catalog plates bilz antivibrations
TRANSCRIPT
-
7/25/2019 Catalog Plates BILZ Antivibrations
1/13
VIBRATION TECHNOLOGY
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Test procedure
The insulating plates had the typical dimensions and
w ere loaded w ith the w eight as noted in the
corresponding table.
To get an experim enta l setup as realistic as possible,
the insulating p lates were positioned as three-
point -bearings underneath th e reference-w eight.
The experimental setup was activated by a 1600
Newton X-Y-Z-shaker in vertical and horizontal
direction in a frequency range from 0,5 up t o 100Hz.
Technical note:
The pro cedure described ab ove m easures thedynami cal stif fness, wh ich is much closer to realistic
circumstances than the stati c sti ffness. This is because
the stiffness of elastomer springs highly
correlates w ith the activatio n f requency. Dynamically
measured natural frequencies are normally
higher than statically measured ones.
-
7/25/2019 Catalog Plates BILZ Antivibrations
2/13
Load N / cm 2 30 60 90
daN/cm2 3 6 9
Vertical dynamical n atural frequency f ov Hz 69 54 44
Horizontal dynamical natural frequency foh Hz 28 21 19
Vertical damping rat io Dv % 16 15 14
Horizontal damping ratio Dh % 16 19 17
75
70
65
60
55
50
45
40
0 2 4 6 8 1 0 1 2
30
28
26
24
22
20
18
160 1 2 3 4 5 6 7 8 9
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
1 0 1 1 1 2
Range of application:
Very universal.Can be used for machine tools, plastic and printing machines. Extremely well suited tomachines with a tendency to " migrate"
Compound insulat ing platestype B4
Type: Wit h prof ile on both sidesLoad: 3-10 d aN/cm 2
Thickness unloaded: 15m m
DATASHEET
Load daN/ cm2
dynamicnaturalfrequencyHz
dynamicnatura
lfrequencyHz
Load daN/ cm2
Vertical dam ping coefficient Horizontal damping coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
3/13
85
80
75
70
65
60
55
0 2 4 6 8 1 0 1 2
30
28
26
24
22
20
18
16
0 2 4 6 8 1 0 1 2
Load N / cm 2 30 60 90
daN/cm2 3 6 9
Vertical dynamical n atural frequency f ov Hz 83 66 59
Horizontal dynamical natural frequency foh Hz 29 22 20
Vertical damping rat io Dv % 16 15 14
Horizontal damping ratio Dh % 16 19 17
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Range of application:
Very universal. Can be used fo r machin e too ls, plastic and print ing m achines. Extrem ely w ell suited t omachines w i th a tendency to " migrate"
Compound insulating platestype B4-1
DATASHEET
Type: Wit h prof ile on o ne sideLoad: 3-10 d aN/cm 2
Thickness unloaded: 15m m
Load daN/ cm2
dynamicnatura
lfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical dam ping coefficient Horizontal damping coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
4/13
26
24
22
20
18
16
90
85
80
75
70
1 0 1 2 1 40 2 4 6 8 1 0 1 2 1 40 2 4 6 8
Load N / cm 2 60 90 120
daN/cm2 6 9 12
Vertical dynamical n atural frequency f ov Hz 86 80 75
Horizontal dynamical natural frequency foh Hz 24 21 19
Vertical damping rat io Dv % 17 16 15
Horizontal damping ratio Dh % 16 19 17
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Compound insulating platest ype B0
Range of applicat ion:
Very high l evel constancy. Particularly for m achines w ith litt le rigidit y such as: lathes, machining centers,transfer lines etc.
Type: Wit hout any profileLoad: 5-12 d aN/cm 2
Thickness unloaded: 15m m
DATASHEET
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
5/13
75
70
65
60
55
50
45
4010 12 14 16 18 20 22 24 26 28 30 32 34 36 38
28
27
26
25
24
23
22
21
20
19
18
17
16
10 12 14 16 18 20 22 24 26 28 30 32 34 36 38
Load N / cm 2 120 240 360
daN/cm2 12 24 36
Vertical dynamical n atural frequency f ov Hz 68 59 48
Horizontal dynamical natural frequency foh Hz 26 20 18
Vertical damping rat io Dv % 11 10 9
Horizontal damping ratio Dh % 12 15 13
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Range of application:
Insulating plate w ith extremely high loadability coupled w ith maxim um level constancy. E.g. for heavy andlong bedded m achining centers, transfer lines, etc.
Compound insulating platestype B6
Type: W ithout any profileLoad: 10-40 daN/cm 2
Thickness unloaded: 15m m
DATASHEET
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
6/13
DATASHEET
50
45
40
35
30
25
0 2 4 6 8 1 0 1 2 1 4 1 6
24
22
20
18
16
14
12
10
0 2 4 6 8 1 0 1 2 1 4 1 6 1 8 2 0
Load N / cm 2 60 90 120
daN/cm2 6 9 12
Vertical dynamical n atural frequency f ov Hz 50 40 34
Horizontal dynamical natural frequency foh Hz 22 18 17
Vertical damping rat io Dv % 15 14 13
Horizontal damping ratio Dh % 15 18 16
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Range of application:
For m achines wi th high dynam ic disturban ce properties and onl y a smal l support plat e, e.g. presses,stam pin g p resses, shears, etc.
Compound insulating platestype B5
Type: Wit h prof ile on both sidesLoad: 5-16 d aN/cm 2
Thickness unloaded: 25m m
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
7/13
DATASHEET
65
60
55
50
45
40
0 2 4 6 8 1 0 1 2 1 4 1 6 1 8
22
20
18
16
14
12
10
8
0 1 2 3 4 5 6 7 8 9 1 0 11 12 13 14 15
Load N / cm 2 60 90 120
daN/cm2 6 9 12
Vertical dynamical n atural frequency f ov Hz 61 52 47
Horizontal dynamical natural frequency foh Hz 21 18 16
Vertical damping rat io Dv % 15 14 13
Horizontal damping ratio Dh % 15 18 16
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Compound insulating platestype B50
Type: Wit hout any profileLoad: 5-16 d aN/cm 2
Thickness unloaded: 25m m
Range of applicat ion:
For m achines wi th high dynam ic disturban ce properties and onl y a smal l support plat e, e.g. presses,stam pin g p resses, shears, etc.
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal damping coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
8/13
DATASHEET
60
55
50
45
40
35
30
19
18
17
16
15
14
13
12
1 2 3 4 5 6 7 1 2 3 4 5 6
Load N / cm 2 35 40 50
daN/cm2 3,5 4 5
Vertical dynamical n atural frequency f ov Hz 55 45 35
Horizontal dynamical natural frequency foh Hz 19 16 13
Vertical damping rat io Dv % 14 13 12
Horizontal damping ratio Dh % 14 14 12
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Compound insulating platestype B30
Type: Wit hout any profileLoad: 2-5 daN/cm 2
Thickness unloaded: 18m m
Range of applicat ion:
Soft kind without any profile. Specially suited for effective insulation of lighter presses, punching machines,etc. on upper flo ors.
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
9/13
15
14
13
12
11
109
8
7
6
5
50
45
40
35
30
25
20
0 1 2 3 4 5 0 1 2 3 4 5
Load N / cm 2 10 20 40
daN/cm2 1 2 4
Vertical dynamical n atural frequency f ov Hz 42 38 28
Horizontal dynamical natural frequency foh Hz 13 11 7
Vertical damping rat io Dv % 14 13 12
Horizontal damping ratio Dh % 11 9 12
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Compound insulating platestype B30 W
DATASHEET
Type: Wit h prof ile on both sidesLoad: 0,5-4 daN /cm2
Thickness unloaded: 18m m
Range of applicat ion:
Very soft kind for m ainly passive insulation. High insulation effect due t o low frequency tun ing. E.g. formeasuring and testing machin es, scales, microscopes and gri nders.
Load daN/ cm2
dynamicnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
10/13
16
15
14
13
12
11
10
9
8
7
6
5
50
45
40
35
30
25
20
0 1 2 3 4 50 1 2 3 4 5
Load N / cm 2 10 20 40
daN/cm2 1 2 4
Vertical dynamical n atural frequency f ov Hz 43 38 29
Horizontal dynamical natural frequency foh Hz 15 13 8
Vertical damping rat io Dv % 14 13 12
Horizontal damping ratio Dh % 11 9 12
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
Compound insulating platestype B30 W-1
Type: Wit h prof ile on o ne sideLoad: 0,5-4 daN /cm2
Thickness unloaded: 18m m
Range of applicat ion:
Very soft kind for m ainly passive insulation. High insulation effect due t o low frequency tun ing. E.g. formeasuring and testing machin es, scales, microscopes and gri nders.
DATASHEET
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
11/13
10
9
8
7
6
5
70
60
55
50
45
40
35
30
25
200 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
Load N / cm 2 35 50 65
daN/cm2 3,5 5 6,5
Vertical dynamical n atural frequency f ov Hz 58 41 34
Horizontal dynamical natural frequency foh Hz 8 7 7,5
Vertical damping rat io Dv % 16 15 14
Horizontal damping ratio Dh % 11 14 12
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
DATASHEET
Compound insulating platestype B32
Type: Wit hout any profileLoad: 2-8 daN/cm 2
Thickness unloaded: 25m m
Range of applicat ion:
Soft kind similar to B30, but with higher load capability. For medium to big presses, punching presses etc.Very high insulation.
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
12/13
13
12
11
10
9
8
7
6
5
40
35
30
25
20
0 1 2 3 4 50 1 2 3 4 5
Load N / cm 2 10 20 40
daN/cm2 1 2 4
Vertical dynamical n atural frequency f ov Hz 31 27 22
Horizontal dynamical natural frequency foh Hz 11 9 6
Vertical damping rat io Dv % 13 12 11
Horizontal damping ratio Dh % 8 11 9
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
DATASHEET
Compound insulating platestype B13W
Type: Wit h prof ile on both sidesLoad: 0,5-4 daN /cm2
Thickness unloaded: 13m m
Range of application:
Special kin d for h ighest insulat ion valu es, can be stacked up to 5 ti mes. Tunin g up t o appro x. 8 Hz.Recommended as so-called plate-set for foundation insulations.
Load daN/ cm2
dynamicnaturalfrequencyHz
dynamicnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)
mass m (kg)
We reserve the rigth to make technical changes!
-
7/25/2019 Catalog Plates BILZ Antivibrations
13/13
8
7
6
5
4
3
2
1
00 1 2 3 4
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
0 1 2 3 4
Type B13W(2)/ B8 B13W(3)/ B8 B13W(4)/ B8 B13W(5)/ B8 B13W(6)/ B8
Load N / cm 2 20 20 20 20 20
daN/cm2 2 2 2 2 2
Vertical dynamical n atural frequency f ov Hz 14,25 11,00 9,00 7,75 6,75
Horizontal dynamical natural frequency foh Hz 5,98 4,75 3,75 3,25 3,00
Vertical damping rat io Dv % 10 10 10 10 10
Horizontal damping ratio Dh % 10 10 10 10 10
Bi lz V ibrat ion Technology AG Bbl ingerSt r. 25 D-71229 Leonberg Fon 0 71 52 / 30 91- 0 Fax 0 7152 / 30 91-10 info@bi lz .ag ww w.bi lz.ag
B13-W(2)/B8
B13-W(3)/B8
B13-W(4)/B8
B13-W(5)/B8
B13-W(6)/B8
B13-W(2)/B8
B13-W(3)/B8
B13-W(4)/B8
B13-W(5)/B8
B13-W(6)/B8
DATASHEET
Compound insulat ing plat e-settype B13W / B8
Type: Wit h prof ile on both sides
Load: 0,5-3,5 d aN/cm 2
Range of application:
Used f or fou ndation insulation in corresponding layers.
Load daN/ cm2
dynam
icnaturalfrequencyHz
dynam
icnatura
lfrequencyHz
Load daN/ cm2
Vertical damping coefficient Horizontal dampin g coefficient
Formular to calculate the dynamical stiffness:
w i t h
dynamical stiffness C (N/m)
natural frequency f (Hz)mass m (kg)
We reserve the rigth to make technical changes!