brief instructions checking the lubrication system
TRANSCRIPT
Checking the lubrication system
Start
End
Clean the rails and racks
Lubricate rails and racks with lubricating spray(material number 10406825)
Remove all lubrication lines from the lubricant pump
Start the lubricant pump's lubrication cycle
Does lubricant flowout at all hydraulic
outputs of the lubricantpump?
Mount all lubrication lines on the hydraulic outputs ofthe lubricant pump
Fill lubrication line withlubricant. Remove air in
lubrication line. Remove kinks
Start the lubricant pump's lubrication cycle
Expose lubrication point Remount lubrication point
Yes
No
Is the lubrication linefilled without air
bubbles and kinks?
Yes
No
Check voltage supply andfunction of the lubricant pump
and correct if necessary
Replace lubricating element /lubricating pinion if necessary,
then pre-lubricate
Lubricating element /lubricating pinionsaturated with
lubricant and intact?
Yes
No
Does lubricant flowout at lubrication
point?
Yes
No
Other lubricationpoints available?
Yes
No
Start lubrication point checkI
II
III
IV
VI
V
VII
VIII
IX
X
XI
XII
• After cleaning work or during standstill times of 1 to 4 weeks, check the lubricant film on the rails and racks (II) and the lubrication lines for air bubbles and kinks (VII) before commissioning. If necessary, carryout a check of the complete lubrication system.
• As operator, check the lubrication system during initial commissioning, after standstill times of more than 4 weeks, if lubricant film is not present, and after the lubricant cartridge or the lubricant pump of thelubrication system has been replaced.The operator is always responsible for adequate and properly functioning lubrication.
BRIEF INSTRUCTIONS
Checking the lubrication system Process owner: GCH, R&D, Head of R&D; ernrot
EN DE
ES ZH FR IT RU PL
Page 1/2larwuexx.11.2020Mat.Nr.: 10409166
54043196050974987_v7.0_EN-US
ü û
III
III
IVV
IV
II
V
ü û
ü û
VIII
404 D
LS
40
2
40
2 B
+_
IXX X
I
ü û
ü û
XII
404 D
LS
402
402 B
+_
Lub
rica
ntS
peci
ficat
ions
Lub
rica
nt q
uant
ity
Elka
lub
FLC
8 H
1C
anno
t be
det
erm
ined
Run
ning
sur
face
s of
the
rol
ler
and
pini
on n
eed
to b
e co
vere
d co
m-
plet
ely
by a
lubr
icat
ing
film
Cle
anin
g ag
ents
mild
uni
vers
al c
lean
er fr
ee fr
om a
rom
atic
com
poun
ds (
e.g.
Mot
orex
OPA
L 50
00)
Lubr
icant
, Cle
anin
g ag
ents
: Pre
-lubr
icatin
g ra
ils a
nd r
acks
BRIEF INSTRUCTIONS
Checking the lubrication system Process owner: GCH, R&D, Head of R&D; ernrot
404D
LSEN
404D
LSD
E
404D
LSES
404D
LSZ
H
402
/ 402
B EN
402
/ 402
B D
E
402
/ 402
B ES
402
/ 402
B Z
H
Page 2/254043196050974987_v7.0_EN-US larwuexx.11.2020Mat.Nr.: 10409166