belajar edit

Upload: ryan-bahari

Post on 04-Jun-2018

232 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/13/2019 belajar edit

    1/16

    Step 1

    Make a new document that is 2000px by 1200px. Then make a new Gradient Adjustment

    Layerwith a linear gradient that goes from a dark gray (#464646)at the bottom to black

    (#000000)at the top. This will be our background base.

    Step 2

    Make another linear Gradient Adjustment Layerabove the previous one, and make it a

    rainbow of colors of your choice. There are some colorful presets that you can choose from inthe gradient palette, or create your own. Set the layers Fill down to 25%. Then set the layers

    blending mode to Color.

    Tip: When you set the blending mode to color it makes it so the layer only affects the color of

    everything below it, while leaving the lightness/darkness alone.

  • 8/13/2019 belajar edit

    2/16

  • 8/13/2019 belajar edit

    3/16

    Step 3

    Finally make another Gradient Adjustment Layerabove the previous two. This one will be a

    radial gradient. Set this one up so that the only 2 colors in the gradient are black and then makethe transparency go from 100% at one end and 0%at the other end.

    If you see that black is covering the center of the image, check the Reverse box. Then make itso the black goes around the edges of the canvas. Set the layer opacity to 65%. I moved the

    transparency handles around a little to get the exact effect that I wanted.

  • 8/13/2019 belajar edit

    4/16

  • 8/13/2019 belajar edit

    5/16

    Step 4

    Now lets begin with the text treatment. Hit (T) for the type tool, and make a (single click)on

    the canvas. Then type your letter, in my case a P. Then grab the Move tooland (Hit CMD+T)and transform the letter, adjust it until its the size that you want it. Hit (T)again for the type

    tool, and if its not already, make the letter black by clicking the text color box in the property

    bar. Set the letter layers blending mode to Screen. The letter will disappear.

    Step 5

    (Double click)to the right of the letter layers name in the layer palette to bring up the layer

    styles palette. Put an Outer Glow and a Stroke on the layerwith the exact settings that you see

    below. You will see a very faint image of the letter now.

    Lets use this first letter as a starting point for all the text in the image. Once we layer several

    different letters on top of each other, our effect will come to life.

  • 8/13/2019 belajar edit

    6/16

  • 8/13/2019 belajar edit

    7/16

    Step 6

    Duplicate the letter layer by dragging it down to the New Layer buttonat the bottom of the

    layer palette. Select the type tool (T)and then change the font on the new layer. If the new fontdoesnt line up how you want to hit (CMD+T) to free transformthe new letter. Make sure that

    you always line up the baseline of the letters. You can move the anchor point to the base line

    when you are transforming to keep it lined up correctly.

    Now do this step 20 times, each time using a different font. I chose to use all different fonts that

    have serifs. You can use all fonts that are sans-serif if you like, but I wouldnt mix the two.

  • 8/13/2019 belajar edit

    8/16

  • 8/13/2019 belajar edit

    9/16

    Step 7

    Select all the text layers that you have. Then hit (CMD+G)to group them. With the group

    selected in the layer palette, hit (V) for the move tool. Then (while holding ALT), click and

    drag on the letterson the canvas to duplicate them. Dragthem to the right where you want the

    next letter to be. Now there should be 2 groups of text in the layer palette. Turn off all the letterlayers in the new group (except the bottom one) by clicking in the little eye iconnext to eachone.

    Now select the text tool (T), and highlight the single letter. Then change it to the next letter thatyou want, in my case an S. Finally, turn the S layer off. Then turn on the next one and do the

    same. Repeat this until all the letters in your new group are changed. Turn all the layers back on.

    Repeat this step for each new letter you need.

    Step 8

    Select the elliptical marquee tooland make a very thin ellipse at the base of your letters. Then

    Feather the selection about 20px. Enter quickmask mode (Q). Then go to Filter>Blur>Motion

    Blur. Make the angle 0 and the length 700px and hit OK. This gives us a nice fade out to the

    left and right sides. Then exit quickmask mode (Q).

    Now make a curves adjustment layer above the gradients, but below the letter groups. Then

    apply a curve that looks like the one below. This just gives our letters something to sit on.

  • 8/13/2019 belajar edit

    10/16

  • 8/13/2019 belajar edit

    11/16

    Step 9

    Make a new document that is 300px by 300px. Double clickon the background layer to make it

    an active layer. (Double click)to the right of the layer name to open the layer styles palette.Apply a color overlayto make the layer black. Then add an inner stroke that is white to make a

    border. You can see my settings below.

    Go to Layer>Flatten Imageto flatten the image. Hit CMD+Ato select all and then go

    Edit>Define Pattern.

  • 8/13/2019 belajar edit

    12/16

  • 8/13/2019 belajar edit

    13/16

    Step 10

    Go back to your other document. Make a new blank layer just above your curves layer by hitting

    the New Layer button at the bottom of the layer palette. Not go to Edit>Filland select Patternfor the Contents. Then select your black box that should be at the end of the list, and hit OK.

    Now Hit (CMD+T) to transformthe layer so that it fits in the foreground space. Then

    (right/control+click)anywhere in the transform box and select perspective. Drag the bottom

    right handleway out so you get a nice perspective on the pattern layer. Set the layers blending

    mode to screen and the opacity to 15%.

  • 8/13/2019 belajar edit

    14/16

  • 8/13/2019 belajar edit

    15/16

    Step 11

    There is one last step to add a finishing touch. Select the type layers and duplicate them by

    dragging them down to the New Layer button. With the new groups selected hit (CMD+T)then (right/control+click) in the transform box and select Flip Vertical. Move them down so

    they look like a reflection.

    With all the reflection groups selected hit (CMD+G)to put them into another group. Set that

    groups opacity to 25%. Add a mask to the group by clicking on the Add Layer Mask button

    at the bottom of the layer palette. With the mask selected hit (G) for the gradient tooland apply

    a linear gradient from black to white, so the reflection fades out as it goes down to the edge ofthe image.

    Conclusion

    This tutorial covered some simple steps and effects to achieve stylish results. The final image is

    below. If there are any questions, put them in the comments section. I will answer them as soon

    as I can. I hope you enjoy this tut!

  • 8/13/2019 belajar edit

    16/16