baofeng uv-5r programming electronics
DESCRIPTION
Baofeng UV-5R Programming ElectronicsTRANSCRIPT
-
14.05.2014 8.29.27Technical Baofeng Pofung UV5R UV82 UV82X
Page 1 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
Hardware / Technical
Speaker Microphone Pin Out
Dual PTT Switching
Programming Cable
SMA Antenna Connection
Extended Antenna Threads
Cloning Cables
Erratic Charger Behavior
US Sales and Warranty Support
HandheldRadios
Mobile Radios
CABLESFTDI CABLE
6 in 1 Cable
ACCESSORIES
BATTERIESand
AA CASES
ANTENNAS
POUCHES
SOFT CASE
TEST EQUIPMENT
PIGTAILS
ADAPTORS
Speaker Microphone Pin Out
3.5mm Plug Sleeve Mic PTT Rx Data (to the radio)Ring Mic +Tip +V (from the radio)
2.5mm Plug
Sleeve Speaker PTT Data GNDRing TX Data (from the radio)Tip Speaker + Connect Sleeve to Sleeve for PTT
Note: This plug is Baofeng, Kenwood and Wouxun compatible.
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 2 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
Study Guides& Handbooks
HAM RADIOfor DUMMIES
HandheldRadios
Mobile Radios
CABLESFTDI CABLE
6 in 1 Cable
ACCESSORIES
BATTERIESand
AA CASES
ANTENNAS
POUCHES
SOFT CASE
TEST EQUIPMENT
PIGTAILS
Graphic by electronicholas
Dual PTT SwitchBaofeng UV-82 series
A standard single button remote spkr/micr will select Display B (the bottomdisplay) when keyed.
There are earpiece/microphones available that incorporate two PTT buttons.The wiring configuration for these is shown below.
Shorting X to A will select Display A (upper)Shorting X to B will select Display B (lower)
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 3 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
ADAPTORS
Study Guides& Handbooks
HAM RADIOfor DUMMIES
PROGRAMMING CABLESfor Kenwood, Wouxun, Baofeng
Provided by Jim KC9HI, Paul AE5JU
The RXD line from the module goes to the sleeve of the 3.5MM plug.
The TXD line from the module goes to the ring of the 2.5MM plug.
The GND line from the module goes to the sleeve of the 2.5MM plug.
There are several variations of CP2102 boards available. The pin location and labels may vary.
Below are two examples.
Builders Note: Some boards have the TXD and RXD pin labels reversed. If yourcable does not work, switch the TXD and RXD wires.
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 4 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
The CP2102 USB-UART is by Silicon Labs and can be found on eBay ($3).A 6ft Cable and Plug can be obtained from 3_Old_Crows ($8).
Windows, MAC and Linux drivers can be downloaded at: Silabs_Drivers
Builders Note: Using an old Cloning or Programming Cable/Plug may not work. The wires are hair thin and many can't be soldered.
Using the TOC cable: White=TXD Blue=RXD Black=GroundCheck continuity before soldering
PROGRAMMING CABLES
for Baofeng UV-3R
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 5 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
ANTENNA CONNECTION
Most Baofeng UV-5R, UV-82, UV-B5/6, UV-3R+, etc
require an antenna with an SMA Female fitting.Most Wouxun KG-UVxx models require an SMA Male fitting.
Unlike horseshoes, close doesn't count.Always confirm the connector type before ordering.
example of SMA Female
SMA RP (Reverse Polarity) and SMA Male are NOT compatible.
Note: SMA-RP connectors are found on most Wi-Fi Routers.
Examples of Various SMA Formats
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 6 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
Why this is referred to as a Reversed Connector
Reversed SMA-Male Connectors arecommonly found on Wi-Fi Routers
To use an antenna with a BNC Male requires the following adapter:
SMA Female (above) to mate with the radio BNC Female to mate with the BNC Male antenna.
Another option is a jumper (pigtail). This relieves the stress of a heavier cablewhen using an external mobile or fixed antenna.
Cable Jumper (pigtails) are available from 3_Old_Crows
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 7 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
SMA-F Antenna Extended Threads
Some antennas with SMA-F connectors have an extended thread. Most radiossuch as the UV-5R and UV-3R+ require a standard SMA-F. The illustration shows two different Nagoya NA-771 antennas. Some antennas with extended threads ship with a spacer to fill the gap.
If the radio requires extended threads, such as a BF-888S, an antenna withstandard threads will not make connection unless you trim the outer shell or lipof the antenna so it is flush with the base.
The wrong threads (if too short) will result in poor reception and over heating ofthe transmitter as there is no antenna connection.
CLONING CABLES
Cloning Cables are used to pass programming information from one handheld toanother without the use of software.
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 8 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
These cables can be found on Amazon.com
(Kenwood Cable Copy)
Cloning Process for the UV5R can be found HERE.
Cloning Process for the UV82 can be found HERE.
Erratic Charger Behavior
This includes: Battery not charging, Light staying Red and Erratic Light behavior. On many chargers, internal contact to the circuit board is made via tension clips.If there clips do not have the proper tension or the copper pad is not clean or isoxidized, a good contact will not be made. This is normally an easy fix. This brief video will show you the inside of the charger base and a simple fix.
VIDEOby John Reinhart
TOP of PAGE
Miklor Home
-
14.05.2014 8.29.28Technical Baofeng Pofung UV5R UV82 UV82X
Page 9 of 9http://www.miklor.com/COM/UV_Technical.php#progcable
Back
53,694