The INVALCO Model 4728 S&W Monitor, in conjunc-tion with a Model 4528EZ Detector and a Model CX-645Capacitance Probe is a continuous on-line monitor ofpercent water in a flowing crude oil emulsion stream.This unit displays percent of water in various ranges from0-5% up to and including 0-20% on a digital LCD indica-tor. In addition, the Model 4728 provides a 4-20 mAanalog output proportional to input range, and a field-adjusted, time-delayed, limit relay for valve control oralarming.The Model 4728 utilizes CMOS circuitry for low power con-sumption, high reliability, and wide temperature stability.

Features

Real-Time Display and Retransmission of S&W - Al-lows quick response to upset conditions for downstreamcontrols.Adjustable Delay of Relay Closure - Prevents nuisancealarms and actuator overload.Direct Analog Output from Model 4528EZ Detector - A4-20 mA signal is standard from the probe without theneed to include the Model 4728 monitor.NACE Adaptable - Can be modified for use in sour ser-vice.

Model 4728 Monitor and Model CX-645 Probe

Applications

LACT (Lease Automatic Custody Transfer) UnitsDetect and reroute oil that has been contaminated byexcess S&W.Pipeline LoadingMonitor transfer of petroleum/condensate products fromoffshore loading facilities.Dehydration EquipmentDetermine and enhance equipment efficiencies.Fuel Oil MonitoringDetermine contamination of fuel oil by condensation orother external factors before entry to engine.Storage and Treating FacilitiesMonitoring and early detection of undesirable conditionsas well as interface detection during de-watering of stor-age tanks.

Model 4728 Specifications

Power Supply18-28 Vdc @ 130 mA115/220 VacS&W Range0-5%, 0-10%, and 0-20% range options.

DisplayFour digit LCD with decimal point.

Analog Outputs4-20 mA, 2-wire internally powered or 4-20 mA, 3-wireexternally powered.

Relay OutputSPDT Relay, 10A, 250 Vac.1/2 Hp 250 Vac, 10A - 120 Vac resistive.1/3 Hp 120 Vac, 10A - 30 Vdc resistive.

Time Delay0 to 90 seconds adjustable in 10 second increments.Off-delay approximately 10% of on-delay time.

Temperature Range-20F to 160F (-20C to 70C).

EnclosuresNEMA 4X, weatherproof.NEMA 7, explosion-proof, Class I, Division 1, Groups Cand D.

Bulletin SSIS005

Oil/Water MonitorsModels 4528EZ & 4728 Monitors

Model CX-645 Probe

FMC INVALCO ! Fluid Control ! Stephenville, Texas 76401 ! Telephone: 254/968-2181 ! FAX 254/968-5709 ! Toll Free: 800/468-2526

Model 4728 Ordering Information

Model 4728 Dimensional SpecificationsInches (mm)

Note: Dimensions - Inches to the nearest tenth (millimeters to the nearest whole mm), each independently dimensioned from respectiveengineering drawings.

Model 4528EZ Detector and Model CX-645Probe

The Model 4528EZ Detector and Model CX-645 Probeprovide a direct analog (0-5 Vdc and 4-20 mA) output ofpercent emulsified water (as S&W) in the process stream.This signal is designed to be used externally by the Model4728 monitor or other control devices such as PLCs orRemote Terminal Systems.The probe is constructed of two concentric tubes. Wettedsurfaces are coated with a baked-on phenolic two-partepoxy. The inner tube is insulated from the outer tube byTeflon spacers and is electrically connected to a terminal

within the sensor housing. The internal element spacerscan be fitted with trimmer rods should it be necessary toadjust the base capacitance.The detector operates from a 8-28 Vdc regulated powersupply from within the associated monitor or customer-supplied source. All calibration and adjustments can beaccessed through the front panel for ease of use. TheModel 4528EZ detector offers the flexibility of a high orlow fail-safe. This fail-safe feature guarantees the qualityof the output signal from the detector chassis and willsense over- and under-range conditions as well as anopen or shorted probe.

Model CX-645 Capacitance Probe & Model 4528EZ Detector

Model CX-645 Capacitance Probe &Model 4528EZ Detector

Power Supply8-28 Vdc @ 130 mA

S&W Range Field Selectable0-5%, 0-10%, and 0-20%.

Measurement Accuracy1.0% of full scale.

Resolution/Sensitivity0.5% of full scale.

Probe MaterialA53 GrB Carbon Steel is standard.Stainless Steel available.

Probe FinishBaked-on phenolic two-part epoxy.

Probe Sizes/Length2 I.D. is 17 face-to-face.3 to 12 I.D. sizes are 32 face-to-face.

Detector/Probe Specifications

Process ConnectionsANSI RF or RTJ Flanges to 600# (all sizes) (others byspecial order).Threaded MNPT or Grooved (2 and 3).

Pressure RatingsAs per Flange selection, 1440 psig max. (Others by specialorder)NPT - 1440 psig max.Victualic grooved - 350 psig

Temperature Range-20F to 180F standard.-20F to 375F optional.ApprovalsUL/C-UL Explosion-proof certificate for Class I, Div. 1,Groups C and D or Class II, Groups E, F, and G hazard-ous locations.

Dimensions - CX-645 SpecificationsInches (mm)

*-20F to 180F dimension given. For -20F to375F dimension add 6.4.

Note: Dimensions - Inches to the nearest tenth (millimeters to thenearest whole mm), each independently dimensioned from respectiveengineering drawings.

1.25 FNPTConduitConnection

Element(Inner Plate)

Trimmer Rod(if needed)

Dimension A

Probe Body(Outer Plate)

Teflon Insulator

Dimension B

Model 4528EZExp. Housing

Typical Applications

Percent Water Indication and Set-Point ControlIn this application the adjustable alarm may be used tooperate a diverter valve should the water content exceeda preset percentage. Local indication is provided and ananalog output for other indication or control functions isavailable.

Percent Water RecordingIn this application the Model 4728 provides local readingon an LCD display and provides an analog output (4-20mA) to a standard recorder, PLC, or DCS System. Thisconfiguration is used to monitor and control Separatorand Heater-Treater efficiencies as well as other oil fieldand industrial applications.

CX-645 Capacitance Probe Ordering Information

Issue/Rev. 0.1 (2/04)4 SSIT042

The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications arecurrently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been changed and are no longer in effect.

FMC INVALCO Fluid Control Stephenville, TX 76401, Phone: 254/968-2181, FAX: 254/968-5709, Toll Free: 800/468-2526Printed in U.S.A. 6/05 FMC INVALCO All rights reserved.

www.fmcinvalco.com

Capacitance ProbeModel CX-645 &4528EZ Detector

Model 4728Oil/Water Monitor

FourConductor Cable Analog

Output

Solenoid

DiverterValve

Capacitance ProbeModel CX-645 &4528EZ Detector

Model 4728Oil/Water Monitor

FourConductor Cable

AnalogOutput

Recorder,PLC/DCSSystem

BS&W Probe, Ranges from 0-20% water - to be used with Model 4528EZ DetectorCX-645 PROBE MATERIAL: Carbon Steel

ll CODE PROBE BODY SIZEl 2 2 INCH I.D. x 17" FACE TO FACEl 3 3 INCH I.D. x 32" FACE TO FACEl 4 4 INCH I.D. x 32" FACE TO FACEl 6 6 INCH I.D. x 32" FACE TO FACEl 8 8 INCH I.D. x 32" FACE TO FACE l 10 10 INCH I.D. x 32" FACE TO FACEl l CODE END CONNECTIONSl l 00 SCREWED ENDS (to 3" only)l l 00 GROOVED ENDS/Victaulic (to 4" only)l l 00 150 LB ANSI RAISED FACEl l 30 300 LB ANSI RAISED FACEl l 60 600 LB ANSI RAISED FACE (SCH 80) (FOR 8" AND 10")l l 90 900 LB ANSI RAISED FACE and RING JOINT (SCH 160) (10")l l 05 150 LB ANSI RTJl l 35 300 LB ANSI RTJl l 65 600 LB ANSI RTJ (SCH 80) (FOR 8" AND 10")l l 95 900 LB ANSI RTJ (SCH 80)l l 115 1500 LB ANSI RTJ (SCH 160)l l l CODE MATERIAL AND TEMPERATURE OPTIONSl l l B STANDARD MATERIALS, A53B CARBON STEEL, -20-180 Fl l l H STANDARD MATERIALS/HIGH TEMP, -20 - 375 Fl l l S 316 STAINLESS STEEL MATERIALS, -20-180Fl l l T 316 STAINLESS STEEL/HIGH TEMP, -20 -375Fl l l l CODE CONNECTION STYLEl l l l S SCREWED CONNECTIONS, MNPTl l l l G VICTAULIC CONNECTIONS (GROOVED)l l l l F FLANGED CONNECTIONSl l l l l CODE OPENl l l l l P PHENOLIC COATING ( Interior )l l l l l l

Example: l l l l lCX - 645 - 3 60 - B F P = CX-645-360-BFP Choose one code selection from each option group to build model number.

The Model WCM 7300 is designed to provide the highestpossible sensitivity, resolution, and accuracy for water con-tent determination in crude oil, other hydrocarbons, or otherlow dielectric liquids from a max of 25% to levels below 1000parts per million (ppm). In oil and natural gas (condensate)production, water cut and S&W measurements are signifi-cantly improved with the WCM 7300 technology. Enhanceddigital signal processing and full product temperature com-pensation are two of the technological advancements utilizedby this device. Probe sizes from 2 through 12 are available.4-20 mA and 0-5 volt outputs are available for remote read-out. Water cut, process temperature or probe electrical valuecan be selected for viewing without removing conduletcover by use of a supplied magnet to operate an internalreed switch.

Product Temperature Compensation

The base dielectric constant (Dk) of oils can change withchanges in temperature. This can cause traditional moni-tors to change without a variance in water content. Forexample; for a 10F change, a typical curde oil may showa reading shift of as much as 0.1%, which normally wouldbe considered as water. The WCM 7300 measures prod-uct temperature and calculates a corrected cut reading,providing a true water or S&W cut at any temperature upto 160F.

Features

NACE Adaptable - Can be modified for use in sour service.

WCM 7300 Water Cut Monitor

Applications

LACT (Lease Automatic Custody Transfer) UnitsDetect and provide relay contact closure that can be usedto reroute oil that has excess S&W.Pipeline LoadingMonitor transfer of petroleum/condensate products fromloading facilities.Dehydration EquipmentDetermine and enhance equipment efficiencies, by moni-toring the product and indicating water content.Fuel Oil MonitoringDetermine contamination of fuel oil by condensation, orother external factors, before entry to engine.Storage and Treating FacilitiesMonitoring and early detection of undesirable conditionsas well as interface detection during de-watering of stor-age tanks.

Measurement/Monitor Specifications

Power Supply20-30 Vdc +/-10% @ nominal, 100 mA max.S&W Full Scale Range0-25%Field adjustable to 0-5%, 0-10%, etc.AccuracyIs defined as the variance observed between the 7300reading and the water grindout of the oil.Normal variances are:

+/-.05 from 0 to 5% water+/-.1 from 5 to 10% water+/-.15 from 10% to 15% water+/-.2 to .25 from 15 to 25% water

DisplaysOne line 16 character, alphanumeric LCD showing byselection:

Water CutProcess TemperatureProbe Electrical Value

Red/Green LED showing good oil, bad oil, or by passing,condition.

Bulletin SSIS003

Temperature CompensatedWater Cut MonitorEnergy Systems Model WCM 7300

FMC INVALCO ! Fluid Control ! Stephenville, Texas 76401 ! Telephone: 254/968-2181 ! FAX 254/968-5709 ! Toll Free: 800/468-2526

Pressure RatingsAs per Flange selection, 1440 psig max. (Others by specialorder)NPT - 1440 psig max.Victualic grooved - 350 psig

WCM 7300 Probe/Monitor Assemblies Ordering Information

WCM 7300 DimensionsInches (mm)

Note: Dimensions - Inches to the nearest tenth (millimeters to the nearest whole mm), each independently dimensioned from respectiveengineering drawings.

Issue/Rev. 0.1 (2/04)6 SSIT042

The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications arecurrently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been changed and are no longer in effect.

FMC INVALCO Fluid Control Stephenville, TX 76401, Phone: 254/968-2181, FAX: 254/968-5709, Toll Free: 800/468-2526Printed in U.S.A. 6/05 FMC INVALCO All rights reserved.

www.fmcinvalco.com

WCM WATER CUT MONITOR, DIGITAL, TEMPERATURE COMPENSATING, Ranges from 0-20% water 7300 PROBE MATERIAL: Carbon Steel

l

l CODE PROBE BODY SIZE

l 2 2 INCH I.D. x 17" FACE TO FACEl 3 3 INCH I.D. x 32" FACE TO FACEl 4 4 INCH I.D. x 32" FACE TO FACEl 6 6 INCH I.D. x 32" FACE TO FACEl 8 8 INCH I.D. x 32" FACE TO FACE

l l CODE END CONNECTIONSl l 00 SCREWED ENDS (to 3" only)l l 00 GROOVED ENDS/Victaulic (to 4" only)l l 00 150 LB ANSI RAISED FACEl l 30 300 LB ANSI RAISED FACEl l 60 600 LB ANSI RAISED FACE (SCH 80) (FOR 8" AND 10")l l 90 900 LB ANSI RAISED FACE and RING JOINT (SCH 160) (FOR 10")l l 05 150 LB ANSI RTJl l 35 300 LB ANSI RTJl l 65 600 LB ANSI RTJ (SCH 80) (FOR 8" AND 10")l l 95 900 LB ANSI RTJ (SCH 80)l l 115 1500 LB ANSI RTJ (SCH 160)

l l l CODE MATERIAL AND TEMPERATURE OPTIONS

l l l B STANDARD MATERIALS, A53B CARBON STEEL, -20-160Fl l l H STANDARD MATERIALS/HIGH TEMP, -20 - 375F l l l S 316 STAINLESS STEEL MATERIALS -20-160Fl l l T 316 STAINLESS STEEL/HIGH TEMP, -20 - 375F

l l l l CODE CONNECTION STYLE

l l l l S SCREWED CONNECTIONS, MNPTl l l l G VICTAULIC CONNECTIONS (GROOVED)l l l l F FLANGED CONNECTIONS

l l l l l CODE OPEN

l l l l l P Epoxyl l l l l l

Example: l l l l lWCM7300 - 4 60 - B F P = WCM7300 - 460 - BFP Choose one code selection from each option group to build model number and correct pricing.

1 - Consult factory for temperature compensation

Notes:

1

1

The Model WCM 7300E is designed to provide the highestpossible sensitivity, resolution, and accuracy for water con-tent determination in crude oil, other hydrocarbons, or otherlow dielectric liquids from a max of 25% to levels below 1000parts per million (ppm). In oil and natural gas (condensate)production, water cut and S&W measurements are signifi-cantly improved with the WCM 7300E technology. Enhanceddigital signal processing and full product temperature com-pensation are two of the technological advancements utilizedby this device. Water cut, process temperature or probeelectrical value can be selected for viewing without remov-ing condulet cover by use of a supplied magnet to oper-ate an internal reed switch.

Product Temperature Compensation

The base dielectric constant (Dk) of oils can change withchanges in temperature. This can cause traditional moni-tors to change without a variance in water content. Forexample; for a 10F change, a typical curde oil may showa reading shift of as much as 0.1%, which normally wouldbe considered as water. The WCM 7300 measures prod-uct temperature and calculates a corrected cut reading,providing a true water or S&W cut at any temperature upto 160F.

WCM 7300E Water Cut Monitor

Applications

LACT (Lease Automatic Custody Transfer) UnitsDetect and provide relay contact closure that can be usedto reroute oil that has excess S&W.Pipeline LoadingMonitor transfer of petroleum/condensate products fromloading facilities.Dehydration EquipmentDetermine and enhance equipment efficiencies, by moni-toring the product and indicating water content.Fuel Oil MonitoringDetermine contamination of fuel oil by condensation, orother external factors, before entry to engine.Storage and Treating FacilitiesMonitoring and early detection of undesirable conditionsas well as interface detection during de-watering of stor-age tanks.

Measurement/Monitor Specifications

Power Supply20-30 Vdc +/-10% @ nominal, 100 mA max.S&W Full Scale Range0-25%Field adjustable to 0-5%, 0-10%, etc.Sensitivity/Resolution.01% - 100 ppmAccuracyIs defined as the normal variance observed in the field be-tween the 7300 reading and the water grindout of the oil.These observed variance numbers are larger than the statedsensitivity/resolution of the WCM because the Dk of the oil inactual field operations is not constant but is continuouslychanging due to varying amounts of trace contaminents suchas chemicals, minerals, solution gas, etc. These cause smallchanges in the Dk which is independent of the water cut. TheWCM sees these changes and so indicates them. In thelaboratory the WCM easily detects and indicates changes of100 ppm, or less. This accuracy is seldom observed in thefield because of the reasons stated above. The accuracystatements shown are what is normally obtainable (based onmany, many installations) in the field and not on controlledtesting in a lab.Normal variances are:

+/-.05 from 0 to 5% water+/-.1 from 5 to 10% water+/-.15 from 10% to 15% water+/-.2 to .25 from 15 to 25% water

FMC INVALCO ! Fluid Control ! Stephenville, Texas 76401 ! Telephone: 254/968-2181 ! FAX 254/968-5709 ! Toll Free: 800/468-2526

Bulletin SSIS004

Temperature Compensated Water Cut Monitorwith Insertion ProbeEnergy Systems Model WCM 7300E

Features

Nace Adaptable - Can be modified for use in sourservice.

DisplaysOne line 16 character, alphanumeric LCD showing by selec-tion:

Water CutProcess TemperatureProbe Electrical Value

Red/Green LED showing good oil, bad oil, or by passing,condition.

Measurement/Monitor SpecificationsPressure RatingsAs per Flange selection, 1440 psig max. (Others by specialorder)NPT - 1440 psig max.Victualic grooved - 350 psig

Ordering InformationWCM INSERTION STYLE WATER CUT MONITOR, DIGITAL, TEMPERATURE COMPENSATING, Ranges from 0-20% water 7300E PROBE MATERIAL: Carbon Steel

l CODE PROBE BODY SIZE

l 2 2 INCH O.D.l 3 3 INCH O.D.l l CODE END CONNECTIONS

l l 00 SCREWED ENDS l l 00 150 LB ANSI RAISED FACEl l 30 300 LB ANSI RAISED FACEl l 60 600 LB ANSI RAISED FACE l l 90 900 LB ANSI RAISED FACE(SCH 80)l l 05 150 LB ANSI RTJl l 35 300 LB ANSI RTJl l 65 600 LB ANSI RTJl l 95 900 LB ANSI RTJ (SCH 80)l l 115 1500 LB ANSI RTJ (SCH 160)l l l CODE MATERIAL AND TEMPERATURE OPTIONS

l l l B STANDARD MATERIALS, A53B CARBON STEEL, -20-160Fl l l H STANDARD MATERIALS/HIGH TEMP, -20 - 375Fl l l S 316 STAINLESS STEEL MATERIALS -20-160Fl l l T 316 STAINLESS STEEL/HIGH TEMP, -20 - 375Fl l l l CODE CONNECTION STYLE

l l l l S SCREWED CONNECTIONS, MNPTl l l l G VICTAULIC CONNECTIONS (GROOVED)l l l l F FLANGED CONNECTIONSl l l l l CODE OPEN

l l l l l P Epoxyl l l l l l

Example: l l l l l

WCM7300E - 2 60 - B F P = WCM7300 - 260 - BFP

Choose one code selection from each option group to build model number and correct pricing.

Notes:1 - Consult Factory for temperature compensation factor.

1

1

WCM 7300 E Insertion ProbesOften it is more economical to use an insertion probe than an inline on large diameter Flow Lines. Not only is the initialcost less, but handling costs in the field are also greatly reduced.

Note: These dimensions are for the 2 probe.The 3 face to end would be 18 instead of 28

8.10

RE

F

5.38

RE

F

11.4

5 R

EF

28.0

0R

EF

5.38

RE

F

Issue/Rev. 0.1 (2/04)10 SSIT042

The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications arecurrently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been changed and are no longer in effect.

FMC INVALCO Fluid Control Stephenville, TX 76401, Phone: 254/968-2181, FAX: 254/968-5709, Toll Free: 800/468-2526Printed in U.S.A. 6/05 FMC INVALCO All rights reserved.

www.fmcinvalco.com

The INVALCO Model 2100 Net Oil Computer is used to determinenet oil, net water, BS&W content, and net gas produced in a welltest or similar operation.

Specifications

EnclosureNEMA 4X fiberglass with clear hinged door.Inner metal door allows easy access to wiring terminals andsupports user interface.MemoryBattery backed RAM memory storage of setup and data valuesfor 10 years.Power110-220 VAC 50-60 Hz fused at 2 ampre12 or 24 VDC fuse type Littlefuse @273002Inputs

Counts3 - dry contact (16Hz maximum frequency)3 - Pre-amp or photo pulser (10KHz maximum frequency)3 - pickup coil (10KHz maximum frequency)(Any combination of the count inputs can be configured= 3 meter inputs total)Count Accuracy +/-0.25% of input counts per unit volume.Temperature2 - dual thermistor probe inputs standard (LEMC #5507

probes)-20F to 150F standard+/-0.15F Accuracy

1 - probe for emulsion stream temperature averaging.1 - probe for gas stream temperature averaging.Optional higher temperature ranges available(32F - 212F or 60F - 240F)Analog1 - BS&W input scalable for 0-5 VDC, 1-5 VDC (0-

100%)1 - BS&W input scalable 4-20mA (0-100%)

Model 2100 Net Oil Computer

Features

Benefits

3 Meter InputsFour Line 20 Character Alpha Numeric DisplayJumper Selectable RS485 or RS232 Communication OptionFour 10 amp SPDT Dry Contact RelaysOne Megabyte of CMOS RAM Data Storage with BatteryBackup.

Measure BS&W, Total Water, Total Oil, Total GasEasy to Read - Even in Low Light ConditionsCommunicate Directly with SCADA SystemControl All Your Needed AccessoriesRetain All Important Data, Even if Power is Interrupted

Bulletin SSIS009

Net Oil Computer Specifications

Energy Systems Model 2100Net Oil Computer

1 - Gas pressure input 1-5 VDC or 4-20mADiscrete3 - Self powered dry contact closure inputs for externalmonitoring using Modbus Communication.1 - Self powered dry contact closure input used as systemreset integral with reset switch.

Outputs4 - relay NO or NC contacts 10 amp SPDT3 - relays used for volume pulse output(Net or Gross-tenths of a barrel or cubic foot)1 - relay for Alarm or Error indication/control12 or 24 VDC outputSerial Communication RS 232 three wire, or RS 485

five wire (Modbus RTU communication pro-tocol)User Interface

Screen - 4 line by 20 character vacuum Florissant display.4 - touch switches used to scroll through screens andchange values1 - toggle switch for resetFWD - (forward) - moves through displays in a forwarddirection.REV - (reverse) - moves through displays in a reversedirectionUP - increases values on screens where user interfaceis requiredDWN - (down) - decreases values or changes currentoption on screens where user interface is required.Reset - resets totals.

Optional external reset with dry contact usingterminal block input where Reset switch is ter-minated also.

FMC Energy Systems ! Fluid Control ! Stephenville, Texas 76401 ! Telephone: 254/968-2181 ! FAX 254/968-5709 ! Toll Free: 800/468-2526

Power Supply12 Vdc @ 130 mA for 0-5 Vdc output.24 Vdc required for 4-20 mA output.

S&W Range0-100%.

Detector/Probe Specifications

Process ConnectionsANSI RF or RTJ Flanges to 600# (all sizes) (others byspecial order).Threaded MNPT or Grooved (2 and 3).

Pressure RatingsAs per Flange selection, 1440 psig max. (Others by specialorder)NPT - 1440 psig max.Victualic grooved - 350 psigTemperature Range-20F to 180F standard.-20F to 375F optional.

Dimensions - CX-545 SpecificationsInches (mm)

*0F to 180F dimension given. For -20F to375F dimension add 6.4.

Note: Dimensions - Inches to the nearest tenth (millimeters to the nearest whole mm), each independently dimensioned from respective engineer-ing drawings.

Measurement Accuracy1.0%

Resolution/Sensitivity0.5%

Probe MaterialA53 GrB Carbon Steel is standard.Stainless Steel available.

Internal Probe FinishBaked-on phenolic two-part epoxy.

Probe Sizes/Length2 I.D. is 17 face-to-face.3 to 12 I.D. sizes are 32 face-to-face.

*

Model CX-545 Capacitance Probe & Model4528-100-IL Detector

Model CX-545 Capacitance Probe & Model 4528 Detector-100-ILModel 4528-100-IL Detector for CX-545 Probe 0-100% - P513604

FeaturesNACE Adaptable - Can be modified for use in sourservice.

Size Dim A Dim B Weight (lbs)2 INCH 17 (431 mm) 8.93" (227 mm) 203 INCH 17 (431 mm) 9.16" (233 mm) 40

CX-545 Capacitance Probe Ordering Information

Three-Phase System with Three Meters

CX-545 PROBE MATERIAL: Carbon Steelll CODE PROBE BODY SIZE - Consult Factory for larger sizesl 2 2 INCH I.D. x 17" FACE TO FACEl 3 3 INCH I.D. x 32" FACE TO FACEl 4 4 INCH I.D. X 17" FACE TO FACEl l CODE END CONNECTIONSl l 00 SCREWED ENDS (2" & 3" only)l l 00 GROOVED ENDS/Victaulic (2", 3" & 4" only)l l 00 150 LB ANSI RAISED FACEl l 30 300 LB ANSI RAISED FACEl l 60 600 LB ANSI RAISED FACE l l 90 900 LB ANSI RAISED FACE(SCH 80)l l 05 150 LB ANSI RTJl l 35 300 LB ANSI RTJl l 65 600 LB ANSI RTJ l l 95 900 LB ANSI RTJ (SCH 80)l l 115 1500 LB ANSI RTJ (SCH 160)l l l CODE MATERIAL AND TEMPERATURE OPTIONSl l l B STANDARD MATERIALS, A53B CARBON STEEL, -20 - 180 Fl l l H STANDARD MATERIALS/HIGH TEMP, -20 - 375 Fl l l S 316 STAINLESS STEEL MATERIALS -20 - 180 Fl l l T 316 STAINLESS STEEL/HIGH TEMP, -20 - 375Fl l l l CODE CONNECTION STYLEl l l l S SCREWED CONNECTIONS, MNPTl l l l G VICTAULIC CONNECTIONS (GROOVED)l l l l F FLANGED CONNECTIONSl l l l l CODE OPENl l l l l P PHENOLIC COATING ( Interior )l l l l l l

Example: l l l l lCX - 545 - 3 60 - B F P = CX-545-360-BFP Choose one code selection from each option group to build model number.

Issue/Rev. 0.1 (2/04)14 SSIT042

The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications arecurrently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been changed and are no longer in effect.

FMC INVALCO Fluid Control Stephenville, TX 76401, Phone: 254/968-2181, FAX: 254/968-5709, Toll Free: 800/468-2526Printed in U.S.A. 6/04 FMC INVALCO All rights reserved.

www.fmcinvalco.com