(bomba sellado sidd)ra91401_0705
TRANSCRIPT
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
1/28
Linear Motion andAssembly Technologies ServicePneumaticsHydraulics
Electric Drivesand Controls
Series 6Sizes Nominal pressure/Peak pressure5 4600/5100 psi (315/350 bar)10...200 5800/6500 psi (400/450 bar)250...1000 5100/5800 psi (350/400 bar)open circuits
Contents
Ordering Code / Standard Program 2...3
Technical Data 4...9
Ordering Code / Unit Dimensions, Size 5 10
Unit Dimensions, Sizes 10, 12, 16 11
Unit Dimensions, Sizes 23, 28, 32 12
Unit Dimensions, Size 45 13
Unit Dimensions, Sizes 56, 63 14
Unit Dimensions, Sizes 80, 90 15
Unit Dimensions, Sizes 107, 125 16
Unit Dimensions, Sizes 160, 180 17Unit Dimensions, Size 200 18
Unit Dimensions, Size 250 19
Unit Dimensions, Size 355 20
Unit Dimensions, Size 500 21
Unit Dimensions, Size 710 22
Unit Dimensions, Size 1000 23
Installation and Commissioning Notes 24
General Notes 28
Features
Fixed displacement pump AA2FO of axial piston, bent axisdesign, suitable for hydrostatic drives in open circuits
Use in mobile and industrial applications
Output flow is proportional to drive speed and displaceme
The drive shaft bearings are designed to give the service lifexpected in these areas of operation
High power density
Compact design
High overall efficiency
Cost effective concept
One piece pistons with piston rings
RA 91 401/07.05 1/28Replaces: 09.04Axial Piston
Fixed Displacment Pump AA2FO(A2FO)
Technical data sheet
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
2/28
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
3/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 3/28
O / 6 V01 02 03 04 05 06 07 08 09 10 11 12
Ordering Code / Standard Program (ordering code size 5 see page 10)
Shaft end 10 12 16 23 28 32 45 56 63 80 90 107 125 160 180 250
10
SAE Version(AA2F)
SAESplined shaft
S T
U
Q
Parallel keyed shaftDIN 6885
B
P
SAE parallel keyed shaft K
200 355 500 710 1000
ISO Version(A2F)
Splined shaftDIN 5480
A
Z
Parallel keyed shaft
DIN 6885
B
P
Mounting flange 10 12 16 23 28 32 45 56 63 80 90 107 125 160 180 250
11
SAE Version(AA2F)
2-bolt SAE C
4-bolt SAE D
DN
200 355 500 710 1000
ISO Version(A2F)
4-bolt ISO B
8-bolt ISO H
Service line ports
12
AA2F 1) 10 12 16 23 28 32 45 56 63 80 90 107 125 160 180 250
SAE flange ports A and B, at side andSAE flange port S, rear
55
Threaded ports A and B, at side andSAE flange port S, rear
56
A2F 2) 200 355 500 710 1000
SAE flange ports A and B, at side andSAE flange port S, rear
05
SAE flange ports A and B, rear andSAE flange port S, rear
11
1) threads of fastening screws and service lines are SAE (UN/UNF)2) threads of fastening screws are metric
= available = not available
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
4/28
4/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Hydraulic fluid
Before starting project planning, please refer to our datasheets RE 90220 (mineral oil), RE 90221 (environmentallyacceptable hydraulic fluids) and RE 90223 (HF hydraulicfluids) for detailed information regarding the choice of hydraulic
fluids and conditions of use.The AA2FO fixed displacement pump is not suitable for usewith HFA. If HFB, HFC and HFD or environmentally accep-table hydraulic fluids are being used, the limitation regardingtechnical data and seals mentioned in RE 90221 andRE 90223 must be observed. When ordering please indicatehydraulic fluid used.
Viscosity range
We recommend that a viscosity (at operating temperature) foroptimum efficiency and service life purposes of
opt = optimum viscosity 80...170 SUS (16...36 mm2/s)
selected, taken into consideration the tank temperature (opencircuits).
Limits of viscosity range
The following values apply in extreme cases:
Sizes 5...200:
min = 42 SUS (5 mm2/s)short term (t < 3 min) at max. permitted temperature oftmax = +240F (+115C).
max = 7400 SUS (1600 mm2/s),short term (t < 3 min) with cold start (p 435 psi / 30 bar,n 1000 rpm, tmin = -40F / -40C).
Sizes 250...1000:
min = 60 SUS (10 mm2/s),short term (t < 3 min) at max. permitted temperature oftmax = +195F (+90C)
max = 4600 SUS (1000 mm2/s),short term (t < 3 min) with cold start (p 435 psi / 30 bar,n 1000 rpm, tmin = -13F / -25C).
Note that the maximum hydraulic fluid temperature must not beexceeded locally either (e.g. bearing area). The temperature inthe bearing area is - depending on pressure and speed - up to22 F (12 K) higher than the average case drain temperature.
Special measures are necessary at temperatures between-40F and -13F (-40C and -25C). Please contact us.
See RE 90300-03-B for detailed information about operationat low temperatures.
Technical DataSelection diagram
VG22
VG32
VG46
VG68
VG100
opt.
80 (16)
170 (36)
(0) (20) (40) (60) (80) (100)(-40) (-20)
42 (5)
7400(1600)
viscosityS
US
(mm2/s)
fluid temperature range t in F (C)tmin= -40F(-40C)
tmax= +240F(+115C)
(-40) (-25) (-10) (0) (10) (30) (50) (70) (90) (115)
-40 -13 1200 20 40 60 80 160 195 240
(1600)(1000)
(600)(400)
(200)
(100)(60)
(40)
(20)
(10)
(5)
7000500030002000
1000
500300
150200
100
807060
50
40
Details regarding the choice of hydraulic fluid
To select the correct hydraulic fluid in open circuit applications,the temperature in the tank in relation to the ambient tempera-ture must be considered.
The hydraulic fluid should be selected so that within theoperating temperature range, the operating viscosity lies withinthe optimum range (opt) (see shaded section of the selectiondiagram). We recommend that the highest possible viscosityrange should be selected in each case.
Example: At an ambient temperature of XF (XC) an opera-ting temperature of 140F (60C) is set in the circuit. In the
optimum operating viscosity range (opt; shaded area) thiscorresponds to the viscosity classes VG 46 or VG 68; to beselected: VG 68.
Please note: The leakage fluid temperature, which is affectedby pressure and rotational speed, is always higher than the cir-cuit temperature or tank temperature. At no point in the systemmay the temperature be higher than 240F (115C) for sizes 5to 200 or 195F (90C) for sizes 250 to 1000.
If this cannot be achieved due to unusual operating parametersor high ambient temperatures, we recommend to apply bearingflushing at port U (sizes 250 ... 1000).
Filtration
The finer the filtration, the cleaner the fluid, the longer the ser-vice life of the axial piston unit.
To ensure proper function of the ax ial piston unit, the Hydraulicfluid must have a cleanliness level of at least
20/18/15 according to ISO 4406.
At very high hydraulic fluid temperatures (90C to max. 115C, notpermitted for sizes 250 to 1000), a cleanliness level of at least
19/17/14 according to ISO 4406 is required.
Please contact us if these cleanliness leveles cannot be achieved.
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
5/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 5/28
Technical DataOperational pressure range
Inlet
Minimum pressure at port S
The minimum inlet pressure depends on speed. The following limits must not be exceeded.
pabs min __________________________________ 12 psi (0.8 bar)
pabs max_________________________________ 435 psi (30 bar)
Outlet
Maximum pressure on port A or B (pressure data according to DIN 24312)
AA2F Sizes 10 12 16 23 28 32 45 56 63 80 90 107 125 160 180 250 Nominal pressure Peak pressure
Shaft end: S 5800 psi (400 bar) 6500 psi (450 bar)
S 5100 psi (350 bar) 5800 psi (400 bar)
Q 4350 psi (300 bar) 5100 psi (350 bar)
Q 4000 psi (280 bar) 4600 psi (315 bar)
T 5800 psi (400 bar) 6500 psi (450 bar)
U 5800 psi (400 bar) 6500 psi (450 bar)
B 5100 psi (350 bar) 5800 psi (400 bar)
P 5100 psi (350 bar) 5800 psi (400 bar)
K 5100 psi (350 bar) 5800 psi (400 bar)
A2F Sizes 5 200 355 500 710 1000 Nominal pressure Peak pressure
Shaft end: Z 5100 psi (350 bar) 5800 psi (400 bar)
A 5800 psi (400 bar) 6500 psi (450 bar)
P 5100 psi (350 bar) 5800 psi (400 bar)
B 5100 psi (350 bar) 5800 psi (400 bar)
B 3000 psi (210 bar) 3600 psi (250 bar)
C 4600 psi (315 bar) 5100 psi (350 bar)
With pulsating loads over pN = 4600 psi / 315 bar (pmax = 5100 psi / 350 bar);we recommend the use of a splined shaft (AA2FO 10...250: S, T or U / A2FO 200: A / A2FO 355...1000: Z)Attention: sizes 10 to 200: shaft end with drives of radial force loads at the drive shaft (pinion, V-belt drives) necessitate reductionof the nominal pressure to pN = 4600 psi (315 bar)! Sizes 250...1000 please contact us.
Minimum inlet pressure at suction port S with increased speed
In order to avoid damage of the pump a minimum inlet pressure at the suction port must be assured. The minimum inlet pressureis related to the rotational speed of the fixed pump.
inletpressurepabs.mininbar
speed n/nmax in rpm
2.01.81.61.41.21.00.8
bar
0
1
2
3
4
psi
0
15
30
45
60sizes 250...1000
sizes 5...200Note:
- max. permissible speed nmax limit (speed limit)
- min. permissible pressure at port S
- admissible values for the drive shaft seal (see next page).
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
6/28
6/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Shaft seal ring
Permissible pressure load
The service life of the shaft seal ring is affected by the speed ofthe pump and the case drain pressure. The permitted loading
with intermittent case drain pressure depends on the rotationalspeed (see chart). Short-term (t < 5 min) pressure spikes of upto 145 psi (10 bar) absolute are permitted.
The average permanent case drain pressure must not exceed43.5 psi (3 bar) absolute.
The pressure in the case must be equal to or greater than theexternal pressure on the shaft seal.
Sizes 10...200
perm.pressurepabs.max.
(bar
)
speed n (rpm)
sizes 10, 12, 16
sizes 23, 28, 32
size 45
sizes 56, 63
size 200
sizes 160, 180
sizes 107, 125
sizes 80, 90
Sizes 250...1000
perm
.pressurepabs.max.
(bar)
speed n (rpm)
size 355
size 500
sizes 1000
size 250
sizes 710
Temperature range
The FKM shaft seal is admissible for a housing temperaturerange from-13F to +240F (-25C to +115C) at sizes 5...200 and-13F to +195F (-25C to +90C) at sizes 250...1000
Note:
For applications below -13F (-25 C) a Buna-N (NBR) shaftseal is necessary (admissible temperature range -40 F to+195 F / -40 C to +90 C). Please contact us.
Technical DataDirection of flow
Direction of rotation, viewed on shaft endclockwise counter-clockwise
S to B S to A
Long-life bearing (sizes 250...1000)
For long service life and use with HF hydraulic fluids. Same ex-ternal dimensions as the pump with standard long-life bearingcan be supplied. Flushing of bearing and case via the U-port isrecommended.
Flow (recommended)
Size 250 355 500 710 1000
qv flow gpm 2.6 4.2 4.2 4.2 4.2
L/min 10 16 16 16 16
Symbol
Connections
A, B Service line portS Suction portT1, T2 Drain portsR/U Port for bearing flushing
B
ST2
T1
R/U
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
7/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 7/28
Technical DataTable of values (theoretical values, without considering mh and v; values rounded)
Size 5 10 12 16 23 28 32 45 56 63 80
Diplacement Vg in3 0.30 0.63 0.73 0.98 1.40 1.71 1.95 2.78 3.42 3.84 4.91
cm3 4.93 10.3 12 16 22.9 28.1 32 45.6 56.1 63 80.4
Speed max. nmax1
) rpm 5600 3150 3150 3150 2500 2500 2500 2240 2000 2000 1800nmax limit 2) rpm 8000 6000 6000 6000 4750 4750 4750 4250 3750 3750 3350
Flow max. qV max gpm 7.3 8.6 10.0 13.2 15.1 18.5 21.1 27.0 29.6 33.3 38.0
L/min 27.6 32.4 37.8 50 57 70 80 102 112 126 144
Power at p = 5100 psi Pmax HP 19.53) 25 30 39 44 55 63 80 88 99 113
p = 350 bar Pmax kW 14.53) 18.9 22 29.2 41 47 59.5 65 73.5 84
p = 5800 psi Pmax HP 30 34 45 51 63 71 91 100 113 129
p = 400 bar Pmax kW 22 25 34 38 47 53 68 75 84 96
Torque at p = 5100 psi T lb-ft 183) 42 50 65 94 116 132 189 232 260 331
p = 350 bar T Nm 24.7 3) 57 67 88 126 156 178 254 312 350 445
p = 5800 psi T lb-ft 48 56 75 107 131 150 214 263 295 377
p = 400 bar T Nm 65 76 101 145 178 203 290 356 400 511
Mass moment of inertiaaround output shaft
J lbs-ft2 0.0019 0.00950.0095 0.00950.0285 0.02850.0285 0.05690.0997 0.09970.1708kgm2 0.00008 0.0004 0.0004 0.0004 0.0012 0.0012 0.0012 0.0024 0.0042 0.0042 0.0072
Case fill capacity gal 0.045 0.045 0.045 0.053 0.053 0.053 0.087 0.119 0.119 0.145
L 0.17 0.17 0.17 0.20 0.20 0.20 0.33 0.45 0.45 0.55
Weight (approx.) m lbs 5.5 12 12 12 21 21 21 30 40 40 51
kg 2.5 5.4 5.4 5.4 9.5 9.5 9.5 13.5 18 18 23
Size 90 107 125 160 180 200 250 355 500 710 1000
Displacement Vg in3 5.49 6.51 7.63 9.79 10.98 12.20 15.25 21 .66 30.51 43.33 61 .02
cm3 90 106.7 125 160.4 180 200 250 355 500 710 1000
Speed max. nmax1) rpm 1800 1600 1600 1450 1450 1550 1500 1320 1200 1200 950
nmax limit2) rpm 3350 3000 3000 2650 2650 2750 1800 1600 1500 1500 1200
Flow max. qV max gpm 42.8 44.9 52.8 61.2 69.0 81.9 99.1 123.9 158.5 218.2 251.0L/min 162 170 200 232 261 310 375 469 600 826 950
Power at p = 5100 psi Pmax HP 127 134 157 183 205 244 295 368 472 670 747
p = 350 bar Pmax kW 95 100 117 135 152 181 219 273 350 497 554
p = 5800 psi Pmax HP 145 153 179 208 233 277
p = 400 bar Pmax kW 108 114 133 155 174 207
Torque at p = 5100 psi T lb-ft 372 442 517 664 746 828 1036 1470 2070 2940 4141
p = 350 bar T Nm 501 594 696 893 1003 1114 1393 1978 2785 3955 5570
p = 5800 psi T lb-ft 422 500 586 752 845 938
p = 400 bar T Nm 572 678 795 1020 1145 1272
Mass moment of inertiaaround output shaft
J lbs-ft2 0.1708 0.2753 0.2753 0.5221 0.5221 0.8970 1 .4475 2.4205 4.2240 13.052 13.052
kgm2 0.0072 0.0116 0.0116 0.0220 0.0220 0.0378 0.061 0.102 0.178 0.55 0.55
Case fill capacity gal 0.145 0.211 0.211 0.291 0.291 0.713 0.660 0.925 1.110 2.113 2.113
L 0.55 0.8 0.8 1.1 1.1 2.7 2.5 3.5 4.2 8 8
Weight (approx.) m lbs 51 71 71 99 99 145 161 242 342 715 741
kg 23 32 32 45 45 66 73 110 155 325 3361) The values shown are valid for an absolute pressure (pabs) of 14.5 psi (1 bar) at the suction inlet S and when operated on mine-
ral oil (with a specific mass of 7.36 lbs/gal (0.88 kg/L)).2) By increase of the input pressure (pabs > 14.5 psi / 1 bar) the rotational speeds can be increased to the max. admissible speeds
nmax limit (speed limits) (see diagram page 8).3) p = 4600 psi (315 bar)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
8/28
8/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
)
)
)(
(
(
Technical DataDetermining the size
Vg n v Vg n vFlow qv = gpm qv = L/min
231 1000
Vgp Vgp
Input torque T = lb-ft T = Nm24 mh 20 mh
2 T n qvp 2 T n qvpInput power P = = HP P = = kW
33 000 1714 t 60 000 600 t
Vg = Diplacement per revolution in in3 (cm3)
p = Differential pressure in psi (bar)
n = Speed in rpm
v = Volumetric efficiency
mh = Mechanical-hydraulic efficiency
t = Overall efficiency
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
9/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 9/28
opt
opt
opt
opt
Technical DataPermissible radial and axial loading on the drive shaftThe values given are maximum values and do not apply to continous operation.
Size 5 10 12 16 23 28 32 45 56 63 80
Radial force, max. 1)
at distance a(from shaft collar) a
FqFq max lbf 160 472 562 730 865 1079 1214 1630 1832 2057 23042)
N 710 2100 2500 3250 3850 4800 5400 7250 8150 9150 10250a in 0.47 0.63 0.63 0.63 0.63 0.63 0.63 0.71 0.71 0.71 0.79
mm 12 16 16 16 16 16 16 18 18 18 20
Axial force, max. 3)
+Fax
+Fax max lbf 40 72 72 72 112 112 112 142 180 180 225
N 180 320 320 320 500 500 500 630 800 800 1000
Fax max lbf 40 72 72 72 112 112 112 142 180 180 225
N 180 320 320 320 500 500 500 630 800 800 1000
Permissible axial force/psi (bar)operating pressure
Fax per./psi(bar)
lbf/psi 0.023 0.05 0.05 0.05 0.08 0.08 0.08 0.11 0.13 0.13 0.16
N/bar 1.5 3.0 3.0 3.0 5.2 5.2 5.2 7.0 8.7 8.7 10.6
Size 90 107 125 160 180 200 250 355 500 710 1000
Radial force, max. 1)at distance a(from shaft collar)
Fq max lbf 25742)2720 3170 3664 4114 5148 270 337 427 674 584
a
FqN 11450 12100 14100 16300 18300 22900 12004) 15004) 19004) 30004)26004)
a in 0.79 0.79 0.79 0.98 0.98 0.98 1.61 2.07 2.07 2.66 2.66
mm 20 20 20 25 25 25 41 52.5 52.5 67.5 67.5
Axial force, max. 3) +Fax max lbf 225 281 281 360 360 360 450 562 674 989 989
+Fax
N 1000 1250 1250 1600 1600 1600 2000 2500 3000 4400 4400
Fax max lbf 225 281 281 360 360 360 450 562 674 989 989
N 1000 1250 1250 1600 1600 1600 2000 2500 3000 4400 4400
Permissible axial force/psi (bar)operating pressure
Fax per./psi(bar)
lbf/psi 0.16 0.20 0.20 0.26 0.26 0.26 5) 5) 5) 5) 5)
N/bar 10.6 12.9 12.9 16.7 16.7 16.7
1) during intermittent operation (sizes 5...200)2) value for Q-shaft: Fq max = 2023 lbf (9000 N)3) max. permissible axial force when stopped or when axial piston unit working in zero pressure conditions.4) when stopped or when axial piston unit working in pressureless conditions. Higher forces are permitted when under pressure.
Please contact us.5) please contact us
When considering the permissible axial force, the force-transfer direction must be taken into account.
Fax max = increase in service life of bearings
+ Fax max = reduction in service life of bearings (avoid if at all possible)
Clockwise directionof rotation
Pressure on port B
Clockwise directionof rotation
Pressure on port B
Counter-clockwisedirection of rotation
Pressure on port A
Effect of radial force Fq on the service life of the bearings
By selecting a suitable force-transfer direction of Fq, the stresson the bearing caused by the internal transmission forces canbe reduced, thus achieving the optimum service life for thebearing. Recommended position of mating gear depending ondirection of rotation. Examples:
Gear drive V-belt drive
Size opt. opt.
10-180 70 45
200-1000 45 70
Gear drive V-belt drive
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
10/28
10/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Ordering Code / Standard Program Size 5
Additional instructions in text form
Seals
The fixed pump A2F5 is equipped withBuna-N (NBR) seals in standard design.
In case of need FKM- (fluor-caoutchouc)
seals please indicate when ordering inclear text:
"with FKM-seals"
Axial piston unit
01 Bent axis design, fixed displacement A2FSize
02
Size 5
Displacement Vg in3/rev. 0.30
cm3/rev. 4.93
Series
03 60
Direction of rotation
04Viewed on shaft end clockwise R
counter-clockwise L
Shaft end
05Parallel keyed shaft DIN 6885 BTapered shaft with threaded end and woodruff key per DIN 6888 C
Service line ports
06 Threaded ports A und B at side, metric 7
A2F 5 / 60 701 02 03 04 05 06
Unit Dimensions, Size 5 ISO Design Please request a certified installation drawingbefore finalizing your design.Dimensions in inches and (millimeters)
Shaft ends
B Parallel keyed shaftDIN 6885 A4x4x20 (mm)pN = 3000 psi (210 bar)
C Tapered shaft with threaded end andwoodruff key (3x5 mm) DIN 6888(taper 1:10) pN = 4600 psi (315 bar)
Ports
B (A) Service line portDIN 3852
M18x1.5;0.47 (12) deep
100 lb-ft 3)(140 Nm)
S Suction portDIN 3852
M22x1.5;0.55 (14) deep
155 lb-ft 3)(210 Nm)
T1, T2 Case drain portsDIN 3852
M10x1;0.31 (8) deep
20 lb-ft 3)(30 Nm)
1) centering bore according to DIN 332 (thread accordingto DIN 13), tightening torque see safety instructions
2) thread according to DIN 3852,max. tightening torque: 20 lb-ft (30 Nm)
3) please observe the general notes for the max.tighteningtorques on page 28
Clockwise rotationCounter-clockwise rotation:port plate is rotatedthrough 180
(4)0.16
(51)2.01
(10)0.39
(8)0.31
(24)0.94
(60)2.36
25
-0.046
DIA2.3604
(DIA60
)
DIA2.3622
45 45
0.1
DIA
2.9488
(DIA
75
)
DIA
2.9567
(70)
2.76
(6.4)
0.25
(70)2.76(R
6)R0.24
(84)3.31(68)2.68
(51)
2.01
(28)
1.10
(7.4)
0.29
(52)2.05
Y
B(S)T1 (T2)
B S
(4)0.16
(33)1.30
(22)0.87
(7.3)
0.29
(DIA12.8)
DIA0.50
M10x12)3)
(DIA15)
DIA0.59
(10)0.39
(3.2)0.13
(24)0.95
(13.5)
0.53
DIA0.472
DIA0.473
(R0.4)
R0.02 (
DIA15)
DIA0.59(
DIA12+0.0
01)
+0.0
12
M4x0.7
1)3)
Detail Y
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
11/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 11/28
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Sizes 10, 12, 16 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Flange SAE J744
101-2 (B)
Shaft ends
S Splined shaft 7/8 in 13T 16/32 DP 1)(SAE J744 22-4 (B))
pN = 5800 psi (400 bar)
B Parallel keyed shaftDIN 6885 AS8x7x32 (mm)
pN = 5100 psi (350 bar)
Ports
B (A) Service line port ISO 11926 1 1/16 in -12 UN-2B; 0.79 (20) deep 265 lb-ft (360 Nm) 4)
S Suction port ISO 11926 1 5/16 in -12 UN-2B; 0.79 (20) deep 400 lb-ft (540 Nm) 4)
T1, T2 Case drain ports (T2 plugged) ISO 11926 9/16 in -18 UNF-2B; 0.51 (13) deep 60 lb-ft (80 Nm) 4)
R Air bleed, Oil drain (plugged) ISO 11926 5/16 in -24 UNF-2B; 0.93 (10) deep 7 lb-ft (10 Nm) 4)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) centering bore according to DIN 332 (thread according to DIN 13)4) please observe the general notes for the max. tightening torques on page 28
(42.5)1.67
(7.9)0.31
(180)7.09(159)6.26
(143)5.63
(108)4.25
(12)0.47
-0.05
DIA3.9980
DIA4.0000
(DIA101.6
)
(9.7)0.38
(36)1.42
(72)2.83
(94)
3.70
(56)
2.20
(69)
2.72
(29)
1.14
(174)6.85
(146)5.75
(14.3)0.56
(121)
4.76
(14)0.55
(49)
1.93
(53.5)
2.11 4
0
SB(A)
R
T2
T1
Y
(7)
0.27
(8h9)0.31350.3150
(28)
1.10
(DIA25
)
DIA0.9843
DIA0.9848
+0.015
+0.002
M10x1.5
3)4)
(22)
E1x0.2DIN 509
0.87
(7.5)0.30
(40)1.57
(DIA28)
DIA1.10
(33.5)1.32
5/16-18UNC-2B
2)4)
(8)0.31
(6)0.24 (19)
0.75
(DIA28)
DIA1.10
Detail Y
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
12/28
12/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Sizes 23, 28, 32 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
S Splined shaft 1 1/4 in 14T 12/24 DP 1)(SAE J744 32-4 (C))
pN = 5800 psi (400 bar)
B Parallel keyed shaftDIN 6885 AS8x7x40 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 1/2 in
Fastening threads B/A ISO 68 5/16 in-18 UNC-2B; 0.71 (18) deep see safety instructions
S Suction port (standard pressure series) SAE J518 3/4 in Fastening threads S ISO 68 3/8 in-16 UNC-2B; 0.79 (20) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) ISO 11926 3/4 in-16 UNF-2B; 0.59 (15) deep 120 lb-ft (160 Nm) 4)
R Air bleed, Oil drain (plugged) ISO 11926 5/16 in-24 UNF-2B; 0.39 (10) deep 7 lb-ft (10 Nm) 4)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) centering bore according to DIN 332 (thread according to DIN 13)4) please observe the general notes for the max. tightening torques on page 28
T1
T2
B(A) Y
R
S
45 45
(146)5.75
(14.3)
0.56
(146)
5.75
(47.6)1.87
(14)0.55
(22.2)
0
.87
(19)
0
.75
(DIA
162)
DIA6.38
(27)
1.06
(210)8.27(186)7.32
(161)6.34(59)2.32
(31)1.22
(12.7)0.50
(120)
4.72
(91)
3.58
(70)
2.76
(125)4.92
(7.9)0.31
(20)0.79
-0.05
DIA4.9980
DIA5.0000
(DIA127
)
40
(60)
2.36
(40.5)1.
59
(13)0.
51
(18.2)
0.72
(106)
4.17
7/16-14UNC-2B
2)4)
(DIA35)
DIA
1.3
8
(8)0.31
(48)1.89
(9.5)0.37
(28)1.10
0.31350.3150
(8h9)
(7)
0.27
(22)
E1x0.2DIN 509
0.87
M10x1.5
3)4)
(33)
1.30
(DIA35)
DIA1.38
(50)1.97
+0.002
+0.015
(DIA30
)
DIA1.182
DIA1.181
(7.5)0.30
Detail Y
Flange SAE J744
127-4 (C)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
13/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 13/28
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Size 45 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
S Splined shaft 1 1/4 in 14T 12/24 DP 1)(SAE J744 32-4 (C))
pN = 5800 psi (400 bar)
P Parallel keyed shaftDIN 6885 AS8x7x50 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 3/4 in
Fastening threads B/A ISO 68 3/8 in-16 UNC-2B; 0.82 (21) deep see safety instructions
S Suction port (standard pressure series) SAE J518 1 in Fastening threads S ISO 68 3/8 in-16 UNC-2B; 0.79 (20) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) ISO 11926 3/4 in-16 UNF-2B; 0.59 (15) deep 120 lb-ft (160 Nm) 4)
R Air bleed, Oil drain (plugged) ISO 11926 7/16 in-20 UNF-2B; 0.47 (12) deep 30 lb-ft (40 Nm) 4)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) centering bore according to DIN 332 (thread according to DIN 13)4) please observe the general notes for the max. tightening torques on page 28
Y
1T
R 2T
S
B(A)
(7.9)0.31
(20)0.79
(65)
2.56
(DIA
162)
DIA6.3
8
(114.6)4.51
(179)7.05
(133)5.24
-0.05
DIA4.9980
DIA5.0000
(DIA127
)
(230)9.06
(146)
5.75
(146)5.75
(14.3)
0.56
45 45
40
(66)2.60
(12.7)0.50
(34)1.34
(50.8)2.
00
(118)
4.65
(205)8.07
(26.2)
1.0
3
(20)0.79
(25)
0.9
8
(52.4)2.06
(19)0.
75
(23.8)
0.94
(132)
5.20
(102)
4.02
(30)
1.18
(80)
3.15
7/16-14UNC-2B
2)4)
(DIA35)
DIA
1.3
8
(8)0.31
(48)1.89
(9.5)0.37
(28)1.100.31500.3135(8h9)
(7)
0.27
(60)2.36
M12x1.753)4)
(33)
1.30
+0.002
DIA1.181
+0.015
DIA1.182
(DIA30
)
(9.5)0.37
(28)
E1x0.2DIN 509
1.10
(DIA35)
DIA1.38
Detail Y
Flange SAE J744
127-4 (C)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
14/28
14/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Sizes 56, 63 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
S Splined shaft 1 1/4 in 14T 12/24 DP 1)(SAE J744 32-4 (C))
pN = 5100 psi (350 bar)
T Splined shaft 1 3/8 in 21T 16/32 DP 1)pN = 5800 psi (400 bar)
B Parallel keyed shaftDIN 6885 AS10x8x50 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 3/4 in
Fastening threads B/A ISO 68 3/8 in-16 UNC-2B; 0.82 (21) deep see safety instructions
S Suction port (standard pressure series) SAE J518 1 in Fastening threads S ISO 68 3/8 in-16 UNC-2B; 0.79 (20) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) ISO 11926 3/4 in-16 UNF-2B; 0.59 (15) deep 120 lb-ft (160 Nm) 4)
R Air bleed, Oil drain (plugged) ISO 11926 7/16 in-20 UNF-2B; 0.47 (12) deep 30 lb-ft (40 Nm) 4)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) centering bore according to DIN 332 (thread according to DIN 13)4) please observe the general notes for the max. tightening torques on page 28
(DIA16
2)DIA6
.38
-0.05
DIA4.9980
DIA5.0000
(DIA127
)
(12.7)0.50
(146)
5.75
(146)5.75
(14.3)
0.56
45
(71.6)
2.82
(65.4)
2.57
(221)8.70
(128)
5.04
(19)0.
75
40
(141)
5.55
(109)
4.29
(87)
3.43
(195)7.68
45
(248)9.76
(74)2.91
(36)1.42
(23.8)
0.94
(50.8)2.
00
(33)
1.30
(143)5.63
(7.9)0.31
(20)0.79
(26.2)
1.0
3
(25)0.98
(52.4)2.06
(23)0.91(68)2.68
1T
2TR
B(A)
S
Y
0.39230.3937
(10h9)
(8)
0.31
+0.002
DIA1.378
+0.018
DIA1.379
(DIA35
)
M12x1.753)4)
(9.5)0.37
(DIA40)
DIA1.57
(60)2.36
(38)
1.50
(28)E1x0.2DIN 509
1.10
7/16-14UNC-2B
2)4)
(DIA40)
DIA1.57
(8)0.31
(48)1.89
(9.5)0.37
(28)1.10
7/16-14UNC-2B
2)4)
(DIA40)
DIA1.57
(8)0.31
(48)1.89
(9.5)0.37
(28)1.10
Detail Y
Flange SAE J744
127-4 (C)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
15/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 15/28
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Sizes 80, 90 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
U Splined shaft 1 3/8 in 21T 16/32 DP 1)pN = 5800 psi (400 bar)
Q Splined shaft 1 1/4 in 14T 12/24 DP 1)(SAE J744 32-4 (C))
Size 80: pN = 4350 psi (300 bar)Size 90: pN = 4000 psi (280 bar)
Ports
B (A) Service line port (high pressure series) SAE J518 1 in Fastening threads B/A ISO 68 7/16 in-14 UNC-2B; 0.87 (22) deep see safety instructions
S Suction port (standard pressure series) SAE J518 1 1/4 in Fastening threads S ISO 68 7/16 in-14 UNC-2B; 1.02 (26) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) ISO 11926 7/8 in-14 UNF-2B; 0.67 (17) deep 180 lb-ft (240 Nm) 3)
R Air bleed, Oil drain (plugged) ISO 11926 7/16 in-20 UNF-2B; 0.47 (12) deep 30 lb-ft (40 Nm) 3)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) please observe the general notes for the max. tightening torques on page 28
(12.7)0.50
(8)0.31
(DIA
162)
DIA
6.38
(161)6.34
(253)9.96
(20)0.79
-0.05
DIA4.9980
DIA5.0000
(DIA127
)
(83)
3.27
(93)3.66
(41)
1.61
(146)
5.75
(146)5.75
(14.3)
0.56
4545
40
(40)1.57
(70.9)
2.79
(225)8.86
(158)
6.22
(122)
4.80
(99)
3.90
(282)11.10
(183
)
5.43
(57.2)2.
25
(25)0.
98
(27.8)
1.09
(30
.2)
1.1
9
(32)1.26
(58.7)2.31
(25)0.98
(73)2.87
S
B(A)
RT2
T1
Y
7/16-14UNC-2B
2)3)
(8)0.31
(9.5)0.37
(DIA45)
DIA1.77
(48)1.89
(28)1.10
(48)1.89
(8)0.31
(9.5)0.37
(28)1.10
7/16-14UNC-2B
2)3)
(DIA45)
DIA1.77
Detail Y
Flange SAE J744
127-4 (C)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
16/28
16/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Sizes 107, 125 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
S Splined shaft 1 3/4 in 13T 8/16 DP 1)(SAE J744 44-4 (D))
pN = 5800 psi (400 bar)
U Splined shaft 1 1/2 in 23T 16/32 DP 1)pN = 5800 psi (400 bar)
B Parallel keyed shaftDIN 6885 AS14x9x63 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 1 1/4 in
Fastening threads B/A ISO 68 1/2 in -13 UNC-2B; 0.75 (19) deep see safety instructions
S Suction port (standard pressure series) SAE J518 1 1/2 in Fastening threads S ISO 68 1/2 in -13 UNC-2B; 0.95 (24) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) ISO 11926 7/8 in -14 UNF-2B; 0.67 (17) deep 180 lb-ft (240 Nm) 4)
R Air bleed, Oil drain ( plugged) ISO 11926 7/16 in -20 UNF-2B; 0.47 (12) deep 30 lb-ft (40 Nm) 4)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) centering bore according to DIN 332 (thread according to DIN 13)4) please observe the general notes for the max. tightening torques on page 28
(277)10.91(306)12.05
(246)9.69
(175)6.89
(7.9)0.31
(25)0.98
(44)1.73
(96.9)3.81
(12.7)0.50
(32)1.
26
(66.7)2.
63
(150)
5.91
-0.05
DIA5.9980
DIA6.0000
(DIA152.4
)
(31.8)
1.25(43)
1.69
(173)
6.81
(110)
4.33
(20.6)
0.81
(DIA2
28.6)
DIA9
.00(200)
7.87
(200)7.87
40
45 45
(76.5)
3.01
(86)
3.39
(89)3.50 (20)0.79
(38)1.97
(35.7)
1.4
1
(69.9)2.75
(136)
5.35
Y B(A)
S
R
T1
T2
(8)0.31
(12)0.47
(DIA50)
DIA1.97
(62)2.44
(36)1.42
5/8-11UNC-2B
2)4)
(9)
0.35
(14h9)
0.55120.5495
(DIA50)
DIA1.97
(80)3.15
(12)E1x0.2DIN 5090.47
(36)1.42
(48.5)
1.91
+0.002
DIA1.771
+0.018
DIA1.772
(DIA45
)
M16x23)4)
(12)0.47
(12)0.47
(67)2.64
5/8-11UNC-2B
2)4)
(36)1.42
(DIA50)
DIA1.97
Detail Y
Flange SAE J744
152-4 (D)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
17/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 17/28
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Sizes 160, 180 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
S Splined shaft 1 3/4 in 13T 8/16 DP 1)(SAE J744 44-4 (D))
pN = 5800 psi (400 bar)
B Parallel keyed shaftDIN 6885 AS14x9x70 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 1 1/4 in
Fastening threads B/A ISO 68 1/2 in-13 UNC-2B; 0.75 (19) deep see safety instructions
S Suction port (standard pressure series) SAE J518 1 1/2 in Fastening threads S ISO 68 1/2 in-13 UNC-2B; 0.95 (24) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) ISO 11926 7/8 in-14 UNF-2B; 0.67 (17) deep 180 lb-ft (240 Nm) 4)
R Air bleed, Oil drain (plugged) ISO 11926 9/16 in-20 UNF-2B; 0.51 (13) deep 60 lb-ft (80 Nm) 4)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) centering bore according to DIN 332 (thread according to DIN 13)4) please observe the general notes for the max. tightening torques on page 28
(326)12.83
(269)10.59
(303)11.93
(190)7.48
(31.8)
1.25
(69.9)2.75
(42)1.65
(96)
3.78
(87)
3.43
(66.7)2.
63
(32)1.
26
(180
)
7.09
(35
.7)
1.
41
(DIA229)
DIA9
.02
(200)7.87
45 45
(200)
7.87
(21)
0.83
(101)3.98 (15)0.59
(25)0.98
(149)
5.87
(121)
4.76
40
(47)
1.85
(104)4.09
(45)1.77
(12.7)0.50
(7.9)0.31
-0.05
DIA5.9980
DIA6.0000
(DIA152.4
)
(189)
7.44
Y
2TR
1T
S
B(A)
(9)
0.35
(14h9)
0.55120.5495
(90)3.54
(12)0.47
(36)1.42
(53.5)
2.11
(DIA60)
DIA2.36
+0.002
DIA1.968
+0.018
DIA1.969
(DIA50
)
M16x23)4)
R0.06
(R1.6)
(67)2.64
(36)1.42
(DIA60)
DIA2.36
5/8-11UNC-2B
2)4)
(12)0.47
(12)0.47
Detail Y
Flange SAE J744
152-4 (D)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
18/28
18/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Size 200 ISO Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
A Splined shaft DIN 5480W50x2x30x24x9g
pN = 5800 psi (400 bar)
B Parallel keyed shaftDIN 6885 AS14x9x80 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 1 1/4 in
Fastening threads B/A DIN13 M14x2; 0.75 (19) deep see safety instructions
S Suction port (standard pressure series) SAE J518 3 1/2 in Fastening threads S DIN13 M16x2; 0.95 (24) deep see safety instructions
T1, T2 Case drain ports (T1 plugged) DIN 3852 M22x1 .5; 0.55 (14) deep 155 lb-ft (210 Nm) 2)
R Air bleed, Oil drain (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
1) centering bore according to DIN 332 (thread according to DIN 13)2) please observe the general notes for the max. tightening torques on page 28
T1
T2R Y
S
45
(22)
0.87
(236)
9.29
45(236)9.29
(32)
1.26
(DIA
250)
DIA9.8
4
-0.029
DIA7.8740
DIA7.8728
(DIA200
)
(102.5)
4.04
(16)0.63
(89)3.50
(351)13.82(319)12.56
(265)10.43
(9)0.35
(32)1.26
(100)
3.94
(169)
6.65
(75)
2.95
25
(108)4.25
(211)
8.31
(90)
3.54
(121)
4.76
(31.8)
1.25
(66
.7)
2.63
(120.7
)
4.75
(69.9)2.75
(157)6.18
(77)
3.03
(9)
0.35
(14h9)
0.55120.5495
(100)3.94
(12)0.47
(36)1.42
(53.5)
2.11
(DIA70)
DIA2.76
+0.002
DIA1.968
+0.018
DIA1.969
(DIA50
)
M16x21)2)
R0.06(R1.6)M
161)2)
(11)0.43
(55)2.17
(12)0.47
(DIA70)
DIA2.76
(36)1.42
Detail Y
FlangeISO 3019-2
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
19/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 19/28
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Size 250 SAE Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
S Splined shaft 2 in 15T 8/16 DP 1)(SAE J744 50-4 (F))
pN = 5100 psi (350 bar)
K Parallel keyed shaft0.5x0.5x3.0 ( in) 12.7x12.7x76.7 (mm)
pN = 5100 psi (350 bar)
Ports
B (A) Service line port (high pressure series) SAE J518 1 1/4 in Fastening threads B/A ISO 68 1/2 in -13 UNC-2B; 0.79 (20) deep see safety instructions
S Suction port (standard pressure series) SAE J518 2 1/2 in Fastening threads S ISO 68 1/2 in -13 UNC-2B; 0.79 (20) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) ISO 11926 7/8 in -14 UNF-2B; 0.67 (17) deep 180 lb-ft (240 Nm) 3)
U Port for bearing flushing (plugged) ISO 11926 9/16 in -18 UNF-2B; 0.51 (13) deep 60 lb-ft (80 Nm) 3)
1) ANSI B92.1a-1976, 30 pressure angle, flat root side fit, tolerance class 52) thread according to ISO 683) please observe the general notes for the max. tightening torques on page 28
(7.9)0.31
-0.0
5
DIA6.498
(DIA165.1
)
DIA6.500
DIA5.51
(DIA140)
(64)2.52(16)0.63
(124)4.88(25)0.98
(105)
4.13
(105
)
4.13
26
.5
(124)4.88
(172)
6.77
(82)
3.23
(371)14.61
(351)13.82
(309)12.17
45
(262)
10.31
(20.6)
0.81
(262)10.31
4x90(=36
0)
T2
T1U
Y
(66
.7)
2.63 1
.26
(32)
(210)
8.2
7
B(A)
2.48 (63)
(118)
3.50
(12)4.65 0.47
S
(31.8)
1.25
2.0
0
(50.8
)
(88.9)
(DIA317.5)
DIA12.50
0.59 (15)
(DIA60)
DIA2.36
5/8-11UNC-2B
2)3)
-0.89
DIA1.964
-0.74
DIA1.970
(DIA50.8
)
(36)1.42
(12)0.47
(66.7)2.63
+0.025(12.7)
0.5
0.5010
(12.7 )0.5000
-0.03
DIA1.998
DIA2.000
(DIA50.8
)
5/8-11UNC-2B
2)3)
(56.3)
2.22
(79.4)3.13
R0.06
(R1.6)
(36)1.42
(12)0.47
(DIA60)
DIA2.36
Detail Y
Flange SAE J744
165-4 (E)
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
20/28
20/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Size 355 ISO Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
Z Splined shaft DIN 5480W60x2x30x28x9g
pN = 5100 psi (350 bar)
P Parallel keyed shaftDIN 6885 AS18x11x100 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 1 1/2 in
Fastening threads B/A DIN13 M16x2; 0.83 (21) deep see safety instruct ions
S Suction port (standard pressure series) SAE J518 2 1/2 in Fastening threads S DIN13 M12x1.75; 0.67 (17) deep see safety instruct ions
T1, T2 Case drain ports (T2 plugged) DIN 3852 M33x2; 0.71 (18) deep 400 lb-ft (540 Nm) 2)
U Port for bearing flushing (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
MA, MB Measuring ports operating pressure A, B (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
MS Measuring port suction pressure (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
1) centering bore according to DIN 332 (thread according to DIN 13)2) please observe the general notes for the max. tightening torques on page 28
BS
U T1
T2
MB (MA) MS
(18)
0.71
-0.081
DIA11.0204
DIA11.0236
(DIA280
)
(83)3.27
(28)1.10(14)0.55
(350)13.78
(320)12.60
(128)
5.04
(198)
7.80
(102)
4.02
(128)
5.04
3.27 (83) 2230'
(171)
6.73
(335)
13.19
(335)13.19
DIA360)
DIA14.17(D
IA320)
DIA
12.60
0.93 (23.5)1.89 (48)8x45
=360
263
0'
(50)1.97
(50)1.97(60)2.36
(79.4)
3.13
(40)
1.57
(36.5)1.44
(50.8)
2.00
(88.9)3.50
(24
5)
9.65(
63)
2.48
(250)9.84
Y
(11)
0.43
(18h9)
0.70870.7070
+0.011
DIA2.363
+0.030
DIA2.362
(DIA60
)
M20x2.5
1)2)
(64)
2.52
(105)4.13
(15)0.59
(42)1.65
(DIA70)
DIA2.76
R0.06
(R1.6)
M20x2.5
1)2)
(42)1.65
(15)0.59
(11)0.43
(82)3.23
(DIA70)
DIA2.76
Detail YFlangeISO 3019-2
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
21/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 21/28
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Size 500 ISO Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
Z Splined shaft DIN 5480W70x3x30x22x9g
pN = 5100 psi (350 bar)
P Parallel keyed shaftDIN 6885 AS20x12x100 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 1 1/2 in
Fastening threads B/A DIN13 M16x2; 0.95 (24) deep see safety instructions
S Suction port (standard pressure series) SAE J518 3 in Fastening threads S DIN13 M16x2; 0.95 (24) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) DIN 3852 M33x2; 0.71 (18) deep 400 lb-ft (540 Nm) 2)
U Port for bearing flushing (plugged) DIN 3852 M18x1.5; 0.47 (12) deep 100 lb-ft (140 Nm) 2)
MA, MB Measuring ports operating pressure A, B (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
MS Measuring port suction pressure (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
1) centering bore according to DIN 332 (thread according to DIN 13)2) please observe the general notes for the max. tightening torques on page 28
(DIA315-0.081)
DIA12.4016
DIA12.3984
0.55 (14)
(50)1.97
(65)2.56
(276)10.87
(36.6)1.44
(270)
10.63(7
9.4
)
3.13
(40)
1.58
2230'
(22)
0.878x45
(=36
0)
(375)
14.76
(375)14.76
(DIA400)
DIA15.75(DIA
360)
(DIA
14.17)
(362)14.25(111)4.37
(30)1.18
263
0'
(220)
4.43
(396)15.59
(112.5)
8.66
(142)
5.59
(142)
5.59
3.86 (98)
1.08 (27.5)1.89 (48)
(189)
7.44
(192)
7.56
(62)
2.44
(75)
2.95
(55)2.17
(106.4)4.19
U T1
MB (MA) MS
T2
SB
Y
(12)
0.47
(20h9)
0.78740.7854
(DIA80)
DIA3.15
(74.5)
2.93
+0.030
+0.011
DIA2.7563
(DIA70
)
DIA2.7570
M20x2.5
1)2)
(105)4.13
(15)0.59
(42)1.65
R0.06
(R1.6)
(15)0.59
(DIA80)
DIA3.15
M20x2.5
1)2)
(42)1.65
(80)3.15
(13)0.51
Detail YFlangeISO 3019-2
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
22/28
22/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Size 710 ISO Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
Z Splined shaft DIN 5480W90x3x30x28x9g
pN = 5100 psi (350 bar)
P Parallel keyed shaftDIN 6885 AS25x14x125 (mm)
pN = 5100 psi (350 bar)
PortsB (A) Service line port (high pressure series) SAE J518 2 in
Fastening threads B/A DIN13 M20x2.5; 1.18 (30) deep see safety instructions
S Suction port (standard pressure series) SAE J518 4 in Fastening threads S DIN13 M16x2; 0.95 (24) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) DIN 3852 M42x2; 0.79 (20) deep 530 lb-ft (720 Nm) 2)
U Port for bearing flushing (plugged) DIN 3852 M18x1.5; 0.47 (12) deep 100 lb-ft (140 Nm) 2)
MA, MB Measuring ports operating pressure A, B (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
MS Measuring port suction pressure (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
1) centering bore according to DIN 332 (thread according to DIN 132) please observe the general notes for the max. tightening torques on page 28
(DIA500)
DIA17
.72
(DIA
450)
T2
UT1
18
30
S
B (A)
13.54 (344)
MB (MA)
Y
2230'8x45
(=360
)
3.8
1
(96.8
)
MS
0.8
7(22)
18.31 (465)
18.3
1(465)
1.97(50)
0.55 (14)
5.16 (131)
DIA15.7
480
DIA15.7
445
(DIA
400-0.089)
1.38(35)
6.14(156)
19.96 (507)
19.13 (486)
7.21
(183)
7.21
(183)
5.13 (130.2)
4.0
2
(102)
9.9
2
(252)
3.0
6
(77.8
)
13.3
9
(34
0)
1.9
7
(50)
3.9
4
(
100)
1.75 (44.5)
1.63 (41.5)1.85 (47)
9.2
9(236)
3.35 (85) 2.76 (70)
DIA19.69
(14)
0.55
(25h9)
0.98430.9822
(95)
3.74
(DIA100)
DIA3.94
+0.035
DIA3.5438
(DIA90
)
DIA3.5447
M24x31)2)
+0.013
(130)5.12
(18)0.71
(50)1.97
R0.06
(R1.6)
(DIA100)
DIA3.94
(50)1.97
M24x31)2)
(18)0.71
(105)4.13
(14)0.55
Detail YFlangeISO 3019-2
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
23/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 23/28
Please request a certified installation drawingbefore finalizing your design.
Dimensions in inches and (millimeters)Unit Dimensions, Size 1000 ISO Design
Clockwise rotation Counter-clockwise rotation: port plate is rotated through 180
Shaft ends
Z Splined shaft DIN 5480W90x3x30x28x9g
pN = 5100 psi (350 bar)
P Parallel keyed shaftDIN 6885 AS25x14x125 (mm)
pN = 5100 psi (350 bar)
Ports
B (A) Service line port (high pressure series) SAE J518 2 in Fastening threads B/A DIN13 M20x2.5; 1.18 (30) deep see safety instructions
S Suction port (standard pressure series) SAE J518 4 in Fastening threads S DIN13 M16x2; 0.95 (24) deep see safety instructions
T1, T2 Case drain ports (T2 plugged) DIN 3852 M42x2; 0.79 (20) deep 530 lb-ft (720 Nm) 2)
U Port for bearing flushing (plugged) DIN 3852 M18x1.5; 0.47 (12) deep 100 lb-ft (140 Nm) 2)
MA, MB Measuring ports operating pressure A, B (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
MS Measuring port suction pressure (plugged) DIN 3852 M14x1.5; 0.47 (12) deep 60 lb-ft (80 Nm) 2)
1) centering bore according to DIN 332 (thread according to DIN 13), tightening torque see safety instructions
2) please observe the general notes for the max. tightening torques on page 28
BS
T2
UT
1
MB (MA) MS
(DIA
450)
DIA
17.72
(DIA500)
DIA19.69
(236)
9.29
(468)18.43
5.16 (131)
1.63 (41.5)1.85 (47)
(156)6.14(35)1.38
(183)
7.20
(183)
7.20
(44.5)1.75
(344)13.54
(85)3.35
(34
0)
13.39
(96.8)
3.81 (
50)
1
.97
(465)
18.31
(465)18.31
2230'
(22)
0.878x45
(=36
0)
263
0'
(511)20.12
(277)
10.91
(143)
5.63
DIA15.7480
(DIA400-0.089)
DIA15.7445
(100)
3.94
(77.8)
3.06
(130.2)5.13
(70)2.76
(50)1.97
0.55 (14)Y
(14)
0.55
(25h9)
0.98430.9822
(95)
3.74
(DIA100)
DIA3.94
+0.035
DIA3.5438
(DIA90
)
DIA3.5447
M24x31)2)
+0.013
(130)5.12
(18)0.71
(50)1.97
R0.06
(R1.6)
(DIA100)
DIA3.94
(50)1.97
M24x31)2)
(18)0.71
(105)4.13
(14)0.55
Detail YFlangeISO 3019-2
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
24/28
24/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Installation below the tank
Pumps below min. fluid level in the tank (standard)
Fill axial piston pump before startup via the highestcase drain port
Additional measures required for installation position 2
(shaft facing up): with installation position 2, make sure thatthe pump case is completely full before starting up. Bleedat port R (sizes 10...200) resp. U (sizes 250...1000). An airpocket in the bearing area can cause damage to the pump.
Recommendation: Fill up suction lines
Run the pump at low speed until the system is bledcompletely
Minimum immersion depth of leakage line in tank:7.9 in (200 mm) (relative to the min. fluid level in the tank)
Installation and Commissioning NotesGeneral
The pump case must be completely filled with hydraulic fluid during startup and during operation (filling the case chamber). Thepump must be started at low speed and no load until the system has been bled completely.
If stopped for an extended period, fluid may drain out of the case through the service lines. When restarting, make sure that thecase contains sufficient fluid.
The leakage fluid inside the case chamber must be drained off to the tank through the highest case drain port. The min. suctionpressure at port S must not fall below 12 psi (0.8 bar) absolute (see page 5).
Installation position
Optional.
Installation above the tank
Pump above minimum fluid level in tank
Proceed in same way as below the tank installation
Additional measures for installation positions 1 and 2:If stopped for an extended period, fluid may drain out of the
case chamber through the service lines (air enters throughthe shaft seal). The bearings will therefore not be properlylubricated when the pump is started up again. Fill the axialpiston pump before restarting via the highest case drain port.Installation position 2: bleed at port R (sizes 10...200)resp. U (sizes 250...1000).
Installation position 2 (shaft facing up)
In this installation position the bearings will not be properlylubricated, even if there is still some fluid in the case cham-ber. Putting a check valve (opening pressure 7.25 psi (0.5bar)) in the leakage line can prevent the system emptyingthrough the line.
Note: min. admissible presssure at port S(min. suction pressure see page 5 and 8)
T2
R (U)
S
T1
S
T1
S
T2S
7.25psi(0.5bar)
T1
S
T1
S
T2
R (U)
S
ST2
Installation position 2
Installation position 2
Installation position 1
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
25/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 25/28
Notes
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
26/28
26/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
Notes
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
27/28
RA 91 401/07.05 AA2FO Bosch Rexroth Corp. 27/28
Notes
-
8/6/2019 (Bomba Sellado Sidd)Ra91401_0705
28/28
28/28 Bosch Rexroth Corp. AA2FO RA 91 401/07.05
2005 Bosch Rexroth Corporation
All rights reserved. Neither this document, nor any part of it, may be reproduced,
duplicated, circulated or disseminated, whether by copy, electronic format or any
other means, without the prior consent and authorization of Bosch Rexroth Corp.
The data and illustrations in this brochure/data sheet are intended only to descri-
be or depict the products. No representation or warranty, either express or imp-
lied, relating to merchantability or fitness for intended use, is given or intended by
virtue of the information contained in this brochure/data sheet. The information
contained in this brochure/data sheet in no way relieves the user of its obligation
to insure the proper use of the products for a specific use or application. All
Bosch Rexroth CorporationHydraulicsAxial & Radial Piston Units8 Southchase CourtFountain Inn, SC 29644-9018, USATelephone (864) 967-2777Facsimile (864) 967-8900www.boschrexroth-us.com
General Notes The AA2FO pump is designed to be used in open circuits.
Project planning, assembly, and startup of the pump require the involvement of trained personnel.
The working and functional ports are only designed to accommodate hydraulic piping.
Suction lines may need to be sized bigger than the suction port provided, depending on operation conditions, as required by
good design practices. A smooth transition is to be provided in these installation conditions. Tightening torques
- The tightening torques specified in this data sheet are maximum values and may not be exceeded(maximum value for screw thread). Manufacturer specifications for the max. permissible tightening torques of the used fitt ingsmust be observed!
- For ISO 68 / DIN 13 fastening screws we recommend checking the tightening torque individually according to VDI 2230Edition 2003.
The housing temperature rises during and shortly after operation. Take suitable safety precautions (e.g. wear protective clothing).
The data and information contained herein must be adhered to.