CABLE TRAY RACK INSTALLATIONS

w w w. s i e m o n . c o m

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 1

Table of Contents

2

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

CTR Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Below Tray Installation Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Below Tray Installation – Perpendicular . . . . . . . . . . . . . . . . . . . . . .7

Side Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Inside Tray Installation – Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Rack Bonding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

WARNING: Failure to follow this information can result in injury or death.

CAUTION: Failure to follow this information can lead to possible equipment damage.

NOTE: Clarifying information or comment.

!

i

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 2

- Read and understand all instructions for proper installation and use of this product as improper use may lead to serious injury or death.- Before loading equipment on to the cable tray rack, be sure to torque all mounting hardware provided with the rack to a setting of 75in-lbs.- The maximum load capacity of the cable tray rack should not exceed:

CTR-02-01 - 9kg (20lbs)CTR-04-01 - 8kg (40lbs)CTR-06-01 - 27kg (60lbs)

- The cable tray racks are intended to be installed in accordance with all applicable requirements of the National Electrical Code (NEC) andthe local Authority Having

Jurisdiction (AHJ).- The minimum spacings between the accessories and components and the cable tray rackshall be maintained for safe operation of the equipment when installed in accordance with theNEC.

3

Safety Information

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 3

CTR-04-01 Diagram

4

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 4

HARDWARE

5

TOOLS REQUIRED

1/2” Socket Wrench

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 5

PARALLEL – BELOW CABLE TRAY

6

Torque all hardware to 75in-lbs

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 6

PERPENDICULAR – BELOW CABLE TRAY

7

Torque all hardware to 75in-lbs

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 7

SIDE WALL MOUNTED

8

Torque all hardware to 75in-lbs

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 8

PARALLEL – INSIDE CABLE TRAY

9

Torque all hardware to 75in-lbs

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 9

RACK BONDING

1 0

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 10

1 1

Notes

To assist safe installations, comply with the following:A. Do not attempt to perform this work with fewer than 2 technicians

B. Never touch uninsulated wire terminals unlessthe circuit has been disconnected.

C. Never install this device in a wet location.

D. Never install wiring during a lightning storm.

© 2

011

Sie

mon

Global HeadquartersWatertown, Connecticut USA

Tel: (1) 866-548-5814

For a complete listing of our global offices visit our web sitewww.siemon.com

Rev

.A

4/1

1

10

0-1

96

28

-00

INS_100.19628.00_CTR_Basket_A_A 5/3/11 10:42 AM Page 11