ASSEMBLY INSTRUCTIONS

SOMERSET SPACESAVER

ITEM #: 06-040 WHITE

ADULT ASSEMBLY REQUIRED

Caution: This Spacesaver requires assembly by an adult because of small

parts, care should be taken in unpacking and assembly of this item

SEND REQUESTS FOR MISSING OR DAMAGED PARTS REPLACEMENTS BY EMAIL TO :

customer.service@ssi-rr.com

Young children can be killed when furniture tips over.

Don’t use for TV stand.

Use angle-braces or anchors to secure furniture to wall.

WARNING: THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF FOR A TOTAL OF 75

POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE

THAN 25 POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE

SERIOUS INJURY OR DEATH.

PARTS LIST

TOOLS NEEDED FOR ASSEMBLY: FLAT&PHILIPS SCREWDRIVER (NOT INCLUDED)

THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED.

STEP 1

STEP 1 1.Attach 1 magnet plate (F) to left door (1) by inserting 1 wood screw (D) through hole on magnet plate(F) then

tighten to left door (1) by using a Philips screwdriver.

2.Attach 1 Handle (K) to left door (1) by inserting 2 Machine screw (J) through the holes on left door (1) then

tighten to Handle (K) by using a Philips screwdriver.

3.Repeat the above steps to assemble another Magnet plate (F) & Handle (K) to right door (2).

STEP 2

STEP 2 1. Insert 2 wood dowels (A) into dowel holes on the right support board (13) .

2. Screw in 3 cam bolts (B) into the pre-threaded holes on the right support board (13) by using a Philips

screwdriver.

3. Attach 2 Hinges (E) to the right support board (13).

4. Insert 4 wood screws (D) through holes on the Hinge (E) then tighten to the right support board (13) by using a

Philips screwdriver.

5. Repeat the above step to assemble left support board (14) and another 2 Hinges (E).

STEP 3

STEP 3 1.Attach right support board (13) to upper right side panel (3) by inserting 2 wood dowels (A) into dowel holes and

inserting 3 cam bolts (B) into cam lock holes in the upper right side panel (3).

2. Insert 3 cam locks (C) into the cam lock holes on the upper right side panel (3) then rotate clockwise to secure

cam bolts (B) in place by using a Philips screwdriver.

3. Repeat the above step to assemble upper left side panel (4) and right support board (14).

STEP 4

STEP 4 1. Screw in 2 cam bolts (B) into the pre-threaded hole on upper left side panel (4) and upper right side panel (3) .

2. Insert 8 wood dowels (A) into dowel holes on upper left side panel (4) and upper right side panel (3).

3. Attach the upper section cross bar (5) to upper left side panel (3) by inserting 2 wood dowels (A) into dowel

holes on the upper section cross bar (5).

4.Attach the shelf (6) to upper left side panel (3) by inserting 1 cam bolt (B) and 2 wood dowels (A) into holes on

the shelf (6), then insert 1 cam lock (C) into cam lock hole on the shelf (6) and rotate clockwise to secure the cam

bolt (B) in place.

5.Attach upper right side panel (3) to the upper section cross bar (5) and shelf (6) by inserting 3 wood dowels (A)

into holes on the upper section cross bar (5),shelf (6) and inserting cam bolt (B) into holes on the shelf (6).

6. Insert 1 cam lock (C) into the cam lock hole on the shelf (6) and rotate clockwise to secure the cam bolt (B) in

place by using a Philips screwdriver.

STEP 5

STEP 5 1. Screw in 4pc cam bolt (B) into the pre-threaded holes on the top board (7).

2. Attached the top board (7) to the upper left side panel (4) and upper right side panel (3) by inserting the cam bolt (B)

into the cam lock holes on the upper left side panel (4) and upper right side panel (3).

3. Inert 4pc cam lock (C) into the cam lock holes on the upper left side panel (4) and upper right right side panel

(3), then rotate clockwise to secure the cam bolt (B) in place by using a Philips screwdriver.

STEP 6

STEP 6 1. Screw in 4pc cam bolt (B) into the pre-threaded holes on the lower left side panel (18) and lower right side panel (17).

2. Insert 4pc wooden dowel (A) into the holes on the lower left side panel (18) and lower right side panel (17).

3. Insert 4pc wooden dowel (A) into the holes on the rear lower cross bar (16).

4. Attach 2pc lower section top cross bars (15) to lower left side panel (18) by insert the cam bolt (B) into the cam lock holes

and insert the wooden dowel (A) into the dowel holes on the lower section top cross bar (15).

5. Insert 2pc cam locks (C) into the cam lock holes on the lower section top cross bars (15), then rotate

clockwise to secure the cam bolt (B) in place by using a Philips Screwdriver.

6. Attach the rear lower cross bar (16) to lower left side panel (18) by insert the dowels into the holes on the

lower left side panel (18).

7. Attach the lower right side panel (17) to lower section top cross bars (15) and lower cross bar (16) by insert the

cam bolt (B) into the cam lock holes on the lower section top cross bars (15) and inert the dowels into the

dowel holes on the lower section top cross bar (15) and lower right side penal (17).

8. Insert 2pc cam locks (B) into the cam lock holes on the lower section top cross bars (15) then rotate clockwise

to secure the cam bolt (B) in place by using a Philips Screwdriver.

STEP 7

STEP 7

1. Screw in 2pc cam bolt (B) into the pre-threaded holes on the middle connection board (8).

2. Insert 8pc wooden dowels (A) into the holes on the lower left side panel (18), lower right side panel (17) and

lower section top cross bars (15).

3. Attach the middle connection board (8) to pre-assembled lower left side panel (18), lower right side panel (17)

and lower section top cross bars (15) by insert the wood dowel (A) into the dowel holes and insert the cam

bolt (B) into the cam lock holes on the lower left side panel (18), lower right side panel (17) and lower section

top cross bars (15).

4. Insert 2pc cam locks (C) into the cam lock holes on the lower left side panel (18) and lower right side panel

(17), then rotate clockwise to secure the cam bolt (B) in place by using a Philip Screwdriver.

5. Screw 4pc wooden screws (O) through the holes on the lower left side panel (18) and lower right side panel

(17) and tighten to rear lower cross bar (16).

STEP 8

STEP 8

1. Screw in 4pc cam bolt (B) into the pre-threaded holes on the middle connection board (8).

STEP 9

STEP 9

1. Attach the upper assembled section to lower assembled section by insert 4 cam bolt (B) into the cam lock

holes on the

upper left side panel (4) and upper right side panel (3).

2. Insert 4pc cam locks (C) into the cam lock holes on the upper left side panel (4) and upper right side panel (3),

then rotate

clockwise to secure the cam bolt (B) in place by using a Philips Screwdriver.

STEP 10

STEP 10 1.Attach upper back board (9) & middle back board (10) together sliding into plastic connection strip (N).

2.Attach upper back board (9) and middle back board (10) to the cabinet by inserting 8 wood screws (G) through

holes on upper back board (9) then tighten into the cabinet, and inserting 4 wood screws (G) through holes on

the middle back board (10) then tighten into the cabinet by using a Philips screwdriver.

3.Attach lower back board (11) to the cabinet by inserting 8 wood screws (G) through holes on lower back board

(11) then tighten into the cabinet by using a Philips screwdriver.

4.Insert 2 wood screws (G) through holes on the joint area of middle back board (10) and lower back board (11)

then tighten into the cabinet by using a Philips screwdriver.

STEP 11

STEP 11 1. Attach left door (1) to left side panel (3) by inserting 4 wood screws (D) through holes on the hinge (E) then

tighten into left door (1) by using a Philips screwdriver.

2 . Repeat the above step to assemble the right door (2).

STEP 12

STEP 12 1. Place the drawing with hole position on the wall that you desire to fix the spacesaver, drill 2 holes on the wall.

2. Insert 2 plastic archor (L) into the holes on the wall

3. Attach the pre-assembled Spacesaver in place w/holes, then insert 2 long wood screws (M) through holes on

the upper section cross bar (5) and tighten into 2 plastic anchors (L) in the wall.

STEP 13

STEP 13 1. Insert 4 shelf holders (I) into holes on upper left side panel (3) and upper right side panel (4).

2. Make sure these 4 shelf holders (I) are on the same height.

3. Put the adjustable shelf (12) onto the shelf holders (I).

ENJOY YOUR NEW SPACESAVER!

Attention Adults: The Spacesaver should be checked periodically for damage or

loose screws/parts. Take appropriate action necessary to correct the hazard such as

tightening of screws and taking any damaged parts away from the child.

Thank you for purchasing this item. We hope you enjoy it.

You can contact us at customer.service@ssi-rr.com with any questions or comments.

RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016