car builder solutions · without sidelight. moulded abs half bowl nest for maximum mounting...

CBS CATALOGUE ISSUE 33 UPDATE

CAR BUILDER

To order visit our online shop www.carbuilder.com

or Tel: 01580 891309 or 07964 336183

SOLUTIONSISSUE 33

UPDATEPAGES

STAPLE THESE PAGES TO THE BACK PAGE OF YOUR

ISSUE 33 CATALOGUE

NOVEMBER. 2019


BADGE BARS 19mm diameter, polished stainless steel tube with stainless end plugs. End plugs are not fitted so tube can easily be shortened. Chrome plated, diecast mounts with stainless fixing bolt and rubber gasket. Stainless grubscrew in the mount secures it to the tube with an allen key. Four versions1. 235mm tube with single mount#BADGE235 £13 (£15.60 inc vat)2. 615mm straight tube with two mounts.#BADGE615 £22 (£26.40 inc vat)3. 615mm curved tube with two mounts.#BADGECUR £22 (£26.40 inc vat)

4. 565mm straight tube with two chromed flat plate mounts. 140mm x 34mm with a 9mm hole.#BADGE565 £22 (£26.40 inc vat)

1

2

3

4

4

20mm

FOOTPRINT 29mm x 21mm

4

2

98mm1

BADGE MOUNTING CLIPThis polished stainless clip is a perfect fit around our Badge Bar Tubes. Slotted holes for badge holes between 14mm and 25mm centres. Size 38mm wide x 36mm high.Stainless screws, washers and nuts included#BMC £3.50 (£4.20 inc vat)

3


PORSCHE 356A REAR LIGHTS Handed Pair. These very nice lights are direct replacements for the original 356 items but they may fit other vehicles with some ingenuity. The pressed steel body and rubber surround accurately match the double curvature of the Porsche body. The Chrome bezel and lens is retained with chrome screws in brass inserts. Stop, Tail and Indicator bulbs are included. Size 195mm x 75mm. Three M5 mounting studs with nuts. 200mm flyleads for live supplies. NOTE: These lamps require an earth - either through contact with the vehicle’s metal body or with a separate earth wire connected to the lamp housing. Weight 665gms./pair.#RL132 £100 pair (£120 inc vat)

PORSCHE STYLE DOOR MIRRORVery sleek and stylish door or wing-mounted mirror. Chromed mirror head, size - 125mm x 93mm with flat glass. Limited (3 degrees) head adjustment. Chromed, diecast arm with black plastic stand-off / gasket. Base footprint 125mm x 25mm. Two M6 studs at 64mm centres with nuts and washers Weight 420gms.#M34 £35 each (£42 inc vat)

BLADE PARK TWIN WASHER JETMounts through a 10mm hole with rubber washers and brass nut. 5mm push-on hosetail. Overall length 84mm. Height above panel 35mm. Clearance under overhang 24mm. Weight 21gms.#WJET7 £3 (£3.60 inc vat)

24mm

SMOOTH FINISH NACA DUCTS Smooth Satin Black finish, vacuum moulded ABS. Can be riveted or bonded to body either inside or outside. Can be painted. Material thickness approximately 2mm. May be supplied with trimmed front opening.Dimensions including flange: LARGE - 235mm x 190mm x 45mm high. SMALL - 180mm x 145mm x 25mm high.LARGE BLACK SMOOTH NACA #NACA1S SMALL BLACK SMOOTH NACA #NACA2S Both £10 each (£12 inc vat)


SEQUENCING AMBER LED STALK INDICATORS WITH BUILT IN FLASHER RELAY. ‘E8’ Marked. IVA OK. This unique, smoked lens lamp has a row of LEDs that illuminate in sequence on every flash. Each lamp also has a built in flasher relay so, if four lamps are used, front and rear, the wiring can be really simple. The 20mm long, M8 mounting stud has a flexible rubber joint to the lamp so it will flex, not break on impact. Length 95mm excluding stud. 15mm high and 25mm front to back. 200mm sleeved flyleads with male bullet connectors. See a video of them in action on our online listing. #SI032 £29 pair (£34.80 inc vat)

SEE A VIDEO ON OUR

YOUTUBE CHANNEL

VHT AEROSOL ENGINE PAINT Gloss finish. Resists fuel, oil & solvents. Will withstand up to 550ºF . Net weight 11 ounces (311 gms)FORD GREY #PNENFGY £8.50 (£10.20 inc vat)

FOUR OUTLET MIDIVAL FUSE DISTRIBUTION BOX This box accepts one MEGAVAL fuse on the input side between two M8 studs and four, MIDIVAL fused outlets from a common busbar. Size 87mm x 116mm x 38mm high. Clip-on lid. Two 5mm mounting holes at 98mm centres. Weight 182gms. FUSES AND CABLES NOT INCLUDED#MFDB4 £20 (£24 inc vat)

FUSES AND CABLES NOT INCLUDED

SHOWN FOR EXAMPLE ONLY

100 AMP MEGAVAL FUSE #MEGV100 £2.50 each (£3 inc vat)

100mm DIAMETER DRIVING LIGHTS WITH BRACKET ‘E4’ Marked, 12 volt. 55 watt Halogen bulb fitted. Glass lens bonded to diecast alloy housing. Adjustable, powder-coated steel mounting bracket. Overall height with bracket 115mm. Front to back 70mm. 75mm flyleads with 1/4” male spade terminals. Weight 770gms. pair.#DRVLT17 £20 pair (£24 inc vat)

PLEASE HELP US PROCESS YOUR ORDER MORE

EFFICIENTLY BY MAKING A LIST OF

PART NUMBERS BEFORE YOUR CALL

OR VISIT


75mm DIAMETER LED REAR LIGHTS‘E24’ Marked, sealed lamps. Fit in a 55mm hole. Two 3.9mm diameter fixing holes at 66mm centres. 26mm front projection. 30mm rear projection. 80mm long flyleads with two or three pin plug. Weight 90gms each.STOP / TAIL 2.2 watt and 0.5 watt. 3 wire.#RL133 £50 pair (£60 inc vat)

INDICATOR 4 watt 2 wire#RL134 £50 pair (£60 inc vat)

REVERSE 4.3 watt 2 wire#RL135 £50 pair (£60 inc vat)

123mm DIAMETER REFLECTOR LAMP HOUSING ‘E1’ Marked, Surface mounting with a 97mm diameter x 22mm deep recess for 95mm diameter rear lamps. Multiple mounting holes. Weight 68gms.HOUSING ONLY. LAMPS NOT INCLUDED#REF122 £12 each (£14.40 inc vat)

SHOWN WITH #RL61C

SHOWN WITH #RL17ST

EXAMPLES

Our #WPMUL2 and #WPMUL3 packs contain suitable female connectors

TAPERED REAMER SET You’ll find a multitude of jobs for this handy kit. From enlarging and cleaning dashboard holes for switches and warning lights to correcting misaligned holes in chassis brackets. Suitable for Steel, Aluminium, GRP, Acrylics and Wood. Two heat-treated, High Carbon Steel Hand Reamers with ’T’ Handles.3mm to 12mm at 5 degrees angle.and 3mm to 16mm at 10 degrees angle.#TAPERREAM £7.50 (£9 inc vat)

30mm CHROMED AERIAL BLANKING CAP This discreet little 30mm diameter, domed plate will seal and blank-off old aerial holes between 20mm and 22mm diameter in any thickness bodywork. Install from above and tighten the M6 nut beneath. Weight 24gms.#AERBLANK £4.50 (£5.40 inc vat)

PART NUMBERS FOR EVERY ITEM IN THIS CATALOGUE ARE IN RED AND ALWAYS

BEGIN WITH A HASH SYMBOL

#PARTNO


7" HALF BOWL BLACK RIM HEADLAMP UNIT ‘E11’ marked Wipac Quadoptic lamp without sidelight. Moulded ABS half bowl nest for maximum mounting clearance. Powder coated black steel rim with black screws. 12 Volt 60/55 Watt main and dip bulb and rubber gasket included. Overall diameter 198mm. Rear projection 70mm. Front projection 53mm. Weight 688gms.#WP1HBB £40 each (£48 inc vat)

7" HALF BOWL HEADLAMP NESTMoulded ABS half bowl nest for maximum mounting clearance. Chromed steel rim. Overall diameter 198mm. Front to back 52mm.Weight 160gms. Mounting screws included.#HALFBOWL7 £14 each (£16.80 inc vat)

CBSWIPERMOTOR PLUG

#INDSW10WIPER

CONNECTOR

-12v

+12v IGNITION

LIVE

WING PIPING Flexible black PVC. Use in the traditional way between bolt-on wings or windscreen frame and body to make a neat, sealed joint. Or, as a finishing trim around the edges of aluminium panels. 5.5mm Dia. Hollow Bead. 38mm long tail x 1.3mm thick. #TRMPI4 £2.50 mtr (£3 inc vat)

10

38

5.5

38

8.7

38

8.7mm Dia. Hollow Bead. 38mm long tail x 1.9mm thick. #TRMPI5 £3 mtr (£3.60 inc vat)

10mm Dia. Hollow Bead. 38mm long tail x 1.9mm thick. #TRMPI6 £3 mtr (£3.60 inc vat)

PART NUMBERS FOR EVERY ITEM IN THIS CATALOGUE ARE IN RED AND ALWAYS

BEGIN WITH A HASH SYMBOL

#PARTNO


RUBBER GEAR GAITER This item was originally designed for 1970s Triumph Stag (Part number 715382) but could be suitable for other applications. Moulded rubber 1.8mm thick x 50mm high with 12.5mm hole for the gear lever. Make your own retaining ring for the 145mm diameter x 12mm wide mounting flange. Maximum lateral lever movement at the gaiter hole approximately 25mm. Weight 60gms.#GRGTR2 £13 (£15.60 inc vat)

PAIR OF CHROME ENAMEL UNION JACK BADGES Metal. Size: 38mm x 21mm x 2.4mm thick (including 3M self-adhesive backing). Weight 10gms each. RED WHITE & BLUE #UJ2 £5 for 2 (£6 inc vat)

GLOSS BLACK & CHROME #UJ2BCH £5 for 2 (£6 inc vat)

73mm AIR VENT Black ABS rotating air vent with two snap-closing vanes. Clips into a 63mm hole in a panel up to 2.5mm thick.Front projection 8mm closed, 20mm fully open. Rear projection 6mm closed, 16mm fully open. Weight 20g.#VENT22 £7.50 (£9 inc vat)

CIRCULAR ROOFTOP VENTILATION PLENUM WITH FOUR VENTS Here’s a 280mm diameter air distribution plenum for the ceiling of vans or PSVs. It is fitted with four 73mm diameter rotating, directionable vents. Four 4mm mounting holes @ 260mm centres. 8mm rear projection when vents are fully open. Requires 210mm diameter hole behind for clearance if vents are fully open. Weight 220gms.#CPLEN280 £25 (£30 inc vat)

PLEASE HELP US PROCESS YOUR ORDER MORE

EFFICIENTLY BY MAKING A LIST OF

PART NUMBERS BEFORE YOUR CALL

OR VISIT

CBS BUILDERS TIPIf you’re trying to set up your front-to-back brake bias or check if your

new pads and discs are working properly, test your brakes on a gravel drive with your windows

open. Apply gentle pedal pressure at just a few miles an hour and you’ll hear clearly when the wheels lock up and you’ll even hear which one

locks up first. If it’s not your drive don’t forget to take a broom and sweep it all back.


BLACK MOULDED ABS CLIP-IN REGISTRATION PLATE HOLDERThis clever holder is designed for easy installation and changing of your registration plate. Jut unclip and open the two hinged sections on the front, drop in the plate and snap it back together. Multi fixing options. Size 532mm x 129mm x 14mm. NOTE: Flat surface mounting. Weight 200 gms.#NPSBK2 £4.50 (£5.40 inc vat)

RALLY WINDOW NETThese 57cm x 45cm window nets are essential for drivers in closed cockpits with open windows. They offer protection from debris coming in through the window and protection for the driver in the event of a collision. Weight 250gms.Available in seven colours.#WNET £25 (£30 inc vat)

SPARE WHEEL TIE DOWNKeep your spare wheel secure either inside or outsice the car. Three mounting brackets with 12mm holes. One, 1.3 mtr strap with brackets and one, adjustable 1.1mtr ratchet strap. Suitable for all wheel sizes. Strap width 25mm. Available in three colours. #WTD £16 (£19.20 inc vat)

HELMET HAMMOCKStash up to two helmets between races in this universal fil, tanglefree, black nylon mesh Helmet Hammock. Size 90cm x 50cmIt attaches to the roll cage with four 670mm long adjustable straps. Weight 250gms.#HELMHB £30 (£36 inc vat)

INTERIOR DOOR HANDLE STRAPThese lightweight, easy to fit straps are ideal for race, rally or trackday cars where the interior door cards have been modified or removed. Just bolt the strap to the door and pull it to shut. Bolt hole 12mm. 210mm length. Weight 48gms. Available in seven colours. #DHS £6 (£7.20 inc vat)

car builder solutions · without sidelight. moulded abs half bowl nest for maximum mounting...

Documents