application flow sizing and order code configuration

Print date: 29.04.2014 11:58 AMApplicator®: 10.16.05 / 133

- 1 / 7 -

Under no circumstances is Endress+Hauser liable for errors, neither in the Software and in its documentation, nor for any errorsand consequential damage which may arise out of their use. The results in Applicator apply to parameters entered by the user. Achange in these parameters could lead to different results. Mandatory data are in the according technical information (TI).

Applicator Sizing - FlowProject : Instruments Add on BMSCustomer: Pepsico C.Project No.: WNV_00234Contact person: Muhammad Sarfraz Phone: +92 332 8449027 Fax: +92 42 35820830

eMail: [email protected]

TAG : LPG-MainTimestamp: --- Review number: ---Sales order number:

Sizing SheetGeneral ParametersFluid Propane (Gas) Ref. Temperature 0 °CState Gas Ref. Pressure 1.013 bar_aCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Dangerous Fluid (Fluid group 1)

Operating Conditionsminimum nominal maximum

Requested Flow 18 780 1 229 Nm3/hPressure 1.2 bar_gTemperature 30 °CDensity 4.0131 kg/m3Viscosity 0.00845 cPZ-factor 0.9649Sound Velocity 248.7 m/sPressure (min/max) 1.2 1.2 bar_gTemp. (min/max) 30 30 °C

Flowmeter : t-mass 65IFlow Principle Thermal (t-mass)Meter Size DN 150Minimum Flow 17.108 Nm3/hCalibrated Flow 1 710.824 Nm3/hMaximum Flow 3 421.65 Nm3/hMaterial (sensor) * SS 1.4404 / 316LProcess connection* G 1 A ISO 228 / 1.4404 /316L ThreadPED category ** : Application meets PED (Art.3.3)

Extended order codeQty Item Description Extended order code

1 Flowmeter t-mass 65I 65I-20AB

1 Accessory Mounting boss - DK6MB DK6MB-B

*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.** The PED category is an Endress+Hauser recommendation and depends on the fluid category, process data as well from the max. permissiblepressure of the selected pressure rating.The fluids of the Applicator data base are classified to 67/548/EWG.

SARFRAZ

Highlight


- 2 / 7 -





Sizing SheetSizing and Calculated Results

minimum nominal maximumRequested Flow 18 780 1 229 Nm3/hPressure loss 9.08E-6 0.01 0.04 mbarVelocity (meas. tube) 0.127 5.52 8.697 m/sMeasured error Mass*** 14.3 1.5 1.5 %Reynolds No. 9 574 414 858 653 668***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

Attention for Flow! Device is used in non-ideal application conditions.

SARFRAZ

Highlight


- 3 / 7 -





Fluid properties sheetFluidFluid name Propane (Gas) State GasChemical formula CH3-CH2-CH3 Calculation standard NEL

Fluid descriptionMedium character CleanFluid group (PED) Dangerous Fluid (Fluid group 1)Fluid stability Stable

Gas mixtureComponent

Fraction

1 Propane (Gas) 100 Mole% 100 Mass%2 0 Mole% 0 Mass%3 0 Mole% 0 Mass%4 0 Mole% 0 Mass%5 0 Mole% 0 Mass%6 0 Mole% 0 Mass%7 0 Mole% 0 Mass%8 0 Mole% 0 Mass%

Basic fluid parametersTc (Critical temperature) 96.69 °CPc (Critical pressure) 42.47 barRho_c (Critical density) 217 kg/m3

Tm (Melting point) -187.7 °CTb (Boiling point) -42.11 °C

Calculated resultsDensity nom. 4.0131 kg/m3Molar mass 44.096 kg/kmolZ-factor nom. 0.9649Viscosity nom. 0.00845 cPSound velocity nom. 248.7 m/sThermal capacity nom. 1.742 kJ/(kg*K)Heat conductivity nom. 0.018 W/(m K)Vapor pressure nom. 10.815 bar_a

Pressure nom. 1.2 bar_gTemperature nom. 30 °C

Reference values: Normal conditions (SI): Standard conditions (US):Atmospheric pressure 1.0132 bar_aDensity normal 2.0122 kg/m3Temperature 0 °CPressure 1.0132 bar_a

Atmospheric pressure 1.0132 bar_aDensity standard 1.9005 kg/m3Temperature 59 °FPressure 14.696 psi_a

SARFRAZ

Highlight


- 4 / 7 -





Installation sheetFlowmeter / Accessories




Installation data :Insertion depth X (scale value) 160.49 mmInsertion tube length 235 mmPipe inner diameter 20°C 158.3 mmDuct Installation HorizontalDuct internal height Duct internal width Wall thickness 5 mmC1 = Height process connection 60 mmC2 = Height sensor connection 46 mmC3 = Height ball valve 0 mmC = Total height of connection 106 mmA= Internal diameter or internal height (duct vertical installation) or internal width (duct horizontal installation)B= Wall thicknessC= Height of connection

*The Enduser is responsible for the correct selection of the piping. Applicator does not calculate necessary pipe wall thickness according to applicationdata. Endress + Hauser takes no liability for the suitability of the pipe dimensions.Attention for Flow! Device is used in non-ideal application conditions.

SARFRAZ

Highlight


- 5 / 7 -





Tri-Size SheetGeneral ParametersFluid Propane (Gas) Ref. Temperature 0 °CState Gas Ref. Pressure 1.013 bar_aCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Dangerous Fluid (Fluid group 1)

Sizing and Calculated ResultsNext Smaller Size Current Size Next Bigger Size

Flow meter t-mass 65I t-mass 65I t-mass 65IFlow Principle Thermal (t-mass) Thermal (t-mass) Thermal (t-mass)Meter Size DN 100 DN 150 DN 200Process connection* G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316LMinimum Flow 7.427 17.108 29.85 Nm3/hCalibrated Flow 742.698 1 710.824 2 985.049 Nm3/hMaximum Flow 1 485.4 3 421.65 5 970.1 Nm3/hPressure loss at req. Flow min. 6.42E-5 9.08E-6 2.49E-6 mbarPressure loss at req. Flow nom. 0.11 0.01 4.14E-3 mbarPressure loss at req. Flow max. 0.27 0.04 0.01 mbarVelocity (meas. tube) at req. Flow min. 0.293 0.127 0.073 m/sVelocity (meas. tube) at req. Flow nom. 12.72 5.52 3.164 m/sVelocity (meas. tube) at req. Flow max. 20.03 8.697 4.985 m/sMeas. error Mass at req. Flow min.*** 6.19 14.3 n.a. %Meas. error Mass at req. Flow nom.*** 1.85 1.5 1.5 %Meas. error Mass at req. Flow max.*** n.a. 1.5 1.5 %Reynolds No. 629 646 414 858 314 070*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 6 / 7 -





Chart SheetFlowmeter : t-mass 65IFlow Principle Thermal (t-mass)Meter Size DN 150Minimum Flow 17.108 Nm3/hCalibrated Flow 1 710.824 Nm3/hMaximum Flow 3 421.65 Nm3/h

***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 7 / 7 -





Corrosion InformationGeneral ParametersFluid Propane (Gas) Abrasivity Not abrasiveState GasCharacter Clean Flow Principle Thermal (t-mass)

Interpretation of Data, (M) Material:A: resistant, 0.05 mm/y (0.002 inches/y)B: insufficient resistant, 0.5 mm/y (0.02 inches/y)C: not resistant, 1.3 mm/y (0.05 inches/y)NR: not recommendedU: unknown

Interpretation of Data, (P) Plastics:A: resistant, 15% vol. Swelling/y; 15% Loss of Tensile Strength/yB: insufficient resistant, 30% vol. Swelling/y; 30% Loss of Tensile Strength/yC: not resistant, 50% vol. Swelling/y; 60% Loss of Tensile Strength/yNR: not recommendedU: unknown

TemperatureMaterial (Sensor) * minimum30°C nominal : 30°C maximum : 30°C(M) CF3M - A 351 A A A(P) EPDM U U U(M) Alloy C22/2.4602 A A A(P) Kalrez A A A(P) PEEK C C C(P) PVDF A A A(M) Stainless steel 316L/316/1.4404 A A A(P) Viton A A A*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.

SARFRAZ

Highlight

Print date: 29.04.2014 12:00 PMApplicator®: 10.16.05 / 133

- 1 / 7 -




TAG : LPG-KHXTimestamp: --- Review number: ---Sales order number:



Requested Flow 18 780 1 229 Nm3/hPressure 1.2 bar_gTemperature 30 °CDensity 4.0131 kg/m3Viscosity 0.00845 cPZ-factor 0.9649Sound Velocity 248.7 m/sPressure (min/max) 1.2 1.2 bar_gTemp. (min/max) 30 30 °C






SARFRAZ

Highlight


- 2 / 7 -






minimum nominal maximumRequested Flow 18 780 1 229 Nm3/hPressure loss 9.08E-6 0.01 0.04 mbarVelocity (meas. tube) 0.127 5.52 8.697 m/sMeasured error Mass*** 14.3 1.5 1.5 %Reynolds No. 9 574 414 858 653 668***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.


SARFRAZ

Highlight


- 3 / 7 -








Fraction








SARFRAZ

Highlight


- 4 / 7 -











SARFRAZ

Highlight


- 5 / 7 -







Flow meter t-mass 65I t-mass 65I t-mass 65IFlow Principle Thermal (t-mass) Thermal (t-mass) Thermal (t-mass)Meter Size DN 100 DN 150 DN 200Process connection* G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316LMinimum Flow 7.427 17.108 29.85 Nm3/hCalibrated Flow 742.698 1 710.824 2 985.049 Nm3/hMaximum Flow 1 485.4 3 421.65 5 970.1 Nm3/hPressure loss at req. Flow min. 6.42E-5 9.08E-6 2.49E-6 mbarPressure loss at req. Flow nom. 0.11 0.01 4.14E-3 mbarPressure loss at req. Flow max. 0.27 0.04 0.01 mbarVelocity (meas. tube) at req. Flow min. 0.293 0.127 0.073 m/sVelocity (meas. tube) at req. Flow nom. 12.72 5.52 3.164 m/sVelocity (meas. tube) at req. Flow max. 20.03 8.697 4.985 m/sMeas. error Mass at req. Flow min.*** 6.19 14.3 n.a. %Meas. error Mass at req. Flow nom.*** 1.85 1.5 1.5 %Meas. error Mass at req. Flow max.*** n.a. 1.5 1.5 %Reynolds No. 629 646 414 858 314 070*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 6 / 7 -







SARFRAZ

Highlight


- 7 / 7 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : LPG-KKTimestamp: --- Review number: ---Sales order number:



Requested Flow 7 80 99 Nm3/hPressure 1.2 bar_gTemperature 30 °CDensity 4.0131 kg/m3Viscosity 0.00845 cPZ-factor 0.9649Sound Velocity 248.7 m/sPressure (min/max) 1.2 1.2 bar_gTemp. (min/max) 30 30 °C

Flowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 40Minimum Flow 1.162 Nm3/hCalibrated Flow 116.23 Nm3/hMaximum Flow 232.46 Nm3/hMaterial (sensor) * SS 1.4404 / 316LProcess connection* PN 40 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application is Cat. II


1 Flowmeter t-mass 65F 65F40-AE**GP


SARFRAZ

Highlight


- 2 / 6 -






minimum nominal maximumRequested Flow 7 80 99 Nm3/hPressure loss 4.21E-3 0.45 0.68 mbarVelocity (meas. tube) 0.855 9.773 12.09 m/sMeasured error Mass*** 2.49 1.5 1.5 %Reynolds No. 15 469 176 787 218 774***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -







Flow meter t-mass 65F t-mass 65F t-mass 65FFlow Principle Thermal (t-mass) Thermal (t-mass) Thermal (t-mass)Meter Size DN 25 DN 40 DN 50Process connection* PN 40 EN 1092-1

B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L

Minimum Flow 0.419 1.162 1.906 Nm3/hCalibrated Flow 41.885 116.23 190.575 Nm3/hMaximum Flow 83.769 232.46 381.151 Nm3/hPressure loss at req. Flow min. 0.02 4.21E-3 1.46E-3 mbarPressure loss at req. Flow nom. 3.71 0.45 0.13 mbarPressure loss at req. Flow max. 5.7 0.68 0.21 mbarVelocity (meas. tube) at req. Flow min. 2.102 0.855 0.513 m/sVelocity (meas. tube) at req. Flow nom. 24.03 9.773 5.861 m/sVelocity (meas. tube) at req. Flow max. 29.73 12.09 7.253 m/sMeas. error Mass at req. Flow min.*** 1.5 2.49 4.08 %Meas. error Mass at req. Flow nom.*** n.a. 1.5 1.5 %Meas. error Mass at req. Flow max.*** n.a. 1.5 1.5 %Reynolds No. 277 185 176 787 136 902*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -





Chart SheetFlowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 40Minimum Flow 1.162 Nm3/hCalibrated Flow 116.23 Nm3/hMaximum Flow 232.46 Nm3/h


SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : LPG-BoilerTimestamp: --- Review number: ---Sales order number:








SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 16 EN 1092-1B1 / 1.4404/316L

Minimum Flow 1.906 4.48 7.853 Nm3/hCalibrated Flow 190.575 448.013 785.338 Nm3/hMaximum Flow 381.151 896.026 1 570.68 Nm3/hPressure loss at req. Flow min. 9.29E-3 1.64E-3 6.5E-4 mbarPressure loss at req. Flow nom. 3.7 0.52 0.18 mbarPressure loss at req. Flow max. 4.21 0.6 0.21 mbarVelocity (meas. tube) at req. Flow min. 1.465 0.594 0.369 m/sVelocity (meas. tube) at req. Flow nom. 30.77 12.46 7.755 m/sVelocity (meas. tube) at req. Flow max. 32.82 13.3 8.272 m/sMeas. error Mass at req. Flow min.*** 1.5 3.36 5.89 %Meas. error Mass at req. Flow nom.*** n.a. 1.5 1.5 %Meas. error Mass at req. Flow max.*** n.a. 1.5 1.5 %Reynolds No. 718 738 457 463 360 836*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -







SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : LPG-CanteenTimestamp: --- Review number: ---Sales order number:








SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L


SARFRAZ

Highlight


- 5 / 6 -







SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : LPG-SchaffTimestamp: --- Review number: ---Sales order number:








SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L


SARFRAZ

Highlight


- 5 / 6 -







SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 7 -




TAG : NG-MainTimestamp: --- Review number: ---Sales order number:

Sizing SheetGeneral ParametersFluid Natural Gas Ref. Temperature 0 °CState Gas Ref. Pressure 1.013 bar_aCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Dangerous Fluid (Fluid group 1)


Requested Flow 50 2 100 2 300 Nm3/hPressure 1.6 bar_gTemperature 30 °CDensity 1.7929 kg/m3Viscosity 0.01146 cPZ-factor 0.9955Sound Velocity 433.5 m/sPressure (min/max) 1.6 1.6 bar_gTemp. (min/max) 30 30 °C






SARFRAZ

Highlight


- 2 / 7 -






minimum nominal maximumRequested Flow 50 2 100 2 300 Nm3/hPressure loss 2.33E-5 0.03 0.04 mbarVelocity (meas. tube) 0.303 12.73 13.94 m/sMeasured error Mass*** 11.2 1.5 1.5 %Reynolds No. 7 504 315 151 345 165***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.


SARFRAZ

Highlight


- 3 / 7 -





Fluid properties sheetFluidFluid name Natural Gas State GasChemical formula NASA-Langley Calculation standard NEL



Fraction

1 Nitrogen (Gas) 2.8 Mole% 4.54 Mass%2 Carbon dioxide (Gas) 0.21 Mole% 0.54 Mass%3 Methane (Gas) 91.82 Mole% 85.5 Mass%4 Ethane (Gas) 4.85 Mole% 8.53 Mass%5 Propane (Gas) 0.26 Mole% 0.68 Mass%6 n-Butane (Gas) 0.06 Mole% 0.21 Mass%7 0 Mole% 0 Mass%8 0 Mole% 0 Mass%

Basic fluid parametersTc (Critical temperature) -77.57 °CPc (Critical pressure) 46.1041 barRho_c (Critical density) 168.8 kg/m3

Tm (Melting point) n.a. °CTb (Boiling point) n.a. °C

Calculated resultsDensity nom. 1.7929 kg/m3Molar mass 17.214 kg/kmolZ-factor nom. 0.9955Viscosity nom. 0.01146 cPSound velocity nom. 433.5 m/sThermal capacity nom. 2.153 kJ/(kg*K)Heat conductivity nom. 0.034 W/(m K)Vapor pressure nom. bar_a




SARFRAZ

Highlight


- 4 / 7 -











SARFRAZ

Highlight


- 5 / 7 -





Tri-Size SheetGeneral ParametersFluid Natural Gas Ref. Temperature 0 °CState Gas Ref. Pressure 1.013 bar_aCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Dangerous Fluid (Fluid group 1)


Flow meter t-mass 65I t-mass 65I t-mass 65IFlow Principle Thermal (t-mass) Thermal (t-mass) Thermal (t-mass)Meter Size DN 100 DN 150 DN 200Process connection* G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316LMinimum Flow 16.156 37.217 64.936 Nm3/hCalibrated Flow 1 615.638 3 721.665 6 493.57 Nm3/hMaximum Flow 3 231.28 7 443.33 12 987.1 Nm3/hPressure loss at req. Flow min. 1.67E-4 2.33E-5 6.6E-6 mbarPressure loss at req. Flow nom. 0.26 0.03 9.66E-3 mbarPressure loss at req. Flow max. 0.31 0.04 0.01 mbarVelocity (meas. tube) at req. Flow min. 0.698 0.303 0.174 m/sVelocity (meas. tube) at req. Flow nom. 29.32 12.73 7.295 m/sVelocity (meas. tube) at req. Flow max. 32.11 13.94 7.99 m/sMeas. error Mass at req. Flow min.*** 4.85 11.2 n.a. %Meas. error Mass at req. Flow nom.*** 3.6 1.5 1.5 %Meas. error Mass at req. Flow max.*** 4.47 1.5 1.5 %Reynolds No. 478 316 315 151 238 586*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 6 / 7 -







SARFRAZ

Highlight


- 7 / 7 -





Corrosion InformationGeneral ParametersFluid Natural Gas Abrasivity Not abrasiveState GasCharacter Clean Flow Principle Thermal (t-mass)



TemperatureMaterial (Sensor) * minimum30°C nominal : 30°C maximum : 30°C*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.

SARFRAZ

Highlight


- 1 / 6 -




TAG : NG-KHXTimestamp: --- Review number: ---Sales order number:



Requested Flow 84 1 050 1 150 Nm3/hPressure 1.6 bar_gTemperature 30 °CDensity 1.7929 kg/m3Viscosity 0.01146 cPZ-factor 0.9955Sound Velocity 433.5 m/sPressure (min/max) 1.6 1.6 bar_gTemp. (min/max) 30 30 °C

Flowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 100Minimum Flow 17.084 Nm3/hCalibrated Flow 1 708.397 Nm3/hMaximum Flow 3 416.79 Nm3/hMaterial (sensor) * SS 1.4404 / 316LProcess connection* PN 16 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application is Cat. II


1 Flowmeter t-mass 65F 65F1H-AB**GP


SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -







Flow meter t-mass 65F t-mass 65FFlow Principle Thermal (t-mass) Thermal (t-mass)Meter Size DN 80 DN 100Process connection* PN 40 EN 1092-1

B1 / 1.4404/316LPN 16 EN 1092-1B1 / 1.4404/316L

Minimum Flow 9.746 17.084 Nm3/hCalibrated Flow 974.591 1 708.397 Nm3/hMaximum Flow 1 949.18 3 416.79 Nm3/hPressure loss at req. Flow min. 9.13E-3 3.6E-3 mbarPressure loss at req. Flow nom. 1.09 0.39 mbarPressure loss at req. Flow max. 1.31 0.47 mbarVelocity (meas. tube) at req. Flow min. 2.135 1.328 m/sVelocity (meas. tube) at req. Flow nom. 26.69 16.61 m/sVelocity (meas. tube) at req. Flow max. 29.23 18.19 m/sMeas. error Mass at req. Flow min.*** 1.74 3.05 %Meas. error Mass at req. Flow nom.*** 2.04 1.5 %Meas. error Mass at req. Flow max.*** 2.76 1.5 %Reynolds No. 322 693 254 533*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -





Chart SheetFlowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 100Minimum Flow 17.084 Nm3/hCalibrated Flow 1 708.397 Nm3/hMaximum Flow 3 416.79 Nm3/h


SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : NG-Gas GensetTimestamp: --- Review number: ---Sales order number:




Flowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 80Minimum Flow 9.746 Nm3/hCalibrated Flow 974.591 Nm3/hMaximum Flow 1 949.18 Nm3/hMaterial (sensor) * SS 1.4404 / 316LProcess connection* PN 40 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application is Cat. II




SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 16 EN 1092-1B1 / 1.4404/316L

Minimum Flow 4.146 9.746 17.084 Nm3/hCalibrated Flow 414.571 974.591 1 708.397 Nm3/hMaximum Flow 829.142 1 949.18 3 416.79 Nm3/hPressure loss at req. Flow min. 0.02 3.68E-3 1.45E-3 mbarPressure loss at req. Flow nom. 2.93 0.42 0.15 mbarPressure loss at req. Flow max. 3.39 0.49 0.18 mbarVelocity (meas. tube) at req. Flow min. 3.137 1.271 0.791 m/sVelocity (meas. tube) at req. Flow nom. 40.79 16.52 10.28 m/sVelocity (meas. tube) at req. Flow max. 43.92 17.79 11.07 m/sMeas. error Mass at req. Flow min.*** 1.5 2.92 5.13 %Meas. error Mass at req. Flow nom.*** n.a. 1.5 1.5 %Meas. error Mass at req. Flow max.*** n.a. 1.5 1.5 %Reynolds No. 313 855 199 763 157 568*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -





Chart SheetFlowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 80Minimum Flow 9.746 Nm3/hCalibrated Flow 974.591 Nm3/hMaximum Flow 1 949.18 Nm3/h


SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : NG-KKTimestamp: --- Review number: ---Sales order number:








SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L

Minimum Flow 2.528 4.146 9.746 Nm3/hCalibrated Flow 252.843 414.571 974.591 Nm3/hMaximum Flow 505.685 829.142 1 949.18 Nm3/hPressure loss at req. Flow min. 8.96E-3 3.11E-3 5.52E-4 mbarPressure loss at req. Flow nom. 1.02 0.31 0.04 mbarPressure loss at req. Flow max. 1.56 0.48 0.06 mbarVelocity (meas. tube) at req. Flow min. 1.779 1.067 0.432 m/sVelocity (meas. tube) at req. Flow nom. 21.97 13.18 5.338 m/sVelocity (meas. tube) at req. Flow max. 27.21 16.31 6.609 m/sMeas. error Mass at req. Flow min.*** 2.23 3.66 8.6 %Meas. error Mass at req. Flow nom.*** 1.5 1.5 1.5 %Meas. error Mass at req. Flow max.*** 1.7 1.5 1.5 %Reynolds No. 130 941 101 399 64 539*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -







SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : NG-BoilerTimestamp: --- Review number: ---Sales order number:




Flowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 80Minimum Flow 9.746 Nm3/hCalibrated Flow 974.591 Nm3/hMaximum Flow 1 949.18 Nm3/hMaterial (sensor) * SS 1.4404 / 316LProcess connection* PN 40 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application is Cat. II




SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 16 EN 1092-1B1 / 1.4404/316L

Minimum Flow 4.146 9.746 17.084 Nm3/hCalibrated Flow 414.571 974.591 1 708.397 Nm3/hMaximum Flow 829.142 1 949.18 3 416.79 Nm3/hPressure loss at req. Flow min. 0.02 3.68E-3 1.45E-3 mbarPressure loss at req. Flow nom. 2.93 0.42 0.15 mbarPressure loss at req. Flow max. 3.39 0.49 0.18 mbarVelocity (meas. tube) at req. Flow min. 3.137 1.271 0.791 m/sVelocity (meas. tube) at req. Flow nom. 40.79 16.52 10.28 m/sVelocity (meas. tube) at req. Flow max. 43.92 17.79 11.07 m/sMeas. error Mass at req. Flow min.*** 1.5 2.92 5.13 %Meas. error Mass at req. Flow nom.*** n.a. 1.5 1.5 %Meas. error Mass at req. Flow max.*** n.a. 1.5 1.5 %Reynolds No. 313 855 199 763 157 568*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -





Chart SheetFlowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 80Minimum Flow 9.746 Nm3/hCalibrated Flow 974.591 Nm3/hMaximum Flow 1 949.18 Nm3/h


SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : NG-CanteenTimestamp: --- Review number: ---Sales order number:




Flowmeter : t-mass 65FFlow Principle Thermal (t-mass)Meter Size DN 25Minimum Flow 0.911 Nm3/hCalibrated Flow 91.114 Nm3/hMaximum Flow 182.229 Nm3/hMaterial (sensor) * SS 1.4404 / 316LProcess connection* PN 40 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application meets PED (Art.3.3)


1 Flowmeter t-mass 65F 65F25-AE**G1


SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L


SARFRAZ

Highlight


- 5 / 6 -







SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 6 -




TAG : NG-SchaffTimestamp: --- Review number: ---Sales order number:








SARFRAZ

Highlight


- 2 / 6 -







SARFRAZ

Highlight


- 3 / 6 -








Fraction








SARFRAZ

Highlight


- 4 / 6 -








B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L

Minimum Flow 2.528 4.146 9.746 Nm3/hCalibrated Flow 252.843 414.571 974.591 Nm3/hMaximum Flow 505.685 829.142 1 949.18 Nm3/hPressure loss at req. Flow min. 8.96E-3 3.11E-3 5.52E-4 mbarPressure loss at req. Flow nom. 1.02 0.31 0.04 mbarPressure loss at req. Flow max. 1.56 0.48 0.06 mbarVelocity (meas. tube) at req. Flow min. 1.779 1.067 0.432 m/sVelocity (meas. tube) at req. Flow nom. 21.97 13.18 5.338 m/sVelocity (meas. tube) at req. Flow max. 27.21 16.31 6.609 m/sMeas. error Mass at req. Flow min.*** 2.23 3.66 8.6 %Meas. error Mass at req. Flow nom.*** 1.5 1.5 1.5 %Meas. error Mass at req. Flow max.*** 1.7 1.5 1.5 %Reynolds No. 130 941 101 399 64 539*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -







SARFRAZ

Highlight


- 6 / 6 -









SARFRAZ

Highlight


- 1 / 7 -




TAG : Compressed AirTimestamp: --- Review number: ---Sales order number:

Sizing SheetGeneral ParametersFluid Air (Gas) Ref. Temperature 0 °CState Gas Ref. Pressure 1.013 bar_aCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Normal Fluid (Fluid group 2)


Requested Flow 105 2 950 3 100 Nm3/hPressure 6 bar_gTemperature 30 °CDensity 8.0688 kg/m3Viscosity 0.01889 cPZ-factor 0.9988Sound Velocity 348.1 m/sPressure (min/max) 6 6 bar_gTemp. (min/max) 30 30 °C






SARFRAZ

Highlight


- 2 / 7 -








SARFRAZ

Highlight


- 3 / 7 -





Fluid properties sheetFluidFluid name Air (Gas) State GasChemical formula Calculation standard NEL

Fluid descriptionMedium character CleanFluid group (PED) Normal Fluid (Fluid group 2)Fluid stability Stable


Fraction

1 Air (Gas) 100 Mole% 100 Mass%2 0 Mole% 0 Mass%3 0 Mole% 0 Mass%4 0 Mole% 0 Mass%5 0 Mole% 0 Mass%6 0 Mole% 0 Mass%7 0 Mole% 0 Mass%8 0 Mole% 0 Mass%

Basic fluid parametersTc (Critical temperature) -140.6 °CPc (Critical pressure) 37.69 barRho_c (Critical density) 324 kg/m3


Calculated resultsDensity nom. 8.0688 kg/m3Molar mass 28.964 kg/kmolZ-factor nom. 0.9988Viscosity nom. 0.01889 cPSound velocity nom. 348.1 m/sThermal capacity nom. 1.015 kJ/(kg*K)Heat conductivity nom. 0.027 W/(m K)Vapor pressure nom. 1 172.5 bar_a

Pressure nom. 6 bar_gTemperature nom. 30 °C



SARFRAZ

Highlight


- 4 / 7 -











SARFRAZ

Highlight


- 5 / 7 -





Tri-Size SheetGeneral ParametersFluid Air (Gas) Ref. Temperature 0 °CState Gas Ref. Pressure 1.013 bar_aCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Normal Fluid (Fluid group 2)


Flow meter t-mass 65I t-mass 65I t-mass 65IFlow Principle Thermal (t-mass) Thermal (t-mass) Thermal (t-mass)Meter Size DN 100 DN 150 DN 200Process connection* G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316L G 1 A ISO 228 / 1.4404 /316LMinimum Flow 26.353 60.706 105.919 Nm3/hCalibrated Flow 2 635.329 6 070.551 10 591.911 Nm3/hMaximum Flow 5 270.66 12 141.1 21 183.8 Nm3/hPressure loss at req. Flow min. 4.05E-4 6.13E-5 1.58E-5 mbarPressure loss at req. Flow nom. 0.32 0.04 0.01 mbarPressure loss at req. Flow max. 0.36 0.05 0.01 mbarVelocity (meas. tube) at req. Flow min. 0.547 0.237 0.136 m/sVelocity (meas. tube) at req. Flow nom. 15.37 6.671 3.824 m/sVelocity (meas. tube) at req. Flow max. 16.15 7.011 4.018 m/sMeas. error Mass at req. Flow min.*** 3.76 8.67 n.a. %Meas. error Mass at req. Flow nom.*** 2.34 1.5 1.5 %Meas. error Mass at req. Flow max.*** 2.73 1.5 1.5 %Reynolds No. 684 582 451 054 341 473*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 6 / 7 -







SARFRAZ

Highlight


- 7 / 7 -





Corrosion InformationGeneral ParametersFluid Air (Gas) Abrasivity Not abrasiveState GasCharacter Clean Flow Principle Thermal (t-mass)



TemperatureMaterial (Sensor) * minimum30°C nominal : 30°C maximum : 30°C(M) CF3M - A 351 A A A(P) EPDM A A A(M) Alloy C22/2.4602 A A A(P) Kalrez A A A(P) PEEK A A A(P) PVDF A A A(M) Stainless steel 316L/316/1.4404 A A A(P) Viton A A A*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.

SARFRAZ

Highlight


- 1 / 6 -




TAG : Boiler SteamTimestamp: --- Review number: ---Sales order number:

Sizing SheetGeneral ParametersFluid Steam, saturatedState Steam SaturatedCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Normal Fluid (Fluid group 2)


Requested Flow 320 4 450 4 600 kg/hPressure 6 bar_gTemperature 165 °CDensity 3.6727 kg/m3Viscosity 0.01451 cPSound Velocity 497.5 m/sPressure (min/max) 6 6 bar_gTemp. (min/max) 165 165 °C

Flowmeter : Prowirl F 200Flow Principle Vortex (Prowirl)Meter Size DN 100Minimum Flow 305.902 kg/hMaximum Flow 11 724.9 kg/hMaterial (sensor) * SS 1.4408 / CF3MProcess connection* PN 16 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application is Cat. I


1 Flowmeter Prowirl F 200 7F2B1H-*******D1S*+PF


SARFRAZ

Highlight


- 2 / 6 -






minimum nominal maximumRequested Flow 320 4 450 4 600 kg/hPressure loss 0.48 94.2 100.66 mbarVelocity (meas. tube) 3.275 45.54 47.08 m/sMeasured error Vol.*** 1 1 1 %Measured error Mass*** 1.7 1.7 1.7 %Reynolds No. 80 411 1 118 213 1 155 906***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.


SARFRAZ

Highlight


- 3 / 6 -





Fluid properties sheetFluidFluid name Steam, saturated State Steam Saturated Calculation standard IAPWS

Fluid descriptionMedium character CleanFluid group (PED) Normal Fluid (Fluid group 2)Fluid stability StableTc (Critical temperature) 401.1 °CPc (Critical pressure) 22.9 bar

Tm (Melting point) 0.04 °CTb (Boiling point) 100 °CKappa 1.29

Calculated resultsDensity nom. 3.6727 kg/m3Viscosity nom. 0.01451 cPSound velocity nom. 497.5 m/sVapor pressure nom. 7.0132 bar_a


Reference values: Normal conditions (SI): Standard conditions (US):Atmospheric pressure 1.0132 bar_a Atmospheric pressure 1.0132 bar_a

SARFRAZ

Highlight


- 4 / 6 -





Tri-Size SheetGeneral ParametersFluid Steam, saturatedState Steam SaturatedCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Normal Fluid (Fluid group 2)


Flow meter Prowirl F 200 Prowirl F 200 Prowirl F 200Flow Principle Vortex (Prowirl) Vortex (Prowirl) Vortex (Prowirl)Meter Size DN 80 DN 100 DN 150Process connection* PN 40 EN 1092-1

B1 / 1.4404/316LPN 16 EN 1092-1B1 / 1.4404/316L

PN 16 EN 1092-1B1 / 1.4404/316L

Minimum Flow 176.593 305.902 695.869 kg/hMaximum Flow 6 768.61 11 724.9 26 671.8 kg/hPressure loss at req. Flow min. 0.9 0.48 0.09 mbarPressure loss at req. Flow nom. 175.22 94.2 18.75 mbarPressure loss at req. Flow max. 187.23 100.66 20.04 mbarVelocity (meas. tube) at req. Flow min. 5.673 3.275 1.44 m/sVelocity (meas. tube) at req. Flow nom. 78.89 45.54 20.02 m/sVelocity (meas. tube) at req. Flow max. 81.55 47.08 20.7 m/sMeas. error Vol. at req. Flow min.*** 1 1 n.a. %Meas. error Vol. at req. Flow nom.*** 2 1 1 %Meas. error Vol. at req. Flow max.*** 2 1 1 %Meas. error Mass at req. Flow min.*** 1.7 1.7 n.a. %Meas. error Mass at req. Flow nom.*** n.a. 1.7 1.7 %Meas. error Mass at req. Flow max.*** n.a. 1.7 1.7 %Reynolds No. 1 471 733 1 118 213 741 399*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -





Chart SheetFlowmeter : Prowirl F 200Flow Principle Vortex (Prowirl)Meter Size DN 100Minimum Flow 305.902 kg/hMaximum Flow 11 724.9 kg/h

***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.Attention for Flow! Device is used in non-ideal application conditions.

SARFRAZ

Highlight


- 6 / 6 -





Corrosion InformationGeneral ParametersFluid Steam, saturated Abrasivity Not abrasiveState Steam SaturatedCharacter Clean Flow Principle Vortex (Prowirl)



TemperatureMaterial (Sensor) * minimum165°C nominal : 165°C maximum : 165°C(M) CF3M - A 351 A A A(M) Graphite A A A(P) Gylon B B B(M) Alloy C22/2.4602 A A A(M) Alloy C22/2.4602/CX2MW A A A(P) Kalrez A A A(M) Stainless steel 316L/1.4435 A A A(M) Stainless steel 316L/316/1.4404 A A A(M) Stainless steel 316Ti/1.4571 A A A(P) Viton NR NR NR*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.

SARFRAZ

Highlight


- 1 / 6 -




TAG : Chiller SteamTimestamp: --- Review number: ---Sales order number:

Sizing SheetGeneral ParametersFluid Steam, saturatedState Steam SaturatedCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Normal Fluid (Fluid group 2)


Requested Flow 50 1 020 1 100 kg/hPressure 6 bar_gTemperature 165 °CDensity 3.6727 kg/m3Viscosity 0.01451 cPSound Velocity 497.5 m/sPressure (min/max) 6 6 bar_gTemp. (min/max) 165 165 °C

Flowmeter : Prowirl F 200Flow Principle Vortex (Prowirl)Meter Size DN 40Minimum Flow 47.194 kg/hMaximum Flow 1 130.56 kg/hMaterial (sensor) * SS 1.4408 / CF3MProcess connection* PN 40 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application is Cat. I


1 Flowmeter Prowirl F 200 7F2B40-*******D2S*+PF


SARFRAZ

Highlight


- 2 / 6 -






minimum nominal maximumRequested Flow 50 1 020 1 100 kg/hPressure loss 0.57 239.55 278.6 mbarVelocity (meas. tube) 3.317 67.67 72.97 m/sMeasured error Vol.*** 1 1 1 %Measured error Mass*** 1.7 1.7 1.7 %Reynolds No. 31 988 652 547 703 727***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.


SARFRAZ

Highlight


- 3 / 6 -





Fluid properties sheetFluidFluid name Steam, saturated State Steam Saturated Calculation standard IAPWS

Fluid descriptionMedium character CleanFluid group (PED) Normal Fluid (Fluid group 2)Fluid stability StableTc (Critical temperature) 401.1 °CPc (Critical pressure) 22.9 bar

Tm (Melting point) 0.04 °CTb (Boiling point) 100 °CKappa 1.29

Calculated resultsDensity nom. 3.6727 kg/m3Viscosity nom. 0.01451 cPSound velocity nom. 497.5 m/sVapor pressure nom. 7.0132 bar_a



SARFRAZ

Highlight


- 4 / 6 -





Tri-Size SheetGeneral ParametersFluid Steam, saturatedState Steam SaturatedCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Normal Fluid (Fluid group 2)


Flow meter Prowirl F 200 Prowirl F 200 Prowirl F 200Flow Principle Vortex (Prowirl) Vortex (Prowirl) Vortex (Prowirl)Meter Size DN 25 DN 40 DN 50Process connection* PN 40 EN 1092-1

B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L

Minimum Flow 19.198 47.194 78.699 kg/hMaximum Flow 459.893 1 130.56 3 016.44 kg/hPressure loss at req. Flow min. 3.05 0.57 0.21 mbarPressure loss at req. Flow nom. 1 271.82 239.55 87.49 mbarPressure loss at req. Flow max. 1 479.14 278.6 101.76 mbarVelocity (meas. tube) at req. Flow min. 8.154 3.317 1.989 m/sVelocity (meas. tube) at req. Flow nom. 166.3 67.67 40.58 m/sVelocity (meas. tube) at req. Flow max. 179.4 72.97 43.76 m/sMeas. error Vol. at req. Flow min.*** 1 1 n.a. %Meas. error Vol. at req. Flow nom.*** n.a. 1 1 %Meas. error Vol. at req. Flow max.*** n.a. 1 1 %Meas. error Mass at req. Flow min.*** 1.7 1.7 n.a. %Meas. error Mass at req. Flow nom.*** n.a. 1.7 1.7 %Meas. error Mass at req. Flow max.*** n.a. 1.7 1.7 %Reynolds No. 1 023 129 652 547 505 326*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -





Chart SheetFlowmeter : Prowirl F 200Flow Principle Vortex (Prowirl)Meter Size DN 40Minimum Flow 47.194 kg/hMaximum Flow 1 130.56 kg/h

***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.Attention for Flow! Device is used in non-ideal application conditions.

SARFRAZ

Highlight


- 6 / 6 -





Corrosion InformationGeneral ParametersFluid Steam, saturated Abrasivity Not abrasiveState Steam SaturatedCharacter Clean Flow Principle Vortex (Prowirl)



TemperatureMaterial (Sensor) * minimum165°C nominal : 165°C maximum : 165°C(M) CF3M - A 351 A A A(M) Graphite A A A(P) Gylon B B B(M) Alloy C22/2.4602 A A A(M) Alloy C22/2.4602/CX2MW A A A(P) Kalrez A A A(M) Stainless steel 316L/1.4435 A A A(M) Stainless steel 316L/316/1.4404 A A A(M) Stainless steel 316Ti/1.4571 A A A(P) Viton NR NR NR*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.

SARFRAZ

Highlight


- 1 / 6 -




TAG : Diesel LineTimestamp: --- Review number: ---Sales order number:

Sizing SheetGeneral ParametersFluid Fuel Oil (light)State LiquidCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Dangerous Fluid (Fluid group 1)


Requested Flow 5 1 750 2 000 kg/hPressure 1.6 bar_gTemperature 45 °CDensity 841.94 kg/m3Viscosity 5.99295 cPSound Velocity 1 250 m/sPressure (min/max) 1.6 1.6 bar_gTemp. (min/max) 45 45 °CVapor Pressure 1.4811E-11 1.4811E-11 1.4811E-11 bar_a

Flowmeter : Promass E 200Flow Principle Coriolis (Promass)Meter Size DN 25Minimum Flow 0 kg/hMaximum Flow 18 000 kg/hMaterial (sensor) * SS 1.4539/904L, ext.temp.Process connection* PN 40 EN 1092-1 B1 / 1.4404/316L FlangePED category ** : Application meets PED (Art.3.3)


1 Flowmeter Promass E 200 8E2B25-******AD2S


SARFRAZ

Highlight


- 2 / 6 -






minimum nominal maximumRequested Flow 5 1 750 2 000 kg/hPressure loss 0.03 69.86 87.57 mbarVelocity (meas. tube) 0.007 2.553 2.917 m/sMeasured error Vol.*** n.a. 0.25 0.25 %Measured error Mass*** n.a. 0.25 0.25 %Reynolds No. 12 4 303 4 918***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 3 / 6 -





Fluid properties sheetFluidFluid name Fuel Oil (light) State LiquidChemical formula Calculation standard Supporting Points

Fluid descriptionSolid content 0 %Medium character CleanAbrasivity Not abrasiveConductivity Not conductiveFluid group (PED) Dangerous Fluid (Fluid group 1)

Basic fluid parametersTc (Critical temperature) 374.1 °CPc (Critical pressure) 221.2 barHeating value 11.833 kWh/Nm3

Tm (Melting point) -20.16 °CTb (Boiling point) 249.8 °C

Temperature / ViscosityTemperature Viscosity 1 15 °C 13.7 cP2 50 °C 5.3 cP

Temperature / DensityTemperature Density 1 15 °C 860 kg/m32 50 °C 839 kg/m3

Temperature / Heat capacityTemperature Thermal capacity 1 10 °C 0 kJ/(kg*K)2 100 °C 0 kJ/(kg*K)

Calculated resultsDensity nom. 841.94 kg/m3Viscosity nom. 5.99295 cPSound velocity nom. 1 250 m/sVapor pressure nom. 1.4811E-11 bar_a



SARFRAZ

Highlight


- 4 / 6 -





Tri-Size SheetGeneral ParametersFluid Fuel Oil (light)State LiquidCharacter Clean Atmospheric Pressure 1.0132 bar_aAbrasivity Not abrasive Standard EN/DIN/ISOFluid Group (PED) Dangerous Fluid (Fluid group 1)


Flow meter Promass E 200 Promass E 200 Promass E 200Flow Principle Coriolis (Promass) Coriolis (Promass) Coriolis (Promass)Meter Size DN 15 DN 25 DN 40Process connection* PN 40 EN 1092-1

B1 / 1.4404/316LPN 40 EN 1092-1B1 / 1.4404/316L

PN 40 EN 1092-1B1 / 1.4404/316L

Minimum Flow 0 0 0 kg/hMaximum Flow 6 500 18 000 45 000 kg/hPressure loss at req. Flow min. 0.11 0.03 9.03E-3 mbarPressure loss at req. Flow nom. 290.08 69.86 15.79 mbarPressure loss at req. Flow max. 364.36 87.57 19.7 mbarVelocity (meas. tube) at req. Flow min. 0.015 0.007 0.003 m/sVelocity (meas. tube) at req. Flow nom. 5.336 2.553 1.187 m/sVelocity (meas. tube) at req. Flow max. 6.098 2.917 1.356 m/sMeas. error Vol. at req. Flow min.*** n.a. n.a. n.a. %Meas. error Vol. at req. Flow nom.*** 0.25 0.25 0.31 %Meas. error Vol. at req. Flow max.*** 0.25 0.25 0.27 %Meas. error Mass at req. Flow min.*** n.a. n.a. n.a. %Meas. error Mass at req. Flow nom.*** 0.25 0.25 0.31 %Meas. error Mass at req. Flow max.*** 0.25 0.25 0.27 %Reynolds No. 6 222 4 303 2 934*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees andassumes no liability for the corrosion resistance of the materials selected here for the application described above.***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information intechnical documentation.

SARFRAZ

Highlight


- 5 / 6 -





Chart SheetFlowmeter : Promass E 200Flow Principle Coriolis (Promass)Meter Size DN 25Minimum Flow 0 kg/hMaximum Flow 18 000 kg/h


SARFRAZ

Highlight


- 6 / 6 -





Corrosion InformationGeneral ParametersFluid Fuel Oil (light) Abrasivity Not abrasiveState LiquidCharacter Clean Flow Principle Coriolis (Promass)




SARFRAZ

Highlight

Endress+Hauser Consult AGKägenstrasse 2CH - 4153 Reinach BL 1

WATT N VOLT18km.Ferozpur Road Lahore, Pakistan

Tell # +92 42 35401829Fax # +92 42 35820830

[email protected]+92 332 8449027

28.04.2014Project name: BMS Add-onProject no.: WNV_00234Cart: Instruments for Pepsico

Pos. Qty. Ordercode

Product

SPKMatNo.

1 1 7F2B1H-B2GCJA3D1SK+AAPFPHZ1 DBI71197720

Prowirl F 200, 7F2B1H, DN100 4"

SPK: DBI[B2] Approval: ATEX II 1/2G Ex ia, II2D Ex tb IIIC[G] Output; Input: PROFIBUS PA, pulse/freq./switch output[C] Display; Operation: SD02 4-line; push buttons +data backup function[J] Housing: GT20 dual compartment, remote,alu coated[A] Electrical connection: Gland M20[3] Sensor Version: Mass flow (integrated temperaturemeasurement)[D1S] Process Connection: PN16, flange EN1092-1-B1 (DIN2501)[K] Calibration Flow: 0.75% volume 3-point[AA] >Operation Language Display: English[PF] >>Accessory Enclosed: Flow conditioner[PH] >>Accessory Enclosed: Cable, remote, 20m[Z1] >>Marking: (50105107)Boiler Steam Tagging (TAG), see additional spec.

Boiler Steam

2 1 7F2B40-B2GCJA3D2SK+AAPFPHZ1 DBI71197717

Prowirl F 200, 7F2B40, DN40 1 1/2"

SPK: DBI[B2] Approval: ATEX II 1/2G Ex ia, II2D Ex tb IIIC[G] Output; Input: PROFIBUS PA, pulse/freq./switch output[C] Display; Operation: SD02 4-line; push buttons +data backup function[J] Housing: GT20 dual compartment, remote,alu coated[A] Electrical connection: Gland M20[3] Sensor Version: Mass flow (integrated temperaturemeasurement)[D2S] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[K] Calibration Flow: 0.75% volume 3-point[AA] >Operation Language Display: English[PF] >>Accessory Enclosed: Flow conditioner[PH] >>Accessory Enclosed: Cable, remote, 20m[Z1] >>Marking: (50105107)Chiller Steam Tagging (TAG), see additional spec.

Chiller Steam

3 1 65F40-AE2AG1HCABBH1 DHA50109563

t-mass 65F40, DN40 1 1/2"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC

Page 1 / 6

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)LPG-KK Tagging (TAG), see additional spec.

LPG-KK


t-mass 65F80, DN80 3"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)LPG-Boiler Tagging (TAG), see additional spec.

LPG-Boiler


t-mass 65F40, DN40 1 1/2"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)LPG-Canteen Tagging (TAG), see additional spec.

LPG-Canteen


t-mass 65F40, DN40 1 1/2"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)LPG-Schaff Tagging (TAG), see additional spec.

LPG-Schaff

Page 2 / 6

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

7 1 65I-20AB1AD1HCABBH1 DHC50109555

t-mass 65I

SPK: DHC[20] Insertion Tube Length: 235 mm 9"[A] Material Insertion Tube; Sensor: Stainl. steel; Stainl. steel[B] Process Connection: G 1 A, thread ISO 228, compressionfitting, Stainl. steel[1] Seal: PEEK, Nitrile, -35...+130oC/-31...+266oF[A] Surface cleaning: Basic version[D] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)NG-Main Tagging (TAG), see additional spec.

NG-Main

8 1 65F1H-AB2AG1HCABBH1 DHA50109566

t-mass 65F1H, DN100 4"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[B] Process Connection: PN16, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)NG-KHX Tagging (TAG), see additional spec.

NG-KHX


t-mass 65F80, DN80 3"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)NG-Gas_Genset Tagging (TAG), see additional spec.

NG-Gas_Genset

10 1 65F50-AE2AG1HCABBH1 DHA50109564

t-mass 65F50, DN50 2"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration

Page 3 / 6

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)NG-KK Tagging (TAG), see additional spec.

NG-KK

11 1 65F80-AE2AG1HCABBH1 DHA50109565

t-mass 65F80, DN80 3"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)NG-Boiler Tagging (TAG), see additional spec.

NG-Boiler

12 1 65F25-AE2AG1HCABBH1 DHA50109562

t-mass 65F25, DN25 1"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)NG-Canteen Tagging (TAG), see additional spec.

NG-Canteen

13 1 65F50-AE2AG1HCABBH1 DHA50109564

t-mass 65F50, DN50 2"

SPK: DHA[A] Material Measuring Tube; Sensor: Stainl. steel; Stainl. steel[E] Process Connection: PN40, flange EN1092-1-B1 (DIN2501)[2] Seal: PEEK, Viton, -20...+100oC/-4...+212oF[A] Surface cleaning: Basic version[G] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)NG-Schaff

Page 4 / 6

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

Tagging (TAG), see additional spec.

NG-Schaff

14 1 65I-20AB1AD1HCABBH1 DHC50109555

t-mass 65I

SPK: DHC[20] Insertion Tube Length: 235 mm 9"[A] Material Insertion Tube; Sensor: Stainl. steel; Stainl. steel[B] Process Connection: G 1 A, thread ISO 228, compressionfitting, Stainl. steel[1] Seal: PEEK, Nitrile, -35...+130oC/-31...+266oF[A] Surface cleaning: Basic version[D] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)Compressed Air Tagging (TAG), see additional spec.

Compressed Air

15 4 DK6MB-B1A DHS50109557

t-mass, mounting boss

SPK: DHS[B] Process Connection: Welding conn., G 1 A female threadISO 228, stainl. steel[1] Additional Test, certificate: Basic version[A] Additional Option: Basic version

65I-Mounting

16 14 DK6CA-4B DHR50109554

t-mass 65, Cable remote version

SPK: DHR[4] Cable, Remote Version: 20 m[B] Approval: ATEX II 1/2GD, ATEX II2GD, TIIS Zone 1

17 1 8E2B25-BGGCCAAD2S1+AAZ1 DDB71108512

Promass E 200, 8E2B25, DN25 1"

SPK: DDB[BG] Approval: ATEX II3G Ex nA[G] Output: PROFIBUS PA, pulse/freq./switch output[C] Display; Operation: SD02 4-line; push buttons +data backup function[C] Housing: GT20 dual compartment, Alu coated[A] Electrical Connection: Gland M20[A] Meas. Tube Mat., Wetted Parts Surface: Stainl. steel, not polished[D2S] Process Connection: PN40, 316L/1.4404, EN1092-1-B1(DIN2501) flange[1] Calibration Flow: 0.25% Mass[AA] >Operation Language Display: English[Z1] >>Marking: (50061469)Diesel Line Tagging (TAG), see additional spec.

Diesel Line

18 1 DK6ST-1HB0 DHS71027709

Plate flow conditioner 19 hole

SPK: DHS[1H] Pipe Diameter: DN100 4"[B] Process Connection: PN16, flange EN1092-1-B1 (DIN2501)[0] Material: 316L/1.4404

19 1 65I-20AB1AD1HCABBH1 DHC50109555

t-mass 65I

SPK: DHC[20] Insertion Tube Length: 235 mm 9"[A] Material Insertion Tube; Sensor: Stainl. steel; Stainl. steel[B] Process Connection: G 1 A, thread ISO 228, compressionfitting, Stainl. steel[1] Seal: PEEK, Nitrile, -35...+130oC/-31...+266oF[A] Surface cleaning: Basic version[D] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC

Page 5 / 6

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

SARFRAZ

Highlight

[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)LPG-Main Tagging (TAG), see additional spec.

LPG-Main

20 1 65I-20AB1AD1HCABBH1 DHC50109555

t-mass 65I

SPK: DHC[20] Insertion Tube Length: 235 mm 9"[A] Material Insertion Tube; Sensor: Stainl. steel; Stainl. steel[B] Process Connection: G 1 A, thread ISO 228, compressionfitting, Stainl. steel[1] Seal: PEEK, Nitrile, -35...+130oC/-31...+266oF[A] Surface cleaning: Basic version[D] Calibration: Factory calibration[1] Additional Test, certificate: Basic version[H] Approval: ATEX II 3G EEx nAC(L) IIC[C] Housing: Wall Alu, IP67 NEMA4X[A] Cable Entry: Gland M20 (EEx d > thread M20)[B] Display; Operation: 20-55VAC / 16-62VDC, 2-line +push buttons[B] Adjustment; Software Feature: Default gas; 1x group.> Additional text: [H] Output, Input: PROFIBUS PA.> Additional text: [1] >>>Marking: (optional): (50061469)LPG-KHX Tagging (TAG), see additional spec.

LPG-KHX

Page 6 / 6

SARFRAZ

Highlight

application flow sizing and order code configuration

Documents

sales order number

applicator data base

endress hauser liable

minimum flow

nm3hmaximum flow

nm3hcalibrated flow

fluid category

review number