained within the antenna mounting kit

STEP 4: Deposit a sufficient amount of thread locker on the threads of the two M6 screws provided in the antenna mounting kit

STEP 5: Place the radial support in its suitable position at the center of the mechanical support structure of the 2x1 array antenna, in correspondence of the two proper fixing holes. Tighten the two M6 screws provided in the antenna mounting kit, with the proper provided Allen key, in both their appropriate locations.

STEP 6: Final TetraCube 2x1 array antenna structure 17400021

pre-installed radial

support

provided M6 screws and Allen key

M6 screws proper

locations

center of the mechanical

support structure of the

2x1 array antenna

TETRACUBE PANEL X-POL ANTENNACONFIGURATION 2X1

375 ÷ 400 MHzPOLOMARCONI offers a very wide range of wireless products.Our products can be tailored according to the customer’s need.

Made in Italy. We reserve the right to modify these data without any notice.BY

17400021

PMR

2 / 2

17400021-DS REV. 07 - 03/06/2015