attachment b -exhibit 1 technical specifications …...the entire trouser is to be seamed with...

ATTACHMENT B - EXHIBIT 1

FLHSMV RFP-030-19 of 99 ATTACHMENT B - EXHIBIT 1

TECHNICAL SPECIFICATIONS 1.0 Items Description All clothing items described as “male/men” shall be cut and fitted to industry standards typical to the male anatomy and all clothing items described as “female/women” shall be cut and fitted to industry standards typical to the female anatomy. The awarded contractor will be notified by the Department’s Contract Manager within (2) business days of contract execution to produce and send pre-production samples to the Department prior to any production runs in accordance with ATTACHMENT B, EXHIBIT 1, TECHNICAL SPECIFICATIONS, and in accordance with ATTACHMENT B, SCOPE OF SERVICES, Section 5.0, Pre-Production Samples. All items shall be finished in a manner that ensures a professional appearance, as indicated below:

a) seams should not easily spread or come apart; b) threads should not be loose or easily pulled; c) buttons should securely fasten and remain fastened while worn; d) zippers should work as intended; e) material should not be see-through when worn1; f) color should be uniform throughout the clothing item (e.g., no faded, white, or other

discernable areas); g) seams should be straight; h) hems should lay flat, unless intended to be rolled; i) sleeve length should be even (same measurement, both arms) when shirt is laid flat; j) sizing should be accurate when compared to sizing charts; and k) all garments shall be properly sized and delivered clean and well-pressed.

The American Society for Testing and Materials (ASTM), the American National Standards Institute (ANSI) and the American Association of Textile Chemists and Colorists (A.A.T.C.C.) are incorporated herein, as applicable, and apply to the below specifications. During the term of the contract that results from this solicitation, in the event the ASTM, ANSI, and/or AATCC standards are updated/revised by the Manufacturer, the Contractor shall notify the Department in writing within twenty-four (24) hours after the Contractor is notified of the change by the Manufacturer. Any improvements in any and all standards may be added to the uniforms and uniform accessories by mutual consent of the Contractor and the Department. Such mutual consent must be in writing, signed by the Contractor and the Department. The Contractor shall provide the following items, according to the specifications listed below. NOTE: SUBSTITUTES ARE NOT PERMITTED.

1 Clothing items through which undergarments, undershirts, bare skin, etc., can be seen shall be considered see-through.

https://www.astm.org/

https://www.ansi.org/

https://www.ansi.org/

https://www.aatcc.org/



A. Class A and Class B (Everyday Uniforms)

1. Female Florida Highway Patrol (FHP) Trooper Pant

Model: Spiewak SPDU28L Color: Taupe Navajo Fabric: TIC T317187PT-3, 74% Dacron polyester, 24% wool, 2% lycra 13 oz. serge

weave top dyed with Nanotex. Style: The pant shall have a plain front with quarter top front pockets, 1" wide belt

loops, two back pockets for a clean and professional appearance. The pant cuff shall be of open construction to allow for custom finishing and shall have a 35-inch inseam (unfinished). Female pattern shall be current to Department’s standards, as indicated in ATTACHMENT B, Exhibit 2, FHP Policy 6.01.

Pockets: The front pocket opening shall be a minimum 6½" long and be 6" deep from the bottom of the pocket opening. The inside front pocket facing shall be a separate piece of self-material finishing no less than 1" wide. There shall be a hidden vault pocket in the right-hand front pocket secured with a #3 YKK invisible zipper. The back pockets will have a minimum opening of 5½" and be 7 1/2" deep. Each back pocket shall have a 1 1/4” loop closure tab with a bar tack located 3/8” from point of attachment to secure the buttonhole. The loop tab shall attach to a ligne 20, durable button. Each pocket corner shall have a 3/8” triangle bar tack for reinforcement.

Buttons: All buttons shall be 100% Polyester and shall have passed ASTM 5171-1191, impact resistance testing.

Pocketing: All pocketing shall be heavy-duty black 150 denier 70% polyester / 30% cotton tuxedo pocketing with a minimum thread count of 82 x 64. The waistband and inside seam binding shall be made with pocketing material cut on the bias.

Waistband: The waistband shall be designed to allow for approximately 2” maximum of mechanical expansion though two unique double waistband panels with built in elastic 1 ¼” wide. The outer front waistband shall be held with hidden 1” x 1 ¼" elastic attached to a tapered tab of self-material. The inside waistband shall be held with 1” x 1 ¼” elastic sewn inside and folded back into a separate enclosed channel joined to the front waistband channel at the top of the front pocket opening. The elastic shall remain concealed even when the waistband is stretched to maximum potential. The curtain shall be made of heavy-duty tuxedo pocketing material, bias-cut, and shall have a continuous parallel of 7/16" rectangular piece of silicone designed to work with the corresponding Spiewak Performance Duty Uniform (SPDU) shirts for maximum shirt retention (SRS® Shirt Retention System). 2 The finished waistband shall be 2 1/8" wide and shall be closed with two crush-proof riveted oxidized metal hook and eyes. The finished waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain.

2 A system designed to hold the shirt tucked into pant/trouser.



Inner Fly/Crotch:

The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a TC #8000 interlining sewn between the fly and the fly lining to give additional stability and strength to the fly. The right fly lining shall be sewn to the left fly below the zipper and continue centered on the join seam across the inseam and end 1" onto the back seam. A separate French fly made of the outer fabric with a lining of reinforced pocketing shall be sewn to the inside right fly. The fly attachment button shall be a ligne 20, 100% polyester durable button. The button shall have passed ASTM 5171-1191 impact resistance testing.

Zipper: The trousers shall close with a #4 YKK brass memory lock zipper and have a brass bottom stop at the base of the zipper chain. A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. The bar tack shall be sewn through the zipper tape; the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located at level of the bottom zipper stop on the inside of the trouser.

Belt Loops: Each loop is to be 1” wide of double thickness, with stitching on the face side ⅜" from each edge. Except for the center back loop, which shall be tacked on, all loops shall be sewn into the bottom of the waistband and into the rocap.

Creasing: The front and back crease in the trouser legs shall incorporate permanent resin bonded silicone crease produced by Creaset™. The crease shall be properly cured to ensure that it remains permanent and will withstand any amount of laundering during the life of the pant.

Seaming: The entire trouser is to be seamed with polyester core or 100% polyester spun thread.

Labels: The trouser shall have a sewn-in label giving care instructions and an outside waistband label which shall be marked with lot number, size, fiber content, and cut number. A permanent size label shall be sewn inside on the hip pocket.

Stripe: There will be a 1” wide black stripe sewn into each side seam from the waistband that will extend to the bottom of the hem.

Sizes: Women’s sizes 2 through size 28 shall be available. Patterns must be a modern, up-to-date, short waist pattern. High waist patterns will not be accepted.

2. Male FHP Trooper Trouser Model: Spiewak SPDU28L Color: Taupe Navajo Fabric: TIC T317187PT-3, 74% Dacron polyester, 24% wool, 2% lycra 13 oz. serge

weave top dyed with Nanotex. Style: The pant shall have a plain front with quarter top front pockets, 1" wide belt loops,

two back pockets for a clean professional appearance. The pant cuff shall be of open construction to allow for custom finishing and shall have a 37 ½” inch inseam (unfinished).

Pockets: The front pocket opening shall be a minimum 6½" long and be 6" deep from the bottom of the pocket opening. The inside front pocket facing shall be a separate piece of self-material finishing no less than 1" wide. There shall be a hidden vault pocket in the right-hand front pocket secured with a #3 YKK invisible zipper. The back pockets will have a minimum opening of 5½" and be 7 1/2" deep. Each back pocket shall have a 1 1/4” loop closure tab with a bar tack located 3/8” from point



of attachment to secure the buttonhole. The loop tab shall attach to a ligne 20, durable button. Each pocket corner shall have a 3/8” triangle bar tack for reinforcement.

Waistband: The waistband shall be designed to allow for 2” maximum of mechanical expansion though two unique double waistband panels with 1” elastic built in. The front waistband shall be held with a hidden 1” X 1 1/4” elastic attached to a tapered tab of self-material. The inside waistband shall be held with 1” X 1 ¼” elastic sewn to the waistband inside fold back to a separate enclosed channel which is joined to the front waistband channel at the top of the front pocket opening. The elastic shall remain concealed even when the waistband is stretched to its maximum length. The curtain shall be made of the heavy-duty tuxedo pocketing material listed above, bias-cut, and shall have a continuous parallel 7/16" wide silicone band designed to work with the corresponding SPDU shirt for maximum shirt retention (SRS® Shirt Retention System). The finished waistband shall be 2 1/8" wide and shall be closed with two crush-proof riveted oxidized metal hook and eyes. The finished waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain.

Buttons: All buttons shall be 100% polyester and shall have passed ASTM 5171-1191, impact resistance testing.

Pocketing: All pocketing shall be heavy-duty black 150-denier 70% polyester/30% cotton tuxedo pocketing with a minimum thread count of 82 x 64. The waistband and inside seam binding shall be made with pocketing material cut on the bias.

Inner Fly/Crotch: The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a TC #8000 interlining sewn between the fly and the fly lining to give additional stability and strength to the fly. The right fly lining shall be sewn to the left fly below the zipper and continue centered on the join seam across the inseam and end 1" onto the back seam. A separate French fly made of the outer fabric with a lining of reinforced pocketing shall be sewn to the inside right fly. The fly attachment button shall be a ligne 20, 100% polyester durable button. The button shall have passed ASTM 5171-1191, impact resistance testing. There shall be a diamond shaped reinforced crotch gusset measuring 9” wide X 4 ¾” sewn with a five-needle safety stitch to prevent crotch seam failure.

Zipper: The trousers shall be closed with a #4 YKK brass memory lock zipper and have a brass bottom stop at the base of the zipper chain. A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. The bar tack shall be sewn through the zipper tape; the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located at level of the bottom zipper stop on the inside of the trouser.

Belt Loops: There should be a minimum of 5 lined belt loops on waist sizes 28, 29, 30, and a minimum of 7 lined loops on all sizes over 30. Each loop is to be 1” wide of double thickness, with stitching on the face side ⅜" from each edge. Except for the center back loop, which shall be tacked on, all loops shall be sewn into the bottom of the waistband and into the rocap.

Creasing: The front and back crease in the trouser legs shall incorporate a permanent resin bonded silicone crease produced by the Creaset™ System. The crease shall be properly cured to ensure that the crease is permanent and will withstand any amount of laundering during the life of the trouser.



Seaming: The entire trouser is to be seamed with polyester core or 100% polyester spun thread. If necessary, use steam iron, low setting.


Sizes: To be sizes 28,29,30,31,32,33,34,35,36,37,38,40 to 52 regular rise, 30 thru 52 (even sizes only) in long rise, and 28 thru 40 (even sizes only) short rise. Trousers are to have open unfinished lengths to be hemmed to individual request.

Stripe: There will be a 1” wide black stripe sewn into each side seam from the waistband that will extend to the bottom of the hem.

3. Male FHP Trooper Short Sleeve Uniform Shirt

Model: Spiewak SPDU70ZL Color: Taupe Navajo Fabric: TIC#T3510755PT-2, 74% polyester, 24% wool, 2% lycra 9-9 1/2 oz. Tropical

weave top dyed with Nanotex. Collar: The collar points shall be medium spread approximately 3" in length. The

outside edge of the collar shall be stitched with a ¼” edge stitch. The collar width at the back of the neck shall be 1 ¾”. The inside collar stand shall have a sateen fabric lining for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. The collar shall be designed to wear with the collar points spread.

Sleeves: The sleeves shall be one piece sewn into the shoulder and finished with a 1” clean turn-up with no loose threads. The sleeves and side closing seams shall be attached to the body of the shirt with an overlock and a safety stitch for reinforcement. Shall have Reece eyelets underarm for ventilation and comfort.

Shoulder Supports/Epaulets:

Shirt has contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching 1½" onto the shirt. Ends are formed to a point and will have a cut buttonhole. Finished epaulets shall measure 2" wide at armhole seam and taper to 1½" wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to the shoulder seam of shirt. Support is 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge microphone (mic) port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front placket shall contain vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top



buttonhole, which shall be set horizontally. There shall be a spare ligne 20 button sewn into the inside button facing. There shall be a hidden zipper sewn under the front placket of the shirt. There shall be 4 rectangular bands of silicone approximately 3 1/8” x 9/16” sewn 2" above the bottom of exterior shirt tail edge on front and back. The silicone bars are designed to work with the corresponding Spiewak Performance Duty Uniform (SPDU) pant waistband for maximum shirt retention (SRS® shirt retention system).

Back: The garment shall have a straight yoke back located approximately 4 ¼” below the collar seam. The inside yoke shall be lined with 100% Polyester Taffeta.

Pockets: The shirt shall have two Military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 5/8” wide X 6 3/8” long. The center bellows pleat shall be 1 ½” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and shall be 6” wide at the top and 6 ¼” wide at the outside points on the bottom of the flap. The flaps shall be attached to the shirt body 1/4” above the top of the pocket, resulting in a complete pocket measurement of 6 3/8” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro™ closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap. (Pocket dimensions may vary slightly depending on size).

Flaps: Pocket flaps are scalloped and will have non-woven fusible on the topside of flap. Pocket flaps will have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and single needle edge stitched. Flaps are double needle set to the shirt. The left flaps will have a 1½" wide pencil slot with Bar tack reinforcements on each side. Flaps will have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along the center of flap and align with pintuck stitch on box pleat (pocket). Finished pocket flaps will measure 2¾" on each end and 2⅞" at the center point.

Hidden Chest Pocket:

There shall be a #3 YKK 6 ½” concealed zipper under the front placket on right side of shirt. The pocket height shall be 9” with the pocket width extending from the facing seam to the side seam. The center of the zippered opening shall be centered at the mid- point between the top of the chest flap and the bottom of the chest pocket. The top of the concealed pocket shall align with the top of the pocket flap. Concealed shirt pocket shall be made of shirting material.

Badge Tab: The badge eyelets shall be reinforced on the inside of the shirt by means of a strip of self-material measuring 1" wide, edge stitched and folded so that no raw edges appear. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. There shall be two small (horizontal) sewn eyelets 1-1/4" apart sewn through the left front and the reinforcement strip with the bottom eyelet located 1-1/4" above the top of left flap.

Nameplate Tab: There shall be two round merrowed eyelets positioned 1 5/8” apart centered above the right pocket flap ½” above the top edge of the pocket flap.

Front: The shirt shall also have two permanent 1/16” wide military creases permanently sewn down each side from shoulder seam to bottom of the shirt and centered through each front pocket and pocket flap.



Button: All buttons shall be 100% Polyester and shall have passed ASTM 5171-1191, impact resistance testing.

Mic Ports: There shall be a ¾” merrowed and bar tacked hole positioned on each side seam placed approximately 12” up from the bottom of the shirttail.

Shirt sizes: Men Numeric Sizes (14-14.5,15,15.5,16,16.5,17,17.5,18,18.5,19-19.5,20-20.5,21-21.5)

4. Male FHP Trooper Long Sleeve Uniform Shirt

Model: Spiewak SPDU75ZL Color: Taupe Navajo Fabric: TIC#T3510755PT-2, 74% polyester, 24% wool 2% lycra 9-9 1/2 oz.

Tropical weave top dyed with Nanotex. Style: The Shirt shall be standard military style with shirttails and permanently

stitched two (2) front and three (3) back creases. Tailoring: All stitches shall be of the proper tension and size so as to avoid puckering

after the shirt has been laundered and to give best durable press performance. All sewing shall be with polyester core thread to match shirt fabric. The collar and cuffs are to be single stitched 1/4" from edge. The pockets, flaps and epaulets shall be edge stitched.

Collar: The collar points shall be medium spread approximately 3" in length. The outside edge of the collar shall be stitched with a ¼” edge stitch. The collar width at the back of the neck shall be 1 ¾”. The back of the stand shall measure 1-1/2". The inside collar shall be made of a sateen fabric for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. There shall be hidden triangle collar button-down tabs sewn underneath each collar point approximately 1” wide (at the attachment point) and 7/8” long. These tabs shall attach to hidden durable ligne 14 buttons to keep the collar secure.

Sleeves: The sleeves shall be one piece sewn into the shoulder, tapering into the finished cuffs with pressed double pleats. The cuffs shall be attached to the sleeve with a 3/8” double needle stitch and shall be 2-5/8" in width; fastening with two durable ligne 20 4-hole 100% polyester buttons. The cuffs shall be made of two pieces of base shirt material with an interlining. There shall be a shirt cuff opening with a facing of shirt material 7” X 1” tapering to a point with a closure stitch across the facing 1 ½” from the point. There shall be a buttonhole approximately 4” from the point to attach a ligne 16 durable 100% polyester button. The button shall be attached to the inside facing which shall be bound with 5/8” bias cut shirt material for reinforcement. The sleeves and side closing seams shall be attached to the body of the shirt with a merrow and a safety stitch for reinforcement. Shall have Reece eyelets underarm for ventilation and comfort.

Shoulder Supports/ Epaulets:

Shirt has contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching



1½" onto the shirt. Ends are formed to a point and will have a cut buttonhole. Finished epaulets shall measure 2" wide at armhole seam and taper to 1½" wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to shoulder seam of shirt. Support is 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge mic port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar stand to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front shall contain six (6) vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top buttonhole, which shall be set horizontally. There shall be a hidden zipper sewn under the center front placket. There shall be an inside facing of self-material on the button side 3 1/4" wide extending from the collar stand to bottom of shirt. The buttons shall be securely attached shall correspond to the buttonholes on the center facing. There shall be a spare ligne 20 and ligne 16 button sewn into the inside button facing. There shall be 4 bands of silicone 3 1/8” X 9/16” sewn into the bottom of the shirt 2” from the bottom and ¼” on the inside of the outer creases designed to work with the corresponding Spiewak Performance Duty Uniform (SPDU) pant waistband for maximum shirt retention (SRS™ shirt retention system).


Pockets: The shirt shall have two Military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 5/8” wide X 6 3/8” long. The center pleat shall be 1 ½” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and shall be 6” wide at the top and 6 ¼” wide at the outside points on the bottom of the flap. (Pocket dimensions may vary slightly depending on size) The flaps shall be attached to the shirt body 1/4” above the top of the pocket, resulting in a complete pocket measurement of 6 3/8” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap.

Flaps: Pocket flaps shall be scalloped and will have non-woven fusible on the topside of flap. Pocket flaps will have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and shall be single needle edge stitched. Flaps shall be double needle set to the shirt. The left flaps will have a 1½" wide pencil slot with Bar tack reinforcements on



each side. Flaps will have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along center of flap and align with pintuck stitch on box pleat (pocket). Finished pocket flaps will measure 2¾" on each end and 2⅞" at the center point.

Badge Tab: The badge tab is to be reinforced on inside of the shirt by means of a strip of material 1" wide edge stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. There shall be two small (horizontal) eyelets, 11/4" apart sewn through the left front and the reinforcement strip with the bottom eyelet located 11/4" above the top of left flap.

Nameplate Tab:

There shall be two round merrowed eyelets positioned 1⅝” apart centered above the right pocket flap ½” above the top edge of the pocket flap.

Creasing: Pockets and pocket flaps shall be uniform in shape and size. The front and back creases shall incorporate a permanent 1/16” stitched crease. Back: The shirt shall have 3 permanent creases, 1/16” wide on the back panel. One crease shall be located at the center back and shall start at the center of the yoke and continue straight down to the bottom edge of the shirt. Each of the other two creases shall be located at the midway point between the center crease and the shoulder seam on both the left and right sides of the center crease. Front: The shirt shall also have two permanent stitched 1/16” wide military creases down each side from the shoulder seam to the bottom of the shirt centered through each front pocket and pocket flap.



Table 1

MEN LONG SLEEVE SIZE CHART SPDU75 MEN L/S 14 1/2 15 15 1/2 16 16 1/2 17 17 1/2 18 18 1/2 19 20

Sleeve length from CB 30/31 30/31 30/31 - - - - - - - -

32/33 32/33 32/33 32/33 32/33 32/33 32/33 32/33 32/33 - - 34/35 34/35 34/35 34/35 34/35 34/35 34/35 34/35 34/35 34/35 34/35 - - - 36/37 36/37 36/37 36/37 36/37 36/37 36/37 36/37

SPDU15 MEN L/S 21 22

Sleeve length from CB - -

- - 34/35 34/35 36/37 36/37



5. Female FHP Trooper Short Sleeve Uniform Shirt

Model: Spiewak SPDU70ZL Color: Taupe Navajo

Fabric: TIC#T3510755PT-2, 74% Polyester/ 24% Wool 2% Lycra 9-9 1/2 oz. Tropical weave top dyed with Nanotex.

Style: The Shirt shall be standard military style with shirttails and permanently sewn front and back creases. Women’s shirts shall have a front opening/ placket configuration similar to the men garments with the placket on the left front side.

Tailoring: All stitches shall be of the proper tension and size so as to avoid puckering after the shirt has been laundered and to give best durable press performance. All sewing shall be with polyester core thread to match the shirt fabric. The collar shall be single stitched 1/4" from edge. The pockets, flaps and epaulets shall be edge stitched. The shirtsleeve bottom shall be finished with a 1” clean finished.

Collar: The collar points shall be medium spread approximately 3" in length. The outside edge of the collar shall be stitched with a ¼” edge stitch. The Collar width at the back of the neck shall be 1 ¾”. The inside collar stand shall be made of a sateen fabric for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. The collar shall be designed to wear with the collar points spread.



Shirt has contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching 1½" onto the shirt. Ends are formed to a point and will have a cut buttonhole. Finished epaulets shall measure 2" wide at armhole seam and taper to 1½" wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to the shoulder seam of shirt. Support is 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio



microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge mic port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar stand to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front shall contain six (6) vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top buttonhole, which shall be set horizontally. There shall be an 18-ligne snap between the third and fourth button from the top to keep the shirt from gapping. There shall be an inside facing of self-material on the button side 3 1/4" wide extending from the collar to bottom of shirt. The buttons shall be securely attached shall correspond to the buttonholes on the center facing. There shall be a spare ligne 20 button sewn into the inside button facing. There shall be a hidden zipper under the front placket of the shirt. There shall be 4 bands of silicone 3 1/8” X 9/16” sewn into the bottom of the shirt 2” from the designed to work with the corresponding SPDU pant waistband for maximum shirt retention (SRS® shirt retention system).


Pockets: The shirt shall have two Military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 ¼” wide X 5 3/8” long. The center pleat shall be 1 ¼” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and shall be 5 3/8” wide at the top and 5 ¼” wide at the outside points on the bottom of the flap. The flaps shall be attached to the shirt body 1/4” above the top of the pocket, resulting in a complete pocket measurement of 6” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap. (Pocket dimensions may vary slightly depending on size).

Flaps: Pocket flaps shall be scalloped and shall have non-woven fusible on the topside of flap. Pocket flaps shall have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and single needle edge stitched. Flaps shall be double needle set to the shirt. The left flaps shall have a



1½" wide pencil slot with Bar tack reinforcements on each side. Flaps shall have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along the center of flap and align with pintuck stitch on box pleat (pocket). Finished pocket flaps shall measure 2¾" on each end and 2⅞" at the center point.


There shall be a #3 YKK 6 ½” concealed zipper under the front placket on left side of shirt. The pocket height shall be 9” with the pocket width extending from the facing seam to the side seam. The center of the zippered opening shall be centered at the mid- point between the top of the chest flap and the bottom of the chest pocket. The top of the concealed pocket shall align with the top of the pocket flap. Concealed shirt pocket shall be made of shirting material.

Badge Tab: The badge tab is to be reinforced on inside of the shirt by means of a strip of material 1" wide edge stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. There shall be two small (horizontal) eyelets 1-1/4" apart sewn through the left front and the reinforcement strip with the bottom eyelet located 1-1/4" above the top of left flap.

Nameplate Tab:

There shall be two round merrowed eyelets positioned 1 5/8” apart centered above the right pocket flap ½” above the top edge of the pocket flap.

Creasing: Pockets and pocket flaps shall be uniform in shape and size. The front and back creases shall incorporate permanent 1/16” stitched creases. Back: The shirt shall have 3 permanent creases, 1/16” wide on the back panel. One crease shall be located at the center back and shall start at the center of the yoke and continue straight down to the bottom edge of the shirt. Each of the other two creases shall be located at the midway point between the center crease and the shoulder seam on both the left and right sides of the center crease. Front: The shirt shall also have two permanent stitched 1/16” wide military creases down each side from the shoulder seam to the bottom of the shirt centered through each front pocket and pocket flap.



Shirt sizes: Chest sizes: 30 – 48 (even sizes)



6. Female FHP Trooper Long Sleeve Uniform Shirt


Tropical weave top dyed with Nanotex. Style: The shirt shall be standard military style with shirttails and permanent

stitched front and back creases. Women’s shirts shall have a front opening/ placket configuration similar to the men’s garments with the placket on the left front side.

Tailoring: All stitches shall be of the proper tension and size so as to avoid puckering after the shirt has been laundered and to give best durable press performance. All sewing shall be with polyester core thread to match shirt fabric. The collar and cuffs are to be single stitched 1/4" from edge. The pockets, flaps and epaulets shall be edge stitched.

Collar: The collar points shall be medium spread approximately 3" in length. The outside edge of the collar shall be stitched with a ¼” edge stitch. The collar width at the back of the neck shall be 1 ¾”. The back of the stand shall measure 1-1/2". The inside collar stand shall be made of a sateen fabric for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. There shall be hidden triangle collar button-down tabs sewn underneath each collar point approximately 1” wide (at the attachment point) and 7/8” long. These tabs shall attach to hidden durable ligne 14 buttons to keep the collar secure.



Shirt has contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching 1½" onto the shirt. Ends are formed to a point and will have a cut buttonhole. Finished epaulets shall measure 2" wide at armhole seam and taper to 1½"



wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to shoulder seam of shirt. Support is 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge mic port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar stand to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front shall contain six (6) vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top buttonhole, which shall be set horizontally. There shall be an 18 ligne snap between the third and fourth button from the top to keep the shirt from gapping. There shall be a hidden zipper under the center front placket of the shirt. There shall be an inside facing of self-material on the button side 3 1/4" wide extending from the collar stand to bottom of shirt. The buttons shall be securely attached shall correspond to the buttonholes on the center facing. There shall be a spare ligne 20 and ligne 16 button sewn into the inside button facing. There shall be 4 bands of silicone 3 1/8” X 9/16” sewn into the bottom of the shirt 2” from the bottom and ¼” on the inside of the outer creases designed to work with the corresponding SPDU pant waistband for maximum shirt retention (SRS™ shirt retention system).

Back: The garment shall have a straight yoke back located approximately 4 ¼” below the collar seam. The inside yoke shall be lined with 100% polyester taffeta.

Pockets: The shirt shall have two military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 1/4” wide X 5 3/8” long. The center pleat shall be 1 1/8” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and shall be 5 3/8” wide at the top and 5 ¼” wide at the outside points on the bottom of the flap. Pocket dimensions may vary slightly depending on size. The flaps shall be attached to the shirt body 1/4” above the top of the pocket, resulting in a complete pocket measurement of 6” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap.



7. Male FHP Auxiliary Short Sleeve Shirt

Flaps: Pocket flaps shall be scalloped and will have non-woven fusible on the topside of flap. Pocket flaps will have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and shall be single needle edge stitched. Flaps shall be double needle set to the shirt. The left flaps will have a 1½" wide pencil slot with bar tack reinforcements on each side. Flaps will have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along center of flap and align with pintuck stitch on box pleat (pocket). Finished pocket flaps shall measure 2¾" on each end and 2⅞" at the center point.

Badge Tab: The badge tab is to be reinforced on inside of the shirt by means of a strip of material 1" wide edge stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. There shall be two small (horizontal) eyelets, 1- ¼" apart sewn through the left front and the reinforcement strip with the bottom eyelet located 1-1/4" above the top of left flap.

Nameplate Tab:

There shall be two round merrowed eyelets positioned 1-5/8” apart centered above the right pocket flap ½” above the top edge of the pocket flap.

Creasing: Pockets and pocket flaps shall be uniform in shape and size. The front and back creases shall incorporate permanent 1/16” stitched creases.

Back: The shirt shall have 3 permanent creases, 1/16” wide on the back panel. One crease shall be located at the center back and shall start at the center of the yoke and continue straight down to the bottom edge of the shirt. Each of the other two creases shall be located at the midway point between the center crease and the shoulder seam on both the left and right sides of the center crease. Front: The shirt shall also have two permanent stitched 1/16” wide military creases down each side from the shoulder seam to the bottom of the shirt centered through each front pocket and pocket flap.

Button: All buttons shall be 100% polyester and shall have passed ASTM 5171-1191, impact resistance testing.




Tropical weave top dyed with Nanotex. Collar: The collar points shall be medium spread approximately 3" in length.

The outside edge of the collar shall be stitched with a ¼” edge stitch. The collar width at the back of the neck shall be 1 ¾”. The inside



collar stand shall have a sateen fabric lining for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. The collar shall be designed to wear with the collar points spread.



Shirt has contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching 1½" onto the shirt. Ends are formed to a point and will have a cut buttonhole. Finished epaulets measure 2" wide at armhole seam and taper to 1½" wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to shoulder seam of shirt. Support is 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge mic port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front placket shall contain vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top buttonhole, which shall be set horizontally. There shall be a spare ligne 20 button sewn into the inside button facing. There shall be a hidden zipper sewn under the front placket of the shirt. There shall be 4 rectangular bands of silicone approximately 3 1/8” x 9/16” sewn 2" above the bottom of exterior shirt tail edge on front and back. The silicone bars are designed to work with the corresponding SPDU pant waistband for maximum shirt retention (SRS® shirt retention system).


Pockets: The shirt shall have two military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 5/8” wide X 6 3/8” long. The center bellows pleat shall be 1 ½” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and



shall be 6” wide at the top and 6 ¼” wide at the outside points on the bottom of the flap. The flaps shall be attached to the shirt body 1/4” above the top of the pocket, resulting in a complete pocket measurement of 6 3/8” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro™ closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap. (Pocket dimensions may vary slightly depending on size).

Flaps: Pocket flaps shall be scalloped and shall have non-woven fusible on the topside of flap. Pocket flaps shall have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and single needle edge stitched. Flaps shall be double needle set to the shirt. The left flaps shall have a 1½" wide pencil slot with bar tack reinforcements on each side. Flaps shall have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along center of flap and align with pintuck stitch on box pleat (pocket). Finished pocket flaps shall measure 2¾" on each end and 2⅞" at the center point.


There shall be a #3 YKK 6 ½” concealed zipper under the front placket on right side of shirt. The pocket height shall be 9” with the pocket width extending from the facing seam to the side seam. The center of the zippered opening shall be centered at the mid-point between the top of the chest flap and the bottom of the chest pocket. The top of the concealed pocket shall align with the top of the pocket flap. Concealed shirt pocket shall be made of shirting material.

Badge Tab: The badge eyelets shall be reinforced on the inside of the shirt by means of a strip of self-material measuring 1" wide, edge stitched and folded so that no raw edges appear. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. There shall be two small (horizontal) sewn eyelets 1-1/4" apart sewn through the left front and the reinforcement strip with the bottom eyelet located 1-1/4" above the top of left flap.

Nameplate Tab: There shall be two round merrowed eyelets positioned 1 5/8” apart centered above the right pocket flap ½” above the top edge of the pocket flap.

Front: The shirt shall also have two permanent 1/16” wide military creases permanently sewn down each side from shoulder seam to bottom of the shirt and centered through each front pocket and pocket flap.





8. Male FHP Auxiliary Long Sleeve Uniform Shirt

Shirt sizes: Men Numeric Sizes (14-14.5,15,15.5,16,16.5,17,17.5,18,18.5,19-19.5,20-20.5,21-21.5)


Tropical weave top dyed with Nanotex. Style: The shirt shall be standard military style with shirttails and

permanently stitched two (2) front and three (3) back creases. Tailoring: All stitches shall be of the proper tension and size so as to avoid

puckering after the shirt has been laundered and to give best durable press performance. All sewing shall be with polyester core thread to match shirt fabric. The collar and cuffs are to be single stitched 1/4" from edge. The pockets, flaps and epaulets shall be edge stitched.

Collar: The collar points shall be medium spread approximately 3" in length. The outside edge of the collar shall be stitched with a ¼” edge stitch. The collar width at the back of the neck shall be 1 ¾”. The back of the stand shall measure 1-1/2". The inside collar shall be made of a sateen fabric for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. There shall be hidden triangle collar button-down tabs sewn underneath each collar point approximately 1” wide (at the attachment point) and 7/8” long. These tabs shall attach to hidden durable ligne 14 buttons to keep the collar secure.



Shirt has contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching 1½" onto the shirt. Ends are formed



to a point and will have a cut buttonhole. Finished epaulets shall measure 2" wide at armhole seam and taper to 1½" wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to shoulder seam of shirt. Support is 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge mic port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar stand to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front shall contain six (6) vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top buttonhole, which shall be set horizontally. There shall be a hidden zipper sewn under the center front placket. There shall be an inside facing of self-material on the button side 3 1/4" wide extending from the collar stand to bottom of shirt. The buttons shall be securely attached and shall correspond to the buttonholes on the center facing. There shall be a spare ligne 20 and ligne 16 button sewn into the inside button facing. There shall be 4 bands of silicone 3 1/8” X 9/16” sewn into the bottom of the shirt 2” from the bottom and ¼” on the inside of the outer creases designed to work with the corresponding SPDU pant waistband for maximum shirt retention (SRS™ shirt retention system).


Pockets: The shirt shall have two military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 5/8” wide X 6 3/8” long. The center pleat shall be 1 ½” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and shall be 6” wide at the top and 6 ¼” wide at the outside points on the bottom of the flap. (Pocket dimensions may vary slightly depending on size). The flaps shall be attached to the shirt body 1/4” above the top of the pocket, resulting in a complete pocket measurement of 6 3/8” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap.



Table 2

MEN LONG SLEEVE (L/S) SIZE CHART

Flaps: Pocket flaps shall be scalloped and shall have non-woven fusible on the topside of flap. Pocket flaps shall have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and single needle edge stitched. Flaps shall be double needle set to the shirt. The left flaps will have a 1½" wide pencil slot with bar tack reinforcements on each side. Flaps shall have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along center of flap and align with pintuck stitch on box pleat (pocket). Finished pocket flaps shall measure 2¾" on each end and 2⅞" at the center point.

Badge Tab: The badge tab is to be reinforced on inside of the shirt by means of a strip of material 1" wide edge stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. There shall be two small (horizontal) eyelets, 1-1/4" apart sewn through the left front and the reinforcement strip with the bottom eyelet located 1-1/4" above the top of left flap.

Nameplate Tab:


Creasing: Pockets and pocket flaps shall be uniform in shape and size. The front and back creases shall incorporate a permanent 1/16” stitched crease. Back: The shirt shall have 3 permanent creases, 1/16” wide on the back panel. One crease shall be located at the center back and shall start at the center of the yoke and continue straight down to the bottom edge of the shirt. Each of the other two creases shall be located at the midway point between the center crease and the shoulder seam on both the left and right sides of the center crease. Front: The shirt shall also have two permanent stitched 1/16” wide military creases down each side from the shoulder seam to the bottom of the shirt centered through each front pocket and pocket flap.



SPDU75 MEN L/S 14 1/2 15 15 1/2 16 16 1/2 17 17 1/2 18 18 1/2 19 20

Sleeve length from CB 30/31 30/31 30/31 - - - - - - - -

32/33 32/33 32/33 32/33 32/3

3 32/33 32/33 32/33 32/33 - -



9. Female FHP Auxiliary Short Sleeve Uniform Shirt

34/35 34/35 34/35 34/35 34/3

5 34/35 34/35 34/35 34/35 34/35 34/35

- - - 36/37 36/3

7 36/37 36/37 36/37 36/37 36/37 36/37

SPDU15 MEN L/S 21 22

Sleeve length from CB - -

- - 34/35 34/35 36/37 36/37



permanently sewn front and back creases. Women’s shirts shall have a front opening/placket configuration similar to the men’s garments with the placket on the left front side.

Tailoring: All stitches shall be of the proper tension and size so as to avoid puckering after the shirt has been laundered and to give best durable press performance. All sewing shall be with polyester core thread to match the shirt fabric. The collar shall be single stitched 1/4" from edge. The pockets, flaps and epaulets shall be edge stitched. The shirtsleeve bottom shall be finished with a 1” clean finished.

Collar: The collar points shall be medium spread approximately 3" in length. The outside edge of the collar shall be stitched with a ¼” edge stitch. The collar width at the back of the neck shall be 1 ¾”. The inside collar stand shall be made of a sateen fabric for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. The collar shall be designed to wear with the collar points spread.

Sleeves: The sleeves shall be one piece sewn into the shoulder and finished with a 1” clean turn-up with no loose threads. The sleeves and side closing seams shall be attached to the body of the shirt with an



overlock and a safety stitch for reinforcement. Shall have Reece eyelets underarm for ventilation and comfort.


Shirt shall have contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching 1½" onto the shirt. Ends shall be formed to a point and will have a cut buttonhole. Finished epaulets measure 2" wide at armhole seam and taper to 1½" wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to shoulder seam of shirt. Support shall be 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge mic port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar stand to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front shall contain six (6) vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top buttonhole, which shall be set horizontally. There shall be an 18-ligne snap between the third and fourth button from the top to keep the shirt from gapping. There shall be an inside facing of self-material on the button side 3 1/4" wide extending from the collar to bottom of shirt. The buttons shall be securely attached shall correspond to the buttonholes on the center facing. There shall be a spare ligne 20 button sewn into the inside button facing. There shall be a hidden zipper under the front placket of the shirt. There shall be 4 bands of silicone 3 1/8” X 9/16” sewn into the bottom of the shirt 2” from the designed to work with the corresponding SPDU pant waistband for maximum shirt retention (SRS® shirt retention system).


Pockets: The shirt shall have two military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 ¼” wide X 5 3/8” long. The center pleat shall be 1 ¼” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and shall be 5 3/8” wide at the top and 5 ¼” wide at the outside points on the bottom of the flap. (Pocket dimensions may vary slightly depending on size). The flaps shall be attached to the shirt body 1/4”



above the top of the pocket, resulting in a complete pocket measurement of 6” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap. (Pocket dimensions may vary slightly depending on size).

Flaps: Pocket flaps shall be scalloped and will have non-woven fusible on the topside of flap. Pocket flaps will have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and single needle edge stitched. Flaps shall be double needle set to the shirt. The left flaps shall have a 1½" wide pencil slot with Bar tack reinforcements on each side. Flaps shall have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along center of flap and align with pintuck stitch on box pleat (pocket). Finished pocket flaps shall measure 2¾" on each end and 2⅞" at the center point.


There shall be a #3 YKK 6 ½” concealed zipper under the front placket on right side of shirt. The pocket height shall be 9” with the pocket width extending from the facing seam to the side seam. The center of the zippered opening shall be centered at the mid- point between the top of the chest flap and the bottom of the chest pocket. The top of the concealed pocket shall align with the top of the pocket flap. Concealed shirt pocket shall be made of shirting material.


Nameplate Tab:





10. Female FHP Auxiliary Long Sleeve Uniform Shirt






permanent stitched front and back creases. Women’s shirts shall have a front opening/ placket configuration similar to the men’s garments with the placket on the left front side.

Tailoring: All stitches shall be of the proper tension and size so as to avoid puckering after the shirt has been laundered and to give best durable press performance. All sewing shall be with polyester core thread to match shirt fabric. The collar and cuffs shall be single stitched 1/4" from edge. The pockets, flaps and epaulets shall be edge stitched.

Collar: The collar points shall be medium spread approximately 3" in length. The outside edge of the collar shall be stitched with a ¼” edge stitch. The collar width at the back of the neck shall be 1 ¾”. The back of the stand shall measure 1-1/2". The inside collar stand shall be made of a sateen fabric for comfort. There shall be a collar stay sewn inside the collar along the bottom edge of each collar to hold the collar shape and still allow the attachment of collar brass. There shall be hidden triangle collar button-down tabs sewn underneath each collar point approximately 1” wide (at the attachment point) and 7/8” long. These tabs shall attach to hidden durable ligne 14 buttons to keep the collar secure.




Shoulder Supports /Epaulets:

Shirt shall have contrasting black shoulder epaulets that will have non-woven fusible interlining. Epaulets will have ⅛" wide black decorative braid sandwiched between the epaulet on outside edge, pressed, edge stitched, set into sleeve seams, and partly tacked to the garment to allow for shoulder board placement. Epaulets shall have a crisscross diagonal box stitching 1½" onto the shirt. Ends shall be form to a point and will have a cut buttonhole. Finished epaulets shall measure 2" wide at armhole seam and taper to 1½" wide at the point. Note: point of the epaulet will finish ½" from the collar seam. A cut buttonhole eyelet will be set on the shoulder seam to accommodate the buttonhole on the epaulet. Shoulder supports shall be stitched at the collar seam and to shoulder seam of shirt. Support is 1" wide self-fabric. There shall be a hidden ligne 16 button attached 1 3/8” from the epaulet attachment button on each side under each epaulet to attach a unique microphone sling to ensure that the radio microphone is in the proper place to be deployed. There shall also be a ½” merrowed edge mic port positioned between the button hole and the Mic Tab button.

Front: The front shall have a center facing 1-1/2" wide placket extending from the collar stand to the bottom of shirt. The placket shall have an interlining for stability and a neat appearance and shall be ¼” top stitched on each side. The center front shall contain six (6) vertical buttonholes placed 3/4" from edge and 3-1/2" apart. There shall be a button at the neck corresponding with the top buttonhole, which shall be set horizontally. There shall be an 18 ligne snap between the third and fourth button from the top to keep the shirt from gapping. There shall be a hidden zipper under the center front placket of the shirt. There shall be an inside facing of self-material on the button side 3 1/4" wide extending from the collar stand to bottom of shirt. The buttons shall be securely attached and shall correspond to the buttonholes on the center facing. There shall be a spare ligne 20 and ligne 16 button sewn into the inside button facing. There shall be 4 bands of silicone 3 1/8” X 9/16” sewn into the bottom of the shirt 2” from the bottom and ¼” on the inside of the outer creases designed to work with the corresponding SPDU pant waistband for maximum shirt retention (SRS™ shirt retention system).


Pockets: The shirt shall have two Military-styled box pleated, breast patch pockets with 3-point button down flaps. The breast pocket shall be 5 1/4” wide X 5 3/8” long. The center pleat shall be 1 1/8” wide. The bottom corners of the pocket shall be cut on a 40-degree angle and shall be 1 ¼” long. The pocket flaps shall be slightly tapered and shall be 5 3/8” wide at the top and 5 ¼” wide at the outside points on the bottom of the flap. (Pocket dimensions may vary slightly depending on size) The flaps shall be attached to the shirt body 1/4” above the top of the pocket, resulting in a complete pocket



measurement of 6” long. The pocket shall be edge stitched around the perimeter and shall finish with a 3/8” turn down. The pocket corners shall be reinforced with a triangle stitch in each corner. There shall be a pencil opening on both the left and right flap. The two outside points of each pocket flap shall have concealed Velcro closures. The left breast pocket shall have a sewn pencil compartment approximately 1-5/8" wide. Each flap shall have a ligne 20 button sewn to a false buttonhole on the surface of the flap.

Flaps: Pocket flaps shall be scalloped and will have non-woven fusible on the topside of flap. Pocket flaps will have ⅛" wide black decorative braid sandwiched between the flap on the outside edges and single needle edge stitched. Flaps shall be double needle set to the shirt. The left flaps shall have a 1½" wide pencil slot with Bar tack reinforcements on each side. Flaps shall have one, vertical buttonhole set ½" above the scalloped edge. Pintuck stitch shall run along center of flap and align with the pintuck stitch on box pleat (pocket). Finished pocket flaps shall measure 2¾" on each end and 2⅞" at the center point.


Nameplate Tab:








11. Male FHP Auxiliary Uniform Trouser

Model: Spiewak SPDU28L Color: Brown

Fabric: TIC T317187PT-3, 74% Dacron polyester, 24% wool, 2% lycra,13 oz. serge weave top dyed with Nanotex

Style:

The pant shall have a plain front with quarter top front pockets, 1" wide belt loops, two back pockets for a clean professional appearance. The pant cuff shall be of open construction to allow for custom finishing and shall have a 37 ½” inch inseam (unfinished).

Pockets:

The front pocket opening shall be a minimum 6½" long and be 6" deep from the bottom of the pocket opening. The inside front pocket facing shall be a separate piece of self-material finishing no less than 1" wide. There shall be a hidden vault pocket in the right-hand front pocket secured with a #3 YKK invisible zipper. The back pockets will have a minimum opening of 5½" and be 7 1/2" deep. Each back pocket shall have a 1 1/4” loop closure tab with a bar tack located 3/8” from point of attachment to secure the buttonhole. The loop tab shall attach to a ligne 20, durable button. Each pocket corner shall have a 3/8” triangle bar tack for reinforcement. (Pocket dimensions may vary slightly depending on size).


Pocketing: All pocketing shall be heavy-duty black 150-denier 70% Polyester/30% Cotton tuxedo pocketing with a minimum thread count of 82 x 64. The waistband and inside seam binding shall be made with pocketing material cut on the bias.

Waistband:

The waistband shall be designed to allow for 2” maximum of mechanical expansion though two unique double waistband panels with 1” elastic built in. The front waistband shall be held with a hidden 1” X 1 1/4” elastic attached to a tapered tab of self-material. The inside waistband shall be held with 1” X 1 ¼” elastic sewn to the waistband inside fold back to a separate enclosed channel which is joined to the front waistband channel at the top of the front pocket opening. The elastic shall remain concealed even when the waistband is stretched to its maximum length. The curtain shall be made of the heavy-duty tuxedo pocketing material listed above, bias-cut, and shall have a continuous parallel 7/16" wide silicone band designed to work with the corresponding SPDU shirt for maximum shirt retention (SRS® Shirt Retention System). The finished waistband shall be 2 1/8" wide and shall be closed with two crush-proof riveted oxidized metal hook and eyes. The finished waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain.



Inner Fly/Crotch:

The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a TC #8000 interlining sewn between the fly and the fly lining to give additional stability and strength to the fly. The right fly lining shall be sewn to the left fly below the zipper and continue centered on the join seam across the inseam and end 1" onto the back seam. A separate French fly made of the outer fabric with a lining of reinforced pocketing shall be sewn to the inside right fly. The fly attachment button shall be a ligne 20, 100% polyester durable button. The button shall have passed ASTM 5171-1191, impact resistance testing. There shall be a diamond shaped reinforced crotch gusset measuring 9” wide X 4 ¾” sewn with a five-needle safety stitch to prevent crotch seam failure.

Zipper:

The trousers shall be closed with a #4 YKK brass memory lock zipper and have a brass bottom stop at the base of the zipper chain. A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. The bar tack shall be sewn through the zipper tape; the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located at level of the bottom zipper stop on the inside of the trouser.

Belt Loops:

There should be a minimum of 5 lined belt loops on waist sizes 28, 29, 30, and a minimum of 7 lined loops on all sizes over 30. Each loop is to be 1” wide of double thickness, with stitching on the face side ⅜" from each edge. Except for the center back loop, which shall be tacked on, all loops shall be sewn into the bottom of the waistband and into the rocap.

Creasing:

The front and back crease in the trouser legs shall incorporate a permanent resin bonded silicone crease produced by the Creaset™ System. The crease shall be properly cured to ensure that the crease is permanent and will withstand any amount of laundering for the life of the trouser.

Seaming: The entire trouser is to be seamed with Polyester core or 100% Polyester spun thread.


Sizes: To be sizes 28,29,30,31,32,33,34,35,36,37,38,40 to 52 regular rise, 30 thru 52 (even sizes only) in long rise, and 28 thru 40 (even sizes only) short rise. Trousers shall have open unfinished lengths to be hemmed to individual request.

Stripe: There shall be a 1” wide black stripe sewn onto each side seam from the waistband.



12. Female FHP Auxiliary Uniform Pant

Model: Spiewak SPDU28L Color: Brown Fabric: TIC T317187PT-3, 74% Dacron polyester, 24% wool, 2% lycra, 13 oz.

serge weave top dyed with Nanotex Style: The pant shall have a plain front with quarter top front pockets, 1” wide

belt loops, two back pockets for a clean and professional appearance. The pant cuff shall be of open construction to allow for custom finishing and shall have a 35-inch inseam (unfinished). Female pattern shall be current to Departments standards, as indicated in FHP Policy 06.01.

Pockets: The front pocket opening shall be a minimum 6½” long and be 6” deep from the bottom of the pocket opening. The inside front pocket facing shall be a separate piece of self-material finishing no less than 1” wide. There shall be a hidden vault pocket in the right-hand front pocket secured with a #3 YKK invisible zipper. The back pockets will have a minimum opening of 5½” and be 7 ½” deep. Each back pocket shall have a 1 ¼” loop closure tab with a bar tack located 3/8” from point of attachment to secure the buttonhole. The loop tab shall attach to a ligne 20, durable button. Each pocket corner shall have a 3/8” triangle bar tack for reinforcement. (Pocket dimensions may vary slightly depending on size).


Pocketing: All pocketing shall be heavy-duty black 150 denier 70% polyester / 30% cotton tuxedo pocketing with a minimum thread count of 82 x 64. The waistband and inside seam binding shall be made with pocketing material cut on the bias.

Waistband: The waistband shall be designed to allow for approximately 2” maximum of mechanical expansion though two unique double waistband panels with built in elastic 1 ¼” wide. The outer front waistband shall be held with hidden 1” x 1 ¼” elastic attached to a tapered tab of self-material. The inside waistband shall be held with 1” x 1 ¼” elastic sewn inside and folded back into a separate enclosed channel joined to the front waistband channel at the top of the front pocket opening. The elastic shall remain concealed even when the waistband is stretched to maximum potential. The curtain shall be made of heavy-duty tuxedo pocketing material, bias-cut, and shall have a continuous parallel of 7/16” rectangular piece of silicone designed to work with the corresponding SPDU shirts for shirt retention (SRS® Shirt Retention System). The finished waistband shall be 2 1/8” wide and shall be closed with two crush-proof riveted oxidized metal hook and eyes. The finished waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain.

Inner Fly/Crotch:

The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a TC #8000 interlining sewn between the fly and the fly lining to give additional stability and



13. Florida Highway Patrol Trooper Motor Breeches

strength to the fly. The right fly lining shall be sewn to the left fly below the zipper and continue centered on the join seam across the inseam and end 1” onto the back seam. A separate French fly made of the outer fabric with a lining of reinforced pocketing shall be sewn to the inside right fly. The fly attachment button shall be a ligne 20, 100% polyester durable button. The button shall have passed ASTM 5171-1191, impact resistance testing.

Zipper: The trousers shall close with a #4 YKK brass memory lock zipper and have a brass bottom stop at the base of the zipper chain. A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. The bar tack shall be sewn through the zipper tape; the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located at level of the bottom zipper stop on the inside of the trouser.

Belt Loops: Each loop is to be 1” wide of double thickness, with stitching on the face side ⅜” from each edge. Except for the center back loop, which shall be tacked on, all loops shall be sewn into the bottom of the waistband and into the rocap.

Creasing: The front and back crease in the trouser legs shall incorporate permanent resin bonded silicone crease produced by Creaset™. The crease shall be properly cured to ensure that it remains permanent and will withstand any amount of laundering for the life of the trouser.



Stripe: There shall be a 1” wide black stripe sewn onto each side seam from the waistband that will extend to the bottom of the hem.

Sizes: Women’s sizes 2 through size 28 shall be available. Patterns must be a modern up to date short waist pattern. High waist patterns will not be accepted.

Model: Spiewak SPBR28L Color: Pink tan (Taupe) Fabric: TIC T317187PT-3, 74% Dacron polyester, 24% wool, 2% lycra, 13

oz. top dyed serge with Nanotex Basic Design: Breeches shall be made using male breeches uniform patterns. Cut

shall be ¼ peg cut semi-mounted style with full cavalry reinforced (rounded) seat. Breeches shall have plain front with two quarter top front pockets, two hip pockets with flaps, and two internal side cargo pockets. Work wear industrial style construction is unacceptable and shall be cause for rejection. Sizes to be male 28-56 (Regular and



Short Rise), ¼ peg. Inseams shall be finished in lengths 25-32. Bottoms to be finished with zippers attached in a concealed style.

Pockets: The front pocket opening shall be a minimum 6½” long and be 6” deep from the bottom of the pocket opening. The inside front pocket facing shall be a separate piece of self-material finishing no less than 1” wide. The back pockets shall have a minimum opening of 5” and be 6” deep, graded according to size. Each back pocket shall have a 1 ¼” loop closure tab with a bar tack located 3/8” from point of attachment to secure the buttonhole. The loop tab shall attach to a ligne 20, durable button. Each pocket corner shall have a 3/8” triangle bar tack for reinforcement. All pocketing shall be heavy-duty black 150-denier 70% polyester, 30% cotton tuxedo pocketing with a minimum thread count of 82 x 64. The waistband and inside seam binding shall be made with pocketing material cut on the bias. (Pocket dimensions may vary slightly depending on size).

Stripe: A 1” stripe of black gabardine extending from waistband seam downward to the heel. Stripe to be single stitched 1/16”. Stripe to be turned under 3/8” and pressed flat before being sewn on. Stripe to measure exactly 1” at all points of trousers.

Waistband: The waistband shall be designed to allow for 2” maximum of mechanical expansion though two unique double waistband panels with 1” elastic built in. The front waistband shall be held with a hidden 1” X 1 ¼” elastic attached to a tapered tab of self-material. The inside waistband shall be held with 1” X 1 ¼” elastic sewn to the waistband inside fold back to a separate enclosed channel which is joined to the front waistband channel at the top of the front pocket opening. The elastic shall remain concealed even when the waistband is stretched to its maximum length. The curtain shall be made of the heavy-duty tuxedo pocketing material listed above, bias-cut, and shall have a continuous parallel 7/16” wide silicone band designed to work with the corresponding SPDU shirt for maximum shirt retention (SRS® Shirt Retention System). The finished waistband shall be 2 1/8” wide and shall be closed with two crush-proof riveted oxidized metal hook and eyes. The finished waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain.

Inner Fly/Crotch: The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a TC #8000 interlining sewn between the fly and the fly lining to give additional stability and strength to the fly. The right fly lining shall be sewn to the left fly below the zipper and continue centered on the join seam across the inseam and end 1” onto the back seam. A separate French fly made of the outer fabric with a lining of reinforced pocketing shall be sewn to the inside right fly. The fly attachment button shall be a ligne 20, 100% polyester durable button. The button shall have passed ASTM 5171-1191, impact resistance testing. There shall be a diamond shaped reinforced crotch gusset measuring 9” wide X 4 ¾” sewn with a five-needle safety stitch to prevent crotch seam failure.

Zipper: The trousers shall be closed with a #4 YKK brass memory lock zipper and have a brass bottom stop at the base of the zipper chain.



14. Florida Highway Patrol Uniform Dress Blouse/Coat

A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. The bar tack shall be sewn through the zipper tape; the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located at level of the bottom zipper stop on the inside of the trouser.

Belt Loops: There should be a minimum of 5 lined belt loops on waist sizes 28, 29, 30, and a minimum of 7 lined loops on all sizes over 30. Each loop is to be 1” wide of double thickness, with stitching on the face side ⅜” from each edge. Except for the center back loop, which shall be tacked on, all loops shall be sewn into the bottom of the waistband and into the rocap.

Creasing: The front and back crease in the trouser legs shall incorporate a permanent resin bonded silicone crease produced by the Creaset™ System. The crease shall be properly cured to ensure that the crease is permanent and will withstand any amount of laundering for the life of the trouser.



Model: Spiewak SPDB6FC Requirements:

The production of the blouse shall be first class in every respect (sample picture is at end of this section). All material necessary to produce the blouse must be first quality and the garments shall be clean, well finished and pressed. Blouses in custom made to measure sizes will be required. Custom fit blouses shall be made to individual measurements and fittings. Measurements shall be taken at various locations throughout Florida.

Fabric: 14-14 1/2oz Black Serge 55/45 pw Blouse fabrication:

• Materials – black 55% Dacron polyester and 45% wool, serge. • Style – three (3) button front, three (3) buttons on cuff, single

breasted, notched lapel style collar, cut snug at the waist, flare in skirt (same brown belt will be worn). Single back vent.

• Collar – notched lapel style collar. Pockets: Blouse shall have two (2) upper outside breast pockets with pleats

and scalloped flaps. The corners of the pockets shall be slightly rounded. The pleat in each pocket shall be 1 ½” wide. The blouse shall also have two (2) lower scalloped flaps only, no actual pocket under the flap. The blouse shall also be constructed with two (2) inside breast pockets. The pockets shall be 5 ¾” wide by 6 inches deep. The pocket opening shall be neatly piped. Dimensions for breast and lower pockets shall be scaled in accordance with



garment size and length. All four (4) pockets will accommodate a removable 24-ligne state of Florida state seal, as shown in the picture below, and as provided by FHP at the time of order. The breast pocket flap will have edge cord piping of 645-437. (Pocket dimensions may vary slightly depending on size).

Vent: Single Lining: Full lining of polyester twill fabric, black in color. Front inner cloth

shall be the best grade on nonwoven fusible pellon. Chest and shoulder of coat to be padded with hymo haircloth and felt, to be sewn with two (2) rows of blind stitch including one-inch woven bridle tape.

Sleeve: The lining shall be the same as the body lining. A Florida Highway patrol emblem shall be sewn on both sleeves one-inch below shoulder seam. Emblem sample shall be supplied by the department. There shall be a colonial cuff/flap on sleeve with 645-437 piping. Three (3) buttons on cuff.

Epaulets: Shall be 2 ¼” wide at shoulder seam and tapered to 1 ½” and the point extending well under the collar. Each epaulet shall be box stitched and button near the collar with a 24-ligne state of Florida State seal button as described below. The epaulets shall be piped in 645-437 fabrics or approved equal.

Seams: Outside body seams shall be plain. Shoulder seams shall be stayed around armhole with tape from back notch to front notch.

Outlets: Side seams – ¾” each side; ¾” in under seam. The turn-up at the bottom of the coat shall be no less than 1 ¼”.

Buttons: Front closure: three (3) 36-ligne, Florida state seal buttons. Pocket flaps and epaulets and sleeves: (12) 24-ligne Florida State seal buttons, Waterbury button company or approved equal. All buttons shall be flat style.

Buttonholes: Shall be cut first or after type, positioned ½” from edge of coat and finished with separate bartacks.

Belt hooks: Front and rear hooks. Hooks shall be removable for laundering. Shoulder Pads: Shall be ½” thick needle punch type with 100% cotton padding fill. Sewing Threads: All sewing threads shall be the best quality nylon, cotton polyester and

blends of polyester and cotton as is applicable to specific seams.



Top and Edge Stitching:

Uniform ¼” double stitching shall be used on all flaps, epaulets, upper pockets, lapel, belts and at hem of blouse.

Cutting: To ensure that the blouse/coat is precisely produced for continuity in visual effect, uniformity, and precision, and all seams are properly aligned in the event future alterations are needed, all garments are to be cut from computerized patterns utilizing a Lectra or Gerber computerized cutting system.

Fitting: All blouses/coats are to be custom made for each individual officer and produced and filed in cad computer system (computer aided design). All measurements shall be taken in the presence of an FHP representative. This official shall also be present at the try-on and shall approve alterations and acceptance of the finished product. Measurements shall be recorded, and the FHP representative shall retain one (1) copy until acceptance of the final garment is approved, at which time it will be surrendered upon demand by the Contractor. Acceptance or rejection of the garment shall be at the discretion of the above designated official. One (1) try-on is required and one (1) alteration permitted. If the uniform is judged to be unacceptable after one (1) alteration, it will be rejected and a new garment shall be produced. A rejected uniform may not be accepted after alteration for any other individual.

Color: The color shall be black. The color shall be obtained by the stock dye process.

Standards: Color fastness (carbon – arc type fade-ometer): • To light: 20 hours, no appreciable change in shade of color. • To dry cleaning, perspiration and crocking: must meet

commercially acceptable minimum standards according to the A.A.T.C.C. test methods (132-1976, 15-1976), class 4 transference of or alteration in color after dry cleaning; perspiration acid and alkaline; as well as wet and dry crocking tests.

• The residual sizing, finish, protein or other non-fibrous material, including chloroform soluble and water-soluble material, shall not exceed 2%.

Fabric Abrasion: Must meet commercially acceptable ratings. Labeling: All coats shall have a care label permanently affixed, with the

department name, officer’s name, manufacturer’s name, specification, size, date of manufacture also to have a tracking code (bar code), which corresponds to the packing slip and invoice number.

Additions: There shall be self-goods badge holder sewn above the left breast pocket, 2” long and 1” wide, with two (2) brass eyelets and sewn all the way around.



15. Florida Highway Patrol Honor Guard Blouse/Coat

Example Image:

Model: Spiewak SPDB6FH Requirements:

The production of the blouse shall be first class in every respect. All material necessary to produce the blouse must be first quality and the garments shall be clean, well finished and pressed. Blouses in custom made to measure sizes will be required. Custom fit blouses shall be made to individual measurements and fittings. Measurements shall be taken at various locations throughout Florida.

Fabric: 14-14 1/2oz Black Serge 55/45 p/w Blouse fabrication:

• Materials – black 55% Dacron polyester and 45% wool, serge. • Style – five (5) button front, three (3) buttons on cuff, single

breasted, choker style collar, cut snug at the waist, flare in skirt (same brown belt will be worn). Single back vent

• Collar – choker style collar. Pockets: Blouse shall have two (2) upper outside breast pockets with pleats

and scalloped flaps. The corners of the pockets shall be slightly rounded. The pleat in each pocket shall be 1 ½” wide. The blouse shall also have two (2) lower scalloped flaps only, no actual pocket under the flap. The blouse shall also be constructed with two (2) upper pleated patch pockets. The pockets shall be 5 ¾” wide by 6 inches deep. The pocket opening shall be neatly piped. Dimensions for breast and lower pockets shall be scaled in accordance with garment size and length. All four (4) pockets will accommodate a removable 24-ligne State of Florida state seal. The lower pockets will have a bellows patch pocket. The breast pocket flap will have edge cord piping of 645-437.(Pocket dimensions may vary slightly depending on size).

Vent: Single Lining: Full lining of polyester twill fabric, black in color. Front inner cloth

shall be the best grade on non-woven fusible pellon. Chest and shoulder of coat to be padded with hymo haircloth and felt, to be



sewn with two (2) rows of blind stitch including one-inch woven bridle tape.

Sleeve: The lining shall be the same as the body lining. A Florida Highway patrol emblem shall be sewn on both sleeves one inch below shoulder seam. Emblem sample shall be supplied by the agency. There shall be a colonial cuff/flap on sleeve with 645-437 piping. Three (3) buttons on cuff.

Epaulets: Shall be 2 ¼” wide at shoulder seam and tapered to 1 ½” and the point extending well under the collar. Each epaulet shall be box stitched and button near the collar with a 24-ligne state of Florida State seal button. The epaulets shall be piped in 645-437 fabrics or approved equal.

Seams: Outside body seams shall be plain. Shoulder seams shall be stayed around armhole with tape from back notch to front notch.

Outlets: Side seams – ¾” each side; ¾” in under seam. The turn-up at the bottom of the coat shall be no less than 1 ¼”.

Buttons: Front closure: three (3) 36-ligne, Florida state seal buttons. Pocket flaps and epaulets and sleeves: (12) 24-ligne Florida State seal buttons, Waterbury button company or approved equal. All buttons shall be flat style.

Buttonholes: Shall be cut first or after type, positioned ½” from edge of coat and finished with separate bartacks.

Belt hooks: Front and rear hooks. Hooks shall be removable for laundering. Shoulder Pads: Shall be ½” thick needle punch type with 100% cotton padding fill. Sewing Threads: All sewing threads shall be the best quality nylon, cotton polyester and

blends of polyester and cotton as is applicable to specific seams. Manufacturer shall certify that the seams, sewing threads, tensile strength elongation and number of stitches per inch will withstand the stresses exerted in the performance of the normal duties of the law enforcement officer.

Top and Edge Stitching:

Uniform ¼” double stitching shall be used on all flaps, epaulets, upper pockets, lapel, belts and at hem of blouse.

Cutting: Garments shall be cut from computerized patterns utilizing a Lectra or Gerber computerized cutting systems. This modern equipment provides and ensures the production of extremely precise patterns as well as properly aligned seams for future alterations. In maximum garment draping qualities and consistent sizing, this equipment makes possible the production of a complete set of individual customized patterns further assuring continuity in visual effect.

Fitting: All uniform garments shall be custom made to the measurements taken of the individual. All measurements shall be taken in the presence of an official designated by the Department. This official shall also be present at the try-on in the baste; shall approve alterations and acceptance of the finished product. Measurements shall be recorded, and the Department representative shall retain on (1) copy until acceptance of the final garment is approved, at which time it will be surrendered upon demand by the contractor. Acceptance or rejection of the garments shall be at the discretion of the above designated official. One (1) try-on in the baste is required and one (1) alteration permitted. If the uniform is judged to be



16. Motor Carrier Compliance Tactical BDU Pant

unacceptable after one (1) alteration, it will be rejected and a new garment shall be produced. A rejected uniform may not be accepted after alteration for any other individual.

Color: The color shall be black. The color shall be obtained by the stock dye process.

Standards: Color fastness (carbon – arc type fade ometer): • To light: 20 hours, no appreciable change in shade of color. • To dry cleaning, perspiration and crocking: must meet

commercially acceptable minimum standards according to the A.A.T.C.C. test methods (132-1976, 15-1976), class 4 transference of or alteration in color after dry cleaning; perspiration acid and alkaline; as well as wet and dry crocking tests.

• The residual sizing, finish, protein or other non-fibrous material, including chloroform soluble and water-soluble material, shall not exceed 2%.

Fabric Abrasion: Must meet commercially acceptable ratings. Labeling: All coats shall be custom made for each individual officer, and

produced and filed in cad computer system (computer aided design). All coats shall have a care label permanently affixed, with the department name, officer’s name, manufacturer’s name, specification, size, date of manufacture also to have a tracking code (bar code), which corresponds to the packing slip and invoice number.

Additions: There shall be self-goods badge holder sewn above the left breast pocket, 2” long and 1” wide, with two (2) brass eyelets and sewn all the way around.

Example Image:

Model: Spiewak SBDU30 Sizes: 28-38 all, 40-60 even only (Men), 6-24 (Women) Color: BLACK Fabric: 65% Polyester/ 35% Cotton 6.5oz/yd² wrinkle resistant Mini Rip-stop

with Ultra-Dye color fastness and stain release on face.



Style: Trouser to be a BDU style trouser with a tailored split seam construction and SRS Shirt Retention System® for dress appearance. There shall be a diamond shaped reinforced crotch gusset measuring 9” wide X 4 ¾” sewn with a five-needle safety stitch to prevent crotch seam failure.

Shirt Retention System (SRS):

The Shirt Retention System (SRS™) shall be achieved through a waistband curtain to contain a 7/8” wide tape with two rows of Snugtex sewn in the middle of the inside waist band, designed to work with the corresponding tabs on the shirt, for maximum shirt retention.

Front Closure: Zipper front, with 24 ligne top snap at center front waistband. Zipper: The trouser shall be closed with a #5 YKK nylon coil auto-lock zipper

and have a metal bottom stop at the base of the zipper chain. A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. The bar tack shall be sewn through the zipper tape, the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located towards the bottom zipper stop.

Pockets: The trouser shall have two quarter top pockets. There shall also be two BDU style side cargo pockets with asymmetrical flaps with power hook and loop closure. The right pocket shall have two internal pockets with elastic opening and the left pocket shall have one internal pocket. There shall be two back pockets with asymmetrical flaps with power hook and loop closure.

Pocketing: All pocketing shall be heavy-duty cotton pocketing. The outside waistband and inside waist band facing shall be made with shell fabric. The bottom edge of the inside waistband curtain shall be bound by pocketing material cut on the bias.

Waistband: The waistband design shall allow for 2” of mechanical expansion through two unique double waistband panels with 2” height elastic built-in. The elastic shall begin at the outseam and extend 4” (stretched) toward the back waistband on each side. The elastic shall remain concealed even when the waistband is stretched to its maximum length.

Belt Loops: There should be a minimum of 5 belt loops on waist sizes 28, 29, 30, and a minimum of 7 belt loops on sizes over 30. Each loop is to be 7/8” wide of double thickness. All belt loops shall be inserted into the bottom seam of the waistband and bartacked at the top.

Knee Protector:

There shall be an inside patch on each knee for knee protector inserts, measuring 9½” long covering the full knee width, with a 5½” opening at the inseams.

Thread: The entire trouser is to be sewn with polyester core or 100% polyester spun thread

Labels: The trouser shall have a sewn-in label giving care instructions, size, fiber content, and lot number.



17. Motor Carrier Compliance Tactical BDU Short Sleeve Shirt

Model: Spiewak SBDU10 Sizes: XS-L (Short), S-3XL (Regular), M-3XL (Long) Unisex Sizing Color: BLACK Fabric: 65% Polyester/ 35% Cotton 4.5oz/yd² wrinkle resistant Rip-stop with

superior color fastness and water/oil repellency on face and wicking on back.

Style: Shirt to be a unisex short sleeve uniform shirt with convertible collar. It shall have two-piece sleeve construction, with a mic tab on the center front placket, and a wire opening on the left side seam. It shall feature a bi-swing back, SRS shirt retention system®, and hidden button-down collar.

Shirt Retention System:

The Shirt Retention System (SRS™) shall be achieved through 4 strips 3½” long x 7/8” wide each with two rows of rubberized Snugtex, sewn into the shirt 1½” up from the bottom and 4¾” from the center front and center back, designed to work with the corresponding pant waistband for maximum shirt retention.

Pockets: There shall be two front upper BDU style patch pockets with asymmetrical flaps with power hook and loop closure. There shall be two notebook pockets under the front chest patch pockets with power hook and loop closure.

Front Closure:

The shirt shall close with a hidden zipper front and one top functional button and two snaps (one above and one below the zipper) on the center front placket.

Buttons: Buttons are to be 22 ligne corresponding to the color of the shell garment. The hidden button-down collar shall have two 14 ligne buttons.

Nameplate: There shall be a velcro loop nameplate tab 1” high covering the width of the right chest pocket flap, placed ¼” above top flap edge. There shall be corresponding embroidered nameplate strips backed by velcro hook that attach to the nameplate tab.

Mic Tab: There shall be a mic tab on the center front placket positioned in line with the top of the pocket flaps, approximately 1” wide and 2” long.

Embroidered patch: An embroidered patch, containing a minimum of 15,000 stitches, produced based on the design provided by the FHP representative, shall be applied to the left chest of each shirt.

Epaulets: Epaulets shall be stitched down with a box stitch at the shoulder head, tapering loose with a stitched down arrow end at the shoulder near neck seam, with double needle top stitching along the epaulet edges, for durability and professional appearance.

Side Panels: There shall be fine stretch dyed to match knit mesh side panels and fine stretch dyed to match knit mesh underarm sleeve panels.

Bi-Swing Back:

There shall also be fine stretch dyed to match knit mesh in the bi-swing back at the armholes.

Yoke: There shall be a back yoke made of shell fabric 3½“ high from the center back neck seam lined with fine stretch dyed to match knit mesh inside.



18. Motor Carrier Compliance Tactical Long Sleeve BDU Shirt

Model: Spiewak SBDU15 Sizes: XS-L (Short), S-3XL (Regular), M-3XL (Long) Unisex Sizing Color: Black Fabric: 65% Polyester/ 35% Cotton 4.5oz/yd² wrinkle resistant Rip-stop with

superior color fastness and water/oil repellency on face and wicking on back.

Style: Shirt to be a unisex long sleeve uniform shirt with convertible collar. It shall have two-piece sleeve construction, with a mic tab on the center front placket, and a wire opening on the left side seam. It shall feature a bi-swing back, SRS shirt retention system®, and hidden button-down collar.

Shirt Retention System: The Shirt Retention System (SRS™) shall be achieved through 4 strips 3½” long x 7/8” wide each with two rows of rubberized Snugtex, sewn into the shirt 1½” up from the bottom and 4¾” from the center front and center back, designed to work with the corresponding pant waistband for maximum shirt retention.

Sleeves: Full cut sleeves with under arms 2 1/2" wide and sleeve length mesh insert for comfort with 2 knife type pleats at cuffs. Under arm mesh insert sewn into the sleeves with 1/4" double needle stitch on both sides. Over lapped 4 3/4" long sleeve vent. Barrel cuffs with triangular tip & Velcro for closure 1/4" double needle stitch all the way around barrel cuff.

Pockets: There shall be two front upper BDU style patch pockets with asymmetrical flaps with power hook and loop closure. There shall be two notebook pockets under the front chest patch pockets with power hook and loop closure.

Front Closure:

The shirt shall close with a hidden zipper front and one top functional button and two snaps (one above and one below the zipper) on the center front placket.

Buttons: Buttons are to be 22 ligne corresponding to the color of the shell garment. The hidden button-down collar shall have two 14 ligne buttons.

Nameplate: There shall be a velcro loop nameplate tab 1” high covering the width of the right chest pocket flap, placed ¼” above top flap edge. There shall be corresponding embroidered nameplate strips backed by velcro hook that attach to the nameplate tab.

Mic Tab: There shall be a mic tab on the center front placket positioned in line with the top of the pocket flaps, approximately 1” wide and 2” long.

Embroidered Badge patch:

An embroidered badge patch, containing a minimum of 15,000 stitches, produced based on the design provided by the FHP representative shall be applied to the left side of each shirt, on the chest.

Epaulets: Epaulets shall be stitched down with a box stitch at the shoulder head, tapering loose with a stitched down arrow end at the shoulder near neck seam, with double needle top stitching along the epaulet edges, for durability and professional appearance.



19. Unisex Florida Highway Patrol 6 Pocket BDU Pant

20. Unisex Florida Highway Patrol 4 Pocket Long Sleeve BDU Coat

Side Panels: There shall be fine stretch dyed to match knit mesh side panels and fine stretch dyed to match knit mesh underarm sleeve panels.

Bi-Swing Back: There shall also be fine stretch dyed to match knit mesh in the bi-swing back at the armholes.

Yoke: There shall be a back yoke made of shell fabric 3½“ high from the center back neck seam lined with fine stretch dyed to match knit mesh inside.

Model: Propper F5201 Fabric: Fabric is 65% polyester; 35% cotton rip stop. Color: Tan Design: Pants are military style cargo pants with quarter top front pockets,

cargo pockets, back hip-pockets, button fly, reinforced seat and knee; adjustable bar-tacked waist, nylon drawstring leg closures, felled inseam, out seam and seat seam.

Features: • Four pockets with button flaps. • Pocket flaps shall be fused. • Cargo pockets shall be bellowed with drain holes • Sewn to military spec MIL-T-4407E • Tabs at waist for adjustment • Leg closures shall be fused, knotted, and tacked

Sizes: • Small through 4XL regular • Small through 3XL long • Small through L short

Model: Propper F5452 Fabric: Fabric shall be 65% polyester; 35% cotton rip stop. Color: Tan Design: Sewn to military specification MIL-C-

44048G with drain holes in bellows pockets, fused pocket flaps and collar, chest pencil pocket, two-piece double reinforced elbows, felled side seams and sleeves, adjustable sleeve buttons.

Sizes: Small through 3XL Emblems:

Receives direct embroidered FHP type logo (ELC552) as provided by a FHP representative, on the left upper front centered ½” above the pocket and an emblem (EM335) as shown in the picture below, on both sleeves ¾” below the sleeve set seam.



21. Male Florida Highway Patrol Tactical Pant

A picture of Emblem EM335 is shown below:

Model: First Tactical S114011 Color: Khaki 055

Specs:

• 65% polyester. 35% cotton blend with ARMS Technology • First Tactical’s advance fit for updated professional profile • 6.4 oz mechanical stretch 2mm x 2mm double micro-ripstop

fabric • Teflon stain repellent finish • YKK zipper • Prym snaps/ melamine button

Components: • Comfort stretch waistband, snap + button closure • 7 fused belt loops • Inner ID heat transfer label • Two exterior magazine/tool pockets • Four inner webbing lanyard loops • Hand pockets reinforced with Cordura Nylon, welded pocket

openings • Tool clip dip opening • Rear set, low profile cargo pocket, without front pleats, only

bottom gusset • Hook/loop cargo pocket flap stands up or tucks in • Tandem internal cargo pocket magazine/tool pockets • Rear set/shadow stitched double knee • Octagonal knee pocket diagonally locks in first tactical knee

pads • Running gusset runs from knee to knee for maximum

movement • Two internal hemline blousing hole buttonholes

Waist: 28-54 Length: 30-36



22. Female Florida Highway Patrol Tactical Pant

23. Waterproof Systems Shell Jacket

Model: First Tactical Style #124011 Color: Khaki 055

Specs:

• 65% polyester. 35% cotton blend with ARMS Technology • First Tactical’s advance fit for updated professional profile • 6.4 oz mechanical stretch 2mm x 2mm double micro-ripstop

fabric • Teflon stain repellent finish • YKK zipper • Prym snaps/ melamine button

Components:

• Comfort stretch waistband, snap + button closure • 7 fused belt loops • Inner ID heat transfer label • Two exterior magazine/tool pockets • Four inner webbing lanyard loops • Hand pockets reinforced with Cordura Nylon, welded pocket

openings • Tool clip dip opening • Rear set, low profile cargo pocket, without front pleats, only

bottom gusset • Hook/loop cargo pocket flap stands up or tucks in • Tandem internal cargo pocket magazine/tool pockets • Rear set/shadow stitched double knee • Octagonal knee pocket diagonally locks in first tactical knee

pads • Running gusset runs from knee to knee for maximum

movement • Two internal hemline blousing hole buttonholes

Waist: 0-20 Length: Regular/Long

Model: Spiewak S3616L Shell Fabric:

The shell fabric shall be Tactel® - 100% Nylon two-ply with a water-repellent finish.

Permanent Body Lining:

Cloth type: 100% Nylon Taffeta, 70 Denier warp and fill, color black, with a waterproof /breathable WeatherTech® coating. All lining joining seams shall be safety stitched and then sealed with 1” heat sealed tape to prevent leakage. The tape shall be applied by hot air method. All stitching through the shell lining shall be sealed with waterproof tape. The lining material shall extend through the top collar of the shell garment to form a waterproof barrier. There shall be 2 female snaps at the seam joining point and opposite, approximately 2 ¼” from the sleeve bottom, to attach to the removable liner. The jacket lining shall be 100% 210T nylon taffeta. There shall be inside zippers sewn on top of front zipper tape on both sides to accommodate an optional zip-in liner (S327). The inside facing zippers shall be #5 Delrin



reversible measuring approximately 26” long (Large/Reg). There shall be an 8” nylon coil zipper on a facing of shell material for access to the outer shell for embroidery or customization to the left front chest of jacket without sewing through waterproof membrane.

Front: There shall be a 2-way zip to the neck YKK zipper with a double storm fly that secures with 6 high compression snaps (size Large/Regular).

Pockets: There shall be 2 zippered pockets, one on each side under the double covered wind fly. Each pocket shall measure 9” long. There shall be 2, 2-way front pockets on the outside front of the jacket shell which shall be lined with fleece and snap close. Next to each front pocket, closest to the zipper, there shall be 2 Val covered, zippered storage pockets. Each pocket shall measure 8” long. Inside the jacket there shall be 2 welt covered, zippered storage pockets made of shell fabric on the outside and lining fabric on the inside of each pocket. The pockets shall measure 9 ¼” long by 6 ½” wide (+/- .5”).

Epaulets: There shall be two crossed stitched epaulets that attach to the shoulders of the garment with a snap. The epaulets shall measure 7” long by 2” wide and forming a point at the end closest to the neckline (size Large/Regular).

Bottom Band:

There shall be an elasticized back bottom band with a full front bottom band. There shall be zippered side vents that have a double snap adjustment on each side. The side vent zippers shall measure approximately 10” long.

Sleeves: The sleeves shall be two-piece, semi-modified dolman construction for complete freedom of movement. There shall be a black enameled eyelet located approximately ½” up from each cuff to allow for drainage. The shoulder seams shall have an inside facing on the sleeve side, 1 ½” wide, of WeatherTech® waterproof/breathable material and taped with sealing tape to prevent leakage. The reinforcement patch shall be 5 sided. The under sleeves shall feature ventilating pit-zips with #5 Delrin zipper that measure approximately 12” long. The pit-zips shall be covered with a welt of shell material 12” long X ½” wide.

Cuffs: There shall be a cuff formed of 2 pieces of shell material approximately 1 5/8” wide at the bottom. Half of the cuff shall be heavy-duty elastic stretched and sewn with 2 threads. There shall be a cuff tab adjustment approximately 1 ¼” wide tapering to approximately ¾” wide by 3” long with a female snap. The top half of the cuff shall be interlined and shall have 3 male snaps for cuff adjustment.

Hood: There shall be a Val covered zipper with a 3-piece, drop in, waterproof hood. The Val cover shall measure 8 ¾” long. The hood shall be constructed of shell material and lined with a Weather Tech® waterproof/breathable lining that shall drop in between the shell and lining at the collar. The hood shall be attached to the bottom of the zipper opening on the under collar. The under-collar opening shall be approximately 1” from the neckline and 2 ½” from end of the collar and close with a 7” nylon coil zipper. All hood lining joining seams shall be taped with 1” waterproof tape applied by the



24. Systems Soft Shell Liner Jacket

hot air method to prevent leakage. There shall be an elasticized draw cord with double hole, self-contained cord locks for hood adjustment and inserted into each side of the hood.

Badge Tab: The tab shall be placed in the front pocket attached with a swift tab and shall be 3 ¼” in length and 1” in width unfinished. The badge tab eyelets shall be 1 ¼” from the center of one oxidized metal eyelet to the center of the other oxidized metal eyelet.

Collar: The collar shall be made of 2 plies of the shell material with an interlining sewn to the top collar for stability and measure 3 ¾” high. The collar points shall be well shaped and symmetrical. There shall be a 7” nylon coil zipper opening on the under collar centered approximately 1” up from the neckline and 2 ½” from the top of the collar edge for the drop-in hood. There shall be 4” triangle covers on both edges of the collar to secure the optional jacket liner collars when inserted into the jacket shell.

Snaps: All snaps used throughout shall be spring loaded compression snaps. Color: Black Sizes: Regular: Small – 8XL, Longs: Medium – 8XL (ALL Sizes Standard) Emblems: Jackets shall be delivered with two (2) shoulder emblems and 1 badge

emblem attached to each Jacket. Emblem placement will be furnished to the prospective Contractor. All emblems shall be furnished to the successful vendor for manufacturing application.

Model: Spiewak S318ZXL Design: The garment shall be full cut, waist length intermediate soft-shell jacket

with performance features designed for public safety use. The garment shall have a full zip front to the top of the collar, side vent zippers, adjustable sleeves, wind-toggle system, two front waist draw cords, a back-elastic gripper, and zippered hand warmer pockets. All dimensions and lengths are based on men’s size large. Dimensions and lengths for all other sizes must be graded appropriately.

The liner must be compatible to be able to zip into any of the existing Weathertech® waterproof shell jackets.

Fabric: The fabric shall be a 3-layer soft-shell whose content is 80% polyester 20% polyurethane and whose construction is 270T/75D and weight of 315gsm. The three layers are as follows: outer face made of 100% polyester mechanical high-elastic PPT fiber, inner face made of 100% polyester 100D/144F 165-175gsm non-pill fleece, and a waterproof/breathable hydrophilic polyurethane membrane bonded in-between.

Body Detail: The front zipper shall be a 26-inch YKK #5 Vislon molded zipper. There shall be an inside storm placket with a stretch bound edge and rounded at outer corners of the top and bottom ends. The hand-warmer pockets shall have a 7” long #5 nylon coil reversed teeth zipper. The hand warmer pockets shall be lined with 100% polyester



soft tricot. Shoulders shall have mic-tabs / epaulets permanently affixed and made from same shell fabric, placed atop a stitched triangular panel wider at the shoulder (5”) and narrower at the neck seam (2¼”). The epaulets shall be 1 3/8” wide. The epaulet shall be sewn down at the armhole seam, the neck seam and the horizontal edges except for a 2 1/8” opening to accept a mic device. The opening shall be bartacked at both ends. The body of the jacket shall be tapered to allow the garment to be tucked. The sleeves shall be constructed with a separate stitched panel below the elbow. The inside of the sleeves shall be fully lined with 100% polyester smooth soft Tricot mesh, for wearer comfort, and ease of use. The gusseted cuff shall be gathered and sewn with elastic and a closure tab using power hook and loop. There shall be a loop made of shell fabric at the lower cuff sewn into the gusset seam to allow for sleeve attachment into any of the compatible Weathertech® systems shell jackets. There shall be side panels constructed under each armhole and #5 10" nylon coil side vent zippers at the bottom that shall allow access to equipment or duty belt. There shall be a 7” zippered side pocket, which aligns with the front seam of the side panel on each side of the garment. There shall be a snap tab approximately 7/8” wide by 2” long at the bottom of the side vent zipper equipped with the female snap head at the end of the tab designed to snap to the male side of the snap which shall be placed on the front bottom sweep of the jacket.

Inside Detail/Pockets:

Two large inside pockets are to be in the garment constructed of two layers of tricot with a bound opening at the top. The inside pockets shall extend from the center front to the front seam of the side panels. There shall be a tunneled draw cord at the bottom sweep on the front of the jacket. The tunnel shall be created by folding the hem of the shell fabric at the base of the garment. The draw cord shall be elasticized, and the ends of the draw cord shall be sewn down inside the tunnel at the front placket vertical seam and the side seam of the front panel and shall exit the tunnel at either side of the garment through two finished eyelet holes. At the exits, the draw cord shall have a bead and barrel lock to allow the cord to be tightened. There shall be a snap tab on each front panel side seam on the inside of the garment 1½” up from the bottom to secure the elasticized shock cord when tightened. The snaps on the tabs shall be compression 24L black oxidized snaps with matte finish caps. The back bottom inside band of the garment shall have a 1” wide elasticized gripper, two Vertical Chest Pockets with angled pocket bags, and two sleeve RFID Pockets, one on each sleeve. Jackets shall be delivered with two (2) shoulder emblems and one (1) badge emblem attached to each jacket. Emblem placement will be furnished to the prospective Contractor. All emblems shall be furnished to the successful vendor for manufacturing application. STATE TROOPER shall be silk screened in 3” Letters across the back.

Color: Black Sizes: Regular S - 8XL, Long: M - 8XL



25. Systems ANSI Class 3 Rain Jacket

Model: Spiewak S366VZR General Design:

The jacket shall be a High Visibility, full zip to the neck garment with waterproof, taped seams, drop in hood, and reflective tape for safety and visibility of the wearer. The jacket shall be designed to accommodate the following zip-in / zip-out liners and stand-alone jackets: S318Z/S318ZX Soft Shells, S319V Soft Shell, S327 Fleece Jacket, S525V Jacket/Vest, and the S526CF fleece lined jacket. The S366VZR shall comply with all the requirements to meet the ANSI 107-2015 Class 3 standard without exceptions. All measurements mentioned in the construction specifications are based on stock size Large/Regular.

Shell Fabric: The high visibility shell fabric shall be windproof, waterproof, breathable, and compliant to ANSI 107. The fabric shall be 100% polyester oxford laminated to a waterproof-breathable pigmented polyurethane membrane. The warp and fill shall be 300-denier yarn, and the fabric shall weigh 190g/m² (5.6oz/yd²) +/-5%. There shall be a Teflon water repellency finish applied to the face of the fabric. All seams and retro-reflective tape shall be sealed with hot air applied thermoplastic polyurethane waterproof sealing tape to ensure waterproof integrity. The outer shell fabric shall be color hi-visibility yellow (color code 062). The minimum fabric requirements shall meet the performance levels for the High Visibility oxford fabric as listed below.

Colorfastness to Crocking:

The color fastness to crocking both wet and dry shall be at least a 3.0 by the ANSI/ISEA 107-2015 standard in accordance with AATCC 8-2013. S366VZR fabric (dry & wet) 4.0

Colorfastness to Perspiration:

The color fastness to perspiration should be at least a grade 4.0 for color change by the Gray Scale for color change in accordance with AATCC 15-2013. S366VZR fabric 4.0

Colorfastness to Laundry:

Machine Laundering Domestic/Commercial Test Method AATCC 61-2013(2A) 105 ° F. The color fastness to laundry shall have been tested to be at least a grade of 4.0. S366VZR fabric 4.5

Dimensional Stability (washing):

Dimensional change shall not exceed +/-4% in length and +/-2% in width. S366VZR fabric Length: +/- 2% Width: +/- 1%

Determination of Color – ANSI 107-2015

The color shall have been measured in accordance with the procedures defined in ASTM E1164-02 (Single Layer). Test specimen must fulfill the colorimetric requirements of Table 3, ANSI 107-2015, for background material.



Tear Resistance - ASTM D1424-09 (2013)

The woven fabric shall have passed ASTM D1424-09 (2013) at minimum of 13N in both directions. S366VZR fabric Ave. Force machine 30N Ave. Force cross machine 30N

Breathability ASTM E96-13 PROCEDURE BW (Water Vapor Transmission)

{Inverted Water Method at 73.4ºF (23ºC) and 50+2%RH, back side facing water} Minimum requirement – 3,600 g/m² /24 hr S366VZR fabric 3,670 g/m² /24 hr

Water Resistance AATCC 35-2013

ANSI 107–2015 Requirement in Sec 8.5.2: < 1g of water penetration S366V as received: 0.3g of water penetration. After 5 launderings: 0.4g of water penetration.

Water Resistance AATCC 127-2017 (Hydrostatic Pressure Test)

{Hydrostatic Head; rate of increase of water pressure: 60 mbar/min temperature of distilled water: 20ºC, face side facing water} Minimum requirement 2,000mm as received and after 5 launderings S366VZR fabric > 10,000mm of water as received and after 5 launderings.

Water Repellence AATCC22-2010

Manufacturer certified to 90 new, 70 after 5 washings S366VZR as received: 100 new, 80 after 5 launderings.

Reflective Tape:

There shall be 2” wide silver retro-reflective tape sewn 360° around the shell of the garment for safety and visibility of wearer. Each band of retro-reflective tape shall have a ¼” black colored band located on both the top and bottom of the silver retro-reflective tape. The reflective properties and configuration of retro-reflective tape shall meet and exceed ANSI 107- 2015 Class 3 minimum requirements. The placement configuration shall consist of two horizontal bands of reflective tape on the body and sleeves of the jacket and a harness configuration over each shoulder of the garment. The bottom reflective horizontal stripe shall be placed 7½” from bottom opening of jacket. The upper horizontal reflective band shall be placed 14½” from high point shoulder. There shall be two horizontal bands of reflective tape sewn onto each sleeve. The bottom reflective sleeve band shall measure 4¼” from the bottom edge of the tape to the bottom edge of the sleeve opening (+/- ¼”). The upper reflective sleeve band shall measure 9” from bottom of top band and top of bottom band. The vertical reflective tape band shall be placed 3” from the neck seam on either shoulder.

Front: The rain jacket shall have a center front #5 YKK molded, 2-way zipper extending to the edge of the collar. The center front zipper shall measure approximately 29½” long (size large/regular). There shall be an outside wind fly of self-goods measuring approximately 33 3/16” long by 3” wide (+/- ¼”) from the collar edge to the bottom of the jacket. The front wind fly shall close with seven, 22-ligne high compression snaps. The seven compression snaps on the front wind fly shall be placed approximately 5 1/8” (+/- ¼”) apart center-to-center. The jacket shall feature angled, flap-covered front pockets that shall be placed on the front of the garment on either side. On the wearer’s



left side, the high point of the pocket flap shall be measure 5 7/16” from the front zipper and 7/16” below the bottom of the upper horizontal reflective tape band. On the wearer’s right side, the high point of the pocket flap shall measure 5½” from the right side of the front wind fly and 7/16” down from the bottom of the upper horizontal reflective tape band. The inside of the pockets shall measure 6½” wide x 7½” deep. The pocket lining shall be190T taffeta (yellow). The pocket flaps shall measure approximately 7 11/16” long x approximately 2 1/16” high and shall conceal a welt construction (covered by the pocket flap). The under-pocket flap welt construction shall measure 6½” long x 3/8” high. There shall be a bar tack at each end of the pocket flap for additional reinforcement.

Front, Back, & Sleeves:

The front, back, and sleeves shall be made from one piece of shell fabric forming a semi-dolman sleeve without a shoulder seam to prevent a possibility of leakage. The sleeves shall be joined with an underarm seam and shall be a 2-piece coat style construction finished with a ½ elasticized 2” cuff with a snap tab closure. There shall be three snaps for cuff adjustment. The snap tab closure shall be made of self-goods approximately 3¼” long X 1” wide tapering to the bottom snap head. The functional pit zip shall be located under the arm and placed between the upper reflective horizontal jacket stripe and the upper horizontal reflective sleeve stripe. The under-arm zipper shall feature functional, ventilating pit-zips with a black, YKK #5 nylon coil closed end zipper measuring approximately 6” long. The pit-zips shall be covered with a welt of shell material 6½” long x 5/8” wide. The pit zip shall be lined with the same mesh material as the inside body. The armpit zipper shall zip toward sleeve.

Collar and Hood:

The stand-up collar shall measure approximately 4½” in height at center back from top of collar to collar seam and shall measure approximately 26” long from end to end and shall feature a 3-piece drop in hood. The side panels of the hood shall measure approximately 12” high x 8 7/8” wide. The middle section of the 3-piece hood shall measure approximately 4¼” wide and shall be sewn single needle raised. The hood shall have a tunneled draw cord made of multi-strand braided, nylon 1/8” wide, black in color and sewn into a channel at the perimeter of the hood with adjustment secured by a spring-loaded barrel lock on either side of hood. The tension loaded barrel lock shall measure approximately 1” long x 3/8” wide x ¼” deep and shall be black in color. The 39” long draw cord shall exit the hood channel via a ligne-14 metal eyelet with a 3/16” opening and placed 7/8” from end of hood channel opening to center of eyelet. The hood shall be fully lined with 210T nylon taffeta (color black). The collar shall feature a horizontally centered, Val cover of self-fabric, placed directly over the zippered hood “pocket” to ensure waterproof integrity of the garment. The hood zipper shall be black, YKK #3, nylon coil and shall measure approximately 9½“ long. The Val cover shall measure approximately 10 5/8” long x 2¼” wide.



26. High Visibility Public Safety Vest ANSI/ISEA 207-2010 Compliant

Inside Detail: The inside of the jacket shall be partially lined with a polyester mesh fabric approximately 22” from the top of collar (size large/regular). The inside mesh lining shall be 100% polyester, 55/GSM, 150cm, Azo-free, yarn size 50 denier, knit machine 28 gauge, 9 stitches per inch, 1 mm holes, black color and shall have a two way stretch minimum of 20% one way and 35% the other way. The woven, non-fusible interlining (white) shall be located between the plies of the pocket flaps, collar, snap tabs, Val cover, and front placket. The main label shall be sewn onto a carrier of 210T nylon for stability. There shall be a hanger loop of self-fabric centered and sewn into the collar. There shall be a reinforcement panel of 100% 210T nylon approximately 7” long below the mesh lining on the inside back and front. At the bottom of the reinforcement panel there shall be a black, closed end, YKK #5, nylon coil, 20” zipper. There shall be a bottom kicker of shell material approximately 4¾” wide for additional reinforcement. On the inside left mesh panel there shall be a pocket of 210T nylon taffeta measuring approximately 8” high x 7” wide with a 7/8” wide x 1” long a power hook and loop closure. The pocket shall be edge stitched and finished on the top with 1” turn up of pocketing material. The sleeves shall be fully lined with 210T nylon taffeta (black). On the inside bottom left nylon panel there shall be an HVG warning label with care instructions, an ANSI 107-2015 Class 3 compliance pictogram and a garment care content label.

Side Vents: There shall be zippered side vent openings on either side of the jacket with black closed end, YKK #5, nylon coil zippers measuring approximately 13½" to allow access to equipment. There shall be a wind fly covering of shell material measuring 14½" long x 3“ wide and secured by two metal compression snaps on either side of the jacket for additional increment weather protection.

Sizes: Regular: S – 6XL, Long: M – 6XL

Model: Spiewak S912L Specification: The following specification outlines the garment requirements for High

Visibility Personal Protective Equipment designed for enhanced visibility while working in or adjacent to the roadway for Public Safety Personnel and First Responders. The performance and design criteria of this garment shall be established to provide wearer conspicuity and enhance high visibility over a wide range of lighting and environmental conditions in the work setting such as twilight, overcast, rain, snow, daylight, and night.

HVG Construction:

The High Visibility Garment shall be home launderable. All materials shall be durable. The garment must fit comfortably on wearer and thus promote continuing use.



HVG Base Material:

Base fabric shall be 100% lime-yellow polyester knit mesh with a density to meet ANSI 207-2006 specifications as a fluorescent background material. The minimum fluorescence is 4.0. Shrinkage shall be less than 3% warp, 3% fill. Piling shall meet a random tumble level minimum 4.5. Garment shall have a bias binding around the edges of the vest. The binding shall have a 0.5” width and shall be of high visibility fluorescent fabrics matching the background mesh.

HVG Marking Material:

The high visibility tricot trim shall be ANSI 207-2006 compliant. It shall be 4.5” wide and of 100% polyester tricot. The trim color shall be fluorescent lime-yellow color and piece-dyed for stability. All retro-reflective material shall be 3M 8710, 2” wide silver film 51hermos fuse bonded onto the center of the 2 ½” wide black cord. Front shall read FHP in Black Letters. Back shall read STATE TROOPER in black letters. The fluorescent lime-yellow trim material shall be sewn onto the vest for maximum conspicuity. It shall be sewn vertically over each shoulder, down the front and back and with a horizontal trim band sewn around the torso to maintain 360-degree visibility of wearer.

HVG Labeling: Each garment shall have a VizGuard® by Spiewak woven main label and a woven size and care label sewn under the main label. Each garment shall have an ANSI compliant pictogram denoting ANSI 207-2006 compliance and a 3M woven label.

HVG Closures: The front zipper closure shall be a #5, heavy-duty black nylon molded zipper that shall measure approximately 8” long (size 2XL).

HVG Sizing: The garment is available in the following size range to promote year- round use and so that wearer can adjust Safety Vest for use in warmer climates over a t-shirt and for colder weather over a Department issued Duty Jacket: Medium = (XS – Medium) XXL = (Large – 2XL) 4XL = (3XL – 4XL) 6XL = (5XL – 6XL) Vests shall have FHP black lettering placed vertically on the front down each reflective striping and STATE TROOPER placed horizontally across the back on the reflective striping. NOTE: Size 2XL shall have a front length of 25” and a center back length of 25” so as not to deny access to wearer’s equipment belt or other items worn by wearer or external.

HVG Size Adjustment System:

The side closures shall be constructed of compliant trim, as specified, on both sides utilizing Power Hook and Loop closures for 360-degree visibility of wearer at all times. The Power Hook and Loop shall be heavy-duty, fluorescent yellow color. The side adjustment pieces shall consist of two horizontal 1” loop pieces sewn the width of the front horizontal trim panel and two 1” x 4.5” hook pieces sewn on the loose adjustable trim portion to attach to the under panel. The size



B. Hats, Ties & Accessories:

1. Unisex Florida Highway Patrol Black 17.5” Necktie

2. Unisex Florida Highway Patrol Black 20” Necktie

adjustment system must allow for a minimum of 24” of adjustment. HVG Pockets and Enhancements:

There shall be an inside pocket on the wearer’s left side utilizing Power Hook and Loop closures so that the safety vest can be stored in the pocket when not in use thus keeping the vest clean. There shall be two silver, retro-reflective microphone tabs, one on each shoulder, measuring 4 ¾” long x 1” wide with a center opening for microphone attachment measuring 1 7/8” wide. There shall also be two pen pockets, one on each side of the vest, measuring 4 ½” long x ¾” wide and made of ANSI 207-2006 compliant lime-yellow tricot. The pen pockets shall be placed on the tricot starting at the top of the side adjustment band and placed closest to the zipper on both sides. The garment shall have a 5-point breakaway Power Hook and Loop breakaway system at the shoulders, sides, and front closure for wearer’s safety.

Fabric: 75% polyester, 25% wool, black Design: Tie is a male 17.5” tie that clips on shirt at neck front. Finishing:

All ties shall finish flat and smooth without visible wrinkles, fabric flaws, stitching, or splicing.

Sizes: One size FHP Unisex 17.5” Black Necktie (Example Image):

Fabric: 75% polyester, 25% wool, black / tan Design: Tie is a male 20” tie that clips on shirt at neck front. 1” tan section at

the bottom of the tie. Finishing: All ties shall finish flat and smooth without visible wrinkles, fabric

flaws, stitching, or splicing. Sizes: One size



3. Unisex Florida Highway Patrol 22”

4. Unisex Black 14” Clip-On Tie

FHP Unisex 20” Necktie (Example Image):

Model: Samuel Broome Style 45053-BLK COO: The Country of Origin shall be USA. Fabric: 75% polyester, 25% wool, black Design: Tie is a male 22” tie that clips on shirt at neck front. Finishing: All ties shall finish flat and smooth without visible wrinkles, fabric

flaws, stitching, or splicing. Sizes: One size FHP Unisex 22” Necktie (Example Image):

Model: Samuel Broome Style 45055 General Description:

The garment shall be a metal clip-on tie.

Features:

• Basic Material: The material shall be 55/45 Polyester/Wool, Tropical Weave. The color shall be black

• Dimensions: The length shall be approximately 14”. The width shall be approximately 3”

• Finishing: All ties shall finish flat and smooth without visible wrinkles, fabric flaws, stitching, or splicing



5. Unisex Florida Highway Patrol Hat Cord (Silver Metallic)

6. Unisex Florida Highway Patrol Hat Cord (Gold Metallic)

7. Florida Highway Patrol Buttons (Gold)

FHP Unisex 14” Clip – On Tie (Example Image):

Fabric: Silver metallic Design: Silver and black hat cord with Silver acorns Sizes: One size FHP Unisex Hat Cord (Silver) (Example Image):

Fabric: Gold metallic Design: Gold and black hat cord with Gold acorns Sizes: One size FHP Unisex Hat Cord (Gold) (Example Image)

Model: Waterbury Style #113980363411907 Design: Button shall be a 24 Ligne gold plated metal button. It shall have a

vertical I back # 34, metal toggle and washer to be supplied with each button.



8. Florida Highway Patrol Buttons (Nickel)

9. Florida Highway Patrol Aviator Ballcap

FHP Button (Gold) (Example Image):

Model: Waterbury, Style # 11398036341190 Design: The button shall be a 24 Ligne silver plated metal button. It shall

have a vertical I back # 34, metal toggle and washer to be supplied with each button.

FHP Button (Nickel) (Example Image):

Model: Flexfit, Style # C855 Fabric: Fabric is 63/24/3 Poly/Cotton Twill/ Spandex, color is black Design: Standard six panel ball cap with button top and rows of stitching on

the bill. Customization:

Option: Cap shall be embroidered with the aviation logo (either ELC275 or ELC898), as shown in the picture below, and provided by the FHP representative. at time of order.

Sizes: S/M: 6 ¾-7 ¼ L/XL: 7 1/8-7 5/8



10. Unisex Florida Highway Patrol Campaign Hat

11. Unisex Florida Highway Patrol Chin Strap

FHP Aviator Ball Cap (Example Images with ELC275 and ELC898 logos):

Model: Stratton Hat Company, Style # S40DB Fabric: 100% straw Design: Hat is lightweight ventilated material of fine imported braids. Brims

shall be twice as dense as the crowns to retain shape. Two separate brims sewn together for strength and shape retention.

Sizes: 6-3/4 through 7-7/8 regular 6-7/8 through 7-1/2 extra long

FHP Unisex Campaign Hat (Example Image):

Model: Stratton Hat Company, Style # ST-3P-BK Fabric: Leather, black Design: Center strap 1/2" wide. Ends are 3/8" wide with snap-type swivel and

closure Sizes: One size FHP Chin Strap (Example Image):



12. Unisex Florida Highway Patrol Black K9 Ball Cap

13. Unisex Florida Highway Patrol Black CIU Ball Cap

Model: Flexfit, Style # C855 Fabric: 63/24/3 Poly/Cotton Twill/ Spandex, color is black Design: Standard six panel ball cap with button top and rows of stitching on

the bill. Sizes: S/M: 6 ¾-7 ¼ L/XL: 7 1/8-7 5/8 Embroidery: Caps shall be embroidered at time of transfer with one of the logos

that will be provided by an FHP representative at time of order. Examples are provided in the pictures below: - Cap No. FL7014 shall receive logo No. ELC197 - Cap No. FL7015 shall receive logo No. ELC196.

FHP K9 Ball Caps (Black) (Example Images with Cap No. FL 7014 and Cap No. FL7015 and logos):

Model: Flexfit, Style # C855 Fabric: 63/24/3 Poly/Cotton Twill/ Spandex, color is black

Design: Standard six panel ball cap with button top and rows of stitching on

the bill.

Customization: Option: Cap shall be embroidered with the aviation logo provided by an FHP representative. An example is provided in the picture below.

Sizes: S/M: 6 ¾-7 ¼ L/XL: 7 1/8-7 5/8 Customization: Add embroidery (No. ELK301) as indicated by an FHP

representative. An example is provided in the picture below:



14. Unisex Black Felt Hat-Honor Guard

15. Unisex Florida Highway Patrol Black Mesh Ball Cap

FHP CIU Ball Cap (Black) (Example image of cap and embroidery No. ELK301):

Model: Stratton Hat Co. Style # F40-BK Fabric: Felt Design: A traditional four dent style. Pressured dye is used and capable of

withstanding 100 hours of Fade-O-Meter testing. The double thick and extra stiff flat brim comes in 3" width. Single vent eyelet located on sides and back.

Sizes: One size *Color image is generic. FHP Unisex Felt Hat Honor Guard (Example Image):

Model: Flexfit Style #C855 Fabric: 63/24/3 Poly/Cotton Twill/ Spandex, color is black Design: Standard six panel ball cap with button top and rows of stitching on

the bill. Customization:

Option: Cap shall be embroidered with the aviation logo, as indicated by an FHP representative at time of order.

Sizes: S/M: 6 ¾-7 ¼ L/XL: 7 1/8-7 5/8 Emblem: Hat shall receive emblem EM3337 in RES as shown in picture below

on center front above visor or FHP in 1 ½” Silver letters



16. Unisex Black 14.5” Clip-On Tie with Button Holes

17. Florida Highway Patrol Large Shoulder Board Saver

FHP Unisex Mesh Ball Cap (Black) (Example Image including emblem EM333):

Model: Samuel Broome Style #45055BLK General Description:

The garment shall be a metal clip-on tie.

Features:

• Basic Material: The material shall be 75/25 Polyester/Wool, Tropical Weave. The color shall be black.

• Dimensions: The length shall be approximately 14.5”. The width shall be approximately 3”.

• Finishing: All ties shall finish flat and smooth without visible wrinkles, fabric flaws, stitching, or splicing.

FHP Unisex 14.5” Clip-On (Example Image):

Model: Vanguard Style # 8422041 Design: Large epaulet shaper. Features:

• Metal • Weighs 0.50 oz.

Sizes: One size



18. Florida Highway Patrol Small Shoulder Board Saver

19. FHP Shoulder Board Large One Gold Stripe

FHP Large Shoulder Board Saver (Example Image):

Model: Vanguard Style #: 8422040 Design: Small epaulet shaper. Features:

• Metal • Weighs 0.25 oz.

Sizes: One size FHP Small Shoulder Board Saver (Example Image):

Model: Vanguard Style # 8240155 Fabric: Black polyester/cotton blend Design: Large black shoulder board that slides over the shirt epaulet. Features:

• One Gold Stripe • Stripe is metallic embroidery thread • Polyester / Cotton Blend • Tapered to fit tapered epaulet

Sizes: One size



20. FHP Shoulder Board Small One Gold Stripe

21. FHP Shoulder Board Large Two Gold Stripes

FHP Large Shoulder Board One (1) Gold Stripe (Example Image):

Model: Vanguard Style # 8240150 Fabric: Black polyester/cotton blend Design: Small black shoulder board that slides over the shirt epaulet. Features:

• One Gold Stripe • Stripe is metallic embroidery thread • Polyester / Cotton Blend • Tapered to fit tapered epaulet

Sizes: One size FHP Small Shoulder Board One (1) Gold Stripe (Example Image):

Model: Vanguard Style # 8240165 Fabric: Black polyester/cotton blend Design: Black shoulder board that slides over the shirt epaulet. Features:

• Two Gold Stripes • Stripes is metallic embroidery thread • Polyester / Cotton Blend • Tapered to fit tapered epaulet

Sizes: One size



22. FHP Shoulder Board Small Two Gold Stripes

23. FHP Unisex Black Badge Mourning Band

FHP Large Shoulder Board Two (2) Gold Stripes (Example Image):

Model: Vanguard Style # 8240160. Fabric: Black polyester/cotton blend Design: Small black shoulder board that slides over the shirt epaulet. Features:

• Two Gold Stripes • Stripes is metallic embroidery thread • Polyester / Cotton Blend • Tapered to fit tapered epaulet

Sizes: One size

FHP Small Shoulder Board Two (2) Gold Stripes (Example Image):

Model: Asheboro Elastics Corporation Style # 050-0822DSA Fabric: Elastic, black color Design: Mourning band is a strip of elastic cut ½” and sewn into a 1-5/8” ring FHP Unisex Badge Mourning Band (Black) (Example Image):



24. Unisex Florida Highway Patrol Rain Hat Cover

C. POLO SHIRTS AND T-SHIRTS:

1. Florida Highway Patrol Unisex Short Sleeve T-Shirt

Model: Premier Emblem P9007, Style # 129 Clear, NPS20155. The item must be made in USA.

Fabric: 100% virgin vinyl, clear Design: Cover for hat, electronically sealed vinyl Features: Protects hats from:

• Rain spots • Re-blocking • Shrinking • Cleaning • Protects hat ribbon

Sizes: S – XL FHP Unisex Rain Cover (Example Image):

Model: S&S, Style # 06500-Black Fabric: 50% Polyester / 50% Cotton, color is black Color: Black Design: Short sleeves rib-knit crew neck band T-shirt. Customization:

As indicated by the FHP representative at the time of order. Examples are provided in the pictures below. EK0136 screen-print on Left Upper Front (pantone color= 428C) EK0137 text (STATE TROOPER) screen-print (pantone color= 428C) on Center Upper Back

Sizes: S-4XL



2. FHP Men Short Sleeve Special Operations Polo

3. FHP Ladies Short Sleeve Special Operations Polo

FHP Unisex Short Sleeve T-Shirt (Example images with EK0136 screen print and EK0137 text):

Model: First Tactical, Style # 112509, Colors 019 Black. 400 Red. Specifications: • 6.5 OZ 100% Polyester Jersey

• Wicking + Anti-microbial finish • Industrial strength melamine buttons

Components:

• Fade, shrink and wrinkle resistant • Saddle shoulder with running side gusset for

maximum movement • Mesh panels under arm for maximum breathability • Traditional 3-button front placket • No roll collar with integrated collar stays • Pen loop on front pocket for easy accessibility • Longer body length without bottom slit stays tucked

in • Bartacks at all stress points • Premium Hardware • UPF 20 • Pen pocket with elastic tethered pocket bag allows

for easy embellishment

Sizes: S-4XL

Model: First Tactical, Style# 122509, Colors 019 Black. Specifications:

• 6.5 OZ 100% Polyester Jersey • Wicking + Anti-microbial finish • Industrial strength melamine buttons

Components: • Fade, shrink and wrinkle resistant

• Saddle shoulder with running side gusset for maximum movement



4. FHP Men Long Sleeve Special Operations Polo

5. FHP Ladies Short Sleeve Special Operations Polo

• Mesh panels under arm for maximum breathability • Traditional 3-button front placket • No roll collar with integrated collar stays • Pen loop on front pocket for easy accessibility • Longer body length without bottom slit stays tucked

in • Bartacks at all stress points • Premium Hardware • UPF 20 • Pen pocket with elastic tethered pocket bag allows

for easy embellishment

Sizes: XS-XXL

Model: First Tactical, Style # 112509, Colors 019 Black. 400 Red. Specifications:


Components: • Fade, shrink and wrinkle resistant • Saddle shoulder with running side gusset for maximum movement • Mesh panels under arm for maximum breathability • Traditional 3-button front placket • No roll collar with integrated collar stays • Pen loop on front pocket for easy accessibility • Longer body length without bottom slit stays tucked in • Bartacks at all stress points • Premium Hardware • UPF 20 • Pen pocket with elastic tethered pocket bag allows for easy

embellishment

Sizes: S-4XL

Model: First Tactical, Style # 121503 colors 019 Black. Specifications:


Components: • Fade, shrink and wrinkle resistant

• Saddle shoulder with running side gusset for maximum movement



D. RANK STRIPES AND INSIGNIAS (IN COLOR):

1. FHP Academy Full Color Emblems

• Mesh panels under arm for maximum breathability • Traditional 3-button front placket • No roll collar with integrated collar stays • Pen loop on front pocket for easy accessibility • Longer body length without bottom slit stays tucked in • Bartacks at all stress points • Premium Hardware • UPF 20 • Pen pocket with elastic tethered pocket bag allows for easy

embellishment

Sizes: XS-XXL

Dimensions & Design:

4” X 4 3/8” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.

Background Material:

Background material is to be 7.5 – 8.0 oz 100% polyester pre-shrunk twill. COLOR: ROYAL BLUE

Thread: All embroidery thread must be 100/2 fast dyed rayon or 90/2 ultra-bright polyester supplied by Robison- Anton Thread Company

Colors:

MERIT GOLD 2463, LT.GOLD 2362, SEAFROST GREEN 2517, ORIENTAL BLUE 2301, BROWN 2478 ROYAL BLUE # 2210, MERIT GOLD 2463, BEIGE 2595

Overlocked Merrow Edge:

The overlocked merrow edge must consist of 300/4 denier polyester thread for the top and two threads of spun polyester for the underneath of the edges. The overlocked merrow edge must be overrun a minimum of 3/8” and the overrun must be securely glued to the back of each emblem. The color of the overlocked merrow edge must be ROYAL BLUE # 2210.

Finishing: An eight-mill polyethylene film sheet must be bonded to the reverse side of the emblems before die cutting. Sufficient heat must be applied to cause the film to melt and bond to the fabric and bobbin threads. The film must be capable of withstanding temperatures in excess of 300 degrees Fahrenheit and must be non-soluble in all commercial laundering fluids.

Workmanship:

All emblems must show a clear-cut execution, be clean, and neatly made. There must be no broken stitches in the emblems. All thread coverage must be complete and acceptable by industry standards.

Embroidering:

Emblems must be machine embroidered on Swiss embroidery looms with automats. Multi-head equipment cannot be used.



2. FHP Round Shoulder Emblem Full Color

FHP Academy (Example Image):


4” ROUND Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.



Thread:

All embroidery thread must be 100/2 fast dyed rayon or 90/2 ultra-bright polyester supplied by Robison- Anton Thread Company.

Colors:

MERIT GOLD 2463, ROYAL BLUE 2210, EMERALD GREEN 2453


The overlocked merrow edge must consist of 300/4 denier polyester thread for the top and two threads of spun polyester for the underneath of the edges. The overlocked merrow edge must be overrun a minimum of 3/8” and the overrun must be securely glued to the back of each emblem. The color of the overlocked merrow edge must be ROYAL BLUE # 2210

Finishing:

An eight-mill polyethylene film sheet must be bonded to the reverse side of the emblems before die cutting. Sufficient heat must be applied to cause the film to melt and bond to the fabric and bobbin threads. The film must be capable of withstanding temperatures in excess of 300 degrees Fahrenheit and must be non-soluble in all commercial laundering fluids.

Workmanship:


Embroidering:




3. FHP Shoulder Emblem Auxiliary Full Color

FHP Round Shoulder (Example Image):


4” X 5” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.



Thread: All embroidery thread must be 100/2 fast dyed rayon or 90/2 ultra-bright polyester supplied by Robison- Anton Thread Company.

Colors: MERIT GOLD 2463, ROYAL BLUE 2210, EMERALD GREEN 2214 Overlocked Merrow Edge:



Workmanship:


Embroidering: Emblems must be machine embroidered on Swiss embroidery looms with automats. Multi-head equipment cannot be used.



4. FHP Sgt. Chevron Full Color Emblems (Large)

FHP Shoulder Auxiliary (Example Image):


2.5” X 2.75” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.


Background material is to be 7.5 – 8.0 oz 100% polyester pre-shrunk twill. COLOR: BLACK


Colors: MERIT GOLD #2463, ROYAL BLUE #2210 Overlocked Merrow Edge:

The overlocked merrow edge must consist of 300/4 denier polyester thread for the top and two threads of spun polyester for the underneath of the edges. The overlocked merrow edge must be overrun a minimum of 3/8” and the overrun must be securely glued to the back of each emblem. The color of the overlocked merrow edge must be ROYAL BLUE # 2210.


Workmanship:



FHP SGT Chevron (LG) (Example Image):



5. FHP Ball Cap Emblem Full Color

6. FHP Cpl. Chevron Full Color Emblems


3” ROUND Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.



Thread:


Colors:





Workmanship:



FHP Ball Cap Emblem (Example Image):

Dimensions & Design: 2.5” X 2.25” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.



7. FHP Shoulder Emblem C.S.O. Full Color



Thread:


Colors:

MERIT GOLD#2463, ROYAL BLUE #2210




Workmanship:


Embroidering:


FHP CPL Chevron (Example Image):

Dimensions & Design: 4” X 5” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.




Colors:




8. FHP Shoulder Emblems Flight Officer Full Color



Finishing:


Workmanship:


Embroidering:

Emblems must be machine embroidered on Swiss embroidery looms with automats. Multi-head equipment cannot be used

FHP Shoulder C.S.O (Example Image):

Dimensions & Design: 4” X 5” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.



Thread:


Colors: MERIT GOLD 2463, ROYAL BLUE 2210, EMERALD GREEN 2214 Overlocked Merrow Edge:


Finishing:

An eight-mill polyethylene film sheet must be bonded to the reverse side of the emblems before die cutting. Sufficient heat must be



9. FHP Sgt. Chevron Full Color (Small) Emblems

applied to cause the film to melt and bond to the fabric and bobbin threads. The film must be capable of withstanding temperatures in excess of 300 degrees Fahrenheit and must be non-soluble in all commercial laundering fluids.

Workmanship:


Embroidering:


FHP Shoulder Flight Officer (Example Image):

Dimensions & Design: 2.5” X 2.75” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.




Colors: MERIT GOLD#2463, ROYAL BLUE #2210 Overlocked Merrow Edge:


Finishing:


Workmanship:


Embroidering:




10. FHP Chevron Trooper Spec. Full Color (Small) Emblems

.

11. FHP Chevron Trooper 1st Class Full Color (Small) Emblems

FHP SGT Chevron (SM) (Example Image):

Dimensions & Design: 2 1/2” X 2 1/8” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.




Colors: MERIT GOLD2463, ROYAL BLUE 2210 Buttonhole Border: The buttonhole BORDER must be ROYAL BLUE 2210 Finishing:

An eight-mill polyethylene film sheet must be bonded to the reverse side of the emblems before die cutting. Sufficient heat must be applied to cause the film to melt and bond to the fabric and bobbin threads. The film must be capable of withstanding temperatures in excess of 300 degrees Fahrenheit and must be non-soluble in all commercial laundering fluids

Workmanship:


Embroidering:


FHP Chevron Troop Spec. (SM) (Example Image):






12. FHP Chevron Senior Trooper Full Color (Small) Emblems


Colors: MERIT GOLD 2463, ROYAL BLUE 2210 Buttonhole Border: The buttonhole BORDER must be ROYAL BLUE 2210 Finishing: An eight-mill polyethylene film sheet must be bonded to the reverse

side of the emblems before die cutting. Sufficient heat must be applied to cause the film to melt and bond to the fabric and bobbin threads. The film must be capable of withstanding temperatures in excess of 300 degrees Fahrenheit and must be non-soluble in all commercial laundering fluids.

Workmanship:


Embroidering:


FHP Trooper 1st Class (SM) (Example Image):

Dimensions & Design: 2 3/16” X 2 1/2” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated

Background Material: Background material is to be 7.5 – 8.0 oz 100% polyester pre-shrunk twill. COLOR: ROYAL BLUE


Colors: MERIT GOLD2463, ROYAL BLUE 2210

Buttonhole Border:

The buttonhole BORDER must be ROYAL BLUE 2210

Finishing:


Workmanship:


Embroidering:




13. FHP Chevron Mst. Trooper Full Color (Small) Emblems

14. FHP Chevron Senior Cpl. Full Color (Small) Emblems

FHP Senior Trooper (SM) (Example Image):




Thread:


Colors: MERIT GOLD2463, ROYAL BLUE 2210 Buttonhole Border: The buttonhole BORDER must be ROYAL BLUE 2210 Finishing:


Workmanship:


Embroidering:


FHP Master Trooper (SM) (Example Image):

Dimensions & Design: 2” X 2 1/2” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.



Thread: All embroidery thread must be 100/2 fast dyed rayon or 90/2 ultra- bright polyester supplied by Robison- Anton Thread Company.



15. FHP Chevron Master Cpl. Full Color (Small) Emblems

Colors: MERIT GOLD 2463, ROYAL BLUE 2210 Buttonhole Border:



Workmanship:


Embroidering:


FHP Senior CPL (SM) (Example Image):





Colors: MERIT GOLD 2463, ROYAL BLUE 2210

Buttonhole Border: The buttonhole BORDER must be ROYAL BLUE 2210 Finishing:


Workmanship:


Embroidering:




16. FHP Chevron Staff Sgt. Full Color (Small) Emblems

17. FHP Chevron Sgt. 1st Class Full Color (Small) Emblems

FHP Master CPL (SM) (Example Image):




Thread:




Workmanship:


Embroidering:


FHP Staff SGT (SM) (Example Image):







18. FHP Chevron Master Sgt. Full Color (Small) Emblems



Workmanship:


Embroidering:


FHP SGT 1st Class (SM) (Example Image):




Thread:




Workmanship:


Embroidering:




19. FHP Chevron Trooper 1ST Class Full Color (Large) Emblems

20. FHP Chevron Senior Trooper Full Color (Large) Emblems

FHP Master SGT (SM) (Example Image):


2 7/8” X 3 3/16” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.




Colors: MERIT GOLD 2463, ROYAL BLUE 2210 Buttonhole Border:



Workmanship:



FHP Trooper 1st Class (LG) (Example Image):





21. FHP Chevron Master Trooper Full Color (Large) Emblems



Thread:


Colors: MERIT GOLD2463, ROYAL BLUE 2210 Buttonhole Border: The buttonhole BORDER must be ROYAL BLUE 2210 Finishing: An eight-mill polyethylene film sheet must be bonded to the reverse


Workmanship:


Embroidering:


FHP Senior Trooper (LG) (Example Image):





Thread:




Workmanship:




22. FHP Chevron Senior CPL. Full Color (Large) Emblems

23. FHP Chevron Master CPL. Full Color (Large) Emblems

Embroidering:


FHP Master Trooper (LG) (Example Image):








Workmanship:



FHP Senior CPL (LG) (Example Image):







24. FHP Chevron Staff SGT. Full Color (Large) Emblems


Colors: MERIT GOLD 2463, ROYAL BLUE 2210 Buttonhole Border: The buttonhole BORDER must be ROYAL BLUE 2210 Finishing:


Workmanship:


Embroidering:


FHP Master CPL (LG) (Example Image):


Background Material: Background material is to be 7.5 – 8.0 oz 100% polyester pre-shrunk twill. COLOR: ROYAL BLUE




Workmanship:


Embroidering:




25. FHP Chevron SGT. 1st Class Full Color (Large) Emblems

26. FHP Chevron Master Sgt. Full Color (Large) Emblems

FHP Staff SGT (LG) (Example Image):








Workmanship:


Embroidering:


FHP SGT 1st Class (LG) (Example Image):








27. FHP Chevron Sgt. of The Patrol Full Color (Large) Emblems

Colors: MERIT GOLD 2463, ROYAL BLUE 2210 Buttonhole Border: The buttonhole BORDER must be ROYAL BLUE 2210 Finishing:


Workmanship:


Embroidering:


FHP MASTER SGT (LG) (Example Image):








Workmanship:


Embroidering:




E. RANK STRIPE AND INSIGNIAS (SUBDUED):

1. FHP Ball Cap Emblem Subdued

2. FHP Shoulder K-9 Emblem Subdued

FHP SGT OF THE PATROL (LG)(Example Image):

Dimensions & Design: 3” ROUND Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.



Thread: All embroidery thread must be 100/2 fast dyed rayon or 90/2 ultra-bright polyester supplied by Robison-Anton Thread Company.

Colors: SILVER GREY 2484, BLACK Overlocked Merrow Edge:

The overlocked merrow edge must consist of 300/4 denier polyester thread for the top and two threads of spun polyester for the underneath of the edges. The overlocked merrow edge must be overrun a minimum of 3/8” and the overrun must be securely glued to the back of each emblem. The color of the overlocked merrow edge must be BLACK.

Finishing:


Workmanship:


Embroidering:


FHP Ball Cap (Example Image):


4” ROUND



3. FHP Shoulder K-9 Emblem Auxiliary

Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.




Colors: SILVER GREY # 2484, BLACK, CLOUD GREY# 2483 Overlocked Merrow Edge:

The overlocked merrow edge must consist of 300/4 denier polyester thread for the top and two threads of spun polyester for the underneath of the edges. The overlocked merrow edge must be overrun a minimum of 3/8” and the overrun must be securely glued to the back of each emblem. The color of the overlocked merrow edge must be BLACK


Workmanship:



FHP Shoulder K-9 (Example Image):


4” X 5” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.




Colors: SILVER GREY # 2484, BLACK Overlocked Merrow Edge:

The overlocked merrow edge must consist of 300/4 denier polyester thread for the top and two threads of spun polyester for the underneath of the edges. The overlocked merrow edge must be overrun a minimum of 3/8” and the overrun must be securely glued to



4. FHP Chevron Trooper Spec Subdued (Large) Emblems

the back of each emblem. The color of the overlocked merrow edge must be BLACK


Workmanship:


Embroidering:


FHP Shoulder Emblem Auxiliary (Example Image):


2 7/8” X 2 ½” Size emblems must measure plus or minus 1/16” of the artwork. All design features must be clearly delineated.




Colors: SILVER GREY # 2484 Buttonhole Border: The buttonhole BORDER must be BLACK Finishing: An eight-mill polyethylene film sheet must be bonded to the reverse


Workmanship:


Embroidering:




5. FHP Chevron Staff Sgt. Subdued (Large) Emblems

6. FHP Chevron Trooper 1st Class (Small) Emblems

FHP Trooper Spec (LG) (Example Image):






Colors: SILVER GREY # 2484 Buttonhole Border: The buttonhole BORDER must be BLACK Finishing:


Workmanship: All emblems must show a clear-cut execution, be clean, and neatly made. There must be no broken stitches in the emblems. All thread coverage must be complete and acceptable by industry standards.

Embroidering:


FHP Staff Sgt (LG) (Example Image):








7. FHP Chevron MST. Trooper Subdued (Small) Emblems

Colors: SILVER GREY # 2484 Buttonhole Border: Finishing:

The buttonhole BORDER must be BLACK An eight-mill polyethylene film sheet must be bonded to the reverse side of the emblems before die cutting. Sufficient heat must be applied to cause the film to melt and bond to the fabric and bobbin threads. The film must be capable of withstanding temperatures in excess of 300 degrees Fahrenheit and must be non-soluble in all commercial laundering fluids.


Embroidering:


FHP Trooper 1st Class (SM) (Example Image):


Background Material: Background material is to be 7.5 – 8.0 oz 100% polyester pre-shrunk twill. COLOR: BLACK




Workmanship:


Embroidering:




8. FHP Chevron SGT. 1ST Class Subdued (Large) Emblems

9. FHP Chevron Sgt. 1ST Class Subdued (Small) Emblems

FHP Master Trooper (SM) (Example Image):








Workmanship:


Embroidering:


FHP Sgt 1st Class (LG) (Example Image):





Thread: All embroidery thread must be 100/2 fast dyed rayon or 90/2 ultra-bright polyester supplied by Robison-Anton Thread Company.



10. FHP Chevron Senior Trooper Subdued (Large) Emblems



Workmanship:


Embroidering:


FHP Sgt 1st Class (SM) (Example Image):






Colors: SILVER GREY # 2484 Buttonhole Border:

The buttonhole BORDER must be BLACK


Workmanship:


Embroidering:


FHP Senior Trooper (LG) (Example Image):



11. FHP Chevron Senior Trooper Subdued (Small) Emblems

12. FHP Chevron MST. SGT. Subdued (Large) Emblems







Workmanship:



FHP Senior Trooper (SM) (Example Image):




Thread: All embroidery thread must be 100/2 fast dyed rayon or 90/2 ultra- bright polyester supplied by Robison- Anton Thread Company.

Colors: SILVER GREY # 2484 Buttonhole Border: The buttonhole BORDER must be BLACK



13. FHP Chevron MST. SGT. Subdued (Small) Emblems

Finishing:



Embroidering:


FHP Master Sgt (LG) (Example Image):








Workmanship:


Embroidering:


FHP Master Sgt (SM) (Example Image):



14. FHP Chevron Trooper Spec. Subdued (Small) Emblems

15. FHP Chevron MST. Trooper Subdued (Large) Emblems








Workmanship:


Embroidering:


FHP Trooper Spec (SM) (Example Image):









16. FHP Chevron Staff SGT. Subdued (Small) Emblems

Workmanship:


Embroidering:


FHP Master Trooper (LG) (Example Image):








Workmanship:


Embroidering:


FHP Staff Sgt (SM) (Example Image):



17. FHP Chevron Trooper 1ST Class Subdued (Large) Emblems

F. GLOVES:

1. Parade Gloves White









Embroidering:


FHP Trooper 1st Class (LG) (Example Image):

Fabric: 100% Cotton, white Design: Standard design dress glove with pin tucking on back and button

closure at the wrist. Features:

• Full inseam with continuous Fourchettes • Closed wrist with white metal snap • Set-in thumb • Three decorative lines on back

FHP Parade Gloves (Example Image):

Available Sizes:



2. Unisex Florida Highway Patrol Ringers Traffic Glove

3. Unisex Florida Highway Patrol Hatch Patrol Gloves

Style # Size Width (± 1/8”) Length (± 3/8”) 99055 Small 3 ¾” 10 ¾” 99056 Medium 3 7/8” 11 1/8” 99057 Large 4” 11 ¼” 99058 X-Large 4 1/8” 11 3/8”

Fabric: 45% Polyester / 44% Nylon / 11% Spandex. Color is reflective orange.

Design: Standard style work glove with elastic wrist and gripper palms Features:

• Reflective strips on palms • Quick pull-on design • Flexible

Sizes:

S - XL

FHP Ringers Traffic Gloves (Example Image):

Style: Shooting Gloves Color: Black Fabric: 50% Aramid, 47% Leather, 3% other fibers Design:

Very lightweight shooting gloves designed for use in Special Weapons and Tactics (SWAT) and tactical operations, with a shorter cuff than standard gloves.

Features:

• Lightweight, comfortable shooting glove • KEVLAR® interlock liner inside of hand and fingers as extra

safeguard • Form-fitting, thin, and durable leather palm for tactility • Short open cuffs for high-performance shooting

Sizes: S – 3XL



FHP Hatch Patrol Gloves (Example Image):

attachment b -exhibit 1 technical specifications …...the entire trouser is to be seamed with...

Documents