Please read and save these instructions.Read carefully before attempting to assemble,install,operate or maintain the product describedprotect yourself and others by observing all safety information, Failure to comply with instructions could result in personal injury andlorproperty damage Retain instructions for future reference.

1

DescriptionDescriptionDescription

The Arbor Presses are designed for riveting, squeezing, bending, punching,flattening, removing a bearing or pressing in bearings. Removable, rotating,machined anvil has 4-slots to provide convenient support for workpieces thatvary in size and shape.Presses are Suited for work in production lines as wellas in machine shops, automotive repair shops and home workshops.805-10055 is a 1/2-ton press, 805-10205 is a 2-ton press, 805-10305 is a 3-tonpress, 805-10405 is a 4-ton press,and 805-10105 is a 1-ton press.

General Safety InformationGeneral Safety InformationGeneral Safety Information

1. For best operation, the arbor pressmust be bolted to a stationaryobject that is also affixed to thefloor.

2. When using the press, be sure thework is mounted securely in it. Donot attempt to use the press withthe workpiece mounted on an angle.

3. Use only accessories designed forthe arbor press. Attachments andequipment used in the pressingoperation must be as strong as thepress.Use steel collars and blocksto press against the workpiece.

4. Do not overload the press by usinghandle extensions (cheater bars).

5. When not in use, the ram should bein the down position to preventaccidents.

6. Know the arbor press and acces-sories. Read and understand owner'smanual.

7. Wear a face shield or safety glasses.

8. Never place hands in jeopardy.

9. Always check your set up, i.e., seethat the ram contacts workpiecesquarely before applying pressure.

10. Keep mind on work. Be alert.

11. Make sure workpiece, punch, anviland accessories are securelyclamped.

AssemblyAssemblyAssembly

1/2t,2t,3t,4t perss ,Refer to Figure 1.l. Mount arbor press to bench or stand,

Secure arbor press using two mount-ing holes on the body (Ref. No. 1).(Hardware is not supplied.)

2. The l/2 and 2-Ton presses are cam-pletely assembled. The handle needsto be installed on the 3 and 4-Tonpresses.To install handle, remove capand bolt from handle (Ref. Nos. 4, 5and 7). Insert handle into pinion(Ref. No. 3) and replace cap and bolt.secure handle in position with knob(Ref. No. 6).

3. To use with a punch, remove pinionretaining ring and set screw (Ref.Nos. 9 and 10) from pinion. Removepinion from the body. Remove ram(Ref, No. 2), mount ram upside downso the punch hole is facing down.Replace pinion, pinion retaining ringand set screw.lnsert the punch (Ref.No. 17) best suited to the job.Magnet inside ram will secure punchin position. Set screws (Ref. No. 11)will ease or restrict the ram action.Adjust to your requirements.

1t perss Refer to Figure 2.1. Mount arbor press to bench or

stand. Secure arbor press usingtwo mount- ing holes on thebody (Ref. No. 1).(Hardware is not supplied.)

2.To use with a punch remove setscrew, handwheel and key (Ref.Nos.17, 16 and 8) from pinion(Ref. No. 3). Remove pinion fromthe body.Remove ram (Ref. No. 2), mount ramupside down so the punch hole isfacing down. Replace pinion, key,handwheel and set screw. Insertthe punch (Ref. No. 19) best suitedto the job. Make sure that magneticinsert is holding the punch.

3. To adjust the ram action to yourrequirements, use set screws (Ref.No. 13). All set screws should betightened with the same amount ofpressure. Secure set screws by tight-ening nuts (Ref. No. 12).

4. To use handwheel for light press-work, remove bolt (Ref. No. 4), cap(Ref. No. 5) and arm-handle(Ref. No. 7) from pinion.

MaintenanceMaintenanceMaintenance

1. Oil the pinion periodically throughthe oil fitting, and grease the ramrack whenever necessary. Keep alight film of oil on machined surfaceto prevent rust. Keep work areaclean. Clean the arbor press of dirtand debris after every use.

2. If the ram is loose and drops by itself,loosen hex nuts and tighten screws(Ref. Nos. 11 and 12) for adjustment.All screws should be tightened withthe same amount of pressure. Secureset screws by tightening nuts.

ArborArborArbor PressesPressesPresses

-Part description and number as shown in parts list

Figure1 Repair Parts illustration for Arbor Presses

Repair Parts List for Arbor Presses

1 Body ＋ ＋ ＋ ＋ 12 Ram with Magnet ＋ ＋ ＋ ＋ 13 Pinion TT728702.OOJG TT28715.OOJG TT28728,OOJG TT28739.OOJG 14 6-1.0 x 16mm Socket Head Bolt * － － － 24 6-1.0 x 20mm Socket Head Bolt － * * * 2

5 Cap ＋ ＋ ＋ ＋ 26 Knob TT28704.OOJG TT28717.OOJG TT28730.OOJG TT28730,OOJG 17 Handle TT28705.OOJG TT28718.OOJG TT28731.OOJG TT28740.OOJG 18 OiI Fitting ＋ ＋ ＋ ＋ 29 Pinion Retaining Ring ＋ ＋ ＋ + 210 8-1.25 x 8mm Set Screw * * * * 111 6-1.0 x 20mm Set Screw * － － － 411 8-1.25 x 25mm Set Screw － * * * 412 6-1.0mm Hex Nut * － － － 412 6-1.25mm Hex Nut － * * * 4

13 TabIe Pin ＋ ＋ ＋ ＋ 114 Anvil ＋ ＋ ＋ ＋ 115 6-1.0x25mm Hex Head Bolt * － － － 415 8-1.25 x 30mm Hex Head Bolt － * － － 415 8-1.25 x 20mm Socket Head Bolt － － * * 4

16 Face Plate ＋ ＋ ＋ ＋ 117 Punch 5et(3pleces:round,point,square) TT28711.OOJG TT28722.OOJG TT28722.OOJG TT28722.OOJG 1

( * ) Standard hardware item available localty(＋) Parts not available for sales.

2

-Part description and number as shown in parts list

Figuer2 Repair Parts illustration for Arbor Presses

Repair Parts List for Arbor Press

1 Body + 12 Ram with Magnet + 13 Pinion TT 28804.00 JG 14 6-1.0 x 25mm Socket Head Bolt * 25 Cap + 26 Knob + 17 Arm-handle TT 28807.00 JG 18 6x 6 x 16mm Key + 19 Table pin + 110 Anvil + 111 6-1.0 x 25mm Hex head bolt * 412 6-1.0nm Hex nut * 413 6-1.0 x 20mm Set screw * 414 Face plate + 115 Oil fitting + 216 Handwheel + 117 8-1.25 x 8mm Set screw * 118 Handle + 119 Punch set (3 pieces: round, point, square) TT 28722.00 JG 1

( * ) Standard hardware item available localty(＋) Parts not available for sales.

3