DP70N

3060 2570 4277 200 6°/12° 70003360 2720 4577 200 6°/12° 70003560 2820 4777 200 6°/12° 70003760 2920 4977 200 6°/12° 70004060 3070 5277 200 6°/12° 70004560 3320 5777 200 6°/12° 70005060 3670 6277 200 6°/12° 70005560 3920 6777 200 6°/6° 67006060 4170 7277 200 6°/6° 64004060 2470 5277 1253 6°/6° 62004300 2570 5577 1353 6°/6° 62004570 2640 5787 1423 6°/6° 62004760 2720 5977 1503 6°/6° 62005060 2820 6277 1603 6°/6° 62005560 3070 6777 1853 6°/6° 60006070 3240 7287 2023 6°/6° 5700

DP70N

7000

6500

6000

5500

5000

4500

4000

600 700 800 900 1000 1100

Simplex

Mast Type

Triplex

h3

mm

h1

mm

h4

mm

h2/h5

mm

Tilt angle

(fwd./back)

Mast Performance and Capacityh1 Height with mast loweredh2 Standard free lifth3 Lift heighth4 Height with mast raisedh5 Full free liftQ Lifting capacity, rated loadc Load centre (distance)

NOTE: Performance specifications may vary depending on standard manufacturing tolerances, vehicle condition, types of tyres, floor or surface conditions, applications, or operating environment. Trucks may be shown with non-standard options. Specific performance requirements and locally available configurations should be discussed with your Cat lift trucks Dealer. Cat Lift Trucks follows a policy of continual product improvement. For this reason, some materials, options and specifications could change without notice.

info@catlifttruck.comwww.catlifttruck.comCESC1572(11/14)ok©2014, MCFE. All rights reserved.CAT, CATERPILLAR their respective logos, ‘Caterpillar Yellow’ and the ‘Power Edge’ trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.Printed in The Netherlands

Cat® Lift Trucks.Your partner in materials handling.

DP70N Preliminary specifi cations

Engine powered lift trucks7.0 tonnes

Q @ c = 600mm

kg

Capacities at various load centersSimplex - h3 = 3300mmCapacity (kg)

Load Center (mm)

1.1 Cat Lift Trucks1.2 DP70N1.31.41.5 70001.6 6001.8 5851.9 2300

2.1 94202.2 14800/16202.3 4190/5230

3.1 L3.2 8.25X15-12PR3.3 8.25X15-12PR3.5 4X / 23.6 16503.7 1650

4.1 6/124.2 30604.3 2004.4 33004.5 42774.7 26104.8 15924.12 4854.19 48004.20 35804.21 21704.22 60/150/12204.23 -4.24 16004.31 1704.32 2634.33a 50954.34a 52954.35 33104.36 1260

5.1 22.5 / 26.55.2 0.47 / 0.495.3 0.50 / 0.505.5 53000 / 272005.7 35 / 275.10

7.1 Perkins 854E7.2 687.3 23007.4 4 / 34007.5 -

8.18.2 1918.3 -8.4 83.48.5 Pin

α

70

Ast

a/2a/2

l6

b12

b13

b3 b10 b1b2

b11

e

x

Wa

CharacteristicsManufacturer (abbreviation)Manufacturer’s model designationPower source: (battery, diesel, LP gas, petrol)Operator type: pedestrian, (operator)-standing, -seatedLoad capacityLoad center distanceLoad distance, axle to fork faceWheelbaseWeightTruck weight, without load / including battery (simplex mast, lowest lift height)Axle loading with maximum load, front/rear (simplex mast, lowest lift height)Axle loading without load, front/rear (simplex mast, lowest lift height)Wheels, Drive TrainTyres: V=solid, L=pneumatic, SE=solid pneumatic - front/rearTyre dimensions, frontTyre dimensions, rearNumber of wheels, front/rear (x=driven)Track width (center of tyres), frontTrack width (center of tyres), rearDimensionsMast tilt, forwards/backwardsHeight with mast lowered (see tables)Free lift (see tables)Lift height (see tables)Overall height with mast raisedHeight to top of overhead guardSeat heightTow coupling heightOverall lengthLength to fork face (includes fork thickness)Overall widthFork dimensions (thickness, width, length)Fork carriage to DIN 15 173 A/B/noFork carriage widthGround clearance under mast, with loadGround clearance at center of wheelbase, with load (forks lowered)Working aisle width with 1000 x1200 mm pallets, crosswiseWorking aisle width with 800 x1200 mm pallets, lengthwiseTurning circle radiusMinimum distance between centers of rotationPerformanceTravel speed, with/without loadLifting speed, with/without loadLowering speed, with/without loadRated drawbar pull, with/without loadGradeability, with/without loadService brakes (mechanical/hydraulic/electric/pneumatic)IC EngineManufacturer / TypeRated output B to ISO 1585Rated speed to DIN 70 020Number of cylinders / cubic capacityFuel consumption according to VDI 60 cycleMiscellaneousType of drive controlMaximum operating pressure for attachmentsOil flow for attachmentsNoise level, mean value at operator’s earTowing coupling design / DIN type, ref.

Q (kg)c (mm)x (mm)y (mm) kg kg kg b10 (mm)b11 (mm) α/β °h1 (mm)h2 (mm)h3 (mm)h4 (mm)h6 (mm)h7 (mm)h10 (mm)l1 (mm)l2 (mm)b1/b2 (mm)s, e, l (mm)

b3 (mm)m1 (mm)m2 (mm)Ast (mm)Ast (mm)Wa (mm)b13 (mm) km/h m/s m/s N %

kW rpm /cm3

l/h / kg/h

barl/min

dB(A)

Hydraulic

Ast = Wa + x + l6 + aAst = Working aisle width with loada = Safety clearance (200 mm)l6 = Pallet length (800 or 1000 mm)b12 = Pallet width (1200 mm)

Lower Cost of Ownership• Advanced Perkins 854E 4-cylinder diesel engine delivers powerful performance with 18%

greater fuel effi ciency than previous units and meets EURO Stage IIIB emissions standard.• Low-maintenance Diesel Particulate Filter (DPF) technology with Passive Regeneration

(PR) avoids the need for downtime by burning off soot while truck is operating.• Engine Protection System (EPS) monitors oil pressure, coolant temperature and

transmission temperature, giving warnings and limiting power output, travel speed and hydraulic speed if abnormalities are detected.

• Robust steel frame designed using Finite Element Analysis gives durable structure with low centre of gravity, resulting in higher residual capacity.

• Fully fl oating drive axle adds extra durability and capacity compared to semi- or non-fl oating alternatives.

• Steer axle construction as a single solid unit maximises strength and rigidity.• Dependable engine and strong resistance of all truck components to damage and wear

helps minimise repair and service bills.• Easy and quick access to all areas for routine checks and maintenance keeps truck in

sound working condition, saves time and reduces expense.

Unmatched Productivity • Latest diesel engine design increases power to new levels.• Powershift transmission offers two forward and two reverse gears to tackle every task

effectively.• Fast-response compact turbocharger further enhances driver experience and output.• Design of frame and counterweight optimises weight positioning and residual capacity for

strong lifting.

Safety and Ergonomics• Noise and vibration limitation features include rubber-mounted key components, fully

insulated steel engine hood and specially designed transmission gears.• Fully hydrostatic assisted steering via small-diameter steering wheel ensures accurate

and rapid response with little effort.• Counterweight design allows small turning circle and clear view to the rear for precise

manoeuvring.• Mast with narrow channels and small-diameter lift cylinders increases forward vision and

uses six load rollers with side rollers to achieve high load stability.• Choice of up-to-date, ergonomic fi ngertip or lever controls is available for precise, low-

effort operation of hydraulic functions.• Comprehensively equipped instrument panel offers valuable on-the-go information and

warnings to aid operator awareness and control.• Presence Detection System (PDS) gives audible warning if seat belt is not fastened and

prevents all travel and hydraulic movement if operator is not correctly seated.• Vacuum-boosted hydraulic brakes increase braking effi ciency and safety.• Tiltable steering column, adjustable full-suspension seat and generous leg room allow

each user to fi nd the perfect driving position.• Conveniently placed grab bars and steps ease access to operator compartment.

Options• Engine Shutdown System (ESS) stopping engine in the event of: o Transmission temperature >110 ºC o Coolant temperature >107 ºC o Engine oil pressure <24 kPa• Range of cabin options topped by fully enclosed version with air conditioning• Wide range of sideshifters and fork positioners

DieselSeated

* Fuel consumption data available on request

Powershift 2/1