catalog bucket elevator and bucket fmc

Upload: percy-torres

Post on 01-Jun-2018

293 views

Category:

Documents


3 download

TRANSCRIPT

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    1/33

    Bucket Elevators & Buckets

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    2/33

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    3/33

    Table of Contents

     Bucket Elevators

    Link-Belt™ Bucket Elevators 5

    Standardization - the Key to Economical Design 6

    Selection Procedure for Standard Bucket Elevators, Types 1 and 7 7

    Typical Bulk Materials Handled by Bucket Elevators 8

    Link-Belt™ Bucket Elevators, Type 1 9

    Selection / Specifications Type 1 - Chain 10

    Selection / Specifications Type 1 - Belt 12

    Dimensions Type 1 Chain or Belt 14Link-Belt Bucket Elevators, Type 7 15

    Selection / Specifications Type 7 - Chain 16

    Dimensions Type 7 Chain 18

    Service Platforms 19

    Standard Components 20

    Other Bucket Elevator Models Available 21

     Elevator Buckets

    Link-Belt Elevator Buckets 22

    Elevator Bucket Types 22

    Elevator Bolts 26

    Bucket Punching for Chains 27

    Centrifugal Discharge Elevator Buckets on K Attachments 27

    Continuous Elevator Buckets on K Attachments 29

    Super Capacity Continuous Elevator Buckets on G Attachments 30

    Type AA Centrifugal Discharge Elevator Buckets on G Attachments 30Types AA and SC Centrifugal Discharge Elevator Buckets on

    A and B Wing Attachments 31

    Types AA, AA-RB and SC Centrifugal Discharge Elevator Buckets 32

    Types HF, HFO, MF and LF Continuous Elevator Buckets 32

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    4/33

    For over 100 years FMC Technologies and itspredecessor Link-Belt ®  have designed and builtconveyors and components which have set thestandard of excellence in the bulk material handlingindustry.

    FMC Technologies pioneered the development of beltconveyors, screw conveyors and feeders, bucketelevators and related conveyor components.

    While your requirements are special to you, ourengineers have faced similar situations and areintimately familiar with the challenges of handling bulkmaterials.

    Our design engineering and production experience arethe differences which set FMC Technologies conveyorequipment apart in reliability and dependability. We want

    to be our customers’ most valued supplier. Put us towork for you.

    FMC TECHNOLOGIES MATERIALHANDLING SOLUTIONS DIVISION

    FMC Technologies Material Handling Solutions Divisionin Tupelo, Mississippi, is one of the most modernconveyor equipment plants in the industry.

    The 330,000 square foot plant and office complex housesour sophisticated computer-aided (CAD) design groupadjacent to this very modern manufacturing facility.

    Administration, sales, engineering and manufacturing

    interface daily in this excellent operating environment.The result is product quality and efficiency that resultin both performance and price advantages for you.

    ABOUT OUR PRODUCTS

    Belt conveyor idlers, underground equipment,engineered screw conveyors, flighting augers andfeeders, bucket elevators, vibrating screens, feeders,bin vibrators, vibrating conveyors and packing tablesare the principal products manufactured by FMCTechnologies, Material Handling Solutions Operation inTupelo, Mississippi.

    All FMC Technologies Link-Belt conveyor productsmeet or exceed CEMA standards, and all Link-Beltequipment is produced to conform with OSHAoperational safety requirements. To that end, FMCTechnologies Material Handling Solutions Division has

    established a quality assurance program consisting ofsupport procedures, quality plans and other pertinentspecifications to ensure that Material Handling Solutionsproducts conform to specified requirements. Thisincludes the preparation of procedures and instructionswhich meet the requirements of the ISO Standard9001-2000, and effective implementation andmaintenance of these procedures and instructions.

    CUSTOMER SERVICE

    Prompt shipment, on-time delivery and after-the-saleservice are FMC Technologies trademarks. Responseto your inquiries, reliable delivery and follow throughhave built our reputation as a service oriented company.

    Our customer service specialists understand yourneeds and are experienced in meeting them.

    Link-Belt™ The Driving Forceof Industry Standards

    4

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    5/33

    Link-Belt™ Bucket Elevatorsdesigned and manufactured to provideyears of dependable and efficient service.

    Link-Belt™ Bucket Elevators,manufactured by FMCTechnologies Material HandlingSolut ions Operation, have longbeen the industry standard forany bulk mater ial elevatingapplication. Service-provenper formance under the mostdemanding operating conditionsin thousands of insta llat ions f romrural gra in elevators to largemanufacturing and processingplants ... the result of over 100years exper ience as an

    engineering pioneer andleading manufacturer.

    A Link-Belt™ designed BucketElevator is your assurance ofquality and dependabil ity, andthe standard Type 1 and Type 7FMC Bucket Elevators havemany outstanding features:• Standardization of designs thatare dependable and versati le.

    • Continuous or centr i fugaltype discharge.

    • Rig id, s trong, j ig-bui lt cas ingsin per fect a lignment andweather-tight.

    • Two-piece hood permitt ingaccess to head section inter iorwithout disturbing machinery.Spr ing clamps faci li tateremoval and replacement.

    • Inspection hatch that can beeasily l if ted to v iew terminal

    machinery.

    • Opt ional shaft mounted speedreducer drive . .. compact andeasy to insta ll .

    • Large, latch-type doors locatedon front, back and sides of bootsection to facil i tate inspect ion,service and cleanout.

    • The head shaft is mounted inant if rict ion bal l or rol ler bearingpillow blocks.

    • Superior components . . .

    chains, sprockets, pulleys,belts, buckets, bearings,takeups and drives.

    Typical bulk handlingapplications include:Del ivery o f dry c itrus pel le ts trai lroad hopper cars.

    Elevating soda ash, fer ti lizer ol imestone to silo storage.

    Deposit ing food products intoweigh hoppers.

    L ift ing coa l f rom track hopperstorage silos.

    Elevate aggregate mater ials fready-mix concrete plants.

    Link-Belt™ Bucket Elevatorf ro m F MC Te ch no lo gi es . . .indu stry's complete line . .handling hundreds of dif fek inds of mater ia l:Metallic and Non-Metallic oresBauxite, Coal

    Rock products . . . Sand. GravCement, Gypsum, Limestone

    Food products . . . Sugar, FlouCoffee, Salt

    Chemical Processing productsFertilizers, Phosphates,Agricultural Lime, Soda Ash

    Pulp and Paper products . . .Wood Chips

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    6/33

    For most bulk material elevating jobs…

    there's a Link-Belt Bucket Elevatorthat will handle them efficiently andeconomically. With over 100 years ofproven experience as a pioneer andleading producer of bucket elevators,FMC Technologies offers astandardized line of Link-Belt™

    elevators proven in thousands ofinstallations.

    Standardization is a standout featureof Link-Belt Bucket Elevators. Link-Belt Type 1 and Type 7 BucketElevator designs are standardized soyou benefit from the economics of

    many stocked components.Manufacturing methods arestandardized through exactingproduction and fabrication to assurecompatibility of components.Engineering and order processingprocedures have also beenstandardized so that the selectedelevator will accommodate yourneeds with a minimum of time andcorrespondence.

    Balanced design of components,manufacturing craftsmanship, and

    the quality found in all Link-Beltproducts, have all helped the Link-Belt Bucket Elevator achieveuniversal acceptance.

    Two basic designs of bucketelevators are available, and selectiondepends primarily on the material tobe handled.

    The Centrifugal Discharge designhas spaced buckets that travel at arelatively high speed. It is a mediumcapacity unit, capable of handlingmaterials with small-to-medium size

    lumps. The buckets dig the materialfrom the casing boot section anddischarge it by centrifugal force.

    Type 1- Elevators of this type meetthe service requirements of themajority of installations usingcentrifugal discharge elevators. Thehead shafts are fixed, with the footshaft takeup being internal gravitytype. Buckets are designed for useon either chain or belt.

    For most applications, chain is

    recommended, however, belting isused when handling materials thatmust not be contaminated or formaterials that are extremely abrasiveand corrosive.

    As an alternate to the standardType 1 centrifugal dischargedesign, Type 2 design isavailable. The head shaft isadjustable and the boot shaftfixed to maintain the relationshipof buckets to the inlet spout andcurved bottom plate. Type 2bucket elevators are

    recommended when handlingfood products; for materials thattend to pack or build-up, or whenhandling materials having alarge percentage of lumps.

    The Continuous Discharge Designhas buckets mounted continuouslythat travel at a much slower speed.The continuous discharge designelevator handles a variety ofmaterials from fines to large lumps.Materials that are difficult to pick inthe casing boot section or friable arenormally handled in this type

    elevator. The buckets are fed directlyfrom a loading leg or chute and areemptied by gravity at the dischargepoint.

    Type 7-This elevator is the mostfrequently used of the continuousdischarge design. The head shaftsare fixed, with foot shaft takeupsbeing internal gravity type. Bucketsare steel and spaced continuouslyon a strand of chain.

    As an alternate to the standardType 7 continuous discharge

    design, the Type 8 design isavailable. The head shaft isadjustable and the foot shaft isfixed. Type 8 elevators are usedfor the handling of fine orcrushed materials with lumpsnot exceeding

    1

     / 2 inch. With theaddition of a loading leg and acorrespondingly higher inletspout, this type elevator canalso be used for handling lumpsup to 4

    1

     / 2 ".

    The superior performance delivered

    by the Link-Belt Bucket Elevator isthe result of quality components,and each component described inthis catalog has been developed asan integral part of a carefullyengineered elevator design. FMCTechnologies maintains a largeinventory of bucket elevatorcomponents to meet yourreplacement needs.

    Let our FMC TechnologiesRegional Field Specialist helpyou with your selection of theproper Link-Belt™ Bucket Elevatorfor your exist ing or proposed bulkmaterial handling installation.

    CAUTION: Link-BeltBucket Elevatorsmust be installed, operated and

    maintainedin accordance with

    accompanyingFMC Technologies

    Service Instructions. Failure to follow

    these instructions canresult in serious

    personal injury, property damageor both.

    Service Instructionsaccompanythe

    shipment of equipment. It additional

    copiesof ServiceInstructions are

    required, they areavailable free of charge

    fromFMCTechnologies, MaterialHandling Solutions, Box1370, Tupelo,

    Mississippi38802.

    Link-Belt™ Bucket Elevator Standardization...the key to economical design.

    Link-Belt Bucket Elevators handle inorganicmaterials at chemical plant installation.6

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    7/33

    Prior to the selection of a Link-Belt™

    Bucket Elevator, all specifications ofthe application and conditions of theinstallation should be reviewed. As aguide to be used in selecting themost efficient and economical Link-Belt™ Bucket Elevator for anapplication, the following outline isoffered:

    1. Material Characteristics

    a. Abrasive, free-flowing, sluggish,temperature, fluffy, friable,degradable, etc...

    b. Weight per cubic foot at loadingpoint into the bucket elevator.

    c. Maximum and average size oflumps- percentage of lumps.

    2. Maximum discharge rate (t.p.h.)

    required of bucket elevator.

    3. Center to center dimensionsbetween head shaft and foot shaft.

    4. Operating conditionsa. Indoorsb. Outdoorsc. Corrosive atmosphere, etc...

    5. Type of service requireda. Continuousb. Intermittent

    6. Calculate the volumetric capacityrequired (cubic feet per hour)

    Maximum discharge rate(t.p.h.) x 2000 pounds

    Material weightper cubic foot

    7. Determine the proper type of

    bucket elevator required, basedupon the material being handledRefer to Table #1. If a specificmaterial is not listed withintabulations, select a materialhaving similar characteristics.

    8. With reference to volumetriccapacity and percent of lump sdetermine bucket elevator numusing the selection tabulationsprovided. These tabulations alindicate head shaft size andrequired horsepower.

    NOTE: I f the "weight per cubfoot" is isolated between givvalues, apply the next highefigure.

    Example #1:

    Material. . . . . . . . . . .bituminous coal

    Weight . . . . . . . . . . .50#/cu. ft.Capacity. . . . . . . . . . .70 t. p. h.Maximum lump size under 1 / 2 inchShaft centers . . . . . . 65 ft.Service . . . . . . . . . . .8-10 hrs. per day

    Step ADetermine volumetric capacity.70 x 2000 = 2800 cu. ft./hr.

    50

    Step BDetermine type of elevator. Table #1indicates either a Type 1 or Type 7.However, capacity is greater than a

    Type 7 will handle. Select Type 1.Step CRefer to selection tabulations andselect a #134 elevator rated 3120cu.ft./hr. for 65 ft. cntr. A 3 7 / 16"diameter head shaft and 15 hp driveis required.

    NOTE: A #134 elevator is fullycapable of handling the 1 / 2"andunder lumps.

    Example: #2:

    Material . . . . . . . . . . crushed limestoneWeight . . . . . . . . . . . 85-90#/cu. ft.

    Capacity . . . . . . . . . 75 t.p.h.Maximum lump size 3 / 4 inchShaft centers. . . . . . .50 ft.Service . . . . . . . . . . .8-10 hrs. per day

    Step ADetermine volumetric capacity.75 x 2000

    85

    NOTE: Use light weight for volumeand heavy weight for horsepower.

    Step BDetermine type of elevator. Table #1indicates a Type 7 for this material.

    Step CRefer to selection tabulations. A #781elevator is rated 2090 cu. ft./hr. using100#/cu. ft. and 50 ft. centers. A 315 / 16''diameter shaft and 15 hp drive isrequired. 3 / 4' ' lumps are within thecapabilities of this elevator. A #781elevator using Steel Bushed Chainrather than Combination Chain ispreferred, since the material beinghandled is mildly abrasive.

    Examples of Bucket Elevator Selection-

    = cubic feetper hour

    Selection procedure for standardBucket Elevators Types 1 and 7.

    = 1765 cu. ft./hr.

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    8/33

    Typical bulk materialshandled by Bucket Elevators

    Table 1

    Chain recommended for all elevators except those marked, where beltsare recommended. To avoid damage to belt, provide foot shafts with weldedsteel wing pulleys where there is a tendency for material to pack between belt and pulley.

    Weight of material loose or slightly agitated. This weight is generally less

    than that of settled or packed material, as in bins or containers. Select an elevator having twice the capacity required.

    8

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    9/33

    A centrifugal discharge bucketelevator-rugged construction withquality components-industry's leaderin the handling of free-flowing, fineand loose material with small tomedium size lumps.

    Bucket spacing and speed isimportant for centrifugal dischargebucket elevators. The Link-Belt™Type 1 Bucket Elevator can be reliedupon to elevate and dischargematerials at rated capacities.

    In selection of quality components,FMC Technologies engineers have,based upon laboratory tests, takeninto consideration the critical speedof operation that exists with bucketelevators. The critical speed ofoperation is the speed at which theactual capacity of the elevator dropsbelow the theoretical capacity, andexists when the centrifugal force atthe mass center of the material inthe bucket is equal to thegravitational force on the material. AllLink-Belt™ centrifugal type dischargebucket elevators operate below thecritical speed.

    Years of dependable, service-provenperformance with built-in qualitydesign features-your assurance ofmaximum efficiency:• Properly spaced buckets, mountedon durable, strong chain or toughwear resistant belt, to provide themost efficient operation per dollarinvested. Belt elevators with Link-Belt™ wing-type pulleys arerecommended when handling bulk

    materials with abrasivecharacteristics, moderatetemperatures or excessive moisturecontent.

    • Fixed head shaft with an internalgravity actuated takeup in the boot.Bearings on the takeup frame arehard iron, with the takeup shafthaving induction hardened journals.

    • Boot section is totally enclosed withlarge inspection doors to facilitatebearing replacement or the removalof the entire takeup frame.

    • Hood section is removable in twosections, and the use of waste packseals provide added protection forthe head shaft.•Standard drive is a shaft mountedspeed reducer with a built-inbackstop. Other drives are available.

    • The rigid, strong, jig-built casingare fabricated from steel plate foryears of rugged operation.• Continuously welded casings aralso available.

    Link-Belt™ Bucket ElevatorsType 1-Chain or Belt

    Type 1Bucket Elevator

    Elevator using chain

    Elevator using belt

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    10/33

    Bucket Elevator selection/specificationsType 1-Chain

    Shaded lines indicate standard design SIBS steel bushed chain.

    Bucket Elevator assemblies include head shaft machinery with either ball or roller bearing pillow blocks, chain, buckets, casing, Style 1 or Style 2 discharge spout, stub inlet and gravity takeup with

    hard iron bearings. (Internal gravity takeup is available with cement mill type sleeves and bearings when handling highly abrasive materials). Drives with backstops, service platforms and ladderswith safety cages can be furnished. Style AA buckets. Based upon buckets filled to 75/% of theoretical capacity. Based upon buckets filled to 100% of theoretical capacity. If exact material weight is not shown, select drive and head shaft using the next heavier

    material weight.

    0

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    11/33

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    12/33

    Bucket Elevator selection/specificationsType 1-Belt

    Bucket Elevator assemblies include head shaft machinery with either ball or roller bearing pillow blocks, chain, buckets, casing, Style 1 or Style 2 discharge spout, stub inlet and gravity takeup withhard iron bearings, (internal gravity takeup is available with cement mill type sleeves and bearings when handling highly abrasive materials). Drives with backstops, service platforms and ladders withsafety cages can be furnished.

    Style AA buckets. Based upon buckets filled to 75/% of theoretical capacity. Based upon buckets filled to 100% of theoretical capacity. If exact material weight is not shown, select drive and head shaft using the next heavier material weight.

    2

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    13/33

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    14/33

    Type 1-Chain or Belt

    For 10 and 12 gauge discharge spout. Deduct 1 / 8" for 7 gauge discharge spout.

    Minimum dimension for efficient loading. Deduct 2" for Type 1 Belt # 145, #147 and #149. Dimensions should not be used for Type 2 Elevators. Consult FMC for dimensional data.

    4

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    15/33

    High-capacity continuous dischargebucket elevator . . . with overlapping

    arrangement of buckets to handle avariety of materials from fines tolarge lumps. The Type 7 bucketelevator is the most frequently usedof the continuous discharge styles,with material loaded directly into thebucket through a loading leg, thatconfines the feed and preventsspillage into the boot.

    The continuous discharge bucketelevator travels at a much slowerspeed than its counterpart, thecentrifugal discharge bucket

    elevator. Standard operating speedis 125 fpm. When handling light orfluffy-type material, operatingspeeds of 160-175 fpm arecommon. When bulk material isabrasive, operating speeds arenormally reduced for longercomponent life.

    Years of dependable, service-proven performance with built-inquality design features, yourassurance of maximum efficiency:• Fixed head shafts.• Internal gravity operated takeups.• Continuously spaced steel buckets

    on a single strand of chain.• Boot section Is totally enclosed

    with large inspection doors tofacilitate bearing replacement ofthe removal of the entire takeupframe.

    • Hood section is removable in twosections, and the use of wastepack seals provide added protectionfor the head shaft.

    • Standard drive is a shaft mountedspeed reducer with a built-in

    backstop. Other drives areavailable.• The rigid, strong jig-built casings

    are fabricated from steel plate formany years of rugged operation.Weather tight casings are alsoavailable.

    Type 7Bucket Elevator

    Link-Belt™ Bucket ElevatorType 7-Chain

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    16/33

    Bucket Elevator selection/specificationsType 7-Chain

    Shaded lines indicate standard design SIBS steel bushed chain.

    Bucket Elevator assemblies include head shaft machinery with either ball or roller bearing pillow blocks, chain, buckets, casing, Style 1 or Style 2 discharge spout, stub inlet and gravity takeup withhard iron bearings. (Internal gravity takeup is available with cement mill type sleeves and bearings when handling highly abrasive materials). Drives with backstops, service platforms and ladders withsafety cages can be furnished.

    Style MF, medium front, continuous steel buckets.

    Based upon buckets filled to 75/% of theoretical capacity. Based upon buckets filled to 100% of theoretical capacity. If exact material weight is not shown, select drive and head shaft using the next heavier material weight.

    6

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    17/33

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    18/33

    Type 7-Chain

    For 10 and 12 gauge discharge spout. Deduct 1 / 8" for 7 gauge discharge spout.

    Minimum dimension for efficient loading. Dimensions should not be used for Type 8 Elevators. Consult FMC for dimensional data.

    8

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    19/33

    Standard service platforms withladders and safety cages areavailable for all Link-Belt BucketElevators. Platforms provide readyaccess to drives and head terminalsfor inspection and lubrication.

    Each platform is manufactured tobest accommodate the bucketelevator installation. Serviceplatforms, supported-by theelevator casing, extend aroundthree sides of the elevator.

    Safety cages are recommended forall ladders.

    In accordance with OSHArequirements, when ladders wcages exceed 30 feet in heighintermediate landing platformshall be provided for each 30 of height or fraction thereof.

    Service Platforms

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    20/33

    Link-Belt™ Type 1 and Type 7Bucket Elevator designs arestandardized so you benefit fromthe economics of many stockedcomponents.

    A balanced design of componentsand manufacturing craftsmanshipassure efficient operation of everyLink-Belt™ Bucket Elevator.

    Chains - Steel Bushed Chainrecommended for heavy-dutyservice. Combination Chain isavailable for light to medium-duty

    service.

    Elevator Belt- Maximum resistanceto the most common forms ofabuse damage.

    Pulleys - Precision assembly ofcarefully manufactured parts. Builtto rigid standards to assure longerbelt life.

    Sprockets - Available in solid, splitor segmental rim types withsmooth, wear-resisting file-hardbearing surfaces.

    nternal Gravity Takeups -Rugged steel frame, durablebearings, and hardened steelshafting assure trouble-freeoperation.

    Drives - A product of experiencewith unmatched reliability.

    Elevator Buckets - Style AA forcentrifugal discharge elevators andStyle MF for continuous dischargeelevators-A style for all types ofbulk material.

    Bearings - A wide selection tomeet all conditions encountered inbucket elevator operation.

    Contact your local FMCTechnologies Regional FieldSpecialist. He is anxious to provideadditional information about all thequality components found in everyLink-Belt™ Bucket Elevator.

    Link-Belt™ Standard Components...developed as integral parts of ruggedand dependable Bucket Elevators

    0

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    21/33

    In addition to the Type 1 and Type7 Link-Belt Bucket Elevatorsdescribed in this catalog, FMC hasavailable a range of types andstyles . . . designed to handle eventhe most difficult bulk material

    elevating requirements. Informationis available by contacting yournearest FMC Regional FieldSpecialist.

    BucketElevator Material Applications

    Type 6 Light, fluffy or fragile. Material with tendency to adhereto the buckets. Low bucket speed.

    Type 10 Friable, heavy or abrasive-fines to large lumps.Super capacity.

    Type 12 Free-flowing nonabrasive- slow speed. Gentlehandling.

    Type 13 Free-flowing nonabrasive- higher speed and capacitythan Type 12. Gentle handling.

    Type 14 Abrasive - cement, shale, bauxite, gypsum etc.…

    Type 15 Abrasive- feldspar, gravel, sand, clinker etc.…greater capacity than Type 14.

    Bucket Elevators...a range of models suitable for many requirements.

    Type 6PositiveDischarge

    Type 10ContinuousDischarge

    Type 12InternalDischarge

    Type 13InternalDischarge

    Type 14 and 1CentrifugalDischarge

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    22/33

    Link-Belt™ Elevator Buckets aredesigned in a variety of types andsizes to efficiently handle bulkmaterials in centrifugal dischargeand continuous bucket elevators.Buckets are either constructed offormed steel, cast, or molded withnylon or polyethelene. Castbuckets are available in ductileron, Promal, or ductile iron withFlint-Lip hardened digging lips.

    Ductile iron is the most commonlyused material in cast bucketsbecause of its ability to withstand

    the effects of abrasion andstresses during digging. Promal is

    a pearlitic malleable with highertensile and fatigue strength andyield point than ductile iron. Promalalso has a greater resistance toabrasive wear. Ductile iron elevatorbuckets with Flint-Lip provideincreased wear life when handlingabrasive materials. Elevatorbuckets can also be furnished inmild steel, abrasion-resistant steel,stainless steel and aluminum.

    Type AA and MF can be supplied ineither nylon or polyethelene.Centrifugal Discharge Elevator

    Buckets are used for handlinggranular, freeflowing materials

    which can be readily scooped upand discharged easily bycentrifugal action as the bucketspass over the elevator head wheel.

    When higher capacities at lowerspeeds are desired, or when thematerial being handled is friableand fragile, Continuous ElevatorBuckets are used. Material is feddirectly into the bucket and isdischarged over the elevator headwheel onto the preceding bucketwhich acts as a chute, providing aclean, gentle discharge.

    Type AA Centrufugal Discharge Elevator Buckets aremade of ductile iron or Promal for mounting on chains orbelts. They have a thick, wide reinforced lip along the frontedge and front corners for resistance to distortion when

    scooping up heavy or gritty materials. For increased wearife when handling abrasive materials, buckets can befurnished when hardened lips.

    Type AAW Centrifugal Discharge Elevator Buckets aredentical with Type AA buckets, except they are available in

    mild steel, abrasion-resistant steel or stainless steel.

    Link-Belt™ Elevator Buckets

    For Centrifugal Discharge andContinuous Bucket Elevators.

    Elevator Bucket Types

    Have dimensions certified for installation purposes.

    Boldface type indicates unpunched ductile iron buckets normally carried in stock. Bucketsmade of Promal, ductile iron with hardened lip, or ductile iron with galvanized protectivecoating can be furnished.

    Actual capacity depends on angle of repose of material handled.

    2

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    23/33

    Type AA Plastic Centrifugal Disch Elevator Bucketsare identical to type AA except are available in ''SuperTuff" nylon or polyethelene for food grade.

    Type AA-RB Centrifugal Discharge Elevator Bucketsare made of ductile iron or Promal and are identical withType AA buckets, except the back edges are thicker toprovide greater resistance to distortion. The wide digginglip and vertical reinforcing ribs on the front enable thesebuckets to withstand rough service. For increased wearlife when handling abrasive materials, buckets can befurnished with hardened lips.

    Type SC Centrifugal Discharge Elevator Buckets aremade of ductile iron for mounting on chains or belts.They are suitable for handling dry or relatively wetmaterials at greater capacities than Type AA buckets.The buckets are smooth, seamless and uniformly cast to

    resist abrasive wear, corrosion and rust.

    Link-Belt™ Elevator Buckets

    Have dimensions certified for installation purposes.

    Boldface type indicates unpunched ductile iron buckets normally carried in stock. Bucketsmade of Promal, ductile iron with hardened lip, or ductile iron with galvanized protectivecoating can be furnished.

    Actual capacity depends on angle of repose of material handled.

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    24/33

    Type AC Centrifugal Discharge Elevator Buckets aremade of ductile iron or Promal for mounting on chain.They have a thick, wide reinforced lip along the front edge

    and front corners to increase resistance to distortion. Thehigh front increases capacity, and hooded backs permitscloser bucket spacing. Air-pressure relief holes in thebottom of the buckets assure faster loading and unloadingof free-flowing materials, such as cement. For increasedwear life when handling abrasive materials, buckets canbe furnished with hardened lips.

    Type ACS Centrifugal Discharge Elevator Buckets aremade of mild steel or aluminum for mounting on chain.Their high front and the saddlebag or wraparound featureincreases capacity, while the hooded backs permit closerbucket spacing. For increased wear life when handlingabrasive materials, buckets can be furnished withhardened lips.

    Type HFO Continuous Elevator Buckets are made ofwelded steel for mounting on chains or belts. They havethe same high front as Type HF buckets, but in addition,are overlapping to prevent leakage between buckets.Bevel washers are recommended to avoid interference ofadjacent buckets. The smooth interior allows the materialto be easily and quickly discharged. Buckets are offormed and welded steel construction. The front plates

    are either intermittent or continuous welded to the backand side plates, depending on the fineness of thematerial being handled.

    Link-Belt™ Elevator Buckets

    Have dimensions certified for installation purposes.

    Actual capacity depends on angle of repose of material handled.

    24

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    25/33

    Type HF Continuous Elevator Buckets are made ofwelded steel for mounting on chains or belts. They havehigh fronts and are proportioned for high capacity. Thesmooth interior allows the material to be easily and quicklydischarged. Buckets are of formed and welded steelconstruction. The front plates are either intermittent orcontinuous welded to the back and side plates, dependingon the fineness of the material being handled.

    Super Capacity Continuous Elevator Buckets are madeof welded steel for mounting between two strands of chain.They are normally used on super-capacity type continuousbucket elevators. The smooth interior permits a quick, cleandischarge of material. The front and bottom plates areeither intermittent or continuous welded to the back andside plates, depending on the fineness of the material beinghandled.

    Type LF Continuous Elevator Buckets are made ofwelded steel for mounted on chains or belts. They havelow fronts and are designed for inclined bucket elevatorsor to handle finely pulverized or wet materials. Bucketsare of formed and welded steel construction. The frontplates are either intermittent or continuous welded to theback and side plates, depending on the fineness of thematerial being handled.

    Link-Belt™ Elevator Buckets

    Have dimensions certified for installation purposes.

    Actual capacity depends on angle of repose of material handled.

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    26/33

    ype MF Continuous Elevator Buckets are made of weldedeel for mounting on chains or belts. They have mediumonts and are used for handling a variety of materials. Themooth interior provides a quick, clean discharge of material.uckets are of formed and welded steel construction. The

    ont plates are either intermittent or continuous welded to theack and side plates, depending on the fineness of theaterial being handled.

    ype MF ''Plastic'' Continuous Elevator Buckets areentical to MF except are available in ''Super Tuff'' nylon orolyethelene for food grade applications.

    evator Bolts are made to ANSI specifications and are heldexacting tolerances. We offer our SABRE-TOOTH HEAD ® 

    carbon steel only.

    evator bolts are “Low Shoulder” design to accommodatequirements for use on today's ultra-thin belting.

    ain finish and zinc plated carbon steel in stock.

    Link-Belt™ Elevator Buckets

    STANDARD#1 Norway Carbon Steeland Stainless Steel

    RELIENCE#3, Carbon Steel

    SABRE-TOOTH ® 

    #1 Norway W/Toothed headCarbon Steel

    ve dimensions certified for installation purposes.

    Actual capacity depends on angle of repose of material handled.

    6

    Elevator Bolts

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    27/33

    Bucket Punching for Chains

    Centrifugal Discharge Elevator Buckets on K Attachments

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    28/33

    Bucket Punching for ChainsCentrifugal Discharge Elevator Buckets on K Attachments (continued)

    8

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    29/33

    CAUTION: Link-Belt™ Elevator Buckets must beinstalled, operated and maintained in accordancewith accompanying FMC Technologies ServiceInstructions. Failure to follow these instructionscan result in serious personal injury, propertydamage or both.

    Service Instructions accompany the shipment ofequipment. If additional copies of Service Instructionsare required, they are available free of charge from FTechnologies, Material Handling Solutions, Box 1370,Tupelo, MS 38801.

    Bucket Punching for Chains

    Continuous Elevator Buckets on K Attachments

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    30/33

    Bucket Punching for Chains

    Super CompacityContiuous Elevator Buckets on G Attachments

    Type AA Centrifugal Discharge Elevator Buckets on G Attachments

    ave dimensions certified for installation purposes.

    Minimum bucket size which wil accomodate attachment

    0

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    31/33

    Bucket Punching for Chains

    Types AA and SCCentrifugal Discharge Elevator Buckets onA and B Wing Attachments

    Have dimensions certified for installation purposes.

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    32/33

    Bucket Punching for Belts

    Types AA, AA-RB, and SC Centrifugal Discharge Elevator Buckets

    Types HF, HFO, MF, and LF Continuous Elevator Buckets

    32

  • 8/9/2019 Catalog Bucket Elevator and Bucket FMC

    33/33

    f h l i / i lh dli© 2008 • FMC Technologies, Inc.

    FMC Technologies, Inc.

    Material Handling Solutions

    PO Box 1370

    Tupelo, MS 38802

    Tel: 662-869-5711Fax: 662-869-7493

    Toll Free: 800-356-4898

    Email: [email protected]

    FMC Technologies, Inc.

    2# Road No. 1

    Changshu Export Processing Zone

    Changshu, Jiangsu

    China 215513Tel: 86-0512-52299002

    Fax: 86-0512-52297228

    Email: [email protected]

    FMC Technologies Chile Ltda.

    Callao 2970

    Office 704

    Las Condes, Santiago, Chile

    Tel: 56 2 234 441856 2 246 4361

    Fax: 56 2 232 0825

    Email: [email protected]

    Material Handling Solutions

    Technisys

    479 West 900 North

    North Salt Lake, UT 84054

    Tel: 801-296-9500

    Fax: 801-296-9601

    Email: [email protected]

    Link-Belt® Products

    • Belt Conveyor Idlers

    • Idler Rolls

    • Scavenger™ Belt Conveyor Cleaners

    • Screw Conveyors

    • Bucket Elevators

    • Link-Belt® Component Parts

    • Heavy-Duty Vibrating Feeders

    • Vibrating Screens

    • Grizzly Bar Screens

    • Vibrating Conveyors

    Syntron® Products

    • Heavy-Duty Vibrating Feeders

    • Vibrating Screens

    • Grizzly Bar Screens

    • Vibrating Conveyors

    • Light-Duty Vibrating Feeders

    • Vibra-Drive Units

    • Volumetric Feeder Machines

    • Screening Feeders

    • Bin Vibrators

    • Packing Tables

    • Paper Joggers

    • Syntron Component Parts