The CaP is the onlyconnector worldwide to be:

simple and quick

universal for any cable

economical

reusable and recyclable

patented

made in Italy

mechanically strong

electronically superior

available in 9 colours

be able with cable

CaP, Pressure Connector

The CaP, patented heart of the CaP System, is a revolutionary non-metallic F male connector designed to make every coaxial termination simple, quick and reliable and to drastically reduce all typical problems which arise in terminating coaxial cables.CaP, used with our speci�c adapters (see Sheet A), becomes a connector usable in all existing coaxial standards.CaP, applied directly on any device equipped with F female connectors (see Sheet B), allows for the best possible quality connection.

CaP SystemThe 30-Second ConnectorYou Can’t Screw Up!

Viale Stefano Tinozzi, snc - Zona Ind.le Interporto d’Abruzzo - 65024 Manoppello (PE) - ITALYTel. +39 085 8569020 - Fax +39 085 8569707www.telecomsecurity.it - info@telecomsecurity.it - Skype: telecomsecurity_info

be able with cable

The CaP is the onlyconnector worldwide to be:

simple and quick

universal for any cable

economical

reusable and recyclable

patented

made in Italy

mechanically strong

electronically superior

available in 9 colours

be able with cable

CaP, Pressure Connector

The CaP, patented heart of the CaP System, is a revolutionary non-metallic F male connector designed to make every coaxial termination simple, quick and reliable and to drastically reduce all typical problems which arise in terminating coaxial cables.CaP, used with our speci�c adapters (see Sheet A), becomes a connector usable in all existing coaxial standards.CaP, applied directly on any device equipped with F female connectors (see Sheet B), allows for the best possible quality connection.

CaP SystemThe 30-Second ConnectorYou Can’t Screw Up!

Viale Stefano Tinozzi, snc - Zona Ind.le Interporto d’Abruzzo - 65024 Manoppello (PE) - ITALYTel. +39 085 8569020 - Fax +39 085 8569707www.telecomsecurity.it - info@telecomsecurity.it - Skype: telecomsecurity_info

be able with cable

Insert the coaxial cable intothe side slot of the strippingtool (SPC) about 1cm (5/8”); gently squeeze the blades while pulling the cable out to slit both sides of the jacket.

Slide the CaP on to the coaxial cable.

1

2

Insert the cable in the square hole until the dielectric just peaks through the small round holeon the other side.Rotate the tool ± 90° while squeezing the blades to cut and remove the dielectric.

4

Expose the dielectricby pushing backwardsthe jacket and the braid.

3

tutorial

Cable preparationFrom RG179 to RG6 Quad Shield

From micro coaxial to 7 mm cables

Many cables,one solutionUp to today every model/dimension of cable has its speci�c model of connector.CaP solves this problem: thanks to its unique features, the CaP can be used with any coaxial cable (from miniature coaxial through RG6 Quad, 50 or 75 Ohm impedance, plenum or not, with any type of shielding or braid, indoor or outdoor, …).CaP is the one and only connector formany cables!

One solution,many applicationsThanks to its versatility, CaP can be used in many applications and industries: from Terrestrial and Satellite TV to Home Theatre systems, from Video Surveillance to Broadcasting, from Telecommunication Networks to RF Instruments, to Custom Cabling.Everywhere a coaxial cable is used, the CaP �nds an advantageous application. 6-b

5-b

Terminate connection with ProCaP

REMOVALWith the ProCaP fully open, insert the connector groove in the middle �ngers and squeeze the handles to open the connection.

6-a

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it. Lay the coaxial cable through the �at side of the professional pliers (ProCaP). Slip the connector groove in the �ngers on the far side.Gently squeeze the pliers to secure the connector. Unlike compression connectors, CaP does not require force.

5-a

tutorial

tutorial

Terminate connection with PiCaP

REMOVALInsert the connector groove in the �ngers (closed) at the top of the PiCaP and squeeze the handles to open the connection.

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it.Insert the connector between the handles tips of the economic pliers (PiCaP).To terminate the connection squeeze the handles, placing your hand near the connector to obtain greater leverage.

ONLY 1 CONTACT POINT!

CaP connectionCable braid connects directly to the end user with only 1 contact point.

-60.00

-50.00

-40.00

-30.00

-20.00

dB

-140.0

-120.0

-100.0

-80.00

-60.00

dB

EN 50117 Screening Class A++

1 2 3 GHz 1 2 3 GHz

RETURN LOSSSCREENING EFFECTIVENESS

CaP vs F metal

CaP electrical characteristics

CaP

- - -

- - -

- -

1 2 2/3 2/3/4

1 3 3 3

screw-on crimp compression

lowhigh medium high

slowfast medium fast

plastic material “transparent”for electrical connection

number of parts

compatibility with di�erentdiameter cables

number of contact points

pull-out resistance

installation time

lowlow medium highcost

reusability

3 CONTACTS

F metal connectionCable braid connects to the end user through 3 contact points, raising the signal losses and creating greater interferences.

IECm

Ff HQFf

BNCm BNCf

IECf

RCAm RCAf

Fm a vite Fm a vite 90°

Sheet A

Fm rapido Fm rapido 90°

BNCm HQ

Features of our adapters

Our adapters have been speci�cally designed to reach optimal performances when used with the CaP, thanks to their unique features:central groove: to allow for a solid engagement with the pliers during installation and removal;internal structure: speci�c dielectric and elastic yet strong clip, to have a better contact with a large range of conductors;external body: single and compact element, to have smaller dimensions and lower signal losses.

CaP as a coaxial connector

When used with our speci�c F female adapters, CaP becomes a coaxial connector in any available standard (IEC, RCA, BNC, F, ..), male or female, straight or right angle, 50 or 75 Ohm.

For high professional use it is now available our BNC HQ male adapter (Return Loss > 30 dB @ 3 GHz).

ONLY 1 CONTACT POINT!

CaP connectionCable braid connects directly to the end user with only 1 contact point.

-60.00

-50.00

-40.00

-30.00

-20.00

dB

-140.0

-120.0

-100.0

-80.00

-60.00

dB

EN 50117 Screening Class A++

1 2 3 GHz 1 2 3 GHz

RETURN LOSSSCREENING EFFECTIVENESS

CaP vs F metal

CaP electrical characteristics

CaP

- - -

- - -

- -

1 2 2/3 2/3/4

1 3 3 3

screw-on crimp compression

lowhigh medium high

slowfast medium fast

plastic material “transparent”for electrical connection

number of parts

compatibility with di�erentdiameter cables

number of contact points

pull-out resistance

installation time

lowlow medium highcost

reusability

3 CONTACTS

F metal connectionCable braid connects to the end user through 3 contact points, raising the signal losses and creating greater interferences.

IECm

Ff HQFf

BNCm BNCf

IECf

RCAm RCAf

Fm a vite Fm a vite 90°

Sheet A

Fm rapido Fm rapido 90°

BNCm HQ

Features of our adapters

Our adapters have been speci�cally designed to reach optimal performances when used with the CaP, thanks to their unique features:central groove: to allow for a solid engagement with the pliers during installation and removal;internal structure: speci�c dielectric and elastic yet strong clip, to have a better contact with a large range of conductors;external body: single and compact element, to have smaller dimensions and lower signal losses.

CaP as a coaxial connector

When used with our speci�c F female adapters, CaP becomes a coaxial connector in any available standard (IEC, RCA, BNC, F, ..), male or female, straight or right angle, 50 or 75 Ohm.

For high professional use it is now available our BNC HQ male adapter (Return Loss > 30 dB @ 3 GHz).

Insert the coaxial cable intothe side slot of the strippingtool (SPC) about 1cm (5/8”); gently squeeze the blades while pulling the cable out to slit both sides of the jacket.

Slide the CaP on to the coaxial cable.

1

2

Insert the cable in the square hole until the dielectric just peaks through the small round holeon the other side.Rotate the tool ± 90° while squeezing the blades to cut and remove the dielectric.

4

Expose the dielectricby pushing backwardsthe jacket and the braid.

3

tutorial

Cable preparationFrom RG179 to RG6 Quad Shield

From micro coaxial to 7 mm cables

Many cables,one solutionUp to today every model/dimension of cable has its speci�c model of connector.CaP solves this problem: thanks to its unique features, the CaP can be used with any coaxial cable (from miniature coaxial through RG6 Quad, 50 or 75 Ohm impedance, plenum or not, with any type of shielding or braid, indoor or outdoor, …).CaP is the one and only connector formany cables!

One solution,many applicationsThanks to its versatility, CaP can be used in many applications and industries: from Terrestrial and Satellite TV to Home Theatre systems, from Video Surveillance to Broadcasting, from Telecommunication Networks to RF Instruments, to Custom Cabling.Everywhere a coaxial cable is used, the CaP �nds an advantageous application. 6-b

5-b

Terminate connection with ProCaP

REMOVALWith the ProCaP fully open, insert the connector groove in the middle �ngers and squeeze the handles to open the connection.

6-a

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it. Lay the coaxial cable through the �at side of the professional pliers (ProCaP). Slip the connector groove in the �ngers on the far side.Gently squeeze the pliers to secure the connector. Unlike compression connectors, CaP does not require force.

5-a

tutorial

tutorial

Terminate connection with PiCaP

REMOVALInsert the connector groove in the �ngers (closed) at the top of the PiCaP and squeeze the handles to open the connection.

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it.Insert the connector between the handles tips of the economic pliers (PiCaP).To terminate the connection squeeze the handles, placing your hand near the connector to obtain greater leverage.

Insert the coaxial cable intothe side slot of the strippingtool (SPC) about 1cm (5/8”); gently squeeze the blades while pulling the cable out to slit both sides of the jacket.

Slide the CaP on to the coaxial cable.

1

2

Insert the cable in the square hole until the dielectric just peaks through the small round holeon the other side.Rotate the tool ± 90° while squeezing the blades to cut and remove the dielectric.

4

Expose the dielectricby pushing backwardsthe jacket and the braid.

3

tutorial

Cable preparationFrom RG179 to RG6 Quad Shield

From micro coaxial to 7 mm cables

Many cables,one solutionUp to today every model/dimension of cable has its speci�c model of connector.CaP solves this problem: thanks to its unique features, the CaP can be used with any coaxial cable (from miniature coaxial through RG6 Quad, 50 or 75 Ohm impedance, plenum or not, with any type of shielding or braid, indoor or outdoor, …).CaP is the one and only connector formany cables!

One solution,many applicationsThanks to its versatility, CaP can be used in many applications and industries: from Terrestrial and Satellite TV to Home Theatre systems, from Video Surveillance to Broadcasting, from Telecommunication Networks to RF Instruments, to Custom Cabling.Everywhere a coaxial cable is used, the CaP �nds an advantageous application. 6-b

5-b

Terminate connection with ProCaP

REMOVALWith the ProCaP fully open, insert the connector groove in the middle �ngers and squeeze the handles to open the connection.

6-a

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it. Lay the coaxial cable through the �at side of the professional pliers (ProCaP). Slip the connector groove in the �ngers on the far side.Gently squeeze the pliers to secure the connector. Unlike compression connectors, CaP does not require force.

5-a

tutorial

tutorial

Terminate connection with PiCaP

REMOVALInsert the connector groove in the �ngers (closed) at the top of the PiCaP and squeeze the handles to open the connection.

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it.Insert the connector between the handles tips of the economic pliers (PiCaP).To terminate the connection squeeze the handles, placing your hand near the connector to obtain greater leverage.

Splitter/Tap Coaxial outlet

Multiswitch

LNB

Antenna

Sheet B

CaP as an F male connectorCaP is a direct replacement of a traditional F male connectors, either screw-on, crimp or compression type, so it can be used to connect directly to any device equipped with F female connectors.By not using the standard F metal connector you take away the main part of the connection therefore you remove all interferences in the radiofrequency signal transmission.CaP, being non-conductive, is the best and only solution to �rmly connect a cable to a device, with a single and direct contact of both centre conductor and braid.

6-c

5-c

tutorial

Terminate connection with Pu-PuCaPTo allow for an easier installation of the CaP onto large devices, in restricted spaces or when F female connectors are placed very closed together, we developed a speci�c inserter/extractor tool (Pu-PuCaP).

REMOVALHook the Pu-PuCaP on the CaP by means of the speci�c groove of the tool.Swing and at the same time pull down the Pu-PuCaP up to the complete disconnection of the CaP and cable from the device.

INSTALLATIONInsert the CaP in the speci�c groove positioned at the top of the Pu-PuCaP and insert the central conductor into the F female connector.Slide the CaP over the F female, thus folding the braid and jacket over the thread.Terminate the connection by swinging and at the same time pushing forward the Pu-PuCaP up to the complete insertion of the CaP onto the F female connector.

Insert the coaxial cable intothe side slot of the strippingtool (SPC) about 1cm (5/8”); gently squeeze the blades while pulling the cable out to slit both sides of the jacket.

Slide the CaP on to the coaxial cable.

1

2

Insert the cable in the square hole until the dielectric just peaks through the small round holeon the other side.Rotate the tool ± 90° while squeezing the blades to cut and remove the dielectric.

4

Expose the dielectricby pushing backwardsthe jacket and the braid.

3

tutorial

Cable preparationFrom RG179 to RG6 Quad Shield

From micro coaxial to 7 mm cables

Many cables,one solutionUp to today every model/dimension of cable has its speci�c model of connector.CaP solves this problem: thanks to its unique features, the CaP can be used with any coaxial cable (from miniature coaxial through RG6 Quad, 50 or 75 Ohm impedance, plenum or not, with any type of shielding or braid, indoor or outdoor, …).CaP is the one and only connector formany cables!

One solution,many applicationsThanks to its versatility, CaP can be used in many applications and industries: from Terrestrial and Satellite TV to Home Theatre systems, from Video Surveillance to Broadcasting, from Telecommunication Networks to RF Instruments, to Custom Cabling.Everywhere a coaxial cable is used, the CaP �nds an advantageous application. 6-b

5-b

Terminate connection with ProCaP

REMOVALWith the ProCaP fully open, insert the connector groove in the middle �ngers and squeeze the handles to open the connection.

6-a

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it. Lay the coaxial cable through the �at side of the professional pliers (ProCaP). Slip the connector groove in the �ngers on the far side.Gently squeeze the pliers to secure the connector. Unlike compression connectors, CaP does not require force.

5-a

tutorial

tutorial

Terminate connection with PiCaP

REMOVALInsert the connector groove in the �ngers (closed) at the top of the PiCaP and squeeze the handles to open the connection.

INSTALLATIONInsert the centre conductor into the F female connector and fold the braid and jacket over the thread by sliding the CaP over it.Insert the connector between the handles tips of the economic pliers (PiCaP).To terminate the connection squeeze the handles, placing your hand near the connector to obtain greater leverage.

Splitter/Tap Coaxial outlet

Multiswitch

LNB

Antenna

Sheet B

CaP as an F male connectorCaP is a direct replacement of a traditional F male connectors, either screw-on, crimp or compression type, so it can be used to connect directly to any device equipped with F female connectors.By not using the standard F metal connector you take away the main part of the connection therefore you remove all interferences in the radiofrequency signal transmission.CaP, being non-conductive, is the best and only solution to �rmly connect a cable to a device, with a single and direct contact of both centre conductor and braid.

6-c

5-c

tutorial

Terminate connection with Pu-PuCaPTo allow for an easier installation of the CaP onto large devices, in restricted spaces or when F female connectors are placed very closed together, we developed a speci�c inserter/extractor tool (Pu-PuCaP).

REMOVALHook the Pu-PuCaP on the CaP by means of the speci�c groove of the tool.Swing and at the same time pull down the Pu-PuCaP up to the complete disconnection of the CaP and cable from the device.

INSTALLATIONInsert the CaP in the speci�c groove positioned at the top of the Pu-PuCaP and insert the central conductor into the F female connector.Slide the CaP over the F female, thus folding the braid and jacket over the thread.Terminate the connection by swinging and at the same time pushing forward the Pu-PuCaP up to the complete insertion of the CaP onto the F female connector.

The CaP is the onlyconnector worldwide to be:

simple and quick

universal for any cable

economical

reusable and recyclable

patented

made in Italy

mechanically strong

electronically superior

available in 9 colours

be able with cable

CaP, Pressure Connector

The CaP, patented heart of the CaP System, is a revolutionary non-metallic F male connector designed to make every coaxial termination simple, quick and reliable and to drastically reduce all typical problems which arise in terminating coaxial cables.CaP, used with our speci�c adapters (see Sheet A), becomes a connector usable in all existing coaxial standards.CaP, applied directly on any device equipped with F female connectors (see Sheet B), allows for the best possible quality connection.

CaP SystemThe 30-Second ConnectorYou Can’t Screw Up!

Viale Stefano Tinozzi, snc - Zona Ind.le Interporto d’Abruzzo - 65024 Manoppello (PE) - ITALYTel. +39 085 8569020 - Fax +39 085 8569707www.telecomsecurity.it - info@telecomsecurity.it - Skype: telecomsecurity_info

be able with cable