basic level training process valve

8/12/2019 Basic Level Training Process Valve

1/3

BASIC LEVEL - Pneumatic/Electro Pneumatic SET EQUIPMENT

File: DIDACTIC PT02

PT. Norgantara Surya Gemilang

Wisma SlipiJl. Letjend.S. Parman Kav 128thFloor, Suite 802. Jakarta 11480

Tel. +62 21 5366 1936

Fax. +62 21 530 [email protected]

ENGEENERING ADVANTAGECreating Competitive around the world

Subject Electro Pneumatic Equipments

Program Training Basic Level in Pneumatic/Electro Pneumatic Control Basic Level

Depart. Didactic PT NORGRANTARA SURYA GEMILANGTime

Pneumatic /Electro Pneumatic Equipment Set Basic Level

Description PartNo

Qty. Price (Rp)

Table without compressor 1

Aluminium profile panel (1100 x 700 mm) 1

Learn top-L 1

Quick push-pull distributor 10

Service unit with on off valve 1

Connecting components 1Manifold 1

Red Plastic Tubing 10 m 1

Single Acing Cylinder 1

Double acting cylinder 2

PURE PNEUMATIC CONTROL3/2-way valve with push button, NC 3

3/2-way valve with push button, NO 1

5/2-way valve with selector switch 1

Pressure gauge 2

3/2-way roller lever valve, NC 3

3/2-way roller lever valve with idle return, NC 1

5/2-way single pilot valve 35/2-way double pilot valve 3

Shuttle valve (OR) 1

Dual-pressure valve (AND) 1

Time delay valve, normally closed 1

Quick exhaust valve 1

One-way flow control valve 2

Pressure sequence valve 1

ELECTRO PNEUMATIC CONTROL

Relay, 3 off 2

Electrical Electrical input signal device 1

Time relay unit - two fold 1

Proximity switch + cylinder mounting 2

Limit switch left actuated 1

Limit switch right actuated 1

Pneumatic switch (electrical) 1

3/2 way single solenoid ,NC 1

5/2 way single solenoid 2

5/2 way double solenoid 1Electrical cable @ 30 cm and 50 cm 10

Exercise book- Basic level 2

1. TRAINING PRESPECTIVE:


2/3


File: DIDACTIC PT02



Tel. +62 21 5366 1936



Manufacturing industries are aware more than ever of the need to increase production under qualitycontrolled conditions. With compressed air now a standard form of power, pneumatic equipment in itsindustrial application plays an important role in the practical realization of these needs. In order to gainthe maximum benefits from pneumatic control it is necessary to appreciate its scope and to understandthe fundamental requirements in applying this technology. This in fact is the overall objective of thetraining/course and we trust that all participants may share the benefits derived from a greaterunderstanding of Applied Pneumatics.

2. TRAINING OBJECTIVE:

Some of the basic aims of this pneumatics training are to assist participants in the following:-

Solution to immediate pneumatics problems where possible.

Recognition of pneumatic equipment, components and their functions.

Understanding of pneumatic fluid power symbols and their relation to the equipment function. Recognition of installation and application techniques required for effective and efficient

operation of pneumatic equipment.

An appreciation of the scope and potential of Applied Pneumatics in industry.

Understanding of pneumatic logic control methods.

An appreciation of the range and the potential

.

3. TRAINING CONTENTS:

A. Theoretical review of pneumatic and electro pneumatic control system

Criteria of working media control system Control chain of Pneumatic/Electro Pneumatic System Standard and Symbol

Knowledge of Pneumatic/Electro Pneumatic System Components Pneumatic/Electro Pneumatic Air preparation system Air Distribution system Speed control system

Logic processing in pneumatic/electro pneumatic

B. Software simulation

One Cylinder control system

Parallel motion control system

Two cylinder control system

Multi cylinder control system

C. Realization with pneumatic equipment set

Part 1. Pneumatic Components

Part 2. Pneumatic Applications

Part 3. Electro pneumatic Components

Part 4. Electro Pneumatic Applications

D. Fault Finding and Diagnosing

Exercise 1

Exercise 2


3/3


File: DIDACTIC PT02



Tel. +62 21 5366 1936



TRAINING DURATION:

Complete Basic Level :Total training time for Basic Level is 8 hour that distribution on 7 daysEach day equal to 8 hours not include 2 hours per days for the rest time.The description of each days is bellow :

A. Theoretical of pneumatic/electro pneumatic control system ( 16 hours in 2 days )B. Software simulation ( 8 hours in 1 days)C. Realization with pneumatic equipment set ( 24 hours in 3 days )D. Fault Finding and Diagnosing ( 8 hours in 1 days )

Training Tutution :Industrial Prices : per one days training duration Rp-

1. Packet basic level 7 days Rp,-2. Customize ,minimum one day training is Rp,-

University Prices : per one days training duration Rp,-1. Packet basic level 7 days Rp,-2. Customize ,minimum one day training is Rp,-

basic level training process valve

Documents