calgary 1 11 saska 1 11 1 - maxquip · 2020. 3. 18. · lgld2e. 150 psi (1034 kpa) 660 520 420 330...

CALGARY 1-866-629-7847 EDMONTON 1-800-661-7770 SASKATOON 1-800-667-5886 1WINNIPEG 1-844-278-5771

DELIVERY10 600 USWG TANDEM

AMMONIATRAILERS

tandem axle10,600 USWG capacity verses industry standard 8000 USWG capacity

1 866 629 7847www.maxquip.ca

Lighter weight QT steel

DELIVERY12 600 USWG TRIDEM

AMMONIATRAILERS

88" diametera manageable length that pulls better and has a lower center of gravity

Manufactured by

Manufactured by

Our trailers come loaded with lots of standard features that are not-so-standard for others!

www.maxquip.ca

PROPANE?Serving the propane distribution industry’s needs for parts, storage components andsystems, transport, pump and metering of Liquified Petroleum Gas (LPG) has been

Maxquip’s core business since our company was founded over 15 years ago!

did someone say

visit maxquip.ca to download our propane catalog

NH3PROPERTIES

Very corrosive to living tissue,copper, copper alloys and

galvanized surfaces

EXPLOSIVELIMITS16% TO 25%VOLUME OF

VAPOURIN AIR

CORROSIVENESS

AUTO IGNITIONTEMPERATURE

651°C (1,204°F)

LIQUID WEIGHT

5.14 lbs. NH3 per USGor 4.22 lbs. N per USG

AFFINITY FOR WATER

VERY HIGH

BOILING POINT

-33.3°C (-28°F)

VISCOSITY

70°F: 0.0100 cP

COLOUR

COLOURLESS

SPECIFIC GRAVITY

0.62

ODOURPUNGENT

N

H

H

H

• 1 part nitrogen (82% by weight) to 3 parts hydrogen (18% by weight).• Is a gas unless cooled to minus 28 degrees Fahrenheit (-33.3 degrees Celsius) or is sufficiently compressed.• Approximately 840 parts vapour must be compressed to equal 1 part liquid at atmospheric condi�ons. At 100 psi, liquid to vapour ra�o is approximately 1:200.• Exposure to liquid or high concentra�ons of vapour can cause severe burns.• Excessive inhala�on may cause severe damage to the lungs or suffoca�on.• Classified by the Department of Transporta�on as a non-flammable compressed gas because igni�on condi�ons are extremely difficult to achieve under normal agricultural opera�ng condi�ons.• Its strong pungent odour will discourage a person from voluntarily remaining in a concentra�on which could be injurious.• The agent for controlling ammonia emergencies and the first aid treatment for exposure are the same: WATER and lots of it quickly!• NH3 gas is lighter than air and dissolves in water.• Is typically stored & transported as a liquid under pressure.

Anhydrous Ammonia (NH3) Facts

WWW.MAXQUIP.CA • WINNIPEG 1.844.278.5771 OAKVILLE 1.800.801.8512 • MONTREAL 1.877.629.7847

5

helpful formulas

eamyTotal pounds nitrogen per hour (Lbs. N / Hour) = Implement �idth (�.) X �peed (M�H) X Rate per Acre (actual N) X 0.1212

tank capacityMaximum withdrawal rate from a NH3 nurse tank is 2% of tank capacityper minute, but will vary somewhat with temperatures of liquid andatmosphere and intake line restric�ons. �or example, a 1,000 gallon tankwill be limited to 20 gpm maximum withdrawal rate.

Plumbing Size Rates 1” Up to 3,600 Lbs. N / Hour

1 – ¼” Up to 6,000 Lbs. N / Hour 1 – ½” Over 6,000 Lbs. N/ Hour

Recommended Plumbing Nurse Tank to Meter or Cooler

Recommended Plumbing Nurse Tank to Maxflow VRC IIPlumbing Size Rates

1-1/4” Up to 3500 Lbs. N/Hour 1-1/2” Up to 6000 Lbs. N/Hour

2” 6000 Lbs. N/Hour and over

A properly designed feed line will minimi�e vapour forma�on by limi�ngline restric�ons and preven�ng vapour pocket forma�ons. �ince NH3 willhave a tendency to vapori�e, the intake piping plays a cri�cal role in theefficiency and longevity of every system. The following is a list ofconsidera�ons to ensure you have op�mal �ow rates�

• Inlet piping from tank to the metering system should be as short as possible.• Meter should be at a lower level than the tank’s lowest liquid level.• �se low restric�on type valves and ��ngs. �ong sweep radius bends are preferred.• Nearest ��ng or strainer should be at least 10 pipe diameters from the pump inlet.• Check and clean inlet strainers regularly.• Avoid up-across and down pipe loops where vapors can accumulate.

feed line plumbing considerations

traditionalmetering systemcapacities

Maximum Capacity at Various Tank Pressures (Lbs. N / Hour)

Meter 50 PSI 75 PSI 100 PSI �on�nenta� �-4103-6572 3000 3500 4000

�on�nenta� �-�500 4400 5300 6200 Raven Accuflow 1-1/4” 4000 5000 6000

Superflow 1-1/4” 6000 6500 7000

6 CALGARY 1-866-629-7847 EDMONTON 1-800-661-7770 SASKATOON 1-800-667-5886 WINNIPEG 1-844-278-5771

splitter capacity

eamy

manifold systemcapacities

Maxflow VRCMetering SystemCapacities

Maximum Pump Capacity a Various �i�eren�al Pressures (Lbs. N / Hour)

15 PSI 30 PSI 50 PSI 100 PSI MAX2A Pump 10,000 9,375 8,750 7,500 LGLD2 Pump 20,000 18,750 16,750 14,250

Maximum Capacity at Various Tank Pressures (LBS N / Hour)

50 PSI 75 PSI 100 PSI 3 �a� Spli�er

w/ Cooler 3000 3500 4000

4 �a� Spli�er w/ Cooler

4100 4800 5400


5100 6000 6800


10,560 12,540 13,860


10,560 12,540 13,860


10,560 12,540 13,860

Maximum Capacity at Various Manifold Pressures

(Lbs. N / Hour / Opener) Tradi�onal Cooler 50 PSI 75 PSI 100 PSI

*Manifold w/ ½” or 3/8” hose 105 – 145 120 – 165 140 – 190 Manifold w/ O.170 hose 77 88 100 Manifold w/ 0.125” hose 60 70 80 Manifold w/ 0.125” hose & 0.085 SS Tubes (15”)

48 55 62

Manifold w/ 0.085” hose 40 46 52 Maxflow VRC II

Manifold w/ O.170 hose 180 to 640 Manifold w/ 0.125” hose 125 to 350 Manifold w/ 0.085” hose 16 to 98 Manifold w/ 0.125” hose & 0.085 SS Tubes (15”)

30 to 180

Manifold w/ 0.125” hose & 0.055 SS Tubes (15”)

16 to 90

�ote� Manifold capaci�es are �ased on �5 �. hose len�ths� �ased on a 60” wide implement at5 MPH. *Depends on which cooler is put in front of the Manifold System



pumps, compressors & motors

2”, 3” and 4” base mounted pumps

pumps

pump & motor packages

These rugged pumps are ideal for bulk plant service, mul�ple cylinder filling applica�ons, vapourizers, bobtails andtransports. Single or double-ended drive sha� models are offered in 2, 3 and 4-inch port sizes with capaci�es rangingfrom 30 to 300 U.S. gpm (114-1,135 lpm). The LGLD2 and LGLD3 models have long been popular for bobtail servicebecause of their double-ended drive sha� arrangement, which allows the pump to be easily posi�oned for clockwise or counter-clockwise sha� rota�on. All models have an internal safety relief valve, and a replaceable casing liner andend discs for easy rebuilding of the pumping chamber if ever necessary. Standard construc�on materials includeBuna-N mechanical seals and Duravanes for handling both LP-gas and anhydrous ammonia. Maximum differen�al pressure for the 2 and 3-inch models is 150 psi (1,034 kPa), and 125 psi (862 kPa) for the 4-inch models. Ports areoffered with NPT tapped companion flanges or weld flanges.

Assembled Pump Units PumpSpeedRPM

(Using1,750RPM

Motor)

Approximate Delivery of Propane

Speeds Shown

Maximum

Pressure

MaximumWorking Pressure

Drive Rating (Maximum Horsepower Drive Will

Transmit)

Motor Size for Mounting on

Standard Base

ModelFactory

Relief ValveSetting

50 PSI(345 kPa)

100 PSI(689 kPa)

PSI kPa PSI kPa0-3

HourDuty

3-4HourDuty

8-24HourDuty

MinimumFrame

Size

MaximumFrame

SizeGPM LPM GPM LPM

BLA LGLD2E150 PSI

(1034 kPa)

660520420330

67504030

254189151114

57413023

21615511487

150 1,034 350 2,413

9.26.44.83.1

9.26.44.83.1

7.85.44.02.6

184T182T182T182T

213T184T184T182T

BLA LGLD3F150 PSI

(1034 kPa)

640520420350

1331088059

503409303223

112846042

424318227159

150 1,034 350 2,413

12.18.97.35.4

12.18.97.35.4

10.27.56.14.5

215T213T213T184T

254T215T215T184T

BLA LGLD4B150 PSI

(1034 kPa)

640520420350

270220170130

1,022833644492

22018013090

833681492341

125 862 350 2,413

26.919.615.811.4

26.919.615.811.4

22.816.613.49.8

254T254T215T213T

284T256T256T215T

Optional FlangesPump Model Standard or Optional Intake Discharge

BLA LGLD2EStandard 2” NPT 2” NPT

Optional 2” Weld 2” Weld

BLA LGLD3FStandard 3” NPT 3” NPT


BLA LGLD4B

Standard 4” Weld 3” Weld

Optional 3” NPT 3” NPT


Optional 4” Weld 4” WeldLGLD4 Cutaway

All assembled pumps packages come mounted on a C-channel base with drive guard. All belts and sheaves areinstalled. Please specify pump inlet and outlet flanges as well as motor voltages required. Gear reduced models alsoavailable. Motor sizes and voltages may be ordered to fit your exact requirements - we carry pump and motorpackages for 2” to 4” size pumps. Please contact your local Maxquip branch for more informa�on.

HR Drive Style Helical Gear

Reduction DriveV-Belt Drive



3” and 4” truck mount pumps

pumps

Blackmer TLGLF3 and TLGLF4 pumps are designed to flange mount directly to a commercial internal control valve, in combina�on with the tank of a bobtail or transport. Direct moun�ng eliminates the need for inlet pipes, shut-off valve and external strainer which can restrict flow and cause vapouriza�on problems. The result is smootheropera�on and longer pump life. Both models are equipped with a double-ended drive sha� for clockwise or counter-clockwise rota�on by simply changing posi�on of the pump. Each model also has an auxiliary intake port which canbe used for emergency unloading of another tank or transport. In addi�on, these pumps have an internal safetyrelief valve, and a replaceable casing liner and end discs for easy rebuilding of the pumping chamber if ever necessary.Standard construc�on materials for both models include Buna-N mechanical seals and Duravanes for handling both LP-gas and anhydrous ammonia. The TLGLF3 is widely used on bobtails because of its compact moun�ng arrange-ment, with a 3-inch ANSI intake flange and 2-inch auxiliary intake and discharge ports. Capaci�es range from 60 to110 U.S. gpm (227 to 416 lpm). The TLGLF4 offers maximum output rates, and fast turnaround �me for transports. It is designed with 4-inch ANSI intake flange, a 3-inch auxiliary intake port, and twin 2-inch discharge ports whichpermit the use of two hoses, if necessary, to reduce pressure loss when unloading into restric�ve receiving systems.

Standard Pump

PumpSpeedRPM

Maximum

Pressure

MaximumWorkingPressure

Model

FactoryRelief Valve

Setting

50 PSI (345 kPa) 100 PSI (689 kPa)

GPM LPM BHP KWTorque

GPM LPM BHP KWTorque

PSI kPa PSI kPaFt./lbs Kg/m Ft./lbs Kg/m

BLA TLGLF3C150 PSI

(1,034 kPa)

870 129 488 6.5 4.8 45.9 6.3 119 450 10.9 8.1 72.5 10

125 8.62 350 24.13

800 118 449 5.1 3.8 44.2 6.1 107 405 8.7 6.5 69.7 9.6

650 93 352 5.0 3.7 40.4 5.6 81 307 7.9 5.9 63.8 8.8

600 85 322 4.5 3.4 39.4 5.4 73 276 7.0 5.2 61.3 8.5

500 70 265 3.6 2.7 37.8 5.2 59 223 5.7 4.3 59.9 8.3

400 52 197 2.8 2.1 36.8 5.1 40 151 4.5 3.4 59.1 8.2

BLA TLGLF4B 150 PSI(1,034 kPa)

800 350 1,325 22 16 143 20 309 1,158 34 25 223 31

125 8.62 350 24.13

650 280 1,060 15.5 11.6 125.2 17.3 245 927 25.0 18.6 201.9 27.9

600 260 984 14.3 10.7 125.1 17.3 220 833 23.0 17.2 201.3 27.8

500 210 795 11.9 8.9 125.0 17.3 170 644 19.0 14.2 199.5 27.6

400 160 606 9.5 7.1 124.7 17.2 120 454 15.2 11.3 199.5 27.6

StandardPump

Standard orOptional Discharge Auxiliary Intake Intake

BLA TLGLF3C

Standard 2” NPT Elbow 2” NPT3”

300#ANSI

Flange

Optional 2” NPT Elbow 2” NPT

Optional 2” Weld Elbow 2” Weld

Optional 2” Weld Elbow 2” Weld Elbow

BLA TLGLF4

Standard Twin 2” NPT Blank Flange

4”300#ANSI

Flange

Optional Twin 2” NPT 3” NPT

Optional Twin 2” Weld 3” Weld

Optional Twin 2” Weld Blank Flange

Optional Twin 2” NPT 4” Weld

Discharge and Auxiliary Intake Flange OptionsTLGLF3 TLGLF4

0 2 4BAR

DIFFERENTIALPRESSUREPSI

6 8

0

4

2

6

8

10

12

0 20 40 60 80 100 120

400

500

600650800

870

BRAK

EHP

REQU

IRED

RPM87080065060050040000

200100

300400500

4080120160

LITERS

/MIN.

U.S.GA

L/M

IN.

0 2 4BAR

DIFFERENTIALPRESSURE PSI

6 8

0 20 40 60 80 100 120

350

520

420

640

800

0

4

8

12

16

20

24

28

32

36

40

BRAK

EHP

REQU

IRED

RPM

800640520420350

00

400

800

1200

100200300400

LITERS

/MIN.

U.S.GA

L/M

IN.

PerformanceCurvesTLGLF3 TLGLF4

Selection DataPump delivery and brake ho rsepower requi rements are listed in the table below for var ious di�er entialpressur es. The same data for all pressures is provided in the performance curves below.

Available CompanionFlangesandFlangedElbows

NOTE: Blackmer Characteristic Curves are based on Brake Horsepower (BHp). To determine Motor Horsepower, drive trainine�iciencies must be addedto the BHp.These curves are based on approximate delivery rates whenhandlingpropane or anhydrous ammoniaat 80ºF(26.7ºC).Linerestrictions such as excess �ow valves, elbows, etc., will adversely e�ect deliveries. For propane at 32ºF(0ºC), actualdelivery will be further reduced to about 80% of nominal. Delivery of butane at 80ºF(26.7ºC)will be 60 to 70%of these values,

1 Check thepump’sdelivery andbrake horsepowerrequirementsin theperformancecurves below. See footnotewith thecurves which explains the factors thatcan cause delivery to vary.2 Maximumratedworkingpressure is 350psi (24.13Bar) for LPG andNH3 (limitedbyU.L. andN.F.P.A. 58).Note: Refer toback cover for external bypass valve information.

StandardPump

PumpSpeedRPM

ApproximateDelivery of Propaneat Di�erential PressuresandPumpSpeeds Shown1

MaximumDi�erentialPressure

MaximumWorkingPressure2

ModelFactoryReliefValveSetting

50PSI (3.45bar) 100PSI (6.89Bar)

PSI Bar PSI BarGPM LPM BHP KW

TorqueGPM LPM BHP KW

Torque

ft-lb Kg-m ft-lb Kg-m

TLGLF3 150PSI(10.34Bar)

870 129 488 6.5 4.8 45.9 6.3 119 450 10.9 8.1 72.5 10 125 8.62 350 24.13800 118 446 5.1 3.8 44.2 6.1 107 405 8.7 6.5 69.7 9.6 125 8.62 350 24.13650 93 352 4.3 3.2 40.4 5.6 83 314 7.9 5.9 63.7 8.8 125 8.62 350 24.13600 85 322 4 3 39.3 5.4 75 284 7.1 5.3 62.2 8.6 125 8.62 350 24.13500 70 265 3.6 2.7 37.4 5.2 68 257 6 4.5 61.5 8.5 125 8.62 350 24.13400 52 197 2.8 2.1 36.2 5 40 151 4.8 3.6 60.8 8.4 125 8.62 350 24.13

TLGLF4 150PSI(10.34Bar)

800 350 1,325 22 16 143 20 306 1,158 34 25 223 31 125 8.62 350 24.13650 280 1,060 15.5 11.6 125.2 17.3 245 927 25.0 18.6 201.9 27.9 125 8.62 350 24.13600 260 984 14.3 10.7 125.1 17.3 220 833 23.0 17.2 201.3 27.8 125 8.62 350 24.13500 210 795 11.9 8.9 125.0 17.3 170 644 19.0 14.2 199.5 27.6 125 8.62 350 24.13400 160 606 9.5 7.1 124.7 17.2 120 454 15.2 11.3 199.5 27.6 125 8.62 350 24.13

Pump Discharge Auxiliary Intake Intake

TLGLF3

2"NPT FlangedElbow

2"Weld FlangedElbow

2” NPTFlanged

2” WeldFlanged

2"NPT Flanged

3"300lb.ANSI

MountingFlange

2"NPT FlangedElbow

2"Weld Flanged

2"Weld FlangedElbow

BlankingFlange

TLGLF4

Twin 2"NPTFlanges

Twin 2"WeldFlanges

3"NPT Flanged

4"300lb.ANSI

MountingFlange

3"Weld Flanged

BlankingFlange

4"Weld Flanged

TLGLF3 Cutaway TLGLF4 Cutaway

Capaci�es range from 200 to 300 U.S. gpm (757 - 1,135 lpm). Maximum differen�al pressure for both models is 125 psi (862 kPa).



Ref. No. Part Number Descrip�on Qty

4 BLA 414401 Cover – Relief Valve (R/V) 1

5 BLA 920331 Capscrews – R/V Cover 6

8 BLA 471423 Spring - R/V 1

9 BLA 454405 Valve – R/V 1

10 BLA 701919 O-Ring – R/V Cover 1

12 BLA 014405 Casing 1

13 BLA 264445 Rotor & Sha� Asy. 1

14 BLA 091419 Vane – Duravane (Std.) 6

20 BLA 034416 Head 2

21 BLA 920351 Capscrews – Head 32

24 BLA 903156 Ball Bearing 2

24A BLA 903521 Locknut – Bearing 2

24B BLA 903522 Lockwasher – Bearing Cover 2

26 BLA 383940 Gasket – Bearing Cover 2

27 BLA 041431 Bearing Cover 2

28 BLA 920285 Capscrews – Bearing Cover 8


35 BLA 909209 Key – Sha� 1

41 BLA 184403 Liner 1

42 BLA 654401 Flange – NPT 2

42A BLA 702004 O-Ring – Flange 2

42B BLA 920384 Capscrew – NPT Flange 8

71 BLA 064412 Disc 2

72 BLA 702022 O-Ring – Head 2

73 BLA 908198 Gage Plug 2

74 BLA 183991 Key – Liner 1

76 BLA 317815 Grease Fi�ng 2

76A BLA 701992 Grease Relief Fi�ng 2

77 BLA 123904 Push Rod 3

104 BLA 331918 Grease Seal 2

123A BLA 701480 Dirt Shield 2

153 Next Page Mechanical Seal Assembly 2

1866 BLA 341601 Sha� Protector 1

- BLA 903091 Tool – Locknut -

parts list for pump model: max2a

pumps



parts list for pump model: lgld3f, lgl3f

pumps


4 BLA 415113 Cover – Relief Valve (R/V) 1

5 BLA 920331 Capscrews – R/V Cover 6

8 BLA 475135 Spring – R/V1 1

9 BLA 455129 Valve – R/V 1

10 BLA 701925 O-Ring – R/V Cover1 1


13 BLA 265149 Rotor & Sha� Asy. LGL 1

13A BLA 265148 Rotor & Sha� Asy. LGLD5,2 1

14 BLA 095131 Vane – Duravane1 6

20 BLA 035128 Head 2

21 BLA 920369 Capscrew – Head 40

24 BLA 903172 Ball Bearing1 2

24A BLA 903523 Locknut – Bearing2 2

24B BLA 903524 Lockwasher – Bearing1 2

26 BLA 385125 Gasket – Bearing Cover1 2

27 BLA 041815 Bearing Cover 2

28 BLA 920285 Capscrew – Bearing Cover 12


35 BLA 909130 Key – Sha�1,7 1

41 BLA 185111 Liner2 1

42 BLA 655112 Flange – NPT 2

42A BLA 702002 O-Ring Flange1 2


71 BLA 065112 Disc1 2

72 BLA 702041 O-Ring – Head1 2


74 BLA 185191 Key – Liner2 1



77 BLA 125105 Push Rod1 3

104 BLA 331908 Grease Seal1,3 1



- BLA 898981 Kit – Maintenance -

- BLA 899081 Kit – Rebuild - 1Included in Maintenance Kit and Rebuild Kit 2Included in Rebuild KitThe following applies to double end sha� pumps (LGLD): 3 Use Two 5Double-Ended Rotor & Sha� 7 Pumps before April 2008 used Woodruff key 909130, included in Maintenance kits.



parts list for pump model: lgld4b

pumps

1Included in Maintenance Kit and Rebuild Kit 2Included in Rebuild Kit


1 BLA 413957 Cap – Relief Valve (R/V) 1

2 BLA 436310 Adjus�ng Screw – R/V 1

3 BLA 432039 Locknut – Adjus�ng Screw 1

4 BLA 412001 Cover – R/V 1

5 BLA 920663 Capscrew – R/V 4

7 BLA 426355 Spring Guide – R/V 1

8 BLA 472039 Spring – R/V 1 1

9 BLA 452001 Valve - R/V 1

10 BLA 701946 O-Ring – R/V Cover 1 1


13 BLA 262041 Rotor & Sha� Asy, Dbl End 2 1

14 BLA 092019 Vane – Duravane 1 6

20 BLA 032041 Head 2


24 BLA 903166 Ball Bearing 1 2

24A BLA 903541 Locknut – Bearing 2 2

24B BLA 903542 Lockwasher – Bearing 1 2

26 BLA 385125 Gasket – Bearing Cover 1 2

27 BLA 041815 Bearing Cover - LGLD4B 2


35 BLA 909183 Key – Sha� 1 1

41 BLA 182000 Liner 2 1


42 BLA 652012 Flange – 3” NPT

1-2

BLA 652007 Flange – 3” Weld


42A BLA 701937 O-Ring – NPT, Weld Flange 1 2


- BLA 920640 Capscrew – Weld Flange -

71 BLA 062039 Disc 1 2

71A BLA 920015 Machine Screw – Disc 2 8

71B BLA 909634 Lockwasher – Machine Screw2 8

72 BLA 702039 O-Ring – Head 1 2


74 BLA 182040 Key – Liner 2 1



77 BLA 122009 Push Rod – composite 1 3

88 BLA 701926 O-Ring – R/V Cap 1 1

104 BLA 331908 Grease Seal 1 2




- BLA 899022 Kit – Rebuild -


parts list for pump model: tlgf4b

pumps



parts list for pump model: tlgf4b

1Included in Maintenance Kit and Rebuild Kit 2Included in Rebuild Kit


1 BLA 413957 Cap – Relief Valve (R/V) 1

2 BLA 436310 Adjus�ng Screw – R/V 1

3 BLA 432039 Locknut – Adjus�ng Screw 1

4 BLA 412001 Cover – R/V 1

5 BLA 920663 Capscrew – R/V 4

7 BLA 426355 Spring Guide – R/V 1

8 BLA 472039 Spring – R/V 1 1

9 BLA 452001 Valve - R/V 1

10 BLA 701946 O-Ring – R/V Cover 1 1


13 BLA 262041 Rotor & Sha� Asy, Dbl End 2 1

14 BLA 092019 Vane – Duravane 1 6

20 BLA 032041 Head 2


24 BLA 903166 Ball Bearing 1 2

24A BLA 903541 Locknut – Bearing 1 2

24B BLA 903542 Lockwasher – Bearing 2 2

26 BLA 385125 Gasket – Bearing Cover 1 2

27 BLA 041815 Bearing Cover - LGLD4B 2


35 BLA 909183 Key – Sha� 1 1

41 BLA 182000 Liner 2 1

42 BLA 652012 Flange – 3” NPT

1 BLA 652007 Flange – 3” Weld



42 BLA 652000 Flange - Blank 1

42A BLA 701937 O-Ring – NPT, Weld Flange 1


BLA 920640 Capscrew – Weld Flange

TWIN DISCHARGE PORT OPTIONS

43 BLA 652010 Flange – 2” NPT 2 BLA 652024 Flange – 2” Slip-on Weld

43A BLA 702004 O-ring – 2” Discharge Flanges1 2

43B BLA 920491 Capscrew – Discharge Flange 8

71 BLA 062039 Disc 1 2

71A BLA 920015 Machine Screw – Disc 2 8

71B BLA 909634 Lockwasher – Machine Screw2 8

72 BLA 702039 O-Ring – Head 1 2


74 BLA 182040 Key – Liner 2 1



77 BLA 122009 Push Rod – composite 1 3

88 BLA 701926 O-Ring – R/V Cap 1 1

104 BLA 331908 Grease Seal 1 2

153 BLA 332050 Mechanical Seal Assembly 2




- BLA 899022 Kit – Rebuild -



pumps, compressors & motorsbypass valves

Blackmer differen�al bypass valves are designed to protect pumps and system components from excessive pressure damage. Blackmer offers five different models that provide full-flow pressure control to 250 U.S. gpm (946 lpm) at120 psid (827 kPa). Installa�on is easy with NPT tapped ports in sizes from 3⁄4” to 2”. All models are suitable for bothLP gas and anhydrous ammonia service.

In opera�on, Blackmer valves provide excep�onally close pressure control, even under widely varying bypass flow condi�ons. Blackmer bypass valves have no small, easily plugged, sensing passages; and with only two moving parts,their opera�on is simple and reliable. They open precisely at the preset spring pressure, and they close smoothly and quietly, thanks to a patented dash-pot design. A small chamber in the valve stem fills with liquid when the valveopens. This liquid then provides a hydraulic cushion preven�ng the valve from slamming shut if pressure is suddenly released. It also minimizes cha�er and valve seat wear when pressures hover around the crucial limit.

Model Number Description

Model BV3/4 Model BV1 Either valve can be used with 1-1/4 or 1-1/2 Blackmer Pumps

Model BV1-1/4Model BV1-1/2

These models are normally used for bobtail trucks and smaller bulk plant systems.Either valve can be used with 2 or 3” Blackmer pumps.

Model BV2 The BV2 model is widely used for transports or larger bulk plant systems.

Model

Maximum Rated Flow - GPM (LPM)

20 PSI(138 kPa)

50 PSI(345 kPa)

80 PSI(552 kPa)

120 PSI(827 kPa)

BLA BV1 25 (95) 40 (151) 50 (189) 50 (227)

BLA BV1-1/2 60 (227) 80 (303) 100 (379) 125 (473)

BLA BV2 150 (568) 180 (681) 220 (833) 250 (946)

Selection Guide



LB081 compact oil-free gas compressors for liquid transfer & vapour recovery

compressors

Distributed By:

502-002 © 2014 Blackmer

Process | Energy | Military & Marine

World Headquarters1809 Century Avenue SW, Grand Rapids, MI 49503-1530 USA

T +1 616.241.1611 F 616.241.3752 www.blackmer.com

Sales Information and Equipment Application AssistanceBlackmer has a world wide distribution network to assist you in specifying any of our family of pumps, compressors and other equipment for your application. For more information or to find the distributor nearest you, please contact us or visit our web site.

Standard Compressor PackagesBlackmer offers a variety of factory assembled compressor packages to fit most application requirements.

CO – COMPRESSOR ONLY Includes basic compressor with flywheel.

B – BASE MOUNTED UNIT Includes compressor, pressure gauges, formed steel base, V-belt drive with belt guard, and adjustable motor base, less motor.

TU – TRANSFER UNIT Includes compressor, pressure gauges, formed steel base, liquid trap assembly with a mechanical float, V-belt drive with belt guard, and adjustable motor base, less motor.

TC or TW – TRANSFER UNIT Includes compressor, pressure gauges, steel base, ASME code stamped liquid trap assembly (complete with relief valve and a NEMA 7 electric float switch for Propane service), V-belt drive with belt guard, and adjustable motor slide base. TW units feature welded and flanged piping.

LU – LIQUID TRANSFER/VAPOR RECOVERY UNIT Includes compressor, pressure gauges, formed steel base, liquid trap assembly with a mechanical float, inlet strainer, interconnecting piping, 4-way valve, V-belt drive with belt guard, and adjustable motor base, less motor.

LC or LW – LIQUID TRANSFER/VAPOR RECOVERY UNIT Includes compressor, pressure gauges, steel base, ASME code stamped liquid trap assembly (complete with relief valve and a NEMA 7 electric float switch for Propane service), inlet strainer, interconnecting piping, 4-way valve, V-belt drive with belt guard, and adjustable motor base, less motor. LW units feature welded and flanged piping.

LB081 Oil-Free Reciprocating Gas Compressor

Compressor Selection Data: Propane and Anhydrous Ammonia

1 Delivery will depend on proper system design, pipe sizing and valve capacity.2 Horsepower is for liquid transfer and vapor recovery in moderate climates. For liquid transfer without vapor recovery, horsepower will be lower. For severe climates, contact your Blackmer representative for horsepower required.3 Use next larger pipe size if piping exceeds 100 feet (30 meters).

ModelSpeed Approximate Liquid

Transfer Delivery1 Piston Displacement Driver Size2Pipe Diameter3

Vapor Liquid

rpm U.S. gpm L/min CFM M3/H hp kW in. mm in. mm

LB081425 25 93 4.2 7.2 1.5 1.1 0.75 19 1.5 38

560 32 123 5.6 9.5 3 2 0.75 19 1.5 38

715 41 157 7.2 12.2 3 2 1 25 1.5 38

780 45 171 7.8 13.3 5 4 1 25 1.5 38

810 46 174 8.1 13.8 5 4 1 25 1.5 38

Blackmer oil-free gas compressors deliver high efficiency in handling propane, butane, anhydrous ammonia andother liquefied gases. At about half the capacity of the Blackmer LB161, the LB081 is well suited to small plants orvessels. Equipped with high efficiency valves, steel pistons, self-adjus�ng piston rod seals and other robust features, these compressors are designed to provide maximum performance and reliability under the most severe service condi�ons and offer the best combined characteris�cs of sustained high level performance, energy efficiency, trouble-free opera�on and low maintenance cost.

High efficiency valves that move more gas volume, the heart of any compressor is its valve assembly and Blackmervalves are specifically designed for non-lubricated gas applica�ons. With precisely engineered clearances, springtension, and a special finish, these valves seat more posi�vely so more gas is moved with each piston stroke.

Blackmer valves offer greater strength, quiet opera�on, and long life.

Compressor Selection Data: Propane and Anhydrous Ammonia

Applica�ons well suited for the LB081 include:• Small tank unloading• Portable evacua�on skids• Line stripping• Vapour recovery



weg motors

W21X is an explosion-proof motor especially designed to operate in environments with the presence of explosiveatmospheres. It has robust construc�on, a flame reten�on system with gaps between the parts carefully designed, accurate machining on the terminal box and screws with high mechanical strength. It meets the requirements of explosive atmospheres like Zone 1 and Zone 2.

motors

ALTITUDE 1000 m.a.s.l.

COOLING TEFC – Totally Enclosed Fan Cooled (IC411)

ENCLOSURE MATERIAL Cast Iron

FREQUENCY 60 HZ

INSULATION CLASSF with Class B (80K) rise on DOLF with Class F (105K) rise on VFD

AMBIENT TEMPERATURE -20 to 40°C

PHASES Three-Phase

PROTECTION DEGREE IP55

SERVICE FACTOR1.15 on DOL1.00 on VFD

SERVICE PERIOD S1 - Continuous

STANDARD NEMA

STARTING METHOD DOL / Inverter Duty

BEARINGS Anti-Friction Ball Bearings

CONNECTION Direct coupled

AREA CLASSIFICATIONCSA / UL: Class I, Div 1, Groups C & DCSA: Class II, Div 1, Groups F & GCSA: Class I, Zone 1, IIB

APPROVAL CSA

Standard Features:Sealing:• Nitrile rubber oil seal: up to frame 213/5T• Viton oil seal: from frame 254T up to 586/7T• Spike Resistant WISE wire• 230/460V - Protects against IGBT voltage spikes up to 2000V• 575V - Protects against IGBT voltage spikes up to 2400V• Exceeds NEMA MG1 Part 31.4.4.2Insula�on System:• Dip and Bake Insula�on system with class “H” resin up to frame 324/6T• CFRI Con�nuous Flow Resin Impregna�on Insula�on system with

class “H” resin for frame 364/5T and upPaint Plan (C3 rated):• 202P – Color: RAL 5009 - Blue

Part Number Description

WEG HX010504NPW21X 10 HP 1800 575 XP - L215T NP W21X

WEG HX010404NPW21X 10 HP 1800 2X4 XP - 213/5T NP W21X

WEG HX015504NPW21X 15 HP 1800 575 XP - 254T NP W21X

WEG HX015404NPW21X 15 HP 1800 2X4 XP - 254T NP W21X







WEG SB215DAB Slide Base 215T - Double Adjusting




WEG SB286DAB Slide Base 286T -Double Adjusting

• Re-greasable bearings for frames 254/6T and up• Winding thermostats – 1 per phase NC - wired into the main t-box


63

Prices All quotations are made for immediate acceptance unless otherwise stated. Prices are subject to change without notice. Prices are quoted FOB our ware-house exclusive of applicable taxes unless otherwise stated. We shall not be held responsible for any consular fees, fees for legalizing invoices, certificates of origin, stamping bills of lading, or other charges required by the laws of any country of destination, or any fines, penalties or interest imposed due to incorrect declarations.

PaymentWe accept cash, cheques, electronic fund transfers, MasterCard or Visa. Payment is due upon receipt of invoice. Late charge of 2% per month, which is an annual percentage of 24% may be assessed on all overdue accounts. Payment is due whether or not technical documentation and/or any third party certifi-cations are complete at the time of shipment. We will be entitled to recover all reasonable attorneys’ fees and other costs incurred in the collection of overdue accounts.

Credit LimitWith credit approval, you will be allowed to charge to an open account. We accept cash, cheque or electronic fund transfer only for payment of account. Your credit limit will be set according to the references listed on your credit application if you have not established credit. Your creditworthiness may be re-con-firmed from time to time at our sole discretion. We reserve the right, where a genuine doubt exists as to your financial position or if you are in default of any payment obligation, to suspend delivery or performance of any agreement or any part thereof without liability and without prejudice to, and without limita-tion of, any other remedy available to us until you cure the default or satisfactory security for payment has been provided. We will have the option to extend the delivery date by a time at least equal to the period of such suspension.

Damage/Shortage ClaimsAll goods are carefully packed and inspected prior to shipping. We will attempt to pack or prepare all shipments so that they will not break, rust or deterio-rate in shipment, but we do not guarantee against such damage. Check all goods immediately upon receipt. If goods are damaged in transit or shortages appear, it is your responsibility to file a claim with the delivery carrier. We accept no responsibility for any damage, shortage or loss in transit. Ownership and risk of loss passes to you upon the earlier of (a) our delivery of the goods, or (b) invoicing by us for the goods where you are unable to accept delivery on the scheduled date. We will retain a security interest in the goods until the purchase price has been paid, and you agree to perform upon request all acts required to secure our interest. Please note all damages and shortages on the freight bill before signing. All shortages must be reported within 24 hours after receipt of shipment or claim will be denied.

ShipmentsFees for carriers will be prepaid and invoiced to the customer, unless otherwise directed by the customer to use the customer’s own account with a specific carrier. Shipments made by bus lines and common courier will be collect unless otherwise specified. We do not ship via postal service. Unless otherwise agreed to by us in writing, delivery terms shall be EXW Maxquip’s premises (INCOTERMS 2010), except to the extent modified by this General Terms and Conditions. Where goods are to be supplied from stock, such supply is subject to availability of stocks at the date of delivery. Partial shipments may be made as agreed to between you and us. Stated delivery dates are approximate only and cannot be guaranteed. We will have no liability for damages arising out of the failure to keep a projected delivery date, irrespective of the length of the delay. In the event you are unable to accept delivery of goods when tendered, we may, at our option, arrange for storage of the goods at your sole risk and you will be liable to us for the reasonable cost of such storage. This provision is without prejudice to any other rights which we may have with respect to your failure to take delivery of goods, which includes the right to invoice you for the goods. You agree that title to the stored goods will transfer to you upon invoicing notwithstanding your inability to accept delivery and that you assume all risk of loss or damage to the goods from the date title passes to you. You are responsible for all shipping costs from our premises to the location as designat-ed by you. All shipping costs for the return of goods from the location specified by you to our premises will also be for your account.

Special OrdersOn special items we order that are not normal stock items, we cannot accept cancellations or returns in most cases. In certain cases (to be determined by Maxquip Inc. in its sole discretion) returns may be possible, subject to a restocking fee.

ReturnsNo returns will be accepted after 30 days. No material should be returned for credit without Maxquip’s approval. All freight charges must be prepaid on returned items, and all original prepaid freight charges must be paid in full. Goods returned must be accompanied by a Returned Goods Authorization (RGA) number and a copy of the original invoice. All shipped to Maxquip without prior authorization (RGA) will not be accepted and the item will be returned freight collect. Restocking charges will apply.

General Terms & Conditions

SURREY 1.855.258.3835 • CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 • SASKATOON 1.800.667.5886

64

continued...

WarrantyWarranties as expressed by individual manufacturers will be honored. We will comply with all instructions given by the manufacturer in each given instance. All freight charges incurred on warrantable items are the customers responsibility. Please return warrantable/defective items to Maxquip Inc. within 30 days or the warranty will be void.

TaxesYou will be responsible for, and shall protect, indemnify, defend and save harmless, us from and against the reporting, filing and payment of any taxes, duties, charges, licenses, or fees (and any related fines, penalties or interest and the like) imposed directly on you in connection with the purchase of the goods and all liabilities, costs, and associated expenses (including lawyers’ and experts’ fees) which may be incurred in connection therewith. Such taxes, duties, charges, licenses, or fees include but are not limited to any local, state, federal, foreign, or international sales, use, value added tax (“VAT”), goods and services tax (“GST”), rental, import, export, personal property, stamp, excise and like taxes and duties. If we pay any such tax, you will, within thirty (30) days of our demand, reim-burse us for the tax including interest, fines, and penalties, paid by us. It will be your sole obligation after payment to us to challenge the applicability of any tax. Notwithstanding the foregoing, we will provide you with a copy of all exporting documents and any other documents reasonably requested by you to prove or substantiate to the appropriate tax authorities the goods were timely exported.

CooperationYou will cooperate with us, and at our request, you will use your best efforts to supply us such information (including documentary information) in connection with your activities as may be required by us for any of the following purposes:

a) to enable us to comply with the lawful demand or requirement for such information by any appropriate government authority or to en sure that all requirements of the applicable law are being complied with; b) to enable us to conduct, defend, negotiate or settle any claim arising out of, or in connection with, such activities, whether or not such claim shall have become the subject of arbitration or judicial proceedings; c) to enable us to make any application (including, but without limitation, any claim for any allowances or relief ) or representation in connection with, or to contest any assessment on, or our liability in connection with any taxes, duties, levies, charges and contributions (and any interest or penalties thereon); or d) to secure for us any beneficial tax treatment and legally minimize any tax obligations in connection with the sale of our goods.

Liabilities, Releases and IndemnificationFor purpose of this section, the following definitions will apply:

“Claims” shall mean all claims, demands, causes of action, liabilities, damages, judgments, fines, penalties, awards, losses, costs, expenses (including, without limitation, attorneys’ fees and costs of litigation) of any kind or character arising out of, or related to, the performance of or subject matter of this Agreement (including, without limitation, property loss or damage, personal or bodily injury, sickness, disease or death, loss of services and/or wages, or loss of consortium or society).

NOTWITHSTANDING ANYTHING CONTAINED IN THIS AGREEMENT TO THE CONTRARY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER AND EACH PARTY RELEAS-ES THE OTHER FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOST PRODUCTION, LOST REVENUE, LOST PRODUCT, LOST PROFIT, LOST BUSINESS OR BUSINESS OPPORTUNITIES.

Maxquip’s total liability for all claims, damages, causes of action, demands, indemnities, judgments, fines, penalties, awards, losses, costs and expenses(including attorney’s fees and cost of litigation) shall be limited to and shall not exceed the value of the goods purchased by the customer.

Maxquip shall not be liable for any claims, damages, causes of action, demands, indemnities, judgments, fines, penalties, awards, losses, costs and expenses (including attorney’s fees and cost of litigation) that may arise as a result of the customer’s use of the supplied equipment in a manner which such equipment is not adequately certified for. The customer is required to ensure appropriate certification for the equipment it intends to use and to confirm that such certifica-tion(s) are applicable for the jurisdiction in which the equipment is being used and have not expired, changed or otherwise materially been altered.

The customer acknowledges that the customer has selected the equipment and that Maxquip does not and will not make any representation or warranty, express or implied, with respect to the equipment or its adequacy for the customer’s purpose or otherwise. Except as expressly stated herein, Maxquip makes no other representation, warranty or condition with respect to the equipment and disclaims all other representations, warranties or conditions, express or implied, with respect to the merchantability or fitness for a particular purpose of the equipment.

THE EXCLUSIONS OF LIABILITY, RELEASES AND INDEMNITIES SET FORTH IN THIS SECTION SHALL APPLY TO ANY CLAIM(S), LOSSES OR DAMAGES WITHOUT REGARD TO THE CAUSE(S) THEREOF, INCLUDING BUT NOT LIMITED TO PRE-EXISTING CONDITIONS, WHETHER SUCH CONDITIONS BE PATENT OR LATENT, THE UN-SEAWORTHINESS OF ANY VESSEL OR VESSELS, IMPERFECTION OF MATERIAL, DEFECT OR FAILURE OF PRODUCTS OR EQUIPMENT, BREACH OF REPRESENTATION OR WARRANTY (EXPRESS OR IMPLIED), ULTRAHAZARDOUS ACTIVITY, STRICT LIABILITY, TORT, BREACH OF CONTRACT, BREACH OF DUTY (STATUTORY OR OTHER-WISE), BREACH OF ANY SAFETY REQUIREMENT OR REGULATION, OR THE NEGLIGENCE OR OTHER LEGAL FAULT OR RESPONSIBILITY OF ANY PERSON (INCLUDING THE INDEMNIFIED OR RELEASED PARTY), WHETHER SUCH NEGLIGENCE BE SOLE, JOINT OR CONCURRENT, ACTIVE OR PASSIVE.

Force MajeureIf either party is unable by reason of Force Majeure (as defined below) to carry out any of its obligations under this Agreement, other than the obligations to pay money when due and indemnification obligations assumed hereunder, then on such party giving notice and particulars in writing to the other party within a reasonable time after the occurrence of the cause relied upon, such obligations shall be suspended. “Force Majeure” shall include acts of God, laws andregulations, government action, war, civil disturbances, strikes and labor problems, delays of vendors, carriers, lightening, fire, flood, washout, storm, breakage or accident to equipment or machinery, shortage of raw materials, and any other causes that are not reasonably within the control of the party so affected. We will be paid our applicable standby rate, if any, during any such Force Majeure event.

SURREY 1.855.258.3835 • CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 • SASKATOON 1.800.667.5886

66

TX & TXD seriessliding vane pumps

STX DEF series

TRANSPORT PUMPSFOR DIESEL EXHAUST

FLUID (DEF)

www.maxquip.ca

PUMPSPETROLEUM

WE ALSO OFFER:hand operated pumps

transport pumps for defsliding vane pumps

heavy duty sliding vane pumps

GNX & GNXH series

alignment free - heavy duty sliding vane pumps


67

TX & TXD seriessliding vane pumps

STX DEF series

TRANSPORT PUMPSFOR DIESEL EXHAUST

FLUID (DEF)

www.maxquip.ca

PUMPSPETROLEUM

WE ALSO OFFER:hand operated pumps

transport pumps for defsliding vane pumps

heavy duty sliding vane pumps

GNX & GNXH series

alignment free - heavy dutysliding vane pumps

calgary 1 11 saska 1 11 1 - maxquip · 2020. 3. 18. · lgld2e. 150 psi (1034 kpa) 660 520 420 330...

Documents