arcat | free building product cad details, bim, …€¦ · web viewfinish: deep colors and accent...

SECTION 09 90 00 - Painting and CoatingPAINTS AND COATINGS

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Surface preparation and field painting of exposed exterior items and surfaces.

1.1.2 Surface preparation and field painting of exposed interior items and surfaces.

1.1.3 Surface preparation and field painting/sealing of Specialty Surfaces that do not have factory-applied final finish.

1.2 RELATED SECTIONS

1.2.1 Section 05 50 00 - Metal Fabrications.

1.2.2 Section 06 20 00 - Finish Carpentry.

1.2.3 Section 07 10 00 - Dampproofing and Waterproofing.

1.3 REFERENCES

1.3.1 ANSI A13.1 - Scheme for the Identification of Piping Systems.

1.3.2 ANSI Z535.1 - Safety Color Code.

1.3.3 ASTM D 16 - Standard Terminology Relating to Paint, Varnish, Lacquer, and Related Products.

1.3.4 ASTM D 3359 - Standard Test Methods for Measuring Adhesion by Tape Test.

1.3.5 ASTM D 1653 - Standard Test Methods for Water Vapor Transmission of Organic Coating Films.

1.3.6 ASTM E-96 - Standard Test Methods for Water Vapor Transmission of Materials.

1.3.7 ASTM D 412 - Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension.

1.3.8 40 CFR 59, Subpart D National Volatile Organic Compound Emission Standards for Architectural Coatings.

1.3.9 Fed Spec - TT C-555B - Wind Driven Rain Test.

1.3.10 SSPC, The Society for Protective Coatings - Web Site http:www.sspc.org:1.3.10.1 SSPC-SP1 Solvent Cleaning.1.3.10.2 SSPC-SP2 Hand Tool Cleaning.1.3.10.3 SSPC-SP3 Power Tool Cleaning.

09 90 00-1

1.3.10.4 SSPC-SP6 Commercial Blast Cleaning.1.3.10.5 SSPC-SP7 Brush-Off Blast Cleaning.

1.3.11 PDCA Paint and Decorating Contractors of America - Web Site http://www.pdca.org:1.3.11.1 PDCA Standards P1 through P15

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements

1.4.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.4.2.1 Preparation instructions and recommendations.1.4.2.2 Storage and handling requirements and recommendations.1.4.2.3 Installation methods.

1.4.3 Finish Schedule: Submit finish schedule including color information, gloss and model number for each type and color of finish specified.

1.4.4 Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: All primary products specified in this section will be supplied by a single manufacturer with a minimum of ten years experience.

1.5.2 Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five years demonstrated experience in installing finishes and coatings of the same type and scope as specified.

1.5.3 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1.5.3.1 Finish areas designated by Architect.1.5.3.2 Do not proceed with remaining work until workmanship, color, and sheen are

approved by Architect.1.5.3.3 Refinish mock-up area as required to produce acceptable work.

1.6 DELIVERY, STORAGE, AND HANDLING

1.6.1 Store products in manufacturer's unopened packaging until ready for installation.

1.6.2 Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.

1.6.3 Take special safety precautions against hazards from toxic and flammable materials.

1.6.4 Place paint and solvent contaminated cloths and materials, subject to spontaneous combustion, in containers and remove from job site each day.

1.6.5 Keep open flame, electrical and static spark, and other ignition sources from flammable vapors and materials at all times.

1.7 PROJECT CONDITIONS

1.7.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

09 90 00-2

1.7.2 Post "WET PAINT" signs during application and curing of all coatings that may be accessed by other trades or the public.

1.7.3 Post "NO SMOKING" signs during application and curing of solvent-based materials.

1.8 COORDINATION

1.8.1 Coordinate Work with other operations and installation of finish materials to avoid damage to installed materials.

1.8.2 Do not apply coating materials until moisture or dust-producing work or other appearance or performance impairing construction activities have been completed.

1.9 WARRANTY

1.9.1 At project closeout, provide to Owner or Owners Representative an executed copy of the manufacturer's standard limited warranty against manufacturing defect, outlining its terms, conditions, and exclusions from coverage.

1.10 EXTRA MATERIALS

1.10.1 At project closeout, provide to the owner or owners representative, two gallons (7.75L) of each finish coating material in sealed 1 gallon (3.875 L) containers, clearly marked with color and finish identification.

1.10.2 Custom Colors: Provide a list of color formula and location for each finish specified.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Rodda Paint, which is located at: 6107 N. Marine Dr.; Portland, OR 97203; Toll Free Tel: 800-452-2315; Tel: 503-737-6033; Fax: 503-737-6004; Email:request info ([email protected]); Web:www.roddapaint.com2.1.1.1 Architectural Representative: Jeff McIntyre: Phone: (206) 396-7074. E-mail:

[email protected] Seattle Sales Office: 3838 Fourth Ave. South, Seattle, WA 98134. Phone: (206)

652-0445. Fax: (206) 652-0565.

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of 01 60 00 - Product Requirements.

2.2 PAINT MATERlALS - GENERAL

2.2.1 VOC : Provide materials to meet EPA 40 CFR Part 59 (AD-FRL-6149-71] RIN 2060 - National Volatile Organic Compound Emission Standards for Architectural Coatings, Final Rule, Federal Register / Vol. 63, No.176, September 11, 1998/Rules and Regulations.

2.2.2 LEED v3.0 NC, CI, or CS IEQ 4.2: Low-Emitting Materials - Paints and Coatings Compliance2.2.2.1 Paints and coatings used on the interior of the building (i.e., inside of the

weatherproofing system and applied onsite) shall comply with the following criteria as applicable to the project :

2.2.2.1.1 Architectural paints and coatings applied to interior walls and ceilings shall not exceed the volatile organic compound (VOC) content limits established in Green Seal Standard GS-11, Paints, 1st Edition, May 20, 1993.

2.2.2.1.1.1 Flats: 50 g/L.

09 90 00-3

2.2.2.1.1.2 Non-Flats: 150 g/L.2.2.2.1.2 Anti-corrosive and anti-rust paints applied to interior ferrous metal

substrates shall not exceed the VOC content limit of 250 g/L established in Green Seal Standard GC-03, Anti-Corrosive Paints, 2nd Edition, January 7, 1997.

2.2.2.1.3 Clear wood finishes, floor coatings, stains, primers, and shellacs applied to interior elements shall not exceed the VOC content limits established in South Coast Air Quality Management District (SCAQMD) Rule 1113, Architectural Coatings, rules in effect on January 1, 2004.

2.3 EXTERIOR PAINT SYSTEMS

2.3.1 Exterior Metal:2.3.1.1 Substrate: Ferrous Metal Structural Steel.

2.3.1.1.1 Primer: Ferrous Metal Surfaces - Prime exposed metal areas with one coat 708225 Barrier III High Solids Alkyd Metal Primer. (solvent based)

2.3.1.1.2 Primer: Ferrous Metal Surfaces - Prime exposed metal areas with one coat 508901 Metal Master Primer (Waterborne).

2.3.1.1.3 Finish: Gloss, Silicone Alkyd Gloss - Two coats Rodda 758801 Powerkote Silicone Alkyd Enamel.

2.3.1.1.4 Finish: Semi-Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM Self Crosslinking Semi-Gloss Enamel.

2.3.1.1.5 Finish: Satin, Acrylic - Two coats Rodda 528901 Multi Master DTM Self Crosslinking Satin Enamel.

2.3.1.1.6 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Acrylic Enamel Gloss.

2.3.1.1.7 Finish: Semi-Gloss Acrylic -Two coats Rodda 542001 Unique II Interior/ Exterior Semi-Gloss.

2.3.1.1.8 Finish: Low Gloss Acrylic -Two coats Rodda 532001 Unique II Interior/ Exterior Low Gloss.

2.3.1.1.9 Finish: Low-Gloss Acrylic -Deep Colors and Accent Striping: Two coats Rodda 53203x Color Base System Exterior.

2.3.1.1.10 Finish: Gloss, Alkyd Gloss - Two coats Rodda 758101 All Purpose Equipment Enamel.

2.3.1.1.11 Finish: Semi-Gloss, Alkyd Semi-Gloss - Two coats Rodda 745001 Porsalite Semi-Gloss.

2.3.1.2 Substrate: Ferrous Metal: Windows, Frames, and Doors2.3.1.2.1 Primer: Ferrous Metal Surfaces - Prime exposed metal areas with one coat

708225 Barrier III High Solids Alkyd Metal Primer. (solvent based)2.3.1.2.2 Primer: Ferrous Metal Surfaces - Prime exposed metal areas with one coat

508901 Metal Master Primer (Waterborne).2.3.1.2.3 Finish: Gloss, Silicone Alkyd Gloss - Two coats Rodda 758801 Powerkote

Silicone Alkyd Enamel.2.3.1.2.4 Finish: Semi-Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM

Self Crosslinking Semi-Gloss Enamel.2.3.1.2.5 Finish: Satin, Acrylic - Two coats Rodda 528901 Multi Master DTM Self

Crosslinking Satin Enamel.2.3.1.2.6 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Acrylic Enamel

Gloss.2.3.1.2.7 Finish: Semi-Gloss Acrylic -Two coats Rodda 542001 Unique II Interior/

Exterior Semi-Gloss.2.3.1.2.8 Finish: Low Gloss Acrylic -Two coats Rodda 532001 Unique II Interior/

Exterior Low Gloss.2.3.1.2.9 Finish: Low-Gloss Acrylic -Deep Colors and Accent Striping: Two coats

Rodda 53203x Color Base System Exterior.2.3.1.2.10 Finish: Gloss, Alkyd Gloss - Two coats Rodda 758101 All Purpose

09 90 00-4

Equipment Enamel.2.3.1.2.11 Finish: Semi-Gloss, Alkyd Semi-Gloss - Two coats Rodda 745001

Porsalite Semi-Gloss.2.3.1.3 Substrate: Aluminum.

2.3.1.3.1 Primer: Aluminum Surfaces - Prime with one coat Carboline Rustbond FC Penetrating Sealer Primer at 1.0-2.0 mils DFT.

2.3.1.3.2 Primer: Aluminum Surfaces - Prime exposed metal areas with one coat 508901 Metal Master Primer (Waterborne).










2.3.1.4 Substrate: Galvanized Metal.2.3.1.4.1 Primer: Galvanized Surfaces - Prime with one coat Carboline Galoseal WB

High Performance Wash Primer at 0.5-1.0mils DFT.2.3.1.4.2 Primer: Galvanized Surfaces - Prime exposed metal areas with one coat

508901 Metal Master Primer (Waterborne).2.3.1.4.3 Finish: Gloss, Silicone Alkyd Gloss - Two coats Rodda 75880x Powerkote

Silicone Alkyd Enamel.2.3.1.4.4 Finish: Semi-Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM








Porsalite Semi-Gloss.2.3.1.5 Substrate: Ferrous Metal: Rusting Iron or Other Ferrous Metal.

2.3.1.5.1 Primer: Rust Converter and Rusted Ferrous Metal Primer - Prime with one to two to coats (10 mils wet) 832331 Corroseal (waterborne). Allow 24 hours for cure.

2.3.1.5.2 Finish: Gloss, Silicone Alkyd Gloss - Two coats Rodda 75880x Powerkote Silicone Alkyd Enamel.

2.3.1.5.3 Finish: Semi-Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM

09 90 00-5








Porsalite Semi-Gloss.2.3.1.6 Substrate: Copper Piping.

2.3.1.6.1 Primer: Non-Ferrous Surfaces - Prime with one coat Carboline Galoseal WB Wash Primer applied at 0.5-1.0 mils DFT.

2.3.1.6.2 Primer: Non-Ferrous Surfaces - Prime exposed metal areas with one coat 508901 Metal Master Primer (Waterborne).










2.3.2 Exterior Drywall:2.3.2.1 Substrate: Drywall, Unfinished (General Areas).

2.3.2.1.1 Primer: Drywall - Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.

2.3.2.1.2 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year Commercial Warranty) Satin.

2.3.2.1.3 Finish: Flat -Two coats 512601 Ultimate II Exterior Acrylic (35 year Commercial Warranty) Flat.

2.3.2.1.4 Finish: Semi-Gloss - Two coats Rodda 542001 Unique II Interior/ Exterior Semi-Gloss.

2.3.2.1.5 Finish: Low-Gloss - Two coats Rodda 532001 Unique II Interior/ Exterior Low-Gloss.

2.3.2.1.6 Finish: Deep Colors and Accent Striping, 53203x Low Gloss - Two coats Rodda Color Base System Exterior.

2.3.2.1.7 Finish: Satin - Two coats Rodda 521101 CoverCoat AC909 Exterior Acrylic Latex Satin.

2.3.2.1.8 Finish: Velvet Flat - Two coats Rodda 511101 CoverCoat AC911 Exterior

09 90 00-6

Acrylic Latex Velvet Flat.2.3.2.1.9 Finish: Flat - Two coats Rodda 511901 CoverCoat AC910 Exterior Acrylic

Latex Flat.2.3.2.1.10 Finish: Flat - Two coats Rodda 512301 pHlex-tite acrylic elastomeric (self-

priming) Primer / Flat Finish.

2.3.3 Exterior Vinyl Siding and Shutters:2.3.3.1 Substrate: Vinyl Siding and Shutters.

2.3.3.1.1 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.3.1.2 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year

Commercial Warranty) Satin.2.3.3.1.3 Finish: Flat -Two coats 512601 Ultimate II Exterior Acrylic (35 year

Commercial Warranty) Flat.2.3.3.1.4 Finish: Semi-Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM


Crosslinking Satin Enamel.2.3.3.1.6 Finish: Semi-Gloss - Two coats Rodda 542001 Unique II Interior/ Exterior

Semi-Gloss.2.3.3.1.7 Finish: Low-Gloss - Two coats Rodda 532001 Unique II Interior/ Exterior

Low-Gloss.2.3.3.1.8 Finish: Deep Colors and Accent Striping, 53203x Low Gloss - Two coats

Rodda Color Base System Exterior.2.3.3.1.9 Finish: Satin - Two coats Rodda 521101 CoverCoat AC909 Exterior Acrylic

Latex Satin.2.3.3.1.10 Finish: Velvet Flat - Two coats Rodda 511101 CoverCoat AC911 Exterior


Latex Flat.

2.3.4 Exterior Fiberglass Doors:2.3.4.1 Substrate: Fiberglass Doors.

2.3.4.1.1 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.4.1.2 Finish: Semi Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM

Self Crosslinking Semi Gloss Enamel.2.3.4.1.3 Finish: Satin, Acrylic - Two coats Rodda 528901 Multi Master DTM Self

Crosslinking Satin Enamel.2.3.4.1.4 Finish: Semi-Gloss Acrylic -Two coats Rodda 542001 Unique II Interior/

Exterior Semi-Gloss.2.3.4.1.5 Finish: Low-Gloss - Two coats Rodda 532001 Unique II Interior/ Exterior

Low-Gloss.2.3.4.1.6 Finish: Low-Gloss Acrylic -Deep Colors and Accent Striping: Two coats

Rodda 53203x Color Base System Exterior.

2.3.5 Exterior Masonry, Concrete and Stucco:2.3.5.1 Substrate: Masonry and Brick (non-porous).

2.3.5.1.1 Primer: One coat 501801 Surfbond II Acrylic Masonry Conditioner Primer.2.3.5.1.2 Primer Finish: Rodda 512301 pHlex-tite acrylic elastomeric Primer /Finish.2.3.5.1.3 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.5.1.4 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year


Commercial Warranty) Flat.2.3.5.1.6 Finish: Flat - Two coats Rodda 512301 pHlex-tite Acrylic Elastomeric Flat

Finish at 7.5 dry mils per coat.2.3.5.1.7 Elastomeric Finish: Smooth Flat - Two coats Rodda 511301 Super Roflex

09 90 00-7

Elastomeric Coating at 7.5 dry mils per coat. Backroll to eliminate pin holes.


2.3.5.1.9 Finish: Deep Colors and Accent Striping, - Two coats Rodda 53203x Low Gloss Color Base System Exterior.

2.3.5.1.10 Finish: Low-Gloss - Two coats Rodda 532001 Unique II Exterior Acrylic Latex Low Gloss.


2.3.5.1.12 Finish: Velvet Flat - Two coats Rodda 511101 CoverCoat AC911 Exterior Acrylic Latex Velvet Flat.

2.3.5.1.13 Finish: Flat - Two coats Rodda 511901 CoverCoat AC910 Exterior Acrylic Latex Flat.

2.3.5.2 Substrate: Concrete Masonry Units (Porous).2.3.5.2.1 Block Filler: One coat Rodda 501901 Sprayable Smooth Block Filler.

Backroll to fill voids.2.3.5.2.2 Finish: Flat - Two coats Rodda 512301 pHlex-tite Acrylic Elastomeric Flat











2.3.5.3 Substrate: Cured Stucco.2.3.5.3.1 Primer: One coat 501801 Surfbond II Acrylic Masonry Conditioner Primer.2.3.5.3.2 Primer Finish: Rodda 512301 pHlex-tite acrylic elastomeric Primer /Finish.2.3.5.3.3 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.5.3.4 Finish: Flat - Two coats Rodda 512301 pHlex-tite Acrylic Elastomeric Flat







2.3.5.3.10 Finish: Low-Gloss - Two coats Rodda 532001 Unique II Exterior Acrylic

09 90 00-8

Latex Low Gloss.2.3.5.3.11 Finish: Satin - Two coats Rodda 521101 CoverCoat AC909 Exterior Acrylic



Latex Flat.2.3.5.4 Substrate: Cast Concrete.

2.3.5.4.1 Primer: One coat 501801 Surfbond II Acrylic Masonry Conditioner Primer.2.3.5.4.2 Primer Finish: Rodda 512301 pHlex-tite acrylic elastomeric Primer /Finish.2.3.5.4.3 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.5.4.4 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year











2.3.5.5 Substrate: Hot Concrete (high pH):2.3.5.5.1 Primer: One coat 501801 Surfbond II Acrylic Masonry Conditioner Primer.2.3.5.5.2 Primer Finish: Rodda 512301 pHlex-tite acrylic elastomeric Primer / Flat

Finish.2.3.5.5.3 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.5.5.4 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year










09 90 00-9


2.3.6 Exterior Hardiboard and Hardiplank:2.3.6.1 Substrate: Fiber Cement Board:

2.3.6.1.1 Primer Finish: Rodda 512301 pHlex-tite acrylic elastomeric Primer /Finish.2.3.6.1.2 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.6.1.3 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year


Commercial Warranty) Flat.2.3.6.1.5 Finish: Semi-Gloss - Two coats Rodda 542001 Unique II Interior/ Exterior

Semi-Gloss.2.3.6.1.6 Finish: Deep Colors and Accent Striping, - Two coats Rodda 53203x Low

Gloss Color Base System Exterior.2.3.6.1.7 Finish: Low-Gloss - Two coats Rodda 532001 Unique II Exterior Acrylic




Latex Flat.

2.3.7 Exterior Wood:2.3.7.1 Substrate: Wood (Opaque Paint Finish on Wood Vertical Siding).

2.3.7.1.1 Primer: One coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.7.1.2 Primer: One coat Rodda Cloverdale 15130 WeatherOne Int. / Ext. Alkyd

Stain Blocking Primer.(Solvent based)2.3.7.1.3 Primer: One coat Rodda 701501 Control Wood Alkyd Primer.(Solvent

based slow dry)2.3.7.1.4 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year


Commercial Warranty) Flat.2.3.7.1.6 Finish: Semi-Gloss - Two coats Rodda 542001 Unique II Interior/ Exterior






Latex Flat.2.3.7.2 Substrate: Wood (Opaque Paint Finish on Wood Trim, Frames and Molding).

2.3.7.2.1 Primer: One coat Rodda 501601 First Coat Acrylic Latex Primer.2.3.7.2.2 Primer: One coat Rodda Cloverdale 15130 WeatherOne Int. / Ext. Alkyd

Stain Blocking Primer.(Solvent based)2.3.7.2.3 Primer: One coat Rodda 701501 Control Wood Alkyd Primer.(Solvent

based slow dry)2.3.7.2.4 Finish: Satin -Two coats 522601 Ultimate II Exterior Acrylic (35 year


09 90 00-10

Commercial Warranty) Flat.2.3.7.2.6 Finish: Semi-Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM


Crosslinking Satin Enamel.2.3.7.2.8 Finish: Gloss - Two coats Rodda 552001 Unique II Interior/ Exterior Gloss.2.3.7.2.9 Finish: Semi-Gloss - Two coats Rodda 542001 Unique II Interior/ Exterior






Latex Flat.2.3.7.3 Substrate: Stain Finish on Vertical Wood.

2.3.7.3.1 Finish Opaque, Water Based: Cloverdale 724-Series (20 year) SharkSkin Solid Deck and Siding Stain.

2.3.7.3.2 Finish Opaque, Water Based: Cloverdale 723-Series (15 year) WeatherOne Solid Hide Acrylic Stain.

2.3.7.3.3 Finish Opaque, Alkyd: Rodda 714411 Rural Manor II Solid Oil Stain.2.3.7.3.4 Semi-Transparent, Water Based: Cloverdale WeatherOne 06680 Semi-

Transparent 100% Acrylic Stain.2.3.7.3.5 Semi-Transparent, Alkyd: Rodda 714103 Rural Manor Semi-Transparent

Stain.2.3.7.4 Substrate: Wood Decking and Porch Floors (Stain Finish):

2.3.7.4.1 Finish Opaque, Water Based: Cloverdale 724-Series (6 year) SharkSkin Solid Deck and Siding Stain.

2.3.7.4.2 Semi-Transparent, Water Based: Cloverdale WeatherOne 06680 Semi-Transparent 100% Acrylic Stain.

2.3.7.4.3 Finish Semi-Transparent: FloodPro CWF UV5 Oil Finish.

2.3.8 Exterior Pavement Traffic And Zone Marking Paint2.3.8.1 Substrate: Pavement Traffic and Zone Marking Paint:

2.3.8.1.1 Driveline Acrylic Emulsion Striping Paint - White 7341.2.3.8.1.2 Driveline Acrylic Emulsion Striping Paint - Yellow 7342.

2.4 INTERIOR PAINT SYSTEMS

2.4.1 Interior Metal:2.4.1.1 Substrate: Ferrous Metal - Structural Steel.

2.4.1.1.1 Primer: Ferrous Metal Surfaces - Prime exposed metal areas with one coat 708225 Barrier III High Solids Alkyd Metal Primer.


2.4.1.1.3 Wet Environment Finish: Water based Epoxy, Gloss - Two coats Rodda's Cloverdale Ecologic WB 70503 2 Component Epoxy.

2.4.1.1.4 Wet Environment Finish: Water based Epoxy, Semi-Gloss - Two coats Rodda's Cloverdale Ecologic WB 70504 2 Component Epoxy.

2.4.1.1.5 Wet Environment Finish: Water based Epoxy, Satin - Two coats Rodda's Cloverdale Ecologic WB 70505 2 Component Epoxy.


09 90 00-11


2.4.1.1.8 Finish: Semi-Gloss, Acrylic - Two coats Rodda 533589 WoodMaster Premium Semi-Gloss.

2.4.1.1.9 Finish: Low-Gloss, Acrylic - Two coats Rodda 533590 WoodMaster Premium Low-Gloss.

2.4.1.1.10 Finish: Semi-Gloss- Two coats Cloverdale 031 Series Renaissance Hybrid Waterborne Alkyd Enamel Semi-Gloss.

2.4.1.1.11 Finish: Satin - Two coats Cloverdale 034 Series Renaissance Hybrid Waterborne Alkyd Enamel Melamine.

2.4.1.1.12 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Gloss.2.4.1.1.13 Finish: Semi-Gloss, Acrylic - Two coats Rodda 542001 Unique II Semi-

Gloss.2.4.1.1.14 Finish: Lo Gloss Acrylic - Two coats Rodda 532001 Unique II Low Gloss.2.4.1.1.15 Finish: Side Sheen Flat Acrylic - Two coats Rodda 512001 Unique II

Scrubbable Flat.2.4.1.1.16 Zero VOC Finish Semi-Gloss: Two coats Rodda 543501 Horizon Semi-

Gloss Interior Latex.2.4.1.1.17 Zero VOC Finish Satin: Two coats Rodda 523501 Horizon Satin Interior

Latex.2.4.1.1.18 Zero VOC Finish Flat: Two coats Rodda 513501 Horizon Flat Interior

Latex.2.4.1.1.19 Ultra Low VOC Commercial Finish: Semi-Gloss - Two coats Rodda 543601

Master Painter Ultra Low Semi-Gloss Interior Latex.2.4.1.1.20 Finish: Eggshell - Two coats Rodda 533001 Lasyn Interior Latex Eggshell

Enamel.2.4.1.1.21 Ultra Low VOC Commercial Finish: Satin - Two coats Rodda 523601

Master Painter Ultra Low VOC Satin Interior Latex.2.4.1.1.22 Finish: Velvet Flat - Two coats Rodda 513001 Lasyn Interior Velvet Flat

Latex.2.4.1.1.23 Ultra Low VOC Commercial Finish: Flat - Two coats Rodda 513601 Master

Painter Ultra Low VOC Interior Latex Flat.2.4.1.2 Substrate: Ferrous Metal - Windows, Frames and Doors.

2.4.1.2.1 Primer: Ferrous Metal Surfaces - Prime exposed metal areas with one coat 708225 Barrier III High Solids Alkyd Metal Primer (Solvent Base).











2.4.1.2.12 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Gloss.

09 90 00-12

2.4.1.2.13 Finish: Semi-Gloss, Acrylic - Two coats Rodda 542001 Unique II Semi-Gloss.

2.4.1.2.14 Finish: Lo Gloss Acrylic - Two coats Rodda 532001 Unique II Low Gloss.2.4.1.2.15 Finish: Side Sheen Flat Acrylic - Two coats Rodda 512001 Unique II









Painter Ultra Low VOC Interior Latex Flat.2.4.1.3 Substrate: Aluminum.

2.4.1.3.1 Primer: Prime with one coat Carboline Galoseal WB Primer at 0.5-1.0 mils DFT (Waterborne).

2.4.1.3.2 Primer: Prime with one coat 508901 Metal Master Acrylic Primer (Waterborne).




2.4.1.3.6 Finish: Semi Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM Self Crosslinking Semi Gloss Enamel.






2.4.1.3.12 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Gloss.2.4.1.3.13 Finish: Semi Gloss, Acrylic - Two coats Rodda 542001 Unique II Semi-





Latex.

09 90 00-13

2.4.1.3.19 Ultra Low VOC Commercial Finish: Semi-Gloss - Two coats Rodda 543601 Master Painter Ultra Low Semi-Gloss Interior Latex.

2.4.1.3.20 Finish: Eggshell - Two coats Rodda 533001 Lasyn Interior Latex Eggshell Enamel.

2.4.1.3.21 Ultra Low VOC Commercial Finish: Satin - Two coats Rodda 523601 Master Painter Ultra Low VOC Satin Interior Latex.

2.4.1.3.22 Finish: Velvet Flat - Two coats Rodda 513001 Lasyn Interior Velvet Flat Latex.

2.4.1.3.23 Ultra Low VOC Commercial Finish: Flat - Two coats Rodda 513601 Master Painter Ultra Low VOC Interior Latex Flat.

2.4.1.4 Substrate: Galvanized Metal.2.4.1.4.1 Primer: Prime with one coat Carboline Galoseal WB High Performance

Wash Primer at 0.5-1.0 mils DFT (Waterborne).2.4.1.4.2 Primer: Prime with one coat 508901 Metal Master Acrylic Primer

(Waterborne).2.4.1.4.3 Wet Environment Finish: Water based Epoxy, Gloss - Two coats Rodda's

Cloverdale Ecologic WB 70503 2 Component Epoxy.2.4.1.4.4 Wet Environment Finish: Water based Epoxy, Semi-Gloss - Two coats

Rodda's Cloverdale Ecologic WB 70504 2 Component Epoxy.2.4.1.4.5 Wet Environment Finish: Water based Epoxy, Satin - Two coats Rodda's

Cloverdale Ecologic WB 70505 2 Component Epoxy.2.4.1.4.6 Finish: Semi Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM

Self Crosslinking Semi Gloss Enamel.2.4.1.4.7 Finish: Satin, Acrylic - Two coats Rodda 528901 Multi Master DTM Self

Crosslinking Satin Enamel.2.4.1.4.8 Finish: Semi-Gloss, Acrylic - Two coats Rodda 533589 WoodMaster

Premium Semi-Gloss.2.4.1.4.9 Finish: Low-Gloss, Acrylic - Two coats Rodda 533590 WoodMaster

Premium Low-Gloss.2.4.1.4.10 Finish: Semi-Gloss- Two coats Cloverdale 031 Series Renaissance Hybrid

Waterborne Alkyd Enamel Semi-Gloss.2.4.1.4.11 Finish: Satin - Two coats Cloverdale 034 Series Renaissance Hybrid

Waterborne Alkyd Enamel Melamine.2.4.1.4.12 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Gloss.2.4.1.4.13 Finish: Semi Gloss, Acrylic - Two coats Rodda 542001 Unique II Semi-










Painter Ultra Low VOC Interior Latex Flat.2.4.1.5 Substrate: Ferrous Metal - Rusting Iron or other ferrous metal.

09 90 00-14

2.4.1.5.1 Primer: Rust Converter and Rusted Ferrous Metal Primer - Prime with one to two coats (10 mils wet) 832331 Corrroseal (waterborne).










2.4.1.5.11 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Gloss.2.4.1.5.12 Finish: Semi Gloss, Acrylic - Two coats Rodda 542001 Unique II Semi-










Painter Ultra Low VOC Interior Latex Flat.2.4.1.6 Substrate: Copper Piping.

2.4.1.6.1 Primer: Prime with one coat Carboline Galoseal WB Primer at 0.5-1.0 mils DFT (Waterborne).

2.4.1.6.2 Primer: Prime with one coat 508901 Metal Master Acrylic Primer (Waterborne).





2.4.1.6.7 Finish: Satin, Acrylic - Two coats Rodda 528901 Multi Master DTM Self

09 90 00-15















Painter Ultra Low VOC Interior Latex Flat.

2.4.2 Interior Drywall:2.4.2.1 Substrate: Drywall, Unfinished (General Areas).

2.4.2.1.1 Primer: Prime with one coat Rodda 507801 ScotSeal heavy bodied Acrylic wall board sealer.

2.4.2.1.2 ZERO VOC Primer: Prime with one coat 503501 Horizon Interior Primer.2.4.2.1.3 ZERO VOC Primer: Prime with one coat Rodda 502701 Roseal II wall

board sealer.2.4.2.1.4 Primer: Prime with one coat Rodda 507901 Vapor Block wall board sealer

to achieve moisture vapor barrier rating < 1 PERM.2.4.2.1.5 Primer: Prime with one coat Rodda 532516 Ezee Wall Prep applied at 6-10

mils WFT for Smooth Level 5 finish.2.4.2.1.6 Wet Environment Finish: Water based Epoxy, Gloss - Two coats Rodda's



Cloverdale Ecologic WB 70505 2 Component Epoxy.2.4.2.1.9 Finish: Semi-Gloss, Acrylic - Two coats Rodda 548901 Multi Master DTM




09 90 00-16



Waterborne Alkyd Enamel Melamine.2.4.2.1.15 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Gloss.2.4.2.1.16 Finish: Semi-Gloss, Acrylic - Two coats Rodda 542001 Unique II Semi-


Scrubbable Flat.2.4.2.1.19 Zero VOC Finish Semi-Gloss 543501 Horizon Semi-Gloss Interior Latex.2.4.2.1.20 Zero VOC Finish Satin: Two coats Rodda 523501 Horizon Satin Interior







Painter Ultra Low VOC Interior Latex Flat.

2.4.3 Interior Masonry, Concrete and Plaster.2.4.3.1 Substrate: Masonry and Brick (non-porous):

2.4.3.1.1 Primer: One coat 501801 Surfbond II Acrylic Masonry Conditioner Primer.2.4.3.1.2 Primer: Finish: Rodda 512301 pHlex-tite acrylic elastomeric Primer /

Finish..2.4.3.1.3 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.4.3.1.4 Wet Environment Finish: Water based Epoxy, Gloss - Two coats Rodda's











09 90 00-17








Painter Ultra Low VOC Interior Latex Flat.2.4.3.2 Substrate: Concrete Masonry Units (Porous).

2.4.3.2.1 Block Filler: One coat Rodda 501901 Sprayable Smooth Block Filler. Backroll to fill voids.










2.4.3.2.11 Finish: Gloss, Acrylic - Two coats Rodda 552001 Unique II Gloss.2.4.3.2.12 Finish: Semi-Gloss, Acrylic - Two coats Rodda 542001 Unique II Semi-








Latex.

09 90 00-18

2.4.3.2.22 Ultra Low VOC Commercial Finish: Flat - Two coats Rodda 513601 Master Painter Ultra Low VOC Interior Latex Flat.

2.4.3.3 Substrate: Cast Concrete (Except Floors).2.4.3.3.1 Primer: One coat 501801 Surfbond II Acrylic Masonry Conditioner Primer.2.4.3.3.2 Primer: Finish: Rodda 512301 pHlex-tite acrylic elastomeric Primer /

Finish.2.4.3.3.3 Primer: Prime with one coat Rodda 501601 First Coat Acrylic Latex Primer.2.4.3.3.4 Wet Environment Finish: Water based Epoxy, Gloss - Two coats Rodda's


















Painter Ultra Low VOC Interior Latex Flat.2.4.3.4 Substrate: Ceiling and Overhead Surfaces - Dry Fall Finishes.

2.4.3.4.1 Finish: Flat, Latex, Rodda 513801 100 percent Acrylic Dry Fall Flat White base.

2.4.3.4.2 Finish: Flat, Rodda 513899 100 percent Acrylic Dry Fall Flat Black.2.4.3.4.3 Finish: Eggshell, Latex, Rodda 533801 Acrylic Dry Fall Eggshell White

base.2.4.3.4.4 Finish: Semi-Gloss, Latex Rodda 543801 Acrylic Dry Fall Semi-Gloss

White base.

2.4.4 Interior Wood:

09 90 00-19

2.4.4.1 Substrate: Wood - Opaque Finish.2.4.4.1.1 Primer: One coat Rodda 502001 Unique II Acrylic Enamel Undercoater.2.4.4.1.2 Wet Environment Finish: Water based Epoxy, Gloss - Two coats Rodda's



















Painter Ultra Low VOC Interior Latex Flat.2.4.4.2 Substrate: Wood - Stain with Clear Urethane Varnish Finish.

2.4.4.2.1 Stain Coat: One coat, Rodda 71600x Modern Wood Stain.2.4.4.2.2 Sealer: One coat Rodda 705100 Quick Dry Sanding Sealer, Clear.2.4.4.2.3 Finish: Satin - Rodda 725100 Aqua Master Varnish Clear Polyurethane

Satin.2.4.4.2.4 Finish: Semi-Gloss - Rodda 745100 Aqua Master Varnish Clear

Polyurethane Semi-Gloss.2.4.4.2.5 Finish Gloss: Rodda 755100 Aqua Master Varnish Clear Polyurethane

Gloss.2.4.4.3 Substrate Wood - Clear Lacquer Finish.

2.4.4.3.1 Sealer: Rodda 706400 Cat-A-Lac Sanding Sealer.2.4.4.3.2 Finish: Satin, Two coats Rodda 726400 Cat-A-Lac Pre-Catalyzed Clear

Lacquer.2.4.4.3.3 Finish: Semi-Gloss, Two coats Rodda 746400 Cat-A-Lac Pre-Catalyzed

09 90 00-20

Clear Lacquer.2.4.4.3.4 Finish: Gloss, Acrylic - Two coats Rodda 756400 Cat-A-Lac Pre-Catalyzed

Clear Lacquer.2.4.4.4 Substrate Wood - Opaque Lacquer Finish.

2.4.4.4.1 Sealer: Lacquer Primer Surfacer 706201.2.4.4.4.2 Finish: Satin, Two coats 726401 Cat-A-Lac Pre-Catalyzed Lacquer White.2.4.4.4.3 Finish: Semi-Gloss, Two coats 746401 Cat-A-Lac Pre-Catalyzed Lacquer

White.2.4.4.4.4 Finish: Gloss, Acrylic - Two coats 756401 Cat-A-Lac Pre-Catalyzed

Lacquer White.2.4.4.5 Substrate Wood - Stain or Clear Interior Waterborne Finish.

2.4.4.5.1 Stain: Cloverdale 06680 WeatherOne Semi-Transparent 100% Acrylic Stain.

2.4.4.5.2 Sealer for Clear: Cloverdale 593 Series Waterborne Alkyd Varnish (self-seal with finish coat).

2.4.4.5.3 Finish: Low Lustre, Cloverdale 59304 Waterborne Alkyd Varnish Low Lustre.

2.4.4.5.4 Finish: Satin, Cloverdale 59314 Waterborne Alkyd Varnish Satin.2.4.4.5.5 Finish: Semi-Gloss, Cloverdale 59324 Waterborne Alkyd Varnish Semi-

Gloss.2.4.4.5.6 Finish: Gloss, Cloverdale 59334 Waterborne Alkyd Varnish Gloss.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly prepared.

3.1.2 Ensure that surfaces to receive coatings are dry immediately prior to application.

3.1.3 Ensure that moisture-retaining substrates to receive coatings have moisture content within tolerances allowed by coating manufacturer. Where exceeding the following values, promptly notify Architect and obtain direction before beginning work.3.1.3.1 Concrete and Masonry: 13 percent. Cure minimum 28 days.3.1.3.2 Exterior Wood: 17 percent.3.1.3.3 Interior Wood: 15 percent.3.1.3.4 Interior Finish Detail Woodwork, Including Trim, and Casework: 10 percent.3.1.3.5 Plaster and Gypsum: 15 percent.3.1.3.6 Concrete Slab-On-Grade: Perform calcium chloride test over 24 hour period or

other acceptable test to manufacturer. Verify acceptable moisture transmission and pH levels.

3.1.4 Examine surfaces to receive coatings for surface imperfections and contaminants that could impair performance or appearance of coatings, including but not limited to, loose primer, rust, scale, oil, grease, mildew, algae, or fungus, stains or marks, cracks, indentations, or abrasions.

3.1.5 Correct conditions that could impair performance or appearance of coatings in accordance with specified surface preparation procedures before proceeding with coating application.

3.2 PREPARATION - GENERAL

3.2.1 Clean surfaces thoroughly prior to coating application.

3.2.2 Do not start work until surfaces to be finished are in proper condition to produce finished surfaces of uniform, satisfactory appearance.

09 90 00-21

3.2.3 Stains and Marks: Remove completely, if possible, using materials and methods recommended by coating manufacturer; cover stains and marks which cannot be completely removed with isolating primer or sealer recommended by coating manufacturer to prevent bleed-through.

3.2.4 Remove Mildew, Algae, and Fungus using materials and methods recommended by coating manufacturer.

3.2.5 Remove dust and loose particulate matter from surfaces to receive coatings immediately prior to coating application.

3.2.6 Remove or protect adjacent hardware, electrical equipment plates, mechanical grilles and louvers, lighting fixture trim, and other items not indicated to receive coatings.

3.2.7 Move or protect equipment and fixtures adjacent to surfaces indicated to receive coatings to allow application of coatings.

3.2.8 Protect adjacent surfaces not indicated to receive coatings.

3.2.9 Prepare surfaces in accordance with manufacturer's instructions for specified coatings and indicated materials, using only methods and materials recommended by coating manufacturer.

3.3 SURFACE PREPARATION

3.3.1 Asphalt - Pavement Markings on Bituminous Materials: Remove foreign materials that could impair coating performance or appearance; apply specified primer for maximum coating adhesion.

3.3.2 Concrete and Concrete Masonry: Clean surfaces free of loose particles, sand, efflorescence, laitance, form oil, curing compounds, and other substances which could impair coating performance or appearance.

3.3.3 Concrete Floors: Remove contaminants which could impair coating performance or appearance. Verify moisture transmission and alkaline-acid balance recommended by coating manufacturer; mechanically abrade surface SSPC SP6 or Blast Track, to achieve 80-100 grit medium-sandpaper texture.

3.3.4 Existing Coatings:3.3.4.1 Remove surface irregularities by scraping or sanding to produce uniform

substrate for coating application; apply one coat primer of type recommended by coating manufacturer for maximum coating adhesion.

3.3.4.2 If presence of lead in existing coatings is suspected, cease surface preparation and notify Architect immediately.

3.3.5 Gypsum Board: Repair cracks, holes and other surface defects with joint compound to produce surface flush with adjacent surfaces.

3.3.6 Masonry Surfaces - Restored: Remove loose particles, sand, efflorescence, laitance, cleaning compounds and other substances that could impair coating performance or appearance.

3.3.7 Metals - Aluminum, Mill-Finish: Clean surfaces with a solvent or water based industrial cleaner. Scuff sand smooth surfaces to create profile for adhesion. Flush with clean water and allow to dry, before applying primer coat. Test adhesion of primer to ensure performance.

3.3.8 Metals - Copper: Clean surfaces with a solvent or water based industrial cleaner. Scuff sand

09 90 00-22

smooth surfaces to create profile for adhesion. Flush with clean water and allow to dry, before applying primer coat. Test adhesion of primer to ensure performance.

3.3.9 Metals - Ferrous, Unprimed: Follow SSPC SP3 surface preparation. Remove rust or scale, if present, by wire brush cleaning, power tool cleaning, or sandblast cleaning; remove grease, oil, and other contaminants which could impair coating performance or appearance by solvent cleaning, with phosphoric-acid solution cleaning of welds, bolts and nuts; spot-prime repaired welds with specified primer.

3.3.10 Metals - Ferrous, Shop-Primed: Follow SSPC SP3 surface preparation. Remove loose primer and rust, if present, by scraping and sanding, feathering edges of cleaned areas to produce uniform flat surface; solvent-clean surfaces and spot-prime bare metal with specified primer, feathering edges to produce uniform flat surface.

3.3.11 Metals - Galvanized Steel (not passivated): Clean with a water-based industrial strength cleaner, apply 78100 ClovaClean adhesion promoter followed by a clean water rinse; or wipe down surfaces using clean, lint-free cloths saturated with xylene or lacquer thinner; followed by wiping the surface dry using clean, lint-free cloths. Test adhesion of primer to ensure performance.

3.3.12 Metals - Galvanized Steel, Passivated: Clean with water-based industrial strength cleaner, and/or "Brush Blast" in accordance with SSPC-SP7. After the surface has been prepared, apply recommended primer to a small area. Allow primer to cure for 7 days, and test adhesion using the "cross-hatch adhesion tape test" method in accordance with ASTM D 3359. If the adhesion of the primer is positive, proceed with a recommended coating system for galvanized metal.

3.3.13 Metals - Stainless Steel: Clean surfaces with pressurized steam, pressurized water, or water-based industrial cleaner. Test adhesion of primer to ensure performance.

3.3.14 Plaster: Repair cracks, holes and other surface defects as required to maintain proper surface adhesion. Apply patching plaster or Joint compound and sand to produce surface flush with adjacent undamaged surface. Allow a full cure prior to coating application as recommended by the patching compound manufacturer's recommendations.

3.3.15 Polyvinyl Chloride (PVC) Pipe: remove contaminants and markings with denatured alcohol scuff sand and wipe with solvent for maximum adhesion. Test adhesion before starting the job.

3.3.16 Fiberglass Doors - remove contaminants with cleaning solvent (alcohol) scuff sand and wipe. Test adhesion of primer before starting job.

3.3.17 Textiles - Insulated Coverings, Canvas or Cotton: Clean using high-pressure air and solvent of type recommended for material.

3.3.18 Wood:3.3.18.1 Seal knots, pitch streaks, and sap areas with sealer recommended by coating

manufacturer; fill nail recesses and cracks with filler recommended by coating manufacturer; sand surfaces smooth.

3.3.18.2 Apply primer coat to back of wood trim and paneling.

3.3.19 Wood Doors: Seal door tops and bottoms prior to finishing.

3.3.20 Wood - Field-Glazed Frames and Sash: Prime or seal glazing channels prior to glazing.

3.4 APPLICATION - GENERAL

3.4.1 Apply each coat to uniform coating thickness in accordance with manufacturer's instructions,

09 90 00-23

not exceeding manufacturer's specified maximum spread rate for indicated surface; thins, brush marks, roller marks, orange-peel, or other application imperfections are not permitted.

3.4.2 Allow manufacturer's specified drying time, and ensure correct coating adhesion, for each coat before applying next coat.

3.4.3 Inspect each coat before applying next coat; touch-up surface imperfections with coating material, feathering, and sanding if required; touch-up areas to achieve flat, uniform surface without surface defects visible from 5 feet (1.5 m).

3.4.4 Do not apply succeeding coat until Architect has approved previous coat; only Architect-approved coats will be considered in determining number of coats applied.

3.4.5 Remove dust and other foreign materials from substrate immediately prior to applying each coat.

3.4.6 Where coating application abuts other materials or other coating color, terminate coating with a clean sharp termination line without coating overlap.

3.4.7 Where color changes occur between adjoining spaces, through framed openings that are of same color as adjoining surfaces, change color at outside stop corner nearest to face of closed door.

3.4.8 Re-prepare and re-coat unsatisfactory finishes; refinish entire area to corners or other natural terminations.

3.5 CLEANING

3.5.1 Clean excess coating materials, and coating materials deposited on surfaces not indicated to receive coatings, as construction activities of this section progress; do not allow to dry.

3.5.2 Re-install hardware, electrical equipment plates, mechanical grilles and louvers, lighting fixture trim, and other items that have been removed to protect from contact with coatings.

3.5.3 Reconnect equipment adjacent to surfaces indicated to receive coatings.

3.5.4 Relocate to original position equipment and fixtures that have been moved to allow application of coatings.

3.5.5 Remove protective materials.

3.6 PROTECTION

3.6.1 Protect completed coating applications from damage by subsequent construction activities.

3.6.2 Repair to Architect's acceptance coatings damaged by subsequent construction activities. Where repairs cannot be made to Architect's acceptance, re-apply finish coating to nearest adjacent change of surface plane, in both horizontal and vertical directions.

END OF SECTION

09 90 00-24

arcat | free building product cad details, bim, …€¦ · web viewfinish: deep colors and accent...

Documents