buckling and collapse of offshore pipes under combined
TRANSCRIPT
![Page 1: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/1.jpg)
Buckling and Collapse of Offshore Pipes under Combined Bending and External Pressure
JENS HAFSTAD 30.09.2020
![Page 2: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/2.jpg)
IntroductionIntroduction
Brief introduction to bifurcation buckling◦ Introductory example
Elastic ring buckling due to hydrostatic pressure
Collapse of offshore pipelines due to hydrostatic pressure◦ Timoshenko collapse formula
◦ Code treatment of collapse
Factors affecting collapse pressure
Collapse of offshore pipelines due to hydrostatic pressure and bending◦ Factors affecting collapse
◦ Collapse formula and pressure-moment interaction
![Page 3: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/3.jpg)
IntroductionSteel pipelines often form an important part of offshore developments
◦ As steel-catenary risers (SCR)
◦ Infield Flowlines – small size (<12 in), short distances of a few km
◦ Feeder line – medium size (6-20 in), longer distance (order of 100 km)
◦ Transmission (trunk) lines – large size ( up to 48 in) and long distances (e.g. Norway-UK 1200 km)
Need to be designed to withstand external loadings (pressure, bending, axial tension)
◦ Focus of this lecture is collapse due to externalpressure and bending
Infield flowline
Feeder line
Transmission line
![Page 4: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/4.jpg)
Pipeline limit statesLimit state (DNVGL-ST-F101) - a state beyond which the structure no longer satisfies the requirements
◦ serviceability limit state (SLS): A condition which, if exceeded, renders the pipeline unsuitable for normal operations
◦ ultimate limit state (ULS): A condition which, if exceeded, compromises the integrity of the pipeline
Local collapse of an offshore pipeline is characterized by the loss of roundness and gross deformation of the cross-section – ULS
![Page 5: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/5.jpg)
Deep-water pipeline collapseOil and gas exploration is moving towards deeper waters with future developments that may approach 3500-4000m
◦ Deep water: 300-1500 m, ultra deep-water: >1500 m (EIA)
Where (ultra) deep-water field developments are likely to take place:
◦ Gulf of Mexico (1800-2000 m)
◦ Brazilian Pre-Salt (excess of 2000 m)
◦ West Africa
Some trunklines are also installed or planned in ultra-deep waters
◦ Oman-India pipeline (planned) – up to 3500m
◦ South Stream pipeline – up to 2250m
The burst limit state (due to internal pressure) is usually the most critical loading in shallow water. For (ultra) deep-water the hydrostatic loading may become the dominant loading and critical design factor
◦ Pipeline installed without water filling experiences hydrostatic pressure without internal pressure to balance
![Page 6: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/6.jpg)
Trend towards deeper waters
![Page 7: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/7.jpg)
Introduction to bucklingA brief introduction to the buckling phenomenon will be given in the following
◦ An in-depth treatment requires a course in itself
Consider an infinite and perfectly round pipe loaded by hydrostatic pressure
◦ The primary (sometimes called fundamental or pre-buckling) solution is a uniform compression of the pipe
◦ At some load, this configuration becomes unstable and a different configuration becomes more energetically favourable – in the case of the pipe, this is (at least initially) an ovalization deformation
◦ Buckling is the process of changing (suddenly) from one configuration to the other
![Page 8: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/8.jpg)
The concept of stability• Assume that external loading is applied quasi-
statically to a structure. The structure will then deform while static equilibrium is maintained
• If at any load level a small disturbance is applied and the structure:
a) Oscillates about the equilibrium state, and
b) The level of external loading remains constant, then
the structure is said to be in stable equilibrium
• If the structure tends to remain in the disturbed state, or diverge from the deformed equilibrium state, it is said to be in neutral and unstable equilibrium respectively G. Simitses and D. Hodges (2006). Fundamentals of Structural
Stability, Elsevier
![Page 9: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/9.jpg)
Bifurcation bucklingBy bifurcation is meant the intersection of two static equilibrium paths at the same external load level
◦ That is, two solutions exist to the equilibrium equation(s) at some point
Changes in stability along the primary path occur at bifurcation points
◦ The path denoted OA denotes a stable static equilibrium path
◦ The path AB denotes unstable static equilibrium
As the load passes through its critical state, the structure passes from its unbuckled equilibrium configuration to an infinitesimally close buckled equilibrium configuration → bifurcation buckling
It is of interest to determine: ◦ Load level for which buckling takes place
◦ Stability of post-buckling solution
Pre-buckling or fundamental solution
Post-buckling or secondary solution
Bifurcation point
![Page 10: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/10.jpg)
Bifurcation buckling: Example 1 DOF
G. Simitses and D. Hodges (2006). Fundamentals of Structural Stability, Elsevier
![Page 11: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/11.jpg)
Example (small rotation)
![Page 12: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/12.jpg)
Energy method
G. Simitses and D. Hodges (2006). Fundamentals of Structural Stability, Elsevier
![Page 13: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/13.jpg)
Energy methodIt is possible to show that the following must hold true for stable equilibrium:
Note: Dn is the determinant
G. Simitses and D. Hodges (2006). Fundamentals of Structural Stability, Elsevier
![Page 14: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/14.jpg)
Energy method
G. Simitses and D. Hodges (2006). Fundamentals of Structural Stability, Elsevier
![Page 15: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/15.jpg)
Energy method: Example revisited
1. Energy stored in the system (in this case the spring)
2. Total potential energy:
3. Static equilibrium requires the total potential to have a stationary value
4. Linearized equilibrium
That is, we are concentrating our analysis to the vicinity of the fundamental solution 𝜃 = 0
![Page 16: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/16.jpg)
Energy method: Example
• Second derivative of potential energy = 0 (the criterion for bifurcation)
• Moreover, the second derivative gives an indication of the stability of equilibrium,
![Page 17: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/17.jpg)
Energy method: example
• Previously small rotations were assumed.
• Consider the total potential energy for finite rotations:
• First derivative of potential energy gives the nonlinear equilibrium equation:
![Page 18: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/18.jpg)
Energy method: Example
As before it is shown that the bifurcation load is:
The stability of the equilibrium paths can be checked
![Page 19: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/19.jpg)
Suggested exercise 11. Consider all equilibrium configurations for the presented example. Evaluate stability of each
equilibrium configuration
2.
Hints:• Use symmetry• Loading is hydrostatic, when
finding external energy, consider area (Uext = ΔA x P)
![Page 20: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/20.jpg)
Ring buckling due to hydrostatic pressureBrief overview of procedure to evaluate bifurcation buckling:
1. Establish kinematic relations
2. Constitutive relation (linear elastic)
3. Determine potential energy
4. Stationary potential energy → equilibrium
5. Perturbing and linearizing equilibrium equations, as well as substituting our fundamenal solution → bifurcation load
6. Finally, consider imperfections
![Page 21: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/21.jpg)
Ring buckling due to hydrostatic pressure
Kyriakides and Corona (2007). Mechanics of Offshore Pipelines Vol I, Buckling and Collapse, Elsevier
![Page 22: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/22.jpg)
Ring buckling due to hydrostatic pressure
![Page 23: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/23.jpg)
Ring buckling due to hydrostatic pressure
![Page 24: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/24.jpg)
Ring buckling due to hydrostatic pressure
![Page 25: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/25.jpg)
Ring buckling due to hydrostatic pressure
![Page 26: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/26.jpg)
Ring buckling due to hydrostatic pressure
![Page 27: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/27.jpg)
Ring buckling due to hydrostatic pressure
![Page 28: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/28.jpg)
Ring buckling due to hydrostatic pressure
a=0.1, 0.05, 0.01, 0
A “real” pipe will inevitably contain initial imperfections. Rather than suddenly buckle when the bifurcation load is reached, the pipe gradually deforms with increasing load.
• The figure shows increasing ovalization for three different initial ovalities as determined from eq. 4.9
• Note that the equilibrium equations were linearized, and are therefore lacking “information” – the post-buckling behavior is unknown
• Moreover, the material behavior is assumed to be purely elastic. At some point the stresses in a metallic pipe will reach yield
w
![Page 29: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/29.jpg)
Ring buckling due to hydrostatic pressure
Different post-collapse behaviors are shown for three different types of hardening.
◦ Numerical method is used to solve for the post-buckling behavior
◦ For the elastic behavior (material II), the post buckling behavior is shown to be stable → load increases after buckling
◦ Metallic materials will behave like material model (III). The post-buckling behavior of the ring then becomes unstable
“On the determination of the propagation pressure of long circular tubes”, Kyriakides, Yeh and Roach, 1984
![Page 30: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/30.jpg)
Timoshenko formula
![Page 31: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/31.jpg)
Timoshenko formula
![Page 32: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/32.jpg)
Timoshenko formula
![Page 33: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/33.jpg)
Timoshenko formula
![Page 34: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/34.jpg)
Plastic bifurcation buckling
Bifurcation buckling need not occur only in the elastic regime
◦ Plastic bifurcation may occur for initially perfectly round rings – plastic deformation occurs prior to the bifurcation
◦ Numerical treatment needed
Elastoplastic behavior leads to bifurcationpressure lower than the perfectly elastic bifurcation pressure
![Page 35: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/35.jpg)
Plastic bifurcation bucklingComparison of elastic and plastic bifurcation Note normalized by yield pressure
![Page 36: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/36.jpg)
Elastoplastic collapse of pipes
Collapse of offshore pipelines is usually a limit load instability phenomenon
◦ Initial imperfections cause a gradual ovalization of the pipe with increasing load. Ovalization accelerates as the bifurcation pressure is approached
◦ A peak load occurs due to yielding of the pipe wall – the peak load corresponds to the collapse pressure
◦ The load to maintain static equilibrium drops until touchdown
For very thin pipes bifurcation type instabilities might materialize under some load conditions (bending)
![Page 37: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/37.jpg)
Elastoplastic collapse of pipes
Comparison of bifurcation pressures (Pc) and collapse pressures (Pco) for an imperfect pipe
![Page 38: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/38.jpg)
DNV treatment of collapseThe collapse pressure is found by solving for Pc:
The external pressure at any point shall fulfill:
pmin = the minimum internal pressure that can be sustained. Normally taken as zero
Ym and Ysc are safety factors
Characteristic material strength: yield stress modified by some safety factor
Fabrication factor: depends on manufacturing
![Page 39: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/39.jpg)
Comparison of collapse expressions and experimental data
No application of safety factors
f0=1%, material with E=210,000MPa, v=0.3 and fy=450MPa, no reduction due to fabrication method and safety factor equal to unity
![Page 40: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/40.jpg)
Factors affecting collapse - Overview
• Imperfections• Ovality• Thickness eccentricity
• Material parameters• Yield stress• Hardening behavior
• Residual stresses• Anisotropic yielding• Type of loading
• Hydrostatic• Plane strain• Lateral pressure
![Page 41: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/41.jpg)
Factors affecting collapse 1. Initial ovality
As shown: 1% ovality can reduce collapse pressure by approx. 30%
![Page 42: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/42.jpg)
Factors affecting collapse
2. Wall thickness eccentricity
Of less importance if smaller than 10%. May be neglected
![Page 43: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/43.jpg)
Factors affecting collapse
3. Material yield stress
• Yield stress governs transitional value of D/t that separates elastic and plastic buckling
• Collapse pressure is roughly proportional to yield stress for plastic buckling
• Increasing the yield stress increases the collapse pressure for low D/t
0,00
20,00
40,00
60,00
80,00
100,00
120,00
12 14 16 18 20 22 24 26 28 30 32 34 36 38
Collapse pressures - X65/X80
X65 QUART Ovality = 0.25 % X80-T QUART Ovality = 0.25 %
Co
llap
se p
ress
ure
[M
Pa]
D/t
X65: SMYS = 65 ksi = 448 MPaX80: SMYS = 80 ksi = 551 MPa
SMYS: specified minimum yield stress
![Page 44: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/44.jpg)
Factors affecting collapse
3. Material stress-strain response
n: hardeing parameter in Ramberg-Osgood law
![Page 45: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/45.jpg)
Factors affecting collapse
4. Residual stresses
• Residual stresses may be introduced in the manufacturing process
• Effect increases with D/t until some point• For high D/t the effect of residual stress is
lower (see D/t=40 in graph)• High D/t buckle elastically, thus
plastic effects are less important
![Page 46: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/46.jpg)
Factors affecting collapse
5. Anisotropic yielding
• Anisotropy also introduced during manufacturing process
• Usually consider only longitudinal and circumferential direction, altough anisotropy in thickness diretion may be present
• Again, effect is less pronounced for high D/t
![Page 47: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/47.jpg)
Factors affecting collapse 6. Types of pressure loading
• Lateral pressure loading lowers collapse pressure
• Effect is apparent for low D/t• For higher D/t inelastic effects are
reduced, which reduces the difference between collapse pressures
• Hydrostatic pressure is more representative of operational conditions
![Page 48: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/48.jpg)
Pipe collapse due to pressure and bending
![Page 49: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/49.jpg)
Pipe collapse due to pressure and bending
![Page 50: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/50.jpg)
Pipe collapse due to pressure and bending
• Previous figures showed the possible scenario of collapse due to pressure and bending• In sagbend during laying (S- or J-lay) if
tension is lost (tension has stabilizing effect)• Seabed instability (rockslide) may also bend
pipe
• Bending ovalizes pipe (Brazier effect). Together with pressure leads to earlier onset of collapse
• For low D/t, the pipe will ovalize with increasing curvature until a point of dynamic collapse
• For high D/t, the pipe may experience a bifurcation instability
Mean diam.
![Page 51: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/51.jpg)
Pipe collapse due to pressure and bending
![Page 52: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/52.jpg)
Pipe collapse due to pressure and bending
• Finite element analysis of pipe collapse – the combined loading case is first pressurized then subject to bending
Progressively collapsing cross sections
Hydrostatic pressure Pure bending Bending + pressure
Onset of dynamic collapse
![Page 53: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/53.jpg)
Pipe bifurcation due to pressure and bending (thin pipes)
![Page 54: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/54.jpg)
Factors affecting collapse
1. Loading path
• Pressure → bending loading path is more critical
• Radial loading path (i.e. Increasing curvature and pressure “at the same time”) falls between P→k and k→P
![Page 55: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/55.jpg)
Factors affecting collapse
2. Residual stress
Residual stress may “reverse” ovalizationReversed collapse mode shown for low curvatures (circles with “|” in fig.). Normal collapse for higher curvature (circle with “—”)
![Page 56: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/56.jpg)
Factors affecting collapse
3a. Initial ovality orientation
• Initial ovality oriented at an angle with bending axis creates a “cusp” in the collapse envelope
• Collapse profile can become angled with respect to the bending axis
![Page 57: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/57.jpg)
Factors affecting collapse
3b. Initial ovality orientation: interplays with residual stress
Collapse at an angle with bending axis
![Page 58: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/58.jpg)
Factors affecting collapse
3c. Initial ovality orientation: effect of increased residual stress or initial ovality
![Page 59: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/59.jpg)
Factors affecting collapse
4. Wall thickness eccentricity
• For the case of no ovality imperfection a 5% thickness eccentricity oriented at 45° reduces collapse pressure by less than 1%
• Wall thickness eccentricity has the effect of “rounding” the cusp region when initial ovality is present
Orientation of thickness eccentricity
![Page 60: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/60.jpg)
Factors affecting collapse
5. Material stress-strain response
![Page 61: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/61.jpg)
Factors affecting collapse
5. Material stress-strain response
![Page 62: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/62.jpg)
Factors affecting collapse
6. Anisotropy
![Page 63: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/63.jpg)
Collapse envelopes
![Page 64: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/64.jpg)
Pressure-moment interaction
a=0.6
“Tube Collapse Under Combined Pressure, Tension and Bending Loads” Bai, Igland and Moan, ISOPE Vol. 3 No. 2, 1993
![Page 65: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/65.jpg)
Pure bending collapse formula
Collapse curvature:
Note that the stress-strain relation for this formula is characterized by:
“Tube Collapse Under Combined External Pressure, Tension and Bending” Bai, Igland and Moan, Marine Structures 10, 1997
![Page 66: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/66.jpg)
Suggested exercise 2
Consider a pipe of X-52 steel grade, with D/t=20 and initial ovality ∆0= 0.002 (i.e. 0.2%)
1. Assume that the Timoshenko formula is valid (is it?), calculate the collapse pressure
2. Calculate the pure bending collapse moment, and curvature
3. Draw the pressure-moment, and pressure-curvature interaction diagram
4. Compare your results with the interaction diagrams of the next two slides. Comment on differences
See also nomenclature at end
![Page 67: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/67.jpg)
Suggested exercise 2
![Page 68: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/68.jpg)
Suggested exercise 2
![Page 69: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/69.jpg)
NomenclatureUnless otherwise noted
![Page 70: Buckling and Collapse of Offshore Pipes under Combined](https://reader031.vdocument.in/reader031/viewer/2022012411/616b5ced4ab549358564784e/html5/thumbnails/70.jpg)
References
1. Kyriakides and Corona (2007). Mechanics of Offshore Pipelines Vol I, Buckling and Collapse, Elsevier
2. G. Simitses and D. Hodges (2006). Fundamentals of Structural Stability, Elsevier
3. T.A. Netto (2016), Collapse of Rigid Pipes under External Pressure and Bending – An Introduction
4. Bai, Igland and Moan (1993) ,“Tube Collapse Under Combined Pressure, Tension and Bending Loads” ISOPE Vol. 3 No. 2
5. Bai, Igland and Moan (1997), “Tube Collapse Under Combined External Pressure, Tension and Bending”, Marine Structures 10