biofilms on silicone rubber materials for outdoor high ...7667/fulltext01.pdf · biofilms on...
TRANSCRIPT
![Page 1: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/1.jpg)
BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH
VOLTAGE INSULATION
Stina Wallström
AKADEMISK AVHANDLING Som med tillstånd av Kungliga Tekniska Högskolan i Stockholm framlägges till offentlig granskning för avläggande av teknisk doktorsexamen torsdagen den 21 april 2005, kl. 13.00 i Kollegiesalen, Valhallavägen 79, KTH, Stockholm. Avhandlingen försvaras på svenska.
![Page 2: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/2.jpg)
![Page 3: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/3.jpg)
To Anders
![Page 4: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/4.jpg)
![Page 5: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/5.jpg)
ABSTRACT Silicone rubber high voltage insulators are sometimes colonised by microorganisms which form a biofilm on the surface of the infected unit. In this work insulators exposed to the outdoor environment in Sweden, Sri Lanka and Tanzania respectively have been studied. The biofilms colonising the insulators were shown to be of roughly the same composition regardless of their origin. Algae in association with bacteria dominated the biofilms and provided nutrition to mold growth. The isolated microorganisms were further used to study the effect of a biofilm on different silicone rubber materials. New tools for diagnosing biological growth on polymeric materials were developed and used to analyse the silicone rubber samples. No evidence of biodegradation of the polydimethylsiloxane (PDMS) molecule has been found in this work. However, this does not mean that PDMS rubbers used in high voltage insulators can be called bioresistant. Silicone insulating materials always contain additives and these may promote or hinder growth. For this reason, an extensive test program was developed, in order to evaluate the effect of different additives on the degree of biological growth. The program spanned from fast and easy methods, useful for screening large amount of samples, to the construction of specially designed microenvironment chambers in which mixed biofilms, similar to those formed on the surface of silicone rubber insulators in the field, were successfully grown. The test program showed that the flame retardant zinc borate protected the materials, whereas alumina trihydrate (ATH) did not hinder biological growth. On the contrary, environmental scanning microscopy (ESEM) in combination with X-ray energy dispersive spectroscopy (EDS) showed that the surface roughening caused by the addition of ATH to the silicone rubber matrix made the materials more difficult to clean. Furthermore when the hydrophobic surface of a silicone rubber insulator is covered by a hydrophilic biofilm this leads to a reduction of the surface hydrophobicity of the material. This may alter the electrical properties of the insulator. It is therefore important to develop methods to identify biofouled units. In this work, laser-induced fluorescence (LIF) spectroscopy was explored as a tool for the detection of biofilms on silicone rubbers. The experiments revealed that weak traces of algae or fungal growth, even those not visible to the naked eye, could be detected by this technique. In addition, it was shown that photography and subsequent digital image analysis could be utilised to estimate the area covered by biofilm growth. The results obtained indicate that LIF spectroscopy in combination with image analysis could be used for field diagnostics of biological growth on insulators in service.
![Page 6: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/6.jpg)
![Page 7: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/7.jpg)
LIST OF PAPERS
This Thesis is a summary of the following papers Paper I Wallström, S., Dowling, K., and Karlsson, S., Development and comparison of
test methods for evaluating formation of biofilms on silicones. Polymer Degradation and Stability, 2002. 78(2): p. 257-262.
Paper II Wallström, S. and Karlsson, S., Biofilms on silicone rubber insulators; microbial
composition and diagnostics of removal by use of ESEM/EDS. Polymer Degradation and Stability, 2004. 85(2): p. 841-846.
Paper III Wallström, S., Strömberg, E., and Karlsson, S., Microbiological growth testing of
polymeric materials: an evaluation of new methods. Polymer Testing, 2005: In press
Paper IV Wallström, S., Dernfalk, A.D., Bengtsson, M., Kröll, S., Gubanski, S.M., and
Karlsson, S., Image analysis and laser induced fluorescence combined to determine biological growth on silicone rubber insulators. Polymer Degradation and Stability, 2005: 88(3): p 394-400
Paper V Wallström, S. and Karlsson, S., Effects of microbiological growth on PDMS
materials. Manuscript, to be submitted to polymer degradation and stability. Paper VI Bengtsson, M., Wallström, S., Sjöholm, M., Grönlund, R., Andersson, M.,
Larsson, A., Karlsson, S., Kröll, S., and Svanberg, S., Fungus covered insulator materials studied with laser induced fluorescence and principal component analysis. Applied Spectroscopy, 2005: Submitted.
Paper VII Bengtsson, M., Grönlund, R., Sjöholm, M., Abrahamsson, C., Dernfalk, A.D.,
Wallström, S., Larsson, A., Weibring, P., Karlsson, S., Gubanski, S.M., Kröll, S., and Svanberg, S., Fluorescence lidar imaging of fungal growth on high-voltage outdoor composite insulators. Optics and Lasers in Engineering, 2005. 43(6): p. 624-632.
![Page 8: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/8.jpg)
THE AUTHOR’S CONTRIBUTION The author was responsible for and carried out the major part of the work in paper I-V In paper VI the author was responsible for sample preparation and assisted in the measurement of fluorescence, the analysis of the data and the writing of the paper. In paper VII the author was responsible for sample preparation and microscopy and assisted in the analysis of the data. Mathematical processing of data from fluorescence measurements and image analysis were performed by Magnus Bengtsson and Andreas Dernfalk respectively in all studies performed.
![Page 9: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/9.jpg)
TABLE OF CONTENTS
1 PURPOSE OF THE STUDY ..........................................................................................1
2 INTRODUCTION ...........................................................................................................3
2.1 HIGH VOLTAGE INSULATORS ......................................................................................3 2.2 PROPERTIES OF SILICONE RUBBER ..............................................................................4 2.3 DEGRADATION MECHANISMS......................................................................................5 2.4 DIAGNOSTIC METHODS ...............................................................................................6
2.4.1 Accelerated ageing.............................................................................................6 2.4.2 Analytical tools ..................................................................................................6 2.4.3 On-line measurements .......................................................................................7
2.5 COMPOSITION OF BIOFILMS.........................................................................................8 2.6 DAMAGES CAUSED BY BIOFILMS.................................................................................9
2.6.1 Fouling...............................................................................................................9 2.6.2 Degradation of leaching components ................................................................9 2.6.3 Biotic degradation ...........................................................................................10 2.6.4 Hydration and penetration...............................................................................11 2.6.5 Color and odor.................................................................................................11
2.7 PREVENTION OF MICROBIOLOGICAL GROWTH...........................................................11 2.7.1 Biocides............................................................................................................11 2.7.2 Cleaning...........................................................................................................12 2.7.3 Surface modification ........................................................................................12
3 EXPERIMENTAL.........................................................................................................13
3.1 MATERIALS ..............................................................................................................13 3.1.1 Silicones ...........................................................................................................13 3.1.2 Insulators .........................................................................................................14 3.1.3 Microorganisms ...............................................................................................14
3.2 GROWTH TESTS.........................................................................................................15 3.2.1 Powder test, mold.............................................................................................16 3.2.2 Powder test, algae............................................................................................16 3.2.3 IEC 68-2-10, mold ...........................................................................................16 3.2.4 ASTM G21-90, mold ........................................................................................16
![Page 10: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/10.jpg)
3.2.5 ASTM D 5589-97, algae ..................................................................................16 3.2.6 Quick test, mold ...............................................................................................17 3.2.7 Microenvironment chambers ...........................................................................17
3.3 LASER-INDUCED FLUORESCENCE..............................................................................18 3.4 IMAGE ANALYSIS ......................................................................................................19 3.5 DEGRADATION STUDIES............................................................................................20
3.5.1 Enzymatic degradation ....................................................................................20 3.5.2 Degradation by Fenton mechanism .................................................................21
3.6 INSTRUMENTATION...................................................................................................21 3.6.1 Oxygen plasma ageing.....................................................................................21 3.6.2 Light microscopy..............................................................................................21 3.6.3 SEM..................................................................................................................21 3.6.4 ESEM/EDS.......................................................................................................21 3.6.5 IR......................................................................................................................21 3.6.6 GC/FID ............................................................................................................22 3.6.7 SEC ..................................................................................................................22
4 RESULTS AND DISCUSSION ....................................................................................23
4.1 COMPOSITION OF BIOFILMS.......................................................................................23 4.2 EFFECT OF ADDITIVES...............................................................................................24
4.2.1 Powder tests.....................................................................................................24 4.2.2 Tests of silicone rubbers ..................................................................................25
4.3 DETERMINATION OF BIOFOULING .............................................................................28 4.3.1 Image analysis .................................................................................................29 4.3.2 Laser-induced fluorescence .............................................................................30 4.3.3 Hydrophobicity ................................................................................................33 4.3.4 ESEM/EDX ......................................................................................................34
4.4 BIODEGRADATION OF THE PDMS MOLECULE...........................................................37
5 CONCLUSIONS ............................................................................................................41
6 FUTURE WORK...........................................................................................................43
7 ACKNOWLEDGEMENTS ..........................................................................................45
8 REFERENCES ..............................................................................................................47
![Page 11: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/11.jpg)
————— Purpose of the study —————
1
1 PURPOSE OF THE STUDY
Silicone rubber high voltage outdoor insulators are sometimes colonised by microorganisms which form a biofilm on the surface of the infected units. This problem was first noted in tropical climates[1-8], but it has now also been observed in temperate environments [9-11]. Since silicone rubbers are considered to be bioresistant materials, the biofouling problem was not expected and little reported research could be found in relevant areas [12-14]. This project was initiated to develop knowledge of the effects of a biofilm on silicone rubbers used as high voltage insulating materials. Areas of interest for this study included the identification of the microorganisms causing the observed fouling problem, the examination of their effect on the chemical and mechanical properties of infected materials, and the evaluation of different silicone rubber formulations with respect to their ability to hinder biological growth. In addition, potential test methods for the identification of infected silicone rubber insulators in use were explored.
![Page 12: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/12.jpg)
————— Purpose of the study —————
2
![Page 13: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/13.jpg)
————— Introduction —————
3
2 INTRODUCTION
2.1 HIGH VOLTAGE INSULATORS An electrical insulator in a high voltage system is designed to support a charged conductor and electrically isolate it. Insulators made from glass or porcelain have been used for this purpose in power transmission lines for over 120 years. Over the last 40 years new designs have been developed and used for the construction of high voltage insulators. A modern composite insulator, as shown in Fig 2.1, consists of a mechanically supporting structure covered by a housing. The main functions of the housing are to protect the core from environmental stresses and to minimise leakage currents between the energised end and ground [14, 15]. The core often consists of a glass-fibre reinforced resin-bonded rod onto which two metal end-fittings are attached. The housing is made from polymeric materials such as EPDM or silicone rubber. Today it is widely agreed that regarding service performance and ageing, silicone rubber is the best housing material available [16].
Figure 2.1 a) Schematic drawing of a composite insulator. b) Picture of two silicone rubber insulators.
a) b)
![Page 14: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/14.jpg)
————— Introduction —————
4
2.2 PROPERTIES OF SILICONE RUBBER Silicone elastomers made from crosslinked polydimethylsiloxane (PDMS) (Fig. 2.2) mixed with suitable fillers and additives are used in many applications such as medical devices, textile coatings, foams, seals and electrical insulation. The silicone elastomers used as high voltage insulation materials generally contain at least two kinds of fillers, reinforcing fillers to improve the mechanical properties and a flame retardant filler to dissipate heat from energetic events in the high voltage system. Silica is the most common reinforcing filler and the most commonly used flame retardant is alumina trihydrate (ATH) [17]. Furthermore, additives such as antioxidants, colorants, crosslinking agents, processing aids and stabilisers are often used. The types and amounts of fillers are of major importance for the properties of the rubber.
Fig 2.2 The repeating unit of PDMS PDMS molecules display low intermolecular forces, high intramolecular siloxane bond energy, high backbone flexibility, and a partially polar backbone. These characteristics give PDMS-rubber a number of properties that make the material suitable for the production of high-voltage insulators [18]:
Good dielectric properties High surface mobility Excellent resistance to weathering Low surface free energy Hydrophobic surface properties Non-adhering surface Insolubility in water Low glass transition temperature High thermal and oxidative stability Low reactivity, toxicity and combustibility
The low surface free energy of a silicone rubber means that the material has excellent surface hydrophobicity. In addition, silicone rubber has the potential to recover this feature after exposure to ageing factors in the environment. Several plausible mechanisms for the hydrophobic recovery are suggested in the literature However, most researchers believe that the migration of low molar mass PDMS is the dominant mechanism for the hydrophobic recovery [19].
Si O
CH3
n
CH3
![Page 15: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/15.jpg)
————— Introduction —————
5
Other advantages of silicone rubber insulators over conventional porcelain insulators are that they are less attractive targets to vandals, and their lightweight and minor vulnerability make them easy to store, transport and install [20]. The possibility of producing insulators with a smaller surface area and a long leakage path is also advantageous, and this improves the function of the insulator under wet and contaminated conditions [15, 21]
2.3 DEGRADATION MECHANISMS Even though silicone rubbers (SIR) have a number of characteristics that make the materials suitable for high voltage applications, rubbers are more sensitive than inorganic materials to degradation under exposure to discharges and arcing [22, 23]. Surface-eroding climatic factors such as wind, rain, temperature, and UV radiation, also contribute to the degradation of the rubber, despite the fact that silicones are known to exhibit excellent resistant to weathering. [19, 22, 24, 25]. Electric fields at the edges of high voltage insulators or around water droplets on a hydrophobic silicone rubber surface can give rise to corona discharges [26]. These discharges produce a temporary loss of hydrophobicity [27, 28]. When hydrophobicity is lost, dry-band arcing capable of decomposing the polymeric material may occur [29]. Dry- band arcing causes tracking and erosion and the heat generated can seriously damage the insulating material [30, 31]. Low molecular weight (LMW) silicones, which contribute to the hydrophobic recovery, have relatively low boiling temperatures (<400C), which means that LMW silicones evaporate from the rubber at the elevated temperatures reached [32]. However, the generated heat also form new LMW-chains by inducing chain scission reactions in the material [25, 33]. In addition to electrical ageing factors, silicone rubbers used in high voltage insulators are exposed to severe environmental stresses such as UV-radiation. Even though PDMS-rubber is known to be very stable towards UV-radiation from sunlight, prolonged exposure can lead to crosslinking reactions in the surface of the material [34, 35]. It is also known that exposure of fouled SIR surfaces to UV increases the rate of hydrophobic recovery; indicating that chain scission reactions producing LMW-silicones are induced [36]. All PDMS-materials are highly insoluble in water, but this does not mean that organosilicones do not interact with humid surroundings. For example, water on the surface of silicone rubber gives a temporary loss of hydrophobicity by reorientation of methyl groups and by solubilisation of LMW chains [37]. Acid rain may also affect silicone rubbers. Artificial acid rain with pH 1.5-2.5 has been shown to cause chemical changes in the rubber matrix [38]. Even though natural rainfall never reaches such a low pH, acid rain may still harm an insulator. Fillers such as ATH are more sensitive to acidic pH and can be eroded by acid rain with a pH of about 5 [39]. However, diffusion of LMW-silicones helps silicone rubber materials to recover their original surface properties even after severe exposure to acid rain [40].
![Page 16: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/16.jpg)
————— Introduction —————
6
Degradation of PDMS through clay-catalysed hydrolysis is a well studied phenomenon [41, 42]. Clay minerals in soil are able to catalyse the hydrolysis of PDMS to dimethylsilanediol, a substance that is accessible to microorganisms and can be biodegraded to CO2, SiO2 and H2O [43-45]. However, organosilicones of higher molecular weight do not provide an easily accessible carbon source for microorganisms. Silicones are artificial materials, and no biological process is known that produces or degrades the covalent bonds of a PDMS-molecule [46]. Therefore, PDMS-materials always respond as bioresistant in biodegradability tests [42]. Nevertheless microorganisms can affect silicone rubber by several different mechanisms, as will be discussed further.
2.4 DIAGNOSTIC METHODS
2.4.1 Accelerated ageing The diverse interactions of a silicon rubber insulator with its surrounding environment mean that it is complicated to create relevant procedures to simulate the ageing of insulating materials. Even the most ambitious test programs often fail to represent true service conditions [10, 47]. In spite of this, several methods have been designed to test the performance of an insulator or a silicone rubber under the influence of accelerated ageing. Insulators or test rods can be placed in a fog chamber, were they are energized and exposed to artificial fog, often contaminated with salts or other eroding substances [48, 49]. Tracking wheel tests where samples are dipped in a water-bath and subsequently exposed to a high voltage are also common. [50]. Weatherometer ageing is another method often used to simulate the combined effects of several climatic ageing factors such as UV-radiation, elevated temperature, temperature cycling, thermal shock, high humidity and gaseous contamination. The electrical performance of the insulators or materials is recorded during the tests in order to determine the resistance of the samples to the applied stresses [51]. To reduce the risk of artefacts, insulators can be aged under field conditions. This is time-consuming, but the results obtained are adequate and useful [52, 53]. An unforeseen ageing factor discovered during field ageing was the biofouling of silicone rubber. Insulators aged outdoors in a tropical climate were found to be covered with a greenish-black film of biological origin [2]. None of the techniques for accelerated ageing address the problem of biological growth on the surface of an insulating material.
2.4.2 Analytical tools Numerous analytical techniques are suitable for studying the changes in the chemical and morphological characteristics of silicone rubber. One often used tool is scanning electron microscopy (SEM), with which it is possible to monitor the surface microstructure of a rubber and thus study morphological changes. After corona exposure, small cracks can be observed at the sample surface. Thermal stress also causes cracks, and UV-radiation makes ATH filler particles appear on the surface of the material [25, 54]. If chemical changes in the silicone
![Page 17: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/17.jpg)
————— Introduction —————
7
material are to be observed, techniques such as Fourier transform infrared spectroscopy (FTIR) or Electron spectroscopy for chemical analysis (ESCA) are needed. FTIR is commonly used to verify scission or recombination of chemical bonds in the surface layer of silicone rubber, such as the silanol groups formed by oxidation reactions induced by UV-exposure, corona or dry-band arcing [25]. ESCA can be used to study the proportions of different elements at the surface of a silicone rubber insulator. The of C/Si and Si/Al ratios indicate the magnitude of ageing in PDMS and the amount of ATH filler respectively [25, 55]. Another feature that is often affected by ageing is the surface hydrophobicity of the silicone rubber [25, 54]. The most common method used to study the loss and recovery of hydrophobicity is water contact angle measurement. By measuring the angle between the silicone rubber surface and a drop of water, the hydrophobicity of the material can be assessed [22]. Low molecular weight silicones, important for the hydrophobic recovery of a silicone rubber, can be detected by gas chromatography (GC) [56, 57]. If PDMS-oils of higher molecular weights are to be studied, size exclusion chromatography (SEC) is a reliable and often used method [33, 56, 58].
2.4.3 On-line measurements Today there is no standardised or widely used technique for the inspection of composite insulators in service [21]. Nevertheless a majority of utilities examine the condition of their insulators on the line [59]. The most common inspection technique used is visual examination. An experienced inspector can detect surface damage as well as evidence of internal faults just by looking at an insulator. Night vision equipment also enables discharge activity on the surface of the insulator to be distinguished [21, 59, 60]. Manual inspection is however operator-dependent and more objective techniques would be preferred. Infra-red thermography exploits the fact that the degradation caused by electrical events in the high voltage system is associated with heat. The infra-red radiation produced can be used to locate defects in composite insulators from the ground. Electrical field measurement is another promising method for the detection of faulty insulators. At the location of a defect, the electrical field is changed and this change can be recorded. However it is necessary to climb the tower to perform the measurement [59-61]. One disadvantage with the described techniques is that they only detect large defects like puncture and cracks, not fouling or other changes in surface properties of the insulator. New diagnostic methods are needed to detect smaller defects. Digital image analysis is one potentially useful technique. Information extracted from digital images of aged insulators enables features such as loss of hydrophobicity or extent of biofouling to be assessed. [62-65]. Laser-induced fluorescence offers another solution to the problem. By measuring the spontaneous emission of radiation by which electrons in atoms or molecules relaxes from an upper energy level to ground state level, changes in material properties of an insulator can be observed and biological growth detected [66-69].
![Page 18: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/18.jpg)
————— Introduction —————
8
2.5 COMPOSITION OF BIOFILMS Microorganisms colonising a bioresistant substrate tend to form a film on the surface of the material. Such a biofilm consists of microorganisms embedded in a highly hydrated matrix of extracellular polymeric substances (EPS), mainly polysaccharides and proteins. Mixed populations of bacteria, fungi, protozoa and algae often coexist in the film [70]. However, in a mature biofilm, the fraction of living cells is often small. Water is the most abundant element in most biofilms and the organic portion of the film is often dominated by EPS. In addition, particulate matter such as clay, humic substances, corrosion products etc. can be included in the mature biofilm. When the cause of a biofouling problem is being sought, it is easy to overlook the small content of microorganisms in the biofilm; thus neglecting the cause of the fouling [71]. Biofilm formation is an interfacial process, and surface features of the microorganisms and the substrate material are important for biofilm adhesion and growth. Interaction forces between adhering cells and substrate, such as van der Waals forces, electrostatic forces and acid base interactions, are of great importance for the initial microbial adhesion [73]. These forces, together with several other factors, some of them summarised in Tab. 2.1, also influence the growth rate and strength of adhesion of a biofilm [72]. Table 2.1 Factors affecting the adhesion and growth of a biofilm Genotypic factors Expression of genes encoding surface properties,
formation of EPS, growth rate etc. Physio-chemical factors Substrate composition and roughness, temperature, pH,
water potential, oxygen supply, etc. Stochastic processes Initial colonisation and random changes in biotic and
abiotic factors. Deterministic phenomena Specific interactions between organisms, competition,
co-operation, predation, etc. Mechanical Processes Shear from water or airflow over the substrate
surface. The structure of the biofilm formed varies, depending on the interactions of the microorganisms with the surrounding environment. However, most biofilms have a sponge-like structure containing a system of pores and channels in which a liquid phase is free to move and transport oxygen and nutrients between different parts of the biofilm [72, 74] From an ecological point of view, life in a biofilm offers many advantages to a cell; such as protection against desiccation, accumulation of nutrients from the bulk water phase, protection against toxic substances, facilitated exchange of genetic material and opportunities for co-metabolism [70, 72] The incitement for biofilm formation is therefore strong and biofilms are abundant in nature.
![Page 19: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/19.jpg)
————— Introduction —————
9
2.6 DAMAGES CAUSED BY BIOFILMS A biofilm can affect the properties of a polymeric material by several different mechanisms. Undesired effects range from discoloration to complete degradation of the polymeric material. Some of the major damaging mechanisms are summarised in figure 2.3 [70].
Figure 2.3 Undesired effects caused by a biofilm
2.6.1 Fouling Many polymeric materials are considered to be inert to microbial attack. However, these materials may still function as a support for a biofilm. The unwanted deposition of biological matter is referred to as fouling [75]. If the colonised material resists degradation, microorganisms can use pollutants from the surroundings to gain nutrition [76-78]. This was the case at a Florida-based transmission station where silicone bushings were trapping airborne pine pollen that served as a feedstock for a severe mould growth [8]. This ability of a biofilm to use an external carbon source makes laboratory testing difficult. Materials that seem to be inert in degradation studies may nevertheless encourage growth when exposed to outdoor conditions [79]. A fouling problem does not change the bulk properties of the infected material; it can however disturb the surface properties of the colonised object. When a silicone rubber insulator is covered by a hydrophilic biofilm, the hydrophobic surface properties are reduced. This has been shown to cause an increase in leakage current under wet conditions, compared to clean insulators [8].
2.6.2 Degradation of leaching components Plastics and rubbers often contain additives and impurities that may leak from the matrix to the surroundings and interact with a biofilm. Impurities such as unreacted low molecular weight material and residual processing aids can provide nutrients for an attached biofilm [77]. Fillers such as adiapates, epoxidised fatty acids, oleates, stearates and polyesters are also known to serve as nutrients for biological growth [80]. The same is true of carbon-based plasticizers and many other additives [70, 77, 80]. There are indications that some silicone
Proces
Effect
Polymer
Fouling Degradation of leaching components
Change in surface properties
Loss of stability
Loss of stability
Conductivity Swelling
Change in appearance
Biotic degradation
Hydration Penetration
Colour
Biofilm Enzymes Radicals
![Page 20: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/20.jpg)
————— Introduction —————
10
rubber materials used in high voltage insulators contain additives susceptible to microbiological attack [7, 10]. In contrast, accelerators such as dithiocarbamates and sulphur-based components may inhibit growth, as may residual heavy metal catalysts and many other additives [77, 80]. Field studies have shown that not all insulators are affected by biological growth. This may be due to the protective effect of additives used in the production of the silicone rubber.
2.6.3 Biotic degradation If a polymer is to be used as a source of nutrition for biological growth, it has to be degraded to segments small enough to be transported across the cell membrane [81]. This degradation can be mediated by degrading factors in the surrounding environment, such as wind, rain, oxygen, UV-radiation etc [82]. However, degradation can also be directly initiated by the living cell through the production of degrading substances such as enzymes, radicals or organic acids [82-86]. Surface degradation is an interfacial process depending on parameters such as pH, redox potential and the concentration of oxygen and salts. Biofilms can strongly influence these parameters [70]. Microorganisms sometimes excrete organic acids as by-products of metabolism. The excretion of organic compounds is usually the result of an unbalanced growth, a surplus or a limited supply of some compound essential for the metabolism of the microorganism. Anions, that are final products of microbial metabolism, react with cationic components and form salts. An increase in the salt concentration or a drop in the pH may facilitate the breakdown of the polymer [85]. Microorganisms can also incite the breakdown of an insoluble polymeric material by the production of exoenzymes, capable of mediating degradation outside the cell. It has been suggested that siloxane oils degrade under the influence of enzymes produced by bacteria [87], and there are indications that silicone rubber voice prostheses degrade under the influence of a mixed biofilm [88, 89]. The three most probable processes by which enzymes influence polymer degradation are [84]:
1. Hydrolysis by lysosomal enzymes of susceptible polymers 2. The oxidation of polymers by oxidase enzymes 3. The breakdown of natural biopolymer structures by enzymes such as collagenase
Many molds develop powerful enzyme systems with the ability to degrade highly stable polymeric structures. Among these, the white rot fungi hold a unique position. This class of molds has developed non-specific mechanisms for degrading the complex polymeric structure of lignin. The enzyme system responsible for the degradation includes peroxidases that promote the reduction of peroxides to free radicals [90-93]. It has been suggested that the white rot fungus Phanerochaete chrysosporium is able to degrade PDMS as well as lignin [94].
![Page 21: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/21.jpg)
————— Introduction —————
11
2.6.4 Hydration and penetration Fungal hyphae can penetrate their support and thereby cause cracks and pores in the material. The mechanism of the penetration is unclear, but it is known that hyphae are able to create great turgor pressures that force the cells through the material. This leads to a decrease in mechanical stability and offers a way for water to enter the polymeric material [70, 95]. The latter may increase the electrical conductivity of an insulating material.
2.6.5 Color and odor Many microorganisms produce pigments. These pigments are often lipophilic and therefore tend to diffuse into the matrix of a polymeric material. The stains produced are impossible to remove by simple cleaning [70, 78]. In addition, metabolites from biodegradation are sometimes sources of odour. A small concentration of a substance can be enough to cause problems [80]. However, this problem is of an aesthetic nature and does not affect the insulating properties of the silicone rubber.
2.7 PREVENTION OF MICROBIOLOGICAL GROWTH
2.7.1 Biocides Active substances that eliminate microorganisms or inhibit their reproduction are denoted biocides. Numerous additives of this kind exist on the market, and it is a demanding task to choose a biocide able to protect a high voltage insulator from biological growth. It is important that the substance is compatible with the rubber and does not affect its properties. It is also necessary that the biocide effectively kills unwanted microorganisms, while leaving people and the environment unharmed. In addition, to be effective in an outdoor environment, inhabited by an enormous variety of microorganisms, a biocide has to have a broad effectivity spectrum and offer small probability for microorganisms to develop resistance to the active substance [78, 80]. High voltage insulators are meant to function in an outdoor environment for many years with no need for service or replacement. This put demands on biocides that often have to be present on the surface of the silicon rubber in a certain minimum concentration to be effective. The active substance consequently has to be effective in low concentrations and have a low washout if it is required to be active over a long period of time [78]. It is important to take the washout effect into account when testing the effectiveness of a biocide. It has been shown that a biocide with a high initial activity can become inactivated after a period of outdoor storage. This may be due, for example, to washout or inadequate light stability [80]. It is quite common to use a biocide not as an additive to prevent growth but as a surface treatment to kill a mature biofilm. This is not to be recommended since the biocide kills the microorganisms, but it does not remove the dead biomass from the system. The accumulation of biodegradable organic material often give rise to a rapid microbial regrowth [71, 96].
![Page 22: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/22.jpg)
————— Introduction —————
12
2.7.2 Cleaning Cleaning an infected material removes dead biomass from the system and thus makes the surface less attractive for microorganisms. A rational cleaning often includes two steps, one where the physical stability of the biofilm is weakened and a second in which the biofilm is removed from the system. Oxidisers or detergents are useful for the first step, while flushing, brushing or similar physical techniques are useful for the second step. [71]. Tests performed on silicon rubber insulators shows that water repellent properties and other properties disturbed by the biofilm were partially restored after cleaning with alcohol and high pressure water [8].
2.7.3 Surface modification The hydrophobic nature of a silicone rubber contributes to its resistance to utilisation by microorganisms. Water and nutrients are essential for all kinds of biological growth and both are limited on a hydrophobic surface where water forms droplets that run off the material washing nutrients away [77]. In addition, the hydrophobicity substantially decreases the rate of hydrolysis and microbial attack of the polymer [82]. The low surface free energy of silicone rubber makes it useful in the production of non-stick coatings [97]. Silicone rubber is used in applications were biofouling cannot be avoided, such as in the coating of fishing nets. The weak adhesion between the adhering biofilm and the silicone-coated net facilitates cleaning [98]. Changing the microstructure of the rubber surface can further strengthen the non-stick characteristics of the silicone rubber. Micro-scale riblets or pyramids printed on to the surface of a silicone rubber sample may protect the material from biofouling [99, 100].
![Page 23: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/23.jpg)
————— Experimental —————
13
3 EXPERIMENTAL
3.1 MATERIALS
3.1.1 Silicones PDMS rubber base with 20% SiO2 filler and 0,52 % di(4-methyl benzoyl)peroxide added as crosslinker was mixed with Martinal OL-104 S vinylsilane surface treated aluminium trihydrate (ATH) and Firebrake 290 zinc borate delivered by Wacker Silicone as shown in table 3.1. Table 3.1 Type and amount of flame retardant added to the silicone rubber materials No: Material Flame retardant (pph*) Flame retardant %
1 Base No flame retardant added No flame retardant added 2 Base + ATH 100 pph ATH 50% ATH 3 Base + ATH + zinc borate 90 pph ATH + 10 pph zinc
borate 45% ATH + 5% zinc borate
4 Base + zinc borate 10 pph zinc borate 9% zinc borate 5 Commercial mix Unknown Unknown
*Parts per hundred resin Materials were kneaded at 12 rpm in a Brabender internal mixer for 15 min prior to curing. The curing was performed in a Schwabentan Polystat press for 10 min at a temperature of 180°C and a pressure of 10 MPa. The resulting discs had a diameter of 200 mm and a thickness of 2 mm. Samples were post-cured for 4 h in a hot air oven at 200°C before use. The commercial material was pressed and cured in accordance with instructions from the supplier. To study the degradation of PDMS mediated by enzymes or radicals more defined materials were needed. Silicone oil with a viscosity of 100 cSt and decamethyltetrasiloxane from Sigma Aldrich were used together with a platina catalysed PDMS rubber. The rubber was prepared by mixing vinyl terminated PDMS oil with crosslinker (6 % of methylhydro-dimethylsiloxane) and catalyst (35 ppm of a platinum divinyltetramethyldisiloxane complex).
![Page 24: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/24.jpg)
————— Experimental —————
14
The curing was performed in a Pasadena Hydraulics Inc. 0230 press for 15 min at 135°C under a pressure of 2 MPa [101].
3.1.2 Insulators
Insulators infected by biological growth were collected from the Bagamoyo test station, Tanzania (tropical climate), the University of Peradeiya , Sri Lanka (tropical climate) and the Anneberg test station, Sweden (temperate climate). The insulators had been in service for several years and no information about the composition of the materials used for production of the housings was available. The worst infected parts of the insulators were analysed with ESEM/EDX before and after gentle cleaning with a soft cloth dampened with distilled water. Small pieces of rubber cut from the centre of the insulators were used as reference.
3.1.3 Microorganisms
Isolates Microorganisms were isolated from the studied insulators by inoculating different growth media with finely grained biofilm suspended in water. Algae were grown on BG 11, a medium designed for the isolation of green and blue-green algae, and Jaworski´s medium with added NaSiO3 for the isolation of green algae and diatoms [102]. Fungal growth was observed on potato dextrose agar and malt extract agar; i.e. two commonly used undefined media designed for the growth and isolation of fungi [103]. Isolation was than made from malt extract agar diluted to one tenth of the recommended concentration. This medium is poor in nutrients and thus resembles the natural habitat of the isolated fungi better than the nutrient-rich medium used for observation. Hyphal tips, colonies or spores were selected for isolation. 50 fungal cultures and 20 algae cultures from each biofilm were isolated. Each fungal culture was subcultured three times on malt extract agar and algae were subcultured three times on BG 11 (as agar and in liquid dilution series). All isolates were visually examined and studied under a light microscope to roughly determine their class. The three most common fungal species isolated from each biofilm were sent to Centraalbureau voor Schimmelcultures, the Netherlands, for identification, while algae cultures were submitted to the Department of Agricultural Microbiology, Agricultural University of Wroclaw, Poland. Standard test organisms The molds prescribed in standard tests and the molds used in the degradation studies performed are listed in Tab. 3.2. All microorganisms were grown and kept in accordance with instructions given by the supplier.
![Page 25: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/25.jpg)
————— Experimental —————
15
Table 3.2 Fungal strains used in standard tests and degradation studies Fungal specie Supplier Aspergillus niger DSMZ – Strain DSM 1957 Aspergillus terreus DSMZ – Strain DSM 1958 Aureobasidium pullulans DSMZ – Strain DSM 2404 Chaetomium globosum DSMZ – Strain DSM 1962 Paecilomyces variotii DSMZ – Strain DSM 1961 Penicillium funiculosum DSMZ – Strain DSM 1944 Scopulariopsis brevicaulis DSMZ – Strain DSM 9122 Trichoderma virens DSMZ – Strain DSM 1963 Phanerochaete chrysosporium DSMZ – Strain DSM 1556 Phanerochaete chrysosporium CBS – Strain CBS 481.73 Phanerochaete chrysosporium ATCC – Strain 34541
3.2 GROWTH TESTS The resistance of silicone rubber to biological growth was tested using standard test procedures in combination with new methods developed for this study. All the samples used were washed with 70% ethanol and dried in a sterile air-flow overnight before inoculation with microorganisms. Inoculation was mediated by spraying the surface of the samples with suspensions of microorganisms, at the same time controlles were inoculated with sterile medium. Unless otherwise stated, tests were performed in triplicate on circular samples with a diameter of 30 mm and a thickness of 2 mm. In most cases, the extent of biological growth was judged according to the scale in Tab. 3.3. Table 3.3 Scale for determining the extent of growth on the specimens.
0 No growth apparent under a nominal magnification of 60×
1 Growth not, or hardly visible to the naked eye, but clearly visible under the microscope
2 Growth plainly visible to the naked eye, but covering less than 25% of the test surface
3 Growth plainly visible to the naked eye and covering more than 25% of the test surface
4 Growth plainly visible to the naked eye and covering more than 50% of the test surface
A stereomicroscope with 20x ocular and 3x objective was used to evaluate the samples. In cases where the contrast between biological growth and sample surface was low, SEM was used for the evaluation.
![Page 26: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/26.jpg)
————— Experimental —————
16
3.2.1 Powder test, mold Zinc borate and ATH were mixed into malt extract agar in concentrations from 20 pph to 100 pph. The resulting agar was sprayed with suspensions of fungal spores in distilled water. Three different suspensions were prepared, one for each country studied, by pouring 15 ml of distilled water onto the surface of the fungal isolates. The wetted surface of each culture was scraped with a sterile platinum wire and the suspended spores were filtered through a thin layer of glass wool to an Erlenmeyer flask containing glass beads. Suspensions were shaken to break clusters of spores and mix the suspension. The resulting liquid was used for inoculation of samples. Samples were incubated in room temperature for 28 days prior to evaluation.
3.2.2 Powder test, algae Zinc borate and ATH were mixed into BG11 agar [102] in concentrations from 20 pph to 100 pph. The resulting agar was sprayed with suspensions of algae cells in BG11 liquid growth medium. Suspensions were prepared by pouring 15 ml of BG 11 onto the surface of the algae isolates. The wetted surfaces were scraped with a sterile platinum wire and the resulting liquid was used for inoculation of the samples. Samples were incubated at room temperature in a window for 28 days prior to evaluation.
3.2.3 IEC 68-2-10, mold The silicone rubber materials described in Tab. 3.1 were tested in accordance with the basic environmental testing procedure IEC 68-2-10, part 2, test J, mold growth. However, in some of the experiments, the microorganisms stipulated in the standard test were replaced by the fungal isolates. Two variations of the test were carried out; the first one specified inoculation of the specimen with a suspension of mold spores in distilled water, while the second variation specified inoculation with mold spores suspended in a nutrient solution. Samples were incubated for 84-days in 98% humidity at 28°C prior to evaluation.
3.2.4 ASTM G21-90, mold The silicone rubber materials described in Tab. 3.1 were tested in accordance with the ASTM G21-90 standard practice for determining the resistance of synthetic polymeric materials to fungi. However, in some of the experiments, the microorganisms stipulated in the standard test were replaced by the fungal isolates. Samples of virgin materials and materials aged with oxygen plasma were incubated for 84-days in 98% humidity at 28°C prior to evaluation.
3.2.5 ASTM D 5589-97, algae The silicone rubber materials described in Tab. 3.1 were tested in accordance with the ASTM D 5589-97 standard test method for determining the resistance of paint film and related coatings to algal defacement. The algal isolates were used as test organisms. Samples were incubated in room temperature under a fluorescent lamp with a cycle of 14 h light and 10 h darkness for 21-days at a relative humidity of ≥ 85% prior to evaluation.
![Page 27: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/27.jpg)
————— Experimental —————
17
3.2.6 Quick test, mold 10 ml of water was added to each of the following mold cultures: Aspergillus niger, Trichoderma virens, Chaetomium globosum, Penicillium funiculosum and Aureobasidium pullulans. The surfaces of the wetted cultures were scraped gently with a flame-sterilised platinum wire. The suspended spores were filtered through a thin layer of glass wool to an Erlenmeyer flask prepared with 20 solid glass beads. The mixture was then diluted with distilled water to a volume of 100 ml and the flask was shaken to mix the spores. Samples of the silicone rubber materials described in Tab. 3.1 were put on malt extract agar. Virgin materials as well as materials aged with oxygen plasma were tested. The mounted samples were sprayed with the mixed spore suspension and the containers were sealed to maintain a moist atmosphere. The sealed Petri discs were stored in room temperature for 28 days prior to evaluation.
3.2.7 Microenvironment chambers Discs of the materials described in Tab. 3.1 were cut into plates shaped as a quarter of a circle with a radius of 10 cm. Three plates of each material were hung in inclined positions using nylon thread. The lowest plate of each material was divided into two sections. One was mechanically aged with sandpaper; the other was aged with oxygen plasma just before inoculation with microorganisms. The assemblies of the five studied materials were placed in four closed microenvironment chambers as shown in Fig 3.1. Three chambers represented the studied countries respectively. The fourth was used as a reference chamber with negative control specimens. All chambers were maintained at a temperature of approximately 25°C and a relative humidity of ≥85%. A daylight lamp with a cycle of 12 h light and 12 h darkness was used to provide the UV radiation necessary for algae growth.
Figure 3.1 Schematic drawing of a microenvironment chamber. 30 day old mixed cultures, containing algae bacteria and fungi from the different biofilms, were harvested from BG11 agar by pouring 10 ml of BG11 liquid broth onto the agar surface and gently scraping the microorganisms with a sterile platinum wire. Plates were inoculated
1
2
3
4
5
6
7
8 1. Base + zinc borate 2. Base + ATH + zinc borate 3. Base 4. Commercial mix 5. Base + ATH 6. Water, about 5 cm deep 7. Thermometer/Hygrometer 8. Tyburski, Euro-Light, LT15W/010 daylight lamp
![Page 28: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/28.jpg)
————— Experimental —————
18
with a solution of microorganisms from the specific country by spraying. All specimens were reinoculated with microorganisms suspended in BG 11 once a week during the first five months of the experiment, to create a self-sustaining biofilm; thereafter samples were reinoculated once every month to support the growing biofilm. Reference samples were sprayed with sterile BG11 liquid broth. Samples were photographed and evaluated by image analysis and laser-induced fluorescence after 6 months of incubation. After one year, the effects of the biofilms on the materials tested were studied using ESEM/EDS and IR. At the same time, the hydrophobicity of the second sample in each assembly of materials were evaluated in accordance with instructions given in STRI Guide 8, were the drop pattern formed after wetting of a surface is studied in order to assess surface hydrophobicity [104, 105]. Hydrophobicity was recorded before and after gentle cleaning of the tested surface with a cloth damped with distilled water.
3.3 LASER-INDUCED FLUORESCENCE In order to study the effect of mold growth on the laser-induced fluorescence of different silicone rubber materials a series of samples, listed in Tab. 3.4, was prepared by spraying the materials described in Tab. 3.1 with suspensions of mold spores. Fungal spore suspensions were prepared by pouring 20 ml of IEC 68-2-10 fungal nutrient medium on the agar surface of each of the fungal isolates. The surfaces of the wetted cultures were scraped gently with a flame-sterilised platinum wire. The resulting suspensions were filtered through thin layers of glass wool to Erlenmeyer flasks prepared with 30 ml of IEC 68-2-10 nutrient medium and 10 solid glass beads. The flasks were shaken and the suspensions were sprayed onto the silicone rubber samples. All samples were incubated for 45 days at 27°C and 95% relative humidity before measurements were conducted. Table 3.4 Samples grown for laser-induced fluorescence analysis
Materials tested Fungal strain used 1 2 3 4 Epicoccum nigrum x Microsphaeriopsis x Cladosporium cladosporioides x x x x Fusarium semitectum x Polyscytalum fecundissimum x Stagonospora x Curvularia lunata x Cladosporium tenuissimum x Clean materials x x x x
A laser generating radiation in pulses (3 ns, ~15 Hz, ~1 µJ) at a wavelength of 337 nm was used to study samples from the microenvironment chamber as well as the samples listed in
![Page 29: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/29.jpg)
————— Experimental —————
19
Tab. 3.4. Each spectrum was accumulated from 100 laser pulses and 20 spectra were collected from each sample. The laser light was guided via a telescope through a fused silica optical fibre, 600 µm in diameter, to the sample under investigation. The tip of the fibre was placed about 1 mm above the sample. The laser-induced fluorescence was spatially emitted in all directions and a fraction of it was collected by the same fibre and guided back to an optical multi-channel analyser system. The resolution of the system, set by the 100 µm slit width, was 2.2 nm, and the spectrum could be recorded up to 805 nm. A detailed description of the system can be found in Ref. [106]. Data obtained from the analysis were pre-processed by mean normalisation and mean centring in order to produce a fluorescence spectrum representing the sample. In some cases, this spectrum was simplified using principal component analysis (PCA) that projects the large data set of the spectra analysed into a smaller set of data that is easier to overview. The first principal component (PC1) is the combination of variables that explains the greatest amount of variation between spectra. The second PC (PC2) describes the second greatest amount of variation orthogonal to the first PC and so on. Higher order PCs correspond to small variances and can be seen as noise [107].
3.4 IMAGE ANALYSIS Samples were laid flat on a blue background and photographed using a standard Canon IXUS V3 digital colour camera. The image analysis was than performed in six steps using Matlab.
1. In the first step, the background was separated from the sample. This was done by determining differences in colour between sample and background. First, each image was represented as a set of three matrices, containing intensity values of the red, green and blue components, respectively. The blue component was then divided by the sum of the three colour components. The quotient of this operation differs between sample and background; hence the sample can be separated from the background through intensity thresholding [108]. The result of this operation is a black and white image of the sample alone.
2. In the second step, the possible influence of shading at the sample edge was removed by erosion of the image by a circular element, removing object pixels at its boundaries.
3. The third step produced a colour image of the sample from the black and white image obtained in the two first steps by multiplication of this image by the original colour image.
4. The fourth step compensated for illumination variations by dividing the sample into a set of sub-images in which the maximum values are identified and used to calibrate the remaining operations.
5. The fifth step separated biological growth from silicone rubber. Again, the blue component of the image was used for segmentation of the sample into covered and non-covered areas by means of intensity thresholding [109]. Blue was selected since
![Page 30: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/30.jpg)
————— Experimental —————
20
the contrast between the rubber and the biofilm was highest in this component. The resulting black and white image separates regions of growth from clean regions
6. Finally, the covered area was calculated by counting the numbers of pixels classified as growth. To avoid the need for calibration, the covered area was always related to the area classified as sample surface.
3.5 DEGRADATION STUDIES In order to decide whether the chemical bonds of the PDMS molecule can be affected by biologically mediated processes, an unfilled PDMS rubber, PDMS oil and a DMS oligomer were treated with lignin-degrading enzymes or radicals produced through the Fenton mechanism. In each case 0,020 g of the sample was weighed into a 100 ml Erlenmeyer flask where the reaction was performed. Samples and reference samples were set in triplicates. After treatment, PDMS rubber was removed from the reaction vessel and studied with SEM and IR. Oils and oligomers were extracted to chloroform according to the following procedure.
1. The content of the Erlenmeyer flask was filtered through a finely meshed strainer into a separation funnel, and solid matter caught by the mesh was returned to the Erlenmeyer flask.
2. 10 ml of chloroform was then added to the separation funnel and the funnel was manually agitated for 5 min.
3. After 5 min equilibration the chloroform phase was emptied into the Erlenmeyer flask.
4. Steps two and three were then repeated with fresh chloroform. 5. Finally, the Erlenmeyer flask was treated in an ultrasonic bath for 10 min.
After extraction PDMS oil was analysed using SEC and GC/FID, while PDMS oligomers were analysed with GC/FID only.
3.5.1 Enzymatic degradation According to United States Patent No 6,020,148, the lignin-degrading fungus Phanerochaete chrysosporium is capable of degrading the siloxane bond of PDMS [94]. The growth medium prescribed in the patent is known to promote the formation of peroxidases [110]. The test described was repeated twice, using fungal strains from DSMZ and CBS respectively, in order to study the degradation process. In addition, the trial was repeated a third time using an optimised growth medium and an ATCC strain of Phanerochaete chrysosporium [111, 112]. Optimised growth medium was prepared by dissolving 0.1 g (NH4)2SO4, 20 g glucose, 1,0 g KH2PO4, 0,2 g NaHPO4, 0,5 g MgSO4*7H2O, 0,017 g MnSO4*H2O, 10 µg ZnSO4*7H2O, 20 µg CuSO4*5H2O, 100µg CaCl2, 100 µg FeSO4*7H2O and 5 µg thiamine in 50 mM Malonate
![Page 31: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/31.jpg)
————— Experimental —————
21
buffer spiked with 0,1% Tween 80. The pH was adjusted to 4,5 before the addition of fungal spores. Samples were incubated as stationary cultures in 20 ml liquid growth medium at 30°C for a period of 60 days before extraction and analysis.
3.5.2 Degradation by Fenton mechanism When hydrogen peroxide and Fe2+ react, OH• radicals are formed through Fenton mechanism. These radicals may be able to degrade the chemical bonds of PDMS [113]. A simple Fenton reaction was performed as follows: 10 ml of a 10 mmol/L solution of FeSO4*7H20 was added to each sample. Reaction was then initiated by drop wise addition of 10 ml of a 1 mol/L solution of H2O2. The reaction was completed at room temperature overnight before extraction and analysis.
3.6 INSTRUMENTATION
3.6.1 Oxygen plasma ageing Oxygen plasma aging was performed in a V15-G microwave frequency reactor from Plasma-Finish GmbH, operated at 2.45 GHz and 100 W for 180 s at an oxygen pressure of 28 Pa and a gas flow of 50 ml/min.
3.6.2 Light microscopy A Leitz Ortholux II POL-BK optical microscope was used to study the biofilms and the isolated microorganisms.
3.6.3 SEM A Jeol JSM-5400 Scanning Electron Microscope was used at an acceleration-voltage of 10 kV. Samples were dried in vacuum at room temperature overnight and sputtered with palladium/gold before analysis.
3.6.4 ESEM/EDS An XL TMP (W) Environmental Scanning Electron Microscope from FEI/Philips was used in the low vacuum mode at an acceleration voltage of 10 kV. Microanalysis for determination of atomic composition in the surface layer was carried out with an EDS-system from EDAX.
3.6.5 IR Infrared spectra were recorded on a Perkin Elmer Spectrum 2000 FTIR equipped with a golden gate normal single reflection ATR accessory. Infrared absorption was recorded from 600 to 4000 cm-1.
![Page 32: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/32.jpg)
————— Experimental —————
22
3.6.6 GC/FID A Varian 3400 Gas Chromatograph equipped with a flame ionisation detector and a CP8752 column, 30 m x 0,32 mm, film thickness 0,25 µm, from Varian was used. The column temperature was raised from 40°C to 250°C at a rate of 10°C/min. The injector was used in split mode at 250°C, while the detector was operated at 275°C.
3.6.7 SEC A 510 Size Exclusion Chromatograph from Waters equipped with three PLgel 10µm mixed-B columns, 300x7,5 mm, from Polymer Labs was used at room temperature and a flow rate of 1 ml/min. Spectra were recorded with a PL-ELS 1000 evaporative light scattering detector.
![Page 33: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/33.jpg)
————— Results and discussion —————
23
4 RESULTS AND DISCUSSION
4.1 COMPOSITION OF BIOFILMS Biofilms are complex structures in which a multitude of microorganisms from different biological classes may coexist, compete or co-operate. The composition of the biofilm affects its interaction with the support material [70]. Therefore it is important to know the composition of the biofilm colonising the surface of interest, in this case silicone rubber insulators. In this work, three different biofilms, collected from silicone rubber insulators exposed to the outdoor environment in Sweden, Sri Lanka and Tanzania, have been analysed. Filamentous fungi and micro algae in association with bacteria were isolated from the biofilms under study. Even though the insulators were collected from three different continents, the compositions of the biofilms studied were remarkably similar. Small unicellular green algae of the Chlorella family, living in symbiosis with bacteria, dominated the biofilms and traces of filamentous fungi were spread through the algae matrix. The similarity between the different biofilms indicates that the mechanism of biofouling of silicone rubber insulators is the same all over the world. The identified species, listed in Tab. 4.1, were therefore used to test the resistance of several silicone rubber formulations to biological growth. Table 4.1 Microorganisms used for inoculation of silicone rubber samples. Country Fungi Algae
Epicoccum nigrum Microsphaeriopsis1
Chlorella saccharophila +6 bacterial strains Sweden
Cladosporium cladosporioides Fusarium semitectum Polyscytalum fecundissimum
Chlorella vulgaris var. Autotrophica Sri Lanka
Stagonospora2 +5 bacterial strains Curvularia lunata Tanzania Cladosporium tenuissimum
Chlorella vulgaris var. Autotrophica +2 bacterial strains
1 Not possible to identify on species level. 2 This anamorph has not been given a formal name.
![Page 34: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/34.jpg)
————— Results and discussion —————
24
4.2 EFFECT OF ADDITIVES Not all insulators in the field are affected by biological growth, indicating that some formulations are protected. In an attempt to identify the source of the observed differences in sensitivity, it was decided to analyse some of the materials used. The investigation was soon focused on the effect of the flame-retardants. A series of tests, designed to determine the sensitivity of a polymeric material and its additives to microbiological growth, was developed and used to evaluate the effect of zinc borate and alumina trihydrate (ATH) on biological growth. Results of the tests were evaluated according to the scale given in Tab. 3.3, in which 0 denotes a clean surface and 4 a surface covered to more than 50 % by biological growth.
4.2.1 Powder tests Tests with flame-retardants, zinc borate and ATH, as powder mixed in growth medium were performed in order to study the immediate influence of these chemicals on microbiological growth. As can be seen in Tab. 4.2, mold growth was not hindered on any of the samples containing ATH. Zinc borate on the other hand seems to have a preventive effect on the growth of mold, as can be seen in Tab. 4.3. The extent of growth on samples with added zinc borate is dependent on the concentration of additive as well as on the types of microorganisms tested. It seems that while molds from Tanzania is very sensitive to the toxic effects of zinc borate, molds from Sri Lanka and Sweden are able to tolerate higher concentrations of the substance. Table 4.2 Extent of mold growth on 3 samples for each concentration of ATH.
Sweden Sri Lanka Tanzania Concentration of ATH (pph) 1 2 3 1 2 3 1 2 3
20 4 4 4 4 4 4 4 4 4 40 4 4 4 4 4 4 4 4 4 60 4 4 4 4 4 4 4 4 4 80 4 4 4 4 4 4 4 4 4 100 4 4 4 4 4 4 4 4 4
Table 4.3 Extent of mold growth on 3 samples for each concentration of zinc borate.
Sweden Sri Lanka Tanzania Concentration of zinc borate (pph) 1 2 3 1 2 3 1 2 3
20 3 3 3 3 3 3 0 0 0 40 3 3 3 2 2 2 0 0 0 60 3 3 3 1 1 1 0 0 0 80 2 2 2 0 0 0 0 0 0 100 2 2 2 0 0 0 0 0 0
![Page 35: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/35.jpg)
————— Results and discussion —————
25
Further testing showed that zinc borate powder could prevent algal growth as well as mold growth. As can be seen in Tab. 4.4, the addition of ATH to the algae culture medium did not affect the growth of algae. On the other hand, addition of zinc borate inhibited algal growth as shown in Tab. 4.5. The living algae cells sprayed on the surface of the agar could not reproduce when zinc borate was added to the medium. When the concentration of zinc borate was high, all the algae cells died and lost their green colour. Table 4.4 Extent of algae growth on 3 samples for each concentration of ATH.
Sweden Sri Lanka Tanzania Concentration of ATH (pph) 1 2 3 1 2 3 1 2 3
20 4 4 4 4 4 4 4 4 4 60 4 4 4 4 4 4 4 4 4 100 4 4 4 4 4 4 4 4 4
Table 4.5 Extent of algae growth on 3 samples for each concentration of zinc borate.
Sweden Sri Lanka Tanzania Concentration of zinc borate (pph) 1 2 3 1 2 3 1 2 3
20 2 2 2 0 0 0 2 2 2 60 0 0 0 0 0 0 0 0 0 100 0 0 0 0 0 0 0 0 0
The powder tests developed for this study are fast and easy to use. A clear trend was observed already one week after incubation, and after 28 days it could definitely be concluded that zinc borate is toxic to the microorganisms tested, while ATH is not. However, for some of the species, a very high concentration of zinc borate was needed to effectively hinder growth. This should not be interpreted as meaning that zinc borate is not effective as a growth suppressor in silicone rubber materials. Growth conditions are very poor on the surface of a silicone rubber material compared to those in the agar used in the powder tests, where nutrients are abundant.
4.2.2 Tests of silicone rubbers The difference in growth conditions between powder tests and tests performed on polymeric materials was clearly shown when silicone rubber materials containing ATH or zinc borate were evaluated. The silicone rubber formulations described in Tab. 3.1 were subjected to a series of tests to determine their resistance to biological growth. Two variations of the standard procedure IEC 68-2-10, designed for the determination of the resistance of a material to mold growth, were used in the present work; one in which nutrients that support mold growth were added to the silicone rubbers together with the spores and one in which the specimens were inoculated with nothing but mold spores and water. In the latter case, the fungi must use the supporting rubber as the single source of nutrient for growth.
![Page 36: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/36.jpg)
————— Results and discussion —————
26
Tests were carried out with standard test organisms and with organisms isolated from the insulators studied in this work. Results of the tests are shown in Tab. 4.6 and Tab. 4.7. Table 4.6 IEC 68-2-10 Extent of mold growth on silicone rubber treated with spores and nutrients. Sweden Sri Lanka Tanzania Standard Material 1 2 1 2 3 3 1 2 3 1 2 3 Base 3 3 3 1 1 1 2 2 2 3 3 3 Base + ATH 3 3 3 1 1 1 3 3 3 3 3 3 Base + ATH + ZnBO3 3 3 3 0 0 0 2 2 2 3 3 3 Base + ZnBO3 2 2 2 0 0 0 2 2 2 3 3 3 Commercial mix 3 3 3 2 2 2 3 3 3 3 3 3 Table 4.7 IEC 68-2-10 Extent of mold growth on silicone rubber treated with spores and water. Sweden Sri Lanka Tanzania Standard Material 1 2 1 2 3 3 1 2 3 1 2 3 Base 1 0 0 0 0 0 0 0 0 0 0 0 Base + ATH 0 0 0 0 0 0 1 1 1 0 1 0 Base + ATH + ZnBO3 0 0 0 0 0 0 0 0 0 0 0 0 Base + ZnBO3 0 0 0 0 0 0 0 0 0 0 0 0 Commercial mix 2 1 1 1 1 1 2 2 2 2 2 2 The results of these standard tests show clearly that, if no nutrients are added to the samples, none of the silicone rubber materials mixed in the laboratory support growth. However, the commercial silicone rubber mix supports mold growth. These results strongly suggest that some component or combination of components in the commercial mix promotes the ability of the material to support mold growth. When nutrients were added to the silicone rubbers, most of the samples supported mold growth. In an out-door environment, nutrients from the surroundings may adhere to the surface of a silicone rubber insulator and provide nutrients for growth of a biofilm. However, growth is less severe on samples with zinc borate added. The low concentration of flame retardant used in the materials is sufficient to partially protect the silicone rubber from mold growth. This could not be predicted from the powder tests. The sensitivity of the fungal species to the addition of zinc borate also differs between the standard tests and the powder tests. The fungal cultures from Tanzania seemed very sensitive when powders were tested, but standard tests show that, when these molds are grown on silicone rubber materials, they can tolerate higher concentrations of zinc borate. Instead, fungal cultures from Sri Lanka, that were easy to grow on the agar used in the powder test, were very hard to grow on silicone rubber and impossible to grow when zinc borate was added to the rubber. Nevertheless, both types of tests show clearly that the sensitivity to zinc borate differs between different fungal species. This emphasises that care is needed in the
![Page 37: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/37.jpg)
————— Results and discussion —————
27
selection of test organisms. If possible, species likely to infect the material under normal service conditions should be chosen. On the other hand, valuable information can also be gained from standard tests performed as recommended. Microorganisms recommended in standard test procedures are chosen for their ability to negatively affect the tested materials, and they can therefore be said to represent a worst-case scenario. In this work, the advantages of using standard test organisms was shown when samples were subjected to the ASTM G21-90 standard for determining the resistance of synthetic polymeric materials to fungi. Samples were treated with mold spores and nutrient salts, but no source of carbon was added to the solution. If the spores were to germinate, they would thus have to use the test material as the source of carbon. The results of the test, when performed with organisms isolated from the insulators studied, are shown in Tab. 4.8 and they resemble the results of the IEC 68-2-10 standard tests. Table 4.8 ASTM G 21-90 Extent of mold growth on silicone rubber treated with spores and salt. Sweden Sri Lanka Tanzania Material 1 2 3 1 2 3 1 2 3 Base 0 0 0 0 0 0 0 0 0 Base + ATH 0 0 0 0 0 0 0 0 0 Base + ATH + zinc borate 0 0 0 0 0 0 0 0 0 Base + zinc borate 0 0 0 0 0 0 0 0 0 Commercial mix 2 2 2 1 0 0 3 3 3 However, when the test was carried out with the organisms stipulated in the standard, more information was gained. In Fig. 4.1, results from the unmodified ASTM standard test are shown together with results from a new test method called the Quick Test. In this method, growth was initiated and well established on highly nutritive agar before it started to colonise the sample. The fact that a material is easily colonised may be important, not for the initiation but for the advance of biological growth. Both tests were performed on virgin material as well as on materials aged with oxygen plasma prior to inoculation with microorganisms.
0
0,5
1
1,5
2
2,5
Base Base+ATH Base+ATH+Zn Base+Zn Commercial
Ext
ent o
f gro
wth
ASTM unagedASTM agedQuick unagedQuick aged
Figure 4.1 Results from the Quick Test and the ASTM G21-90 standard test when performed using the microorganisms stipulated in the standard. Tests were performed in triplicates and results were evaluated according to the scale described in Tab 3.3. The average of this evaluation is plotted.
![Page 38: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/38.jpg)
————— Results and discussion —————
28
The results obtained again indicate that the commercial silicone rubber is the most sensitive material, while the silicone rubber formulations with added zinc borate seem to be more protected. However, when the very potent fungal species stipulated in the standard test were used, the extent of growth varied among the materials tested. Apart from the fact that zinc borate protects the samples; the results indicate that ATH promotes growth to some extent. This could bee due to the surface treatment of the ATH particles, the vinylsilanes used contain carbon that may provide a source of nutrients for microorganisms. However, for the degree of colonisation measured in the Quick Test, the surface roughening caused by the addition of ATH-filler is probably more significant. A rough surface offers better support for an advancing growth than a smooth material. Results from the Quick test also indicate a difference between virgin materials and materials aged with oxygen plasma. Growth advanced faster and further on the aged samples when compared to unaged rubber of the same type. This is probably due to the partially hydrophilic nature of the plasma treated rubbers. The wetted surface formed by the treatment provided water and support to the advancing mold-growth. The sensitivity to algae growth of the silicone materials under investigation was tested according to the procedure described in the ASTM D 5589-97 standard practice. Algae use CO2 as source of carbon through photosynthesis, therefore no source of carbon was added to the growth medium used in these experiments. The results shown in Tab. 4.9 indicate that zinc borate is toxic to the studied algae. Growth was not affected on pure silicone, the mix with ATH or the commercial mix, but algal growth was hindered or inhibited on materials with added zinc borate. This can be very important for the performance of the materials when they are used outdoors. Algae growth is not expected to degrade its support material directly; but in an outdoor environment mixed biofilms are formed. Algae growth may attract other kinds of microorganisms that can use the colonised material as a carbon source. Table 4.9 ASTM D 5589-97 Extent of algal growth on silicone rubber treated with algal cells. Sweden Sri Lanka Tanzania Material 1 2 3 1 2 3 1 2 3 Base 2 2 2 2 2 2 2 2 2 Base + ATH 2 2 2 2 2 2 2 2 2 Base + ATH + zinc borate 1 1 1 2 2 2 1 1 1 Base + zinc borate 0 0 0 0 0 0 0 0 0 Commercial mix 2 2 2 2 2 2 2 2 2
4.3 DETERMINATION OF BIOFOULING In order to simulate biofilm growth on high voltage insulators in an outdoor environment, microenvironment chambers were prepared. In these chambers, mixed biofilms resembling those formed on insulators in field use were grown on the silicone rubber materials. Algae cells immediately started to grow on materials not containing zinc borate. After several
![Page 39: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/39.jpg)
————— Results and discussion —————
29
weeks, fungal growth started to develop on the materials infected by algae growth, and biofilms similar to those formed on insulators in the field were formed. The zinc borate-filled materials where algae refused to grow seemed protected from fungal growth as well. Microorganisms in a biofilm tend to live in symbiosis. It is known that the algae used in this study often grow in association with bacteria, and it seems probable that the fungal species isolated from the studied biofilms need algae as source of nutrients for growth [114-116]. This means that the protective effect of zinc borate against algal growth also strengthens the protection against mold growth. Materials incubated in the microenvironment chambers were not used only to study the resistance of the silicone rubbers to the formation of a biofilm. ESEM/EDX and IR analysis were performed on the materials in order to detect changes in chemical composition of the sample surfaces, while image analysis and laser-induced fluorescence spectroscopy were used to study the development of the biological growth.
4.3.1 Image analysis Manual inspection is the most commonly used way to estimate the area covered by biological growth. However, the method is operator-dependent and therefore suffers from a lack of precision. Samples from the microenvironment chambers were therefore subjected to image analysis in an attempt to determine the covered area more precisely. Six months after inoculation, samples were photographed and the resulting digital images were subjected to image analysis in order to determine the extent of growth on the different materials. This was done by segmentation of the photographs into regions of similar chromatic appearance. A typical result obtained through the application of this segmentation technique is shown in Fig 4.2, where regions classified as growth have been marked in red. As can be seen, the highlighted regions correspond well to the areas covered by growth.
Figure 4.2 A typical result obtained through image analysis. a) Photograph of an ATH-filled silicone rubber sample infected by a biofilm from Tanzania. b) Regions identified as growth by using image analysis are marked in red.
a) b)
![Page 40: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/40.jpg)
————— Results and discussion —————
30
As can be seen in Fig. 4.3, the image analysis results clearly show that the flame-retardant zinc borate hinders the development of the biofilm, and that ATH has no hindering effect on the growth. In fact, results again indicate that ATH might even support the biofilm. Another effect observed was that the biofilm originating from Sri Lanka developed faster on the commercial material tested, than on the other two biofilms under study. This might be due to the composition of the biofilm. Microscopic studies showed that the biofilm from Sri Lanka contained a larger proportion of fungi than the biofilms isolated from either Tanzania or Sweden. The commercial rubber was, as the previous discussion shows, sensitive to fungal growth.
Effect of filler
0,0
2,0
4,0
6,0
8,0
10,0
12,0
14,0
Base ATH ATH+Zn Zn Com
Cov
ered
are
a (%
)
SriTzSwe
Effect of UV-light
0,0
2,0
4,0
6,0
8,0
10,0
12,0
14,0
Base ATH ATH+Zn Zn ComC
over
ed a
rea
(%)
lowmediumhigh
Figure 4.3 The effect of material composition on the extent of biological growth.
Figure 4.4 The effect of UV-light exposure on the extent of biological growth.
Another observation was that direct UV exposure from a daylight lamp effectively hindered the growth of the biofilm. Fig. 4.4 shows that the samples that were nearest to the daylight lamp in the microenvironment chambers were almost completely free from growth. On the middle plates that were partly shaded growth developed much better. This effect can also be seen at high voltage insulators in service, where growth develop quicker on the shaded parts of the insulators [1, 5, 13]. The plates that were close to the bottom of the environmental chambers should, according to theory, be the worst infected samples, since they were partly shaded and hydrophilic [72]. However, this was not supported by results. This discrepancy is probably due to the method of inoculation. In an outdoor environment, microorganisms are deposited on the silicone rubber by wind and rain, whereas in the microenvironment chambers, microorganisms are sprayed onto the silicone rubber samples, and droplets form on the surface of the material. On the hydrophilic samples, these droplets pool together, form wetted traces, and run off the plate.
4.3.2 Laser-induced fluorescence
Recent studies indicate that image analysis can be used to estimate the area and distribution of growth on both material samples and complete insulators [65]. Nevertheless, the technique
![Page 41: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/41.jpg)
————— Results and discussion —————
31
has its drawbacks. For instance, the method does not discriminate between biological growth and other coloured pollutants on the insulator surface. To overcome this problem, and possibly increase the sensitivity compared to photography, laser-induced fluorescence (LIF) spectroscopy was explored as a tool for the detection of growth. In LIF surface spectroscopy, the material under study is irradiated with monochromatic light from a laser source. Molecules in the sample surface absorb photons and electrons become excited. Fluorescent light is emitted and detected when the electrons spontaneously return to their ground state. The intensity of the fluorescent light is often substantially higher from a clean surfaces than from a surface covered by biological growth [66]. However, the absolute intensity is dependent on several factors, such as laser pulse energy, area of excited region, and the angle between the surface under study and the laser beam. Thus, the absolute intensity does not provide unambiguous information about the samples. A more promising approach is to use the spectral shape of the normalised fluorescence spectrum. The fluorescence spectrum from a fungi-covered silicone rubber is often wider than the spectrum from a clean sample and, if algae are present on the surface, an additional peak at about 685 nm indicates chlorophyll fluorescence [69]. These effects were clearly seen when samples from the microenvironment chambers were studied. The broadening effect and the algae peak were more pronounced on silicone rubbers with a severe biofilm growth than on cleaner samples. The algae peak disappeared completely on samples with zinc borate added, as can be seen in Fig. 4.5.
450 500 550 600 650 700 750 8000
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5x 10-3
Inte
nsity
, [ar
b. u
nits
]
Wavelength [nm]450 500 550 600 650 700 750 800
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
x 10-3
Inte
nsity
, [ar
b. u
nits
]
Wavelength [nm]
Figure 4.5 Results from LIF-surface spectroscopy. a) Spectra collected from the ATH-filled silicone rubber. The red spectrum obtained from a sample infected by a dense biofilm is wider than the corresponding blue reference spectrum and the algae peak at 685 nm is clearly visible. b) Spectra from the zinc borate-filled rubber. The sample looked clean to the naked eye, since no mature biofilm had formed. The red spectrum obtained from the sample infected with microorganisms is only slightly broader than the blue reference spectra and there is no peak corresponding to chlorophyll fluorescence. In addition, LIF surface spectroscopy was found to be a very sensitive method for the detection of microorganisms; areas that looked clean to the naked eye sometimes gave a response as if they were contaminated. When these areas were studied under the microscope it
a) b)
![Page 42: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/42.jpg)
————— Results and discussion —————
32
was found that traces of biological growth were in fact present. This indicates that LIF surface spectroscopy may be used to detect microbiological attack on silicone rubber insulators before a mature biofilm visible to the naked eye has formed. However, the method has its drawbacks. While it is easy to detect algae defacement of a silicone rubber surface, detection of fungal growth is more problematic. The observed broadening of the LIF-spectra is not always easy to detect from the full spectrum obtained. A simplified score plot based on the variations between spectra is easier to handle and it can, if there are significant differences between samples, separate clean samples and samples infected by fungal growth into distinctly different classes. Fig 4.6 a) shows typical fluorescence spectra of eight different fungal cultures grown on silicone rubber filled with ATH. Spectra obtained from the fungus-covered samples are wider than the spectrum of the clean ATH-filled silicone rubber material used as reference. However, for some samples these effects were small and difficult to detect in the spectra obtained. Results are easier to interpret from a simplified score plot of the sample set. In Fig. 4.6 b) spectra obtained from the infected materials are showed and compared to spectra from clean material in a simplified score plot. Each spectrum is reduced to a single dot in the score plot. Dots originating from spectra of samples infected by fungal growth are spread out to the left in the score plot, when compared with the encircled dots from the clean material. The spread is due to the combination of fluorescence from the fungal growth and the material. A heavily contaminated sample ends up further to the left in the score plot compared to a cleaner sample. When results are displayed as a simplified score plot it is easy to differentiate between a samples infected by fungal growth and a clean material. The different fungal cultures studied all followed the same trend in the simplified score plot. In addition, further studies showed that the method gave the same general response when other silicone rubber materials were tested. This is desirable for the development of a general inspection technique for composite insulators.
400 500 600 7000
1
2
3
4
Wavelength (nm)
Inte
nsity
(arb
. uni
ts)
-10 -5 0 5-5
0
5
PC 1
PC 2
Fig. 4.6. Fluorescence spectra of eight fungal cultures grown on silicone rubber with added ATH a) Full fluorescence spectra of the sample set. b) Simplified score plot of the studied samples;. results from the clean ATH-filled silicone rubber material are located within the circle, while spectra from materials infected with fungal growth are spread out to the left in the plot.
a) b)
![Page 43: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/43.jpg)
————— Results and discussion —————
33
When a silicone rubber sample infected by biological growth is subjected to a combination of LIF surface spectroscopy and image analysis, this gives a more complete picture of the situation than either method can give on its own. While LIF surface spectroscopy can be used to decide the type of contaminant and reveal information of contaminants invisible to the naked eye, image analysis can be used to estimate the severity of the growth. Both methods have a potential for use as in-service diagnostic techniques. However, by utilizing LIF for creating images depicting certain spectral properties, so-called imaging measurements, a combination of LIF and digital image analysis can be obtained, which is probably even more interesting for future applications. A mobile and self-contained light detection and ranging systems that could be used for field measurements of this kind already exists [117].
4.3.3 Hydrophobicity One of the reasons why silicone rubber materials are preferred to ceramics in high voltage insulators is the hydrophobicity of the silicone rubber surface, but when a biofilm covers the insulator surface, the hydrophobicity of the rubber is disturbed [3, 6, 7] The most common way to measure surface hydrophobicity is by water contact angle measurements. However, this is not practical when the effect of a biofilm on surface hydrophobicity is to be recorded. In most cases, the biofilm is unevenly distributed over the sample surface, making it difficult to choose representative spots for the measurement. A biofilm may also function as a sponge withdrawing the water drop used for the contact angle measurement. To avoid these problems, the hydrophobicity of the silicone materials incubated in the microenvironment chambers were tested in accordance with the STRI hydrophobicity classification guide [104]. In this method the pattern formed by the drops when a large surface area is sprayed with water is studied and compared to a series of seven reference images with different hydrophobicity classes (HC). HC 1 denotes a very hydrophobic sample on which only discrete droplets are formed, while HC 7 describes a hydrophilic sample on which a continuous water film is formed over the whole tested area. The method has a potential for use on insulators in the field; and the results can be evaluated either by visual inspection or by use of image analysis [62]. The worst infected samples from the microenvironment chambers were classified according to the STRI-hydrophobicity classification guide. The results, displayed in Tab. 4.10, clearly show that samples covered with microorganisms were more hydrophilic than virgin materials and reference materials treated with nutrient salt solution. However, after cleaning the surface of the infected materials with a soft cloth damped with distilled water, the hydrophobicity of the materials were somewhat restored. However, materials containing large amounts of filler particles were not as easy to restore as were less filled materials. Filler particles cause surface roughening and it seemed that the gentle cleaning procedure applied was not effective enough to completely remove the biofilm from the rough surface of the filled materials.
![Page 44: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/44.jpg)
————— Results and discussion —————
34
Table 4.10 HC of silicone rubber infected by biofilms and reference materials Samples from microenvironment chambers Contaminated Cleaned Material Sri Tz Sw Ref Sri Tz Sw Ref
Virgin materials
Base 3 3 3 2 1 1 1 1 1 Base + ATH 4 4 4 2 2 2 2 1 1 Base + ATH + zinc borate 3 3 3 2 2 2 2 1 1 Base + zinc borate 2 2 2 2 1 1 1 1 1 Commercial mix 3 3 3 2 2 2 2 1 1
4.3.4 ESEM/EDX If a severe growth has developed on an active silicone rubber insulator, it may be necessary to remove the biofilm. Spraying with a biocide is not a good alternative; this may kill the microorganisms but it does not remove them from the insulators. Dead biomass is left in the system and this opens the way for a rapid microbiological re-growth [71]. If insulators are to be treated in some way, cleaning is a better alternative. However, cleaning is only effective if the adhesion between the biofilm and the silicone rubber is not too strong. To examine the possibility of cleaning an infected silicone rubber insulator, samples from real insulators as well as samples from microenvironment chambers were analysed by using an environmental scanning electron microscope (ESEM) with X-ray energy dispersive spectroscopy (EDS). ESEM/EDS not only give a microscopic picture of the infected surface but also combine this information with an overview of the elemental composition of the surface of the tested material. Since the molecules in the biofilm differ in chemical composition from those of the supporting silicone rubber, the atomic composition of the surface layer can be used to monitor the amount of contaminants before and after a washing procedure. If traces of the biofilm remain after cleaning the surface, it can be assumed that the adhesion between the biofilm and its support is too strong to allow the applied washing procedure to be effective. Silicone rubber samples cut from insulators situated in Tanzania, Sri Lanka and Sweden were analysed with ESEM/EDS. The results shown in Fig 4.7 and Fig 4.8 indicate that it was possible to clean the African insulator efficiently by gently wiping the surface with a soft clot wetted with distilled water, but that the Asian rubber was not that easy to clean from biofouling. Traces of Mg, Na and Fe originating from the biofilm were detected after the cleaning. ESEM pictures supported the results of the elemental analysis; the silicone rubber from Sri Lanka showed a rough surface after cleaning, while the rubber surface from Tanzania looked clean and smooth. The results of ESEM/EDS analysis of the Swedish insulator resembled those of the insulator from Sri Lanka.
![Page 45: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/45.jpg)
————— Results and discussion —————
35
Fig 4.7 ESEM/EDS of insulator from Tanzania It was possible to restore the surface of the silicone rubber by the gentle cleaning procedure applied. After cleaning, ESEM images show a smooth surface and EDX does not show traces of molecules originating from the biofilm.
a) EDS of virgin SIR
b) EDS of SIR covered by growth c) ESEM of SIR covered by growth
d) EDS of SIR after cleaning e) ESEM of SIR after cleaning
Si
Si
Si
C
C
C
O
O
O
Na Mg
Al
Al
S
![Page 46: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/46.jpg)
————— Results and discussion —————
36
Fig 4.8 ESEM/EDS of insulator from Sri Lanka It was not possible to restore the surface of the silicone rubber by the gentle cleaning procedure applied. After cleaning, traces of Mg Na and Fe originating from the biofilm were detected by EDS and ESEM showed a rough surface.
a) EDS of virgin SIR
b) EDS of SIR covered by growth c) ESEM of SIR covered by growth
d) EDS of SIR after cleaning e) ESEM of SIR after cleaning
Al
Al
Al
Si
Si
Si
O
O
O
C
C
C
Fe
Fe
Na
Na
Mg
Mg
![Page 47: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/47.jpg)
————— Results and discussion —————
37
Unlike the Tanzanian insulator, EDS analysis showed that the insulators from Sri Lanka and Sweden contained large amounts of the flame retardant ATH. It seems that an ATH-filled silicone rubber is more difficult to clean, than a rubber containing less filler. In order to verify this hypothesis, samples from the microenvironment chambers were analysed with ESEM/EDS. After one year of incubation in the microenvironment chamber representing Sri Lanka, small samples covered with a dense biofilm were cut from ATH-filled silicone rubber and Base rubber. These samples were analysed before and after cleaning. Results verified that it was easy to remove the biofilm from the Base rubber, but the ATH-filled material was more difficult to clean. This is probably due to the fact that the ATH-filled rubber had a rougher surface structure than the Base material. A rough surface is more accessible for microbiological growth [72].
4.4 BIODEGRADATION OF THE PDMS MOLECULE
Despite the fact that an ATH-filled silicone rubber is difficult to clean from biological growth, no evidence was found that the biofilms examined in this study are able to degrade the silicone rubber matrix. When samples from the microenvironment chambers were cleaned from biological growth and analysed with infrared (IR) spectroscopy, no difference in spectra could be observed between samples treated with microorganisms and virgin materials. This indicates that no chemical bonds had been disrupted by the influence of the biofilm. The PDMS molecule is known to be very stable and no biological process is known that produces or degrades covalent bonds in organosilicones [46]. Nevertheless, silicone rubber could still be degraded by biological processes through secondary mechanisms. Many microorganisms secrete powerful enzymes with the ability to degrade very stable polymeric structures. Among these, the white rot fungi hold a unique position. This class of molds has evolved non-specific mechanisms for degrading the complex polymeric structure of lignin. The enzyme system responsible for the degradation includes peroxidases that promote the reduction of peroxides to free radicals [90, 93]. These radicals have been shown to attack stable polymeric materials such as polyvinyl chloride, nylon and polyethylene [118-120]. Claims have been made that these molds could also degrade PDMS oils [94]. According to United States patent No: 6,020,184, silicone oils of high molecular weight could be degraded by the lignin-degrading fungus Phanerochaete chrysosporium. The fungus is grown for 60 days in a liquid medium spiked with a small amount of silicone oil. According to the results reported this procedure degrades 17-50 % of the added silicone oil. However, we have repeated the experiment, as described in the patent, and after modifications recommended by experts in the field of lignin degradation. Still, no reliable proof of PDMS degradation has been observed in any of the tests performed. In order to study the biologically mediated degradation of the silicone molecule in detail, tests were performed on a PDMS rubber, on a PDMS oil of high molecular weight, and on a DMS oligomer. After treatment with the lignin-degrading fungus Phanerochaete chrysosporium,
![Page 48: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/48.jpg)
————— Results and discussion —————
38
oils were analysed by SEC in order to detect main-chain scissoring reactions, oils and oligomers were analysed with GC/FID in order to observe degradation mediated by chain end or side chain mechanisms, and rubbers were analysed for chemical changes in the surface layer by use of IR. No significant difference in surface composition of the rubber or the molecular weight of the oil was observed and no low molecular weight degradation products were found in the GC analysis performed after treatment of the siloxane materials with the lignin-degrading fungus. It was therefore decided that experiments with radicals generated by chemical mechanisms should be performed as a compliment to the biodegradation study. The materials mentioned above were exposed to hydroxyl radicals generated by the Fenton mechanism. However, subsequent analysis showed no significant influence of the hydroxyl radicals on the silicone materials analysed. Some results from the performed tests can be seen in fig. 4.9-4.11
Figure 4.9 No degradation of the silicone rubber could be observed through IR-spectroscopy. No covalent bonds in the sample surfaces had been disrupted by the treatment with enzymes or radicals
Figure 4.10 The results from SEC analysis showed no degradation of the PDMS oil. The molecular weight of the oil was the same after exposure to enzymes or radicals
Enzymes
Radicals
Reference
Enzymes
Radicals
Reference
Min
![Page 49: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/49.jpg)
————— Results and discussion —————
39
Figure 4.11 The results from the GC analysis showed no degradation of the DMS oligomer No new peaks denoting degradation products could be observed in the chromatograms The results obtained from the degradation study indicate that the PDMS molecule is very stable against biodegradation. However, it cannot be concluded, based on these results only, that PDMS is a biologically inert material. It is possible that degradation could occur if a more effective experimental design were developed. If, for example, the silicone oil could be dispersed or dissolved in the reaction medium, the PDMS molecules would be more accessible to degrading enzymes and radicals. Even so, the probability that the silicone rubber matrix of a high voltage insulator could be degraded by the direct influence of microorganisms is very small.
Enzymes
Radicals
Reference
Min
Min
Min
![Page 50: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/50.jpg)
————— Results and discussion —————
40
![Page 51: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/51.jpg)
————— Conclusions —————
41
5 CONCLUSIONS
Subsequent effects ranging from fouling to degradation of the polymer matrix occurs when a polymeric material is colonised by a biofilm. For silicone rubbers in high voltage insulators this study showed that fouling is the most severe problem. The polydimethylsiloxane (PDMS) molecule is highly stable and no evidence of biodegradation has been found. Neither microorganisms isolated from insulators in service nor aggressive ligninolytic fungal species seemed to be able to break the chemical bonds of PDMS. Biofouling can, however, seriously influence the function of an insulator. This study showed that the hydrophobicity of a silicone rubber is reduced when the material is colonised by a biofilm. This can alter the electrical properties of a fouled insulator. It is therefore important to develop methods for the identification of infected units. In this work, laser-induced fluorescence (LIF) spectroscopy was successfully used to identify biological contamination on silicone rubber surfaces. Photography followed by image analysis was then used to estimate the extent of growth. The surface hydrophobicity of the silicone rubber can be restored by removing the attached biofilm. The effectiveness of a cleaning procedure depends, however, on the composition of the rubber. A silicone rubber containing large amounts of alumina trihydrate (ATH) has a rougher surface structure, compared to an unmodified silicone. This makes it difficult to remove an attached biofilm in an effective way. In addition, surface treated ATH makes a material more accessible to microorganisms. This was shown when different silicone rubber formulations were subjected to a series of microbiological growth tests developed for this study. Methods useful for fast evaluation of samples were used together with standard test methods and microenvironment chambers constructed for long-term studies in a simulated outdoor environment. These tests showed that while the commercial silicone rubber tested supported growth, addition of the flame-retardant zinc borate to a material made it able to suppress the growth of mold, algae and mixed biofilms.
![Page 52: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/52.jpg)
————— Conclusions —————
42
![Page 53: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/53.jpg)
————— Future work —————
43
6 FUTURE WORK
It has been shown in a series of growth tests that addition of zinc borate to silicone rubber protects the material from severe biofouling. However it would be advantageous if materials could be tested outdoors under true service conditions. The methods developed to study the biodegradation of PDMS should be perfected in order to definitely confirm or exclude the degradation of PDMS under the influence of enzymes or radicals. In this work laser-induced fluorescence (LIF) spectroscopy has been successfully used to identify silicone rubbers infected by biological growth. However the causes of the observed differences between clean and fouled materials are not yet fully understood. It would be beneficial for the future development of the technique if the biological structures responsible for the observed differences in fluorescence could be identified. Finally, methods combining LIF-spectroscopy and image analysis should be developed further and used to identify contaminated insulators in the field. One promising attempt in this direction is the mobile light detection and ranging (LIDAR) system used by Dernfalk et al for detection of biological growth on silicone rubber insulators. This method has the potential to be used to diagnose energised insulators from a safe distance [66].
![Page 54: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/54.jpg)
————— Future work —————
44
![Page 55: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/55.jpg)
————— Acknowledgements —————
45
7 ACKNOWLEDGEMENTS
My heartfelt thanks to Sigbritt Karlsson for accepting me as her PhD-student, thank you for supporting me throughout my studies. Further I would like to thank the members of the reference group; Stanislaw Gubanski, Bärbel Hahn-Hägerdal, Ulf Gedde, Håkan Wiek, Fredrik Sahlén and Sven Jansson for their interest in my research. My sincere gratitude also goes to the leaders and administrators of the department of fibre and polymer technology. ABB Corporate Research, Energimyndigheten and Elforsk are acknowledged for financial support through the Elektra programme. My fellow PhD-students Andreas Dernfalk at CTH and Magnus Begtsson at LTH are acknowledged for interesting and fruitful collaboration. Warm thanks also to Palle Ander and Maria del Pilar Castillo at SLU for invaluable advice in the field of lignin degradation. To my colleagues, you were always the best part of the job. Thanks to all of you, especially former and present members of the SK-research group, Nadja, Walker, Guillaume, Ana, Fran, Jonas, Emma, Åsa and Sara Some of you deserve special thanks for being true life savers; Jovan (San Diego and MSN), Calle (comics and philosophy), Mattias (champagne and psychology), Tahani (my first student), Karin (extractions and gossip), Johan (cars and sick humour), Emma (Västerås and hot discussions) and Peter (fun food delivery). Thanks also to the coffee-room people, Clara, Annika, Jonas, Jonas, David, Anders, Bruska, Bengt, Mari, Daniel, Alessandro, the Spanish league and those of you I have forgotten to mention. I will miss you all. Love to all my friends not kept in institution, especially to Jocke (breakfast soon?), Anna (the wedding planner) and Jenz, Tobias and Lina, (cats!), Maja, Fredrik and Maria (Stayokay) Micke (Byrådirektör Toll). Love also to Josefin (with family!), Elin and Josefin, your friendship means a lot to me, as does ”kvinnokampssemestrarna”. Still, my warmest gratitude goes to my family. You have never pushed me, always helped me and never stopped loving me. I feel safe knowing that you will always be there for me. To Anders, for the rest of our days.
![Page 56: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/56.jpg)
————— Acknowledgements —————
46
![Page 57: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/57.jpg)
————— References —————
47
8 REFERENCES
1. Naito, K., Matsuoka, R., and Sakanishi, K., Investigation of the insulation performance of the insulator covered with lichen. IEEE Transaction on Power delivery, 1990. 5(3): p. 1634-1640.
2. Fernando, M.A.R.M., Performance of Non-ceramic Insulators in Tropical Environments, in Department of Electric Power Engineering. 1999, Chalmers University of Technology: Göteborg. p. 140.
3. Fernando, M.A.R.M. and Gubanski, S.M., Performance of Nonceramic Insulators Under Tropical Field Conditions. IEEE Trans. on Power Delivery, 2000. 15(1): p. 255-360.
4. Gubanski, S.M., Swedish University Tests Composite Insulators in Tropical Environments, in Insulator News & Market Report. 1998. p. 56-61.
5. Gubanski, S.M., Fernando, M.A.R.M., Pietr, S.J., Matula, J., and Kyaruzi, A. Effects of Biological Contamination on Insulator Performance. in The 6th International Conference on Properties and Applications of Dielectric Materials. 2000. Xi'an, China.
6. Gubanski, S.M., Dernfalk, A.D., and Fernando, M.A.R.M. Performance of different insulator designs in tropical environments and diagnostic possibilities. in Cigré International Symposium on "Behaviour of Electrical Equipment and Components in Tropical Environments". 2001. Cairns, Australia.
7. Gorur, R.S., Montesinos, J., Robertson, R., Burnham, J., and Hill, R. Mold growth on nonceramic insulators and its impact on electrical performance. in IEEE Transmission and Distribution Conference. 1998. New Orleans, USA.
8. Hetherington, W., Experience with Non-Ceranic Bushings at Florida-Based Utility. News & Market Report, 1997(Nov/Dec): p. 31-35.
9. Gorur, R.S. and Bernstein, B.S., Field and laboratory aging of polymeric distribution cable terminations: part 1 - field aging. IEEE Transaction on Power Delivery, 1998. 13(2): p. 316-322.
10. Rackliffe, G.B., Lee, R.E., Fritz, D.E., and Harmon, R.W., Performance Evaluation of 15-KV Polymeric Insulators for Dead-End Type Applications on Distribution Systems. IEEE Transactions on Power Delivery, 1989. 4(2): p. 1223-1230.
![Page 58: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/58.jpg)
————— References —————
48
11. Gutman, I., Harting, R., and Vosloo, W.L. Field testing of composite insulators at natal test stations in south africa. in High Voltage Engineering Symposium. 1999. London, UK.
12. Fujii, O., Kondo, K., Kondo, T., Utsumi, Y., and Nakano, T. Investigation on contamination performance of polymer insulators deposited with algae. in XIIIth International Symposium on High Voltage Engineering. 2003. Netherlands: Millpress, Rotterdam.
13. Suzuki, A., Kumai, T., Shinoda, A., Hidaka, M., Kishida, R., Toshima, N., Koshino, Y., Sakanishi, K., and Utsumi, Y. Deterioration diagnosis technique of housing rubber for composite hollow insulators. in 7th International Conference on Properties and Applications of Dielectric Materials. 2003. Nagoya, Japan.
14. Kunde, K., Hennings, R., Kuhl, M., Schütz, A., Janssen, H., and Stietzel, U. New experience with composite insulators. in Proc. Cigré Session. 1998.
15. Cherney, E.A., Non-Ceramic Insulators - A Simple Design that Requires Careful Analysis. IEE Electrical Insulation Magazine, 1996. 12(3): p. 7-15.
16. Simmons, S., Shah, M., Mackevich, J., and Chang, R.J., Polymer Outdoor Insulating Materials. Part III-Silicone Elastomer Conciderations. IEE Electrical Insulation Magazine, 1997. 13(5): p. 25-32.
17. Owen, M.J. Surface Properties of Silicone High Voltage Insulators. in 4:th int. Conf. on Frontiers of Polymers and Adv. Mat. 1999. Hannover.
18. Kim, J., Chaudhury, M.K., and Owen, M.J., Hydrophobicity loss and recovery of silicone HV insulation. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 695-702.
19. Hillborg, H. and Gedde, U.W., Hydrophobicity Changes in Silicone Rubbers. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 703-717.
20. Kikuchi, T., Nishimura, S., Nagao, M., Izumi, K., Kubota, Y., and Sakata, M., Survey on the use of non-ceramic composite insulators. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 548-556.
21. 22.03, C.W.G. and de Tourreil, C., Worldwide service experience with HV composite insulators. Electra, 2000(191): p. 27-43.
22. Reynders, J.P., Jandrell, I.R., and Reynders, S.M., Review of Ageing and Recovery of Silicone Rubber Insulation for Outdoor Use. IEEE Trans. on Dielectrics and Electrical Insulation, 1999. 6(5): p. 620-631.
23. Gorur, R.S. and Orbeck, T., Surface Dielectric Behaviour of Polymeric Insulation under HV Outdoor Conditions. IEEE Transactions on Electrical Insulation, 1991. 26(5): p. 1064-1072.
24. Hackam, R., Outdoor HV composite polymeric insulators. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 557-585.
25. Yoshimura, N., Kumagai, S., and Nishimura, S., Electrical and environmental aging of silicone rubber used in outdoor insulation. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 632-650.
26. Phillips, A.J., Childs, D.J., and Schneider, H.M., Ageing of Non-Ceramic Insulators due to Corona from Water Drops. IEEE Trans. on Dielectrics and Electrical Insulation, 1999. 13(3): p. 1081-1089.
![Page 59: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/59.jpg)
————— References —————
49
27. Gubanski, S.M. and Vlastos, A.E., Wettability of naturally aged silicone and EPDM composite insulators. IEEE Transactions on Power Delivery, 1990. 5(3): p. 1527-35.
28. Hillborg, H. and Gedde, U.W., Hydrophobicity recovery of polydimethylsiloxane after exposure to corona discharges. Polymer, 1998. 39(10): p. 1991-1998.
29. Lopes, I.J.S., Jayaram, S.H., and Cherney, E.A., A method for detecting the transition from corona from water droplets to dry-band arcing on silicone rubber insulators. IEEE Transactions on Dielectrics and Electrical Insulation, 2002. 9(6): p. 964-971.
30. Karady, G.G., Shah, M., and Brown, R.L., Flashover mechanism of silicone rubber insulators used for outdoor insulation - I. IEEE Transactions on Power Delivery, 1995. 10(4): p. 1965-71.
31. Shah, M., Karady, G.G., and Brown, R.L., Flashover mechanism of silicone rubber insulators used for outdoor insulation - II. IEEE Transactions on Power Delivery, 1995. 10(4): p. 1972-8.
32. Kim, S.-H., Temperature distribution in RTV silicone rubber coating following dry band arcing. IEEE Int. Symp. on Electrical Insulation, 1994: p. 599-602.
33. Ehsani, M., Borsi, H., Gockenbach, E., Morshedian, J., and Bakhshandeh, G.R., An investigation of dynamic mechanical, thermal, and electrical properties of housing materials for outdoor polymeric insulators. European Polymer Journal, 2004. 40(11): p. 2495-2503.
34. Janssen, H., Seifert, J.M., and Karner, H.C., Interfacial phenomena in composite high voltage insulation. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 651-659.
35. Virlogeux, F., Bianchini, D., Delor-Jestin, F., Baba, M., and Lacoste, J., Evaluation of cross-linking after accelerated photo-ageing of silicone rubber. Polymer International, 2004. 53(2): p. 163-168.
36. Soerqvist, T. and Vlastos, A.E., Outdoor polymeric insulators long-term exposed to HVDC. IEEE Transactions on Power Delivery, 1997. 12(2): p. 1041-1048.
37. Gustavsson, T.G., Gubanski, S.M., and Lambrecht, J., Hydratization of the PDMS Backbone during Water Immersion Test. Annual Report - Conference on Electrical Insulation and Dielectric Phenomena, 1998. 1: p. 269-272.
38. Koo, J.Y., Kim, I.T., Kim, J.T., and Park, W.K., An experimental investigation on the degradation characteristic of the outdoor silicone rubber insulator due to sulfate and nitrate ions. Annual Report - Conference on Electrical Insulation and Dielectric Phenomena, 1997(Vol. 2): p. 370-373.
39. Han, S.-I., Yoon, J.-Y., Park, K.-S., and Han, S.-O., Surface degradation of silicone rubber under accelerated aging condition. Annual Report - Conference on Electrical Insulation and Dielectric Phenomena, 1997(Vol. 2): p. 439-443.
40. Wang, X., Kumagai, S., and Yoshimura, N., Contamination performances of silicone rubber insulator subjected to acid rain. IEEE Transactions on Dielectrics and Electrical Insulation, 1998. 5(6): p. 909-916.
41. Griessbach, E.F.C. and Lehmann, R.G., Degradation of polydimethylsiloxane fluids in the environment - a review. Chemosphere, 1999. 38(6): p. 1461-1468.
42. Stevens, C., Environmental degradation pathways for the breakdown of polydimethylsiloxanes. Journal of Inorganic Biochemistry, 1998(69): p. 203-207.
![Page 60: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/60.jpg)
————— References —————
50
43. Lehmann, R.G., Miller, J.R., and Collins, H.P., Microbial degradation of dimethylsilanediol in soil. Water, Air, and Soil Pollution, 1998. 106(1-2): p. 111-122.
44. Lehmann, R.G., Miller, J.R., Xu, S., Singh, U.B., and Reece, C.F., Degradation of Silicone Polymer at Different Soil Moistures. Environmental Science and Technology, 1998. 32(9): p. 1260-1264.
45. Lehmann, R.G., Miller, J.R., and Kozerski, G.E., Degradation of silicone polymer in a field soil under natural conditions. Chemosphere, 2000. 41(5): p. 743-749.
46. Graiver, D., Farminer, K.W., and Narayan, R., A Review of the Fate and Effects of Silicones in the Environment. Journal of Polymers and the Environment, 2003. 11(4): p. 129-136.
47. Hall, j.F., History and Bibliography of Polymeric Insulators for Outdoor Applications. IEEE Transaction on Power delivery, 1993. 8(1): p. 376-385.
48. Sebo, S.A. and Zhao, T., Utilization of fog chambers for non-ceramic outdoor insulator evaluation. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 676-687.
49. Williams, D.L., Haddad, A., Rowlands, A.R., Young, H.M., and Waters, R.T., Formation and Characterization of Dry Bands in Clean Fog on Polluted Insulators. IEEE Trans. on Dielectrics and Electrical Insulation, 1999. 6(5): p. 724731.
50. Gubanski, Experience with the Merry-go-round Test. IEE Transaction on Electrical Insulation, 1990. 25(2): p. 331-340.
51. Xu, G., McGrath, P.B., and Burns, C.W. Surface Degradation of polymer Insulators under accelerated Climatic Aging in Weather-Ometer. in IEEE International Symposium on Electrical Insulation. 1996. Montreal, Quebec, Canada.
52. Gustavsson, T.G., Gubanski, S.M., Hillborg, H., Karlsson, S., and Gedde, U.W., Ageing of Silicone Rubber under ac or dc Voltages in a Costal Environment. IEEE Transactions on Dielectrics and Electrical Insulation, 2001. 8(6): p. 1029-1039.
53. Sorqvist, T. and Gubanski, S.M., Leakage current and flashover of field-aged polymeric insulators. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 744-753.
54. Birtwhistle, D., Blackmore, P., Krivda, A., Cash, G., and George, G., Monitoring the condition of insulator shed materials in overhead distribution networks. IEEE Transactions on Dielectrics and Electrical Insulation, 1999. 6(5): p. 612-619.
55. Gubanski, S.M., Properties of silicone rubber housings and coatings. IEEE Transactions on Electrical Insulation, 1992. 27(2): p. 374-82.
56. Andersson, L.H.U. and Hjertberg, T., Silicone elastomers for electronic applications. I. Analyses of the noncrosslinked fractions. Journal of Applied Polymer Science, 2003. 88(8): p. 2073-2081.
57. Hillborg, H., Karlsson, S., and Gedde, U.W., Characterization of low molar mass siloxanes extracted from crosslinked polydimethylsiloxanes exposed to corona discharges. Polymer, 2001. 42(21): p. 8883-8889.
58. Karlsson, A. and Albertsson, A.-C., New Selective Method for Quantification of Organosilanol Groups in Silicone Pre-elastomers. Biomacromolecules, 2002. 3(4): p. 850-856.
59. Tourreil, C. Status of Inspection Techniques to Assess the Conditions of Non-Ceramic Insulators In Service. in Insulator World Congress 2000. 2000.
![Page 61: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/61.jpg)
————— References —————
51
60. Spangenberg, E. and Riquel, G. In service diagnostic of composite insulators EDF's test results. in 10th International Symposium on High Voltage Engineering. 1997. Montréal, Québec, Canada.
61. 22.03, C.W.G. and de Tourreil, C., Review of "in service diagnostic testing" of composite insulators. Electra, 1996(169): p. 105-119.
62. Berg, M., Thottappillil, R., and Scuka, V., Hydrophobicity estimation of high voltage polymeric insulating materials. Development of a digital image processing method. IEEE Transactions on Dielectrics and Electrical Insulation, 2001. 8(6): p. 1098-1107.
63. Dernfalk, A., Estimation of severity of growth on high voltage insulators. Machine Vision and Applications.
64. Dernfalk, A. and Gubanski, S.M. Use of digital image analysis for studying biological contamination on nonceramic insulators. in 12th International Symposium on High Voltage Engineering. 2001. Bangalore, India.
65. Dernfalk, A.D. and Gubanski, S.M. Techniques for estimation of biological contamination on insulators using image analysis. in submitted to IEEE Conference on Electrical Insulation and Dielectric Phenomena (CEIDP'04). 2004. Boulder, Colorado, USA.
66. Dernfalk, A.D., Bengtsson, M., Grönlund, R., Sjöholm, M., Weibring, P., Edner, H., Gubanski, S.M., Kröll, S., and Svanberg, S. Laser-induced fluorescence spectroscopy for detection of biological contamination on composite insulators. in Proc. International Symposium on High Voltage Engineering (ISH'03). 2003. Delft, Netherlands.
67. Larsson, A., Roslund, A., Dernfalk, A.D., and Gubanski, S.M. Remote and non-intrusive diagnostics of high-voltage insulation materials using laser-induced fluorescence spectroscopy. in IEEE Conference on Electrical Insulation and Dielectric Phenomena. 2001.
68. Larsson, A., Kröll, S., and Dernfalk, A. Laser-induced fluorescence surface spectroscopy - a candidate for the characterisation of high-voltage insulator surfaces. in 17th Nordic Insulation Symposium. 2001. Stockholm.
69. Larsson, A., Kröll, S., Dernfalk, A.D., and Gubanski, S.M., In-situ diagnostics of high-voltage insulation using laser-induced fluorescence spectroscopy. IEEE Trans. on Dielectrics and Electrical Insulation, 2002. 9(2): p. 274-281.
70. Flemming, H.-C., Relevance of biofilms for the biodeterioration of surfaces of polymeric materials. Polymer Degradation and Stability, 1997(59): p. 309-315.
71. Eckhardt, F.E.W., Microbial Diversity and Airborne Contamination, in Microbially Influenced Corrosion of Materials, E. Heitz, W. Sand, and H.-C. Flemming, Editors. 1996: Berlin.
72. Wimpenny, J., Manz, W., and Szewzyk, U., Heterogeneity in biofilms. FEMS Microbiology Reviews, 2000(24): p. 661-671.
73. Bos, R., van der Mei, H., and Busscher, H., Physico-chemistry of initial microbial adhesive interactions - its mechanisms and methods for study. FEMS Microbiology Reviews, 1999(23): p. 179-230.
74. Schmitt, J. and Flemming, H.-C., Water binding in Biofilms. Water Science and Technology, 1999. 39(7): p. 77-82.
![Page 62: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/62.jpg)
————— References —————
52
75. Flemming, H.-C. and Schaule, G., Biofouling, in Microbially Influenced Corrosion of Materials, E. Heitz, W. Sand, and H.-C. Flemming, Editors. 1996: Berlin. p. 39-54.
76. Habash, M.B., van der Mei, H.C., Reid, G., and Busscher, H.J., Adhesion of Pseudomonas aeruginosa to silicone rubber in a parallel plate flow chamber in the absence and presence of nutrient broth. Microbiology, 1997(143): p. 2569-2574.
77. Seal, K.J. and Morton, L.H.G., Chemical Materials, in Microbial Degradations, W. Schönborn, Editor. 1986, VCH: Düsseldorf. p. 583-606.
78. Wolf, A., Mould Fungus Growth on Sanitary Sealants. Construction Building Materials, 1989. 3(2): p. 145-151.
79. Pantke, M., General Aspects and Test Methods. Microbially Influenced Corrosion of Materials, cap. 26, p. 380-391., ed. E. Heitz, W. Sand, and H.-C. Flemming. 1996, Berlin.
80. Lorenz, J., Biostabilizers, in Plastics Additives, Gächer and Müller, Editors. 1989: Bensheim. p. 791-809.
81. Albertsson, A.-C. and Karlsson, S., Biodegradable polymers, in Environmental Analysis and Remidation, R. Meyers, Editor. 1998, John Wiley & Sons, Inc. p. 641-651.
82. Albertsson, A.-C. and Karlsson, S., Controlled Degradation by Artificial and Biological Processes, in Macromolecular Design of Polymeric Materials, K. Hatada, T. Kitayama, and O. Vogl, Editors. 1997, Marcel Dekker, Inc.: New Yourk, Basel, Hong Kong. p. 739-802.
83. Timmins, M.R. and Lenz, R.W., Enzymatic Biodegradation of Polymers: The polymer Chemists´Perspective. Trends in Polymer Science, 1994. 2(1): p. 15-19.
84. Williams, D.F., Interfacial reactions in the degradation of polymers by cells and bacteria. Biofouling, 1991. 4: p. 225-230.
85. Sand, W., Microbial Mechanisms of Deterioration of Inorganic Substrates - A General Mechanistic Overview. International Biodeterioration & Biodegradation, 1997. 40(2-4): p. 183-190.
86. Albertsson, A.C. and Karlsson, S., Chemistry and biochemistry of polymer biodegradation. Chem. Technol. Biodegrad. Polym., 1994: p. 7-17.
87. Rosciszewski, P., Lukasiak, J., Dorosz, A., Galinski, J., and Szponar, M., Biodegradation of polyorganosiloxanes. Macromolecular Symposia, 1998. 130: p. 337-346.
88. Neu, T.R., Van der Mei, H.C., and Busscher, H.J., Biodeterioration of medical-grade silicone rubber used for voice prostheses: a SEM study. Biomaterials, 1993. 14(6): p. 459-464.
89. Williams, D.F. and Zhong, S.p., Are Free Radicals Involved in Biodegradation of Implanted Polymers. Advanced Materials, 1991. 3(12): p. 623-625.
90. ten Have, R. and Teunissen, P.J.M., Oxidative mechanisms involved in lignin degradation by white-rot fungi. Chemical Reviews (Washington, D. C.), 2001. 101(11): p. 3397-3413.
91. Henriksson, G., Ander, P., Pettersson, B., and Pettersson, G., Cellobiose dehydrogenase (cellobiose oxidase) from Phanerochaete chrysosporium as a wood-
![Page 63: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/63.jpg)
————— References —————
53
degrading enzyme. Studies on cellulose, xylan and synthetic lignin. Applied Microbiology and Biotechnology, 1995. 42(5): p. 790-6.
92. Hilden, L., Johannson, G., Petterson, G., Li, J., Ljungquist, P., and Henriksson, G., Do the extracellular enzymes cellbiose dehydrogenase and manganese peroxidase form a pathway in lignin biodegradation? FEBS Letters, 2000(477): p. 79-83.
93. Hammel, K.E., Kapich, A.N., Jensen, K.A., and Ryan, Z.C., Reactive oxygen species as agents of wood decay by fungi. Enzyme and Microbial Technology, 2002. 30(4): p. 445-453.
94. Baud-Grasset, F. and Palla, J.-C., Polyorganosiloxane biodegradation method using a microscopic fungus and screening method, in PCT Int. Appl. 1996, (Rhone Poulenc Chimie, Fr.; Baud-Grasset, Frederic; Palla, Jean-Claude). Wo. p. 18 pp.
95. Bennett, J.W. and Faison, B.D., Use of Fungi in Biodegradation, in Man. Environ. Microbial., C.J. Hurst, Editor. 1997, ASM PRESS: Washington, D.C. p. 758-765.
96. Flemming, H.-C., Economical and Technical Owerview , cap. 1, p. 5-14. Microbially Influenced Corrosion of Materials, ed. E. Heitz, W. Sand, and H.-C. Flemming. 1996, Berlin.
97. Tsibouklis, J., Stone, M., Thorpe, A., Graham, P., Nevell, T., and Ewen, R., Inhibiting bacterial adhesion onto surfaces: the non-stick coating approach. International Journal of Adhesion & Adhesives, 2000(20): p. 91-96.
98. Hodson, S., Burke, C., and Bissett, A., Biofouling of fish-cage netting: the efficacy of a silicone coating and the effect of netting colour. Aquaculture, 1999(184): p. 277-290.
99. Petronis, S., Berntsson, K., Gold, J., and Gatenholm, P., Design and microstructuring of PDMS surfaces for improved marine biofouling resistance. Journal of Biomaterials Science, Polymer Edition, 2000. 11(10): p. 1051-1072.
100. Jelvestam, M., Edrud, S., Petronis, S., and Gatenholm, P., Biomimetic materials with tailored surface micro-architecture for prevention of marine biofouling. Surface and Interface Analysis, 2003. 35(2): p. 168-173.
101. Fateh-Alavi, K., Nunez, M.E., Karlsson, S., and Gedde, U.W., The effect of stabilizer concentration on the air-plasma-induced surface oxidation of crosslinked polydimethylsiloxane. Polymer Degradation and Stability, 2002. 78(1): p. 17-25.
102. Warren, A., Day, J.G., and Brown, S., Cultivation of algae and protozoa. Manual of Environmental Microbiology (2nd Edition), 2002: p. 71-83.
103. Tanner, R.S., Cultivation of bacteria and fungi. Manual of Environmental Microbiology (2nd Edition), 2002: p. 62-70.
104. STRI, Guide 1, 92/1: Hydrophobicity Classification Guide. 1992, www.stri.se. 105. STRI, Guide 8, 2002/1: Guidelines for inspection and analysis of silicone grease on
high voltage insulators. 2002, www.stri.se. 106. Klintberg, C., Andreasson, M., Sandström, O., Andersson-Engels, S., and Svanberg,
S., Compact System for Clinical Recordings of Laser-Induced Fluorescence Spectra. 2002, LOT-Oriel Italia.
107. Geladi, P., Chemometrics in spectroscopy. Part 1. Classical chemometrics. Spectrochimica Acta, Part B: Atomic Spectroscopy, 2003. 58B(5): p. 767-782.
108. Sonka, M., Hlavac, V., and Boyle, R., Image processing, analysis, and machine vision. 2nd ed. 1999: Brooks/Cole Publishing Company.
![Page 64: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/64.jpg)
————— References —————
54
109. Chowdhury, M.H. and Little, W.D., Image thresholding techniques, in Proc. IEEE Pacific Rim Conf. on Communications, Computers, and Signal Processing. 1995: Victoria, BC, Canada. p. 585-589.
110. Tien, M. and Kirk, T.K., Lignin Peroxidase of Phanerochaete chrysosporium, in Biomass, W. Wood and S. Kellogg, Editors. 1988, ACADEMIC PRESS, INC: San Diego. p. 238-249.
111. Costa-Ferreira, M., Ander, P., and Duarte, J.C. Formation of Peroxidases and Cellobiose: Quinone Oxidoreductase in Relation to Degradation of Syntetic Ligning by Phanerochaete chrysosporium. in 5th International Conference on Biotechnology in Pulp and Paper Industry. 1992. Tokyo, Japan.
112. Kirk, T.K., Schultz, E., Connors, W.J., Lorentz, L.F., and Zeikus, J.G., Influence of Culture Parameters on Lignin Metabolism by Phanerochaete chrysosporium. Archives of microbiology, 1987. 117: p. 277-285.
113. Teixeira, A.C.S.C., Guardani, R., and Nascimento, C.A.O., Photo-Fenton remediation of wastewaters containing silicones: Experimental study and neural network modeling. Chemical Engineering & Technology, 2004. 27(7): p. 800-810.
114. Zarnowski, R., Felske, A., Ellis, R.J., Geuns, J.M.C., and Pietr, S.J., A Methylobacterium-like organism from algal crusts covering silicone rubber electric insulators in Africa. Journal of applied microbiology, 2002. 93(6): p. 1012-1019.
115. Samson, R. and Enne de, B., Introduction to food-borne fungi. 5 ed, ed. R. Samson. 1996, Baarn: Centralbureau voor Schimmelcultures. 322.
116. Pitt, J. and Hocking, A., Fungi and food spoilage. 2 ed, ed. J. Pitt. 1997, London: Chapman & Hall. 593.
117. Weibring, P., Edner, H., and Svanberg, S., Versatile mobile lidar system for environmental monitoring. Applied Optics, 2003. 42(18): p. 3583-3594.
118. Deguchi, T., Kakezawa, M., and Nishida, T., Nylon biodegradation by lignin-degrading fungi. Applied and Environmental microbiology 1996. 63(1): p. 329-31.
119. Iiyoshi, Y., Tsutsumi, Y., and Nishida, T., Polyethylene degradation by lignin-degrading fungi and manganese peroxidase. Journal of Wood Science, 1998. 44(3): p. 222-229.
120. Kirbas, Z., Keskin, N., and Guner, A., Biodegradation of polyvinylchloride (PVC) by white rot fungi. Bulletin of Environmental Contamination and Toxicology, 1999. 63(3): p. 335-342.
![Page 65: BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ...7667/FULLTEXT01.pdf · BIOFILMS ON SILICONE RUBBER MATERIALS FOR OUTDOOR HIGH ... An electrical insulator in a high voltage](https://reader031.vdocument.in/reader031/viewer/2022030508/5ab731477f8b9a86428e7e74/html5/thumbnails/65.jpg)