QUICK START

Suitable for:

OEM Integration OEM Installation Retro Fit Installation

DTI AngleBlaster release 1.1DTI 2010

Reference Guide

QUICK START Reference Guide

Contents:

Introduction ................................................................................................................... 2

Saving Template Hole Angle Values ........................................................................... 2

Drilling Consecutive Holes .......................................................................................... 3

Screen Navigational Guide

Drill Screen & Gauge View .............................................................................. 4

Entering or Selecting a Project File ................................................................. 4

System Setup, Zero Offset & Screen Prefences ............................................ 5

Ring And Dump View Only (Default) ............................................................... 5

Contact Us ................................................................................................................... 6

Quick Start Guide is a simplfied version of the full Operators Manual designed for fast reference on the fly.

Read and familiarize yourself with the full Operators Manuals instructions and information for the proper operation of the DTI Angleblaster system.

NOTE: Screen Buttons are pressure sensitive.

QUICK START - Saving First Hole Angle Values page 2

fig. 2

fig. 3

PRESS

fig. 1

PRESS

1. POSITION the drill over your first surveyed or marked hole position.

The first hole (combined) angle values, are the template for any repeating holes.

ACTUAL RING and DUMPANGLE VALUES

Locked in RING and DUMPAngle Values in SET column

2. PRESS the DRILL SCREEN button, MAIN MENU (fig. 1).

3. When you are satisfied with the the DUMP & RING values as shown in the ACTUAL Column ... PRESS the SET button (fig. 2). Note: Actual Values for Heading, Ring

and Dump are copied to SET and the SET button turns inactive (fig. 3). Inactive SET button is a fail safe feature to prevent accidental deletion of saved values.See *Activate Set Point

Inactive SET

To *Activate Set Point, refer to full Operators manual.

SAVING TEMPLATE HOLE ANGLE VALUES

fig. 5

QUICK START - DRILLING CONSECUTIVE HOLES page 3

fig. 4

PRESS

4. Move to your next hole. Note: Drill can approach the next hole marker from any direction, or even leave the worksite, return and resume the same drill pattern at a later date with the same angle values as the first hole.

5. Once the mast is in position, PRESS TARGET (fig. 4)

Pressing the Target button retrieves the SET angle values and adjusts the values for the next hole.

Note: The green indicator arrows appear (fig. 4) The green arrows represent the TARGET values and are stationary.

6. Align the Red Indicator Arrows (ACTUAL) over the Green (TARGET) by moving the Ring and Dump of the mast (fig. 5).

If AZIMUTH of the mast has changed while aligning the ACTUAL with the TARGET - PRESS TARGET again (fig. 5). Everytime the TARGET button is pressed, the TARGET is refreshed.

DTI AngleBlasters system checks and adjusts value changes due to movement.

Re-adjust the Masts Ring & Dump to align with TARGET.

NOTE: For a more hands-free feature, activate AUTO TRACK which tracks the TARGET every second, allowing you to more closely monitor the progress of aligning the ACTUAL and TARGET together. Refer to the full version of Operators Manual AUTO TRACK for further details.

7. Once the ACTUAL and TARGET line up you can drill your second hole. Repeat Steps 4, 5, and 6 for any consecutive holes.

AUTO TRACKPress for Hands Freetracking of TARGET.

Green Arrows indicateTARGET values

PRESS

Align Red Arrows (ACTUAL)Over Green Arrows (TARGET)

DRILLING CONSECUTIVE HOLES

MAIN MENU

QUICK START - SCREEN NAVIGATIONAL GUIDE page 4

fig. 2

GAUGE VIEW

DRILL SCREENMAIN MENU

PROJECT SETUP

SELECT APROJECT FILE

NEW PROJECT SETUP

SELECT AN EXISTINGPROJECT SETUP

DRILL SCREEN & GAUGE VIEW

ENTERING OR SELECTING A PROJECT FILE

QUICK START - SCREEN NAVIGATIONAL GUIDE page 5

SYSTEM SETUP & SCREEN PREFENCES

RING AND DUMP VIEW ONLY (DEFAULT)

SYSTEM SETUPMAIN MENU

RING & DUMP (DEFAULT)

MAIN MENU

OFFSET

SCREENPREFERENCES

SCREEN OPTIONS

Use Up and DownScroll Arrows to Selecta Screen Preference

QUICK START - CONTACT page 6

1477 Wellington Ave.Winnipeg, Manitoba, Canada, R3E 0K4

p: (204) 775-2445e: info@dticanada.comw : www.dticanada.com www.dragantechnologies.com

DRAGAN TECHNOLOGIES INC.

For a updated list of our distributors, please visit;www.dragantechnologies.comand follow the Dealers page

Contact UsAt Dragan Technologies Inc. (DTI), we believe in a strong commitment to our customers by providing them with the technical support from our team of engineers and technicians.

Feel free to contact us with your inquires at: