catalogue index content page - cla-val pacific catalogue.pdf · piping extended by others ......
TRANSCRIPT
R
CONTENT PAGECATALOGUE INDEX
OPERATION -SERIES RGX 1 - 2
RECOMMENDED INSTALLATION ARRANGEMENTS -SERIES RGX 3
AVAILABLE DISCHARGE CONNECTIONS -SERIES RGX 4
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGX 5DN50 (2") - DN100 (4") - Flanged
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGX 6DN50 (2") - DN100 (4") - Flanged (Expanded Body)
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGX 7DN150 (6") & DN200 (8") - Flanged
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGX 8DN150 (6") & DN200 (8") - Flanged (Expanded Body)
GENERAL SPECIFICATIONS - SERIES RGX 9DN50 (2") - DN200 (8") - Flanged
GENERAL SPECIFICATIONS - SERIES RGX 10DN50 (2") - DN200 (8") - Flanged (Expanded Body)
SELECTION & POSITIONING - SERIES RGX 11 - 12
SURGE & WATERHAMMER PROTECTION SERIES RGX 13 - 14
SMALL ORIFICE DISCHARGE PERFORMANCE 15
WHY VENT-O-MAT SERIES RGX? 16
PURCHASE SPECIFICATIONS - SERIES RGX 17
ORDERING GUIDE & TEST SPECIFICATIONS - SERIES RGX 18
OPERATION - SERIES RGXb 19 - 20
RECOMMENDED INSTALLATION ARRANGEMENTS - SERIES RGXb 21
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXb 22DN50 (2") - DN100 (4") - Flanged
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXb 23DN50 (2") - DN100 (4") - Flanged (Expanded Body)
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXb 24DN150 (6") & DN200 (8") - Flanged
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXb 25DN150 (6") & DN200 (8") - Flanged (Expanded Body)
GENERAL SPECIFICATIONS - SERIES RGXb 26DN50 (2") - DN200 (8") - Flanged
GENERAL SPECIFICATIONS - SERIES RGXb 27DN50 (2") - DN200 (8") - Flanged (Expanded Body)
PURCHASE SPECIFICATIONS - SERIES RGXb 28
OPERATION - SERIES RGXv 29 - 30
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXv 31DN50 (2") - DN100 (4") - Flanged
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXv 32DN50 (2") - DN100 (4") - Flanged (Expanded Body)
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXv 33DN150 (6") & DN200 (8") - Flanged
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONS - SERIES RGXv 34DN150 (6") & DN200 (8") - Flanged (Expanded Body)
GENERAL SPECIFICATIONS - SERIES RGXv 35DN50 (2 - DN200 (8 - Flanged
GENERAL SPECIFICATIONS - SERIES RGXv 36DN50 (2 - DN200 (8 - Flanged (Expanded Body)
PURCHASE SPECIFICATIONS - SERIES RGXv 37
ORDERING GUIDE - SERIES RGXb & RGXv 38
") ")
") ")
R
Series RGXOPERATION
PRESSURIZED AIR/GAS RELEASEPIPELINE OPERATING
VACUUM RELIEF (AIR INTAKE)PIPELINE DRAINING
PIPELINE FILLING(SUB CRITICAL SEWAGE/ EFFLUENT
APPROACH VELOCITY)
PIPELINE FILLING(EXCESSIVE SEWAGE/ EFFLUENT
APPROACH VELOCITY)
PIPELINE FULLY CHARGED
1 2 3
54
Normal Operating Level(Small Orifice ControlFloat Buoyancy Level)
10 bar (145 psi)Working Pressure
Maximum Surge Level"Anti - Surge" Orifice
"Anti - Surge" Float
information subject to change without prior noticepage: 1
R
Series RGX
OPERATION
A) VENTING OF A FILLING PIPELINE:
B) SURGE ALLEVIATION - PIPELINE PRESSURIZED:
Attention is drawn to Pre Notes (A) and (B) above.
NO FLUSHING CONNECTION ARE NECESSARY.
NO FLUSHING CONNECTIONS ARE NECESSARY.
NO FLUSHING CONNECTIONS ARE NECESSARY.
*NOTE:
The operation of a conventional sewage air release valve is such that fast approaching sewage/effluent is almost instantaneously haltedby the valve's closure. Consequently a transient pressure rise or shock of potentially damaging proportions can be generated in a pipelinesystem, even at normal filling rates.
In addition to venting through the Large Orifice when sewage/ effluent approach velocities are sub critical, the Vent -O- Mat seriesRGX sewage air release valves feature an automatic "Anti - Surge" Orifice device that serves to decelerate sewage/ effluentapproaching at excessive speed, thereby limiting pressure rise in the pipeline.
In instances where a pipeline experiences liquid column separation due to pump stoppage, high shock pressures can be generated whenthe separated column rejoins.
The Vent -O- Mat series RGX takes in air through the unobstructed large orifice when column separation occurs, but controls thedischarge of air/gas through the "Anti-Surge" Orifice as the separated column commences to rejoin. The rejoining impact velocity isthereby sufficiently reduced to prevent an unacceptably high surge pressure in the system. In the same way the series RGX valveprevents high surge pressures resulting from liquid oscillation in a pipeline.
Air/gas flows through the annular area around the control float assembly and to atmosphere through the large orifice.
In reaction to an increase in air/gas flow, the "Anti - Surge" float closes the large orifice and air/gas is forced through the "Anti - Surge"Orifice resulting in a deceleration of the approaching liquid due to the resistance of rising air/gas pressure in the valve.
Sewage/effluent has entered the the valve chamber and buoyed the floats to close both the large and the small orifice. The design'scompression/ volume relationship prevents the media from ever exceeding the maximum surge level indicated in diagram 3. Theresultant sewage/ effluent free area protects against the fouling of the orifice seals by solids or high viscous substances - for this reason
The volume of disentrained air/gas increases in the valve and displaces the sewage/effluent to the lower, normal operating level (smallorifice control float buoyancy level). Any additional lowering of the sewage/effluent level, as would occur when more air/gas enters thevalve, will result in the control float dropping away from the small orifice through which pressurized air/gas is then being discharged toatmosphere.
The control float will close the small orifice when sufficient air/gas has been released to restore the sewage effluent to the normaloperating level.
The considerable sewage/effluent free area obviates the possibility of leaks that could otherwise be caused by solids entering thesealing areas - for this reason
When the internal pipeline pressure reduces to atmosphere the "Anti - Surge " mechanism and control float assembly drops, opens thelarge orifice and allows the pipeline to take in air to displace the draining media so as to prevent undesirable low negative pressure*.Thehollow, smooth side float design discourages adherence of solids and viscous substances which, therefore, tend to withdraw from thevalve into the pipeline when draining occurs - for this reason
Negative pressure values are dependant on valve size selection.
1. PIPELINEFILLING (SUBCRITICALSEWAGE/EFFLUENTAPPROACHVELOCITY)
2. PIPELINEFILLING(EXCESSIVESEWAGE/EFFLUENTAPPROACHVELOCITY)
3. PIPELINEFULLYCHARGED
4. PRESSURIZEDAIR/GASRELEASE-PIPELINEOPERATING
5. VACUUMRELIEF(AIRINTAKE)-PIPELINEDRAINING
PRE NOTES:
information subject to change without prior noticepage: 2
R
RECOMMENDED INSTALLATION ARRANGEMENTS
Series RGX
information subject to change without prior noticepage: 3
AIR VENT (AIR IN)DIAMETER EQUAL
OR GREATER THANNB OF AIR VALVE
AIR VENT (AIR OUT)DIAMETER EQUAL
OR GREATER THANNB OF AIR VALVE
AIR VALVEPIPING EXTENDED
BY OTHERS
AIR VALVEISOLATOR
BY OTHERS
MANHOLE
STONE
AIR/ GAS
SEWAGE/ EFFLUENT
LOWER SUMP TO ALLOW DRAINAGE BY SUMP PUMP
VALVE CHAMBER
AIR/ GAS ACCUMULATOR
TYPICAL VALVE CHAMBER
d = 0.5 DMIN.h = D MIN.
D
TYPE 1 TYPE 2
R
AVAILABLE DISCHARGE CONNECTIONS50 ( 200 (2") TO 8")
250 (10") & 300 (12") VALVES AVAILABLE ON REQUEST
Series RGX
information subject to change without prior notice
page: 4
Standard DischargeConnection. ScreenMesh On Outlet.DN50 (2"), DN80 (3"), DN100 (4"),DN150 (6") & DN200 (8")
Swivel Flange OutletConnection.*
Flanged Trophy InletConnection forDN250 (10”) & DN300 (12”)Valves Only
*NOTE:Discharge Connections Are Equal To Valve Pressure Rating
Screwed BSP/NPTInlet Connection.DN50 (2") Valves Only.
STANDARDS
StuddedInlet Connection.DN80 (3"), DN100 (4 ,DN150 (6 & DN200 (8Valves Only.
")") ")
SPECIAL ORDERS
R
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONTHREADED 50 (2") & ")STUDDED INLET - 80 (3") TO 100 (4
Type: End Connection:
Nominal Sizes: Model No: Pressure Ratings:
Series RGX - Double Orifice (Small & Large Orifice) Flange with Threaded BSP/NPT Male - 50 (2 valves.with "Anti-Surge" Mechanism.
DN50 (2") RGX 1011/1021 PN10 (145 psi)DN80 (3
")Flange with Screwed Studs - 80 (3") & 100 (4") valves.
") RGX 1001/1031 PN10 (145 psi)DN100 (4")
Series RGX
information subject to change without prior noticepage: 5
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Upper FloatHigh Density Polyethylene
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
Connecting BracketStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
O - Ring SeatEPDM Rubber
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
StudsStainless Steel AISI 304L
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
Note: 50 (2
Valves are available in AISI 316L on request.
") Threaded BSP/NPT Male Inlet
O - Ring SeatEPDM Rubber
R
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Upper FloatHigh Density Polyethylene
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
Connecting BracketStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
O - Ring SeatEPDM Rubber
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
StudsStainless Steel AISI 304L
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONTHREADED 50 (2 STUDDED INLET - 80 (3 TO 100 (4") EXPANDED BODY") & ")
Series RGX
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGX - Double Orifice (Small & Large Orifice) Flange with Threaded BSP/NPT Male 50 (2 valves.with "Anti-Surge" Mechanism.
DN50 (2
DN100 (4")
")Flange with Screwed Studs 80 (3") & 100 (4") valves.
") RGX 1611/1621 PN16 (232 psi)Dn80 (3”) RGX 1601/1631 PN16 (232 psi)
page: 6
information subject to change without prior notice
O - Ring SeatEPDM Rubber
Note: 50 (2
Valves are available in AISI 316L on request.
") Threaded BSP/NPT Male Inlet
R
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONSTUDDED INLET - 6") & 8150 ( 200 ( ")
Type: End Connection:
Nominal Size: Model No: Pressure Rating:
Series RGX - Double Orifice (Small & Large Orifice) Flange with Screwed Studs - 150 (6 & 200 (8 valves.with "Anti-Surge" Mechanism.
DN150 (6") RGX 1001/1031 PN10 (145 psi)DN200 (8
") ")
")
Series RGX
information subject to change without prior noticepage: 7
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Upper FloatHigh Density Polyethylene
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
Float ScrewStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
StudsStainless Steel AISI 304L
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
Note: Valves are available in AISI 316L on request.
O - Ring SeatEPDM Rubber
O - Ring SeatEPDM Rubber
R
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Upper FloatHigh Density Polyethylene
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
Float ScrewStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
O - Ring SeatEPDM Rubber
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
StudsStainless Steel AISI 304L
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONSTUDDED INLET - 6") & 200 (8") EXPANDED BODY150 (
Series RGX
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGX - Double Orifice (Small & Large Orifice) Flange with Screwed Studs - 150 (6 & 200 (8 valves.with "Anti-Surge" Mechanism.
150 (6") RGX 1601/1631 PN16 (232 psi)
200 (8")
") ")
page: 8
information subject to change without prior notice
Note: Valves are available in AISI 316L on request.
O - Ring SeatEPDM Rubber
R
Series RGX
Type:
End Connection:
Nominal Sizes:
Model No's: Pressure Ratings bar (psi):
Operating Pressure Range - bar (psi):
Function:
Valve Selection:-
Materials of Construction:-
Installation:-
Standard Factory Tests:
Double Orifice (Small & Large Orifice) with Anti Surge Orificemechanism.
Flange with DN50 (2 Male BSP/NPT Threaded and ScrewedStuds for Alignment to BS4504, SABS 1123 and ANSI B16.5Class 150 for DN80 (3 to DN200 (8
DN50 (2”), DN80 (3"), DN100 (4"), DN150 (6") & DN200 (8")
RGX 1011/1021 PN10 (145 psi)
Min Max.PN10 (145 psi) 0.5 (7.2) 10 (145)
i) High volume air/gas discharge - pipeline filling.ii) High volume air intake - pipeline drainingiii) Pressurized air/gas discharge - pipeline filled.iv) Surge dampening - high velocity air/gas discharge,
liquid column separation & liquid oscillation.
see pages 11 & 12
see pages 5 & 7
see page 3
i) Hydrostatic test -1.5 x max. rated working pressureii) Low head leak test - 0.5 bar (7.2 psi)iii) Small orifice function test at max. rated working pressure
(minimum 1 valve in 10).
")
") ").
RGX 1001/1031 PN10 (145 psi)
GENERAL SPECIFICATIONSTHREADED 50 (2 STUDDED INLET - 80 (3") TO 200 (8") & ")
information subject to change without prior noticepage: 9
A
D EA
Note: DN50 (2") valves have DN50 (2") BSP/NPT male inlet connections as standard.
OVERALL DIMENSIONS & WEIGHTS
C
B
F
80 3 080 RGX 1001/1031 285 780 55 200 80 3 36.511 ¼ 30 / 2 / 7 / 80.5710
18
78 N/A
100 4 100 RGX 285 780 55 220 100 4 361001/1031 N/A11 ¼ 30 / 2 / 8 / 79.4710
18
23
150 6 150 RGX 395 1060 55 285 11 150 6 821001/1031 N/A15 / 41 / 2 / 180.89
167
101
8
200 8 200 RGX 445 1060 55 340 200 8 1031001/1031 N/A17 ½ 41 / 2 / 13 / 2277
101
86
16
DN Model No. A B C D E F Weightmm in mm in mm in mm in mm in mm in kg lbsmm in
50 2 050 RGX 1011/1021 220 770 N/A 125 5 50 2 42 188 / 30 / 1 / 39.723
38
23
R
Series RGX
Type:
End Connection:
Nominal Sizes:
Model No's: Pressure Ratings bar (psi):
Operating Pressure Range - bar (psi):
Function:
Valve Selection:-
Materials of Construction:-
Installation:-
Standard Factory Tests:
Double Orifice (Small & Large Orifice) with Anti Surge Orificemechanism.
DN50 (2"), DN80 (3"), DN100 (4"), DN150 (6") & DN200 (8")
.PN16 (232 psi) ANSI #125 0.5 (7.2) 16 (232)
i) High volume air/gas discharge - pipeline filling.ii) High volume air intake - pipeline drainingiii) Pressurized air/gas discharge - pipeline filled.iv) Surge dampening - high velocity air/gas discharge,
liquid column separation & liquid oscillation.
see pages 11 & 12
see pages 6 & 8
see page 3
i) Hydrostatic test -1.5 x max. rated working pressureii) Low head leak test - 0.5 bar (7.2 psi)iii) Small orifice function test at max. rated working pressure
(minimum 1 valve in 10).
Flange with DN50 (2") Male BSP/NPT Threaded and ScrewedStuds for Alignment to BS4504, SABS1123 and ANSI B16.1Class 150 for DN80 (3") to DN200 (8").
RGX 16Y1 PN16 (232 psi) ANSI #125
Min Max
OVERALL DIMENSIONS & WEIGHTS
GENERAL SPECIFICATIONSTHREADED 50 (2 & FLANGED - 50 (2”) TO 200 (8") ") EXPANDED BODY
information subject to change without prior noticepage: 10
A
D EA
Note: DN50 (2") valves have DN50 (2") BSP/NPT male inlet connections as standard.
F
B
C
80 3 080 RGX 1601 & 1631 285 780 55 200 80 3 37.511 ¼ 30 / 2 / 7 / 82.67710
18
78 N/A
100 4 100 RGX 1601 & 1631 285 780 55 220 100 4 37 81.5711 ¼ 30 / 2 / 8 /710
18
23 N/A
150 6 150 RGX 1601 & 1631 395 1060 55 285 11 150 6 84.515 / 41 / 2 / 186.39
167
101
8 N/A
200 8 200 RGX 1601 & 1631 445 1060 55 340 200 8 105.5 232.617 ½ 41 / 2 / 13 /7
101
86
16 N/A
DN Model No. A B C D E F Weightmm in mm in mm in mm in mm in mm in kg lbsmm in
50 2 050 RGX 1611 & 1621 220 770 N/A 125 5 50 2 42 21 46.38 / 30 / 1 /23
38
23
R
Series RGX
SELECTION & POSITIONING
information subject to change without prior noticepage: 11
Conversion Table: - l/min. to m/sec. of Pipeline Velocity
VALVE SELECTION GRAPH
300 (12") 200 (8")
80 (3") 50 (2")
150 (6") 100 (4")250 (10")
Pip
e D
ia in m
m
3000
2800
2600
2400
2200
2000
1800
1600
1400
1200
1000
800
600
400
200
Pipeline Flow in m/s
1 2 3 4 5 6 7 8 9 10
Pipeline Flow in ft/s
5 10 15 20 25 30
Pipe Dia
mm 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10
100 4 8 12 16 20 24 27 31 35 39 43 47 51 55 59 63 67 71 75 79
150 9 18 27 35 44 53 62 71 80 88 97 106 115 124 133 141 150 159 168 177
200 16 31 47 63 79 94 110 126 141 157 173 188 204 220 236 251 267 283 298 314
250 25 49 74 98 123 147 172 196 221 245 270 295 319 344 368 393 417 442 466 491
300 35 71 106 141 177 212 247 283 318 353 389 424 459 495 530 565 601 636 672 707
350 48 96 144 192 241 289 337 385 433 481 529 577 625 673 722 770 818 866 914 962
400 63 126 188 251 314 377 440 503 565 628 691 754 817 880 942 1005 1068 1131 1194 1257
450 80 159 239 318 398 477 557 636 716 795 875 954 1034 1113 1193 1272 1352 1431 1511 1590
500 98 196 295 393 491 589 687 785 884 982 1080 1178 1276 1374 1473 1571 1669 1767 1865 1963
550 119 238 356 475 594 713 832 950 1069 1188 1307 1425 1544 1663 1782 1901 2019 2138 2257 2376
600 141 283 424 565 707 848 990 1131 1272 1414 1555 1696 1838 1979 2121 2262 2403 2545 2686 2827
650 166 332 498 664 830 995 1161 1327 1493 1659 1825 1991 2157 2323 2489 2655 2821 2986 3152 3318
700 192 385 577 770 962 1155 1347 1539 1732 1924 2117 2309 2501 2694 2886 3079 3271 3464 3656 3848
750 221 442 663 884 1104 1325 1546 1767 1988 2209 2430 2651 2872 3093 3313 3534 3755 3976 4197 4418
800 251 503 754 1005 1257 1508 1759 2011 2262 2513 2765 3016 3267 3519 3770 4021 4273 4524 4775 5027
850 284 567 851 1135 1419 1702 1986 2270 2554 2837 3121 3405 3688 3972 4256 4540 4823 5107 5391 5675
900 318 636 954 1272 1590 1909 2227 2545 2863 3181 3499 3817 4135 4453 4771 5089 5407 5726 6044 6362
950 354 709 1063 1418 1772 2126 2481 2835 3190 3544 3899 4253 4607 4962 5316 5671 6025 6379 6734 7088
1000 393 785 1178 1571 1963 2356 2749 3142 3534 3927 4320 4712 5105 5498 5890 6283 6676 7069 7461 7854
1100 475 950 1425 1901 2376 2851 3326 3801 4276 4752 5227 5702 6177 6652 7127 7603 8078 8553 9028 9503
1200 565 1131 1696 2262 2827 3393 3958 4524 5089 5655 6220 6786 7351 7917 8482 9048 9613 10179 10744 11310
1300 664 1327 1991 2655 3318 3982 4646 5309 5973 6637 7300 7964 8628 9291 9955 10619 11282 11946 12610 13273
1400 770 1539 2309 3079 3848 4618 5388 6158 6927 7697 8467 9236 10006 10776 11545 12315 13085 13854 14624 15394
1500 884 1767 2651 3534 4418 5301 6185 7069 7952 8836 9719 10603 11486 12370 13254 14137 15021 15904 16788 17671
1600 1005 2011 3016 4021 5027 6032 7037 8042 9048 10053 11058 12064 13069 14074 15080 16085 17090 18096 19101 20106
1700 1135 2270 3405 4540 5675 6809 7944 9079 10214 11349 12484 13619 14754 15889 17024 18158 19293 20428 21563 22698
1800 1272 2545 3817 5089 6362 7634 8906 10179 11451 12723 13996 15268 16540 17813 19085 20358 21630 22902 24175 25447
1900 1418 2835 4253 5671 7088 8506 9924 11341 12759 14176 15594 17012 18429 19847 21265 22682 24100 25518 26935 28353
2000 1571 3142 4712 6283 7854 9425 10996 12566 14137 15708 17279 18850 20420 21991 23562 25133 26704 28274 29845 31416
2100 1732 3464 5195 6927 8659 10391 12123 13854 15586 17318 19050 20782 22513 24245 25977 27709 29441 31172 32904 34636
2200 1901 3801 5702 7603 9503 11404 13305 15205 17106 19007 20907 22808 24709 26609 28510 30411 32311 34212 36113 38013
2300 2077 4155 6232 8310 10387 12464 14542 16619 18696 20774 22851 24929 27006 29083 31161 33238 35315 37393 39470 41548
2400 2262 4524 6786 9048 11310 13572 15834 18096 20358 22619 24881 27143 29405 31667 33929 36191 38453 40715 42977 45239
2500 2454 4909 7363 9817 12272 14726 17181 19635 22089 24544 26998 29452 31907 34361 36816 39270 41724 44179 46633 49087
2600 2655 5309 7964 10619 13273 15928 18583 21237 23892 26546 29201 31856 34510 37165 39820 42474 45129 47784 50438 53093
2700 2863 5726 8588 11451 14314 17177 20039 22902 25765 28628 31491 34353 37216 40079 42942 45804 48667 51530 54393 57256
2800 3079 6158 9236 12315 15394 18473 21551 24630 27709 30788 33866 36945 40024 43103 46181 49260 52339 55418 58496 61575
2900 3303 6605 9908 13210 16513 19816 23118 26421 29723 33026 36329 39631 42934 46236 49539 52842 56144 59447 62749 66052
3000 3534 7069 10603 14137 17671 21206 24740 28274 31809 35343 38877 42412 45946 49480 53014 56549 60083 63617 67152 70686
Pipeline Velocity in Metres per sec
R
Series RGX
SELECTION & POSITIONING
VA
LV
E S
EL
EC
TIO
N F
RO
M G
RA
PH
All
the
rele
van
t in
form
atio
n h
as b
een
co
nd
ense
d in
to o
ne
gra
ph
to
en
able
val
ve s
elec
tio
n t
o b
e si
mp
le a
nd
eas
y an
d a
t th
e sa
me
tim
e to
allo
w f
lexi
bili
ty t
o t
he
des
ign
er t
o m
ove
wit
hin
cer
tain
par
amet
ers
wh
ich
eve
ntu
ally
allo
ws
the
mo
st s
uit
ed a
nd
eco
no
mic
ally
via
ble
val
veto
be
sele
cted
.IM
PO
RTA
NT
NO
TE: T
he
gra
ph
is b
ased
on
vac
uu
m b
reak
ing
an
d li
mit
ing
vac
uu
m t
o 0
.34
bar
(5 p
si) b
elo
w a
tmo
sph
eric
. It
is n
ot
go
od
pra
ctic
e to
go
bel
ow
0.6
9 b
ar (1
0 p
si) a
bso
lute
(0.3
03
bar
(4.4
psi
) dif
fere
nti
al in
pip
elin
e at
sea
leve
l). T
he
gra
ph
allo
ws
for
chan
ge
inal
titu
de
and
hen
ce c
han
ge
in a
tmo
sph
eric
pre
ssu
re a
nd
is b
ased
on
th
e as
sum
pti
on
th
at m
ore
th
an o
ne
valv
e p
er s
ecti
on
is u
sed
fo
r
Sel
ectio
n is
bas
ed o
n th
e pr
emis
e th
at p
ipel
ines
are
gen
eral
ly fi
lled
at a
slo
wer
rat
eth
an th
ey a
re d
rain
ed, s
cour
ed o
r at
whi
ch s
epar
atio
n oc
curs
(a
max
imum
fill/
dra
inra
tio o
f 1:1
).
1.D
eter
min
eth
em
axim
umdr
aina
gera
tein
m/s
eith
erfo
r sco
urin
g,pi
peru
ptur
eor
colu
mn
sepa
ratio
nfo
r apa
rtic
ular
pipe
line
sect
ion.
2.M
ove
vert
ical
lyon
the
grap
hfr
omth
em
/spo
int a
ndm
ove
horiz
onta
llyfr
omth
epi
pesi
zefin
ding
the
inte
rsec
ting
poin
t.3.
Thi
spo
int s
houl
dfa
llw
ithin
the
oper
atin
gba
ndof
apa
rtic
ular
valv
esi
ze.C
onsi
dera
tion
mus
tbe
give
nto
the
fact
that
the
uppe
rpor
tion
ofth
eba
ndap
proa
ches
-0.3
4ba
r (5
psi)
and
the
low
erpo
rtio
n-0
.1ba
r (1.
45ps
i)fo
reac
hva
lve
size
, thi
sal
low
sth
ede
sign
erto
see
ata
glan
ceif
the
valv
eis
too
clos
eto
It's
oper
atin
glim
itsan
dto
sele
ctth
ene
xtva
lve
size
.
AC
TU
AL
SE
LE
CT
ION
( G
RA
VIT
Y O
R P
UM
PE
D P
IPE
LIN
ES
)
EX
AM
PL
E O
F V
AL
VE
SIZ
ING
(AS
SU
MM
ING
AN
IND
IVID
UA
L S
EC
TIO
N)
VA
LV
E P
OS
ITIO
NIN
G1.
ON
AP
EX
PO
INT
S (
rela
tive
to h
ydra
ulic
gra
dien
t).
2.5
ME
TE
RS
(16
FE
ET
) B
ELO
WA
PE
X P
OIN
TS
FO
RM
ED
BY
INT
ER
SE
CT
ION
OF
PIP
ELI
NE
AN
D H
YD
RA
ULI
C G
RA
DIE
NT
- i.e
. whe
re p
ipel
ine
siph
onin
g ov
er
Gra
dien
t a s
ewag
e ai
r re
leas
e va
lve
posi
tione
d on
the
apex
wou
ld b
reak
the
siph
on. I
f pos
ition
ing
on a
pex
is r
equi
red
a m
odifi
ed V
EN
T-O
- M
AT
Ser
ies
RG
X c
an b
esu
pplie
d.
3.N
EG
AT
IVE
BR
EA
KS
(in
crea
se in
dow
nwar
d sl
ope
or d
ecre
ase
in u
pwar
d sl
ope)
.
4.LO
NG
HO
RIZ
ON
TAL
SE
CT
ION
S -
eve
ry 6
00 m
eter
s (1
/3 o
f a m
ile)
max
imum
.
5.LO
NG
AS
CE
ND
ING
SE
CT
ION
S -
eve
ry 6
00 m
eter
s (1
/3 o
f a m
ile)
max
imum
.
6.LO
NG
DE
SC
EN
DIN
G S
EC
TIO
NS
- e
very
600
met
ers
(1/3
of a
mile
) m
axim
um.
7.P
UM
PD
ISC
HA
RG
E (
not s
how
n in
dia
gram
) -
just
sub
sequ
ent t
o no
n re
turn
val
ve.
8.B
LAN
K E
ND
S (
not s
how
n in
dia
gram
) -
whe
re a
pip
elin
e is
term
inat
ed
by a
blin
d fla
nge
or a
val
ve.
information subject to change without prior noticepage: 12
13
21
43
31
33
33
31
53
6
SC
OU
R
GR
AD
IEN
T
MA
Y B
E R
EQ
UIR
ED
FO
R S
CO
UR
ING
SC
OU
R
VA
LV
EH
OR
IZO
NT
AL
DA
TU
M
HY
DR
AU
LIC
GR
AD
IEN
T
A40
0mm
(16"
)pi
pelin
edr
aini
ngat
377l
/sec
whi
cheq
uate
sto
3m/s
ec(1
0ft/s
)w
hat v
alve
size
shou
ldbe
sele
cted
?
Fro
mth
e3m
/sec
(10f
t/s) p
oint
, mov
eve
rtic
ally
until
the
400m
m(1
6") p
ipe
size
horiz
onta
l lin
eis
inte
rsec
ted.
Thi
spl
aces
the
inte
rsec
tion
poin
tsq
uare
lyin
the
cent
reof
the
oper
atin
gba
ndof
aD
N80
(3")
Ven
t -O
-M
atR
GX
valv
e.B
ut, i
f for
exam
ple,
the
drai
nage
rate
is50
3l/s
ecw
hich
equa
tes
to4m
/sec
(13.
2ft/s
),th
eva
lve
wou
ldbe
oper
atin
gon
it's
limit
and
itm
aybe
prud
ent t
och
ange
toa
DN
100
(4")
Ven
t -O
-Mat
RG
X.
Ø
Ø
R
Series RGX
SURGE & WATERHAMMER PROTECTION
Introduction
Surge Protection - Initial Filling
Surge Protection - Pump Trip Conditions
Surge Protection - Pipeline Operating
The Vent-O-Mat Series RGX "Anti-Surge" sewage air release and vacuum break valve, is the product of extensive researchinto the development of an efficient, but cost effective solution to surge problems (both mass liquid oscillation and elastictransient phenomena) associated with any operating pipeline. Automatic dampening, relevant to the pipeline's needs isprovided by either one of three design features. These special features are unique in a pipeline component of suchcompact and economic design.
The RGX incorporates the additional floating "Anti-Surge" Orifice which is aerodynamically engineered to throttle airdischarge when liquid approach velocity would otherwise become too great and induce an unacceptable pressure rise. Theair throttling action increases resistance to the flow of the approaching liquid which consequently decelerates to a velocitywhich reduces the pressure rise when the valve closes (see operation of valve on pages 1 & 2). Vent-O-Mat series RGX isan essential precaution for pipeline priming.
In instances where a pipeline experiences liquid column separation due to pump stoppage, high shock pressures can begenerated when the separated liquid column rejoins.
The Vent-O-Mat series RGX takes in air through the unobstructed large orifice when liquid column separation occurs, butcontrols the discharge of air/gas through the "Anti-Surge" Orifice as the separated column commences to rejoin. Therejoining impact velocity is thereby considerably reduced to alleviate high surge pressures in the system (see operation ofvalve on pages 1 & 2).
Other surge control measures may, dependant on pipeline profile, diameter and operating conditions, be needed to providethe primary surge alleviation function with the Vent-O-Mat sewage air-valves forming an integral and valuable addition in acombined strategy for further reducing surge pressures. The benefit of the "Anti-Surge" Orifice can be readilydemonstrated by suitable surge modelling software.
The operation of valves and similar flow control devices can cause high-pressure transients in an operating pipeline.
The unique, single chamber design of the Vent-O-Mat series RGX valve enables a pocket of air to be trapped in the valvechamber.Automatic operation of the small orifice control float regulates the volume of air entrapped.
The volume maintained in the valve will provide a cushioning benefit to the pipeline for short duration transient pressure"spikes". This effect can be modelled by the design engineer using suitable surge software.
information subject to change without prior noticepage: 13
R
Series RGX
SURGE & WATERHAMMER PROTECTION
Computer Modelling
Holistic Surge & Water Hammer Protection
Technical and Financial Benefits
S e r v i c e
The effectiveness of Vent-O-Mat series RGX has been substantiated by independent third party testing and bythousands of applications globally. Effective computer modelling, based on practical tests, has been ensured in the well-known and respected commercially available surge analysis software programmes such as AFT impulse,FLOWMASTER, TRANSAM and
Vent-O-Mat forms an integral part of a well planned, holistic surge protection strategy that should, according toapplication needs and financial constraints, include surge vessels, check valves, control valves and/or any otherequipment needed to alleviate unacceptable surge behaviour.
The Vent-O-Mat series RGX valve offers definite financial and technical advantages when incorporated as part of aholistic surge protection strategy. This includes:
1. Improved alleviation of surge behaviour including reduction of:- Surge pressure magnitudes by slowing surge velocities- Duration of oscillation following a pump trip, as the sewage air-valve continuously absorbs anddissipates the energies of the surge.
2. Potential for reduction in size and/or quantity of conventional surge protection devices such as surge vessels etc.
3. Automatic protection during initial filling when most surge protection devices are not operational.
4. Holistic protection as each sewage air valve installed has design features to automatically damp surges.
5. The valve is virtually maintenance free.
Vent-O-Mat is committed to finding the most cost effective and efficient solution to pipeline complexities. Servicesinclude air valve sizing and positioning and assistance to consulting engineers on defining appropriate surge and waterhammer protection strategies. Vent-O-Mat has built a sound relationship with many international consulting firms andhas gained global recognition for selling solutions!
SURGE 2000.
information subject to change without prior noticepage: 14
R
Series RGXSMALL ORIFICE DISCHARGE PERFORMANCE
Type:
Model No's:
Series RGX - Double Orifice (Small & Large Orifice)with "Anti-Surge" Orifice Mechanism
RGX 1001/1011/1021/1031RGX 1601/1611/1621/1631RGX 2501/2511/2521/2531
¨ 2mm (0.07") small orifice - DN50 (2"), DN80 (3"),Dn100 (4") Valves
¨ 5mm (0.20") small orifice - DN150 (6") Valves
¨ 6mm (0.24") small orifice - DN200 (8") Valves
information subject to change without prior noticepage: 15
Q (scf/min.)
FOR HIGHER p OR DISCHARGERATES CONSULT MANUFACTURER
ª
15 30 45 60 75 90 105
P(bar)ª
20
25
18
16
14
12
10
8
6
4
2
0
Q (nl/s)
7 14 21 28 35 42 49
Q = Normal Litresper second (Free Air)@ 1.01325 bar Abs.and 20 deg. C
Q = Standard Cubic Feetper minute (Free Air)@ 14.7 psi Abs.68 deg. F
1
CONVERSION EQUIVALENTS1 l/ sec. = 2.1189 scf/ min. 1 scf/ min = 0.472 l/ sec.
1 bar = 14.5 psi 1 psi = 0.069 bar
R
Series RGXWhy?
information subject to change without prior noticepage: 16
"ANTI - SHOCK" - "ANTI - SURGE"
PERFORMANCE
QUALITY
SERVICEABILITY
VACUUM BREAK
COMPACTNESS
BACK UP
- The RGX is the only air release valve available that is supplied
as standard with a mechanism which operates automatically to prevent pipeline damage from the highinduced pressure transients associated with high velocity air discharge. Surge resulting from liquidcolumn separation and liquid oscillation is dramatically reduced as an automatic function of thismechanism.
- The RGX has been designed and developed to provide the optimum usable and
safe performance relative to all functions. Selection data has been substantiated through CSIR* andother testing and can therefore, be confidently referenced.
- The RGX economically offers the highest quality construction and materials available in an
air release and vacuum break valve. Stringent manufacturing and test procedures are maintained toensure the best possible service and reliability is given by every valve produced.
- The RGX design facilitates extreme ease of service and maintenance.
Components are in corrosion free materials to allow problem free disassembly and reassembly evenafter many years of operation.All maintenance spares are replaceable without special tools or skills.
- The RGX series large orifice diameters equal the nominal size of the valve, i.e., a
200mm (8") valve has a 200mm (8") orifice. This ensures the least possible resistance to the intake of airand consequently the least possible negative pressure within a draining pipeline.
- Although extremely robust the RGX valve's lightweight and compact construction
offers handling transport and installation advantages.
- Vent -O- Mat provides highly committed customer orientated sales, service, spares and
technical back up - TRY US!!!
* Council for Scientific and Industrial Research
R
Series RGX
PURCHASE SPECIFICATION
information subject to change without prior noticepage: 17
VENT -O- MAT MODEL NO.
CONSTRUCTION & DESIGN
Nuts and washersshall be excluded.
OPERATION
Page 9 - Series RGX - DN50 (2") to DN200 (8").
The Sewage Air Release & Vacuum Break Valve shall consist of a compact tubular all stainless steel fabricatedbody, hollow direct acting float and solid large orifice float in H.D.P.E. - stainless steel nozzle and woven dirtinhibitor screen, EPDM rubber seals and seat.
The valve shall have an integral "Anti-Surge" Orifice mechanism which shall operate automatically to limittransient pressure rise or shock induced by closure to less than 1.5 x valve rated working pressure.
The intake orifice area shall be equal to the nominal size of the valve i.e., a 150mm (6") valve shall have a150mm (6") intake orifice. Large orifice sealing shall be effected by the flat face of the control float seatingagainst a EPDM rubber 'O' ring housed in a dovetail groove circumferentially surrounding the orifice.
Discharge of pressurized air shall be controlled by the seating & unseating of a small orifice nozzle on a naturalrubber seal affixed into the control float. The nozzle shall have a flat seating land surrounding the orifice so thatdamage to the rubber seal is prevented.The valve construction shall be proportioned with regard to material strength characteristics, so thatdeformation, leaking or damage of any kind does not occur by submission to twice the designed workingpressure.Connection to the valve inlet shall be facilitated by flanged ends conforming to PN10, 16 or 25 ratings ofBS4504 or SABS 1123 Standards or ANSI B16.1 Class 125 & Class 250 and ANSI B16.5 Class 150 or Class300 Standards. AS 4087 Fig. B7 - B9, AS 2129 Table E/F. Flanged ends shall be supplied with the requisitenumber of stainless steel screwed studs inserted for alignment to the specified standard.
1. Prior to the ingress of liquid into the valve chamber, as when the pipeline is being filled, valves shallvent through the large orifice when sewage/effluent approach velocities are relative to a transientpressure rise, on valve closure, of < 1.5 x valve rated pressure.At higher sewage/effluent approach velocities, which have a potential to induce transient pressure rises> 1.5 x valve rated pressure on valve closure, the valve shall automatically discharge air/gas throughthe "Anti-Surge" Orifice and reduce sewage/effluent approach velocity, so that on closure a maximumTransient pressure rise of < 1.5 x valve rated pressure is realised.
2. Valves shall not exhibit leaks or weeping of liquid past the large orifice seal at operating pressures of0,5 bar (7.2 psi) to 1.5 x valve rated working pressure.
3. Valves shall respond to the presence of air/gas by discharging it through the small orifice at anypressures within a specified design range, i.e. 0,5 bar (7.2 psi) to 10 bar (145 psi) and shall remainleak tight in the absence of air.
4. Valves shall react immediately to pipeline drainage or liquid column separation by the full opening of thelarge orifice so as to allow unobstructed air intake at the lowest possible negative internal pipelinepressure.
Page 10 - Series RGX - DN50 (2") to DN200 (8"). (Expanded Body)
R
Series RGX
ORDERING GUIDE
VALVE SERIES No.
ANTI-SURGE ORIFICE:
VALVE TYPE:DOUBLE ACTING 1
0 5 0 R G X 1 0 1 1
information subject to change without prior noticepage: 18
VALVE SIZE:DN50 (2") - 0 5 0
DN80 (3") - 0 8 0
DN100 (4") - 1 0 0
DN150 (6") - 1 5 0
DN200 (8") - 2 0 0
VALVE PRESSURE RATING:PN10 (145 psi) ANSI #125 1 0
PN16 (232 psi) ANSI #250 1 6
VALVE END CONNECTION:STUDDED FLANGED - BS4504 or SABS 1123 0THREADED - BSP MALE 1THREADED - NPT MALE 2STUDDED FLANGED - ANSI B16.5 3
Note:
All air release valves supplied shall be subjected to the following testing procedures in the orderlaid down:
IMPORTANT NOTE:
1. DN250 (10”) and DN300 (12”) valves are available on request.
(A) A high pressure strength and leak test whereby the valve is filled with water and pressurized to twice the ratedworking pressure which shall be held for a period of 2 minutes. Any leaking, weeping or sweating shall bereason for rejection.
(B) A low head leak test whereby the valve is filled with water and pressurized to a maximum of 0,5 bar (7.2 psi)using a visible water column connected to the test rig. The valve shall be rejected if leak tightness is notmaintained for 2 minutes.
(C) Every tenth air release valve of the same size and pressure rating must be subjected to a small orifice function test"DROP TEST" - whereby the valve is filled with water, pressurized to above rated working pressure and isolatedfrom the test rig by closure of an isolating valve. A chamber in the test rig immediately prior to the isolating valvemust be filled with compressed air at a pressure equal to that being maintained in the air release valve. Theisolating valve is then opened so as to allow the air to rise in the air release valve without the pressure droppinglower than 2 - 3 bar (29 - 44 psi) above rated working pressure of the air release valve. The "DROP TEST" is thencarried out by slowly bleeding off the pressure through a suitable cock until rated working pressure is reached andthe float drops away from the orifice to allow discharge. Failure of the air release valve to function in the mannerdescribed will be reason for rejection.
On request the manufacturer shall provide batch certificates of test compliance which shall be cross referenced to serialnumbers indelibly marked onto the identity label of each valve.
It is impossible to inject air into an incompressible liquid, air injection can only be achieved if the
liquid can be displaced which implies that the pressure in the test rig must be reduced to atmospheric, and absolutelynothing is proven by discharge through the small orifice of the air release valve at atmospheric pressure. "DROP TESTING"in this manner is not acceptable.
TEST SPECIFICATION
R
Series RGXb
OPERATION
VENTING(PUMP START UP)
2
"Anti - Surge" Orifice
"Anti - Surge" Float
information subject to change without prior notice
page: 19
PRESSURIZED AIR/GAS RELEASEPUMP OPERATING
4
Normal Operating Level(Small Orifice ControlFloat Buoyancy Level)
10 bar (145 psi)Working Pressure
Maximum Surge Level
VACUUM RELIEF (AIR INTAKE)PIPELINE DRAINING
1
PIPELINE FULLY CHARGED
3
PRE NOTES:
VACUUM RELIEF (AIR INTAKE)
VENTING (PUMP START UP)
PRESSURIZED AIR RELEASE FROM A FULL PIPELINE
PRESSURIZED AIR RELEASE (PUMP OPERATING)
It is good engineering practice to install a sewage air valve prior to the pump discharge check valve, on vertical turbinepumps and deepwell submersible pump applications. The purpose of these valves is to control air/gas entry into the mainpipeline on initial pump start up and to fully break vacuum in the vertical riser upon pump shutoff.
Operation of conventional sewage air valves in this application is such that the air in the vertical riser is released very rapidlyupon pump startup, resulting in very high pressure transients when the liquid column slams the sewage air valve shut and/orslams into the closed discharge check valve.
The Vent-O-Mat Series RGXb valve has specifically been developed for use on deep well submersible pump and verticalturbine pump applications where they are installed prior to the pump discharge check valve to fulfill the following functions:
Provide effective release of air/gas in the vertical riser upon pump startup.
Dampen surge pressures upon startup.
Provide vacuum protection when the pump stops and the vertical column drains.
Upon pump stop, the discharge check valve closes. Sewage/effluent drains from the sewage air valve and the pump'svertical column. The negative differential created by the draining liquid causes atmospheric air to push the "Anti-Surge" Floatdown, opening the Large Orifice and allows air to displace the draining liquid to prevent potentialy damaging internalnegative pressure*.The hollow smooth side float design, discourages the adherence of solids and viscous substances which, therefore tend towithdraw from the valve into the pipeline when draining occurs, for this reason
Air/gas is forced through the "Anti-Surge" Orifice resulting in the deceleration of the approaching liquid column due to theresistance of rising air pressure in the valve.This dampens transients when the sewage air valve closes and the liquid column opens the discharge check valve.
Sewage/effluent has entered the valve chamber and buoyed the floats to close both the "Anti-Surge" orifice and the smallorifice. The design's compression/volume relationship prevents the media from ever exceeding the maximum surge levelindicated in diagram 3. The resultant sewage/effluent free area protects against the fouling of the orifice seals by solids orhigh viscous substances - for this reason
The volume of disentrained air/gas increases in the valve and displaces the sewage/effluent level to the lower, normaloperating level (small orifice control float buoyancy level ) Any additional lowering of the sewage/effluent level, as wouldoccur when more air/gas enters the valve, will result in the control float dropping away from the small orifice through whichpressurized air/gas is then being discharged to atmosphere.The control float will close the small orifice when sufficient air/gas has been released to restore the sewage/effluent level tothe normal operating level.The considerable sewage/effluent free are obviates the possibility of leaks that could otherwise be caused by solids enteringthe sealing areas - for this reason
A differential pressure of less than 0.05 bar (0.7 psi) across the large orifice is required to open the valve fully under vacuumconditions.
NO FLUSHING CONNECTIONS ARENECESSARY
NO FLUSHING CONNECTIONS ARE NECESSARY.
NO FLUSHING CONNECTIONS ARE NECESSARY
*Note:
�
�
�
R
page: 20
Series RGXb
OPERATION
1.
2.
3.
4.
R
RECOMMENDED INSTALLATION ARRANGEMENTS
Series RGXb
page: 21
CENTRIFUGAL PUMP APPLICATION
Pump
R
Series RGXb
information subject to change without prior noticepage: 22
Top CoverStainless Steel AISI 304
Adjusting RodStainless Steel AISI 304
SpringStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
Top FlangeStainless Steel AISI 304
Locating DiskStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304 O - Ring Seal
EPDM Rubber
NutsStainless Steel AISI 304
StudsStainless Steel AISI 304L
Upper FloatHigh Density Polyethylene
Connecting ScrewsCheeseheadStainless Steel AISI 304
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
Connecting BracketStainless Steel AISI 304
O - Ring SeatEPDM Rubber
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
BodyStainless Steel AISI 304L
Anti-Surge Orifice FloatHigh Density Polyethylene
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONTHREADED 50 (2") & STUDDED INLET - 80 (3)" TO 100 (4")
Note: 50 (2
Valves are available in AISI 316L on request.
") Threaded BSP/NPT Male Inlet
O - Ring SealEPDM Rubber
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXb -Double Orifice (Small & Large Orifice)with Mechanism
DN50 (2") RGXb 1011/1021 PN10 (145 psi)DN80 (3")
Flange with Threaded BSP/NPT Male - 50 (2") valves.Flange with Screwed Studs - 80 (3") & 100 (4") valves.
RGXb 1001/1031 PN10 (145 psi)
Bias
R
StudsStainless Steel AISI 304L
BodyStainless Steel AISI 304L
Series RGXb
page: 23
Top CoverStainless Steel AISI 304
Adjusting RodStainless Steel AISI 304
SpringStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Anti-Surge Orifice FloatHigh Density Polyethylene
Top FlangeStainless Steel AISI 304
Locating DiskStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
NutsStainless Steel AISI 304
Connecting ScrewsCheeseheadStainless Steel AISI 304
information subject to change without prior notice
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
Connecting BracketStainless Steel AISI 304
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXb - Double Orifice (Small & Large Orifice)with Mechanism
DN50 (2") RGXb 1611/1621 PN16 (232 psi)DN80 (3”)
“Flange with Threaded BSP/NPT Male - 50 (2") valves.Flange with Screwed Studs - 80 (3") & 100 (4") valves
RGXb 1601/1631 PN16 (232 psi)DN100 (4")
Bias
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONTHREADED 50 (2") & STUDDED INLET - 80 (3") TO 100 (4") EXPANDED BODY
O - Ring SealEPDM Rubber
Upper FloatHigh Density Polyethylene
Note: 50 (2
Valves are available in AISI 316L on request.
") Threaded BSP/NPT Male Inlet
O - Ring SealEPDM Rubber
R
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXb -Double Orifice (Small & Large Orifice) Flange with Screwed Studs - 150 (6 & 200 (8 valves.with Mechanism
DN150 (6") RGXb 1001/1031 PN10 (145 psi)DN200 (8")
") ")Bias
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONSTUDDED INLET - 150 (6") & 200 (8")
Series RGXb
information subject to change without prior notice
page: 24
Top CoverStainless Steel AISI 304
Adjusting RodStainless Steel AISI 304
SpringStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
Top FlangeStainless Steel AISI 304
Locating DiskStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
O - Ring SealEPDM Rubber
Anti-Surge Orifice FloatHigh Density Polyethylene
NutsStainless Steel AISI 304
StudsStainless Steel AISI 304L
Upper FloatHigh Density Polyethylene
Connecting ScrewsCheeseheadStainless Steel AISI 304
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
Float ScrewStainless Steel AISI 304
O - Ring SeatEPDM Rubber
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
BodyStainless Steel AISI 304L
O - Ring SealEPDM Rubber
R
StudsStainless Steel AISI 304L
Series RGXb
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXb - Double Orifice (Small & Large) withMechanism
DN150 (6") RGXb 1601/1631 PN16 (232 psi)Dn200 (8")
Flange with Screwed Studs - 150 (6") & 200 (8") valves.Bias
information subject to change without prior noticepage: 25
Top CoverStainless Steel AISI 304
Adjusting RodStainless Steel AISI 304
SpringStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Anti-Surge Orifice FloatHigh Density Polyethylene
Top FlangeStainless Steel AISI 304
Locating DiskStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
NutsStainless Steel AISI 304
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
Float ScrewStainless Steel AISI 304
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
Upper FloatHigh Density Polyethylene
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONSTUDDED INLET - 150 (6") & 200 (8") EXPANDED BODY
O - Ring SealEPDM Rubber
O - Ring SealEPDM Rubber
R
Type:
End Connection:
Nominal Sizes:
Model No's: Pressure Ratings - bar (psi):
Operating Pressure Range - psi:
Function:
Valve Selection:-
Materials of Construction:-
Installation:-
Standard Factory Tests:
Double Orifice (Small & Large Orifice) with mechanism forlarge volume air intake and controlled air discharge.
DN50 (2"), DN80 (3"), DN100 (4"), DN150 (6") & DN200 (8")
RGXb 1011/1021 PN10 (145 psi)
Min Max.PN10 (145 psi) 0.5 (7.2) 10 (145)
i) High volume air intake - pipeline drainingii) Pressurized air/gas discharge - pipeline filled.iii) Controlled air discharge - pipeline filling.iv) Surge dampening - high velocity air/gas discharge,
liquid column separation & liquid oscillation.
see pages 11 & 12
see pages 22 & 24
see page 21
i) Hydrostatic test -1.5 x max. rated working pressureii) Low head leak test - 0.5 bar (7.2 psi)iii) Small orifice function test at max. rated working pressure
(minimum 1 valve in 10).
Bias
Flange with DN50 (2") Male BSP/NPT Threaded and ScrewedStuds for Alignment to BS4504, SABS 1123 or ANSI B16.5Class 150 for DN80 (3") to DN200 (8").
RGXb 1001/1031 PN10 (145 psi)
Series RGXb
page: 26
information subject to change without prior notice
R
DE A
A
OVERALL DIMENSIONS & WEIGHTS
GENERAL SPECIFICATIONSTHREADED 50 (2 & STUDDED INLET - 80 (3") TO 200 (8") ")
C
B
F
80 3 080 RGXb 1001 & 1031 285 885 55 200 80 3 36.711 ¼ 2 / 7 / 80.934 /78
18
78 N/A
100 4 100 RGXb 1001 & 1031 285 885 55 220 100 4 36.211 ¼ 2 / 8 / 79.834 /78
18
23 N/A
150 6 150 RGXb 1001 & 1031 395 1230 55 285 11 150 6 82.415 / 2 / 181.79
161
848 /4
10 N/A
200 8 200 RGXb 1001 & 1031 445 1230 55 340 200 8 103.417 ½ 2 / 13 / 227.948 /4
101
86
16 N/A
DN Model No. A B C D E F Weightmm in mm in mm in mm in mm in mm in kg lbsmm in
50 2 050 RGXb 1011 & 1021 220 850 N/A 125 5 50 2 42 18.18 / 1 / 39.923
2333 /
716
R
Series RGXb
page: 27
information subject to change without prior notice
R
OVERALL DIMENSIONS & WEIGHTS
DE A
A
F
B
C
GENERAL SPECIFICATIONSTHREADED 50 (2 & STUDDED INLET - 80 (3") TO 200 (8") ") EXPANDED BODY
80 3 080 RGXb 1001 & 1031 285 885 55 200 80 3 3811 ¼ 2 / 7 /34 /78
18
78 N/A 84.1
100 4 100 RGXb 1001 & 1031 285 885 55 220 100 4 37.511 ¼ 2 / 8 /34 /78
18
23 N/A 83
150 6 150 RGXb 1001 & 1031 395 1230 55 285 11 150 6 8515 / 2 /9
161
848 /4
10 N/A 187.2
200 8 200 RGXb 1001 & 1031 445 1230 55 340 200 8 105.817 ½ 2 / 13 /48 /4
101
86
16 N/A 233.4
DN Model No. A B C D E F Weightmm in mm in mm in mm in mm in mm in kg lbsmm in
50 2 050 RGXb 1011 & 1021 220 850 N/A 125 5 50 2 428 / 1 / 2123
2333 /
716 46.5
Type:
End Connection:
Nominal Sizes:
Model No's: Pressure Ratings - bar (psi):
Operating Pressure Range - bar (psi):
Function:
Valve Selection:-
Materials of Construction:-
Standard Factory Tests:
Double Orifice (Small & Large Orifice) with mechanism for largevolume air intake and controlled air discharge.
DN50 (2"), DN80 (3"), DN100 (4"), DN150 (6") & DN200 (8
RGXb 1611/1621 PN16 (232 psi)
Min Max.
i) High volume air intake - pipeline drainingii) Pressurized air/gas discharge - pipeline filled.iii) Surge dampening - high velocity air/gas discharge,
Liquid column separation & liquid oscillation.
see pages 11 & 12
see pages 23 & 25
i) Hydrostatic test -1.5 x max. rated working pressure.ii) Low head leak test - 0.5 bar (7.2 psi).iii) Small orifice function test at max. rated working pressure
(minimum 1 valve in 10).
Bias
Flange with DN50 (2") Male BSP/NPT Threaded and Screwed Studsfor Alignment to BS4504, SABS 1123 or ANSI B16.5 Class 150 &Class 300 for DN80 (3") to DN200 (8").
")
RGXb 1601/1631 PN16 (232 psi)
PN16 (232 psi) 0.5 (7.2) 16 (232)
R
Series RGXb
PURCHASE SPECIFICATION
information subject to change without prior notice
page: 28revision date: April '10
VENT-O-MAT MODEL NO.
OPERATION
The Sewage Air Release & Vacuum Break Valve shall consist of a compact tubular all stainless steelfabricated body, hollow direct acting float and solid large orifice float in H.D.P.E. - stainless steel nozzleand woven dirt inhibitor screen, EPDM rubber seals and seat.
The valve shall have an integral 'Anti-Surge' Orifice mechanism which shall operate automatically to limitsurge pressures or shock induced by liquid oscillation and/or rapid air/gas discharge to less than 1.5 xv a l v e r a t e d w o r k i n g p r e s s u r e .
The intake orifice area shall be equal to the nominal size of the valve i.e., a DN150 (6") valve shall havea DN150 (6") intake orifice. Large orifice sealing shall be effected by the flat face of the control floatseating against a EPDM rubber 'O' ring housed in a dovetail groove circumferentially surrounding theo r i f i c e .
Discharge of pressurized air shall be controlled by the seating & unseating of a small orifice nozzle on aEPDM rubber seal affixed into the control float. The nozzle shall have a flat seating land surrounding theorifice so that damage to the rubber seal is prevented.The valve construction shall be proportioned with regard to material strength characteristics, so thatdeformation, leaking or damage of any kind does not occur by submission to twice the designed workingpressure
Flanged ends shall besupplied with the requisite number of stainless steel screwed studs inserted for alignment to thespecified standard.
1. Prior to the ingress of liquid into the valve chamber, as when the pipeline is being filled, valves shall ventthrough the "Anti-Surge" orifice when sewage/effluent approach velocities are relative to a transientpressure rise, on valve closure, of < 1.5 x valve rated pressure.
2. Valves shall not exhibit leaks or weeping of liquid past the large orifice seal at operating pressures of 0.5bar (7.2 psi) to 1.5 x rated working pressure.
3. Valves shall respond to the presence of air/gas by discharging it through the small orifice at any pressureswithin a specified design range, i.e. 0.5 bar (7.2 psi) to 10 bar (145 psi) and shall remain leak tight in theabsence of air.
4. Valves shall react immediately to pipeline drainage or water column separation by the full opening of thelarge orifice so as to allow unobstructed air intake at the lowest possible negative internal pipelinepressure.
Connection to the valve inlet shall be facilitated by flanged ends conforming to PN10, 16 or 25 ratings ofBS4504 or SABS 1123 Standards or ANSI B16,5 Class 150 or Class 300 Standards.
Nuts and washers shall be excluded.
Page 26 - Series RGXb - DN50 (2") to DN200 (8").Page 27 - Series RGXb - DN50 (2") to DN200 (8") (Expanded Body).
CONSTRUCTION & DESIGN
R
Series RGXv
OPERATION
VENTING OF A FILLING PIPELINE(SUB CRITICAL SEWAGE/ EFFLUENT
APPROACH VELOCITY)
"Anti - Surge" Orifice
Upper Chamber Float
information subject to change without prior notice
page: 29
1
VENTING OF A FILLING PIPELINE(EXCESSIVE SEWAGE/ EFFLUENT
APPROACH VELOCITY)
2
PIPELINE FULLY CHARGED
3
Maximum Surge Level
PRESSURIZED AIR/GAS RELEASEFROM A FULL PIPELINE
4
Normal Operating Level(Small Orifice ControlFloat Buoyancy Level)
10 bar (145 psi)Working Pressure
PRE NOTES:
VENTING OF A FILLING PIPELINE (SUB CRITICAL LIQUID APPROACH VELOCITY)
VENTING OF A FILLING PIPELINE (EXCESSIVE LIQUID APPROACH VELOCITY)
PRESSURIZED AIR/GAS RELEASE FROM A FULL PIPELINE
PRESSURIZED AIR/GAS RELEASE (PUMP OPERATING)
There are instances where the hydraulic gradeline falls below a peak point during normal operation and where airinflow would adversely affect the normal operation and surge characteristic of the pipeline.
Vent-O-Mat offers the Series RGXv valve which has specifically been developed to ensure effective air/gasrelease under all pipeline conditions but will not allow air entry into the pipeline.
Air/gas flows through the annular space between the cylindrical floats and discharges through the Large Orificeinto atmosphere.*
In reaction to increased air/gas flow,"Anti Surge" Float closes the large orifice and air is forced through the "Anti-Surge" orifice resulting in deceleration of the approaching liquid due to the resistance of rising air/gas pressure inthe valve.
Sewage/effluent has entered the valve chamber and buoyed the floats to close both the "Anti-Surge" orifice andthe small orifice. The design's compression/volume relationship prevents the media from ever exceeding themaximum surge level indicated in diagram 3.
The resultant sewage/effluent free area protects against the fouling of the orifice seals by solids or high viscoussubstances - for this reason NO FLUSHING CONNECTIONSARE NECESSARY.
The volume of disentrained air/gas increases in the valve and displaces the sewage/effluent level to the lower,normal operating level (small orifice control float buoyancy level ) Any additional lowering of the sewage/effluentlevel, as would occur when more air/gas enters the valve, will result in the control float dropping away from thesmall orifice through which pressurized air/gas is then being discharged to atmosphere.
The control float will close the small orifice when sufficient air/gas has been released to restore thesewage/effluent level to the normal operating level.
The considerable sewage/effluent free are obviates the possibility of leaks that could otherwise be caused bysolids entering the sealing areas - for this reason NO FLUSHING CONNECTIONSARE NECESSARY
A relatively low flow discharge rate is required to lift the upper chamber float and ensure air release . The UpperChamber Float will seat on the Middle Flange under vacuum conditions, effectively preventing air entry.
*Note:
R
page: 30
Series RGXv
OPERATION
1.
2.
4.
3.
R
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Vent FloatHigh Density Polyethylene
Upper FloatHigh Density Polyethylene
Nozzle Seat Retaining PlateStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
O-Ring SeatEPDM Rubber
NozzleStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
O - Ring SeatEPDM Rubber
Connecting BracketStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
Series RGXv
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXv - Triple Orifice with "Anti-Surge"Mechanism
DN50 (2 ) RGXv 1011/1021 PN10 (145 psi)
Flange with Threaded BSP/NPT Male - 50 (2") valves.Flange with Screwed Studs - 80 (3") & 100 (4") valves.
DN80 (3 ) RGXv 1001/1031 PN10 (145 psi)
DN100 (4 )
”
”
”
information subject to change without prior notice
page: 31
StudsStainless Steel AISI 304L
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONTHREADED 50 (2") & ")STUDDED INLET - 80 (3") TO 100 (4
O - Ring SealEPDM Rubber
Note: 50 (2
Valves are available in AISI 316L on request.
") Threaded BSP/NPT Male Inlet
R
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Upper FloatHigh Density Polyethylene
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
Vent FloatHigh Density Polyethylene
O-Ring SeatEPDM Rubber
Connecting BracketStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
O - Ring SeatEPDM Rubber
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
Series RGXv
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXv - Triple Orifice with "Anti-Surge"Mechanism
DN50 (2") RGXv 1611/1621 PN16 (232 psi)Dn80 (3”)DN100 (4
Flange with Threaded BSP/NPT Male - 50 (2") valves.Flange with Screwed Studs - 80 (3") & 100 (4") valves.
RGXv 1601/1631 PN16 (232 psi)")
information subject to change without prior noticepage: 32
StudsStainless Steel AISI 304L
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONTHREADED 50 (2") & ") EXPANDED BODYSTUDDED INLET - 80 (3") TO 100 (4
O - Ring SeatEPDM Rubber
Note: 50 (2
Valves are available in AISI 316L on request.
") Threaded BSP/NPT Male Inlet
R
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Assembly ScrewsCheeseheadStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Vent FloatHigh Density Polyethylene
Upper FloatHigh Density Polyethylene
Nozzle Seat Retaining PlateStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
O-Ring SeatEPDM Rubber
NozzleStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
O - Ring SeatEPDM Rubber
Float ScrewStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
Series RGXv
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXv - Triple Orifice with "Anti-Surge"Mechanism.
DN150 (6") RGXv 1001/1031 PN10 (145 psi)DN200 (8")
Flange with Screwed Studs - 150 (6") & 200 (8") valves.
information subject to change without prior notice
page: 33
StudsStainless Steel AISI 304L
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONSTUDDED INLET - 150 (6") & 200 (8")
R
Top CoverStainless Steel AISI 304
SpacerGrey P.V.C.
Top Cover Hex BoltStainless Steel AISI 304
O - Ring SealEPDM Rubber
Top FlangeStainless Steel AISI 304
Screen MeshStainless Steel AISI 304
BoltsStainless Steel AISI 304
Upper FloatHigh Density Polyethylene
NozzleStainless Steel AISI 304
Nozzle SeatEPDM Rubber
NutsStainless Steel AISI 304
Vent FloatHigh Density Polyethylene
O-Ring SeatEPDM Rubber
Float ScrewStainless Steel AISI 304
Anti-Surge Orifice FloatHigh Density Polyethylene
O - Ring SeatEPDM Rubber
Nozzle Seat Retaining PlateStainless Steel AISI 304
Lower Float AssemblyHigh Density Polyethylene
Connecting ScrewsCheeseheadStainless Steel AISI 304
BodyStainless Steel AISI 304L
Series RGXv
Type: End Connection:
Nominal Sizes: Model No's: Pressure Ratings:
Series RGXv - Triple Orifice with "Anti-Surge"Mechanism.
DN150 (6") RGXv 1601/1631 PN16 (232 psi)Dn200 (8")
Flange with Screwed Studs - 150 (6") & 200 (8") valves.
information subject to change without prior noticepage: 34
StudsStainless Steel AISI 304L
COMPONENT DESCRIPTION & MATERIAL SPECIFICATIONSTUDDED INLET - 150 (6") & 200 (8") EXPANDED BODY
R
Type:
End Connection:
Nominal Sizes:
Model No's: Pressure Ratings - bar (psi):
Operating Pressure Range - bar (psi):
Function:
Valve Selection:-
Materials of Construction:-
Installation:-
Standard Factory Tests:
Triple Orifice with mechanism for air/gas discharge but not airre-entry.
DN50 (2"), DN80 (3"), DN100 (4"), DN150 (6") & DN200 (8")
RGXb 1011/1021 PN10 (145 psi)
Min Max.PN10 (145 psi) 0.5 (7.2) 10 (145)
i) High volume air/gas discharge - pipeline filling.ii) Pressurized air/gas discharge - pipeline filled.iii) Surge dampening - high velocity air/gas discharge,
liquid column separation & liquid oscillation.
see pages 11 & 12
see pages 31 & 33
see page 3
i) Hydrostatic test - 1.5 x max. Rated working pressureii) Low head leak test - 0.5 bar (7,2 psi)iii) Small orifice function test at max. rated working pressure
(minimum 1 valve in 10).
Bias
Flange with DN50 (2") Male BSP/NPT Threaded and ScrewedStuds for Alignment to BS4504, SABS1123 or ANSI B16.5 Class150 for DN80 (3") to DN200 (8").
RGXb 1001/1031 PN10 (145 psi)
Series RGXv
page: 35
information subject to change without prior notice
Note: DN50 (2") valves have DN50 (2") BSP/NPT male inlet connections as standard.
R
OVERALL DIMENSIONS & WEIGHTS
DE A
A
GENERAL SPECIFICATIONSTHREADED 50 (2 STUDDED INLET - 80 (3") TO 200 (8 )") & "
C
B
F
80 3 080 RGXv 1001 & 1031 285 872 55 200 80 3 36.711 ¼ 2 / 7 / 80.934 /13
18
78 N/A
100 4 100 RGXv 1001 & 1031 285 872 55 220 100 4 36.211 ¼ 2 / 8 / 79.834 /13
18
23 N/A
150 6 150 RGXv 1001 & 1031 395 1225 55 285 11 150 6 82.415 / 2 / 181.79
161
848 /2
10 N/A
200 8 200 RGXv 1001 & 1031 445 1225 55 340 200 8 103.417 ½ 2 / 13 / 227.948 /2
101
86
16 N/A
DN Model No. A B C D E F Weightmm in mm in mm in mm in mm in mm in kg lbsmm in
50 2 050 RGXv 1011 & 1021 220 862 N/A 125 5 50 2 42 18.18 / 1 / 39.923
2334
R
Type:
End Connection:
Nominal Sizes:
Model No's: Pressure Ratings - psi:
Operating Pressure Range - psi:
Function:
Valve Selection:-
Materials of Construction:-
Installation:-
Standard Factory Tests:
Triple Orifice with mechanism for air/gas discharge but not airre-entry.
DN50 (2"), DN80 (3"), DN100 (4"), DN150 (6") & DN200 (8")
RGXb 1611/1621 16 (232 psi)
Min Max.16 (232 psi) 0.5 (7.2) 16 (232))
i) High volume air/gas discharge - pipeline fillingii) Pressurized air/gas discharge - pipeline filled.iii) Surge dampening - high velocity air/gas discharge,
liquid column separation & liquid oscillation.
see pages 11 & 12
see pages 32 & 34
see page 3
i) Hydrostatic test -1.5 x max. rated working pressureii) Low head leak test - 0.5 bar (7.2 psi)iii) Small orifice function test at max. rated working pressure
(minimum 1 valve in 10).
Bias
Flange with DN50 (2") Male BSP/NPT Threaded and ScrewedStuds for Alignment to BS4504, SABS1123 or ANSI B16.5 Class150 & Class 300 for DN80 (3") to DN200 (8").
RGXb 1601/1631 16 (232 psi)
Series RGXv
page: 36
information subject to change without prior notice
Note: DN50 (2") valves have DN50 (2") BSP/NPT male inlet connections as standard.
R
OVERALL DIMENSIONS & WEIGHTS
DE A
A
B
F C
GENERAL SPECIFICATIONSTHREADED 50 (2 STUDDED INLET - 80 (3") TO 200 (8") & ") EXPANDED BODY
80 3 080 RGXv 1001 & 1031 285 872 55 200 80 3 44.511 ¼ 2 / 7 /34 /13
18
78 N/A 98
100 4 100 RGXv 1001 & 1031 285 872 55 220 100 4 4411 ¼ 2 / 8 /34 /13
18
23 N/A 96.9
150 6 150 RGXv 1001 & 1031 395 1225 55 285 11 150 6 9915 / 2 /9
161
848 /2
10 N/A 218.7
200 8 200 RGXv 1001 & 1031 445 1225 55 340 200 8 12017 ½ 2 / 13 /48 /2
101
86
16 N/A 264.5
DN Model No. A B C D E F Weightmm in mm in mm in mm in mm in mm in kg lbsmm in
50 2 050 RGXv 1011 & 1021 220 862 N/A 125 5 50 2 428 / 1 / 25.523
2334 56.2
R
Series RGXv
PURCHASE SPECIFICATION
information subject to change without prior noticepage: 37
VENT -O- MAT MODEL NO.
CONSTRUCTION & DESIGN
OPERATION
Page 35 - Series RGXv - 50 (2") to 200 (8").Page 36 - Series RGXv - 50 (2") to 200 (8") (Expanded Body).
The Sewage Air Release & Vacuum Break Valve shall consist of a compact tubular all stainless steel fabricatedbody, hollow direct acting float and solid large orifice float in H.D.P.E. - stainless steel nozzle and woven dirtinhibitor screen, EPDM rubber seals and seat.
The valve shall have an integral "Anti - Surge" Orifice mechanism which shall operate automatically to limittransient pressure rise or shock induced by closure to less than 1.5 x valve rated working pressure.
The intake orifice area shall be equal to the nominal size of the valve i.e., a DN150 (6") valve shall have a DN150(6") intake orifice. Large orifice sealing shall be effected by the flat face of the control float seating against aEPDM rubber 'O' ring housed in a dovetail groove circumferentially surrounding the orifice.
Discharge of pressurized air shall be controlled by the seating & unseating of a small orifice nozzle on a naturalrubber seal affixed into the control float. The nozzle shall have a flat seating land surrounding the orifice so thatdamage to the rubber seal is prevented.The valve construction shall be proportioned with regard to material strength characteristics, so that deformation,leaking or damage of any kind does not occur by submission to twice the designed working pressure.
1. Prior to the ingress of liquid into the valve chamber, as when the pipeline is being filled, valves shallvent through the large orifice when sewage/effluent approach velocities are relative to a transientpressure rise, on valve closure, of < 1.5 x valve rated pressure.
At higher sewage/effluent approach velocities, which have a potential to induce transient pressure rises> 1.5 x valve rated pressure on valve closure, the valve shall automatically discharge air/gas through the"Anti - Surge" Orifice and reduce sewage/effluent approach velocity, so that on closure a maximumtransient pressure rise of < 1.5 x valve rated pressure is realised.
2. Valves shall not exhibit leaks or weeping of liquid past the large orifice seal at operating pressures of 0.5bar (7.2 psi) to twice rated working pressure.
3. Valves shall prevent air from entering the pipeline by the seating of the upper chamber float in the upper
chamber on the seat in the middle flange.
Connection to the valve inlet shall be facilitated by flanged ends conforming to PN10, 16 or 25 ratings ofBS4504 or SABS 1123 Standards or ANSI B16,5 Class 150 or Class 300 Standards. Flanged ends shall besupplied with the requisite number of stainless steel screwed studs inserted for alignment to the specifiedstandard. Nuts and washers shall be excluded.
Note:
All air release valves supplied shall be subjected to the following testing procedures inthe order laid down:
IMPORTANT NOTE:
1. DN250 (10") and DN300 (12") valves are available on request.
A) A high pressure strength and leak test whereby the valve is filled with water and pressurized to 1.5 x therated working pressure which shall be held for a period of 2 minutes.Any leaking, weeping or sweating shallbe reason for rejection.
B) A low head leak test whereby the valve is filled with water and pressurized to a maximum of 0.5 bar (7.2 psi)using a visible water column connected to the test rig. The valve shall be rejected if leak tightness is notmaintained for 2 minutes
C) Every tenth air release valve of the same size and pressure rating must be subjected to a small orificefunction test - "DROP TEST" - whereby the valve is filled with water, pressurized to above rated workingpressure and isolated from the test rig by closure of an isolating valve.Achamber in the test rig immediatelyprior to the isolating valve must be filled with compressed air at a pressure equal to that being maintained inthe air release valve. The isolating valve is then opened so as to allow the air to rise in the air release valvewithout the pressure dropping lower than 2 - 3 bar (29 - 44 psi) above rated working pressure of the airrelease valve. The "DROP TEST" is then carried out by slowly bleeding off the pressure through a suitablecock until rated working pressure is reached and the float drops away from the orifice to allow discharge.Failure of the air release valve to function in the manner described will be reason for rejection.
On request the manufacturer shall provide batch certificates of test compliance which shall be crossreferenced to serial numbers indelibly marked onto the identity label of each valve.
It is impossible to inject air into an incompressible liquid, air injection can only beachieved if the liquid can be displaced which implies that the pressure in the test rig must be reduced toatmospheric, and absolutely nothing is proven by discharge through the small orifice of the air release valve atatmospheric pressure. "DROPTESTING" in this manner is not acceptable.
R
Series RGXb & RGXv
ORDERING GUIDE
information subject to change without prior notice
page: 38
VALVE SERIES No.
ANTI SHOCK ORIFICE:
SPECIAL APPLICATION:BIAS AIR IN bBIAS AIR OUT v
0 5 0 R G X v 1 0 2 1VALVE TYPE:DOUBLE ACTING 1
VALVE SIZE:DN50 (2") - 0 5 0
DN80 (3") - 0 8 0
DN100 (4”) - 1 0 0
DN150 (6") - 1 5 0
DN200 (8") - 2 0 0
VALVE END CONNECTION:STUDDED FLANGED - BS4504 or SABS 1123 0THREADED - BSP MALE 1THREADED - NPT MALE 2STUDDED FLANGED - ANSI B16,5 3
VALVE PRESSURE RATING:PN10 (145 psi) 1 0
PN16 (232 psi) 1 6
R
Series RGX
Complete the form below for any additional information and fax/post to:
Vent-O-MatP.O. Box 5064Benoni SouthSouth Africa1502
Tel: (+27 11) 748 0200 Fax: (+27 11) 421 2749
E Mail: [email protected] Web site: www.ventomat.com
Company Name:
Postal Address:
Postal Code: Country:
Tel: Fax:
Contact Name: Title:
Comments:
VENT-O-MAT Series RBX Air Release & Vacuum Break Valves
VENT-O-MAT Series RC Air Release & Vacuum Break Valves
LevelDex High Performance Endline Level Control Valves
compact Stainless Steel single chamber design with integral "Anti-Shock" surge dampeningmechanism.
cast air valve for irrigation and small reticulation systems.
glass reinforced polypropylene CATT air valve for industrial, irrigation and small reticulationsystems.
end line valve with cushioned closing characteristics for level control in tanks and reservoirs.
VENT-O-MAT Series RPS Air Release & Vacuum Break Valves
VENT-O-MAT Series RBXc Air Release & Vacuum Break Valvescompact cast single chamber design with integral "Anti-Shock" surge dampening mechanismin an economical cast ductile iron construction.
Products you are interested in: