Te

ch

no

log

y

129

ALLIGATOR CLIPS

28ALCL $2.50 $2.75 28BASO $0.55 $0.61

BANANA PLUGS

CROCODILE LEADS

28LEDSET $2.80 $3.08

2 X FLASHING LEDS WITH HOLDER & SWITCH

The sharp pointed teeth on these clips will ensure a good connection for leads. Jaw capacity 10mm. Pack of 5.

packet of 50.

410mm long with crocodile clips at either end. 10 per pack. Assorted colours.

Includes AA battery holder, switch, resistor, wire and 2 flashing LEDs. Fantastic for making toys with flashing eyes. Multi coloured only. Price per each.

28LECR $5.90 $6.49

ELECTRICAL

28LEMO $1.80 $1.98

LED MOUNTING CLIPSClip for panel mounting of 5mm LEDS. Pack of 10.

28LED $2.85 $3.14

LEDSSmall (5mm) light emitting diodes in 3 different colours: Red, Yellow and Green. Please specify colours when ordering.Pack of 10.

28BAHOS $1.70 $1.87

BATTERY HOLDER WITH INBUILT SWITCH

AA BATTERY HOLDER Holds 2 AA type batteries.

28BAHC $1.63 $1.79

D TYPE BATTERY HOLDER Holds single D type battery.

28BAHD $0.85 $0.94

BANANA SOCKETSA simple and quick way to convert a circuit, just push together. It is recommended that the leads should be soldered to the plug and base.

28BAPL $25.67 $28.24

LEADS MAGNETICMake working electrical circuits instantly with these leads fitted with a powerful magnet at either end. Place near a battery case and it connects by itself or place near a bulb holder connector and you have a working circuit. Children no longer have to strip wire and the leads can be daisy chained together to extend their length. Size: 300mm in length and the magnets protruding from the ends are 4mm. Pack of 10.

28LEMA $20.18 $22.20

28LEDF $2.85 $3.14

FLASHING RED LEDS5mm diameter, works with a 3V power source and is a very good low voltage flashing unit. Use for lighthouses, planes, etc. Price per each.

BATTERIES AA PACK OF 24“AA” type (Clock batteries) - Pack of 24.

28BATC $1.95 $2.15

BATTERIES C TYPE 1.5V PK 2“C” type 1.5 volt - Pack of 2.

28BATA $5.70 $6.27

BATTERIES C TYPE 1.5V ALKALINE (LONGER LASTING) “C” type 1.5 volt - Alkaline (longer lasting) Pack of 2.

28BATD $2.20 $2.42

BATTERIES D TYPE 1.5V PACK OF 2“D” type 1.5 volt - Pack of 2.

28BATCA $3.88 $4.27

BATTERIES 9 VOLT9 volt - sold each.28BAT9 $2.10 $2.31

28BATA

28BATD

28BAT9

28BATC

C TYPE BATTERY HOLDER Holds 2 C type batteries.

28BAHA $0.85 $0.94

BATTERY SNAP FOR 9 VOLT BATTERY9 volt battery clip.

28BASN $0.40 $0.44

28BAPL

28BASO

28LEMA

28LED

130

Te

ch

no

log

y

BATTERY CHARGER

28BACH $26.00 $28.60 28BATE $8.30 $8.3

BATTERY TESTER

GLOBES 2.5 VOLT

28GLECB $27.50 $30.25

GLOBE HOLDERS ECONOMICAL

Takes up to 5 batteries at once and is recommended for only rechargeable types.

Tests all battery types from 1.5 volt to 9 volt. Don’t throw any batteries away before you test them with this ingenious little gadget.

Ideal for lighting tops of towers, merry-go-rounds etc. 2.5 Volt. Pack of 10.

A very basic holder which will take 2.5V to 3V. Pack of 10.

ELECTRICAL

28CRPL $12.95 $14.25

CRIMPING PLIERS / WIRE CUTTERCombines a wire cutter and terminal crimper. Cuts wire 0.75 - 6.0mm.

CIRCUIT TESTERHave your own students made a correct circuit? Using this circuit tester, a single light will tell you.

28CITE $5.95 $6.55

GLOBE HOLDERS WITH WHITE BASEAn electrical mounting for 2.5 volt lamps. Pack of 10.

28GLHO $9.20 $10.12

28CON $11.16 $12.28

CONNECTOR TABSCan be soldered or squeezed onto wires, to provide easy connection to motors and globe holders. Pack of 100.

CLOCK MECHANISMS

Peel off and stick on, gold clock numerals. Each sheet contains enough numerals for five clocks.

28GLOBB $38.25 $42.08

28WIST $10.00 $11.00

WIRE STRIPPERSWith self adjusting mechanism that allows stripping of PVC insulated wire from .5mm to 6mm in size without damaging the conductor. The stripping length is adjustable from approx. 3mm to 25mm, and manual adjustment is available. With in-built cable cutter.

28WIRE1B $9.10 $10.01

WIRE CABLE RED1mm thick. 100 metres per coil of single colour. Red.

28CLNUG $3.50 $3.85

CLOCK NUMERALS GOLD PEEL & STICK

GLOBES 2.5 VOLT PACK 1002.5 Volt - Bulk pack of 100.

28GLOB $4.25 $4.68 28GLEC $3.05 $3.36GLOBE HOLDERS ECONOMICAL PACK 100

WIRE CABLE BLACK1mm thick. 100 metres per coil of single colour. Black.

28WIRE1R $9.10 $10.01

28CLNU3D $1.20 $1.32

3D CLOCK NUMBERS

A very basic holder which will take 2.5V to 3V. Pack of 100.

28WIST

Te

ch

no

log

y

131

CLOCK MECHANISMS

MOTOR DRIVE UNITIngenious worm-gear reduction gearbox which connects to the standard motor. (price does not include motor) Supplied with four washers, two on each screw to prevent them touching the commutator.

28MODR $6.60 $7.26

3 VOLT MOTOR

28MOTO9 $1.20 $1.32

MINI BUSHES PUSH FIT ONTO SHAFT OF 3 VOLT MOTORUse with gear and pulley bargain pack.Pack of 20.

Approximately 11,000 revs per minute.

MOTOR SPINDLE GEAR DRIVEFits all motors with 2mm output shaft. Universal design feature for use as either a 10T pinion or a small pulley drive. Pack of 20.

28MOSP $4.40 $4.84

28BUMI $9.10 $10.01

28CLME7H $4.95 $5.45

CLOCK MECHANISM 7MM WITH HANGERClock mechanism with a 7mm shaft, includes hanger.

CLOCK MECHANISM 7MM WITHOUT HANGERClock mechanism with a 7mm shaft, without hanger.28CLME7 $4.95 $5.45

28CLME12H $4.95 $5.45

CLOCK MECHANISM 12 WITH HANGERClock mechanism with a 12mm shaft, includes hanger.

28CLHAG $0.50 $0.55

CLOCK HANDS GOLDClock hands, hour, minute & second hand set. Gold. 50/65mm.

28CLME12 $4.95 $5.45

CLOCK MECHANISM 12 WITHOUT HANGERClock mechanism with a 12mm shaft, without hanger.

28CLHAB $0.50 $0.55

CLOCK HANDS BLACKClock hands, hour, minute & second hand set. Black. 50/65mm.

MOTORS - ELECTRICAL

28MOTO $1.20 $1.323 VOLT MOTOR BULK PRICE Per each for 100+

9 VOLT MOTOR28MOTOB $1.10 $1.21

MOTOR CLIPSPush fit plastic clip which secures the standard motor. Has self adhesive pad on the base for easy mounting. Pack of 10.28MOCL $9.30 $10.23

28MOMO $14.64 $16.10

MOTOR MOUNTSMotor Mounts. Pack of 10.

MOTOR - WIND UPSupplied with an axle & pull string. Mount on chassis, add wheels, pull string then release to propel car.

28GEWIP $2.50 $2.75

CAR KIT 1 WITH SWITCH & BATTERIES SET

28CKIT1 $100.19 $110.21

SET OF 20. Includes: Balsa chassis, Solar motor, Solar panel, Bamboo skewer axle, 37mm Wheels, Gears & Pinions & Plastic straws.

CAR KIT 2 WITH SOLAR PANEL SET

28CKIT2 $166.19 $182.81

28MOCL

28MOMO

Materials Required But Not Supplied In Kit. Hot Melt Glue Gun, Scissors & Wire Strippers, Solder & Soldering Iron.

SET OF 20. Includes: Balsa chassis, 3V Motor, AA Battery holder with switch, Bamboo skewer axle, 37mm Wheels, Gears & Pinions & Plastic straws. Batteries not included.Materials Required But Not Supplied

In Kit. Hot Melt Glue Gun, Scissors & Wire Strippers, Solder, Soldering Iron & Aa Batteries.

CAM’S BATTERY POWERED & SOLAR POWERED CAR KITS

132

Te

ch

no

log

y

POTENTIOMETERS - (Speed Control Switch)

28POT $1.90 $2.09 28SWID $2.30 $2.53

DOUBLE POLE SWITCH

MICRO SWITCH

28PTSW $1.40 $1.54

PUSH SWITCH

To reduce or increase the power of a light or sound cource by turning up or down slowly. 10K ohms.

2 position switch. Can control 2 separate circuits.

Requires very little pressure or movement.

Identified by a red cap, this switch will only make a contact for as long as it is physically pushed.

28MISW $1.89 $2.08

SWITCHES

28SWI3 $2.95 $3.25

THREE POSITION SWITCHThree position, double pole toggle switch with a centre off position.

SLIDE SWITCH 3 POSITION DOUBLE POLE3 position, double pole slide switch. Has a centre off position. On/Off/On.

28SDPDT $1.20 $1.32

REMOTE STOP & GO SWITCH

28REMOT $2.50 $2.75

28SWSLM $0.80 $0.88

SLIDE SWITCH MINI2 position, double pole - On/Off.

GEARS BARGAIN PACKA packet of 80 assorted gears, plus five racks. Made from sturdy plastic.

Forward/Reverse remote control with wire. Green button for forwards, Red button for reverse.Release both buttons for stop. Uses two 1.5V ‘AA’ Batteries (not included). Use with 3V motor & gearbox.

28SWIP $2.05 $2.26

28GEPA $16.85 $18.54

SINGLE POLE SWITCH2 position switch. On/Off.

28BUZ $4.85 $5.34

BUZZERComplete with positive and negative wire attached.

GEARS

GEARBOX WITH MOTOR & AXLEMount onto a Card or Balsa wood chassis.

28GBMA $2.50 $2.75

Te

ch

no

log

y

133

GEARS HEAVY DUTYTough plastic Module 1 gears in a range of sizes all with 4mm centre holes which accept 4mm dowelling or steel rod. The centre holes can be reduced to 2mm by using the push fit nylon insert reducer. The gears are also available with a locking brass bush.

GEARS

GEARS FINE TOOTH WHITE PLASTICFine tooth Gear and pinion now sold separately. Perfect for gearing a small car. Pinon push fits onto pin of motor. Use with 2.5mm axle rod.

28PULLEY $17.50 $19.25

PULLEY BARGAIN PACKPack of 24 assorted pulleys, containing three sizes : 29mm, 42mm, and 52mm, with 4mm centre holes.

PULLEYS

Will fit directly onto electric motor with insert provided. The following come with brass centres and grub screws. Packets of 5.

PULEYS HEAVY DUTYTough plastic pulleys with a 4mm centre hole. Centre holes can be reduced to 2mm using our push fit mini bush reducer. Packets of 5.

28PULL40 $14.25 $15.68

10 MM

40 MM

28PULL10 $8.45 $9.30

28PULL60 $16.40 $18.04

20 MM

60 MM

28PULL20 $8.95 $9.85

28GEPF20 $6.95 $7.65

20 TOOTH 20MM Pack of 528GEPF30 $8.30 $9.13

30 TOOTH 30MM Pack of 528GEPF40 $9.70 $10.67

40 TOOTH 40MM Pack of 5

28GEPF50 $11.10 $12.21

50 TOOTH 50MM Pack of 528GEPF60 $12.45 $13.70

60 TOOTH 60MM Pack of 5

GEARS WITH BRASS HUBA range of Module 1 spur gears with brass hubs and locking grub screw. All gears have 4mm running centre holes. Module 1 gears have the same number of teeth as the diameter of the gear ie. 15 tooth = 15mm diameter.

28GE10 $11.06 $12.17

10 TOOTHPack of 5

28GE20 $16.60 $18.26

20 TOOTHPack of 5

28GE30 $18.25 $20.08

30 TOOTH Pack of 5

28GE40 $19.40 $21.34

40 TOOTH Pack of 5

28GE50 $20.75 $22.83

50 TOOTH Pack of 5

28GEB45 $21.30 $23.43

BEVEL GEAR 45 TOOTH Pack of 4

28GEFT5 $4.00 $4.40

50 TOOTH DIAM 26MM

28GEPI $4.00 $4.40

GEARS PINION 12 TOOTHGear size: 50/10 tooth. Pack of 10 gears.

Pinion 12 tooth. Pack of 10.

28PUHD10 $9.55 $10.51

10MM Pack of 528PUHD20 $9.55 $10.51

20MM Pack of 528PUHD30 $9.55 $10.51

30MM Pack of 5

28PUHD40 $9.55 $10.51

40MM Pack of 528PUHD60 $9.55 $10.51

50MM Pack of 5

PULLEYS WITH BRASS CENTRE

134

Te

ch

no

log

y

PULLEY PACKS - WOODEN

PULLEY BLOCKS

Hardwood, wooden pulleys. Ideal for all kinds of design and make projects. Pulleys come in various diameters and are all 10mm thick with a 4mm centre hole. Pack of 10.

These pulley blocks have 50mm nylon pulleys in a metal frame with hooks top and bottom. Sold per each.

PULLEYS

28PROP $8.00 $8.80

PROPELLER 130 MM2 bladed with centre boss that push fits onto an electric motor. Size 130mm. Pack of 10.

PROPELLER 127MMIn order for the propeller to fit to the shaft of a 3 volt electric motor spindle, you need 6mm of rubber universal joint. (Universal joint, see Marine Assembly).Pack of 6.

28PROC $11.95 $13.15

PROPELLER 3 BLADES 110MM DIAM

28PRO3 $8.00 $8.80

28PRASC2 $5.00 $5.50

UNIVERSAL JOINT USE WITH 28PROCLength 30cm for use with 28PROC. *Please note, economical universal joint unsuitable.

MARINE BOAT PROPELLER UNIT AThis unit is for boats, designed to hook up to our electrical motors. This assembly comprises the following items:-28PRASA, 28PRASB, 28PRASCand 28PRASD.

Approx. 110mm diameter with a centre boss. It push fits directly onto our 3 volt motor with plastic wrap between propeller and motor shaft.

PROPELLERS

28PUW040 $12.50 $13.75

20 MM DIAM

40 MM DIAM

28PUW020 $8.90 $ 9.79

28PUW050 $18.20 $20.02

30 MM DIAM

50 MM DIAM

28PUW030 $9.90 $10.89

28PBTR $12.32 $13.55

PULLEY BLOCKS SINGLE

PULLEY BLOCKS TREBLE

28PBSI $7.84 $8.62

28PBQU $14.56 $16.02

PULLEY BLOCKS DOUBLE

PULLEY BLOCKS QUAD

28PBDO $10.08 $11.09

IMPORTANT! - Please ensure propellers are properly fitted to the motor shaft or they may spin off and cause injury!

28IMP $2.36 $2.60

SOLAR IMPELLER 4 BLADEDApproximately 5.5cm diameter wide. Will push fit directly onto the pin of the 3 and 9 volt motors.

28PROUC $11.95 $13.15

PROPELLER MARINE UNIT BInner shaft: 24cm x 2mm with threaded end. Outer cover: Brass tube 5mm diam. x 22.5cm long with Plastic end pieces fitted. Propeller: 3 bladed black plastic 2.5cm diam with threaded brass insert to take inner shaft.

28PRASE $0.97 $1.0728PRASA $2.50 $2.75

30CM UNIVERSAL JOINT

INNER SHAFT LENGTH 150MM

OUTER TUBE LENTH 140MM

UNIVERSAL JOINT ECONOMY 1 METRE

28PRASB $2.50 $2.75

28PRASC2 $5.00 $ 5.503CM LENGTH RUBBER TUBING UNIVERSAL JOINT28PRASC $0.50 $0.55

28PROU $5.00 $5.50

3 BLADED PROP 18.5MM DIAMETER28PRASD $0.25 $ 0.28

28PROU

Te

ch

no

log

y

135

ROBO ANT

28RBANT $21.50 $23.65

The Roboant is a small robot that will follow dark lines against a white background.

A simple robot project that illustrates the use of phototransistors and the response to a light source. This robot has been named the moth, as it is drawn to the light source. It is particularly appealing for younger students introduction to Robotics. Version 1 - requires no soldering.

TECHNOLOGY KITS

ROBO BAT (Moves away from light)

This robot is similar to the Robomoth, but moves away from the light source. Version 1 - requires no soldering.

28RBBA1 $10.50 $11.55

28TKAT $15.98 $17.58

AIR TRIKE KITBuild a futuristic propeller powered trike with this timber slot assembly kit.

28TKCH $15.98 $17.58

CHOPPER KIT

28BABE8A $6.09 $6.70

BALL BEARINGS 8MM

28BABE12A $8.48 $9.33

BALL BEARINGS 12MM

ROBO MOTH (Moves away from light)

28RBMO1 $10.50 $11.55

ROBO MOTH (REQUIRES SOLDERING)

28RBMO2 $8.95 $9.85

Version 2 - Advanced - requires soldering.

ROBO BAT (REQUIRES SOLDERING)

Version2-Advanced-requires soldering.28RBA2 $8.95 $9.85

TECHNO KITS

28TKCV $15.98 $17.58

STUNT BUGGY KITUse the pre-cut wooden pieces to build a fast little buggy that does wheelies. Great fun! No glue, no mess and easy to assemble.Learn about motion theories and gear weight ratios.

28FLIGHT $22.86 $25.15

FLIGHT SCHOOL KIT

Build your own glider and fly it.

28TRIWH $13.20 $14.52

TRI WHEELER SCOOTER KIT

28RACER $13.20 $14.52

BIG WHEEL RACER KIT

28WALDI $16.83 $18.51

WALKING DINOSAUR KIT

BALL BEARINGS TECHNOLOGY GENERAL

28MARB $3.60 $3.96

MARBLES

TECHNO KITSThese kits are a fun way for children to learn about electrical, mechanical, energy and force & motion concepts.Suits Grade 3 and up.

Build an electric chopper. Create your own car and race them against your friends. Some soldering required.

Build your own Dinosaur. Kit includes all parts and one motor. Some soldering required.

This chassis allows for the attachment of external panels made from cardboard, which can be coloured to create exciting designs.Some soldering required.

Pack of 80.8mm. Pack of 10.

12mm. Pack of 10.