ansoft designer tutorial quarter wave
TRANSCRIPT
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 1/10
Ansoft Designer Tutorial
ECE 584
November 2003
This tutorial will serve as an introduction to the Ansoft Designer Microwave CAD
package by stepping through the first (modified) CAD homework assignment. Pleasenote that there is a link to the Ansoft Designer Student Version download on the ece584home page.
The modified problem is to match a 25 ohm resister to 50 ohm transmission line using a
! wave transformer at 6.0 GHz. (The homework assignment uses different numbers).
Transformer Impedance: 35.35 Ohm
1: Start Ansoft you should get the following window
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 2/10
2: Ansoft starts up with a new project. A circuit design but be inserted:
3: A window will open allowing you to select a substrate for the design. Select the“None” button.
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 3/10
4: A new sub window will open called “Project 1 – Circuit 1 – Schematic”
5: An interface port and a ground must be added to the schematic. Both of these parts areavailable in the draw menu. Select the part from the draw menu an then click inside the
schematic window to add the part.
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 4/10
6: After adding the interface port and ground, the transmission line and resister must beadded. Both of these parts are available under the “Components” tab of the left hand three
pane window. Select the “Resistor” under the “Lumped – Resistors” portion of thecomponent tree. Select the “Transmission Line, Electrical Length” from the “Ideal
Distributed” section of the components tree. Place both parts on the schematic, by
dragging from the tree to the schematic window. Use the ESC key after you’ve placed apart to end the placement of that type of part (otherwise multiple parts may be placed).
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 5/10
7: Connect the various parts by placing a wire between the interface port and thetransmission line, the transmission line and the resistor and the resistor and the ground.
The “Wire” is in the “Draw” menu. Place the wire using the mouse by clicking on thecomponents to be connected.
8: The parameters of the transmission line and resistor must be modified. Right click onthe resistor and select properties. A new window will open. In the “Value” column of the
“R” row type your resistance (in this case 25). Select OK. Right click on the transmission
line and select properties to modify the transmission line. Change the Z value, the Evalue, and the F value. The Z value is the line impedance. The E value is the phase shiftwhich the line should cause (in direct relation to the line length and operating frequency).
The F value is the operating frequency. The completes the drawing of the schematic.
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 6/10
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 7/10
9: Next the analysis of the circuit must be completed. Select “Add Analysis Setup” fromthe “Circuit” menu. A new window will open. We don’t need to change any of the
options so select next. In the sweep variables, highlight F and select the “Edit Button”.
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 8/10
10: Use 3 GHz, 8 GHz, and 10 MHz, for the Start, Stop, and Step frequencies. (Note thisshould be a linear sweep). Click Add and then OK. The Sweep Value
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 9/10
The Sweep / Value entry in the Linear Network Analysis, Frequency Domain shouldchange to LIN 3GHz 8 GHz 10 MHz. Select Finish in the Linear Network Analysis,
Frequency Domain window. You should end up back in the main program window.
11: Select “Analyze” from the “Circuit” menu to analyze the circuit. Note that the
program does not give any feed back that the analysis was completed properly other thana “Project 1 (C:\Program …” entry in the bottom left hand sub window.
12: Select “Create Report” from the “Circuit” menu to plot the response. In the createreport dialog select OK. In the Traces dialog, select Return Loss as the Category,
VSWR1 and the quantity, and dB as the function. Click “Add Trace” to add this plot tothe graph. Then “Done” to plot the graph (See graphics next page). Print both your
schematic and the plot of the VSWR and turn them in with your homework. Save yourproject if you wish. If you have questions e-mail [email protected].
8/18/2019 Ansoft Designer Tutorial Quarter Wave
http://slidepdf.com/reader/full/ansoft-designer-tutorial-quarter-wave 10/10