bsc commands for beginners

BSC COMMANDS

FOR BEGINNERS

System Group

BSC COMMANDSFor beginners

2 (21)

CONTENTS

1. INTRUDUCTION....................................................................................................4

2. OUTPUT RADIO NETWORK CONFIGURATION.............................................6

3. ALARMS HANDLING...........................................................................................6

3.1. List Alarms Currently On...............................................................................6

3.2. List Alarm History..........................................................................................6

4. SW PACKAGE HANDLING..................................................................................7

4.1. List SW package of BCF................................................................................7

4.2. Attach Software Package To BCF..................................................................7

4.3. Activate BCF software package.....................................................................7

5. CHANGE BCF, BTS AND TRX STATE...............................................................8

5.1. Locking the BCF, BTS, TRX and Timslot.....................................................8

5.2. Forced Handover............................................................................................8

6. POWER CONTROL PARAMETER HANDLING.................................................8

6.1. Change max power.........................................................................................9

7. HOPPING PARAMETER.....................................................................................10

7.1. Change BB-hopping on................................................................................12

7.2. Change RF-hopping on.................................................................................13

8. CHANNEL CONFIGURATION...........................................................................14

8.1. Change channel configuratio........................................................................15

System Group


3 (21)

8.1.1. Cell broadcast channel configuration.............................................15

9. LAPD LINK HANDLING.....................................................................................17

9.1. Check LAPD links speed..............................................................................17

9.2. Block LAPD links.........................................................................................17

10. CHECK THE SW VERSION OF BSC SW-PACKAGE......................................17

11. LINE EDITOR FUNCTIONS................................................................................18

12. ZEF?.......................................................................................................................20

13. ZEQ?......................................................................................................................21

14. ZER?......................................................................................................................22

System Group


4 (21)

1. INTRUDUCTION

This documet includes BSC basic commands for berginners.

BSC SW S7.17 was in used. (BSC-MML commands may vary between different BSC SW version.)

In example has used BCF=57, BTS=66, TRX-1 and 2.

If you like to get more inforamtion, please look from NED, BSC S7:2.6 command reference manual. NED is a program package designed for the retrieval, viewing, and printing of the electronic Nokia documents. As a whole, NED consists of the system documentation, the NED viewer and the Model.

At the beginning of an MML session, the user enters a user identification (= USER ID) and his password.

START Press any key.

USER ID\ PASSWORD

Give user identification and password.

ENTER USERNAME <SYSTEM

ENTER PASSWORD <*****

WELCOME TO THE DX200-SERIES DIALOGUE

DIALOGUE DESTINATION <

(or MAIN LEVEL COMMAND < > if user have direct connection)

If you want a list of the destinations on the screen, type a question mark:

DIALOGUE DESTINATION < ?

OMC OMC_CAM 1999-02-25 17:13:01

DIALOGUE DESTINATIONS

? ............... DISPLAY MENU ?SYSTEM NAME .... MENU OF O&M AREA L> .............. LOCAL SYSTEM HLR_38424> .... CMBLEY BSC1> ......... CMBLEY BSC2> ......... CMBLEY BSC3> ......... CMBLEY MSC038103> .... CMBRLY BSC4> ......... CAMBERLEY BSC5> ......... CMBLEY END> ............ END DIALOGUE

DIALOGUE DESTINATION < BSC2>

System Group


5 (21)

The following is displayed on the screen:

MAIN LEVEL COMMAND < >

<?

MAIN LEVEL

? ..... DISPLAY MENU

A ..... ALARM SYSTEM ADMINISTRATION

C ..... ROUTING STATE ADMINISTRATION

D ..... SYSTEM SUPPORT AND COMMUNICATION

E ..... CELLULAR RADIO NETWORK ADMINISTRATION

I ..... I/O SYSTEM ADMINISTRATION

N ..... SS7 NETWORK ADMINISTRATION

O ..... SUPPLEMENTARY SS7 NETWORK ADMINISTRATION

Q ..... O&M NETWORK ADMINISTRATION

R ..... ROUTING ADMINISTRATION

T ..... TRAFFIC ADMINISTRATION

U ..... UNIT ADMINISTRATION

W ..... SYSTEM CONFIGURATION ADMINISTRATION

Y ..... SYSTEM SUPERVISION

Z; .... END DIALOGUE

Give the command either directly or step by step in stages.

More information 2.6 Command reference manual in NED. Look at it, please.

TERMINATION OF REMOTE SESSION

In the following, the above example is continued till the end of the remote session:

< Z;

MAIN LEVEL COMMAND < >

< Z;

END OF DIALOGUE AT SELECTED DESTINATION

DIALOGUE DESTINATION < END>

END OF DIALOGUE SESSION

System Group


6 (21)

2. OUTPUT RADIO NETWORK CONFIGURATION

Check the status of the BCF/BTS/TRX:

ZEEI:BCF=57;

E P B F T R C D-CHANNEL ADM OP R ET- BCCH/CBCH/ R E S O&M LINK BUSY LAC CI STA STATE FREQ T PCM ERACH X F U NAME ST HR FR===================== === ====== ==== == ==== =========== = = = ===== == === ===

BCF-057 DE34/DF34 U WO 3 OMU57 WO 00004 02066 BTS-066 U WO 0 0 STARRMINI TRX-001 U WO 699 0 57 MBCCHC 3 TRX-002 U WO 745 0 57 3

3. ALARMS HANDLING

3.1. List Alarms Currently On

Check the active alarms using:

ZEOL:57;

BTS ALARM LISTING

BSC2 BCF-057 ENVIR 1999-01-15 11:11:05.61 * ALARM (11000) 7870 CABINET DOOR OPEN 00H 00H 00H 4BH 01H 00H

3.2. List Alarm History

Examples

List the alarm history collected after January 02, 1999 at 14:00

ZEOH:1999-01-02,14-00-00:BCF=57;

List the history of alarm 7870 collected today.

ZEOH::NR=7870;

System Group


7 (21)

4. SW PACKAGE HANDLING

4.1. List SW package of BCF

ZEWO:57;

DX 200 BSC2 1999-01-15 11:12:03

BCF STATUS PACKAGE-ID VERSION SUBDIR STATE-----------------------------------------------------------------------

BCF-057 NW DE34/DF34 BU DF30_A51 3.0-10 /PACK_14 DEFAULT (DEFAULT=in use) FB

4.2. Attach Software Package To BCF

The command executes the background downloading to the non-volatile memory of the BCF.

ZEWA:57:NW:DF40_A51;

4.3. Activate BCF software package

The command is used for activating and restarting the BCF with the attached software package.

ZEWV:57:NW;THIS COMMAND CUTS ALL ONGOING CALLS IN THE RESETED BTS SITECONFIRM COMMAND EXECUTION: Y/N ? YSOFTWARE PACKAGE ACTIVATEDBCF NUMBER RESET REASON FOR DENIAL---------------------------------------------------------BCF-057 STARTED

ZEWO:57;

BCF STATUS PACKAGE-ID VERSION SUBDIR STATE-----------------------------------------------------------------------BCF-057 NW DF40_A51 4.0-10 /PACK_13 DEFAULT (default = in use) DE34/DF34 BU DF30_A51 3.0-10 /PACK_14 FB

Fastest way to take new SW in use:

Block OMU LAPD link (DTC:OMU57:,BL;) (background downloading can not start)Attach Software Package ZEWA:57:NW:DF40_A51;Unblock a LAPD link (DTC:OMU57:,BL;)Activate BCF software package: ZEWV:57:NW;

System Group


8 (21)

5. CHANGE BCF, BTS AND TRX STATE

5.1. Locking the BCF, BTS, TRX and Timeslot

ZEFS:57:L; (lock BCF) ZEQS:BTS=66:L; (lock BTS) ZERS:BTS=66,TRX=1:L; (lock TRX) ZERS:BTS=66,TRX=1,CH=1&&4:L; (lock the RTSLs 1-4 in TRX number 1)

DX 200 BSC2 1999-01-25 11:27:14RADIO NETWORK CONFIGURATION IN BSC: E P B F T R C D-CHANNEL ADM OP R ET- BCCH/CBCH/ R E S O&M LINK BUSY LAC CI STA STATE FREQ T PCM ERACH X F U NAME ST HR FR===================== === ====== ==== == ==== =========== = = = ===== == === ===

BCF-057 DE34/DF34 L BL-USR 3 OMU57 WO 00004 02066 BTS-066 L BL-USR 0 0 STARRMINI TRX-001 L BL-USR 699 0 57 MBCCHC 3 TRX-002 L BL-USR 745 0 57 3

Unlock timeslots, TRX, BTS and BCF

ZERS:BTS=66,TRX=1,CH=1&&4:U; (unlock the RTSLs 1-4 in TRX 1) ZERS:BTS=66,TRX=1:U; (unlock TRX) ZEQS:BTS=66:U; (unlock BTS) ZEFS:57:U; (unlock BCF)

5.2. Forced Handover

With this parameter you force handovers in order to clear the traffic in the BTS or TRX.

BTS: ZEQS:BTS=66:L:FHO;

TRX: ZERS:BTS=66,TRX=1:L:FHO;

6. POWER CONTROL PARAMETER HANDLING

Output the power control parameters:

ZEUO:BTS=66;

LOADING PROGRAM VERSION 7.8-0

DX 200 BSC2 1999-01-25 11:28:04

POWER CONTROL PARAMETERS OFBTS-066 STARRMINI

POWER CTRL ENABLED ......... Y POWER CONTROL INTERVAL ..... 02 sBS TX PWR MIN ....PEAK PWR - 30 dB BS TX PWR MAX ....PEAK PWR - 14 dB

System Group


9 (21)

POWER INCR STEP SIZE ....... 4 dB POWER RED STEP SIZE ........ 2 dBPOWER DECR LIMIT BAND 0 .... 38 dB POWER DECR LIMIT BAND 1 .... 38 dBPOWER DECR LIMIT BAND 2 .... 38 dB POWER DECR QUAL FACTOR ..... 1ALA ENABLED ................ N MIN INT BETWEEN ALA ........ 10 sPOWER LIMIT ALA ............ 6 dB

PC AVERAGING LEV DL WINDOW SIZE ............ 04 WEIGHTING .... 1PC AVERAGING LEV UL WINDOW SIZE ............ 04 WEIGHTING .... 1PC AVERAGING QUAL DL WINDOW SIZE ............ 01 WEIGHTING .... 1PC AVERAGING QUAL UL WINDOW SIZE ............ 01 WEIGHTING .... 1

PC UPPER THRESHOLDS QUAL DL RX QUAL .. < 0.2% PX .. 32 NX .. 32PC UPPER THRESHOLDS QUAL UL RX QUAL .. < 0.2% PX .. 32 NX .. 32PC LOWER THRESHOLDS QUAL DL RX QUAL .. 0.8% - 1.6% PX .. 03 NX .. 04PC LOWER THRESHOLDS QUAL UL RX QUAL .. 0.8% - 1.6% PX .. 03 NX .. 04PC LOWER THRESHOLDS QUAL144 RX QUAL .. 0.8% - 1.6% PX .. 03 NX .. 04

PC UPPER THRESHOLDS LEV DL RX LEVEL .. - 70 dBm PX .. 01 NX .. 01PC UPPER THRESHOLDS LEV UL RX LEVEL .. - 70 dBm PX .. 01 NX .. 01PC LOWER THRESHOLDS LEV DL RX LEVEL .. - 85 dBm PX .. 01 NX .. 01PC LOWER THRESHOLDS LEV UL RX LEVEL .. - 85 dBm PX .. 01 NX .. 01

COMMAND EXECUTED

6.1. Change max power

bs tx pwr max, PMAX = decimal numberWith this parameter you identify the maximum transmission power of the BTS as an attenuation from the peak power of the TRX. The possible attenuation values range from 0 to 30 dB with a step size of 2 dB. The value of the parameter must be smaller than or equal to the value of the parameter PMIN.

ZEUG:BTS=66:PMAX=0;

DX 200 BSC2 1999-01-25 11:28:30

POWER CONTROL GENERAL PARAMETERS OFBTS-066 STARRMINI

POWER CTRL ENABLED ......... Y POWER CONTROL INTERVAL ..... 02 sBS TX PWR MIN ....PEAK PWR - 30 dB BS TX PWR MAX ....PEAK PWR - 00 dBPOWER INCR STEP SIZE ....... 4 dB POWER RED STEP SIZE ........ 2 dBPOWER DECR LIMIT BAND 0 .... 38 dB POWER DECR LIMIT BAND 1 .... 38 dBPOWER DECR LIMIT BAND 2 .... 38 dB POWER DECR QUAL FACTOR ..... 1ALA ENABLED ................ N MIN INT BETWEEN ALA ........ 10 sPOWER LIMIT ALA ............ 6 dB

(Change min power, ZEUG:BTS=66:PMAX=30;)

7. HOPPING PARAMETER

Check the hopping parameter:

ZEQO:BTS=66:ALL; (Using ZEQO:BTS=66; only hopping parameters)

BTS PARAMETERS :================

System Group


10 (21)

BCF-057 BTS-066 STARRMINI -------------------------------------BTS ADMINISTRATIVE STATE ... UNLOCKEDBTS OPERATIONAL STATE ...... BL-RSTBTS BACKGROUND DATA STATE .. NOT DEFINED

CELL IDENTITY............................(CI)..... 02066FREQUENCY BAND IN USE....................(BAND)... DCS

BS IDENTITY CODE.........................(BSIC)

NETWORK COLOUR CODE...................(NCC).... 3 BACKGROUND NETWORK COLOUR CODE........(BNCC)... -

BTS COLOUR CODE.......................(BCC).... 3 BACKGROUND BTS COLOUR CODE............(BBCC)... -

LOCATION AREA ID.........................(LAI) MOBILE COUNTRY CODE...................(MCC).... 234 MOBILE NETWORK CODE...................(MNC).... 15 LOCATION AREA CODE....................(LAC).... 00004

BTS HOPPING MODE.........................(HOP).... NBACKGROUND BTS HOPPING MODE..............(BHOP)... - UNDERLAY BTS HOPPING MODE................(UHOP)... NBACKGROUND UNDERLAY BTS HOPPING MODE.....(BUHOP).. -

MOBILE ALLOCATION FREQUENCY LIST......(MAL).... 25 BACKGROUND MOBILE ALLOC FREQ LIST.....(BMAL)... - UNDERLAY MOBILE ALLOC FREQ LIST.......(UMAL)... - BG UNDERLAY MOBILE ALLOC FREQ LIST....(BUMAL).. -

HOPPING SEQUENCE NUMBER 1.............(HSN1)... 0 BACKGROUND HOPPING SEQUENCE NUMBER 1..(BHSN1).. - HOPPING SEQUENCE NUMBER 2.............(HSN2)... 0 BACKGROUND HOPPING SEQUENCE NUMBER 2..(BHSN2).. - UNDERLAY HOPPING SEQUENCE NUMBER......(UHSN)... 0 BG UNDERLAY HOPPING SEQUENCE NUMBER...(BUHSN).. -

CELL BARRED..............................(BAR).... NCALL REESTABLISHMENT ALLOWED.............(RE)..... NEMERGENCY CALL RESTRICTED................(EC)..... NPLMN PERMITTED...........................(PLMN)... 03NOT ALLOWED ACCESS CLASSES...............(ACC).... -ADJACENCY ON OTHER BAND..................(DBC).... N DIRECTED RETRY USED......................(DR)..... N INTELLIGENT DIRECTED RETRY USED..........(IDR).... N CELL TYPE................................(CTY).... GSMMIN TIME LIMIT DIRECTED RETRY............(MIDR)... 0MAX TIME LIMIT DIRECTED RETRY............(MADR)... 5DIRECTED RETRY METHOD....................(DRM).... 0

CELL RESELECT HYSTERESIS.................(HYS).... 04 dBMS TXPWR MAX CCH.........................(TXP).... 30 dBmRXLEV ACCESS MIN.........................(RXP)....-105 dBmRADIO LINK TIMEOUT.......................(RLT).... 20 SACCH FRAMESPOWER OFFSET.............................(PO)..... 00 dB

MAX QUEUE LENGTH.........................(MQL).... 050 %TIME LIMIT CALL..........................(TLC).... 10 SECONDSTIME LIMIT HANDOVER......................(TLH).... 05 SECONDSQUEUE PRIORITY USED......................(QPU).... Y QUEUEING PRIORITY CALL................(QPC).... 10 QUEUEING PRIORITY URGENT HANDOVER.....(QPH).... 09 QUEUEING PRIORITY NON-URGENT HANDOVER.(QPN).... 09MS PRIORITY USED.........................(MPU).... Y

NBR OF BLOCKS FOR ACCESS GRANT MSG.......(AG)..... 01NBR OF MULTIFRAMES.......................(MFR).... 02TIMER FOR PERIODIC MS LOCATION UPDATING..(PER).... 00.5 HOURSALLOW IMSI ATTACH DETACH.................(ATT).... Y

System Group


11 (21)

C/N THRESHOLD............................(CNT).... 00 dB (NOT USED)AVERAGING PERIOD.........................(AP)..... 06BOUNDARY 0...............................(BO0)....-110 dBmBOUNDARY 1...............................(BO1)....-105 dBmBOUNDARY 2...............................(BO2)....-100 dBmBOUNDARY 3...............................(BO3)....-095 dBmBOUNDARY 4...............................(BO4)....-090 dBmBOUNDARY 5...............................(BO5)....-047 dBm

DTX MODE.................................(DTX).... 2 (MS SHALL NOT USE DTX)BTS MEASURE AVERAGE......................(BMA).... 01MS TXPWR MAX.............................(PMAX)... 30 dBmMS TXPWR MIN.............................(PMIN)... 00 dBmMAX NUMBER OF RETRANSMISSION.............(RET).... 04MAX NUMBER OF REPETITION.................(NY1).... 05NUMBER OF SLOTS SPREAD TRANS.............(SLO).... 10SMS CB USED..............................(CB)..... NBTS LOAD THRESHOLD.......................(BLT).... 070 %MS MAX DISTANCE IN CALL SETUP............(DMAX)... 255 (NO REJECTION)TRX PRIORITY IN TCH ALLOCATION...........(TRP).... 0TCH RATE INTRA-CELL HANDOVER.............(TRIH)... 0 (NO CONSTRAINTS)LOWER LIMIT FOR FR TCH RESOURCES.........(FRL).... 100 %UPPER LIMIT FOR FR TCH RESOURCES.........(FRU).... 0 %NEW ESTABLISHMENT CAUSES SUPPORT.........(NECI)... NRADIUS EXTENSION.........................(EXT).... 00 km (NORMAL CELL)MULTIBAND CELL REPORTING.................(MBR).... 1EARLY SENDING INDICATION.................(ESI).... YC2 RESELECTION PARAMETERS: CELL RESELECTION PARAMETER INDEX......(PI)..... N CELL BARR QUALIFY.....................(QUA).... N CELL RESELECT OFFSET..................(REO).... 0 dB TEMPORARY OFFSET......................(TEO).... 0 dB PENALTY TIME..........................(PET).... 20 s

TRUNK RESERVATION USED...................(TR)..... N LIMIT FOR FREE TCHS......................(LIMIT).. 16TCHS RESERVED FOR PRIORITY SUBSCRIBERS...(TCRP)... 0RESTRICTED USE OF PRIORITY CHANNELS......(RUP).... YRESERVATION METHOD.......................(REM).... DYN

TRAFFIC TYPE TABLE 1 (GSM CALL SETUP) - 2 (MCN CALL SETUP) - 3 (GSM HANDOVER) - 4 (MCN HANDOVER) - 5 (PRIORITY CALL SETUP) - 6 (PRIORITY HANDOVER) - 7 - 8 - 9 - 10 -

ID. OF BCCH FREQUENCY LIST........(IDLE)... 0 (ADJACENT CELL LIST USED)BCCH ALLOC. USAGE FOR ACTIVE MS...(ACT).... ADJ (ADJACENT CELL LIST USED)

BTS HOPPING MODE..................(HOP).... NOT (NOT HOPPING)BACKGROUND BTS HOPPING MODE.......(BHOP)... - HOPPING SEQUENCE NUMBER 1......(HSN1)... 0 *) BACKGROUND HSN1................(BHSN1).. - HOPPING SEQUENCE NUMBER 2......(HSN2)... 0 *) BACKGROUND HSN2................(BHSN2).. - MAIO OFFSET....................(MO)..... 0 *) BACKGROUND MAIO OFFSET.........(BMO).... - MAIO STEP......................(MS)..... 1 *) BACKGROUND MAIO STEP...........(BMS).... - MOBILE ALLOCATION FREQ LIST....(MAL).... 25 *) BACKGROUND MA FREQ LIST........(BMAL)... -

UNDERLAY BTS HOPPING MODE.........(UHOP)... NOT (NOT HOPPING)BG UNDERLAY BTS HOPPING MODE......(BUHOP).. - UNDERLAY HOP SEQ NUMBER........(UHSN)... 0 *)

System Group


12 (21)

BG UNDERLAY HOP SEQ NUMBER.....(BUHSN).. - UNDERLAY MAIO OFFSET...........(UMO).... 0 *) BG UNDERLAY MAIO OFFSET........(BUMO)... - UNDERLAY MAIO STEP.............(UMS).... 1 *) BG UNDERLAY MAIO STEP..........(BUMS)... - UNDERLAY MA FREQUENCY LIST.....(UMAL)... - *) BG UNDERLAY MA FREQUENCY LIST..(BUMAL).. -

MAIO VALUES PER RADIO TIMESLOT:

OVERLAY TRXS: ADM. OP. STATE STATE FREQ RTSL0 RTSL1 RTSL2 RTSL3 RTSL4 RTSL5 RTSL6 RTSL7TRX-001 U WO 699 BCCHTRX-002 U WO 745

THERE IS NO UNDERLAY TRX UNDER BTS

*) NOT RELEVANT IN THIS HOPPING MODE

HSCSD TCH CAPACITY MINIMUM...............(HTM).... 100 %HSCSD CELL LOAD UPPER LIMIT..............(HCU).... 100 %HSCSD CELL LOAD LOWER LIMIT..............(HCL).... 100 %HSCSD REGULAR CELL LOAD UPPER LIMIT......(HRCU)... 100 %HSCSD UPGRADE GUARD TIME.................(HUT).... 0 sHSCSD DOWNGRADE GUARD TIME...............(HDT).... 0 sHSCSD UPGRADE GAIN.......................(HUG).... 0 %HSCSD MINIMUM EXHAUST....................(HME).... 1

COMMAND EXECUTED

7.1. Change BB-hopping on

ZEQE:BTS=66:HOP=BB, HSN1=15,|HSN2=35; before that BCF (ZEFS:57:L;) and BTS (ZEQS:BTS=66:L;) have to be locked, random RF hopping, HSN1=15 and HSN2=35(BCF lock is not needed anymore after S8))


EXECUTION STARTED

BCF-057 BTS-066 STARRMINI -------------------------------------BTS ADMINISTRATIVE STATE ... LOCKEDBTS OPERATIONAL STATE ...... BL-USRBTS BACKGROUND DATA STATE .. NOT DEFINED






BTS HOPPING MODE.........................(HOP).... BBBACKGROUND BTS HOPPING MODE..............(BHOP)... -

System Group


13 (21)

UNDERLAY BTS HOPPING MODE................(UHOP)... NBACKGROUND UNDERLAY BTS HOPPING MODE.....(BUHOP).. -



7.2. Change RF-hopping on

ZEQE:BTS=66:HOP=RF,HSN1=0,|HSN2=0; before that BCF (ZEFS:57:L;) and BTS (ZEQS:BTS=66:L;) have to be locked, (cyclic BB-hop, HSN1=HSN2=0)

BCF-057 BTS-066 STARRMINI -------------------------------------BTS ADMINISTRATIVE STATE ... LOCKEDBTS OPERATIONAL STATE ...... BL-USRBTS BACKGROUND DATA STATE .. NOT DEFINED






BTS HOPPING MODE.........................(HOP).... RFBACKGROUND BTS HOPPING MODE..............(BHOP)... - UNDERLAY BTS HOPPING MODE................(UHOP)... NBACKGROUND UNDERLAY BTS HOPPING MODE.....(BUHOP).. -



Check used MAL list:

ZEBI:25;

EXECUTION STARTED

System Group


14 (21)

MOBILE ALLOCATION FREQUENCY LIST - 25 BAND ... DCSFREQUENCIES : 529 596 727 856 ATTACHED AS MOBILE ALLOCATION FREQUENCY LIST TO BTS: 66 STARRMINI

If there is not any MAL attached, attach BTS-66 to mobile allocation frequency list 25

ZEQA:BTS=66:MAL=25;

8. CHANNEL CONFIGURATION

ZERO:BTS=66; Check used channel configuration

ADM.STATE OP.STATE --------------------------------------BCF-057 UNLOCKED WO BTS-066 STARRMINI UNLOCKED WO TRX-001 UNLOCKED WO

ETRX N TRA NORM HRS Y PREF N

FREQ 699 TSC 3 FRT 0 (REGULAR) LEV N (NOT USED)BFREQ - BTSC - BFRT - BLEV -

DAL N (NOT USED)BDAL N (NOT USED)

SIGN 0

D-CH TELECOM LINK SET 80 FU157

RTSL PCM-TSL SUB_TSL TYPE I.LEV ADM.STATE OP.STATE CH.STATUS------------------------------------------------------------------------------ 0 57 - MBCCHC - UNLOCKED WO 1 57- 1 1 TCHF 0 UNLOCKED WO ID 2 57- 1 2 TCHF 0 UNLOCKED WO ID 3 57- 1 3 TCHF 0 UNLOCKED WO ID 4 57- 2 0 TCHF 0 UNLOCKED WO ID 5 57- 2 1 TCHF 0 UNLOCKED WO ID 6 57- 2 2 TCHF 0 UNLOCKED WO ID 7 57- 2 3 TCHF 0 UNLOCKED WO ID

TRANSCEIVER HAS NO INTERFERING CELLS

ADM.STATE OP.STATE --------------------------------------BCF-057 UNLOCKED WO BTS-066 STARRMINI UNLOCKED WO TRX-002 UNLOCKED WO

ETRX N TRA NORM HRS Y PREF N

FREQ 745 TSC 3 FRT 0 (REGULAR) LEV N (NOT USED)BFREQ - BTSC - BFRT - BLEV -

DAL N (NOT USED)BDAL N (NOT USED)

MA FREQUENCY LIST 25 SIGN 0MA FREQUENCY LIST (SUPER) -D-CH TELECOM LINK SET 144 FU257

RTSL PCM-TSL SUB_TSL TYPE I.LEV ADM.STATE OP.STATE CH.STATUS------------------------------------------------------------------------------ 0 57- 3 0 TCHD 0 UNLOCKED WO ID ID 1 57- 3 1 TCHD 0 UNLOCKED WO ID ID

System Group


15 (21)

2 57- 3 2 TCHD 0 UNLOCKED WO ID ID 3 57- 3 3 TCHD 0 UNLOCKED WO ID ID 4 57- 4 0 TCHD 0 UNLOCKED WO ID ID 5 57- 4 1 TCHD 0 UNLOCKED WO ID ID 6 57- 4 2 TCHD 0 UNLOCKED WO ID ID 7 57- 4 3 TCHD 0 UNLOCKED WO ID ID

TRANSCEIVER HAS NO INTERFERING CELLS

COMMAND EXECUTED

8.1. Change channel configuration

ZERM:BTS=66,TRX=1:CH0=MBCCH,CH1=SDCCH;

Before modifications TRX have to be locked. (ZERS:BTS=66,TRX=1:L;)Note ! If you have hopping in use you have to lock BTS first and then TRX and....

TRX unlock and now you have new configuration in use. (ZERS:BTS=66,TRX=2:U;)

8.1.1.Cell broadcast channel configuration

ZERS:BTS=66,TRX=1:L;ZERM:BTS=66,TRX=1:CH0=MBCCH,CH1=SDCCB;

Cell broadcast short message service (SMS CB) is allowed to be used in the cell.

ZEQM:BTS=66:CB=Y;

EXECUTION STARTED

MISCELLANEOUS PARAMETERS MODIFY COMPLETED:==========================================

BCF-057 BTS-066 STARRMINI -------------------------------------BTS ADMINISTRATIVE STATE ... UNLOCKEDBTS OPERATIONAL STATE ...... WOBTS BACKGROUND DATA STATE .. NOT DEFINED

DTX MODE.................................(DTX).... 2 (MS SHALL NOT USE DTX)BTS MEASURE AVERAGE......................(BMA).... 01MS TXPWR MAX.............................(PMAX)... 30 dBmMS TXPWR MIN.............................(PMIN)... 00 dBmMAX NUMBER OF RETRANSMISSION.............(RET).... 04MAX NUMBER OF REPETITION.................(NY1).... 05NUMBER OF SLOTS SPREAD TRANS.............(SLO).... 10SMS CB USED..............................(CB)..... YBTS LOAD THRESHOLD.......................(BLT).... 070 %MS MAX DISTANCE IN CALL SETUP............(DMAX)... 255 (NO REJECTION)TRX PRIORITY IN TCH ALLOCATION...........(TRP).... 0TCH RATE INTRA-CELL HANDOVER.............(TRIH)... 0 (NO CONSTRAINTS)LOWER LIMIT FOR FR TCH RESOURCES.........(FRL).... 100 %UPPER LIMIT FOR FR TCH RESOURCES.........(FRU).... 0 %NEW ESTABLISHMENT CAUSES SUPPORT.........(NECI)... NRADIUS EXTENSION.........................(EXT).... 00 km (NORMAL CELL)MULTIBAND CELL REPORTING.................(MBR).... 1EARLY SENDING INDICATION.................(ESI).... YC2 RESELECTION PARAMETERS:

System Group


16 (21)

CELL RESELECTION PARAMETER INDEX......(PI)..... N CELL BARR QUALIFY.....................(QUA).... N CELL RESELECT OFFSET..................(REO).... 0 dB TEMPORARY OFFSET......................(TEO).... 0 dB PENALTY TIME..........................(PET).... 20 s

Display all active messages within BTS 66 in long format.

ZECP:BTS=66:LONG;

ALL ACTIVE MESSAGES WITHIN THE BTS-066 STARRMINI

NO ACTIVE CB MESSAGES WITHIN THE BTS

COMMAND EXECUTED

Check all created messaged ZECP; or create your own ZECA Or ask it from you tutor)

Activate message with message index 2 for BTS 66,

ZECS:2:BTS=66:;


DX 200 BSC2 1999-01-25 12:05:26 PAGE 1

MESSAGE NO. 2 ACTIVATION

BTS NO. BTS NAME STATEBTS-066 STARRMINI OK

ZECP:N BTS=66:LONG;

ALL ACTIVE MESSAGES WITHIN THE BTS-066 STARRMINI

MESSAGE INDEX : 2MESSAGE IDENTIFIER : 50MESSAGE CODE : 50GEOGRAPHICAL SCOPE : CELL WIDE, NORMAL CODING GROUP : 0000LANGUAGE : ENGLISH REPETITION RATE : 4

MESSAGE BROADCASTED 0 TIMES

LIVE IS WONDERFUL............................................................................................................................................

9. LAPD LINK HANDLING

9.1. Check LAPD links speed

ZDSB:NAME=OMU57;ZDS? PRIMARY RATE ACCESS D-CHANNEL DATA HANDLING COMMAND

INTERROGATING BASE STATION CONTROLLER D-CHANNEL DATA EXT SUB TERM LOG LOG INTNAME NUM SAPI TEI BR PCM-TSL-TSL UNIT TERM FUNC UNIT TERM PCM-TSL----- --- ---- --- -- ----------- ----------------- ---------- -------OMU57 79 62 1 64 57-31 BCSU-3 1 4 4160H 36 17-04

ZDSB:NAME=FU157;

System Group


17 (21)

INTERROGATING BASE STATION CONTROLLER D-CHANNEL DATA EXT SUB TERM LOG LOG INTNAME NUM SAPI TEI BR PCM-TSL-TSL UNIT TERM FUNC UNIT TERM PCM-TSL----- --- ---- --- -- ----------- ----------------- ---------- -------FU157 80 0 1 64 57-30 BCSU-3 1 18 4160H 50 17-18

ZDSB:NAME=FU257;INTERROGATING BASE STATION CONTROLLER D-CHANNEL DATA EXT SUB TERM LOG LOG INTNAME NUM SAPI TEI BR PCM-TSL-TSL UNIT TERM FUNC UNIT TERM PCM-TSL----- --- ---- --- -- ----------- ----------------- ---------- -------FU257 144 0 2 64 57-29 BCSU-3 1 19 4160H 51 17-19

9.2. Block LAPD links

ZDTC:FU157:,BL;MODIFYING D-CHANNEL WORKING STATE

EXTNAME NUM D-CHANN PCM-TSL OLD STATE NEW STATE----- --- ------- ----------- --------- ---------FU157 80 P 57-30 WO-EX BL-US

10. CHECK THE SW VERSION OF BSC SW-PACKAGE

ZWQO:RUN;LOADING PROGRAM VERSION 5.9-0WORKING PACKAGES IN UNITS PAGE 1 MBA UNIT NAME STATUS PACKAGE_ID (REP-ID) 0 OMU S7101298 BU S7 7.17-0 1 4 MCMU-0 S7101298 BU S7 7.17-0 1 5 MCMU-1 S7101298 BU S7 7.17-0 1 30 BCSU-0 S7101298 BU S7 7.17-0 1 31 BCSU-1 S7101298 BU S7 7.17-0 1 32 BCSU-2 S7101298 BU S7 7.17-0 1 33 BCSU-3 S7101298 BU S7 7.17-0 1 34 BCSU-4 S7101298 BU S7 7.17-0 1 35 BCSU-5 S7101298 BU S7 7.17-0 1 36 BCSU-6 S7101298 BU S7 7.17-0 1 37 BCSU-7 S7101298 BU S7 7.17-0 1 38 BCSU-8 S7101298 BU S7 7.17-0 1

11. LINE EDITOR FUNCTIONS

CONTROL-A

Switches the editor from the INSERT mode to the REPLACE mode, or vice versa. In the REPLACE mode, the new characters you type are placed on top of the old characters, replacing them. In the INSERT mode, the old characters are moved forward, making room for the new ones.

CONTROL-B

CONTROL-B can be used for the same search functions in the command buffer as the 'up' arrow.

System Group


18 (21)

CONTROL-D

Moves the cursor one character to the left. Functions like the 'left' arrow.

CONTROL-F

Moves the cursor one character to the right. Functions like the 'right' arrow.

CONTROL-K

Language change key. Press the key to take the next language into use. The name of the language is displayed if there are several languages available.

CONTROL-P

Pressing CONTROL-P displays the following text on the screen:

<PAGE MODE> or <CONTINUOUS MODE>

In addition, all the characters read into the line buffer so far are displayed. PAGE MODE means that the text is displayed one screen at a time, and the system waits for a command to continue the output. The request for the continuation command is displayed on the bottom line of the screen.

CONTINUOUS MODE means that the text is output continuously without interruptions.

You can change the PAGE MODE output to CONTINUOUS MODE during the output when the program is waiting for the continuation command. It is not possible to change the CONTINUOUS MODE to PAGE MODE during the outputting.

CONTROL-Q

With this character, you can continue the output which you have interrupted by pressing CONTROL-S.

CONTROL-S

Interrupts the output until CONTROL-Q is pressed.

CONTROL-U

Deletes all the characters in the line buffer and the written characters on the screen.

CONTROL-7

Outputs the explanation for the error referred to by the latest general error message of the DX system.

CONTROL-Y Interrupts editing and returns the procedure to the command selection phase. If you press CONTROL-Y again, the procedure returns to the command class selection phase.

System Group


19 (21)

12. ZEF?

BASE CONTROL FUNCTION HANDLING COMMANDS


C: ..... CREATE BASE CONTROL FUNCTION

D: ..... DELETE BASE CONTROL FUNCTION

M: ..... MODIFY BASE CONTROL FUNCTION PARAMETERS

O: ..... OUTPUT BASE CONTROL FUNCTION PARAMETERS

S: ..... CHANGE BASE CONTROL FUNCTION ADMINISTRATIVE STATE

T: ..... SET BASE CONTROL FUNCTION OUTPUTS

R: ..... RESET BASE CONTROL FUNCTION

Z; ..... RETURN TO MAIN LEVEL

System Group


20 (21)

13. ZEQ?

BASE TRANSCEIVER STATION HANDLING IN BSC COMMANDS


C: ..... CREATE BTS

D: ..... DELETE BTS

A: ..... MODIFY MOBILE ALLOCATION FREQUENCY LIST USAGE PARAMETERS

B: ..... MODIFY BCCH FREQUENCY LIST USAGE PARAMETERS

E: ..... MODIFY BTS IDENTIFICATION PARAMETERS

F: ..... MODIFY CELL ACCESS PARAMETERS

G: ..... MODIFY RADIO LINK CONTROL DL PARAMETERS

H: ..... MODIFY QUEUEING PARAMETERS

J: ..... MODIFY CCH CONFIGURATION PARAMETERS

K: ..... MODIFY INTERFERENCE AVERAGING PARAMETERS

M: ..... MODIFY MISCELLANEOUS PARAMETERS

O: ..... OUTPUT BTS PARAMETERS

S: ..... CHANGE BTS ADMINISTRATIVE STATE

T: ..... MODIFY TRUNK RESERVATION PARAMETERS


System Group


21 (21)

14. ZER?

TRANSCEIVER DATA HANDLING COMMANDS


C: ..... CREATE TRANSCEIVER

D: ..... DELETE TRANSCEIVER

F: ..... CHANGE ABSOLUTE RADIO FREQUENCY NUMBER

M: ..... MODIFY TRANSCEIVER AND RADIO TIMESLOT PARAMETERS

T: ..... MODIFY TRANSCEIVER BINARY OUTPUTS

Y: ..... MODIFY TRANSCEIVER UNDERLAY-OVERLAY PARAMETERS

O: ..... OUTPUT TRANSCEIVER PARAMETERS

S: ..... CHANGE TRANSCEIVER AND RADIO TIMESLOT STATE


System Group

bsc commands for beginners

Documents

dialogue destination

bsc commands

system group

bsc2gt

gt

ned

hopping

trx