Volume 2 • Issue 7 • 1000e116J Biotechnol BiomaterISSN:2155-952X JBTBM an open access journal

Editorial Open Access

Porta et al., J Biotechnol Biomater 2012, 2:7 DOI: 10.4172/2155-952X.1000e116

*Corresponding author: Raffaele Porta, Department of Food Science, University of Naples “Federico II”, Portici, Napoli, Italy, Tel: +6013-2101647; Fax: +606-7987010; E-mail: portaraf@unina.it

Received October 25, 2012; Accepted October 25, 2012; Published October 27, 2012

Citation: Porta R, Mariniello L, Pierro PD, Sorrentino A, Giosafatto VC (2012) Water Barrier Edible Coatings of Fried Foods. J Biotechnol Biomater 2:e116. doi:10.4172/2155-952X.1000e116

Copyright: © 2012 Porta R, et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Water Barrier Edible Coatings of Fried Foods

Department of Food Science, University of Naples “Federico II”, Portici, Napoli, Italy

Food deep frying induces several changes in both chemical and physical properties of the different components, including protein denaturation, starch gelatinization, water vaporization and crust formation [2,3], and foods normally absorb great amounts of oil during cooking. Thus, during the last ten years, there has been an increased interest in the scientific community to investigate new ways to reduce fat uptake by foods during frying. In fact, high oil content associated with many different diet products is indicated to be one of the most significant cause of high blood cholesterol level and pressure, and as a consequence of the increased incidence of both obesity and coronary heart diseases [4-6]. To this aim, health authorities as well as mass media advise of the desirability to decrease the proportion of fat in the average diet, and to develop food products containing low fat content. As oil uptake is the major nutritional critical point of deep frying, reaching in some cases even half of the total weight of the product [7,8], the main challenge in this field appears to realize a frying process improvement by controlling and lowering the final fat content of different foods subjected to such cooking procedure [9].

Deep fat frying is a process of heating and drying of food through the contact of the latter with oil at high temperature (170-210°C). The process involves simultaneous heat and mass transfer because heat transferred from oil into food determines the evaporation of the internal product moisture [10]. This phenomenon results in the formation of a capillary trail, increasing the porosity of the fried food and allowing oil to enter into the internal sections of the product, during both its frying and its cooling after frying (Figure 1A) [10,11]. Native moisture is an important attribute of food material influencing oil uptake. Elevated water content, in fact, leads to a higher water loss by food during frying, consequently producing in it a greater number of pores that facilitate oil penetration [12]. These transferring processes are well correlated and respond to kinetic models for moisture loss and oil uptake, previously described for either breaded or differently coated products [1,11-18]. Ngadi et al. [19] effectively decreased fat uptake by chicken nuggets by just reducing original water content precooking samples in microwave, whereas air drying pretreatment for reducing moisture was the successful method described by Krokida et al. [16], for lowering oil uptake by potato products.

Several approaches have been proposed so far for reducing fat absorption during frying. It is well known that often foods-especially

A. Uncoated fried food

B. Coated fried food

Water Oil

InOut

InOut

Figure 1: Internal sections of the product during its frying and cooling after frying in case of A) Uncoated fried food B) Coated fried food.

Raffaele Porta*, Loredana Mariniello, Angela Sorrentino, Valeria C.L. Giosafatto, Giovanna Rossi Marquez, Marilena Esposito and Prospero Di Pierro

Frying is known as one of the oldest food cooking processes dating back as early as sixteen centuries B.C., being still widespread utilized today at both domestic and industrial scale, because of its ability to enhance flavour and texture of numerous foods. Fried products are appreciated everywhere because of their improved palatability [1], consumers generally like eating foods with soft core and crispy surface, even though significant geographical differences exist due to the different raw material availability and the multiple cultural habits. Nowadays, they occur in the traditional cuisines of practically every part of the world. Furthermore, also several mass consumption products have fried versions, and worldwide fast food companies provide every day literally tons of fried foods, such as french fries, doughnuts, chicken, onion rings, etc.

fish, poultry, cheese, and vegetables-are coated by breading [20,21]. Food science research tries to prevent high fat absorption by testing different coating procedures, such as the application of edible films to food products prior to frying. This procedure also represents an alternative method for avoiding changes in the quality, as well as sensory properties of food, and for increasing its texture [22-24]. The use of edible films was proposed in the late sixties, originally to extend the shelf life of meat and later on to improve the quality of various fresh, frozen and manufactured food items. The main function that an edible film is able to perform is to hinder moisture migration, and this effect is mostly important for maintaining optimum quality in multi-phase foods [25]. Therefore, edible coatings can be effective also to decrease fat absorption and frying loss (Figure 1B) [26,27], although product

Jour

nal o

f Biot

echnology &Biomaterials

ISSN: 2155-952X

Journal of Biotechnology & Biomaterials

Citation: Porta R, Mariniello L, Pierro PD, Sorrentino A, Giosafatto VC (2012) Water Barrier Edible Coatings of Fried Foods. J Biotechnol Biomater 2:e116. doi:10.4172/2155-952X.1000e116

Page 2 of 3

Volume 2 • Issue 7 • 1000e116J Biotechnol BiomaterISSN:2155-952X JBTBM an open access journal

valuable experimental data devoted to create simple processes using hydrocolloid coatings for different fried foods and responding to the real-life needs, are strongly desirable.

References

1. Moyano PC, Pedreschi F (2006) Kinetics of oil uptake during frying of potato slices: effect of pre-treatments. LWT - Food Science and Technology 39: 285-291.

8. Mellema M (2003) Mechanism and reduction of fat uptake in deep-fat fried foods. Trends Food Sci Technol 14: 364-373.

9. Ziaiifar AM, Achir N, Courtois F, Trezzani I, Trystram G (2008) Review of mechanisms, conditions, and factors involved in the oil uptake phenomenon during the deep-fat frying process. Int J Food Sci Technol 43: 1410-1423.

10. Irudayaraj J (2001) Food Processing Operations Modeling: Design and Analysis. Marcel Dekker Inc, New York.

11. Duran M, Pedreschi F, Moyano P, Troncoso E (2007) Oil partition in pre-treated potato slices during frying and cooling. J Food Eng 81: 257-265.

12. Pinthus EJ, Weinberg P, Saguy IS (1993) Criterion for oil uptake during deep-fat frying. J Food Sci 58: 204–205.

13. Akinbode AA, Michael ON, Raghavan GSV (2009) Kinetics of mass transfer in microwave precooked and deep-fat fried chicken nuggets. J Food Eng 91: 146-153.

14. Krokida MK, Oreopoulou V, Maroulis ZB (2000) Effect of frying conditions on shrinkage and porosity of fried potatoes. J Food Eng 43: 147-154.

15. Krokida MK, Oreopoulou V, Maroulis ZB, Marinos-Kouris D (2001) Deep fat frying of potato strips-quality issues. Drying Technology: An International Journal 19: 879-935.

16. Krokida MK, Oreopoulou V, Maroulis ZB, Marinos-Kouris D (2001) Effect of pre-drying on quality of French fries. J Food Eng 49: 347-354.

17. Lee JS, Kim BK, Kim KH, Park DJ (2008) Preparation of low-fat uptake doughnut by dry particle coating technique. J Food Sci 73: E137- E142.

18. Troncoso E, Pedreschi F (2009) Modeling water loss and oil uptake during vacuum frying of pre-treated potato slices. LWT-Food Science and Technology 42: 1164-1173.

19. Ngadi MO, Wang Y, Adedeji AA, Raghavan GSV (2009) Effect of microwave pretreatment on mass transfer during deep-fat frying of chicken nugget. LWT- Food Science and Technology 42: 438-440.

20. Antonova I, Mallikarjunan P, Duncan SE (2003) Correlating objective measurements of crispness in breaded fried chicken nuggets with sensory crispness. J Food Sci 68: 1308-1315.

21. Dogan SF, Sahin S, Sumnu G (2005) Effects of soy and rice flour addition on batter rheology and quality of deep-fat fried chicken nuggets. J Food Eng 71: 127-132.

22. Amboon W, Tulyathan V, Tattiyakul J (2012) Effect of Hydroxypropyl Methylcellulose on Rheological Properties, Coating Pickup, and Oil Content of Rice Flour-Based Batters. Food and Bioprocess Technology 5: 601-608.

23. Cutter CN (2006) Opportunities for bio-based packaging technologies to improve the quality and safety of fresh and further processed muscle foods. Meat Sci 74: 131-142.

quality in this case is strictly affected by the frying time and physical-chemical characteristics of the used coating material [28].

methylcellulose, pectins, alginate, carrageenan and various gums, but also several proteins and lipids have been analyzed with different advantages and disadvantages, as oil barrier coating materials of a variety of foods over the past twenty five years [4,8,23,25,29,34-55]. Hydrocolloid films are usually applied in liquid form by dipping or spraying the food item or part of it, using a solution or a dispersion of the polymer(s). To achieve a continuous layer of film, the solvent is afterwards eliminated through thermal treatment or irradiation. Both the composition of the film-forming mixture and the environmental conditions (temperature, humidity, etc.) markedly influence the coating features [25,43,56]. Uniformity of thickness of the barrier, as well as porosity and permeability of the latter are strictly dependent on its flexibility and cohesive strength. Furthermore, it is noteworthy that different foods show different responses to the same type of coating material. In fact, whether surface roughness generally represents a critical factor in oil absorption by all kind of foods, other food-related characteristics such as crust microstructure may explain the specific behaviour of the different product categories [57]. In particular, in the case of frying applications, the integrity of the coating strictly depends on the product, since many foods are known to increase their volume and to change their shape, during and after frying. The addition of plasticizers as sorbitol, glycerin or other agents, almost always facilitates the formation of an effective coating at high temperatures [58].

In conclusion, even though hydrocolloid coatings have shown to effectively alter the water-holding capacity of a variety of fried foods by trapping moisture inside and preventing the replacement of water by oil, most of the studies provided results limited to the food oil content, and rarely investigated the correlation between heat/mass transfer and fat uptake. In addition, it would be desirable that future investigations will include rigorous sensory analysis of the final products, since unfortunately, the existing literature includes only descriptive results or hedonic tests carried out generally with a small number of consumers. Also for these reasons, despite the numerous laboratory researches and the potential market for reduced-fat food production, there have been so far only few applications of this technique in industry. Hence, further

2. Mallikarjunan P, Chinnan MS, Balasubramaniam VM, Phillips RD (1997) Edible coating for deep-fat frying of starchy products. LWT-Food Science and Technology 30: 709-714.

3. Rimac-Brncic S, Lelas V, Rade D, Simundic B (2004) Decreasing of oil absorption in potato strips during deep fat frying. J Food Eng 64: 237-241.

4. Albert S, Mittal GS (2002) Comparative evaluation of edible coatings to reduce fat uptake in a deep-fried cereal product. Food Res Int 35: 445-458.

5. Gutiérrez-Lopez GF, Barbosa-Cánovas GV, Welti-Chanes J, Parada-Arias E (2008) Food Engineering: Integrated Approaches. Springer, New York.

6. Shih FF, Bett-Garber KL, Daigle KW, Ingram D (2005) Effects of rice batter on oil uptake and sensory quality of coated fried okra. J Food Sci 70: S18-S21.

7. Freitas, DDGC, Berbari, SAG, Prati P, et al. (2009) Reducing fat uptake in cassava product during deep-fat frying. J Food Eng 94: 390-394.

Different film ingredients and additives have been tested with the aim to reduce the amount of oil absorbed by fried food, and several coating and batter formulations using various types of biopolymers have been patented [8]. Among these, hydrocolloids are the main category of functional agents that have been used for the past forty years [29]. Hydrocolloids are defined as water-soluble polymers, able to confer viscosity and gelate aqueous system retaining water in food systems [30]. They are extensively used in numerous food and beverage products, mostly as thickening, gelling, stabilizing and emulsifying agents. But in addition, hydrocolloids were shown to play an additional role in fried food development by forming on their own a fine invisible coating, able to prevent excessive oil absorption during the frying process. Thus, they are gaining an increasing interest also as food coatings for their barrier properties to gas/moisture, and their satisfying mechanical features [31]. Because these polymers are highly hydrophilic, they present only a limited permeability to moisture, whereas they behave as very effective oxygen and carbon dioxide barriers and protect against lipid oxidation [25]. Thus, a variety of foods have been tested after their surface modification by hydrocolloid coatings to prevent moisture loss, to extend their shelf-life, and also to reduce oil uptake during frying [8,32,33].

Not only polysaccharides, such as hydroxypropylcellulose,

Citation: Porta R, Mariniello L, Pierro PD, Sorrentino A, Giosafatto VC (2012) Water Barrier Edible Coatings of Fried Foods. J Biotechnol Biomater 2:e116. doi:10.4172/2155-952X.1000e116

Page 3 of 3

Volume 2 • Issue 7 • 1000e116J Biotechnol BiomaterISSN:2155-952X JBTBM an open access journal

24. Gennadios A, Hanna MA, Kurth LB (1997) Application of edible coatings on meats, poultry and seafoods: a review. LWT - Food Science and Technology 30: 337-350.

25. Kester JJ, Fennema OR (1986) Edible films and coatings: a review. Food Tech 40: 47-59.

26. Akdeniz N, Sahin S, Sumnu G (2006) Functionality of batters containing different gums for deep-fat frying of carrot slices. J Food Eng 75: 522-526.

27. Debnath S, Bhat KK, Rastogi NK (2003) Effect of pre-drying on kinetics of moisture loss and oil uptake during deep fat frying of chickpea flour-based snack food. LWT- Food Science and Technology 36: 91-98.

28. Kilincceker O, Hepsag F (2012) Edible coating effects on fried potato balls. Food and bioprocess technology 5: 1349-1354.

29. Varela P, Fiszman SM (2011) Hydrocolloids in fried foods. A review. Food Hydrocoll 25: 1801-1812.

30. Sahin S, Sumnu SG (2008) Advances in deep-fat frying of foods. Taylor & Francis Group, New York, USA.

31. Krochta JM., Baldwin EA, Nisperos-Carriedo M (1994) Edible coatings and films to improve food quality. Taylor & Francis Group, New York, USA.

32. Hershko V, Nussinovitch A (1998) The behavior of hydrocolloid coatings on vegetative materials. Biotechnol Prog 14: 756-765.

33. Kampf N, Nussinovitch A (2000) Hydrocolloid coating of cheeses. Food Hydrocoll 14: 531-537.

34. Ang JF (1993) Reduction of fat in fried batter coatings with powdered cellulose. J Am Oil Chem Soc 70: 619-622.

35. Garcıa MA, Ferrero C, Bertola N, Martino M, Zaritzky N (2002) Edible coatings from cellulose derivatives to reduce oil uptake in fried products. Innov Food Sci Emerg Technol 3: 391-397.

36. Chen HH, Kang HY, Chen SD (2008) The effects of ingredients and water content on the rheological properties of batters and physical properties of crusts in fried foods. J Food Eng 88: 45-54.

37. Dragich AM, Krochta JM (2010) Whey protein solution coating for fat-uptake reduction in deep-fried chicken breast strips. J Food Sci 75: S43-S47.

38. Duxbury DD (1989) Oil water barrier properties enhanced in fried foods. Food Proc 50: 66-67.

39. Fiszman SM, Salvador A (2003) Recent developments in coating batters. Trends Food Sci Technol 14: 399-407.

40. Garmakhany AD, Mirzaei HO, Nejad MK, Maghsudlo Y (2008) Study of oil uptake and some quality attributes of potato chips affected by hydrocolloids. Eur J Lipid Sci Technol 110: 1045-1049.

42. Greener IK, Fennema O (1989) Barrier properties and surface characteristics of edible, bilayer films. J Food Sci 54: 1393-1399.

43. Phillips GO, Williams PA (1988) Gums and stabilizers for the food industry.Volume 4, IRL Press, UK.

44. Huse HL, Mallikarjunan P, Chinnan MS, Hung YC, Phillips RD (1998) Edible coatings for reducing oil uptake in production of Akara (deep-fat frying of cowpea paste). J Food Process Preserv 22: 155-165.

45. Ilter S, Dogan IS, Meral R (2008) Application of food grade coatings to turkey buttocks. Ital J Food Sci 20: 203-212.

46. Kim DN, Lim J, Bae IY, Lee HG, Lee S (2011) Effect of hydrocolloid coatings on the heat transfer and oil uptake during frying of potato strips. J Food Eng 102: 317-320.

47. Krochta JM, Mulder-Johnston C (1997) Edible and biodegradable polymer films: challenges and opportunities. Food Tech 51: 60-74.

48. Martin ML, Davis AB (1986) Effect of soy flour on fat absorption by cake donuts. Cereal Chem 63: 252-255.

49. Nasiri FD, Mohebbi M, Yazdi FT, Khodaparast MHH (2012) Effects of soy and corn flour addition on batter rheology and quality of deep fat-fried shrimp nuggets. Food and Bioprocess Technology 5: 1238-1245.

50. Rayner M, Ciolfi V, Maves B, Stedman P, Mittal GS (2000) Development and application of soy-protein films to reduce fat intake in deep-fried foods. J Sci Food Agric 80: 777–782.

51. Salvador A, Sanz T, Fiszman SM (2008) Performance of methyl cellulose in coating batters for fried products. Food Hydrocoll 22: 1062-1067.

52. Sanz T, Fernandez MA, Salvador A, Munoz J, Fiszman SM (2005) Thermogelation properties of methylcellulose (MC) and their effect on a batter formula. Food Hydrocoll 19: 141-147.

53. Singthong J, Thongkaew C (2009) Using hydrocolloids to decrease oil absorption in banana chips. LWT-Food Science and Technology 42: 1199-1203.

54. Skurtys O, Acevedo C, Pedreschi F, Enronoe J, Osorio F, et al. (2010). Food hydrocolloid edible films and coatings. Nova Publishers, New York.

55. Williams R, Mittal GS (1999) Water and fat transfer properties of polysaccharide films on fried pastry mix. LWT-Food Science and Technology 32: 440-445.

56. Soorgi M, Mohebbi M, Mousavi SM, Shahidi F (2012) The effect of methylcellulose, temperature, and microwave pretreatment on kinetic of mass transfer during deep fat frying of chicken nuggets. Food and Bioprocess Technology 5: 1521-1530.

57. Moreno MC, Brown CA, Bouchon P (2010) Effect of food surface roughness on oil uptake by deep-fat fried products. J Food Eng 101: 179-186.

58. Tavera-Quiroz MJ, Urriza M, Pinotti A, Bertola N (2012) Plasticized methylcellulose coating for reducing oil uptake in potato chips. J Sci Food Agric 92: 1346-1353.

41. Bajaj I, Singhal R (2007) Gellan gum for reducing oil uptake in sev, a legume based product during deep-fat frying. Food Chemistry 104: 1472-1477.