b08 ovjesna oprema za optiku.pdf

B8/8 Introduction

Metalfree (ADSS cables) and metal-armored (OPGW, OPPW) aerial cables with integrated optical fibres (called optical fibre aerial cables) are used to transmit information. The information is transmitted by means of modulated light pulses in the interior of the thin optical fibres. These fibres have a total diameter of approx. 300 m. The optical fibre aerial cables can be stressed upto a limited tensile force without any increase of the optical signal damping in the fibres. However, in the case of a radial force, the optical damping will increase by bounds. This increase can lead to a reduction of the information flow through the fibres.

The fibres with an additional length are beded in one or several relatively rigid coaxial tubes to avoid inadmissible stress. In the case of metalfree optical cables the tubes are beded in a supporting structure of aramid fibres. The optical fibre cable is finally covered with an extruded PE-mantle. The core of the metall-armored aerial cable is covered with one or more layers of Aluminium wires, Aluminium alloy wires or Aluminium-clad steel wires. As the optical fibres have to be protected against inadmissible radial forces during and after the installation of optical fibre aerial cables the fittings at the tension-, suspension- and fixing points have to meet special requirements. For common conductors and ground wire we use fittings for tension and suspension points which provoke the necessary grippage force by effecting of a high radial force (for example wedge type tension clamp, suspension clamp). Due to the high pressure sensitivity of optical fibres beded in the aerial cable these types of fittings are not suitable for optical fibre aerial cables. The fittings of the RIBE-Optofit-program are designed regarding this high pressure sensitivity. The fittings are especially adapted to this purpose. The induced radial forces are spread over a larger contact surface (for example dead end) in such a way that the fibres are not inadmissibly stressed and the necessary grippage forces are achieved. It is impossible to determine standardized accessories for optical fibre aerial cables as the structure of the different cables is very manifold. Fittings for optical fibre aerial cables mainly consist of the following group of fittings: - Helically formed fittings for tension and suspension points - Earth connections - Tower down-lead accessories - Vibration dampers Helically formed fittings form the major part of accessories for optical fibre aerial cables. They are composed of helically formed rods which - according to the respective application - are separate or preassembled, straight or bended on delivery. Helically formed accessories can be used to tension, to suspend or to connect conductors, optical fibre aerial cables, glass fibre rods and solid rods such as guys. In addition, helically formed accessories are used for protection or repair of conductors or optical fibre aerial cables, for attachment to post insulators and for tensioning of street lighting. Helically formed accessories have been used very succesfully since 1950. The application of helically formed accessories is not at all limited to overhead lines. Helically formed accessories are also used to a large extent for the construction of antennae, radar stations etc.

The principle of operation of helically formed accessories is based on the principle of the development of a low pressure over a large area. The inside diameter of the unloaded helical rods is slightly smaller than the outside diameter of the conductor, optical fibre aerial cable or solid rod. By wrapping the helical rods on a conductor or optical fibre aerial cable, a spring tension is created, producing the necessary frictional contact. This spring tension is elastic and ensures a constant grip. To ensure the full performance, helically formed accessories must exactly be adapted to the outside diameter of conductor, optical fibre aerial cable or solid rod. In general, helically formed accessories are made of a material similar to that of conductor, optical fibre aerial cable or solid rod. Usually this garanties a similar corrosion resitivity.

Installation of helically formed accessories can be done without any tools. Installation faults are nearly impossible. Mounting instructions are available on demand. Helically formed accessories are largely protected by patents or registration of designs. If helically formed accessories are required for applications other than those included in this catalogue, a specific inquiry is requested.

The RIBE numbers of helically formed accessories start with a combination of letters that is followed by six figures and possibly letters added at the end. for example: AG 089 077

The respective letters or figures have the following meaning:

1) Starting letters The first capital letter and in some cases the first and the second letter designate the respective type. A - Dead ends B - Spacers D - Vibration dampers J - Insulator ties

Stand: 19. Juni 2006Pfad: Optofit/General/ Introduction/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

1 / 117

L - Line guards LT - Suspension grips M - Bird flight diverters (star) R, UR, UT - Protection rods S - Armor rods T - Suspension rods V - Line splices Z - Bird flight diverters (spring)

The last capital letter and in some cases also the before last designate the material. A - Aluminium alloy B - Bronze G - Steel, h.d.g. H - Stainless steel K - Copper alloy P - Plastic material S - Other material combinations V - Copper-clad steel W - Aluminium-clad steel

2) Six figures The six figures of the RIBE number shall be considered as two groups, three figures each. The first group gives by pointing off the last figure the largest possible cable diameter for which the accessory is suitable (measurement: mm). The second group indicates the overall length of accessory in cm.

3) Letters added to the RIBE number The letters added to the RIBE number refer to special applications or the nature of the accessory. The respective letters have the following meaning: H - Suitable for post insulator with neck L - Suitable for "Lngsbund" type insulator M - Suitable for "Mittelbund" type insulator li - Left hand outer lay accessory s - Special design

Stand: 19. Juni 2006Pfad: Optofit/General/ Introduction/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

2 / 117

B8/9 Suspension arrangement

Suspension arrangement for OPGW (schematic representation)

1 ..... OPGW 2 ..... Tower 3 ..... C-shaped support 4 ..... Armour grip suspension 5 ..... Vibration damper 6 ..... Shunt (optional)

Suspension arrangement for thin ADSS cable (schematic representation)

1 ..... ADSS cable 2 ..... Shackle 3 ..... Armour grip suspension 4 ..... Vibration damper

Stand: 26. Juni 2006Pfad: Optofit/General/ Suspension arrangement/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

3 / 117

B8/10 Tension arrangement

Tension arrangement with OPGW passing the tower (schematic representation)

1 ...... OPGW 2 ...... Tower 3 ...... Tension support 4 ...... Pair of straps 5 ...... Twisted double eye 6 ...... Thimble 7 ...... Helical dead end 8 ...... Protection rods 9 ...... Vibration damper 10 .... Parallel groove clamp 11 .... Shunt

Tension arrangement with ADSS cable passing the tower (schematic representation)

1 ..... ADSS cable 2 ..... Wooden pole 3 ..... Hook 4 ..... Helical dead end

Tension arrangement with OPGW at the tower with joint box (schematic representation)

Stand: 17. Mai 2006Pfad: Optofit/General/ Tension arrangement/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

4 / 117

1 ...... OPGW 2 ...... Tower 3 ...... Tension support 4 ...... Pair of straps 5 ...... Twisted double eye 6 ...... Thimble 7 ...... Helical dead end 8 ...... Protection rods 9 ...... Vibration damper 10 .... Parallel groove clamp 11 .... Shunt 12 .... Fixing clamp 13 .... Filler bolt

Tension arrangement with ADSS cable at the tower with joint box (schematic representation)


ONLINE-CATALOGUE

5 / 117

1 ..... ADSS cable 2 ..... Tower 3 ..... Hook 4 ..... Thimble 5 ..... Helical dead end


ONLINE-CATALOGUE

6 / 117

B8/11 String accessories for tower attachment of self supporting optical fibre aerial cables

Variant A of tower attachment

Variant B of tower attachment

Variant C of tower attachment

Stand: 17. Mai 2006Pfad: Optofit/General/ String accessories for tower attachment of self supporting optical fibre aerial cables/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

7 / 117

1 ...... Vertical tension hinge 2 ...... Turnbuckle (eye - eye) 3 ...... Turnbuckle (clevis - eye) 4 ...... Straight clevis eye 5 ...... Adjustable clevis eye 6 ...... Twisted double eye 7 ...... Twisted clevis eye 8 ...... Straight clevis eye 9 ...... Pair of straps 10 .... Horizontal U-bolt 11 .... Shackle 12 .... Horizontal tension hinge 13 .... Tower 14 .... Tension support 15 .... Protection rods 16 .... Thimble 17 .... Dead end

Remark: Detail informations of string accessories contain the RIBE-catalogue "Insulator string hardware".

Stand: 17. Mai 2006Pfad: Optofit/General/ String accessories for tower attachment of self supporting optical fibre aerial cables/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

8 / 117

B800/0 Introduction to armour grip suspensions

Design and performance: The armour grip suspension is used for the movable suspension of conductors and optical fibre aerial cables on suspension towers.

Material:

The armour grip suspension is composed of a certain number of helically formed rods, a concave Neoprene insert consisting of two halfs and a clamp body. The helical rods are placed on the Neoprene insert at the suspension point. This centre assembly is fixed by the clamp body which due to positive locking prevents axial displacement of the conductor. The armour grip suspension - like the application of suspension clamps along with armour rods - does not impede asymmetric vibration and thus avoids local alternating bending stress. This is no static compression force existing in standard suspension clamps with and without armour rods due to the keeper with bolts. This is the principle difference of the armour grip suspension compared to suspension equipments commonly used up to now. The reinforcement of the cross-section by armor rods improves the lifetime of the vibrating conductor/ optical fibre aerial cable. However, it is no damping device to cope with conductor vibrations. The electrical connection of the helical rods and the suspension equipment is resistant to short-circuit current, i.e. it is capable to conduct the short circuit current of a conductor/ optical fibre aerial cable without damage.

Helical rods and clamp bodies are made of high-tensile, corrosion-resistant aluminium alloy, inserts of Neoprene, straps and threaded bolts of hot-dip galvanized steel.

Installation: The Neoprene composed of two concave halves is placed on the conductor/ optical fibre aerial cable at the suspension point and attached by the helical rods which are wrapped on the conductor/ optical fibre aerial cable with insert. The clamp body of the suspension equipment is placed on either side of the centre assembly thus that is embraced by the clamp body. The clamp body is attached by application of a bolt. Apart from a tubular hexagon box spanner, no special tooling is required for assembly. The assembly has to be performed in accordance with RIBE-Mounting Instruction No. 10.

Stand: 10. August 2006Pfad: Optofit/ Suspension fittings/ Introduction to armour grip suspensions/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

9 / 117

B801/1 Armour grip suspensions for self supporting optical fible aerial cables (without shunt attachment)

1 ..... Clamp body with neoprene-insert 2 ..... Helical rods 3 ..... Fig. 1 4 ..... Fig. 2 5 ..... Bolt 1

LTA 097 180/17 9,0 -9,7 B 801 006 KA 097 180 s 8 1,8 LTA 104 180/5 9,8 -10,4 (Fig. 1) KA 104 180 s 9 1,8 LTA 111 180/6 10,5 -11,1 KA 111 180 s 10 1,8 LTA 118 180/9 11,2 -11,8 KA 118 180 s 1800 4,24 10 76 82 M 8x35 13 1,9 16 40 LTA 125 180/10 11,9 -12,5 KA 125 180 s 10 1,9 LTA 131 180/11 12,6 -13,1 KA 131 180 s 11 2,0 LTA 137 180/12 13,2 -13,7 KA 137 180 s 11 2,0

LTA 144 180 13,8 -14,4 F 13 108 KA 144 180 s 1800 11 2,4 LTA 149 180 14,5 -14,9 (Fig. 1) KA 149 180 s 1800 11 2,4 LTA 157 180 15,0 -15,7 KA 157 180 s 1800 4,62 11 89 84 M 8x35 13 2,5 22 90 LTA 161 200 15,8 -16,1 KA 161 200 s 2000 12 2,6 LTA 165 200 16,2 -16,5 KA 165 200 s 2000 12 2,6

LTA 172 200 16,6 -17,2 F 2787 KA 172 200 s 11 3,4 LTA 179 200 17,3 -17,9 (Fig. 2) KA 179 200 s 2000 5,18 12 96 105 M 10x42 17 3,5 27 90 LTA 186 200 18,0 -18,6 KA 186 200 s 12 3,5 LTA 193 200 18,7 -19,3 KA 193 200 s 12 3,5

LTA 203 200 19,4 -20,3 F 2698 KA 203 200 s 2000 11 4,6 LTA 213 200 20,4 -21,3 (Fig. 2) KA 213 200 s 2000 6,35 11 115 115 M 10x45 17 4,6 28 90 LTA 222 200 21,4 -22,2 KA 222 200 s 2000 12 4,7 LTA 231 220 22,3 -23,1 KA 231 220 s 2200 12 5,0

LTA 237 220 23,2 -23,7 F 2789 KA 237 220 s 2200 12 5,9 LTA 243 220 23,8 -24,3 (Fig. 2) KA 243 220 s 2200 6,35 13 127 136 M 12x55 19 6,1 27 85 LTA 249 240 24,4 -24,9 KA 249 240 s 2400 13 6,3 LTA 256 240 25,0 -25,6 KA 256 240 s 2400 13 6,3

LTA 265 240 25,7 -26,5 F 2730 KA 265 240 s 2400 11 8,6 LTA 274 250 26,6 -27,4 (Fig. 2) KA 274 250 s 2500 11 8,7 LTA 283 250 27,5 -28,3 KA 283 250 s 2500 7,87 12 140 145 M 12x55 19 9,1 40 150 LTA 292 250 28,4 -29,2 KA 292 250 s 2500 12 9,2 LTA 299 300 29,3 -29,9 KA 299 300 s 3000 12 9,9 LTA 306 300 30,0 -30,6 KA 306 300 s 3000 12 10,0

LTA 311 300 30,70 -31,14 F 2792 KA 311 300 s 11 LTA 317 300 31,15 -31,74 (Fig. 2) KA 317 300 s 11

RIBE-Order-No. Clamping range RIBE-No. Helical rods a b Bolt 1 Mass/ Ith FN(1+2) Clamp+Neoprene- Ribe-No. L No. of rods Size s pcs

mm Insert (1) mm mm mm mm mm kg kA kN

Stand: 06. November 2008Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (without shunt attachment)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

10 / 117

LTA 326 300 31,75 -32,66 KA 326 300 s 3000 9,27 12 150 200 M 12x55 19 13,0 40 150 LTA 333 300 32,67 -33,37 KA 333 300 s 12 LTA 344 300 33,38 -34,43 KA 344 300 s 12

s - Width across flats



Material: Helical rods: Aluminium alloy Clamp body: Aluminium alloy Straps: Steel, h.d.g. Bolt: Steel, h.d.g. Insert: Neoprene

Application: See data-sheet B800

Remarks:

For other executions please inquire.

For installation follow RIBE-Mounting Instruction No. 10. All mentioned armour grip suspensions are available with left-hand lay direction on request (order example: LTA 172 200 lis).

Stand: 06. November 2008Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (without shunt attachment)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

11 / 117

B801/2 Armour grip suspensions for self supporting optical fible aerial cables (with shunt attachment)

1 ..... Clamp body with neoprene-insert 2 ..... Helical rods 3 ..... Fig. 1 4 ..... Fig. 2 5 ..... Attachment for shunts 6 ..... Bolt 1

LTA 097 180/18 9,0 -9,7 B 801 006 KA 097 180 s 8 LTA 104 180/7 9,8 -10,4 (Fig. 1) KA 104 180 s 9 LTA 111 180/8 10,5 -11,1 KA 111 180 s 10 LTA 118 180/12 11,2 -11,8 KA 118 180 s 1800 4,24 10 76 82 M 8x35 13 1,8 16 40 LTA 125 180/14 11,9 -12,5 KA 125 180 s 10 LTA 131 180/15 12,6 -13,1 KA 131 180 s 11 LTA 137 180/16 13,2 -13,7 KA 137 180 s 11

LTA 144 180/6 13,8 -14,4 F 13 108 KA 144 180 s 1800 11 2,1 LTA 149 180/7 14,5 -14,9 (Fig. 1) KA 149 180 s 1800 11 2,1 LTA 157 180/8 15,0 -15,7 KA 157 180 s 1800 4,62 11 89 84 M 8x35 13 2,2 22 90 LTA 161 200/9 15,8 -16,1 KA 161 200 s 2000 12 2,4 LTA 165 200/10 16,2 -16,5 KA 165 200 s 2000 12 2,4

LTA 172 200/5 16,6 -17,2 F 2787 KA 172 200 s 11 LTA 179 200/6 17,3 -17,9 (Fig. 2) KA 179 200 s 2000 5,18 12 96 105 M 10x42 17 3,1 27 90 LTA 186 200/7 18,0 -18,6 KA 186 200 s 12 LTA 193 200/8 18,7 -19,3 KA 193 200 s 12

LTA 203 200/5+9 19,4 -20,3 F 2698 KA 203 200 s 2000 11 4,2 LTA 213 200/6+10 20,4 -21,3 (Fig. 2) KA 213 200 s 2000 6,35 11 115 115 M 10x45 17 4,2 28 90 LTA 222 200/7+11 21,4 -22,2 KA 222 200 s 2000 12 4,4 LTA 231 220/8+12 22,3 -23,1 KA 231 220 s 2200 12 4,4

LTA 237 220/5+9 23,2 -23,7 F 2789 KA 237 220 s 2200 12 LTA 243 220/6+10 23,8 -24,3 (Fig. 2) KA 243 220 s 2200 6,35 13 127 136 M 12x55 19 5,7 27 85 LTA 249 240/7+11 24,4 -24,9 KA 249 240 s 2400 13 LTA 256 240/8+12 25,0 -25,6 KA 256 240 s 2400 13

LTA 265 240/7+13 25,7 -26,5 F 2730 KA 265 240 s 2400 11 8,7 LTA 274 250/8+14 26,6 -27,4 (Fig. 2) KA 274 250 s 2500 11 8,7 LTA 283 250/9+15 27,5 -28,3 KA 283 250 s 2500 7,87 12 140 145 M 12x55 19 9,1 40 150 LTA 292 250/10+16 28,4 -29,2 KA 292 250 s 2500 12 9,1 LTA 299 300/11+17 29,3 -29,9 KA 299 300 s 3000 12 9,1 LTA 306 300/12+18 30,0 -30,6 KA 306 300 s 3000 12 9,1

LTA 311 300/6+11 30,70 -31,14 F 2792 KA 311 300 s 11



Stand: 06. November 2008Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (with shunt attachment)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

12 / 117

LTA 317 300/7+12 31,15 -31,74 (Fig. 2) KA 317 300 s 11 LTA 326 300/8+13 31,75 -32,66 KA 326 300 s 3000 9,27 12 150 200 M 12x55 19 13,0 40 150 LTA 333 300/9+14 32,67 -33,37 KA 333 300 s 12 LTA 344 300/10+15 33,38 -34,43 KA 344 300 s 12




Material: Helical rods: Aluminium alloy Clamp body: Aluminium alloy Straps: Steel, h.d.g. Bolt: Steel, h.d.g. Insert: Neoprene


Remarks:

For installation follow RIBE-Mounting Instruction No. 10. All mentioned armour grip suspensions are available with left-hand lay direction on request (order example: LTA 172 200/5 lis). Armour grip suspensions and shunts have to be ordered separately (shunts: see data-sheet B834/1 and B834/2). For other executions please inquire.

Stand: 06. November 2008Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (with shunt attachment)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

13 / 117

B801/3 Armour grip suspensions for self supporting optical fible aerial cables (without shunt attachment, short version)

1 ..... Clamp body with neoprene-insert 2 ..... Helical rods 3 ..... Fig. 1 4 ..... Fig. 2 5 ..... Bolt 1

LTA 097 130/17 9,0 - 9,7 B 801 006 KA 097 127 1270 8 LTA 104 130/5 9,8 - 10,4 (Fig. 1) KA 104 130 1300 9 LTA 111 130/6 10,5 - 11,1 KA 111 130 1300 10 LTA 118 130/9 11,2 - 11,8 KA 118 130 1300 4,24 10 76 82 M 8x35 13 1,8 16 40 LTA 125 130/10 11,9 -12,5 KA 125 130 1300 10 LTA 131 130/11 12,6 -13,1 KA 131 130 1300 11 LTA 137 130/12 13,2 -13,7 KA 137 130 1300 11

LTA 144 132 13,8 -14,4 F 13 108 KA 144 132 1320 11 2,1 LTA 149 132 14,5 -14,9 (Fig. 1) KA 149 132 1320 11 2,1 LTA 157 132 15,0 -15,7 KA 157 132 1320 4,62 11 89 84 M 8x35 13 2,2 22 90 LTA 161 142 15,8 - 16,1 KA 161 142 1420 12 2,4 LTA 165 142 16,2 - 16,5 KA 165 142 1420 12 2,4

LTA 172 152 16,6 - 17,2 F 2787 KA 172 152 11 LTA 179 152 17,3 - 17,9 (Fig. 2) KA 179 152 1520 5,18 12 96 105 M 10x42 17 3,1 27 90 LTA 186 152 18,0 - 18,6 KA 186 152 12 LTA 193 152 18,7 - 19,3 KA 193 152 12

LTA 203 162 19,4 - 20,3 F 2698 KA 203 162 1620 11 4,2 LTA 213 162 20,4 - 21,3 (Fig. 2) KA 213 162 1620 6,35 11 115 115 M 10x45 17 4,2 28 90 LTA 222 168 21,4 - 22,2 KA 222 168 1680 12 4,4 LTA 231 168 22,3 - 23,1 KA 231 168 1680 12 4,4

LTA 237 193 23,2 - 23,7 F 2789 KA 237 193 12 LTA 243 193 23,8 - 24,3 (Fig. 2) KA 243 193 1930 6,35 13 127 136 M 12x55 19 5,7 27 85 LTA 249 193 24,4 - 24,9 KA 249 193 13 LTA 256 193 25,0 - 25,6 KA 256 193 13

LTA 265 213 25,7 -26,5 F 2730 KA 265 213 11 8,7 LTA 274 213 26,6 -27,4 (Fig. 2) KA 274 213 11 8,7 LTA 283 213 27,5 -28,3 KA 283 213 2130 7,87 12 140 145 M 12x55 19 9,1 40 150 LTA 292 213 28,4 -29,2 KA 292 213 12 9,1 LTA 299 213 29,3 - 29,9 KA 299 213 12 9,1 LTA 306 213 30,0 - 30,6 KA 306 213 12 9,1

LTA 311 224 30,70 -31,14 F 2792 KA 311 224 11 11,2 LTA 317 224 31,15 -31,74 (Fig. 2) KA 317 224 11 11,2



Stand: 25. Juli 2007Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (without shunt attachment, short version)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

14 / 117

LTA 326 224 31,75 -32,66 KA 326 224 2240 9,27 12 150 200 M 12x55 19 11,7 40 150 LTA 333 224 32,67 -33,37 KA 333 224 12 11,7 LTA 344 224 33,38 -34,43 KA 344 224 12 11,7




Material: Helical rods: Alumnium alloy Clamp body: Aluminium alloy Straps: Steel, h.d.g. Bolt: Steel, h.d.g. Insert: Neoprene


Remarks:

For installation follow RIBE-Mounting Instruction No. 10. All mentioned armour grip suspensions are available with left-hand lay direction on request (order example: LTA 118 13/9 li). For other executions please inquire.

Stand: 25. Juli 2007Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (without shunt attachment, short version)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

15 / 117

B801/4 Armour grip suspensions for self supporting optical fible aerial cables (with shunt attachment, short version)

1 ..... Clamp body with neoprene-insert 2 ..... Helical rods 3 ..... Fig. 1 4 ..... Fig. 2 5 ..... Attachment for shunts 6 ..... Bolt 1

LTA 097 130/18 9,0 - 9,7 B 801 006 KA 097 127 8 LTA 104 130/7 9,8 - 10,4 (Fig. 1) KA 104 130 9 LTA 111 130/8 10,5 - 11,1 KA 111 130 10 LTA 118 130/13 11,2 - 11,8 KA 118 130 1800 4,24 10 76 82 M 8x35 13 1,8 16 40 LTA 125 130/14 11,9 - 12,5 KA 125 130 10 LTA 131 130/15 12,6 - 13,1 KA 131 130 11 LTA 137 130/16 13,2 - 13,7 KA 137 130 11

LTA 144 132/6 13,8 - 14,4 F 13 108 KA 144 132 1320 11 2,1 LTA 149 132/7 14,5 - 14,9 (Fig. 1) KA 149 132 1320 11 2,1 LTA 157 132/8 15,0 - 15,7 KA 157 132 1320 4,62 11 89 84 M 8x35 13 2,2 22 90 LTA 161 142/9 15,8 - 16,1 KA 161 142 1420 12 2,4 LTA 165 142/10 16,2 - 16,5 KA 165 142 1420 12 2,4

LTA 172 152/5 16,6 - 17,2 F 2787 KA 172 152 11 LTA 179 152/6 17,3 - 17,9 (Fig. 2) KA 179 152 2000 5,18 12 96 105 M 10x42 17 3,1 27 90 LTA 186 152/7 18,0 - 18,6 KA 186 152 12 LTA 193 152/8 18,7 - 19,3 KA 193 152 12

LTA 203 162/5 19,4 - 20,3 F 2698 KA 203 162 1620 11 4,2 LTA 213 162/6 20,4 - 21,3 (Fig. 2) KA 213 162 1620 6,35 11 115 115 M 10x45 17 4,2 28 90 LTA 222 168/7 21,4 - 22,2 KA 222 168 1680 12 4,4 LTA 231 168/8 22,3 - 23,1 KA 231 168 1680 12 4,4

LTA 237 193/5+9 23,2 - 23,7 F 2789 KA 237 193 1930 12 LTA 243 193/6+10 23,8 - 24,3 (Fig. 2) KA 243 193 1930 6,35 13 127 136 M 12x55 19 5,7 27 85 LTA 249 193/7+11 24,4 - 24,9 KA 249 193 1930 13 LTA 256 193/8+12 25,0 - 25,6 KA 256 193 1930 13

LTA 265 213/7+13 25,7 - 26,5 F 2730 KA 265 213 11 8,7 LTA 274 213/8+14 26,6 - 27,4 (Fig. 2) KA 274 213 11 8,7 LTA 283 213/9+15 27,5 - 28,3 KA 283 213 2130 7,87 12 140 145 M 12x55 19 9,1 40 150 LTA 292 213/10+16 28,4 - 29,2 KA 292 213 12 9,1 LTA 299 213/11+17 29,3 - 29,9 KA 299 213 12 9,1 LTA 306 213/12+18 30,0 - 30,6 KA 306 213 12 9,1

LTA 311 224/6+11 30,70 -31,14 F 2792 KA 311 224 11 11,2



Stand: 25. Juli 2007Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (with shunt attachment, short version)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

16 / 117

LTA 317 224/7+12 31,15 -31,74 (Fig. 2) KA 317 224 11 11,2 LTA 326 224/8+13 31,75 -32,66 KA 326 224 2240 9,27 12 150 200 M 12x55 19 11,7 40 150 LTA 333 224/9+14 32,67 -33,37 KA 333 224 12 11,7 LTA 344 224/10+15 33,38 -34,43 KA 344 224 12 11,7




Material: Helical rods: Alumnium alloy Clamp body: Aluminium alloy Straps: Steel, h.d.g. Bolt: Steel, h.d.g. Insert: Neoprene


Remarks:

Armour grip suspensions and shunts have to be ordered separately (shunts: see data-sheet B834/1 and B834/2). For other executions please inquire.

For installation follow RIBE-Mounting Instruction No. 10. All mentioned armour grip suspensions are available with left-hand lay direction on request (order example: LTA 118 130/16 li).

Stand: 25. Juli 2007Pfad: Optofit/ Suspension fittings/ Armour grip suspensions for self supporting optical fible aerial cables (with shunt attachment, short version)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

17 / 117

B803/1 C-shaped supports for armour grip suspensions

F1 ..... Horizontal tensile force F2 ..... Vertical tensile force F3 ..... Horizontal tensile force rectangular to the line direction

RIBE-Order-No. Minimum Failure Load* Mass/pcs

d1 d

2 F

1 F

2 F

3

mm mm kN kN kN

F 13 818/1 13,5 20

F 13 818/2 15,0 20

F 13 818/3 18,0 20

F 13 818/4 20,5 20

F 13 818/5 13,5 24 40 40 40 11,4

F 13 818/6 15,0 24

F 13 818/7 18,0 24

F 13 818/8 20,5 24

F 13 818/9 24,0 20

* Specified Minimum Failure Loads for bolts and nuts 8.8 h.d.g.

Material: Support: Cast steel, h.d.g. Pivotal joints: Cast steel, h.d.g. Pin: Stainless steel

Application: C-shaped supports are preferably used on the top of suspension towers to suspend ground wires and optical fibre aerial cables. The attachment of the suspension clamp is made by a cardanic joint which assures universal movement of the suspension fitting. The mechanical behaviour of the suspension is almost identical to that of the conductor suspension in suspension sets. The C-shaped support is resistant to short-circuit. Additionally articulation points can be thermically relieved by using shunts. C-shaped supports can also be installed with insulation. For that the insulation set RIBE-No. 115 250 is required. The connection for suspension clamps correponds to LA/ LB 19 or 22 to DIN 48 074, i.e. all customary suspension clamps with strap widths according to GA/ GB 19 or 22 can be inserted without changing of straps.

Stand: 26. Juni 2006Pfad: Optofit/ Suspension fittings/ C-shaped supports for armour grip suspensions/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

18 / 117

Because of its C-shape, the support permits the suspension clamp to pivot up to 45.

Fig.: Mounting example C-shaped support and armour grip suspension

Remarks: Bolts for tower connection of the support are included only upon special request with indication of required bolt dimension. Armour grip suspensions and C-shaped supports have to be ordered separately (armour grip suspensions for C-shaped support: see data-sheet B801 ff.) For other executions please inquire.

Stand: 26. Juni 2006Pfad: Optofit/ Suspension fittings/ C-shaped supports for armour grip suspensions/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

19 / 117

B804/1 Suspension supports without shunt attachment

RIBE-Order-No. Clamping range Helical rods

mm

F 13 820/3 9,8 - 10,4 KA 104 180s

F 13 820/5 10,5 - 11,1 KA 111 180s

F 13 820/1 11,2 - 11,8 KA 118 180s

F 13 820/7 11,9 - 12,5 KA 125 180s

F 13 820/9 12,6 - 13,1 KA 131 180s

F 13 820/11 13,2 - 13,7 KA 137 180s

B 804 014/1 13,8 - 14,4 KA 144 180s

B 804 014/2 14,5 - 14,9 KA 149 180s

B 804 014/3 15,0 - 15,7 KA 157 180s

B 804 014/4 15,8 - 16,1 KA 161 200s

B 804 014/5 16,2 - 16,5 KA 165 200s

Material: Support: Steel, h.d.g. Helical rods: Aluminium alloy

Application:

Suspension supports are preferably installed on the top of suspension towers and are used for the suspension of ground wires and optical fibre aerial cables. The suspension support is resistant to short-circuit. Additionally articulation points can be thermically relieved by shunts. Suspension supports can also be installed with insulation. For that the insulation set RIBE-No. 115 250 is required.

Remark: Bolts for tower connection of the support are included only upon request with indication of required bolt dimension.

Stand: 16. Mai 2006Pfad: Optofit/ Suspension fittings/ Suspension supports without shunt attachment/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

20 / 117

B804/2 Suspension supports with shunt attachment

RIBE-Order-No. Clamping range Helical rods Shunt

mm

F 13 820/4 9,8 - 10,4 KA 104 180s F 13 820-04 (Cu 35 mm)

F 13 820/6 10,5 - 11,1 KA 111 180s F 13 820-04 (Cu 35 mm)

F 13 820/2 11,2 - 11,8 KA 118 180s F 13 820-04 (Cu 35 mm)

F 13 820/8 11,9 - 12,5 KA 125 180s F 13 820-04 (Cu 35 mm)

F 13 820/10 12,6 - 13,1 KA 131 180s F 13 820-04 (Cu 35 mm)

F 13 820/12 13,2 - 13,7 KA 137 180s F 13 820-04 (Cu 35 mm)

B 804 014/6 13,8 - 14,4 KA 144 180s F 13 815-03 (Cu 35 mm)

B 804 014/7 14,5 - 14,9 KA 149 180s F 13 815-03 (Cu 35 mm)

B 804 014/8 15,0 - 15,7 KA 157 180s F 13 815-03 (Cu 35 mm)

B 804 014/9 15,8 - 16,1 KA 161 200s F 13 815-03 (Cu 35 mm)

B 804 014/10 16,2 - 16,5 KA 165 200s F 13 815-03 (Cu 35 mm)

Material: Support: Steel, h.d.g. Helical rods: Aluminium alloy Shunt: Copper

Application:

Suspension supports are preferably installed on the top of suspension towers and are used for the suspension of ground wires and optical fibre aerial cables. The suspension support is resistant to short-circuit. Additionally articulation points can be thermically relieved by shunts. Suspension supports can also be installed with insulation. For that the insulation set RIBE-No. 115 250 is required.

Remarks: Bolts for tower connection of the support are included only upon request with indication of required bolt dimension. Suspension supports and shunts have to be ordered separately.

Stand: 16. Mai 2006Pfad: Optofit/ Suspension fittings/ Suspension supports with shunt attachment/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

21 / 117

B804/4 Suspension supports without shunt attachment (special design)

1 ..... Bolts

RIBE-Order-No. Clamping range Helical rods Bolts

mm

B 804 018/14 9,0 - 9,7 KA 097 180 lis M16

B 804 018/7 9,8 - 10,4 KA 104 180 lis M16

B 804 018/8 10,5 - 11,1 KA 111 180 lis M16

B 804 018/9 11,2 - 11,8 KA 118 180 lis M16

B 804 018/10 11,9 - 12,5 KA 125 180 lis M16

B 804 018/11 12,6 - 13,1 KA 131 180 lis M16

B 804 018/12 13,2 - 13,7 KA 137 180 lis M16

B 804 017/6 13,8 - 14,4 KA 144 180 lis M16

B 804 017/7 14,5 - 14,9 KA 149 180 lis M16

B 804 017/8 15,0 - 15,7 KA 157 180 lis M16

B 804 017/9 15,8 - 16,1 KA 161 200 lis M16

B 804 017/10 16,2 - 16,5 KA 165 200 lis M16

B 804 019/5 16,6 17,2 KA 172 200 lis M16

B 804 019/6 17,3 17,9 KA 179 200 lis M16

B 804 019/7 18,0 18,6 KA 186 200 lis M16

B 804 019/8 18,7 19,3 KA 193 200 lis M16

Material: Support: Steel, h.d.g. Helical rods: Alumimium alloy

Application:

Remark: Bolts for tower connection of the support are included only upon request with indication of required bolt dimension.

Suspension supports are preferably installed on the top of suspension towers and are used for the suspension of ground wires and optical fibre aerial cables. The suspension support is resistant to short-circuit. Additionally articulation points can be thermically relieved by shunts.

Stand: 03. Mai 2007Pfad: Optofit/ Suspension fittings/ Suspension supports without shunt attachment (special design)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

22 / 117

B804/5 Suspension supports with shunt attachment (special design)

1 ..... Bolts

RIBE-Order-No. Clamping range Helical rods Bolts Shunt

mm

B 804 018/13 9,0 - 9,7 KA 097 180 lis M16 60 500

B 804 018/1 9,8 - 10,4 KA 104 180 lis M16 60 500

B 804 018/2 10,5 - 11,1 KA 111 180 lis M16 60 500

B 804 018/3 11,2 - 11,8 KA 118 180 lis M16 60 500

B 804 018/4 11,9 - 12,5 KA 125 180 lis M16 60 500

B 804 018/5 12,6 - 13,1 KA 131 180 lis M16 60 500

B 804 018/6 13,2 - 13,7 KA 137 180 lis M16 60 500

B 804 017/1 13,8 - 14,4 KA 144 180 lis M16 60 501

B 804 017/2 14,5 - 14,9 KA 149 180 lis M16 60 501

B 804 017/3 15,0 - 15,7 KA 157 180 lis M16 60 501

B 804 017/4 15,8 - 16,1 KA 161 200 lis M16 60 501

B 804 017/5 16,2 - 16,5 KA 165 200 lis M16 60 501

B 804 019/1 16,6 17,2 KA 172 200 lis M16 60 502

B 804 019/2 17,3 17,9 KA 179 200 lis M16 60 502

B 804 019/3 18,0 18,6 KA 186 200 lis M16 60 502

B 804 019/4 18,7 19,3 KA 193 200 lis M16 60 502

Material: Support: Steel, h.d.g. Helical rods: Aluminium rods Shunt: Copper

Application:

Remarks: Bolts for tower connection of the support are included only upon request with indication of required bolt dimension. Suspension supports and shunts have to be ordered separately. Shunts: see data-sheet B834/1 and B834/2

Suspension supports are preferably installed on the top of suspension towers and are used for the suspension of ground wires and optical fibre aerial cables. The suspension support is resistant to short-circuit. Additionally articulation points can be thermically relieved by shunts.

Stand: 03. Mai 2007Pfad: Optofit/ Suspension fittings/ Suspension supports with shunt attachment (special design)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

23 / 117

B805/2 Suspension rods for ADSS cable and medium span lengths from 70 - 150 m

1 ..... Suspension rods 2 ..... Thimble 3 ..... Protection rods

RIBE-Order-No. Clamping range Dia. of rods L No. of rods Thimble Mass/ pcsmm mm mm kg

TG 127 096 12,00 - 12,72 3,02 960 3 E 5119 0,21TG 134 097 12,73 -13,49 3,02 970 3 E 5119 0,22TG 143 098 13,50 - 14,31 3,02 980 3 E 5119 0,22TG 151 099 14,32 - 15,18 3,02 990 3 E 5119 0,23TG 161 098 15,19 - 16,11 3,02 990 3 E 5119 0,23TG 170 099 16,12 - 17,08 3,02 1000 3 E 5119 0,24

TG 181 123 17,09 - 18,12 3,51 1240 4 F 12006 0,50TG 192 125 18,13 - 19,22 3,51 1250 4 F 12006 0,51TG 203 125 19,23 - 20,38 3,51 1260 4 F 12006 0,51TG 216 127 20,39 - 21,61 3,51 1270 4 F 12006 0,52TG 229 128 21,62 - 22,92 3,51 1280 4 F 12006 0,53TG 243 170 22,93 - 24,31 3,51 1700 4 F 12006 0,65TG 257 173 24,32 - 25,77 4,04 1730 4 F 12006 0,88TG 273 175 25,78 - 27,33 4,04 1750 4 F 12006 0,90TG 289 259 27,34 - 28,98 4,04 2600 4 F 12006 1,21TG 307 262 28,99 - 30,73 4,04 2620 4 F 12006 1,23

Material: Helical rods: Steel, h.d.g.

Application:

Suspension rods consisting of TG-suspension and UTA-protection rods are designed for vertical loads up to 5 kN. They are used for span lengths from 70 - 150 m approximately. The loop of the TG-suspension rods is stabilized and protected against abrasion by a ring type thimble.

Fig.: Mounting example

1 ..... Protection rods

Stand: 10. August 2006Pfad: Optofit/ Suspension fittings/Suspension rods for ADSS cable and medium span lengths from 70 - 150 m/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

24 / 117

2 ..... Hook 3 ..... Suspension rods

Remarks:

Ring type thimbles (see data-sheet B823), UTA-protection rods (see data-sheet B814/2) and TG-suspension rods have to be ordered separately. When selecting the suspension rods it must be considered that the total diameter results from the cable diameter plus two times the rod diameter of protection rods. Installation instructions see data-sheet Mon69.

Stand: 10. August 2006Pfad: Optofit/ Suspension fittings/Suspension rods for ADSS cable and medium span lengths from 70 - 150 m/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

25 / 117

B805/3 Pulley clamps with spiral attachment for ADSS cable, span lengths up to 150 m and tensile forces up to 2,5 kN

1 ..... Helical rods 2 ..... Suspension pulley

RIBE-Order-No. Clamping range Helical rods Dia. of rods L No. of rods Mass/ pcsmm mm mm kg

F 13 255-20/01 7,65 - 8,45 HRG 084 067 2,54 670 8 1,19F 13 255-20/02 8,46 - 9,26 HRG 092 090 2,54 900 8 1,26F 13 255-20/03 9,27 - 10,27 HRG 102 068 2,54 680 8 1,24F 13 255-20/04 10,28 - 11,30 HRG 113 070 2,54 700 10 1,26F 13 255-20/05 11,31 - 12,35 HRG 123 102 3,02 1020 10 1,56F 13 255-20/06 12,36 - 13,41 HRG 134 094 3,02 940 10 1,53F 13 255-20/07 13,42 - 14,49 HRG 144 103 3,02 1030 10 1,58F 13 255-20/08 14,50 - 15,60 HRG 156 105 3,51 1050 10 1,82F 13 255-20/09 15,61 - 16,71 HRG 167 114 3,51 1140 10 1,89F 13 255-20/10 16,72 - 17,82 HRG 178 118 3,51 1180 10 1,93F 13 255-20/11 17,83 - 18,90 HRG 189 122 3,51 1220 10 1,97F 13 255-20/12 18,94 - 20,24 HRG 202 124 3,51 1240 10 2,01F 13 255-20/13 20,25 - 21,55 HRG 215 125 3,51 1250 10 2,05F 13 255-20/14 21,56 - 22,86 HRG 228 127 3,51 1270 10 2,09


Application: Pulley clamps with spiral attachment are designed for span lengths up to 150 m approximately and tensile forces up to 2,5 kN.

Stand: 18. August 2006Pfad: Optofit/ Suspension fittings/ Pulley clamps with spiral attachment for ADSS cable, span lengths up to 150 m and tensile forces up to 2,5 kN/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

26 / 117

B805/5 Suspension rods for ADSS cable and short span lengths up to 70 m

1 ..... Suspension rods 2 ..... Thimble 3 ..... Supporting rods

RIBE-Order-No. Clamping range Dia. of rods LTG LLG No. of rods Thimble Mass/ pcs

TG LG TG LG mm mm mm mm kg kg

TG 075 091 LG 075 046 s 6,91 - 7,5 2,18 910 460 3 4 E 5119 0,10 0,06TG 082 092 LG 082 046 s 7,51 - 8,2 2,54 920 460 3 4 E 5119 0,14 0,08TG 088 093 LG 088 047 s 8,21 - 8,8 2,54 930 470 3 4 E 5119 0,14 0,08TG 095 095 LG 095 047 s 8,81 - 9,5 2,54 950 470 3 4 E 5119 0,14 0,08TG 102 096 LG 102 048 s 9,51 - 10,2 2,54 960 480 3 4 E 5119 0,14 0,08TG 108 096 LG 108 048 s 10,21 - 10,8 3,02 960 480 3 4 E 5119 0,21 0,11TG 114 097 LG 114 049 s 10,81 - 11,4 3,02 970 490 3 4 E 5119 0,21 0,12TG 120 098 LG 120 049 s 11,41 - 12,0 3,02 980 490 3 4 E 5119 0,21 0,12TG 126 100 LG 126 050 s 12,01 - 12,6 3,02 1000 500 3 4 E 5119 0,22 0,12TG 132 100 LG 132 050 s 12,61 - 13,2 3,02 1000 500 3 4 E 5119 0,22 0,12TG 138 101 LG 138 051 s 13,21 - 13,8 3,02 1010 510 3 4 E 5119 0,22 0,12TG 144 101 LG 144 051 s 13,81 - 14,4 3,02 1010 510 3 4 E 5119 0,22 0,13TG 150 101 LG 150 051 s 14,41 - 15,0 3,02 1010 510 3 4 E 5119 0,22 0,13TG 156 103 LG 156 052 s 15,01 - 15,6 3,02 1030 520 3 4 E 5119 0,23 0,13TG 162 103 LG 162 052 s 15,61 - 16,2 3,02 1030 520 3 4 E 5119 0,23 0,13TG 168 122 LG 168 073 s 16,21 - 16,8 3,02 1220 730 4 4 F 12006 0,36 0,18TG 174 122 LG 174 073 s 16,81 - 17,4 3,02 1220 730 3 4 F 12006 0,36 0,18TG 180 123 LG 180 074 s 17,41 - 18,0 3,02 1230 740 3 4 F 12006 0,36 0,18TG 186 123 LG 186 074 s 18,01 - 18,6 3,02 1230 740 3 4 F 12006 0,37 0,18TG 192 124 LG 192 075 s 18,61 - 19,2 3,02 1240 750 3 4 F 12006 0,37 0,19TG 198 124 LG 198 075 s 19,21 - 19,8 3,02 1240 750 4 4 F 12006 0,37 0,19TG 204 125 LG 204 075 s 19,81 - 20,4 3,02 1250 750 4 4 F 12006 0,38 0,19TG 210 125 LG 210 076 s 20,41 - 21,0 3,02 1250 760 3 4 F 12006 0,38 0,19TG 216 126 LG 216 076 s 21,01 - 21,6 3,02 1260 760 4 4 F 12006 0,39 0,19TG 222 127 LG 222 076 s 21,61 - 22,2 3,02 1270 760 4 4 F 12006 0,39 0,19


Application:

Suspension rods consisting of thimble, LG- and TG-helical rods are designed for vertical loads up to 1kN. They are used for span lengths up to 70 m approximately. The TG-suspension rods with the preformed loop is the supporting accessory. The shorter and straight LG-supporting rods are only used for stiffening the area round the suspension point. The loop of the fitting is stabilized and protected against abrasion with a ring type thimble.

Stand: 18. August 2006Pfad: Optofit/ Suspension fittings/ Suspension rods for ADSS cable and short span lengths up to 70 m/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

27 / 117

Fig.: Mountimg example

1 ..... Suspension rods 2 ..... Hook

Remarks: Ring type thimbles see data-sheet B823. TG-suspension rods and LG-supporting rods have to be ordered separately. Mounting instruction see data-sheet Mon51.

Stand: 18. August 2006Pfad: Optofit/ Suspension fittings/ Suspension rods for ADSS cable and short span lengths up to 70 m/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

28 / 117

B806/1 Suspension pulleys for ADSS

1 ..... ADSS cable

RIBE-Order-No. Diameter of ADSS cable

a mm

Rated force

FN

kN

Mass / pcs

kg

F 13 256 = 12 60 130 5 0,40

F 13 255/1 = 20 154 180 5 0,97

F 13 255/2 = 30 154 180 5 0,97

b mm

c mm

Material: Roll: Polyamid Straps: Steel, h.d.g. Bolt, nut: h.d.g., alternatively stainless steel

Application:

Suspension pulleys are used for suspension of ADSS cables (preferably at wooden pole or concrete pole - see figure below). The suspension pulleys benefit from the fact that in case of a tree falling in the span length the ADSS cable is not destroyed. This has no influence on the communication line. To avoid high compression forces at the point of contact between cable and suspension pulleys the use of protection rods is recommended.


1 ..... Wooden pole 2 ..... Thimble 3 ..... Hook

Stand: 18. August 2006Pfad: Optofit/ Suspension fittings/ Suspension pulleys for ADSS/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

29 / 117

4 ..... Helical dead end 5 ..... Suspension pulley 6 ..... Protection rods 7 ..... ADSS

Remark: For other executions please inquire.

Stand: 18. August 2006Pfad: Optofit/ Suspension fittings/ Suspension pulleys for ADSS/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

30 / 117

B810/0 Introduction to helical dead ends

1 ..... Helical dead end 2 ..... Thimble 3 ..... Black crossing mark

Design and performance: Helical dead ends are ideally suited for the full tensioning of self supporting optical fibre aerial cables.

Material:

Installation: The legs of the dead end are wrapped on the cable starting at the marked crossing point. Special tooling is not required. For installation follow RIBE-Mounting Instruction No. 9.

Dead ends are composed of five or more preassembled helical rods which are covered with a small-grained sand on the inside to improve the frictional contact. The loop of the dead end is protected from abrasion by means of a thimble. The deformation of the cable is omitted as the radial compression is distributed over a large contact area.

The helical rods are made of a high-tensile, corrosion-resistant aluminium alloy, of high-tensile hot-dip galvanized steel, or Aluminium-clad steel; thimbles of hot-dip galvanized malleable cast iron and cotter pins or threaded bolts of hot-dip galvanized steel with tensile strength class 8.8.

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ Introduction to helical dead ends/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

31 / 117

B811 AW-Helical dead ends for OPGW, ADSS and ACSR


AW 058 052 5,56 - 5,84 2,59 520 570 4 0,16

AW 061 053 5,85 - 6,11 2,59 530 580 4 0,16

AW 063 054 6,12 - 6,36 2,59 540 590 4 0,17

AW 068 076 s 6,61 - 6,84 2,59 760 810 4 F 2684/3 0,24

AW 071 055 6,85 - 7,12 2,59 550 600 4 0,17

AW 076 058 7,13 - 7,68 2,59 580 630 5 0,23

AW 079 060 7,69 - 7,95 2,59 600 650 5 0,24

AW 082 064 7,91 - 8,23 2,59 640 690 5 0,25

AW 090 074 8,71 - 9,02 2,90 740 790 5 0,36

AW 099 080 9,47 - 9,95 3,25 800 850 4 0,40

AW 100 080 9,65 - 10,00 3,25 800 850 5 0,50

AW 104 083 10,01 - 10,45 3,25 830 880 5 0,51

AW 108 086 10,46 - 10,84 3,25 860 910 6 F 2684/3 0,64

AW 112 090 10,85 - 11,23 3,25 900 950 5 or 0,70

AW 117 119 s 11,24 - 11,70 3,25 1190 1240 6 F 2685/3 0,88

AW 121 096 11,50 - 12,10 3,25 960 1010 6 0,70

AW 128 099 12,11 - 12,80 3,25 990 1050 6 0,71

AW 133 100 12,81 - 13,39 3,25 1000 1050 6 0,75

AW 140 102 13,40 - 14,40 3,25 1020 1070 6 0,75

AW 165 102 14,50 - 16,50 3,25 1020 1070 6 0,74

AW 165 117 s 14,50 - 16,50 4,65 1170 1220 5 1,50

AW 172 106 15,20 - 17,20 3,25 1068 1110 6 0,76

AW 177 125 s 16,51 - 17,79 4,65 1260 1310 6 1,92

AW 193 111 17,30 - 19,30 3,25 1110 1160 8 F 2685/3 1,08

AW 193 113 17,30 - 19,30 4,65 1136 1186 6 1,73

AW 188 136 s 17,60 - 18,80 4,65 1340 1390 6 2,04

AW 214 144 19,40 - 21,40 4,65 1440 1490 6 2,10

AW 225 152 20,50 - 22,50 4,65 1520 1570 6 2,22

AW 237 152 21,70 - 23,70 4,65 1496 1570 7 2,66

AW 252 152 23,20 - 25,20 4,65 1520 1580 7 2,58

AW 270 176 25,00 - 27,00 4,65 1760 1820 8 F 2686/2 3,40

AW 285 176 26,50 - 28,50 4,65 1760 1820 8 3,50

RIBE-Order-No. Clamping range Dia. of rods L1 L2 No. of Thimble Mass/ piece

mm mm mm mm rods RIBE-No. kg

Stand: 25. Juli 2007Pfad: Optofit/ Fittings for tension towers/ AW-Helical dead ends for OPGW, ADSS and ACSR/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

32 / 117

AW 306 192 28,50 - 30,60 4,65 1920 1990 8 3,70

AW 326 199 30,60 - 32,60 4,65 1990 2060 9 4,35

AW 341 200 32,10 - 34,10 4,65 2000 2070 10 5,05

AW 350 200 33,00 - 35,00 5,18 2000 2070 9 5,60

AW 370 224 35,00 - 37,00 5,18 2240 2300 9 6,18

AW 390 232 37,00 - 39,00 5,18 2320 2400 10 6,90

RIBE-Order-No. Clamping range Dia. of rods L1 L2 No. of Thimble Mass/ piece

mm mm mm mm rods RIBE-No. kg

Material: Helical rods: Aluminium-clad steel Thimble: Malleable cast iron, h.d.g.


Remarks:

For installation follow RIBE-Mounting Instruction No. 9.

Order example: AW 128 099 li Thimbles: see data-sheet B821

When selecting helical dead ends the total diameter resulting from the cable diameter plus two times the rod diameter of the protection rods has to be taken into account. Furthermore the rated forces of thimbles are observed (see data-sheet B821). These dead end designs are only suitable for cables or conductors with right-hand lay armoring and ADSS cables. If dead ends for left-hand lay cables or conductors are required this must specifically be stated when placing the order.

Stand: 25. Juli 2007Pfad: Optofit/ Fittings for tension towers/ AW-Helical dead ends for OPGW, ADSS and ACSR/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

33 / 117

B812 RW-Protection rods

RW 090 140 lis 8,0 - 9,0 2,59 1400 11 4 - 4 - 3 x 0,60

RW 090 160 lis 8,0 - 9,0 2,59 1600 11 4 - 4 - 3 x 0,68

RW 090 240 lis 8,0 - 9,0 2,59 2400 11 4 - 4 - 3 x 1,01

RW 101 140 lis 9,1 - 10,1 2,59 1400 12 4 - 4 - 4 x 0,65

RW 101 160 lis 9,1 - 10,1 2,59 1600 12 4 - 4 - 4 x 0,74

RW 101 180 lis 9,1 - 10,1 2,59 1800 12 4 - 4 - 4 x 0,83

RW 101 190 lis 9,1 - 10,1 2,59 1900 12 4 - 4 - 4 x 0,68

RW 101 240 lis 9,1 - 10,1 2,59 2400 12 4 - 4 - 4 x 1,11

RW 112 150 lis 10,2 - 11,2 2,59 1500 13 4 - 3 - 3 - 3 x 0,76

RW 112 160 lis 10,2 - 11,2 2,59 1600 13 4 - 3 - 3 - 3 x 0,80

RW 112 200 lis 10,2 - 11,2 2,59 2000 13 4 - 3 - 3 - 3 x 1,00

RW 112 220 lis 10,2 - 11,2 2,59 2200 13 4 - 3 - 3 - 3 x 1,10

RW 112 240 lis 10,2 - 11,2 2,59 2400 13 4 - 3 - 3 - 3 x 1,20

RW 117 180 lis 11,3 - 11,75 3,25 1800 12 3 - 3 - 3 - 3 x 1,34

RW 117 210 lis 11,5 - 11,75 3,25 2100 12 4 - 4 - 4 x 1,50

RW 117 240 lis 11,5 - 11,75 3,25 2400 12 4 - 4 - 4 x 1,71

RW 117 300 lis 11,5 - 11,75 3,25 3000 12 4 - 4 - 4 x 2,23

RW 123 100 lis 11,3 - 12,3 2,90 1000 13 4 - 3 - 3 - 3 0,64

RW 123 140 lis 11,3 - 12,3 2,90 1400 13 4 - 3 - 3 - 3 x 0,89

RW 123 170 lis 11,3 - 12,3 2,90 1700 13 4 - 3 - 3 - 3 x 1,08

RW 123 180 lis 11,3 - 12,3 2,90 1800 13 4 - 3 - 3 - 3 x 1,11

RW 123 210 lis 11,3 - 12,3 2,90 2100 13 4 - 3 - 3 - 3 x 1,30

RW 123 240 lis 11,3 - 12,3 2,90 2400 13 4 - 3 - 3 - 3 x 1,50

RW 123 300 lis 11,3 - 12,3 2,90 3000 13 4 - 3 - 3 - 3 x 1,91

RW 123 380 lis 11,3 - 12,3 2,90 3800 13 4 - 3 - 3 - 3 x 2,42

RW 134 070 lis 12,4 - 13,4 2,90 700 14 4 - 4 - 3 - 3 0,48

RW 134 110 lis 12,4 - 13,4 2,90 1100 14 4 - 4 - 3 - 3 x 0,76

RW 134 140 lis 12,4 - 13,4 2,90 1400 14 4 - 4 - 3 - 3 x 0,96

RW 134 160 lis 12,4 - 13,4 2,90 1600 14 4 - 4 - 3 - 3 x 1,08

RW 134 180 lis 12,4 - 13,4 2,90 1800 14 4 - 4 - 3 - 3 x 1,24

RW 134 210 lis 12,4 - 13,4 2,90 2100 14 4 - 4 - 3 - 3 x 1,42

RW 134 240 lis 12,4 - 13,4 2,90 2400 14 4 - 4 - 3 - 3 x 1,62

RW 134 300 lis 12,4 - 13,4 2,90 3000 14 4 - 4 - 3 - 3 x 2,03

RW 144 070 lis 13,5 - 14,4 3,25 700 14 4 - 4 - 3 - 3 0,70

RW 144 100 lis 13,5 - 14,4 3,25 1000 14 4 - 4 - 3 - 3 0,86

RW 144 120 lis 13,5 - 14,4 3,25 1200 14 4 - 4 - 3 - 3 1,04

RW 144 180 lis 13,5 - 14,4 3,25 1800 14 4 - 4 - 3 - 3 x 1,56

RW 144 200 lis 13,5 - 14,4 3,25 2000 14 4 - 4 - 3 - 3 x 1,73

RW 144 260 lis 13,5 - 14,4 3,25 2600 14 4 - 4 - 3 - 3 x 2,20

RW 144 290 lis 13,5 - 14,4 3,25 2900 14 4 - 4 - 3 - 3 x 2,51

RW 144 320 lis 13,5 - 14,4 3,25 3200 14 4 - 4 - 3 - 3 x 2,77

RW 144 490 lis 13,5 - 14,4 3,25 4900 14 4 - 4 - 3 - 3 x 4,23

RW 144 640 lis 13,5 - 14,4 3,25 6400 14 4 - 4 - 3 - 3 5,54

RW 148 070 lis 13,8 - 14,8 3,25 700 14 4 - 4 - 3 - 3 0,60

RW 148 200 lis 13,8 - 14,8 3,25 2000 14 4 - 4 - 3 - 3 x 1,72

RW 148 260 lis 13,8 - 14,8 3,25 2600 14 4 - 4 - 3 - 3 x 2,25

RW 148 300 lis 13,8 - 14,8 3,25 3000 14 4 - 4 - 3 - 3 x 2,58

RIBE-Order-No. Clamping range Dia. of rods L No. of rods Rod subsets Sanding Mass/ pcs mm mm mm kg

Stand: 18. Dezember 2009Pfad: Optofit/ Fittings for tension towers/ RW-Protection rods/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

34 / 117

RW 165 070 lis 14,5 - 16,5 3,25 700 15 4 - 4 - 4 - 3 0,65

RW 165 100 lis 14,5 - 16,5 3,25 1000 15 4 - 4 - 4 - 3 0,93

RW 165 120 lis 14,5 - 16,5 3,25 1200 15 4 - 4 - 4 - 3 1,11

RW 165 200 lis 14,5 - 16,5 3,25 2000 15 4 - 4 - 4 - 3 x 1,85

RW 165 260 lis 14,5 - 16,5 3,25 2600 15 4 - 4 - 4 - 3 x 2,55

RW 165 300 lis 14,5 - 16,5 3,25 3000 15 4 - 4 - 4 - 3 x 2,95

RW 165 420 lis 14,5 - 16,5 3,25 4200 15 4 - 4 - 4 - 3 x 3,89

RW 165 500 lis 14,5 - 16,5 3,25 5000 15 4 - 4 - 4 - 3 x 4,64

RW 166 200 lis 16,0 - 16,9 3,25 2000 16 4 - 4 - 4 - 4 x 1,98

RW 166 280 lis 16,0 - 16,9 3,25 2800 16 4 - 4 - 4 - 4 x 2,78

RW 176 120 lis 17,0 - 17,6 3,25 1200 17 4 - 4 - 4 - 5 1,27

RW 176 200 lis 17,0 - 17,6 3,25 2000 17 4 - 4 - 4 - 5 x 2,10

RW 176 260 lis 17,0 - 17,6 3,25 2600 17 4 - 4 - 4 - 5 x 2,73

RW 176 280 lis 17,0 - 17,6 3,25 2800 17 4 - 4 - 4 - 5 x 2,94

RW 176 300 lis 17,0 - 17,6 3,25 3000 17 4 - 4 - 4 - 5 x 3,15

RW 193 070 lis 17,3 - 19,3 3,25 700 17 5 - 4 - 4 - 4 0,74

RW 193 100 lis 17,3 - 19,3 3,25 1000 17 5 - 4 - 4 - 4 1,05

RW 193 110 lis 17,3 - 19,3 3,25 1100 17 5 - 4 - 4 - 4 1,15

RW 193 120 lis 17,3 - 19,3 3,25 1200 17 5 - 4 - 4 - 4 1,26

RW 193 150 lis 17,3 - 19,3 3,25 1500 17 5 - 4 - 4 - 4 x 1,57

RW 193 200 lis 17,3 - 19,3 3,25 2000 17 5 - 4 - 4 - 4 x 2,10

RW 193 210 lis 17,3 - 19,3 3,25 2100 17 5 - 4 - 4 - 4 x 2,20

RW 193 220 lis 17,3 - 19,3 3,25 2200 17 5 - 4 - 4 - 4 2,30

RW 193 260 lis 17,3 - 19,3 3,25 2600 17 5 - 4 - 4 - 4 x 2,80

RW 193 290 lis 17,3 - 19,3 3,25 2900 17 5 - 4 - 4 - 4 x 3,04

RW 193 300 lis 17,3 - 19,3 3,25 3000 17 5 - 4 - 4 - 4 x 3,27

RW 193 380 lis 17,3 - 19,3 3,25 3800 17 5 - 4 - 4 - 4 x 4,22

RW 193 440 lis 17,3 - 19,3 3,25 4400 17 5 - 4 - 4 - 4 4,62

RW 193 460 lis 17,3 - 19,3 3,25 4600 17 5 - 4 - 4 - 4 4,83

RW 193 550 lis 17,3 - 19,3 3,25 5500 17 5 - 4 - 4 - 4 5,77

RW 214 070 lis 19,4 - 21,4 4,65 700 14 3 - 3 - 4 - 4 1,28

RW 214 110 lis 19,4 - 21,4 4,65 1100 14 3 - 3 - 4 - 4 1,92

RW 214 240 lis 19,4 - 21,4 4,65 2400 14 3 - 3 - 4 - 4 x 4,40

RW 214 300 lis 19,4 - 21,4 4,65 3000 14 3 - 3 - 4 - 4 x 5,50

RW 214 330 lis 19,4 - 21,4 4,65 3300 14 3 - 3 - 4 - 4 x 6,16

RW 214 500 lis 19,4 - 21,4 4,65 5000 14 3 - 3 - 4 - 4 8,71

Rw 225 070 lis 20,5 - 22,5 4,65 700 15 3 - 4 - 4 - 4 1,31

RW 225 120 lis 20,5 - 22,5 4,65 1200 15 3 - 4 - 4 - 4 2,24

RW 225 150 lis 20,5 - 22,5 4,65 1500 15 3 - 4 - 4 - 4 x 2,80

RW 225 250 lis 20,5 - 22,5 4,65 2500 15 3 - 4 - 4 - 4 x 4,67

RW 225 310 lis 20,5 - 22,5 4,65 3100 15 3 - 4 - 4 - 4 x 5,79

RW 225 350 lis 20,5 - 22,5 4,65 3500 15 3 - 4 - 4 - 4 x 6,54

Rw 225 510 lis 20,5 - 22,5 4,65 5100 15 3 - 4 - 4 - 4 x 9,51

RW 237 070 lis 21,7 - 23,7 4,65 700 16 4 - 4 - 4 - 4 1,40

RW 237 100 lis 21,7 - 23,7 4,65 1000 16 4 - 4 - 4 - 4 2,00

RW 237 120 lis 21,7 - 23,7 4,65 1200 16 4 - 4 - 4 - 4 2,40

RW 237 195 lis 21,7 - 23,7 4,65 1950 16 4 - 4 - 4 - 4 x 3,90

RW 237 250 lis 21,7 - 23,7 4,65 2500 15 4 - 4 - 4 - 3 x 4,68

RW 237 300 lis 21,7 - 23,7 3,25 3000 22 5 - 5 - 5 - 4 - 3 x 4,00

RW 237 310 lis 21,7 - 23,7 4,65 3100 16 4 - 4 - 4 - 4 x 6,20

RW 237 330 lis 21,7 - 23,7 4,65 3300 16 4 - 4 - 4 - 4 x 6,60

RW 237 350 lis 21,7 - 23,7 4,65 3500 16 4 - 4 - 4 - 4 x 7,00

RW 237 500 lis 21,7 - 23,7 4,65 5000 15 4 - 4 - 4 - 3 x 9,40

RW 252 070 lis 23,8 - 25,2 4,65 700 17 4 - 4 - 4 - 5 x 1,47

RW 252 100 lis 23,8 - 25,2 4,65 1000 17 4 - 4 - 4 - 5 x 2,10

RW 252 120 lis 23,8 - 25,2 4,65 1200 17 4 - 4 - 4 - 5 2,55

RW 252 250 lis 23,8 - 25,2 4,65 2500 17 4 - 4 - 4 - 5 x 5,31

RW 252 310 lis 23,8 - 25,2 4,65 3100 17 4 - 4 - 4 - 5 x 6,50



ONLINE-CATALOGUE

35 / 117

RW 252 350 lis 23,8 - 25,2 4,65 3500 17 4 - 4 - 4 - 5 x 7,30

RW 252 510 lis 23,8 - 25,2 4,65 5100 17 4 - 4 - 4 - 5 x 10,30

RW 270 070 lis 25,0 - 27,0 4,65 700 18 5 - 5 - 4 - 4 1,53

RW 270 120 lis 25,0 - 27,0 4,65 1200 18 5 - 5 - 4 - 4 2,63

RW 270 310 lis 25,0 - 27,0 4,65 3100 18 5 - 5 - 4 - 4 x 6,80

RW 270 350 lis 25,0 - 27,0 4,65 3500 18 5 - 5 - 4 - 4 x 7,65

RW 285 400 lis 26,5 - 28,5 4,65 4000 19 4 - 4 - 4 - 4 - 3 x 9,40

RW 306 070 lis 28,5 - 30,6 4,65 700 20 4 - 4 - 4 - 4 - 4 1,73

RW 306 120 lis 28,5 - 30,6 4,65 1200 20 4 - 4 - 4 - 4 - 4 2,96

RW 306 330 lis 28,5 - 30,6 4,65 3300 20 4 - 4 - 4 - 4 - 4 x 8,16

RW 306 380 lis 28,5 - 30,6 4,65 3800 20 4 - 4 - 4 - 4 - 4 x 9,40

RW 306 400 lis 28,6 - 30,6 4,65 4000 20 4 - 4 - 4 - 4 - 4 x 9,80

RW 326 350 lis 30,6 - 32,6 4,65 3500 21 4 - 4 - 4 - 4 - 5 x 9,22


Material: Helical rods: Aluminium-clad steel

Application:

Installation:

Protection rods are preferably made of Aluminium-clad steel-wires and shall protect the self supporting fibre optical aerial cables at tension sets. They are mounted beneath the helical dead end and spread the radial forces on the cable uniformly along the zone of contact. Especially on the cable at the loop-side of the helical dead end radial forces (depending on the tension force) can stress the optical part of the cable inadmissibly. This will cause high damping which results in a reduced data transmission or in the worst case an interruption. The length of the cable guard is determined in such a way that two vibration dampers can be mounted on the rods at the span-side avoiding that the damper clamp is stressing the optical part of the cable. For optical fibre aerial cables with right-hand outer layer, cableguards with left-hand layer are always used in order to avoid a torsion of the cable by the helical dead end with right-hand layer. A torsion of the aerial cable is causing an enlenghtening leading to a destruction of the optical part of the cable.

The helical rods can be wrapped on by hand in bundles. Tools are not required for the assembly. Prior to installation the cable must be cleaned along the overall lenght of protection rods.


1 ..... Thimble 2 ..... Protection rods 3 ..... Helical dead end

Remarks:

Order example: RW 237 350 s

These protection rods designs are only suitable for cables with right-hand lay armoring and ADSS cables. If dead ends for left-hand lay cables are required this must be specifically stated when placing the order.


ONLINE-CATALOGUE

36 / 117

B813/1 Helical dead ends (AG) for OPGW


RIBE-Order-No. Clamping range

mm Dia. of rods L

1

mm

L2

mm

No. of rods Thimble

RIBE-No. Mass/ pcs

kg

AG 165 103 14,5 - 16,5 2,59 1030 1080 8 0,72

AG 172 111 15,2 - 17,2 2,59 1110 1160 8 0,78

AG 193 117 17,3 - 19,3 3,02 1170 1220 8 F 2685/3 1,16

AG 214 122 19,4 - 21,4 3,02 1220 1270 9 1,38

AG 225 128 20,5 - 22,5 3,02 1280 1330 10 1,59

AG 237 135 21,7 - 23,7 3,51 1350 1400 9 2,03

AG 252 143 23,2 - 25,2 3,51 1430 1490 10 2,39

AG 270 150 25,0 - 27,0 3,51 1500 1560 10 F 2686/2 2,51

AG 285 160 26,5 - 28,5 3,51 1600 1660 11 2,94

AG 305 173 28,5 - 30,5 3,51 1730 1790 11 3,17

AG 326 199 30,6 - 32,6 4,37 1990 2050 9 F 3246/2

Material: Helical rods: Steel, h.d.g. Thimble: Malleable cast iron, h.d.g.


Remarks:


Order example: AG 165 103 lis Thimbles: see data-sheet B821

When selecting the helical dead ends the total diameter resulting out of the cable diameter plus two times the rod diameter of the protection rods has to be taken into account. Furthermore the rated forces of thimbles are observed (see data-sheet B821). These dead end designs are only suitable for cables of right-hand lay armoring. If dead ends for left-hand lay cables are required this must be specifically stated when placing the order.

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ Helical dead ends (AG) for OPGW/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

37 / 117

B813/2 AG-Helical dead ends for short span lengths (up to 70 m) and ADSS

1 ..... Thimble 2 ..... Helical dead end 3 ..... Black crossing mark

RIBE-Orderno. Clamping range Dia. of rods L No. of rods Thimble Thimble Mass/pcs mm mm mm Sheet metal casted kg

AG 083 039 s 7,71 - 8,31 2,18 395 4 B 822 002 0,10AG 089 043 s 8,32 - 8,99 2,54 430 4 B 822 002 0,15AG 097 046 s 9,00 - 9,72 2,54 465 4 B 822 002 0,16AG 105 050 s 9,73 - 10,51 2,54 500 4 B 822 002 0,17AG 113 054 s 10,52 - 11,36 2,54 540 5 B 822 002 0,23AG 122 058 s 11,37 - 12,28 3,02 585 4 B 822 002 0,28

AG 132 058 s 12,29 - 13,27 3,02 580 5 F 10 186 F 2685/3 0,35AG 143 063 s 13,28 - 14,35 3,02 630 5 F 10 186 F 2685/3 0,38AG 155 068 s 14,36 - 15,50 3,51 680 5 F 10 186 F 2685/3 0,56AG 167 073 s 15,51 - 16,75 3,51 735 5 F 10 186 F 2685/3 0,60

AG 181 079 s 16,76 - 18,11 3,51 795 5 F 10 187 F 2685/3 0,65AG 195 086 s 18,12 - 19,57 3,51 860 5 F 10 187 F 2685/3 0,70AG 211 092 s 19,58 - 21,14 3,51 925 6 F 10 187 F 2685/3 0,90AG 228 100 s 21,15 - 22,84 3,51 1000 6 F 10 187 F 2685/3 0,97

AG 246 108 s 22,85 - 24,68 3,51 1080 7 after inquiry F 2685/3 1,22AG 266 117 s 24,69 - 26,67 3,51 1170 7 after inquiry F 2685/3 1,32AG 288 126 s 26,68 - 28,80 3,51 1265 8 after inquiry F 2685/3 1,64

Material: Helical rods: Steel, h.d.g. Thimble: Steel,h.d.g.; malleable cast iron, h.d.g.

Application: These dead ends are designed for the full tensioning of ADSS cables in short span lengths up to 70 m. The loop of the dead end can be protected against abrasion by a thimble.

Stand: 07. Oktober 2008Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends for short span lengths (up to 70 m) and ADSS/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

38 / 117


Remarks: For installation follow RIBE-Mounting Instruction No. 9. Furthermore the rated forces of thimbles are observed (see data-sheet B821). Thimbles: see data-sheet B821-B822

Stand: 07. Oktober 2008Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends for short span lengths (up to 70 m) and ADSS/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

39 / 117

B813/3 AG-Helical dead ends for all span lengths

1 ..... Helical dead end 2 ..... Red crossing mark 3 ..... Black crossing mark

RIBE-Order-No. Clamping range

mm

Dia. of rods

mm

L

mm

No. of rods Thimble

Sheet metal Thimble

casted Mass/ pcs

kg

AG 097 062 s 9,00 - 9,72 2,54 620 4 B 822 002 0,21

AG 105 067 s 9,73 - 10,51 2,54 670 4 B 822 002 0,23

AG 113 072 s 10,52 - 11,36 2,54 725 5 B 822 002 0,29

AG 122 078 s 11,37 - 12,28 3,02 785 4 B 822 002 0,38

AG 132 079 s 12,29 - 13,27 3,02 795 5 F 10186 F 2685/3 0,48

AG 143 086 s 13,28 - 14,35 3,02 860 5 F 10186 F 2685/3 0,52

AG 155 093 s 14,36 - 15,50 3,51 930 5 F 10186 F 2685/3 0,76

AG 167 100 s 15,51 - 16,75 3,51 1005 5 F 10186 F 2685/3 0,82

AG 181 108 s 16,76 - 18,11 3,51 1085 5 F 10187 F 2685/3 0,88

AG 195 117 s 18,12 - 19,57 3,51 1175 5 F 10187 F 2685/3 0,96

AG 211 126 s 19,58 - 21,14 3,51 1265 6 F 10187 F 2685/3 1,23

AG 228 137 s 21,15 - 22,84 3,51 1370 6 F 10187 F 2685/3 1,33

AG 246 148 s 22,85 - 24,68 3,51 1480 7 F 10187 F 2685/3 1,68

AG 266 160 s 24,69 - 26,67 3,51 1600 7 F 10187 F 2685/3 1,81

AG 288 172 s 26,68 - 28,81 3,51 1725 8 F 10187 F 2685/3 2,23

AG 311 186 s 28,82 - 31,13 3,51 1865 8 F 10187 F 2685/3 2,41

Material: Helical rods: Steel, h.d.g. Thimble: Steel, h.d.g.; malleable cast iron, h.d.g.

Application: These dead ends are particulary designed for the full tensioning of ADSS cable in short, medium and long spans. Three ways of application are possible:

for short spans (up to approx. 70m) and small forces: : The dead end is mounted on the cable starting at the black crossing mark. This leads to a long cable loop and a large bending radius of the cable. A thimble can be used in the loop of the dead end.

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends for all span lengths/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

40 / 117

for medium spans (approx. 70 - 150 m) and high forces: The dead end is mounted on the cable starting at the red crossing mark. This leads to a short cable loop. Additional intermediate fittings for installation at the tower and a thimble are necessary.

for long spans and high forces:

Remarks:

Sheet thimbles: see data-sheet B822 Casted thimbles: see data-sheet B821

The use of protection rods (URA: see data-sheet B814/1) is recommended. When selecting the helical dead ends the total diameter resulting out of the cable diameter plus two times the rod diameter of protection rods has to be taken into account.

For installation follow RIBE-Mounting Instruction No. 9. Furthermore the rated forces of thimbles are observed (see data-sheet B821).

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends for all span lengths/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

41 / 117

B813/4 AG-Helical dead ends for Figure-8-cables with separate left-hand layer support

1 ..... Helical dead end 2 ..... Supporting cable 3 ..... Black crossing mark

RIBE-Order-No. For steel support cable Color of marker Dia. of rods L No. of rods Mass/

pcs

No. of wires Dia. without insulation

mm mm mm kg

AG 030 032 li 7 x 1,0 mm 3,0 black 1,55 315 3 0,04

AG 040 043 li 10 x 1,0 mm 4,0 yellow 1,78 425 4 0,07

AG 044 046 li 14 x 1,0 mm 4,4 blue 1,78 455 4 0,08

AG 050 052 li 19 x 1,0 mm 5,0 red 2,18 515 4 0,14

AG 062 061 li 19 x 1,2 mm 6,0 green 2,18 605 5 0,20

AG 076 069 li 19 x 1,5 mm 7,5 orange 2,54 690 5 0,31


Application:

These dead ends are designed for the full tensioning of the separate support cable (left-hand outer layer). The advantage of dead ends compared with tensioning devices commonly used is that there is no bending of the relatively stiff supporting cable. It is recommended to protect the dead end loop from abrasion by means of a thimble. These dead ends can be used to suspend self supporting figure-8-cables too. Two dead ends per suspension point are required for any such application (see figure below).

Fig.: Mounting example for suspending self supporting cables

Installation: Dead ends can be installed and removed quickly and without application of any tools. Wrapping of dead ends starts at the crossing

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends for Figure-8-cables with separate left-hand layer support/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

42 / 117

mark. For installation follow RIBE-Mounting Instruction No. 9.

Remarks:

Thimbles: see data-sheet B822

These dead end designs are only suitable for left-hand layer steel support cables. When placing an order please state if dead ends for righthand layer support cables are required.

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends for Figure-8-cables with separate left-hand layer support/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

43 / 117

B813/6 AG-Helical dead ends


AG 121 075 s 11,50 - 12,13 3,51 755 805 5 0,62

AG 128 080 s 12,14 - 12,81 3,51 800 850 6 F 2685/3 0,79

AG 135 084 s 12,82 - 13,53 3,51 845 895 6 0,84

AG 142 089 s 13,54 - 14,28 3,51 890 1040 6 0,88

AG 150 094 s 14,29 - 15,08 3,51 940 990 6 0,93

AG 159 099 s 15,09 - 15,92 3,51 990 1040 6 0,97

AG 168 098 s 15,93 - 16,80 3,51 980 1030 6 0,96

AG 177 103 s 16,81 - 17,74 3,51 1035 1085 6 F 2685/3 1,01

AG 187 109 s 17,75 - 18,72 3,51 1095 1145 7 1,25

AG 197 115 s 18,73 - 19,76 3,51 1155 1205 7 1,32

AG 208 122 s 19,77 - 20,86 4,37 1220 1270 6 1,86

AG 220 128 s 20,87 - 22,02 4,37 1285 1335 6 1,95

AG 232 136 s 22,03 - 23,24 4,37 1360 1420 6 2,06

AG 245 143 s 23,25 - 24,53 4,37 1435 1495 7 2,54

AG 258 151 s 24,54 - 25,89 4,37 1515 1575 7 F 2686/2 2,67

AG 273 159 s 25,90 - 27,32 4,37 1595 1755 7 2,81

AG 288 168 s 27,33 - 28,84 4,37 1685 1745 8 3,39

AG 304 178 s 28,85 - 30,43 4,37 1780 1840 8 3,58

AG 321 187 s 30,44 - 32,12 4,37 1875 1945 9 4,24

AG 338 198 s 32,13 - 33,89 4,37 1980 2050 9 F 3246/2 4,47

AG 357 209 s 33,90 - 35,77 5,18 2090 2160 10 7,38

AG 377 220 s 35,78 - 37,75 5,18 2205 2275 10 7,78

RIBE-Order-No. Clamping range Dia. of rods L1

mm

L2

mm

No. of rods Thimble

RIBE-No. Mass/ pcs

kg

Material: Helical rods: Steel, h.d.g. Thimble: Malleable cast iron, h.d.g.

Stand: 04. Mai 2007Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

44 / 117


Remarks:


Order example: AG 177 103 s Thimbles: see data-sheet B821

When selecting helical dead ends the total diameter resulting from the cable diameter plus two times the rod diameter of the protection rods has to be taken into account. Furthermore the rated forces of thimbles are observed (see data-sheet B821). These dead end designs are only suitable for cables with right-hand lay armoring and ADSS cables. If dead ends for left-hand lay cables are required this must specifically be stated when placing the order.

Stand: 04. Mai 2007Pfad: Optofit/ Fittings for tension towers/ AG-Helical dead ends/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

45 / 117

B814/1 URA-Protection rods for ADSS cables and spans longer than 150 m

RIBE-Order-No. Clamping range Dia. of rods No. of rods Subsets Mass/

pcs

mm mm mm kg

URA 077 110 lis 7,35 - 7,79 2,59 1105 10 3-3-4 0,17

URA 082 114 lis 7,80 - 8,27 2,59 1141 10 3-3-4 0,18

URA 087 117 lis 8,28 - 8,78 2,59 1180 11 3-4-4 0,20

URA 093 122 lis 8,79 - 9,31 2,59 1221 11 3-4-4 0,21

URA 098 126 lis 9,32 - 9,88 2,59 1264 12 4-4-4 0,23

URA 104 131 lis 9,89 - 10,49 2,59 1310 13 4-4-5 0,26

URA 111 141 lis 10,50 - 11,13 3,07 1416 12 4-4-4 0,37

URA 118 146 lis 11,14 - 11,80 3,07 1468 12 4-4-4 0,38

URA 125 152 lis 11,81 - 12,52 3,07 1523 13 4-4-5 0,43

URA 132 158 lis 12,53 - 13,28 3,07 1581 13 4-4-5 0,44

URA 140 168 lis 13,29 - 14,09 3,45 1688 13 4-4-5 0,60

URA 149 175 lis 14,10 - 14,95 3,45 1753 14 4-5-5 0,67

URA 158 182 lis 14,96 - 15,86 3,45 1823 14 4-5-5 0,69

URA 168 189 lis 15,87 - 16,82 3,45 1896 15 5-5-5 0,77

URA 178 200 lis 16,83 - 17,84 3,70 2004 15 5-5-5 0,94

URA 189 208 lis 17,85 - 18,92 3,70 2086 16 4-4-4-4 1,04

URA 200 217 lis 18,93 - 20,06 3,70 2173 16 4-4-4-4 1,08

URA 212 226 lis 20,07 - 21,28 3,70 2266 17 4-4-4-5 1,20

URA 225 236 lis 21,29 - 22,57 3,70 2364 18 4-4-5-5 1,32

Material: Helical rods: Aluminium alloy

Application:

Cable guards protect the ADSS cables at the tension assembly. They are mounted under the helical dead end and reduce the radial forces in the cable - especially at the loopside of the dead end. Radial forces (depending on the tension force) can stress the optical part of the cable inadmissibly. This can cause high damping in the optical fibre. This results in a high signal damping in the optical fibre up to an interruption of the optical transmission.

Installation: The helical rods can be wrapped on by hand in bundles. Tools are not required for installation.

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ URA-Protection rods for ADSS cables and spans longer than 150 m/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

46 / 117


1 ..... Thimble 2 ..... Protection rods 3 ..... Helical dead end

Remarks: Helical dead ends: see data-sheet B813/3 Order example: URA 077 110 lis

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ URA-Protection rods for ADSS cables and spans longer than 150 m/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

47 / 117

B814/2 UTA-Protection rods for ADSS cables and medium span lengths (70 - 150 m)

RIBE-Order-No. Clamping range Dia. of rods No. of rods Subsets Mass/ pcs

mm mm mm kg

UTA 077 125 lis 7,35 - 7,79 2,59 1254 10 3-3-4 0,20

UTA 082 126 lis 7,80 - 8,27 2,59 1270 10 3-3-4 0,20

UTA 087 128 lis 8,28 - 8,78 2,59 1287 11 3-4-4 0,22

UTA 093 130 lis 8,79 - 9,31 2,59 1304 11 3-4-4 0,22

UTA 098 132 lis 9,32 - 9,88 2,59 1323 12 4-4-4 0,24

UTA 104 134 lis 9,89 - 10,49 2,59 1342 13 4-4-5 0,27

UTA 111 164 lis 10,50 - 11,13 3,07 1643 12 4-4-4 0,43

UTA 118 166 lis 11,14 - 11,80 3,07 1665 12 4-4-4 0,43

UTA 125 168 lis 11,81 - 12,52 3,07 1689 13 4-4-5 0,47

UTA 132 171 lis 12,53 - 13,28 3,07 1714 13 4-4-5 0,48

UTA 140 174 lis 13,29 - 14,09 3,45 1740 13 4-4-5 0,62

UTA 149 176 lis 14,10 - 14,95 3,45 1768 14 4-5-5 0,67

UTA 158 179 lis 14,96 - 15,86 3,45 1798 14 4-5-5 0,68

UTA 168 229 lis 15,87 - 16,82 3,45 2299 15 5-5-5 0,94

UTA 178 233 lis 16,83 - 17,84 3,70 2332 15 5-5-5 1,09

UTA 189 327 lis 17,85 - 18,92 3,70 3278 16 4-4-4-4 1,63

UTA 200 331 lis 18,93 - 20,06 3,70 3315 16 4-4-4-4 1,65

UTA 212 335 lis 20,07 - 21,28 3,70 3355 17 4-4-4-5 1,77


Application:

Installation: The helical rods can be wrapped on by hand in bundles. Tools are not required for installation.

Protection rods are mounted under the suspension rods to protect the ADSS cable. They reduce radial forces in the cable and increase - due to the increased bending stiffness - the bending radius of the ADSS cable.


Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ UTA-Protection rods for ADSS cables and medium span lengths (70 - 150 m)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

48 / 117

1 ..... UTA-Protection rods 2 ..... Hook 3 ..... TG-Suspension rods

Remarks: Order example: UTA 077 125 lis Suspension rods: see data-sheet B805/2 Installation instructions: see data-sheet Mon69

Stand: 10. August 2006Pfad: Optofit/ Fittings for tension towers/ UTA-Protection rods for ADSS cables and medium span lengths (70 - 150 m)/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

49 / 117

B814/3 Patch rods

RIBE-Order-No. Clamping range Dia. of rods L No. of rods Subsets Mass/ pcs

mm mm mm kg

RA 077 113 s 7,35 7,79 2,59 1136 10 3 - 3 4 (*) 0,18

RA 082 117 s 7,80 - 8,27 2,59 1175 10 3 - 3 - 4 (*) 0,18

RA 087 121 s 8,28 8,78 2,59 1216 11 3 - 4 - 4 (*) 0,21

RA 093 126 s 8,79 - 9,31 2,59 1260 11 3 - 4 - 4 (*) 0,21

RA 098 130 s 9,32 9,88 3,07 1307 10 3 - 3 - 4 (*) 0,28

RA 104 135 s 9,89 10,49 3,07 1356 11 3 - 4 - 4 (*) 0,32

RA 111 140 s 10,50 11,13 3,45 1408 11 3 - 4 - 4 (*) 0,43

RA 118 146 s 11,14 - 11,80 3,45 1463 11 3 - 4 - 4 (*) 0,44

RA 125 152 s 11,81 12,52 3,45 1522 11 3 - 4 - 4 (*) 0,46

RA 132 158 s 12,53 13,28 4,24 1584 10 3 - 3 - 4 (*) 0,66

RA 140 165 s 13,29 14,09 4,24 1650 11 3 - 4 - 4 (*) 0,75

RA 149 172 s 14,10 14,95 4,62 1720 11 3 - 4 - 4 (*) 0,93

RA 158 179 s 14,96 15,86 4,62 1794 11 3 - 4 - 4 (*) 0,97

RA 168 187 s 15,87 16,82 4,62 1873 12 4 - 4 - 4 (*) 1,10

RA 178 195 s 16,83 17,84 5,18 1956 11 3 - 4 - 4 (*) 1,33

RA 189 204 s 17,85 18,92 6,35 2044 10 3 - 3 - 4 (*) 1,91

RA 200 213 s 18,93 20,06 6,35 2138 10 3 - 3 - 4 (*) 1,99

RA 212 223 s 20,07 21,28 6,35 2237 11 3 - 4 - 4 (*) 2,29

RA 225 234 s 21,29 22,57 6,35 2342 11 3 - 4 - 4 (*) 2,39

RA 239 245 s 22,58 23,93 7,87 2453 10 (**) 3,52

RA 253 257 s 23,94 25,38 7,87 2571 10 (**) 3,68

RA 269 269 s 25,39 26,91 7,87 2696 11 (**) 4,24

RA 285 282 s 26,92 28,54 9,27 2829 10 (**) 5,63

RA 302 296 s 28,55 30,26 9,27 2970 11 (**) 6,48

RA 320 311 s 30,27 32,08 9,27 3119 11 (**) 6,79

RA 340 327 s 32,09 34,02 9,27 3277 12 (**) 7,77

(*) Subsets sanded inside with a small grained metallic (conductive) oxide

(**) Single rods (not sanded), 250 g friction bond a part of delivery


Application:

Installation:

Patch rods are used to repair damaged OPGW (up to 100 % of the outside layer) and are preferably employed in the free span. Patch rods are capable to restore the electrical conductivity and mechanical strength securing thus the full performance of OPGW. The length of the patch rods was determined in such a way, that a damaged place up to 50 cm is covered. In case of larger damaged areas longer special rods are necessary.

Stand: 06. Februar 2007Pfad: Optofit/ Fittings for tension towers/ Patch rods/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

50 / 117


he helical rods can be wrapped on by hand in bundles. Tools are not required for installation. The rods have to be installed in such a way that the middle mark of the rods are in the center of the damaged area. Rods of diameters of more than 7 mm must singly be wrapped on. Prior to wrapping on the single rods, the outer layer of OPGW must be cleaned and be covered with friction bond. The friction bond is enclosed on delivery.

Stand: 06. Februar 2007Pfad: Optofit/ Fittings for tension towers/ Patch rods/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

51 / 117

B816/1 Tension supports for optical fibre aerial cables and ACSR conductors

1 ..... Boreholes for parallel groove clamp on request. Dimensions are required!

RIBE-Order-No. Rated force Mass/ pcs Remarks

d FN

mm kN kg

F 13 804/1 20

F 13 804/2 24 150 3,9

F 13 804/3 --- - without double eyes, including boreholes for parallel groove clamp (M12, a = 50 mm)

F 13 804/4 20 - including boreholes for parallel groove clamp (M12, a = 50 mm)

Material: Support: Malleable cast iron, h.d.g. Double eyes: Forged steel, h.d.g. Bolts: Steel, grade 8.8, h.d.g.

Application:

Remark: For other executions please inquire.

Tension supports are used to tension optical fibre aerial cables and ACSR conductors. They are typically applied on top of tension towers.

Stand: 26. Juli 2007Pfad: Optofit/ Fittings for tension towers/ Tension supports for optical fibre aerial cables and ACSR conductors/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

52 / 117

B816/2 Tension supports with parallel groove clamps for optical fibre aerial cables and ACSR conductors

1 ..... Groove A 2 ..... Groove B

B 816 005/1 A... B... Kb 1 8,00 - 8,5 1 8,00 - 8,5

B 816 005/1 A... B... Kb 2 8,51 - 9,0 2 8,51 - 9,0

B 816 005/1 A... B... Kb 3 9,01 - 9,5 3 9,01 - 9,5

B 816 005/1 A... B... Kb 4 9,51 - 10,0 4 9,51 - 10,0

B 816 005/1 A... B... Kb 5 10,01 - 10,5 5 10,01 - 10,5

B 816 005/1 A... B... Kb 6 10,51 - 11,0 6 10,51 - 11,0

B 816 005/1 A... B... Kb 7 11,01 - 11,5 7 11,01 - 11,5

B 816 005/1 A... B... Kb 8 11,51 - 12,0 8 11,51 - 12,0

B 816 005/1 A... B... Kb 9 12,01 - 12,5 9 12,01 - 12,5

B 816 005/1 A... B... Kb 10 12,51 - 13,0 10 12,51 - 13,0

B 816 005/1 A... B... Kb 11 13,01 - 13,5 11 13,01 - 13,5

B 816 005/1 A... B... Kb 12 13,51 - 14,0 12 13,51 - 14,0

B 816 005/1 A... B... Kb 13 14,01 - 14,5 13 14,01 - 14,5

B 816 005/1 A... B... Kb 14 14,51 - 15,0 14 14,51 - 15,0

B 816 005/1 A... B... Kb 15 15,01 - 15,5 15 15,01 - 15,5

B 816 005/1 A... B... Kb 16 15,51 - 16,0 16 15,51 - 16,0

RIBE-Order-No.. Clamping range of groove A Clamping range of groove B Mass/ pcs Exe. mm Exe. mm kg

Stand: 26. Juli 2007Pfad: Optofit/ Fittings for tension towers/ Tension supports with parallel groove clamps for optical fibre aerial cables and ACSR conductors/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

53 / 117

B 816 005/1 A... B... Kb 17 16,01 - 16,5 17 16,01 - 16,5

B 816 005/1 A... B... Kb 18 16,51 - 17,0 18 16,51 - 17,0

B 816 005/1 A... B... Kb 19 17,01 - 17,5 19 17,01 - 17,5

B 816 005/1 A... B... Kb 20 17,51 - 18,0 20 17,51 - 18,0

B 816 005/1 A... B... Kb 21 18,01 - 18,5 21 18,01 - 18,5

B 816 005/1 A... B... Kb 22 18,51 - 19,0 22 18,51 - 19,0

B 816 005/1 A... B... Kb 23 19,01 - 19,5 23 19,01 - 19,5

B 816 005/1 A... B... Kb 24 19,51 - 20,0 24 19,51 - 20,0

B 816 005/1 A... B... Kb 25 20,01 - 20,5 25 20,01 - 20,5

B 816 005/1 A... B... Kb 26 20,51 - 21,0 26 20,51 - 21,0

B 816 005/1 A... B... Kb 27 21,01 - 21,5 27 21,01 - 21,5

B 816 005/1 A... B... Kb 28 21,51 22,0 28 21,51 22,0

B 816 005/1 A... B... Kb 29 22,01 - 22,5 29 22,01 - 22,5

RIBE-Order-No.. Clamping range of groove A Clamping range of groove B Mass/ pcs Exe. mm Exe. mm kg

Material: Support: Malleable cast iron, h.d.g. Double eyes: Forged steel, h.d.g. Bolts: Steel, grade 8.8, h.d.g. Clamp body: Aluminium, forged Bolts, nuts: M10, stainless steel

Application:

Remarks: Recommended tightening torque of bolts, M10: 46 Nm

Order example: Groove A: 15,8 mm dia. Groove B: 21,2 mm dia. Parallel groove clamp: B 816 005/1 A16 B27 Kb For other executions please inquire. Filler bolts: see data-sheet B816/3

Tension supports are used to tension and earthing optical fibre aerial cables and ACSR conductors. They are typically applied on top of tension towers.

The exact diameter of grooves A and B are needed when placing an order of tension support with parallel groove clamp acc. to RIBE-No. B 816 005.


1 ..... OPGW 2 ..... Tension support with parallel groove clamp 3 ..... Filler bolt


ONLINE-CATALOGUE

54 / 117

B816/3 Filler bolts for tension supports with parallel groove clamps

Clamping range RIBE-Order-No. d Mass/ pcs Clamping range RIBE-Order-No. d Mass/ pcsmm mm kg mm mm kg

8,00 - 8,5 B 816 005-01/01 7,9 16,51 - 17,0 B 816 005-01/18 16,4 8,51 - 9,0 B 816 005-01/02 8,4 17,01 - 17,5 B 816 005-01/19 16,9 9,01 - 9,5 B 816 005-01/03 8,9 17,51 - 18,0 B 816 005-01/20 17,4 9,51 - 10,0 B 816 005-01/04 9,4 18,01 - 18,5 B 816 005-01/21 17,9 10,01 - 10,5 B 816 005-01/05 9,9 18,51 - 19,0 B 816 005-01/22 18,4 10,51 - 11,0 B 816 005-01/06 10,4 19,01 - 19,5 B 816 005-01/23 18,9 11,01 - 11,5 B 816 005-01/07 10,9 19,51 - 20,0 B 816 005-01/24 19,4 11,51 - 12,0 B 816 005-01/08 11,4 20,01 - 20,5 B 816 005-01/25 19,9 12,01 - 12,5 B 816 005-01/09 11,9 20,51 - 21,0 B 816 005-01/26 20,4 12,51 - 13,0 B 816 005-01/10 12,4 21,01 - 21,5 B 816 005-01/27 20,9 13,01 - 13,5 B 816 005-01/11 12,9 21,51 - 22,0 B 816 005-01/28 21,4 13,51 - 14,0 B 816 005-01/12 13,4 22,01 - 22,5 B 816 005-01/29 21,9 14,01 - 14,5 B 816 005-01/13 13,9 22,51 - 23,0 B 816 005-01/30 22,4 14,51 - 15,0 B 816 005-01/14 14,4 23,01 - 23,5 B 816 005-01/31 22,9 15,01 - 15,5 B 816 005-01/15 14,9 23,51 - 24,0 B 816 005-01/32 23,4 15,51 - 16,0 B 816 005-01/16 15,4 24,01 - 24,5 B 816 005-01/33 23,9 16,01 - 16,5 B 816 005-01/17 15,9

Material: Filler bolt: Aluminium alloy

Application: Insert filler bolt in the second groove of the parallel groove clamp in case of earthing of one optical fibre aerial cable on the top of the tower.

Remarks: Tension supports with parallel groove clamps: see data-sheet B816/2 and B816/4 For other executions please inquire.

Stand: 09. Februar 2009Pfad: Optofit/ Fittings for tension towers/ Filler bolts for tension supports with parallel groove clamps/Gedruckt am: 08. Januar 2010

ONLINE-CATALOGUE

55 / 117

B816/4 Tension supports with parallel groove clamps for optical fibre aerial cables and ACSR conductors

1 ..... Groove A 2 ..... Groove B

B 816 005/2 A... B... Kb 1 8,00 - 8,5 1 8,00 - 8,5

B 816 005/2 A... B... Kb 2 8,51 - 9,0 2 8,51 - 9,0

B 816 005/2 A... B... Kb 3 9,01 - 9,5 3 9,01 - 9,5

B 816 005/2 A... B... Kb 4 9,51 - 10,0 4 9,51 - 10,0

B 816 005/2 A... B... Kb 5 10,01 - 10,5 5 10,01 - 10,5

B 816 005/2 A... B... Kb 6 10,51 - 11,0 6 10,51 - 11,0

B 816 005/2 A... B... Kb 7 11,01 - 11,5 7 11,01 - 11,5

B 816 005/2 A... B... Kb 8 11,51 - 12,0 8 11,51 - 12,0

B 816 005/2 A... B... Kb 9 12,01 - 12,5 9 12,01 - 12,5

B 816 005/2 A... B... Kb 10 12,51 - 13,0 10 12,51 - 13,0

B 816 005/2 A... B... Kb 11 13,01 - 13,5 11 13,01 - 13,5

B 816 005/2 A... B... Kb 12 13,51 - 14,0 12 13,51 - 14,0

B 816 005/2 A... B... Kb 13 14,01 - 14,5 13 14,01 - 14,5

B 816 005/2 A... B... Kb 14 14,51 - 15,0 14 14,51 - 15,0

B 816 005/2 A... B... Kb 15 15,01 - 15,5 15 15,01 - 15,5

B 816 005/2 A... B... Kb 16 15,51 - 16,0 16 15,51 - 16,0

RIBE-Order-No. Clamping range of groove A Clamping range of groove B Mass/ pcs Exe. mm Exe. mm kg


ONLINE-CATALOGUE

56 / 117

B 816 005/2 A... B... Kb 17 16,01 - 16,5 17 16,01 - 16,5

B 816 005/2 A... B... Kb 18 16,51 - 17,0 18 16,51 - 17,0

B 816 005/2 A... B... Kb 19 17,01 - 17,5 19 17,01 - 17,5

B 816 005/2 A... B... Kb 20 17,51 - 18,0 20 17,51 - 18,0

B 816 005/2 A... B... Kb 21 18,01 - 18,5 21 18,01 - 18,5

B 816 005/2 A... B... Kb 22 18,51 - 19,0 22 18,51 - 19,0

B 816 005/2 A... B... Kb 23 19,01 - 19,5 23 19,01 - 19,5

B 816 005/2 A... B... Kb 24 19,51 - 20,0 24 19,51 - 20,0

B 816 005/2 A... B... Kb 25 20,01 - 20,5 25 20,01 - 20,5

B 816 005/2 A... B... Kb

b08 ovjesna oprema za optiku.pdf

Documents

optical fibre cable

optical damping

integrated optical fibres

oppw aerial cables

formed fittings

different cables

formed accessories

optical signal damping