boltpro linear, surface

Prudential Ltg. reserves the right to change design specifications or materials without notice. Please visit prulite.com for most current data. © 2015 All rights reserved – All products manufactured at: Prudential Ltg. 1774 E. 21st Street, Los Angeles, CA 90058

PRULITE.COM 213.746.0360

LED BoltPro | Linear, Surface

WARNING: Ground fixture in according with local and national electrical codes. Failure to do so may result in serious personal injury.

03-11-2021

I N S T A L L A T I O N I N S T R U C T I O N S

M O U N T I N G LO C AT I O N S

1. See row diagram or Prudential Ltg. layout plan (if provided). Begin all row mounting from left to right (see arrows).

2. Depending upon ceiling or wall construction reinforcement may be required at mounting locations.

3. Continuous row: Install one fixture section at a time.

4. Some field trimming of lenses may be required (see layout drawing).

5. We recommend using a chop saw with an 80 tooth blade for trimming lenses.

G E N E R A L N OT E SCROSS SECTION

Lens

Flash Suppression Device (FSD)

LED Tray

LED Tape

Flanged LED Tray Rotating Clip

Stem Mounting & 1/2˝ / 7/8˝ K.O. for Power Feed

Cable and Surface Mount

NOTE: 3˝ sensor cover can be installed at the center or end of fixture. Location must be specified at time of order.

11/4˝

Finish Plate 3/8˝ 3˝ Sensor Cover

2’ - 8’ to end of fixtures

8’ 8’8’7’ 9˝ Lens

8’

2˝

CABLE OR SURFACE MOUNTING WITH SENSOR COVER:

INDIVIDUAL FIXTURE:

L E N S R E M O VA L

1. Remove lens by pushing in sides and pulling one end of the lens away from the aluminum body.

Push in sides Pull one end of lens away from fixture





03-11-2021


C A B L E M O U N T I N G S U R FAC E M O U N T I N G

Mount cables to end plate brackets or joining brackets. Reference separate cable installation instructions.

Mount fixture to ceiling or wall.

CABLE PARTS (SHIPPED SEPARATELY)

SURFACE PARTS

Canopy KitBushing Gripper

Aircraft Cable

Dry Wall Screw (BY OTHERS)

L E D T R AY R E M O VA L

1. Unlock LED tray from clips and remove wires from LED drivers.

FINISH PLATE

ROTATING CLIP DETAIL

To lock and install tray, rotate clip by tightening screw (clockwise).

To unlock and remove tray, rotate clip by loosening screw (counter clockwise).





03-11-2021


E B C P — E L E C T R I C A L B OX CO V E R S ( O P T I O N A L )

Wall cutout to clear fixture mounting hole

Fixture mounting

hole

OPTIONAL ELECTRICAL BOX COVERS7/8˝ Dia. K.O. will accommodate 2˝x 4˝ or 4˝x 4˝ J-Box

J O I N I N G D E TA I L S ( O P T I O N A L )

F I N I S H I N G S T E P S

1. Follow joining detail instructions where fixtures are joined. FOR END OF ROWS INSTALL FINISH PLATES.

2. Use u-clips to Install flash suppression devices between lens joints.

FINISH PLATE

JOINING BRACKET

1. Make all wiring connections.

2. Re-install all LED trays. Ensure no wires are trapped between trays and clips and that they are tucked away to avoid shadows.

3. Install flash suppression device where there will be a lens seam.

4. Install/Re-Install all lenses.

FLASH SUPPRESSION DEVICE (SHIPPED SEPARATELY

EXCEPT IN CORNERS)

Joiner secured to housing with palnuts

(SUPPLIED)

Lens

FSD Holder

Wall cutout to clear fixture

mounting hole

Fixture mounting

hole

7/8˝ Dia. K.O. will accommodate 2˝x 4˝ or 4˝x 4˝ J-Box (by others)

Lorem ipsum

Lorem ipsum

1G: SINGLE GANG

2G: DUAL GANG

boltpro linear, surface

Documents