bes920xl ib c13 fa lowres

8/10/2019 Bes920xl Ib c13 Fa Lowres

1/48

Suits all BES920XL models

the Dual Boiler Instruction Book - Manuel dinstructions

www.breville.com

USAMail: Breville USA

19400 S. Western AveTorrance CA90501-1119

Phone: 1-866-273-84551-866-BREVILLE

Web: brevilleusasupport.com

CanadaMail: Breville Canada

2555, Avenue de lAviationPointe-Claire (Montreal)Quebec H9P 2Z2

Phone: 1-855-683-3535

Email: [email protected]

Breville Consumer Support

Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.Copyright Breville Pty. Ltd. 2013.

Due to continued product improvement, the products illustrated/photographedin this book may vary slightly from the actual product.

Model BES920XL Issue - C13


2/48

3

CONTENTS

4 Breville recommends safety rst

7 Know your Breville product

11 Operating your Breville product

27 Coffee making tips & preparation

32 Care & cleaning39 Troubleshooting

46 Coffees to try

CONGRATULATIONSOn the purchase of your Breville product

*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.

USA Consumers: www.brevilleusa.com

Canadian Consumers: www.breville.ca

Register online for product supportand exclusive offers.*


3/48

4 5

PAGE HEADER..... PAGE HEADER.....

BREVILLE RECOMMENDS SAFETY FIRSTBREVILLE RECOMMENDS SAFETY FIRST

5

At Breville we are very safety conscious. We design and manufacture consumer products withthe safety of you, our valued customer, foremost in mind. In addition we ask that you exercisea degree of care when using any electrical appliance and adhere to the following precautions.

When using e lectrical appliances, basicsafety precautions should always befollowed, including the following:

FOR ALL ELECTRICALAPPLIANCES

Carefully read all instructionsbefore operating and save forfuture reference.

Do not touch hot surfaces. Usehandles or knobs as advised in

this instruction book. To protect against re, electric

shock and injury to persons donot immerse the power cord,plug, or appliance itself in wateror other liquids.

Close supervision is necessarywhen any appliance is used byor near children.

If the appliance is to be:- left unattended- cleaned- moved- assembled; or- storedAlways switch off the applianceby pressing the POWER buttonto off and unplug from thepower outlet.

Always allow the appliance tocool before cleaning, movingor storing.

It is recommended to regularlyinspect the appliance and powercord. Do not use the applianceif there is damage to thepower cord or plug, or after theappliance malfunctions or hasbeen damaged in any way.Immediately stop use and call

Breville Consumer Support. The use of accessory

attachments not recommendedby Breville may result in re,electric shock or injury topersons.

Do not let the power cordhang over the edge of a tableor counter-top, or touch hotsurfaces.

Do not place the appliancenear the edge of a table orcounter-top. Ensure the surfaceis level, clean and free of waterand other substances.

Do not place the appliance onor near a hot gas or electricburner. Do not place it in, orallow it to come in contact witha heated oven.

IMPORTANT SAFEGUARDS

Do not attempt to open orservice the espresso machine.

For any maintenance other thancleaning, call Breville ConsumerSupport or visit a Breville

Authorized Servicer.SHORT CORD INSTRUCTIONSYour Breville appliance is ttedwith a short power cord to reducepersonal injury or property damageresulting from pulling, trippingor becoming entangled with alonger cord. Longer detachablepower cords or extension cords areavailable and may be used if careis exercised. If an extension cord isused, (1) the marked electrical ratingof the cord set or extension cordshould be at least as great as theelectrical rating of the appliance,(2) the cord should be arrangedso that it will not drape over thecounter-top or table where it canbe pulled on by children or trippedover unintentionally and (3) theextension cord must include a3-prong grounding plug.

This appliance is recommendedfor household use only. Do notuse this appliance for anythingother than its intended use. Donot use outdoors. Do not use inmoving vehicles or boats.

SPECIFIC INSTRUCTIONSFOR BES920XL

It is recommended to plug theespresso machine into a properlygrounded and dedicated circuit,separate from other electricalappliances.

Use only cold water in thewater tank. Do not use anyother liquids. Do not use highlyltered, demineralized ordistilled water as this may affectthe taste of the coffee and howthe espresso machine operates.

Ensure the portalter is rmlyinserted and secured into thegroup head before starting anextraction. Never remove theportalter during the extractionprocess.

Caution must be used duringdescaling as hot steam may bereleased. Before descaling, turnoff the machine, allow to coolfor at least 1 hour and ensurethe drip tray is empty and fullyinserted. For instructions, refer toDescale (dESc), page 35.


4/48

6

PAGE HEADER.....

BREVILLE RECOMMENDS SAFETY FIRST

BREVILLE ASSIST PLUGYour Breville appliance comes witha unique Assist Plug, convenientlydesigned with a nger hole to easeremoval from the power outlet.

CSA DUTY CYCLE MARKING:The Canadian Standards Authorityrequires any appliances capable ofdrawing over 1500W to be markedwith a duty cycle in minutes. Forthe BES920XL, this duty cyclerepresents the maximum time forwhich the appliance will draw over1500W during any 2 hour periodof use. It does not indicate theappliance is unsafe for continuoususe or is required to be switchedoff at certain intervals duringnormal use.

CALIFORNIA PROPOSITION 65:(Applicable to Californiaresidents only).This product contains chemicalsknown to the State of California tocause cancer, birth defects or otherreproductive harm.

SAVE THESE INSTRUCTIONS

KNOWyour Breville product


5/48

8 9

PAGE HEADER..... PAGE HEADER.....FEATURES OF YOUR BREVILLE PRODUCT

TRIPLE HEAT SYSTEM

Dual Stainless Steel BoilersDedicated espresso and steam boilers forsimultaneous milk texturing and espressoextraction at the optimum temperature.

Actively Heated Group HeadCommercial 58mm group head withembedded element for optimal thermalstability during extraction.

PRECISION CONTROL

Electronic PID Temperature ControlElectronic temperature control deliversprecise water temperature for optimumespresso avor. Programmable.

Regulated Extraction PressureOver pressure valve (OPV) limits maximumpressure for optimal espresso avor.

Low Pressure Pre-InfusionGradually increases water pressure to gentlyexpand grinds for an even extraction.Programmable.

Dual PumpsDedicated espresso and steam boilerpumps help maintain constant pressurethroughout extraction.

Programmable Shot TemperatureAdjust water temperature to achieve optimalespresso avor depending on coffee originand degree of roast.

ADDITIONAL FEATURES

Backlit LCDDisplays current settings and simpliesprogramming functions.

High Volume Instant SteamDedicated 32 .oz (950ml) steam boilerdelivers instant and continuous steam.

Commercial Steam WandStainless steel 360 swivel-action steamwand with 3 hole tip for a silkier texture.

Instant Hot WaterDedicated hot water outlet for makingAmericanos and pre-heating cups.

58mm Full Stainless Steel PortalterHelps to promote a more even extractionand is easier to clean.

Shot ClockDisplays duration of the espresso shotbeing extracted.

Auto StartSwitches machine on at a specied time.

The Razor Dose Trimming ToolPatented twist blade trims down the puckto the right level for precision dosing anda consistent extraction.

KNOW YOUR BREVILLE PRODUCT

A. Top-ll 84 .oz (2.5L) removablewater tankWith integrated water lter and backlitlevel indicator.

B. Hot water dialRotate to start and stop the ow of hotwater from the hot water outlet.

C. POWER buttonD. Backlit LCD

Displays current settings and simpliesprogramming functions.E. MENU button

Use in conjunction with the LCD to setthe programmable functions.

F. Espresso pressure gaugeMonitors extraction pressure.

G. Integrated & removable 58mm tamperH. Heated 58mm group head with

embedded elementI. 58mm full stainless steel portalter

J. Heated cup warming trayK. 1 CUP, 2 CUP and MANUAL buttons

With preset shot durations, manualoverride or reprogrammabledurations/volumes.

L. Steam leverFor instant and continuous steam.

M. Dedicated hot water outletDelivers hot water for Americanos andpre-heating cups.

N. 360 swivel action steam wandWith 3 hole tip for a silkier texture.

O. Descale access pointP. Tool storage tray

Houses accessories when not in use.Q. Drop down swivel foot

Lifts the machine upwards for easymaneuverability.

R. Removable drip trayWith Empty Me! indicator.

HI

FG

D

E

C

AB

J

K

L

M

NOP

RQA


6/48

10

PAGE HEADER.....KNOW YOUR BREVILLE PRODUCT

I

H

A

DC

G

J

E

F

B

ACCESSORIESA. Stainless steel milk jugB. Water filter holder with lterC. 1 CUP & 2 CUP single wall lter basketsD. 1 CUP & 2 CUP dual wall lter basketsE. Cleaning discF. The Razor precision dose trimming toolG. Water hardness test strip

H. Espresso cleaning tabletsI. Cleaning tool for steam wand tipJ. Allen key

OPERATINGyour Breville product


7/4812 13

PAGE HEADER..... PAGE HEADER.....OPERATING YOUR BREVILLE PRODUCT

BEFORE FIRST USE

Machine PreparationRemove and discard all labels andpackaging materials attached to yourespresso machine. Ensure you haveremoved all parts and accessories before

discarding the packaging.Remove the water tank located at theback of the machine by pulling down thewater tank handle. Remove the plastic bagcontaining the water lter and water lterholder. Clean parts and accessories (watertank, portalter, lter baskets, jug) usingwarm water and a gentle dish washingliquid. Rinse well then dry thoroughly.

TIPTo easily maneuver your machine, use thedrop down swivel foot located under thedrip tray. When turned to UNLOCK, theswivel foot drops down & lifts the machineupwards, making it easier to access theremovable water tank or reposition themachine to another location.

INSTALLING THE WATER FILTER Remove the water lter and water lter

holder from the plastic bag. Soak the lter in a cup of water for

5 minutes then rinse under coldrunning water.

Wash the lter holder with cold water,taking specic care to rinse thestainless steel mesh.

Soak fil ter for 5 minutes Rinse fi lter & mesh

Insert the lter into the two parts of thelter holder.

Place filter intofilter holder

To install the assembled filter holderinto the water tank, align the base of thelter holder with the adapter inside thewater tank. Push down to lock into place.

Fill the water tank with cold water beforesliding back into position at the back ofthe machine and locking into place.

NOTE

DO NOT use highly ltered,demineralized or distilled water in thismachine. This may affect the taste of thecoffee and how the machine operates.

NOTETo purchase water lters, visitwww.breville.com or call BrevilleConsumer Support.

OPERATING YOUR BREVILLE PRODUCT

FIRST USE1. Ensure tank is lled with cold water.

You can do this by either openingthe top-ll water tank lid (push toopen), or by removing the water tankat the back of the machine.

2. Check STEAM LEVER and HOTWATER dial are in the CLOSEDposition.

3. Press POWER button to turnmachine on.

4. The LCD will display Hrd3,prompting you to set the waterhardness level. Programming thiswill determine the regularity of theNEW FILTER alert which indicateswhen the water lter in the watertank needs to be replaced.

Setting Water Hardness Remove the supplied water hardness teststrip from the wrapper.

Dip the test strip into a sample of thewater you have lled the tank with. Waitfor one minute. The water hardnesssetting is indicated by the number ofred squares displayed on the test stripeg. 3 red squares indicates a waterhardness setting of 3.

Press UP or DOWN arrow to therequired setting from Hrd1 (softestwater) to Hrd5 (hardest water). PressMENU button to set. Machine will beepto conrm selection.

NOTEIf there is no selection within 5 minutes,the machine will default to settingHrd3.

5. A pumping/vibrating sound will beheard indicating empty boilers arebeing lled with water for the rsttime. The LCD will display the currentboiler temperature as it heats up.

6. After approximately 10 minutes,the machine will reach thedefault operating temperature(200F/93C) and all 4 buttons willilluminate. The machine is now inSTANDBY mode, ready for the nextstep, Flushing The Machine.

POWER

NOTEYou will not be able to select the 1 CUPor 2 CUP functions; access the cleaningcycle in the menu options; or activate thesteam wand until the machine has reachedoperating temperature (STANDBY mode).The machine will beep 3 times if one ofthese functions is selected.


8/4814 15

PAGE HEADER.....OPERATING YOUR BREVILLE PRODUCT

Flushing The MachineWhen the machine has reachedSTANDBY mode:1. Press 2 CUP button to run

water through the group head for30 seconds.

2. Rotate HOT WATER dial tothe OPEN position to run waterthrough the hot water outlet. After30 seconds, rotate HOT WATER dialto the CLOSED position.

3. Lift STEAM LEVER to the OPENposition to release steam throughthe steam wand. After 30 seconds,lower the STEAM LEVER to theCLOSED position.

4. Repeat steps 13 twice.5. Re-ll water tank and empty drip

tray, if required.

POWER SAVE MODEThe machine will enter POWER SAVE modeafter remaining idle for 1 hour and turn offcompletely if not used for a continuous4 hour period.Pressing any button during POWERSAVE (except POWER), or operating theSTEAM LEVER or HOT WATER dial willcause the machine to heat-up to operatingtemperature.Pressing the POWER button duringPOWER SAVE will turn the machine off.

LCD INTERFACE

Display modes3 modes can be displayed on theLCD screen: Shot Temperature, Shot Clockor Clock.Press UP or DOWN arrow to change thedisplay mode.1. Shot TempDisplays selected extraction temperature.The default is 200F (93C), but can bechanged from 190F205F (86C96C).See Extraction Temperature, page 19.

2. Shot ClockDisplays duration of espresso extraction inseconds. See Extraction Guide, page 31.

Shot clock will be displayed during anextraction and 10 seconds after theextraction before returning to the defaultshot temperature display mode.


3. ClockDisplays current time. The default is12:00AM if the time has not been set.See Set Clock, page 19.

If selected, the clock will display for10 seconds before returning to the defaultshot temperature display mode.

GENERAL OPERATIONThe 1 CUP & 2 CUP buttons use duration tocontrol espresso volume. The duration timesare preset, but can be reprogrammed (referto Reprogramming Shot Duration, page 18).Alternatively, access the Advanced Featuresif you wish to use volumetric controlsinstead of duration to determine espressovolume (refer to Volumetric Control (vOL),page 23).

1 CUP BUTTONPress 1 CUP button once to extract a singleshot of espresso at the preset duration(30 seconds). The extraction will startusing the low pressure pre-infusion.

The machine will stop after 30 seconds andreturn to STANDBY mode.

TIPTo by-pass low pressure pre-infusionand deliver water to the group head atfull pump pressure, press and hold the1 CUP button. Release button whenthe desired amount of espresso hasbeen extracted. This function can beused when purging the group head.

2 CUP BUTTONPress 2 CUP button once to extract adouble shot of espresso at the presetduration (30 seconds). The extraction willstart using the low pressure pre-infusion.

The machine will stop after 30 seconds andreturn to STANDBY mode.

TIPTo by-pass low pressure pre-infusionand deliver water to the group head atfull pump pressure, press and hold the2 CUP button. Release button whenthe desired amount of espresso hasbeen extracted. This function can beused when purging the group head.


9/4816 17


MANUAL BUTTONThe MANUAL button allows you to controlthe espresso duration/volume to suit yourpreference. Press MANUAL button once tostart the espresso extraction.The extraction will start using the lowpressure pre-infusion. Press MANUAL

button again to stop extraction.

TIPTo manually control the low pressurepre-infusion duration, press andhold the MANUAL button. When therequired pre-infusion duration is met,release button to begin full pumppressure. Press MANUAL buttonagain to stop extraction.

STEAMFor instant steam, move STEAM LEVERto OPEN position. The STEAM LED willilluminate.

To turn steam off, move STEAM LEVER toCLOSED position. The machine will returnto STANDBY mode.

CAUTION: BURN HAZARDPressurized steam can still be released,

even after machine has been switched off.Children must always be supervised.


HOT WATERFor instant hot water, rotate the HOTWATER dial to OPEN position. The HOTWATER LED will illuminate.

To turn hot water off, rotate theHOT WATER dial to CLOSED position.The machine will return to STANDBY mode.

NOTEYou cannot run hot water and extract

espresso at the same time.

NOTEHot water will cease to dispense afterapprox. 30 seconds. Depending onthe size of your cup, you may need toclose, then re-open the HOT WATERdial. See HOT WATER LED ashing,page 23.

PROGRAMMABLE FUNCTIONSTo enter program mode, press the MENUbutton. Continue to press MENU buttonuntil the desired function is ashing onthe LCD.Program mode allows you to program:

Shot Volume Shot Temperature Auto Start Clean Cycle Set Clock

To exit program mode, press EXIT button.

NOTEThe MENU button is disabled duringan extraction or when dispensinghot water.


10/4818 19


REPROGRAMMING SHOTDURATIONThe 1 CUP and 2 CUP buttons use durationto control espresso volume. Reprogramthe preset 30 second duration to yourpreference.Press MENU button until SHOT VOLashes and either 1 CUP or 2 CUP isdisplayed, depending on the button youdlike to reprogram.Without the portalter in place, press thebutton youd like to reprogram (either 1 CUPor 2 CUP button) to start water ow fromthe group head. Using the shot clock on theLCD, press the 1 CUP or 2 CUP button oncethe required duration has been reached.

Reprogramming 1 CUP button

Reprogramming 2 CUP button

The machine will beep. Press the EXITbutton to set the new duration.

REPROGRAMMING SHOTVOLUMEThe 1 CUP and 2 CUP buttons use durationto control espresso volume. Access theAdvanced Features if you wish to usevolumetric controls instead of durationto determine espresso volume (refer toVolumetric Control (vOL), page 23). Thenfollow these instructions:Press MENU button until SHOT VOLashes and either 1 CUP or 2 CUP isdisplayed, depending on the button youdlike to reprogram.Dose & tamp the portalter with groundcoffee. Insert the portalter into thegroup head. Press the button youd like toreprogram (either 1 CUP or 2 CUP button)to start espresso extraction. Press the 1 CUPor 2 CUP button once the desired volume ofespresso has been extracted. The machinewill beep. Press the EXIT button to set thenew volume.


EXTRACTION TEMPERATUREPress MENU button until SHOT TEMPashes. The LCD will display the currentshot temperature.

Press UP or DOWN arrow to adjustthe temperature. The default is set at200F (93C) but can be changed from190F 205F (86C 96C).

The optimum temperature will depend

on the origin of the coffee beans, theirfreshness and degree of roast.We recommend a temperature rangebetween 194F 203F (90C 95C)for optimal avor.The new temperature will be displayedon the LCD. Press the EXIT button to set.

SET CLOCKSetting the clock is optional. Press MENUbutton until SET CLOCK ashes. Thedefault is 12.00AM if time has not been set.

Press UP or DOWN arrow to adjust the time.For faster scrolling, press and hold the UP orDOWN arrow. Press the EXIT button to set.


11/4820 21


AUTO STARTAuto Start is optional. It allows you toprogram the specic time when the machinewill automatically turn on. By programmingyour machine, you will not have to wait forit to pre-heat. We recommend programmingthe machine to start 15 minutes before youplan to use it.Press MENU button until AUTO STARTashes and the current Auto Start setting(ON or OFF) is displayed on the LCD.

Press UP or DOWN arrow to set theAUTO START to ON or OFF.

If OFF is selected, press the EXIT buttonto set.

If ON is selected, press the MENU button.Press UP or DOWN arrow to the desiredAuto Start time. For faster scrolling, pressand hold the UP or DOWN arrow.

Press the EXIT button to set. A small clockicon will be displayed on the LCD when theAuto Start function has been programmed.

CLEANING CYCLEThe cleaning cycle cleans the shower screenand back-ushes the group head.Select this feature when the LCD displaysCLEAN ME! Refer to Cleaning Cycle,page 33.


ADVANCED FEATURESThese features should only be accessed byexperienced users.To access Advanced Features, with themachine turned off, press and hold the1 CUP button, then also press the POWER

button. Press the UP arrow to the desiredfeature then press MENU button to accessfeature settings.Press the EXIT button at any time to exit.

POWER

POWER

TURNPOWER OFF

THEN PRESS& HOLD

Reset Default Settings (rSEt)Use this function to reset all programmablevalues back to the default settings. Themachine has the following default settings:1. Temperature 200F (93C)2. Pre-Infusion Duration Pd073. Pre-Infusion Power PP60

4. Steam temperature 275F (135C)5. Machine Audio LO6. Auto Off ON7. Auto Start OFF8. Temperature Unit Fahrenheit9. Water Hardness Hrd310. Shot Duration 30 secs

While rSET is displayed on the LCD, pressthe MENU button to reset all settings tofactory defaults. Machine will beep toconrm selection.

Hrd3 will ash on screen. Machine is nowin Water Hardness mode. Determine waterhardness with the supplied water hardnesstest strip. Refer to Setting Water Hardness,page 13. Press UP or DOWN arrow to therequired setting from Hrd1 (softest water)to Hrd5 (hardest water). Press MENUbutton to set. Machine will beep to conrm

selection.Setting water hardness will determine theregularity of the NEW FILTER alert whichindicates when the water lter in the watertank needs to be replaced.

Descale (dESc)Select this feature to access the step by stepdescale procedure on the LCD. Refer topage 35 for the accompanying instructions.


12/4822 23


Temperature Unit - C/F (SEt)

Set units to metric or imperial. While SEt isdisplayed on the LCD, press MENU button.Press UP or DOWN arrow to the desiredunit. Press MENU button to set. Machinewill beep to conrm selection.

Steam Temperature (StEA)

Adjust the steam boiler temperature,which in turn controls steam pressure.Lower steam temperature to texture smallervolumes of milk or to have more control.Increase steam temperature to texture largervolumes of milk.While StEA is displayed on the LCD, pressMENU button. Press UP or DOWN arrow

to the desired temperature. Press MENUbutton to set. Machine will beep toconrm selection.

Disable AUTO OFF (A OF)

Use this function to disable the Auto Offfeature. While A OF is displayed on theLCD, press MENU button. Press UP orDOWN arrow to select off or on. PressMENU button to set. Machine will beepto conrm selection.

Machine Audio (Snd)

Adjust the audible alerts. While Snd isdisplayed on the LCD, press MENU button.Press UP or DOWN arrow to off (OFF), low(LO) or high (HI). Press MENU button toset. Depending on the selected setting, themachine may beep to conrm selection.


Volumetric Control (vOL)

Select between volume based (FLo) ortime based (SEc) method for espresso dosemeasurement. While vOL is displayed onthe LCD, press MENU button. Press UP orDOWN arrow to the desired method. PressMENU button to set. Machine will beep toconrm selection.

PRE-INFUSION PROGRAMMINGWith the machine on and in STANDBYmode, press UP and DOWN arrow togetherto enter Pre-Infusion Programming mode.Press MENU button to move betweenPre-Infusion Duration (Pd) and Pre-InfusionPower (PP).

Pre-Infusion Duration (Pd)The LCD will display the currentPre-Infusion Duration.Press UP or DOWN arrow to vary time.

We recommend a range between 515 secsas being optimum. Press MENU button toaccess Pre-Infusion Power, or press EXITbutton to set.

Pre-Infusion Power (PP)The LCD will display currentPre-Infusion Power.Press UP or DOWN arrow to vary power.

We recommend a range between 5065 asbeing optimum. Press EXIT button to set.

ALERTS

STEAM LEVER beeps during heat-upThe machine will beep 3 times and notreach operating temperature (STANDBYmode) if the STEAM LEVER is in the OPENposition. Move the STEAM LEVER to theCLOSED position.

HOT WATER LED ashing during heat-upThe machine will not reach operatingtemperature (STANDBY mode) if the HOTWATER dial is in the OPEN position. TheHOT WATER LED will ash. Move the HOTWATER dial to the CLOSED position.

HOT WATER LED ashingTo ensure water is dispensed at the correcttemperature, hot water will cease todispense after approx. 30 seconds and theHOT WATER LED will ash. Move theHOT WATER dial to the CLOSED position.


13/48

24 25


Fill TankThe machine will detect a low water level.The LCD will display FILL TANK.

Fill tank with cold fresh water. The machinewill not be able to make coffee or hot waterwhile the tank is empty.

Clean Me!Indicates when 200 extractions have beencarried out since the last cleaning cycle.The cleaning cycle cleans the showerscreen and back-ushes the group head. Forinformation on how to clean the machine,refer to Cleaning Cycle, page 33.

New FilterIndicates when the water lter in the watertank needs to be replaced. For informationon changing the lter, refer to InstallingWater Filters, page 33.The regularity of this alert is determinedby the water hardness setting (Hrd1-Hrd5)

selected. For information, refer to SettingWater Hardness, page 13.

Temperature ashingIndicates when the machine is heating upor if the temperature drops excessivelyduring use.

ServiceTo ensure a long life of optimal brewingand steaming performance, it is importantthe machine is serviced by Breville or anAuthorized Servicer when the SERVICEprompt scrolls across the LCD screen.The SERVICE prompt will appear after6,000 cycles - approximately 4 - 5 years ofregular use in a domestic environment.The frequency of this prompt will dependon your frequency of use.

Contact Breville Consumer Supportfor advice.

TRANSPORTING AND STORINGWe recommend draining both boilerscompletely before transporting the machineor storing for an extended period of time.This procedure is also intended as ananti-freeze measure in the event the machineis exposed to extreme cold temperatures.

CAUTION Never open DESCALE ACCESS valveswhile machine is still hot. Alwaysturn off the machine and allow to coolfor at least 1 hour prior to startingdescale process.

CAUTION During descale process, water mayow through group head and the driptray will ll with water.

Step 1 Preparationa) Ensure the machine is off and has cooled

for at least 1 hour.b) Empty water tank, remove water lter

then replace and lock water tank backinto position.

c) Ensure drip tray is empty and fullyinserted into position.


Step 2 Empty Boilersa) Remove the grey silicone cover on the

lower front panel marked DESCALEACCESS. Place a cloth over thedrip tray to stop steam escaping.

REMOVE

b) Use a at-head screwdriver to rotate theright screw counter-clockwise until thevalve is fully open. As the valve opens,steam may be released.

CAUTION HOT WATER & STEAM


14/48

26


c) Next, repeat the process on the leftscrew. As the valve is opened, water maybegin owing into the drip tray.

d) Allow valves to remain open until nomore water or steam escapes.

e) Close both valves by rotating screwsclock-wise until seated. Do not

overtighten screws to avoid damagingthe valves. Replace the grey siliconecover over the valves.

f) Empty drip tray and reinsert into

position. Use caution as the drip traymay be hot due to the water and steamfrom the boilers.

COFFEE MAKING TIPS& PREPARATION


15/48

28 29

PAGE HEADER.....COFFEE MAKING TIPS & PREPARATION

PRE-HEATING

Heating your cup or glassA warm cup will help maintain the coffeesoptimal temperature. Pre-heat your cup byrinsing with hot water from the hot wateroutlet and place on the cup warming tray.

Heating the portalter and lter basketA cold portalter and lter basket canreduce the extraction temperature enoughto signicantly affect the quality of yourespresso. Always ensure the portalter andlter basket are pre-heated with hot waterfrom the hot water outlet before initial use.

NOTEAlways wipe the portalter and lterbasket dry before dosing with groundcoffee as moisture can encouragechanneling where water by-passes theground coffee during extraction.

SELECTING FILTER BASKET

Single Wall Filter BasketsUse Single Wall lter baskets if grindingfresh whole coffee beans.Single Wall lter baskets allow you toexperiment with grind and dose to create amore balanced espresso.

1 CUP 2 CUP

Dual Wall Filter BasketsUse Dual Wall lter baskets if usingpre-ground coffee.Dual Wall lter baskets regulate thepressure and help to optimize theextraction regardless of the grind, dose orfreshness.

1 CUP 2 CUP

NOTERegardless of whether you use SingleWall or Dual Wall lter baskets, usethe 1 CUP basket when brewing a

single cup and the 2 CUP basket whenbrewing two cups or a stronger singlecup or mug.

THE GRINDIf grinding coffee beans, the grind sizeshould be ne but not too ne. The grindsize will affect the rate at which the waterows through the ground coffee in the lterbasket and the taste of the espresso.If the grind is too ne (looks like powderand feels like our when rubbed betweenngers), the water will not ow throughthe coffee even when under pressure.The resulting espresso will be OVER-EXTRACTED, dark in color and bitterin avor.If the grind is too coarse the water willow through the ground coffee in the lterbasket too quickly. The resulting espressowill be UNDER-EXTRACTED and lackingin color and avor.

COFFEE MAKING TIPS & PREPARATION

DOSE AND TAMPING Wipe lter basket with a dry cloth. If using Single Wall lter baskets, grind

just enough coffee to ll the lter basket.You may need to experiment with howlong the grinder needs to run to achievethe correct dose.

Tap the portalter several times todistribute the coffee evenly in thelter basket.

Tamp down rmly (using approx.30-40lbs or 15-20kg of pressure). Theamount of pressure is not as importantas consistent pressure every time.

As a guide to dose, the top edge of themetal cap on the tamper should be levelwith the top of the lter basket after thecoffee has been tamped.

TRIMMING THE DOSEThe Razor precision dose trimming toolallows you to trim the puck to the right levelfor a consistent extraction.

the Razor Precisiondose trimmingtool

Insert the Razor dose trimming toolinto the lter basket until the shouldersof the tool rest on the rim of the basket.The blade of the dose trimming toolshould penetrate the surface of thetamped coffee.

Rotate the Razor dose trimmingtool back and forth while holding theportalter on an angle over a knockbox to trim off excess coffee grinds.Your lter basket is now dosed with thecorrect amount of coffee.

Wipe excess coffee from the rim of the

lter basket to ensure a proper seal isachieved in the group head.

TIPIf the extraction is too fast, make thegrind ner & repeat above steps. If theextraction is too slow, make the grindcoarser and repeat above steps.

PURGING THE GROUP HEADBefore placing the portalter into the grouphead, run a short ow of water through thegroup head by pressing and holding the1 CUP button. Allow water to ow for5 seconds, then release the 1 CUP button to

stop the ow of water. This will purge anyground coffee residue from the group headand stabilize the temperature priorto extraction.


16/48

30 31

PAGE HEADER.....COFFEE MAKING TIPS & PREPARATION

INSERTING THE PORTAFILTERPlace the portalter underneath the grouphead so the handle is aligned with theINSERT position. Insert the portalterinto the group head and rotate to the rightuntil the handle is securely locked in place.Rotating past the center will not damage the

silicone seal.

EXTRACTING ESPRESSO Place pre-warmed cup(s) beneath the

portalter and press the MANUAL,1 CUP or 2 CUP button.

As a guide, the espresso will startto ow after 914 seconds (this includespre-infusion time) and should be theconsistency of dripping honey.

If the espresso starts to ow before9 seconds you have either underdosed the lter basket and/or the

grind is too coarse. This is anUNDER-EXTRACTED shot. If the espresso starts to drip or ow

after 14 seconds, then you haveeither over dosed the lter basketand/or the grind is too ne. This isan OVER-EXTRACTED shot.

A great espresso is about achieving theperfect balance between sweetness, acidityand bitterness.The avor of your coffee will depend onmany factors, such as the type of coffeebeans, degree of roast, freshness, coarsenessor neness of the grind, dose of groundcoffee, and tamping pressure.Experiment by adjusting these factors just one at a time to achieve the tasteof your preference.

TEXTURING MILK Always start with fresh cold milk. Fill the jug just below the V at the

bottom of the spout. Position the steam tip above the drip tray

and lift the STEAM LEVER to purge thesteam wand of any condensed water.

Insert the steam tip -" (1-2cm)below the surface of the milk, close tothe right hand side of the jug at the3 oclock position.

Move the STEAM LEVER to the OPENposition.

Keep the tip just under the surface of themilk until the milk is spinning clockwise,producing a vortex (whirlpool effect).

With the milk spinning, slowly lower the jug. This will bring the steam tip to thesurface of the milk & start to introduceair into the milk. You may have to gently

break the surface of the milk with the tipto get the milk spinning fast enough. Keep the tip at or slightly below the

surface, continuing to maintain thevortex. Texture the milk until sufcientvolume is obtained.

Lift the handle of the jug to lower thetip beneath the surface, but keep thevortex of milk spinning. The milk is atthe correct temperature (140150F or6065C) when the jug is hot to touch.

Move the STEAM LEVER to theCLOSED position BEFORE taking thetip out of the milk.

Set the jug to one side. Wipe the wand &tip with a damp cloth. Position the steamtip above the drip tray and lift the steamlever to purge out any residual milk.

Tap the jug on the bench to collapseany bubbles.

Swirl the jug to polish and re-integratethe texture.

Pour milk directly into the espresso. The key is to work quickly, before the

milk begins to separate.

OPTIMUM OPTIMUM 25-35 SECBALANCED

TOO FINE TOO MUCHUSE RAZOR TO TRIM

TOO LITTLEINCREASE DOSE &

USE RAZOR TO TRIM

OVER 40 SECOVER EXTRACTED

TOO COARSE UNDER 20 SECUNDER EXTRACTED

30-40lbs(15-20kg)

TOO HEAVY

TOO LIGHT

EXTRACTION GUIDE

HINTS & TIPS Fresh, quality coffee beans will give

you the best possible extraction. We recommend quality 100% Arabica

beans with a Roasted On date stampedon the bag, not a Best Before or UseBy date.

Coffee beans are best consumedbetween 520 days after theRoasted On date. Ideally onlygrind directly before the extractionto maximize avor.

Buy coffee beans in small batches toreduce the storage time.

Store coffee beans in a cool, dark anddry container. Vacuum seal if possible.

COFFEE MAKING TIPS & PREPARATION


17/48

32 33

CARE & CLEANINGCARE & CLEANING

CLEANING CYCLE CLEAN ME! will be displayed on the

LCD to indicate when a cleaning cycleis required (approx. 200 shots).

Insert the 1 CUP lter basket intothe portalter, followed by thesupplied cleaning disc, followed by1 cleaning tablet.

Lock the portalter into the group head,ensuring it is rotated to the right untilthe handle is securely locked in place.

Ensure the water tank is lled withcold water and empty the drip tray.

Press MENU button untilCLEAN CYCLE ashes and PUSHis displayed on the LCD.

To start the cleaning cycle press theilluminated MANUAL button.

CLEAN CYCLE will ash and themachine will start to countdown from370 seconds.

When the cleaning cycle has nished,remove the portalter and ensurethe tablet has completely dissolved.If the tablet has not dissolved, repeatthe steps above, without inserting anew tablet.

The cleaning cycle is now complete.Rinse the portalter and lter basketthoroughly to remove any tablet residuebefore using.

INSTALLING WATER FILTERS Discard the used water lter. Soak a new

lter in a cup of water for 5 minutes,then rinse under cold running water.

Wash the water lter holder with coldwater, taking specic care to rinse thestainless steel mesh.

Insert the new water lter into the twoparts of the water lter holder.

To install the assembled water lterholder into the water tank, align the baseof the water lter holder with the adapterinside the water tank. Push down to lockinto place.

Slide the water tank back into positionat the back of the machine and lockinto place.

NOTETo purchase additional water lters,visit www.breville.com or callBreville Consumer Support.


18/48

34 35

CARE & CLEANING

CLEANING THE STEAM WAND Immediately after texturing milk, wipe

the steam wand with a damp cloth andpurge by lifting the STEAM LEVER for afew seconds.

If any of the holes in the tip of thesteam wand become blocked, ensurethe STEAM LEVER is in the CLOSEDposition and clean using the pin on theend of the provided cleaning tool.

If steam wand remains blocked, removethe tip using the integrated spanner inthe cleaning tool and soak in hot water.Screw tip back onto the steam wandusing the integrated spanner in thecleaning tool.

CLEANING THE FILTER BASKETSAND PORTAFILTER The lter baskets and portalter should

be rinsed under hot water directly afteruse to remove all residual coffee oils. If the holes in the lter baskets become

blocked, dissolve a cleaning tablet inhot water and soak lter basket andportalter in solution for approx. 20minutes. Rinse thoroughly.

CLEANING THE SHOWER SCREEN The group head interior and shower

screen should be wiped with a damp clothto remove any ground coffee particles.

Periodically purge the machine with

hot water to rinse out any residualcoffee. Place an empty lter basket intothe portalter. To by-pass low pressurepre-infusion and deliver water to thegroup head at full pump pressure, pressand hold the 2 CUP button. Releasebutton after 20 seconds.

CLEAR WATER BACKFLUSHAfter each coffee making session werecommend doing a clear water backushbefore you turn off the machine. Insert thecleaning disc into the lter basket theninsert the portalter into the group head.Press the 2 CUP button and allow pressure

to build for 20secs, then press to stop &release pressure. Repeat this 5 times topurge any ne coffee grounds and residualcoffee oils from the brew water paths.

CLEANING THE DRIP TRAY& STORAGE TRAY The drip tray should be removed,

emptied and cleaned after each use orwhen the drip tray indicator is showingEmpty Me! Remove grill from the driptray. Wash both in warm soapy water.The Empty Me! indicator can also beremoved from the drip tray.

The storage tray can be removed andcleaned with a soft, damp cloth (do notuse abrasive cleansers, pads or clothswhich can scratch the surface).

CLEANING THE OUTER HOUSING& CUP WARMING TRAYThe outer housing and cup warming traycan be cleaned with a soft, damp cloth.Polish with a soft, dry cloth. Do not useabrasive cleansers, pads or cloths which canscratch the surface.

NOTEDo not clean any of the parts oraccessories in the dishwasher.

CARE & CLEANING

DESCALE (dESc)Use this function to access the step by stepdescale procedure on the LCD.

CAUTION Never open DESCALE ACCESS valves

while machine is still hot. Alwaysturn off the machine and allow to coolfor at least 1 hour prior to startingdescale process.

CAUTION During descale process, water mayow through group head and the driptray will ll with water.

Step 1 Prepare for Descalea) Ensure drip tray is empty and fully

inserted into position.b) Ensure the machine is off and has cooled

for at least 1 hour. With the machine off,press and hold the 1 CUP button, thenalso press the POWER button to accessAdvanced Features.

c) Press UP arrow until dESc is displayedon the LCD. Press MENU button toselect. The LCD will display PUSH andthe MANUAL button will illuminate.

Step 2 Empty Boilersa) Remove the grey silicone cover on the

lower front panel marked DESCALEACCESS. Place a cloth over the drip trayto stop steam escaping.

REMOVE

b) Use a at-head screwdriver to rotate theright screw counter-clockwise until the

valve is fully open. As the valve opens,steam may be released.


c) Next, repeat the process on the leftscrew. As the valve is opened, water maybegin owing into the drip tray.

d) Allow valves to remain open until nomore water or steam escapes.


19/48

36 37

e) Close both valves by rotating screwsclock-wise until seated. Do notovertighten screws to avoid damagingthe valves.

f) Empty drip tray and reinsert intoposition. Use caution as the drip traymay be hot due to the water and steamfrom the boilers.

g) Empty water tank, remove water lter.h) Empty descale solution into water tank,

then top with cold water to MAX line,or as per manufacturers instructions.Replace and lock water tank back intoposition at the back of the machine.

i) Press MANUAL button to proceed tothe next step.

NOTEIf boilers are not empty, the machinewill beep 3 times and vALv will bedisplayed on the LCD.

Step 3 Begin Descalea) 20 minute timer will begin. Machine

will ll boilers with descale solution andheat to temperature. During this time,water may ow through the group head.Wait for countdown timer to nish.This allows solution to dissolve scale

build up.

b) The LCD will display PUSH when thetimer has nished.

Step 4 Empty Descale Solutiona) Empty water tank then rinse and ll

with clean water to the MAX line.

Replace and lock water tank back intoposition at the back of the machine.

NOTEIf water tank has not been removedthen replaced or is empty, water tankLED will ash 5 times, the machinewill beep 3 times and FILL TANK willbe displayed on the LCD.

b) Place a cloth over the drip tray to stopsteam escaping.

c) Use a at-head screwdriver to rotate the

right screw counter-clockwise until thevalve is fully open. As the valve opens,steam may be released.


CARE & CLEANING

d) Next, repeat the process on the leftscrew. As the valve is opened, water maybegin owing into the drip tray.

e) Allow valves to remain open until nomore water or steam escapes.

f) Close both valves by rotating screwsclock-wise until seated. Do not

overtighten screws to avoid damagingthe valves.g) Empty drip tray and reinsert into

position. Use caution as the drip traymay be hot due to the water and steamfrom the boilers.

h) Press MANUAL button to proceed tonext step.

Step 5 Fill Boilersa) 5 minute timer will begin. During this

time, water may ow through the grouphead. Wait for countdown timer to nish.This allows any remaining solution to be

removed from the system.

b) The LCD will display PUSH when thetimer has nished.

Step 6 Flush Boilersa) Empty and rinse water tank. Assemble

new water lter into tank.b) Fill water tank with cold water to MAX

line. Replace and lock water tank backinto position at the back of the machine.

c) Ensure drip tray is empty and fully

inserted into position.d) Place a cloth over the drip tray to stop

steam escaping.e) Use a at-head screwdriver to rotate the

right screw counter-clockwise until thevalve is fully open. As the valve opens,steam may be released.


f) Next, repeat the process on the leftscrew. As the valve is opened, water maybegin owing into the drip tray.

g) Allow valves to remain open until nomore water or steam escapes.

h) Close both valves by rotating screwsclock-wise until seated. Do notovertighten screws to avoid damagingthe valves. Replace the grey siliconecover over the valves.

i) Empty drip tray and reinsert intoposition. Use caution as the drip traymay be hot due to the water and steamfrom the boilers.

j) Press MANUAL button to completedescale procedure. Machine will heat

up and is ready to use once operatingtemperature (STANDBY mode)is reached.

CARE & CLEANING


20/48

38

CARE & CLEANING

USING THE ALLEN KEYOver time, the silicone seal surrounding theshower screen will need to be replaced toensure optimum brewing performance.1. Press the POWER button to turn the

machine off and unplug the cord fromthe power outlet.

2. Carefully remove the rear water tankand drip tray, taking particular care ifthey are full.

3. Using a skewer or similar, cleanthe center of the screw of any residualcoffee.

4. Insert the shorter end of the AllenKey into the center of the screw. Turncounter-clockwise to loosen the screw.

Clean center of screw

before inserting Allen Key

5. Once loosened, carefully remove andretain the screw, stainless steel showerscreen and black dispersion plate. Makenote of the side of the shower screen

and dispersion plate that are facingdownwards. This will make re-assemblyeasier. Wash the shower screen anddispersion plate in warm soapy water,then dry thoroughly.

6. Remove the silicone seal with yourngers or a pair of long-nose pliers.Insert the new seal, at side rst, sothe ribbed side is facing you.

7. Re-insert the dispersion plate, then theshower screen, then the screw. Withyour ngers, turn the screw clockwisefor 23 revolutions then insert theAllen Key to tighten until the screw isush with the shower screen. Do notovertighten screw.

8. Re-insert the drip tray and rearwater tank.

Contact Breville Consumer Support or visitwww.breville.com for replacement siliconeseals or for advice.

TROUBLESHOOTING


21/48

40 41

PAGE HEADER..... PAGE HEADER.....TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

The HOT WATERLED ashes when themachine is turned on

HOT WATER dial isOPEN.

Turn the HOT WATER dial tothe CLOSED position.

Machine beepswhen turned on

STEAM LEVER isOPEN or has beenactivated before themachine has reachedoperating temperature.

Move the STEAM LEVER tothe CLOSED position.

Water does not owfrom the group head

Machine has notreached operatingtemperature.

Allow time for the machine toreach operating temperature.The POWER button willstop ashing when machineis ready.

Water tank is empty. Fill tank.

Water tank is not fullyinserted and lockedinto position.

Push water tank in fully andlock latch closed.

FILL TANK on LCD,but water tank is full

Water tank is not fullyinserted and lockedinto position.

Push water tank in fully andlock latch closed.

No steam or hot water Machine is notturned on.

Ensure the machine isplugged in and the POWERbutton is on.

No hot water Water tank is empty. Fill water tank.

No steam Steam wand is blocked. Use the pin on the end of theprovided cleaning tool. Ifsteam wand remains blocked,remove the tip using theintegrated spanner in thecleaning tool and soak in hotwater. Screw tip back ontothe steam wand using theintegrated spanner in thecleaning tool.

TROUBLESHOOTING


The machine is on butceases to operate

Turn machine off. Wait for60 minutes and turn machineback on.If problem persists, callBreville Consumer Support.

Steam pouring out ofgroup head

Turn machine off. Wait for60 minutes and turn machineback on.If problem persists, callBreville Consumer Support.

Espresso only dripsfrom the portalterspouts, restricted ow

Coffee is groundtoo nely.

Use slightly coarser grind.

Too much coffee in thelter basket.

Lower dose of coffee bytamping then using the Razordose trimming tool to trim offexcess coffee.

Coffee tamped toormly.

Tamp between 3040lbsor 1520kg of pressure.

The lter basket may beblocked.

Use the ne pin on theprovided cleaning toolto clear the outlet hole(s) onthe under side of the lterbasket. If it continues to beblocked, dissolve a cleaningtablet in hot water and soaklter basket and portalterin the solution for approx.20 minutes. Rinse thoroughly.


22/48

42 43

PAGE HEADER..... PAGE HEADER.....TROUBLESHOOTING


Espresso runs out tooquickly

and/or

Pressure gauge notreaching 9 bar

The coffee is groundtoo coarse.

Use slightly ner grind.

Not enough coffee inthe lter basket.

Increase dose of coffee. Tampthen use the Razor dosetrimming tool to trim offexcess coffee.

Coffee not tampedrmly enough.

Tamp between 30-40lbsor 15-20kg of pressure.

If the above suggestions donot help, check the machine.Place an EMPTY Dual Walllter basket into the portalter(either 1 CUP or 2 CUP). Pressthe MANUAL button. If thepressure gauge reads over5 bar, the machine is workingcorrectly. Try re-pulling ashot, with coffee, using the 3suggestions above (ner grind,increase dose, increase tamp).If the pressure gauge readsbelow 5 bar, call BrevilleConsumer Support.

Coffee beans are stale. Use freshly roasted coffeebeans with a Roasted On dateand consume between520 days after that date.

Coffee not hot enough Cups not pre-heated. Rinse cups under hot wateroutlet and place on cup

warming tray. Milk not hot enough

(if making a cappuccinoor latt etc).

Heat milk until base ofthe jug becomes hotto touch.

Extraction temperatureis too low.

Increase extractiontemperature. See ExtractionTemperature, page 19.

TROUBLESHOOTING


No crema Coffee beans are stale. Use freshly roasted coffeebeans with a Roasted On dateand consume between520 days after that date.

Using Single Walllter baskets withpre-ground coffee.

Ensure you use Dual Wall lterbaskets with pre-ground coffee.

Espresso runs outaround the edge of theportalter

and/or

Portalter comes outof the group head

during an extraction

Portalter not inserted inthe group head correctly.

Ensure portalter is rotatedto the right until the handleis securely locked in place.Rotating past the center willnot damage the silicone seal.

There are coffeegrounds around thelter basket rim.

Clean excess coffee fromthe rim of the lter basket toensure a proper seal in grouphead.

Filter basket rim iswet or underside ofportalter lugs are wet.Wet surfaces reduce thefriction required to holdthe portalter in placewhilst under pressureduring an extraction.

Always ensure lter basket andportalter are dried thoroughlybefore lling with coffee,tamping and inserting into thegroup head.

Too much coffee in thelter basket.

After tamping, trim the coffeedose using the Razor dosetrimming tool.

Unable to set Auto

Start time

Clock not set or clock is

set with incorrect time.

Check that the clock and

Auto Start time have beenprogrammed correctly.The LCD will display a clockicon when the Auto Start timeis programmed.

E1, E2 or E3 errormessage on LCD

An error that cannotbe reset by the userhas occurred.

Call Breville ConsumerSupport.


23/48

44 45

PAGE HEADER.....TROUBLESHOOTING


Coffee puck is stickingto the shower screen

This is normal andhappens occasionally.The dry puck featurecreates a slightvacuum on top of thecoffee puck whichwill occasionally holdthe puck against theshower screen insteadof leaving it in the lterbasket.

Pumps continue tooperate / Steam isvery wet & spitty / Hotwater outlet leaks

Using highly ltered,de-mineralized ordistilled water whichis affecting how themachine is designed tofunction.

We recommend using cold,ltered water. We do notrecommend using waterwith no/low mineral contentsuch as de-mineralized ordistilled water. If the problempersists, contact BrevilleConsumer Support.

Too much coffeeextracted

Coffee is ground toocoarsely.

Shot duration/volume needs to bereprogrammed.

Adjust the grind sizeslightly ner. Tamp thenuse the Razor dosetrimming tool to trim offexcess coffee.

Reprogram the shotduration/volume.Refer to ReprogrammingShot Duration & Volume,page 18.


Not enough coffeeextracted

Coffee is ground toonely.

Shot duration/volume needs to bereprogrammed.

Adjust the grind sizeslightly coarser. Tampthen use the Razor dosetrimming tool to trim offexcess coffee.

Reprogram the shotduration/volume. Referto Reprogramming ShotDuration & Volume,page 18.

Amount of coffeeextracted haschanged, but allsettings are the same

As coffee beans age, theextraction rate changesand can affect the shotvolume.

Adjust the grind sizeslightly ner. Tamp thenuse the Razor dosetrimming tool to trim offexcess coffee.

Reprogram the shotduration/volume. Referto Reprogramming Shot

Duration & Volume,page 18. Use freshly roasted coffee

beans with a Roasted Ondate and consume between520 days after that date.

TROUBLESHOOTING


24/48

47

COFFEES TO TRYCOFFEES TO TRY

CAPPUCCINOA single shot of espresso with textured milk and garnished withdrinking chocolate.

ESPRESSOIntense and aromatic, it is also known as short black and isserved in a small cup or glass.

LATTA latt consists of a single espresso with textured milk andapproximately 10mm of foam.

MACCHIATOTraditionally served short, the macchiato is also poured as anAmericano with a dash of milk or a dollop of textured milk.

AMERICANOA shot of espresso (single or double) with hot water. Also knownas a long black.

RISTRETTOA ristretto is an extremely short espresso of approximately15ml, distinguished by its intense avor and aftertaste.


25/48

49

FLICITATIONSpour lachat de votre produit Breville

TABLE DES MATIRES

50 Breville vous recommande lascurit avant tout

53 Faites la connaissance de votreproduit Breville

57 Fonctionnement de votreproduit Breville

74 Trucs & prparation du caf

79 Entretien et nettoyage

86 Guide de dpannage

94 Suggestions de caf

*Lenregistrement nest pas un substitut la preuve dachatlorsque vous soumettez une rclamation de garantie.

Consommateurs amricains: www.brevilleusa.comConsommateurs canadiens: www.breville.ca

Inscrivez-vous en ligne pour le soutientechnique et les offres exclusives.*


26/48

50 51

BREVILLE VOUS RECOMMANDE LA SCURIT AVANT TOUT

Chez Breville, la scurit occupe une place de choix. Nous concevons et fabriquons desproduits de consommation sans jamais perdre de vue la scurit de notre prcieuse clientle.De plus, nous vous demandons dtre trs vigilant lorsque vous utilisez un appareil lectriqueet de respecter les mesures de scurit suivantes:

Lorsque vous utilisez un appareil lectrique,des mesures de scurit lmentairesdoivent tre respectes, incluant ce qui suit:

POUR TOUT APPAREILLECTRIQUE

Lisez attentivement toutes lesinstructions avant dutiliserlappareil et conservez-les pourrfrence future.

Ne touchez pas les surfaceschaudes de lappareil. Utilisezles poignes ou les boutons,tel quindiqu dans ce manueldinstructions.

Pour vous protger contre lesrisques de feu, de choc lectriqueou de blessures, nimmergez pasle cordon dalimentation, la cheou lappareil lui-mme dans leauou tout autre liquide.

Surveillez attentivement lesenfants qui utilisent ou sont proximit de lappareil.

Si lappareil doit tre:- laiss sans surveillance- nettoy- deplac- assembl ou- rangteignez-le toujours en pressantlinterrupteur, puis dbranchez-lede la prise murale.

Laissez toujours refroidirlappareil avant de le nettoyer, ledplacer ou le ranger.

Il est recommand de vrierrgulirement lappareil et lecordon dalimentation. Nutilisezpas lappareil si le cordon oula che dalimentation sontendommags ou si lappareilest dfectueux ou endommag.Cessez immdiatement lusagede lappareil et appelez le Soutienaux consommateurs de Breville.

Lutilisation daccessoires nonrecommands par Breville peutcauser un risque dincendie, dechoc lectrique ou de blessures.

IMPORTANTES MESURESDE SCURIT


Assurez-vous davoir bien insret verrouill le porte-ltre dansle groupe dinfusion avant dedbuter lextraction. Ne retirez jamais le porte-ltre durantlextraction.

Soyez prudent lors du dtartrage,car de la vapeur chaude pourraitschapper. Avant le dtartrage,teignez la machine, laissez-larefroidir au moins une heureet assurez-vous que le plateaudgouttage est vide et bieninsr. Voir les instructions deDetartrage (dESc) en page 82.

Ne tentez pas douvrir la machineou de la rparer.

Pour tout entretien autre que lenettoyage, appelez le Soutien auxconsommateurs de Breville ouconsultez un rparateur autorisBreville.

Ne laissez pas le cordondalimentation pendre dunetable ou dun comptoir ni toucherdes surfaces chaudes.

Ne placez pas lappareil surle bord dune table ou dun

comptoir. Assurez-vous que lasurface est de niveau, propre etbien assche.

Ne placez pas lappareil sur ouprs dun lment au gaz oulectrique et ne le laissez pasentrer en contact avec un fourchaud.

Cet appareil est recommandpour un usage domestiqueseulement. Ne lutilisez pas dautres ns que celles prvues.Ne lutilisez pas lextrieur nidans un vhicule ou un bateauen mouvement.

INSTRUCTIONS SPCIFIQUESPOUR LA BES920XL

Il est recommand de brancherla machine espresso dans uneprise relie la terre, sur uncircuit lectrique ddi et spardes autres appareils.

Remplissez le rservoir avecde leau froide seulement etnutilisez aucun autre liquide.Nutilisez pas deau hautementltre, dminralise ou distille,car elle affectera le got du cafet le mode de fonctionnement dela machine.


27/48

52


COURT CORDONDALIMENTATIONVotre appareil Breville est munidun court cordon dalimentationtrs scuritaire qui prvient lesblessures corporelles ou dommages

pouvant tre causs par le fait detirer, trbucher ou senchevtrerdans un cordon plus long. Lescordons dalimentation dtachablesou les cordes de rallonge peuventtre utiliss avec prcaution. Sivous utilisez une corde de rallonge:(1) sa capacit lectrique doit trequivalente ou suprieure lacapacit lectrique de lappareil;(2) la corde ne doit pas pendre

dun comptoir ou dune tableo de jeunes enfants pourraientsy suspendre ou trbucheraccidentellement; (3) la corde derallonge doit tre munie dune che trois broches relie la terre.

FICHE ASSISTMC DE BREVILLEVotre appareil Breville est munidune che exclusive AssistMC conue spcialement avec unanneau pour laisser passer un doigtet faciliter le retrait scuritaire dela che.

CONSERVEZ CES INSTRUCTIONS

INDICATION DU FACTEURDUTILISATION CSALAssociation canadienne denormalisation (CSA) exige que lefacteur dutilisation en minutessoit inscrit sur tout appareil

consommant plus de 1500 W.Pour la BES920XL, ce facteurdutilisation reprsente la duremaximale pour laquelle lappareilconsomme plus de 1500 W durantune priode dutilisation de 2heures. Cela ne signie pas pourautant que lappareil nest passecuritaire pour une utilisationcontinue ou quil doit tre teint intervalles donns durant un usage

normal.

PROPOSITION 65 DE LACALIFORNIE:(Applicable aux residents de laCalifornie seulement).Cet appareil contient des produitschimiques connus de ltat de laCalifornie comme pouvant causerle cancer, des malformationscongnitales ou tout autre problmede reproduction.

FAITES LACONNAISSANCE

de votre produit Breville

CARACTRISTIQUES DE VOTRE PRODUIT BREVILLE FAITES LA CONNAISSANCE DE VOTRE PRODUIT BREVILLE


28/48

54 55

CARACTRISTIQUES DE VOTRE PRODUIT BREVILLE

TRIPLE SYSTME DE CHAUFFAGE

Deux chaudires en acier inoxydableLes deux chaudires ddies la vapeuret lespresso moussent le lait et extraientsimultanment lespresso la tempratureoptimale.

Groupe dinfusion chauffage actif Groupe dinfusion commercial de 58 mmavec lment intgr, pour une stabilitthermique maximale durant lextraction.

CONTRLE DE PRCISION

Contrle lectronique de temprature PIDLe contrle lectronique de tempratureachemine leau une temprature prcisepour un espresso saveur optimale.Programmable.

Pression dextraction rguleLa soupape de surpression (SSP) gardela pression maximale au plus haut niveaudurant toute lextraction.

Prinfusion basse pressionLa pression augmente graduellement etgone lentement la mouture pour uneextraction uniforme. Programmable.

Deux pompesLes pompes ddies la vapeur et lespresso maintiennent une pression

constante tout au long de lextraction.Temprature dextraction programmableAjustez la temprature de leau pour obtenirun espresso savoureux, selon lorigine et ledegr de torrfaction des grains.

CARACTRISTIQUESADDITIONNELLES

cran ACL rtroclairAfche les rglages en cours et simplie laprogrammation des fonctions.

Vapeur instantane haut volumeLa chaudire vapeur de 950 ml (32 oz)produit une vapeur instantane et continue.

Buse vapeur commercialeBuse vapeur pivotant sur 360 en acierinoxydable avec embout 3 orices pourune texture veloute.

Eau chaude instantaneSortie dedie leau chaude pourAmericanos et prchauffage des tasses.

Porte-ltre en acier inoxydable de 58 mm

Favorise une extraction plus uniforme etfacilite le nettoyage.

Minuteur de lespressoAfche en temps rel la dure dextractionde lespresso.

Dmarrage automatiqueLa machine se met en marche au momentvoulu.

Outil de dosage de precision RazorMCLa lame du rasoir brevete coupe la rondellede caf au niveau requis pour un dosage

prcis et une extraction uniforme.

FAITES LA CONNAISSANCE DE VOTRE PRODUIT BREVILLE

A. Rservoir amovible de 2,5 L (84 oz) remplissage par le hautAvec ltre intgr et indicateur deniveau deau rtroclair.

B. Cadran deau chaudeTourner pour activer et arrter le dbitdeau de la sortie deau chaude.

C. InterrupteurD. cran ACL rtroclair

Afche les rglages en cours et simpliela programmation des fonctions.

E. Touche MENUUtiliser pour rgler les fonctions deprogrammation afches sur lcranACL.

F. Manomtre espressoContrle la pression dextraction.

G. Bourroir intgr amovible de 58 mmH. Groupe dinfusion chauff de 58 mm

avec lment intgrI. Porte-ltre en acier inoxydable

de 58 mm

J. Chauffe-tasseK. Touches 1 TASSE, 2 TASSES et

MANUALAvec dure prrgle, manuelle prioritaireou dure/volume reprogrammable.

L. Levier de vapeurPour vapeur instantane et continue.

M. Sortie ddie leau chaudeFournit leau chaude pour Americanos etprchauffage des tasses.

N. Buse vapeur pivotant sur 360Avec embout 3 trous pour une textureveloute.

O. Point daccs pour le dtartrageP. Tiroir de rangement

Pour ranger les accessoires non utiliss.Q. Pied pivotant rtractable

Soulve la machine pour faciliter ledplacement.

R. Plateau dgouttage amovibleAvec indicateur Empty me!(Videz-moi!).

HI

FG

DE

C

AB

J

K

L

M

NOP

RQA



29/48

56


I

H

A

DC

G

J

E

F

B

ACCESSOIRESA. Pichet lait en acier inoxydableB. Support du ltre eau et ltreC. Paniers ltres simple paroi de 1 TASSE & 2 TASSESD. Paniers ltres double paroi de 1 TASSE & 2 TASSESE. Disque de nettoyageF. Outil de dosage de prcision RazorMC (rasoir)G. Bandelette-test de duret de leauH. Pastilles de nettoyageI. Outil de nettoyage pour embout de buse vapeurJ. Cl Allen

FONCTIONNEMENTde votre produit Breville

FONCTIONNEMENT DE VOTRE PRODUIT BREVILLE FONCTIONNEMENT DE VOTRE PRODUIT BREVILLE


30/48

58 59

FONCTIONNEMENT DE VOTRE PRODUIT BREVILLE

AVANT LA PREMIRE UTILISATION

Prparation de la machineRetirez et disposez de tout matrieldemballage et tiquettes promotionnelles.Assurez-vous davoir en mains toutesles pices et accessoires avant de jeter lematriel demballage.Retirez le rservoir deau log larrirede la machine en tirant la poigne durservoir. Retirez le sac de plastiquecontenant le ltre eau et son support.Lavez les pices et accessoires (rservoir,porte-ltre, paniers ltres, pichet) leauchaude avec un savon dlicat, puis rincez fond.

TRUCPour dplacer facilement votre machine,utilisez le pied pivotant rtractable logsous le plateau dgouttage. Lorsquil est

tourn UNLOCK (dverrouiller), le pieddescend et soulve la machine, facilitantlaccs au rservoir deau amovible ou ledplacement de la machine.

INSTALLATION DU FILTRE EAU Retirez le ltre eau et son support du

sac de plastique. Faites tremper le ltre dans une tasse

deau durant 5 minutes puis rincez-le leau froide.

Lavez le support du ltre leau froide

en prenant soin de bien rincer lesmailles en acier inoxydable..

Faire tremper le filtre 5 minutes Rincer le filtre et les mailles

Insrez le tlre dans chacune des deuxparties du support.

Insrer le filtredans son support

Pour installer le support assembl aultre dans le rservoir, alignez la basedu support avec ladaptateur lintrieurdu rservoir. Appuyez pour bien leverrouiller.

Remplissez le rservoir deau froideavant de le glisser en place et de leverrouiller.

NOTE

NE PAS utiliser deau hautement ltre,dminralise ou distille, car cela peutaffecter le got du caf et le mode defonctionnement de la machine.

NOTEPour vous procurer des ltres eau,visitez www.breville.com ou appelezle Soutien aux consommateurs deBreville.


PREMIRE UTILISATION1. Assurez-vous davoir rempli le

rservoir deau froide. Pour ce faire,remplissez-le par le haut (appuyezpour louvrir) ou retirez-le de larrirede la machine.

2. Assurez-vous que le LEVIERDE VAPEUR et le cadran dEAUCHAUDE sont en position ferme(CLOSED).

3. Pressez linterrupteur pour fairedmarrer la machine.

4. Lcran ACL afchera Hrd3, vousinvitant rgler le niveau de duretde leau. Cette programmationdterminera la rgularit dusignal de changement de ltre(NEW FILTER), vous indiquantque le ltre eau doit tre remplac.

Rgler la duret de leau Retirez la bandelette-test de lemballage. Trempez la bandelette-test dans un

peu deau du rservoir et attendez uneminute. Le niveau de duret de leau estindiqu par le nombre de carrs rougesapparaissant sur la bandelette-test. Parexemple, 3 carrs rouges indiquent dergler la duret de leau 3.

Pressez la che du HAUT ou celle duBAS jusquau rglage requis, de Hrd1(trs douce) Hrd5 (trs dure). Pressezla touche MENU pour xer le rglage. Lamachine bipera une fois pour conrmervotre slection.

NOTESi aucune slection nest faite dansles 5 minutes qui suivent, la machineretournera au rglage par dfautHrd3.

5. Un son de pompage/vibration sefera entendre, indiquant que leschaudires vides sont en train de seremplir pour la premire fois. LcranACL afchera la temprature de lachaudire mesure quelle chauffe.

6. Aprs environ 10 minutes, lamachine atteindra la tempraturede fonctionnement par dfaut(93C/200F) et les 4 touchessallumeront. La machine est alorsen mode VEILLE, prte pour laprochaine tape Purger la machine.

POWER

NOTEVous ne pourrez slectionner les fonctions1 TASSE ou 2 TASSES. Accdez au cyclede nettoyage dans les options du menu,ou activez la buse vapeur jusqu ce quela machine ait atteint la tempraturede fonctionnement (mode VEILLE). Unsignal sonore se fera entendre 3 fois silune de ces fonctions est slectionne.



31/48

60 61

Purger la machineQuand la machine aura atteint le modeVEILLE, procdez comme suit:1. Pressez la touche 2 TASSES pour

faire passer leau dans le groupedinfusion durant 30 secondes.

2. Tournez le cadran dEAU CHAUDE la position ouverte (OPEN) pourlaisser leau scouler de la sortiedeau chaude. Aprs 30 secondes,tournez le cadran dEAU CHAUDE la position ferme (CLOSED).

3. Soulevez le LEVIER DE VAPEUR la position ouverte (OPEN) pourlaisser la vapeur schapper de labuse. Aprs 30 secondes, abaissez leLEVIER DE VAPEUR la positionferme (CLOSED).

4. Rptez les tapes 1-3 deux fois.5. Remplissez nouveau le rservoir

deau et videz le plateau dgouttage,si ncessaire.

MODE DCONOMIE DNERGIELa machine entrera en mode dCONOMIEDNERGIE aprs tre reste inactivependant 1 heure, et steindra si elle nest pasutilise pour une priode ininterrompue de4 heures.Si vous appuyez sur nimporte quelle touche

durant le mode dCONOMIE DNERGIE(sauf linterrupteur) ou actionnez le LEVIERDE VAPEUR ou le cadran dEAU CHAUDE,la machine chauffera pour atteindre latemprature de fonctionnement.Si vous appuyez sur linterrupteur durantle mode dCONOMIE DNERGIE, lamachine steindra.

CRAN ACL

Modes dafchage3 diffrents modes peuvent tre afchs surlcran ACL: la temprature de lespresso

(Shot temperature), le minuteur delespresso (Shot Clock) et lhorloge.Pressez la che du HAUT ou celle du BASpour changer le mode dafchage.

1. Temprature de lespresso (Shot Temp)Afche la temprature dextractionslectionne. Le rglage par dfaut est de200F (93C) mais peut tre modi de190F-205F (86C-96C). Voir Tempraturedextraction en page 65.

2. Minuteur de lespresso (Shot Clock)Afche en secondes la dure dextractionde lespresso. Voir Guide dextraction enpage 78.

Le minuteur de lespresso apparatra durantlextraction et 10 secondes aprs, puisretournera au mode dafchage par dfautde la temprature de lexpresso.

3. HorlogeAfche lheure actuelle. Le rglage pardfaut est 12:00AM (minuit), si vous navezpas rgl lheure. Voir Rgler lheure enpage 66.

Si lhorloge est slectionne, lheure resteraafche durant 10 secondes avant deretourner au mode dafchage par dfaut de

la temprature de lespresso.

FONCTIONNEMENT GNRALLes touches 1 TASSE & 2 TASSES utilisentla dure pour contrler le volume delespresso. La dure est prrgle, mais peuttre reprogramme (voir Reprogrammerla dure dextraction en page 64). Parcontre, vous pouvez accder aux fonctionsavances si vous dsirez utiliser le contrlevolumtrique au lieu de la dure (voirContrle volumtrique (vOL) en page 70.

TOUCHE 1 TASSEAppuyez une fois sur la touche 1 TASSEpour extraire un espresso simple ladure prrgle (30 secondes). Lextractiondbutera en utilisant la prinfusion bassepression.

La machine sarrtera aprs 30 secondes etretournera en mode VEILLE.

TRUCPour contourner la prinfusion bassepression et acheminer leau dans legroupe dinfusion pleine pression,pressez et tenez la touche 1 TASSSE.Relchez la touche lorsque le volumedespresso dsir sera extrait. Cettefonction peut tre utilise lorsquevous purgez le groupe dinfusion.




32/48

62 63

TOUCHE 2 TASSESAppuyez une fois sur la touche 2 TASSESpour extraire un double espresso ladure prrgle (30 secondes). Lextractiondbutera en utilisant la prinfusion bassepression.

La machine sarrtera aprs 30 secondes etretournera en mode VEILLE.

TRUCPour contourner la prinfusion basse

pression et acheminer leau dans legroupe dinfusion pleine pression,pressez et tenez la touche 2 TASSSES.Relchez la touche lorsque le volumede lespresso dsir sera extrait. Cettefonction peut tre utilise lorsquevous purgez le groupe dinfusion.

TOUCHE MANUELLELa touche MANUAL (manuelle) vouspermet de contrler la dure/volume delespresso selon vos prfrences. Pressezune fois la touche MANUAL pour dmarrerlextraction.Lextraction commencera en utilisant laprinfusion basse pression. Pressez nouveau la touche MANUAL pour arrterlextraction.

TRUCPour contrler manuellement la durede prinfusion basse pression,pressez et tenez la touche MANUAL(manuelle). Lorsque la dure deprinfusion requise aura t atteinte,relchez la touche pour activer lapleine pression. Pressez nouveaula touche MANUAL pour arrterlextraction.

VAPEURPour de la vapeur instantane, dplacez leLEVIER DE VAPEUR la position ouverte(OPEN). Le voyant DEL silluminera.

Pour arrter la vapeur, dplacez leLEVIER DE VAPEUR la position ferme(CLOSED). La machine retournera en modeVEILLE.

ATTENTION: RISQUE DE BRLURE

La vapeur pressurise peut encoreschapper de la machine, mme aprsquelle soit teinte.Surveillez toujours les enfants.

EAU CHAUDEPour de leau chaude instantane,tourner le cadran dEAU CHAUDE laposition ouvete (OPEN). Le voyant DELsilluminera.

Pour arrt leau chaude, tourner le cadrandEAU CHAUDE la position ferme(CLOSED). La machine retournera enmode VEILLE.

NOTE

Vous ne pouvez faire couler leauchaude et extraire lespresso enmme temps.

NOTELeau chaude cessera de couler aprsenviron 30 secondes. Selon le formatde votre tasse, vous pourriez devoirfermer puis rouvrir le cadran dEAUCHAUDE. Voir LE VOYANT DEAUCHAUDE clignote en page 71.




33/48

64 65

FONCTIONS PROGRAMMABLESPour entrer en mode de programmation,pressez la touche MENU. Tenez-la jusquce que la fonction dsire clignote surlcran ACL.Le mode de programmation vous permetde programmer:

Le volume de lespresso La temprature de lespresso Le dmarrage automatique Le cycle de nettoyage Lheure

Pour sortir du mode de programmation,pressez la touche EXIT.

NOTELa touche MENU sera dsactivedurant une extraction ou lcoulementde leau chaude.

REPROGRAMMER LA DURE DELESPRESSOLes touches 1 TASSE et 2 TASSES utilisentla dure pour contrler le volume delespresso. Reprogrammez la dure prrglede 30 secondes selon vos gots.Pressez la touche MENU jusqu ce que

SHOT VOL (volume de lespresso) clignoteet que 1 CUP ou 2 CUP soit afch, selonla touche que vous dsirez reprogrammer.Sans que le porte-ltre soit en place,appuyez sur la touche que vous dsirezreprogrammer (soit 1 TASSE ou 2 TASSES)pour faire passer leau dans le groupedinfusion. En suivant le minuteur delespresso sur lcran ACL, pressez la touche1 TASSSE ou 2 TASSES une fois que ladure requise aura t atteinte.

Reprogrammer la touche 1 TASSE

Reprogrammer la touche 2 TASSES

La machine bipera. Pressez la touche EXITpour rgler la nouvelle dure.

REPROGRAMMER LE VOLUMEDE LESPRESSOLes touches 1 TASSE et 2 TASSESutilisent la dure pour contrler le volumede lespresso. Accder aux fonctionsavances si vous dsirez utiliser le contrlevolumtrique au lieu de la dure pourdterminer le volume de lespresso (voirContrle volumtrique (vOL) en page 70.Suivez ensuite les instructions ci-aprs:Pressez la touche MENU jusqu ce queSHOT VOL (volume de lespresso) clignoteet que 1 CUP ou 2 CUP soit afch, selonla touche que vous dsirez reprogrammer.Doser et tasser la mouture dans leporte-ltre puis insrez-le dans le groupedinfusion. Pressez la touche que vousdsirez reprogrammer (soit 1 TASSE ou2 TASSES) pour activer lextraction delespresso. Pressez nouveau la touche1 TASSE ou 2 TASSES une fois que levolume dsire aura t extrait. La machinebipera. Pressez la touche EXIT pour rglerle nouveau volume.

TEMPRATURE DEXTRACTIONPressez la touche MENU jusqu ce queSHOT TEMP (temprature de lespresso)clignote. Lcran ACL afchera latemprature en cours.

Appuyez sur la che du HAUT ou celle duBAS BAS pour ajuster la temprature. Latemprature par dfaut est de 200F (93C)mais peut tre modie 190F 205F(86C 96C).

La temprature optimale dpendra delorigine des grains de caf, de leur fracheuret leur degr de torrfaction.Nous recommandons une tempratureentre 194F 203F (90C 95C) pour unesaveur optimale.La nouvelle temprature sera afche surlcran ACL. Pressez la touche EXIT pourla rgler.



34/48

66 67

RGLER LHEURELe rglage de lheure est facultatif. Pressez latouche MENU jusqu ce que SET CLOCKclignote. Lheure par dfaut est 12:00AM(minuit) si vous ne lavez pas dj rgle.

Pressez la che du HAUT ou celle duBAS pour rgler lheure. Pour acclrer ledlement, appuyez et tenez la che duHAUT ou celle du BAS. Pressez la touche

EXIT pour rgler lheure.

DMARRAGE AUTOMATIQUELe dmarrage automatique est facultatif.Il vous permet de programmer lemoment prcis o la machine dmarreraautomatiquement. En programmant votremachine, vous naurez pas attendre quelleprchauffe. Nous vous recommandonsde la programmer pour quelle dmarre15 minutes avant le moment prvu delutilisation.Pressez la touche MENU jusqu ce queAUTO START (dmarrage automatique)clignote et que le rglage de dmarrageautomatique en cours (ON ou OFF) soitafch sur lcran ACL.

Pressez la che du HAUT ou celle du BASpour rgler le dmarrage automatique ONou OFF (marche ou arrt).

Si OFF (arrt) est slectionn, pressez latouche EXIT pour rgler le dmarrageautomatique.

Si ON (marche) est slectionn, pressez latouche MENU. Appuyez sur la che duHAUT ou celle du BAS pour rgler lheuredu dmarrage automatique. Pour acclrerle dlement, pressez et tenez la che duHAUT ou celle du BAS.

Pressez la touche EXIT pour rgler ledmarrage automatique. Une petite icnedhorloge apparatra sur lcran ACL, unefois la fonction programme.

CYCLE DE NETTOYAGECe cycle nettoie lcran diffuseur et vidangele groupe dinfusion.Slectionnez cette fonction lorsque lemessage CLEAN ME! (Nettoyez-moi!)apparat sur lcran ACL. Voir CYCLE DENETTOYAGE en page 80.

FONCTIONS AVANCESCes fonctions sont rserves uniquementaux utilisateurs expriments.Pour accder aux fonctions avances,lorsque la machine est teinte, pressez ettenez la touche 1 TASSE, puis pressez ettenez linterrupteur. Appuyez sur la chedu HAUT jusqu la fonction dsire, puispressez la touche MENU pour accderaux rglages.Appuyez sur la touche EXIT en tout tempspour quitter ces fonctions.

POWER

POWER

TEINDRE

PRESSER & TENIR

PAGE HEADER.....FONCTIONNEMENT DE VOTRE PRODUIT BREVILLE



35/48

68 69

Rinitialiser les rglages par dfaut (rSEt)Utilisez cette fonction pour dsactivertous les rglages programmables et lesrinitialiser aux rglages par dfaut de lamachine qui sont les suivants:1. Temprature - 93C (200F)2. Prinfusion - Dure Pd07

3. Prinfusion - Puissance PP604. Temprature de la vapeur - 135C

(275F)5. Son de la machine - LO6. Arrt automatique - activ (ON)7. Dmarrage automatique - inactiv

(OFF)8. Units de temprature - Fahrenheit9. Duret de leau - Hrd310. Dure de lespresso - 30 sec.

Lorsque rSET apparatra sur lcran ACL,pressez la touche MENU pour rinitialisertous les rglages par dfaut. La machinebipera pour conrmer votre slection.

Hrd3 clignotera sur lcran ACL. Le modeDuret de leau est maintenant activ.Dterminez le niveau de duret laide dela bandelette-test fournie. Voir Rgler laduret de leau en page 59. Pressez la chedu HAUT ou celle du BAS pour le rglagerequis, de Hrd1 (trs douce) Hrd5 (trsdure). Pressez la touche MENU pour lergler. La machine bipera pour conrmer

votre slection.Le rglage de la duret de leau dterminerala frquence dalerte NEW FILTER(nouveau ltre) indiquant que le ltre eau du rservoir doit tre remplac.

Dtartrage (dESc)Slectionnez cette fonction pour accder,tape par tape, la procdure de dtartragesur lcran ACL. Voir les instructions lasection DTARTRAGE en page 68.

Units de temprature - C/F (SEt)

Rglez les units en mesures mtriques ouimpriales. Pendant que SEt est afch surlcran ACL, pressez la touche MENU, puisla che du HAUT ou celle du BAS pourchoisir les units. Rglez en pressant nouveau la touche MENU.

Temprature de la vapeur (StEA)

Rglez la temprature de la chaudire vapeur qui contrle aussi la pression de lavapeur. Abaissez la temprature pour fairemousser un plus petit volume de lait ou pouravoir plus de contrle. Augmentez-la pourmousser un plus grand volume de lait.Pendant que StEA est afch sur lcranACL, pressez la touche MENU, puis lache du HAUT ou celle du BAS jusqula temprature dsire. Rglez en pressant nouveau la touche MENU. La machinebipera pour conrmer votre slection.

Dsactiver larrt automatique (A OF)

Utilisez cette fonction pour dsactiverlarrt automatique (A OF).Pendant que A OF est afch sur lcranACL, pressez la touche MENU. Appuyezsur la che du haut (UP) ou celle du bas(DOWN) pour slectionner Off ou On(dsactiv ou activ). Pressez la toucheMENU pour rgler votre choix. La machinebipera pour conrmer votre slection.

Son de la machine (Snd)

Rgler les alertes sonores. Pendant queSnd est afch sur lcran ACL, pressez latouche MENU, puis la che du HAUT oucelle du BAS pour OFF (sourdine), LO (bas)ou HI (lev). Rglez en pressant nouveaula touche MENU. La machine bipera pourconrmer votre slection, selon le cas.

PAGE HEADER..... PAGE HEADER.....



36/48

70 71

Contrle volumtrique (vOL)

Slectionnez la mthode pour mesurer ladose de lespresso, base sur le volume (Flo)ou la dure (SEc). Pendant que vOL estafch sur lcran ACL, pressez la toucheMENU, puis la che du HAUT ou celle duBAS pour choisir la mthode dsire. Rglezen pressant nouveau la touche MENU.La machine bipera pour conrmer votreslection.

PROGRAMMER LA PRINFUSIONPendant que la machine est en marche eten mode VEILLE, pressez simultanmentles ches du HAUT et celle du BAS pourprogrammer le mode de prinfusion.Pressez la touche MENU pour choisir ladure de prinfusion (Pd) ou la puissancede prinfusion (PP).

Dure de prinfusion (Pd)Lcran ACL afchera la dure deprinfusion en cours.Pressez la che du HAUT ou celle duBAS pour varier la dure.

Nous recommandons une dure maximaleentre 515 secondes. Pressez la toucheMENU pour accder la puissance deprinfusion (PP), ou la touche EXIT pourrgler la dure slectionne.

Puissance de prinfusion (PP)Lcran ACL afchera la puissance de

prinfusion en cours.Pressez la che du HAUT ou celle duBAS pour varier la puissance.

Nous recommandons une puissancemaximale entre 5065. Pressez la toucheEXIT pour la rgler.

ALERTES

LE LEVIER DE VAPEUR bipe durantle rchauffageLa machine bipera 3 fois mais natteindrapas la temprature de fonctionnement(mode VEILLE) si le LEVIER DE VAPEURest en position ouverte (OPEN). Dplacezle LEVIER DE VAPEUR la position ferme(CLOSED).

LE VOYANT DEAU CHAUDE clignotedurant le rchauffageLa temprature de fonctionnement ne serapas atteinte (mode VEILLE) si le cadrandEAU CHAUDE est en position ouverte(OPEN). Le VOYANT DEAU CHAUDEclignotera. Dplacez le cadran dEAUCHAUDE la position ferme (CLOSED).

LE VOYANT DEAU CHAUDE clignotePour sassurer que leau est achemine labonne temprature, lcoulement de leauchaude cessera aprs environ 1 minute et leVOYANT DEAU CHAUDE clignotera.

Remplir le rservoirLa machine dtectera un bas niveau deau.Lcran ACL afchera FILL TANK.

Remplissez le rservoir deau froide. Lamachine ne pourra chauffer le caf oufournir de leau chaude si le rservoirest vide.

Nettoyez-moi!Le message CLEAN ME! (Nettoyez-moi!)indique que 200 extractions ont eu lieudepuis le dernier nettoyage.Cette fonction nettoie lcran diffuseur etvidange le groupe dinfusion. Pour plusdinformations sur la faon de nettoyer lamachine, voir CYCLE DE NETTOYAGEen page 80.

Changer le ltreLe message NEW FILTER sur lcran ACLindique que vous devez changer le ltre.Pour plus dinformations, voir Installer leltre eau en page 58.La frquence de ce message est dterminepar le rglage de la duret de leau (Hrd1-Hrd5) slectionn. Pour plus dinformations,voir Rgler la duret de l eau en page 59.

La temprature clignoteCela indique que la machine chauffe ou quela temprature a baiss considrablementdurant lusage.

EntretienPour assurer un rendement durable etoptimal dinfusion et de vapeur, il estimportant que la machine soit entretenuepar Breville ou un rparateur autorisBreville lorsque le message SERVICEapparat sur lcran ACL.Le message SERVICE (entretien)safchera aprs 6,000 cycles, soit environ4-5 ans dusage domestique normal. Cemessage a

bes920xl ib c13 fa lowres

Documents