No.: 4004E05E

Revision:

Date: December 7, 2004

SPECIFICATIONS PLL405WP-B0X1

APPROVAL FOR SPECIFICATIONS

Name of Company 　

Approved by 　

Signature

Date

Prepared by

Checked by

Checked by

Approved by

Copyright IIYAMA CORPORATION710-1 Kitaowaribe, Nagano-shi 381-0014 JAPAN

【Revision Record】

Rev. Section Contents

Contents

PageChapter1 Precautions ……………… ….……………………………………………… 1-2Chapter2 Application Limit ………………………………………………....………… 3Chapter3 Features ……………………………………… …………………………… 3Chapter4 Electrical Specifications …………………………………………………… 4-5Chapter5 Display Quality ……………………………………………………………… 6-7Chapter6 Controls and Connectors …………………………………………………... 8Chapter7 Connectors …………………………………………………………………. 9-10Chapter8 Reliability and Standards of Quality ………………………………………. 11Chapter9 Appearance, Dimensions and Weight ...…………………………………… 12Chapter10 Accessories ………………………………………………………………… 13Chapter11 Packing Specifications ……………………………………………………... 14Appendix 1 Test Conditions and Measurement Procedures …………………………….. 15-16Appendix 2 Package Drop Test …………………………………………………………. 17Appendix 3 Package Vibration Test ……………………………………………………... 18Appendix 4 LCD Panel Blemishes ……………………………………………………… 19Appendix 5 Case Appearance Inspection Standards ……………………………………. 20-21Appendix 6 Block Diagram ……………………………………………………………... 22 *Labels are attached on the separate sheet.

� Design and specifications are subject to change without notice.� All trademarks used in the specifications are the property of their respective owners

- 4 -

Chapter 1 Precautions1.1 Purpose

This product is designed to use as a data processing device for computer or office automationequipment. (Standard application)Do not use this product for the following purposes require high reliability and safety.- Transporting machine (Ship, aircraft, train, automobile, etc.)- Safety device for disaster prevention or security- Aerospace instrument- Medical device such as life-support system or surgical equipment- Nuclear energy control device or nuclear safety protection system- Communication device for transportation (Operating control system, air-traffic control system)

If you use this product for any other purpose including the above, contact iiyama service center inadvance.

1.2 Product Specifications* This product is designed for indoor use. It is recommended that you read carefully through the

user manual enclosed with this product for your correct use.* All specifications described in this SPECIFICATIONS are applied in only the case of using the

power cable, signal cable or optional parts supplied by iiyama.* The following symptoms are normal with LCD monitors and do not indicate a problem.

(1) Dark spot, bright spotYou may find dark spot or bright spot on the screen.

(2) Afterimage, burn-inAfterimage (burn-in) of the previous screen may remain after switching the image when thesame image is displayed for hours.

(3) Back-light lifeThe fluorescent light used in the LCD monitor may have to be periodically replaced. Youneed to replace the fluorescent light when you find flickering or darkened light.

(4) Characteristic of LCD screenTo protect the LCD panel, do not scratch, rub or push the screen with a hard or sharp object.Do not use tissue paper etc. because these will damage the LCD screen. Do not push theLCD screen surface or frame because it may cause damage such as interference stripes on thescreen.

(5) Stability timeIt takes approx. 20 minutes until internal operation of the electrical components is stabilized.Operate the monitor in 20 minutes after turning ON the power switch.

- 5 -

1.3 Exclusion* Design or use the device incorporates the LCD monitor under the specified power supply. Using

a power supply higher than the rating will cause fire, electric shock, injury or damage. Weassume no responsibility whatsoever for any damages resulting from this case.

* We assume no responsibility whatsoever any damages resulting from fire, earthquake, action bythird person, any accident, user’s deliberation, fault, incorrect use or any other damages underthe inappropriate condition.

* We assume no responsibility whatsoever for any incidental damages such as loss of businessinterests, business interruption, change or vanish of the retention data resulting from normal useor out of use of the monitor.

* We assume no responsibility whatsoever for any damages resulting from malfunction caused byincorrect connection to other equipments.

* We assume no responsibility whatsoever for any damages resulting from use in disregard ofdescription in the enclosed user manual or the SPECIFICATIONS.

1.4 Assurance* We assure of this product on the basis of the guarantee policy described in the user manual.

LCD monitor: 15 months (Used products are not included in the warranty.)Back-light: 15 months(except for aged deterioration caused by lower luminance or burn-in)

* Specifications for LCD panel blemishes are guaranteed for 6 months from the date ofmanufacture.

- 6 -

Chapter 2 Application Limit

This specifications are applied to the followings:

Item 40inch Multimedia LCD monitor with Network-PC

Company SANYO Sales & Marketing Corporation

Model name PLL405WP-B0X1

Chapter 3 Features

◆ 39.6”Wide Screen TFT Color LCD Monitor◆ Supports Resolutions up to 1280×768◆ Super Wide Viewing Angle, High Brightness and High Contrast◆ Integrated PC platform◆ LAN interface connection◆ Operating System: Windows® XP Professional (English)◆ Pivot function is available for portrait screen style mounting

- 7 -

Chapter 4 Electrical Specifications4.1 Display characteristics

(1) LCD PanelDriving system a-Si TFT Active-MatrixPixel structure 1280×768Pixel pitch Horizontal 0.6735mm

Vertical 0.6735mmPixel arrangement RGB vertical stripeEffective screen area Diagonal: 1005mm (39.6”)

Horizontal: 862.080mmVertical: 517.248mm

Brightness 450cd/m2 (Typical)Contrast ratio(All White/All Black) 700:1 (Typical)Viewing angle Left / Right 85°(Typical)

Up / Down 85°(Typical)Display colors 16,777,216

(2) Back lightBack light CCFL×32Life 50,000hours (Typical)

4.2 PC characteristicsProcessor VIA C3 / EDEN EBGA (1GHz)System Clock 266MHzBIOS Award BIOSMemory DDR512 SODIMMGraphic Integrated VIA UniChrome AGPAudio VT1612A,two-ChannelSupported Video Modes 1280×768Storage 40GB 2.5inchOS Windows XP Professional (English)

- 8 -

4.3 Switches Button Soft Off Button Switch AC Power Switch

4.4 Outside connection connector AC Connector AC inlet (3pin plug)

RS232C D-SUB 9pinLAN 10/100 Base T Ethernet : RJ45USB 4pin×2Audio output Speaker Terminal

4.5 Audio output 10W+10W (4Ω,Stereo)

4.6 Input VoltageRating Voltage AC100-230V 50/60HzRating current 2.8-1.3AConsumption electricity 250WInput Voltage AC95-132/198-260V

- 9 -

Chapter 5 Display QualitySee Appendix 1 concerning test conditions and measurement procedures.

Note) Due to the nature of the LCD Screen, an afterimage of the previous screen may remain afterswitching the image, when the same image is displayed for hours. In this case, the screen isrecovered slowly by changing the image or turning off the Power Switch for hours. There isthe possibility that the previous screen has been fixed. Pay attention sufficient when you useLCD Monitor.

5.1 Brightness 350cd/m2 (Min)450cd/m2 (Typical)

5.2 Contrast ratio 500:1 (Min)700:1 (Typical)

5.3 Brightness distribution 1.30 (max)

5.4 Viewable angle Horizontal: left / right: 85 degrees each (Min)Vertical: up / down: 85 degrees each (Min)

5.5 Response time Rise: 14ms (Typical)Fall: 8ms (Typical)

5.6 Screen size & positionResolution 1280 × 768

Horizontal size 862.080± 0.5 Vertical size 517.248± 0.5

Top 1.9 ± 1.2Bottom 1.9 ± 1.2

Left 1.5 ± 1.2

Spacebetweenpicture

and bezel Right 1.5 ± 1.2 (in mm)At resolution of less than 1280×768, displayed text or lines will beirregular in thickness due to screen enlargement process.

5.7 Screen waver Screen must be free from waver. No waver must be detectable at a distance of 70 to 100cm from the face of the LCD screen.

- 10 -

Chapter 6 Controls and Connectors

6.1 Front

① Power Indicator

6.2 Back

② Handles③ USB Connector④ RS-232C Connector⑤ LAN Connector⑥ Soft Off Button⑦ Brightness knob⑧ Volume knob⑨ External Speaker Output Terminal⑩ AC Connector⑪ Main Power Switch

6.3 Factory settings Back Main Power Switch: OFF

- 11 -

Chapter 7 Connectors

7.1 Input signal Connectors

(1) 10/100 base T Ethernet

PIN Signal PIN Signal PIN Signal

1 Transmit + 4 NC 7 NC

2 Transmit - 5 NC 8 NC

3 Receive + 6 Receive -

(2) RS-232C 9pin connector

PIN Signal PIN Signal PIN Signal

1 NC 4 DTR (Data Terminal Ready) 7 RTS (Request To Send)

2 RxD (Receive Data) 5 Ground 8 CTS (Clear To Send)

3 TxD (Transmit Data) 6 DSR (Data Set Ready) 9 NC

aJpr_

N O P Q R

S T U V

- 12 -

(3) USB 4pin connector (Connector shape: series A)

PIN Signal

1 VDD

2 Data -

3 Data +

4 Ground

7.2 AC Connector 3-pin plug

7.3 Output Audio terminal Speaker terminal

- 13 -

Chapter 8 Reliability and Standardsof Quality

8.1 External environmental conditions(1) Temperature: During operation: 0-35°C

During storage/transport: –20-60°C(2) Humidity: During operation: 30-80% (no condensation)

During storage/transport: 10-80% (no condensation)(3) Altitude limitations: During operation: Not more than 3,000m

During storage/transport: Not more than 12,000m

8.2 Insulation resistance DC500V 10M� (min)

8.3 Insulation dielectric strength AC 1,500V for 1 minute (Current sensitivity: 20mA max)

8.4 Leakage current 1mA (max) at AC120/230VInput Voltage Leakage current

AC120/230V Not more than 1mAAC100V Not more than 0.4mA

8.5 Instantaneous power-outage test No abnormality when power is interrupted (AC 95 to 0V)

for an interval of 1.5 cycles at 50Hz. 8.6 Power surge No abnormal operation following application of 1kV with

pulse duration of 50ns to 1μ on the AC line.No damage from 2kV.

8.7 Rush current 35A0-p (max) Duration within 2 cycles at 25°C, AC 100V, 60Hz45A0-p (max) Duration within 2 cycles at 25°C, AC 200V, 50Hz

8.8 Electrostatic destruction No destruction from air discharge of ±15kV.StrengthStrengthStrengthStrength No abnormal operation from contact discharge of ±4kV.

Testing conducted using capacitor discharge method(150pF+330�).

8.9 Approvals

(1) Safety: CEUL 60950 Third EditionCSA C22.2 No. 950

(2) EMC: CEFCC Class A

8.10 Drop test 50~25cm (2corner, 2edges, 3faces)(in package) Note: See Appendix 2 concerning package drop test.

8.11 Vibration test Sinusoidal wave vibration.(in package) Vibration: 13.3Hz

Amplitude: 3mm Directions: Top and bottom direction Time: 60 minutes

Rope credit being anonymous Note: See Appendix 3 concerning package vibration test.

- 14 -

Chapter 9 Appearance, Dimensions andWeight

9.1 Appearance Exterior color: BlackDepth: 145mmWidth: 951mmHeight: 607mmWeight: Net: 32kg

Gross: 42kg

9.2 Enclosure material Front cabinet: ABSBack cover: AL

9.3 Labeling Rating label: On the rear of back coverSerial no. label: In specified position on carton(See Chapter 11)

USRããLPQKN?

VRNããLPTKQ?NQRããLRKT?

- 15 -

Chapter 10 AccessoriesSee Chapter 11 concerning packaging of accessories.

• Power Cable : 3.8m, black Rating: 7A,125V (North America) 3.8m, black Rating; 10A,250V (Europe, Australia)• Instruction Manual (English)• Recovery CD-ROM• Sample: Pivot software / VIA Driver (CD)

- 16 -

Chapter 12 Packaging Specifications

PARTS-BOX・ Power Cable ・Instruction Manual

・ Recovery CD-ROM・ Sample: Pivot software / VIA Driver (CD)

PACKING-CASE

CUSHION

PARTS-BOXPACKING-SHEET TAPE

SHEET

Fold up PACKING-SHEET. PAD

CUSHION

CUSHION

PAD

CARTON-TAPEAffixed in H-configuration attop and bottom face.

LABEL SERIAL-LABEL

* See another page for the position of labels.

① ②

③ ④

⑤⑥

⑦ ⑧

CARTON-TAPEAffixed inI-configuration attop and bottom face.

- 17 -

Appendix 1 Test Conditions and Measurement Procedures1-1 Standard test conditions

Unless specifically indicated otherwise, measurements are taken under the following conditions.This excludes correlative measurements.Temperature: Normal room temperature (17-25°C)Humidity: 30-70%AC input voltage: 120±2V, 60HzBrightness: CenterContrast CenterWarm-up time: 30 minutes or more after power turned on at normal room

temperature.Resolution: 1280 × 768Signal pattern: All-white (Effective screen area )Measurement point: Screen centerMeasuring instrument: Topcon luminance colorimeter BM-5A or equivalent

Note: All the measurements taken by this instrument should beperformed at a distance of 30cm in a dark room orequivalent condition. It must not touch the LCD surface.

(Measuring field: 1°, Viewing angle: ��= 0°, ø = 0° )

1-2 Contrast ratio Signal pattern: All-white, All-backFormula: Brightness of white screen

Brightness of black screen1-3 Brightness distribution Measurement points: Five specified points A-E

Formula: Maximum brightness Minimum brightness

Pixel77

384

690

A

B

C

E

D

128 640 1152Pixel

- 18 -

1-4 Viewable angle

Signal pattern: All-white, All-black Requirement: Contrast ratio > 10

Right Ø RHorizontal Left Ø LUp ��UVertical Down ��D

1-5 Response timeSignal pattern: All-white, All-black

Tr = Rise (Black, White) Tf = Fall (White, Black)

1-6 Screen size & positionResolution: 1280 × 768Measurement points:

Horizontal size xVertical size y

Top aBottom bLeft c

Spacebetweenpictureand bezel Right d

Measuring instrument: Scale

Tf Tr

White Black White

0%

100%90%

10%

6 o’clock direction

��UØL

��D

Center

ØR

a

y

bBezel

Picture

c x d

- 19 -

Appendix 2 Package Drop Test2-1 Purpose The purpose of this test is to evaluate whether packaging is sufficient to protect the LCD monitor

against shock resulting from accidental drop page during transport.

2-2 Evaluation standard1. Prior to package drop test(1) Visual inspection

Check that parts and case are free of contact, friction, deformation and scratches.(Pay particular attention to circuit boards and sheet metals.)

(2) Inspection of functions and performance • Ensure that product meets functional and performance standards in all respects. • Ensure that no screws are loose.2. After package drop test(1) Visual inspection

Check that parts and case are free of contact, friction, deformation and scratches.(Pay particular attention to circuit boards and sheet metals.)

(2) Inspection of functions and performance • Ensure that product meets functional and performance standards in all respects. • Ensure that no screws are loose.

2-3 Test procedure1. Perform the checks as described in section 2-2 Evaluation standard, both before and after

package drop test.2. Environmental consideration: Normal room temperature (17-25°C) and humidity (30-70%)3. Conduct the drop test in the sequence below. (Regarding bottom face of product as FRONT face.)

Drop pointsDrop sequence A B C D

Dropdistance(㎝)

1 Corner 2-3-6 3-4-5 2-3-5 3-4-6 402 Corner 1-2-6 1-4-5 1-2-5 1-4-6 403 Edge 2-3 4-3 3-5 3-6 404 Edge 1-2 1-4 1-5 1-6 405 Face 3 3 3 3 256 Face 2 4 5 6 507 Face 6 5 4 2 50

4. Drop method Spontaneous drop5. Drop face Drop face should be a horizontal surface of a hard object such as

stone, concrete, etc. The face should not be dented during the test.

3

5

2

6

41

- 20 -

Appendix 3 Package Vibration Test3-1 Purpose

The purpose of this test is to evaluate whether the packaging adequately protects appearance,functions and performance of the product against vibration encountered during transport.

3-2 Test procedure1. Perform the checks as described in Appendix 2 Package Drop Test, section 2-2 Evaluation

standard, 1. Prior to package drop test.2. Attach the product to the vibration test stand , and set the test conditions. (Environmental consideration: Normal room temperature and humidity.)3. Perform the test.4. After applying vibration, perform the checks as described in Appendix 2 Package Drop Test,

section 2-2 Evaluation standard, 2. After package drop test.

- 21 -

Appendix 4 LCD Panel Blemishes4-1 Test conditions

1. The test should be performed under the normal operation.

2. The panel should be viewed at a minimum distance of 50-70cm. (Front view: � = 0°)3. Ambient light level at the panel surface should be 300-700 lux.4. Bright spot test should be performed at black screen and dark spot test should be performed at

each Red, Green and Blue screen.

4-2 Quality zone: Effective screen area

4-3 Limit of screen blemishes

※ Total of Bright Spot and Dark spot should be 13 or less.※ The separation between bright spot and bright spot /dark spot and dark spot should be 15mm or

less.

4-4 Other defects None of the following defects is allowed. Evaluation standard:

1. The picture is not correctly displayed when receiving signals below.(A) All-white(B) All-black(C) Every other line white and black

2. Vertical line missing3. Horizontal line missing <Example>4. Cross line missing5. Newton rings

condition specificationHigh bright random ≦3Two-connected high bright spot ≦1Three-connected high bright spot ≦0

Bright spot

Low bright spot ≦8Random ≦10Two-connected ≦5

Dark spot

Three-connected ≦0

- 22 -

Appendix 5 Case Appearance Inspection Standards5-1 Case class specifications

5-2 Scratches, blemishes and other foreign matter

Clear scratches, blemishes andother foreign matter

Unclear scratches, blemishes andother foreign matterSurface class Defect size (mm2) Number allowed

per sizeTotal numberallowed

Number allowedper size

Total numberallowed

X </= 0.3 4 50.3 < X </= 0.5 3 4 0.5 < X </= 0.7 None permitted 31

0.7 < X None permitted

4

None permitted

5

X </= 0.5 5 60.5 < X </= 0.7 3 40.7 < X </= 1.0 None permitted 2

2

1.0 < X None permitted

5

None permitted

6

X </= 1.0 5 41.0 < X </= 1.5 4 21.5 < X </= 2.0 2 1

3

2.0 < X None permitted

6

None permitted

7

Notes 1: Although no specific standards are established for other faces, any part with defects thatmight detract from the appearance of the product shall not be used.

2: Defects are measured by a measurement diagram of apparent defects.3: Distance between defects should be 200mm or more.4: Spot and welding department should not be uneven remarkably in surface class 3.

- 23 -

5-3 Edge gaps, edge alignment, burrs, etc.Item Surface class 1 Surface class 2 Surface class 3

Edge gaps (difference in space between edges) 0.5mm max 0.5mm max 1.5mm maxEdge alignment 0.5mm max 0.5mm max 1.5mm maxBurr height 0.4mm max 0.5mm max 0.6mm max

5-4 StainsStains that can be removed by wiping shall in principle be permitted. However, stains that mightdetract from the appearance of the product shall be unacceptable. Stains un-removable areregarded as scratches and apply to Clause 5-2.

5-5 Gap between LCD surface and bezelThe gap between LCD surface and bezel shall be not more than 3.5mm.

- 24 -

Appendix 6 Block Diagram Block diagram

Back-lightUnit

AC Power Switch

POWER SUPPLYPONRelay

Soft OffButton

RS232C

RAM

SO-DIMM

RJ45TFT (WXGA)LCD PANELLAN PHY

USB x 2

HDD

LVDS Transmitter

BIOS ROM

AudoiVR

AudioAmplifier

CPUVIA C3

BrightnessVR

South Bridge

VT8235

North Bridge

VIA CLE266

FAN

- 25 -

Appendix 8 Labels

Rating Plate

Case Label