beyer · pdf filebeyer gmbh maschinenbau und antriebstechnik safety devices: emergency power...
TRANSCRIPT
BEYER GmbHMaschinenbau und Antriebstechnik
37603 HolzmindenLüchtringer Weg 40
Telefon: +49 5531 61025Fax: +49 5531 4237
e-mail: [email protected]
BEYER GmbHMaschinenbau und Antriebstechnik
Belt cutting machine type WSM 101 / WSM 102Technical description:
The machine of the type WSM 101 (semi automatic) and WSM 102 (automatic) was engineered for cutting timing and flat belt sleeves. It is especially suitable for processing frequently changing sleeves and profile types with medium to high quantities. All common timing belt profile types can be processed.
Processing dimensions:� Max. belt length 5.800 mm� Min. belt length 130 mm (with device for cutting small belts)� Max. belt width 750 mm
Machine frame:� Stable, welded construction� Delivered as one unit� Affixing of the frame to the floor possible� All linear ducts are made of hardened, grinded steel shafts and ball bearings Tension slide:� Tension of the sleeve is variable min. 3 kp max. 140 kp� Moving of tension slide by drive motor� Angle of tension shaft variable Tool slide:� Semi-automatic processing WSM 101, controlled by PLC� Automatic processing WSM 102, controlled by PLC� Cutting die movement via ball screw driven by drive motor� Digital display of die position, cutting with and number of cuts� Cutting tool is a fixed round die� Tool holder exchangeable� Execution of cutting motion by lever (WSM 101)� Execution of the cutting motion automatically (WSM 102)
Cutting shaft:� Stepless rpm-control via frequency converter from 70 to 450 rpm� Rotation direction changable� Plastic sheath as wearout-cover, Ø 70 mm� Pneumatically triggered holder for supporting the cutting shaft Accessories:� Tool for exchanging the cutting shaft� Tool for exchanging the cutting die� Key for the wiring cabinet� Wiring diagram� Manual
BEYER GmbHMaschinenbau und Antriebstechnik
Safety devices:� Emergency power off� Safety knife cover� Tension is limited when using device for cutting small belts� Release of the tension only with closed holder of the cutting shaft� Overload protection of all drive motors
Special equipment:� Device for cutting small belts (min 130 mm in length, up to 450 mm belt width)� Semi-automatic control for the angle of the cutting shaft� Push-on shaft in addition to cutting shaft� Special die unit for cutting poly-v-rip belts� Cutting shaft in special diameters (40 mm, 50 mm, 100 mm)� Standby die (1.6 or 2.2 mm thick, Ø 100 mm)� Tool holder for additional die� Adjustment of the construction to special belt lengths on request� Adjustment of the construction to special belt widths on request
Size of the machine:Length: ca. 3,500 mmWidth: ca. 1,850 mmHeight: ca. 1,250 mm
Power supply:400 Volt, 3 Phases, 50 Hz, 16 AmpereCompressed air: 6 bar
Complete view on WSM 101
Belt cutting machine type WSM 101 / WSM 102
BEYER GmbHMaschinenbau und Antriebstechnik
Timing belt cutting machine type WSM 101 / WSM 102Photo gallery:
WSM 101 / WSM 102 Control elements
WSM 101 / WSM 102 Wiring CabinetWSM 101 / WSM 102 Cutting die
WSM 101 / WSM 102 Manual cutting shaftangle control
WSM 101 / WSM 102 Semi-automaticcutting shaft angle control
WSM 101 / WSM 102 Display
BEYER GmbHMaschinenbau und Antriebstechnik
Timing belt cutting machine type WSM 101 / WSM 102Photo gallery:
WSM 102 Automatic - Control ElementsWSM 101 / WSM 102 Deflection shafts
WSM 101 / WSM 102 Cutting tool forv-belts WSM 101 / WSM 102 Device for cutting small belts
and special cutting shafts
WSM 101 / WSM 102 Push-on shaft
BEYER GmbHMaschinenbau und Antriebstechnik
Belt cutting machine type WSM 100 / WSM 100-B
Technical description:
The machine of the type WSM 101 / WSM 100-B was engineered for cutting timing and flat belt pulleys. It is especially suitable for processing frequently changing sleeves and profile types with low to medium quantities. The WSM 100-B has the same functionality but is using low-cost machine parts. All common timing belt profile types can be processed.
Processing measurements:� Max. belt length 5.800 mm� Min. belt length 130 mm (with device for cutting small belts) � Max. belt width 750 mm
Machine frame:� Stable, welded construction� Delivered as one unit� Affixing of the frame to the floor possible� All linear ducts of the WSM 100 made of hardened, grinded steel shafts and bearing balls
Tension slide:� Tension of the sleeves is variable in 4 levels from 3 kp to 140 kp� Moving of tension slide b drive motor� Angle of tension shaft (Ø 100 mm) variable
Tool slide: � Cutting die movement via manually driven trapezoid screw spindle� Digital display of die position of cutting die� Cutting tool is a fixed round die� Tool holder exchangeable� Execution of the cutting motion via hand lever Cutting shaft:� Stepless variable rpm-control via frequency converter from 70 to 450 rpm� Rotation direction changable� Plastic sheath as wearout-cover, Ø 70 mm� Manual triggered holder for supporting the cutting shaft
Accessories:� Wiring diagram� Manual� Tool for exchanging the cutting shaft� Tool for exchanging the cutting die� Key for the wiring cabinet
BEYER GmbHMaschinenbau und Antriebstechnik
Safety devices:� Emergency power off� Safety knife cover� Release of the tightening of the belts only with closed holder
Special equipment:� Semi-automatic control for the cutting shaft angle� Push-on shaft in addition to cutting shaft� Special die for cutting poly-v-rip belts� Cutting shaft in special diameters (40 mm, 50 mm, etc.)� Pneumatically driven retainer for the cutting shaft� Standby knife (1.6 or 2.2mm thick, Ø 100 mm)� Tool holder for additional die Ø 100 mm
Size of the machine:Length: ca. 3,500 mmWidth: ca. 1,450 mmHeight: ca. 1,150 mm
Power supply:400 V, 3 Phases, 50 Hz, 16 A
Complete view on WSM 100 / WSM 100-B
Belt cutting machine type WSM 100 / WSM 100-B
BEYER GmbHMaschinenbau und Antriebstechnik
Belt cutting machine type WSM 100 / WSM 100-BPhoto gallery:
WSM 100 / WSM 100-B Control elements
WSM 100 / WSM 100-B Wiring Cabinet WSM 100 / WSM 100-B Cutting die
WSM 100 / WSM 100-B Manual cutting shaftangle control
WSM 100 / WSM 100-B Display
BEYER GmbHMaschinenbau und Antriebstechnik
Cutting machine type ZSM 150Technical description:
The machine of the type ZSM 150 was engineered for cutting long length timing belts.Single cuts are performed, so the coil is cut along its running direction. All common timing belt profiles can be processed.
Processing measurements:� Max. cutting width 150 mm� Max. coil diameter 1,000 mm
Machine frame:� Stable, welded construction� Delivered as one unit� Affixing of the frame to the floor possible� All linear ducts made of hardened, grinded steel shafts and ball bearings Tool sleigh:� Die movement via manually driven trapezoid spindle� Digital display of die position� Cutting tool is a fixed round die� Die position and cutting depth can be locked
Cutting shaft:� Stepless variable rpm-control via frequency converter� Rotation direction changable� Plastic sheath as wearout-cover for the cutting shaft� Foot switch for processing
Roll-up frame:� Clamping of the sleeve for rolling up� Manual lever for rolling up (automatic rolling up available as special equipment)
Accessories:� Tool for changing the dies� Key for the wiring cabinet� Wiring diagram� Manual Safety equipment:� Emergency power off� Safety die cover� Overload protection for drive motors
BEYER GmbHMaschinenbau und Antriebstechnik
complete view ZSM 150
Special equipment:� Automatic rolling up of the processed material� Standby die (thickness: 1.6 or 2.2mm, Ø 100 mm)� Length measurement of the processed material
Size of the machine:Length: ca. 2,500 mmWidth: ca. 1,200 mmHeight: ca. 2,200 mm
Power supply:400 V, 3 Phases, 50 Hz, 10 Ampere
Cutting machine type ZSM 150
BEYER GmbHMaschinenbau und Antriebstechnik
Cutting machine type ZSM 150Photo gallery:
ZSM 150 Control Elements
ZSM 150 Cutting unit
ZSM 150 Wiring Cabinet
BEYER GmbHMaschinenbau und Antriebstechnik
Cutting machine type BSM 120Technical description:
The machine of the type BSM 120 was engineered for cutting timing andflat belts. The machine is especially suited for cutting small numbers ofpieces. Sleeves and long length belts can be cut.
Processing measurements:� Max. cutting width 120 mm� Min. belt length 250 mm
Machine frame:� Stable, welded construction� Delivered as one unit � Insertion of long length belts on the frame� Guide table with edgewise clamped for cutting material Cutting shaft:� Stepless variable rpm-control via frequency converter (2 to 10 m/s)� Rotation direction changable� Distance sleeves between the round dies� Plastic sheath on the counter-pressure shaft� Manually fixation of cutting depth� Fast switch for processing
Accessories:� Tool for exchanging the cutting die� 5 dies� 1 set distance sleeves� Wiring diagram� Manual Safety devices:� Emergency power off� Safety die cover� Tool rest on the frame� Overload protection for the drive motor
Special equipment:� Standby knife (thickness: 2.0 mm, Ø 60 mm)� Additional distance sleeves
Size of the machine:Length: ca. 800 mmWidth: ca. 600 mmHeight: ca. 1,100 mm
Power supply:230 V, 50 Hz, 10 Ampere