cbse i curricula x

7/27/2019 CBSE i Curricula X

1/74

ien eien e

UNIT1

CBSE-i

ClassX

PHYSICS :ELECTRIC CIRCUITS

BIOLOGY :LIFE PROCESSES

CHEMISTRY :ACIDS, BASES AND SALTS

Shiksha Kendra, 2, Community Centre, Preet Vihar,Delhi-110 092 India


2/74


3/74

CBSE-i

ClassX

PHYSICS :ELECTRIC CIRCUITS

BIOLOGY :LIFE PROCESSES

CHEMISTRY :ACIDS, BASES AND SALTS

Shiksha Kendra, 2, Community Centre, Preet Vihar, Delhi-110 092 India

ien eien e

UNIT

1


4/74

The CBSE-International is grateful for permission to reproduce

and/or translate copyright material used in this publication. The

acknowledgements have been included wherever appropriate and

sources from where the material has been taken duly mentioned. In

case anything has been missed out, the Board will be pleased to rectify

the error at the earliest possible opportunity.

All Rights of these documents are reserved. No part of this publication

may be reproduced, printed or transmitted in any form without the

prior permission of the CBSE-i. This material is meant for the use of

schools who are a part of the CBSE-International only.


5/74

PrefacePrefaceThe Curriculum initiated by Central Board of Secondary Education -International (CBSE-i) is a progressive step in making

the educational content and methodology more sensitive and responsive to the global needs. It signifies the emergence of afresh thought process in imparting a curriculum which would restore the independence of the learner to pursue thelearning process in harmony with the existing personal, social and cultural ethos.

The Central Board of Secondary Education has been providing support to the academic needs of the learners worldwide. Ithas about 11500 schools affiliated to it and over 158 schools situated in more than 23 countries. The Board has always beenconscious of the varying needs of the learners in countries abroad and has been working towards contextualizing certainelements of the learning process to the physical, geographical, social and cultural environment in which they are engaged.The International Curriculum being designed by CBSE-i, has been visualized and developed with these requirements inview.

The nucleus of the entire process of constructing the curricular structure is the learner. The objective of the curriculum is tonurture the independence of the learner, given the fact that every learner is unique. The learner has to understand,appreciate, protect and build on values, beliefs and traditional wisdom, make the necessary modifications, improvisations

and additions wherever and whenever necessary.The recent scientific and technological advances have thrown open the gateways of knowledge at an astonishing pace. Thespeed and methods of assimilating knowledge have put forth many challenges to the educators, forcing them to rethinktheir approaches for knowledge processing by their learners. In this context, it has become imperative for them toincorporate those skills which will enable the young learners to become 'life long learners'. The ability to stay current, toupgrade skills with emerging technologies, to understand the nuances involved in change management and the relevantlife skills have to be a part of the learning domains of the global learners. The CBSE-i curriculum has taken cognizance ofthese requirements.

The CBSE-i aims to carry forward the basic strength of the Indian system of education while promoting critical andcreative thinking skills, effective communication skills, interpersonal and collaborative skills along with information andmedia skills. There is an inbuilt flexibility in the curriculum, as it provides a foundation and an extension curriculum, in allsubject areas to cater to the different pace of learners.

The CBSE has introduced the CBSE-i curriculum in schools affiliated to CBSE at the international level in 2010 and is nowintroducing it to other affiliated schools who meet the requirements for introducing this curriculum. The focus of CBSE-i isto ensure that the learner is stress-free and committed to active learning. The learner would be evaluated on a continuousand comprehensive basis consequent to the mutual interactions between the teacher and the learner. There are some non-evaluative components in the curriculum which would be commented upon by the teachers and the school. The objectiveof this part or the core of the curriculum is to scaffold the learning experiences and to relate tacit knowledge with formalknowledge. This would involve trans-disciplinary linkages that would form the core of the learning process. Perspectives,SEWA (Social Empowerment through Work and Action), Life Skills and Research would be the constituents of this 'Core'.The Core skills are the most significant aspects of a learner's holistic growth and learning curve.

The International Curriculum has been designed keeping in view the foundations of the National Curricular Framework(NCF 2005) NCERT and the experience gathered by the Board over the last seven decades in imparting effective learning tomillions of learners, many of whom are now global citizens.

The Board does not interpret this development as an alternative to other curricula existing at the international level, but asan exercise in providing the much needed Indian leadership for global education at the school level. The InternationalCurriculum would evolve on its own, building on learning experiences inside the classroom over a period of time. TheBoard while addressing the issues of empowerment with the help of the schools' administering this system stronglyrecommends that practicing teachers become skillful learners on their own and also transfer their learning experiences totheir peers through the interactive platforms provided by the Board.

I profusely thank Shri G. Balasubramanian, former Director (Academics), CBSE, Ms. Abha Adams and her team and Dr.Sadhana Parashar, Head (Innovations and Research) CBSE along with other Education Officers involved in thedevelopment and implementation of this material.

The CBSE-i website has already started enabling all stakeholders to participate in this initiative through the discussionforums provided on the portal. Any further suggestions are welcome.

Vineet JoshiChairman


6/74

cknowledgementsAcknowledgements

English :

Geography:

Ms. Sarita ManujaMs. Renu Anand

Ms. Gayatri Khanna

Ms. P. Rajeshwary

Ms. Neha Sharma

Ms. Sarabjit Kaur

Ms. Ruchika Sachdev

Ms. Deepa Kapoor

Ms. Bharti DaveMs. Bhagirathi

Ms. Archana SagarMs. Manjari Rattan

Mathematics :

Political Science:

Dr. K.P. ChindaMr. J.C. Nijhawan

Ms. Rashmi Kathuria

Ms. Reemu Verma

Ms. Sharmila Bakshi

Ms. Srelekha Mukherjee

Science :

Economics:

Ms. Charu MainiMs. S. Anjum

Ms. Meenambika Menon

Ms. Novita Chopra

Ms. Neeta Rastogi

Ms. Pooja Sareen

Ms. Mridula Pant

Mr. Pankaj Bhanwani

Ms. Ambica Gulati

History :

Ms. Jayshree SrivastavaMs. M. Bose

Ms. A. Venkatachalam

Ms. Smita Bhattacharya

Material Production Groups: Classes IX-X

English :

Ms. Rachna Pandit

Ms. Neha Sharma

Ms. Sonia Jain

Ms. Dipinder Kaur

Ms. Sarita Ahuja

Science :

Dr. Meena Dhami

Mr. Saroj Kumar

Ms. Rashmi Ramsinghaney

Ms. Seema kapoor

Ms. Priyanka Sen

Dr. Kavita Khanna

Ms. Keya Gupta

Mathematics :

Political Science:

Ms. Seema Rawat

Ms. N. Vidya

Ms. Mamta Goyal

Ms. Chhavi Raheja

Ms. Kanu Chopra

Ms. Shilpi Anand

Geography:

History :

Ms. Suparna Sharma

Ms. Leela Grewal

Ms. Leeza Dutta

Ms. Kalpana Pant

Material Production Groups: Classes VI-VIII

Advisory Conceptual Framework

Ideators

Shri Vineet Joshi, Chairman, CBSE Shri G. Balasubramanian, Former Director (Acad), CBSE

Shri Shashi Bhushan, Director(Academic), CBSE Ms. Abha Adams, Consultant, Step-by-Step School, Noida

Dr. Sadhana Parashar, Head (I & R),CBSE

Ms. Aditi Misra Ms. Anuradha Sen Ms. Jaishree Srivastava Dr. Rajesh Hassija

Ms. Amita Mishra Ms. Archana Sagar Dr. Kamla Menon Ms. Rupa Chakravarty

Ms. Anita Sharma Ms. Geeta Varshney Dr. Meena Dhami Ms. Sarita Manuja

Ms. Anita Makkar Ms. Guneet Ohri Ms. Neelima Sharma Ms. Seema Rawat

Dr. Anju Srivastava Dr. Indu Khetrapal Dr. N. K. Sehgal Dr. Uma Chaudhry

Coordinators:

Dr. Sadhana Parashar, Ms. Sugandh Sharma, Dr. Srijata Das, Dr. Rashmi Sethi,Head (I and R) E O (Com) E O (Maths) E O (Science)

Shri R. P. Sharma, Consultant Ms. Ritu Narang, RO (Innovation) Ms. Sindhu Saxena, R O (Tech) Shri Al Hilal Ahmed, AEO

Ms. Seema Lakra, S O Ms. Preeti Hans, Proof Reader

Material Production Group: Classes I-V

Dr. Indu Khetarpal Ms. Rupa Chakravarty Ms. Anita Makkar Ms. Nandita Mathur

Ms. Vandana Kumar Ms. Anuradha Mathur Ms. Kalpana Mattoo Ms. Seema Chowdhary

Ms. Anju Chauhan Ms. Savinder Kaur Rooprai Ms. Monika Thakur Ms. Ruba Chakarvarty

Ms. Deepti Verma Ms. Seema Choudhary Mr. Bijo Thomas Ms. Mahua Bhattacharya

Ms. Ritu Batra Ms. Kalyani Voleti


7/74

ontentsContentsPHYSICS1. SYLLABUS COVERAGE - Physics 3

Core and Extension

2. SCOPE DOCUMENT- Physics 3

Learning Objectives

Cross Curricular Links

Suggested Activities

3. LESSON TEMPLATE-physics 5

4. Student -Teacher Support Material-Physics 8

5. Rubrics of Assessment- Physics 65

6. SYLLABUS COVERAGE - Chemistry 69

Core and Extension

7. SCOPE DOCUMENT- Chemistry 69

Learning Objectives



8. LESSON TEMPLATE- Chemistry 71

9. Student -Teacher Support Material- Chemistry 77

9. Rubrics of Assessment-Chemistry 151

(

(

(

(

(

(

chemistry


8/74

BIOLOGY

10. SYLLABUS COVERAGE - Biology 155

Core and Extension

11. SCOPE DOCUMENT- Biology 156

Learning Objectives



12. LESSON TEMPLATE- Biology 159

13. Student -Teacher Support Material- Biology 168

14. Rubrics of Assessment-Biology 258

(

(

(


9/74

Scope Document

THERMAL PHYSICS

Learning outcomes - Core

At the end of this unit, students should be able to

Explain, how solids, liquids and gases expand.

Understand the importance and significance of thermal expansion in different

practical situations.

Define specific heat capacity and specific latent heat.

Solve numericals based on specific heat capacity and specific latent heat.Understand, how heat gets transferred through solids, liquids and gases.

Differentiate between conduction, convection and radiation.

Learn about different methods of heat transfer in different situations in nature

and man made devices.

v

v

v

v

v

v

v

1SCIENCE UNIT-1 PHYSICS

hysi sPhysicsUNIT 1UNIT-1

ELECTRIC CIRCUITSELECTRIC CIRCUITS


10/74

SCIENCE UNIT-1PHYSICS


11/74

SCIENCE UNIT-1 PHYSICS

Physics

Scope Document

2

2

2

2

Learning outcomes

At the end of this unit, students should be able to

Explain an electric circuit and Draw a circuit using simple symbols for the

components of an electric circuit.

Define electric potential, potential difference and current and Understand the

relation between them.

Define and Explain resistance and derive an expression for resistance.

Explain and Verify Ohm's law

Unit 1 - ELECTRIC CIRCUITS

S

Y

L

L

A

B

U

S

2

2

2

2

2

2

Electric circuit - Drawing electric circuit using symbols

Electric Current, Electric Potential and the relation between them

Resistance and the factors on which it depends

Ohm's Law and its verification

Series and parallel Combination of resistors

Heating effect of current and its Practical Applications

Core

Syllabus Coverage

3


12/74


Understand and describe the two different types of combination of resistors -

series and parallel circuits.

Explain the heating effect of current.

Understand and explain the practical application of heating effect of current.

Solve numerical problems on resistance, combination of resistors, ohm's law

and heating effect of current and power consumption

Mathematics - Solve numerical problems

2

2

2

2

2

Cross curricular links

4


13/74

SCIENCE UNIT-1 PHYSICS

Lesson Template

Teacher's Activity Student's ActivitySteps to be

followed

Teacher may start the class by

showing a video on electricity to

build interest of the learners.

http://www.sciencekids.co.nz/v

ideos/physics/electricity.html

video.

Students will watch and

discuss the matter of the

video..

Pre content

Warming Up

Activity

5

Teacher may explain the concept

of electric potential and potential

difference by using analogies of

water flow or gravitational

potential energy and check the

understanding of the concept

using worksheets.

Students will understand the

concept and try to attempt

Worksheet 1.1 and 1.2

Content

Development

Student Teacher

Material

1. Introduction

1.1 Electric

Potential1.2 Electric

Potential

Difference

Teacher may define and explain

the making and representation of

electric circuit using activities and

examples.

Activity 2.1 and 2.2

http://www.allaboutcircuits.com

/worksheets/ohm_law.html

Students will be able to

schematically represent an

e l e c t r i c c i r c u i t u s i n g

appropriate symbols.

Worksheet 2

2. Electric Circuit


14/74

SCIENCE UNIT-1PHYSICS 6

Teacher may define and explain

the concept of flow of electric

c u r r e n t , t h e d i r e c t i o n o f

conventional current f low.

Expression and unit for electric

current.


c o n c e p t a n d a t t e m p t

worksheet 3.

3 Electric

Current

3.1 Conventional

Current

Direction

Teacher may explain the term

resistance, the effect of various

factors on resistance and its unit.

Teacher may also help the learnersd e r i v e a n e x p r e s s i o n f o r

resistance.

Activity 4

The learners can be made to

attempt an interactive activity

showing the effect of length and

area of cross section of a wire on its

resistance.

http://www.hyperstaffs.info/wo

rk/physics/child/index.html

interactive website


term will be able to solve

numerical problems.

They will try to solve

Worksheet 4

4. Journey of an

electron

4.1 Resistance and

the

factors

affecting it

4.2 Mathematical

Expression for

resistance

Teacher may explain Ohm's law

and help the learners verify it with

the help of Activity 5.

http://www.arborsci.com/Video

Links.aspx for lab activities andvideos

Teacher may explain series

connection and help the learners to

derive an expression for the

calculation of resultant resistance

of resistors connected in series

with the help of activity 6

Student will understand the

c o n c e p t t h r o u g h

experimental verification and

try to solve worksheets 5.

Students may perform the

activity and understand

s e r i e s c o n n e c t i o n , i t s

c h a r a c t e r i s t i c s a n d

calculation

5. Ohm's Law

6. Series

Combination/

circuit

6.1 Series Circuit

Calculation


15/74

SCIENCE UNIT-1 PHYSICS7

Teacher may explain parallelconnection and help the learners toderive an expression for thecalculation of resultant resistanceof resistors connected in parallelwith the help of activity 7

Students may perform theactivity and understandparallel connection, itsc h a r a c t e r i s t i c s a n dcalculation

7. ParallelCombination/circuit

7.1 Parallel circuitcalculation

T e a c h e r m a y e x p l a i n t h ecombination of series and parallelconnection with the help ofactivity 8

Teacher may show the powerpoint presentation to sum up theconcepts dealt till here.

Students may perform theactivity and understand thecombination circuit andcalculation.

8. Series andParallel

Circuit

8.1 Series parallelCalculation

Teacher may explain the heatingeffect of current, Joules law ofheating and practical applicationof heating effect with the help ofexamples and activity 9

Teacher may help the learners toderive an expression for power, itsuni t and to calculate theconsumption of electrical energywith the help of solved examples.

Students may perform thea c t i v i t y a n d d e r i v eexpression for heat energy.

Students may understand theconcept of electric power andconsumption of electricalenergy.

9. Heating Effectof Current

9.1 Application ofheating effectof current

10. Electric Power

10.1 Consumptionof electricalenergy

Teacher may sum up the concepts

dealt during the teaching learningand assess the understanding ofthe concepts through revisionassignments.

For worksheetswww.physicsclassroom.com

Teacher may ask the learners to dothe given projects individually orin groups

Students may a t tempt

Revision Worksheets 1, 2 and3.

S t u d e n t s w i l l d o t h esuggested projects.

Post Content

RevisionWorksheet

Project


16/74


Learning Objective:

Student-Teacher Material

The student may see the video and get interested in Electricity and terms and phenomena

related to it.

The teacher may show the video in the link provided here to introduce the concept of

electricity and generate an interest in the learner to study the concept.

http://www.sciencekids.co.nz/videos/physics/electricity.html video.

We already know that objects like a glass rod rubbed with silk, get electrically

charged. Such electrically charged objects show some very interesting properties that

are not shown by an uncharged objects. However, the charges on such objects are

static charges, that is, they do not move.

When charges are in motion, they are said to constitute an 'electric current'. A steady

continuous current, however, flows only when the charges move in a regular,systematic, orderly and cyclic way.

1. Introduction

8

Warm up Activity

conventionalcurrentelectrons


17/74


It was (later on) recognised that the (basic) charges that move in a current carrying

metallic wire are the negatively charged electrons. These electrons are present withinthe atoms of all the elements. In a metal, some of these often get detached from their

parent atoms. These 'free electrons' then move and roam about within the volume of

the metal. The free electrons when moving about in a metal (themselves), however,

move about in a completely random and chaotic manner. The number of electrons

moving in any one direction equals their number moving in the (exactly) opposite

direction. We therefore, need some 'external agent' that can force these electrons to

move in an orderly systematic way, within the metal .One of the simplest of such

external agents, is the familiar and well known, 'electric cell'. The cell has a potential

difference associated with it. It is this characteristic of the cell that makes it 'an agent'

that can cause an electric current to flow through a wire.

Let us, therefore understand the meaning of the terms ' electric potential' and

'potential difference'.

1.1 Electric Potential

The concept of electric potential is closely linked to that of the

electric field. Any charge, placed within an electric field,

experiences a force. Hence bringing that charge to that pointagainst the force, requires work. The electric potential at any

point is defined as the energy required to bring a unit [test]

charge from an infinite distance slowly to that point. It is

usually measured in volts. One volt is the potential at a point if

one joule of work is expended to bring a charge of one

coulomb from infinity to that point.

Electric potential is a scalar quantity, that is, it has only

magnitude but not a direction. We can view it as analogous toheight: just as a released object will fall through a difference in

heights caused by a gravitational field, so a charge will 'fall 'from a point at a

higher potential to one at a lower potential.

It was reasoned that the movement of a positive test charge within an electric

field is accompanied by changes in potential energy. We know that Potential

energy in a gravitational field is the stored energy of position of an object and it


18/74


is related to the location of the object within a field. When we introduce the

concept of electric potential we can relate this concept to the potential energy ofa positive test charge at various locations within an electric field.

While electric potential energy has a dependency upon the charge of the object

experiencing the electric field, electric potential is purely location dependent.

Electric potential is the potential energy per charge.

The concept of electric potential is closely linked to that of the electric field. Any

charge, placed within an electric field, experiences a force. Hence bringing that

charge to that point against the force, requires work. The electric potential at any

point is defined as the energy required to bring a unit [test] charge from an

infinite distance slowly to that point. It is usually measured in volts. One volt is

the potential at a point if one joule of work is expended to bring a charge of one

coulomb from infinity to that point.

Electric potential is a scalar quantity, that is, it has only magnitude but not a

direction. We can view it as analogous to height: just as a released object will fall

through a difference in heights caused by a gravitational field, so a charge will

'fall 'from a point at a higher potential to one at a lower potential.

It was reasoned that the movement of a positive test charge within an electric

field is accompanied by changes in potential energy. We know that Potential

energy in a gravitational field is the stored energy of position of an object and it

is related to the location of the object within a field. When we introduce the

concept of electric potential we can relate this concept to the potential energy of

a positive test charge at various locations within an electric field.

While electric potential energy has a dependency upon the charge of the object

experiencing the electric field, electric potential is purely location dependent.

Electric potential is the potential energy per charge.

10


19/74


Worksheet 1.1

Check Your Understanding

1. The term electric potential is defined as the amount of _____.

a. electric potential energy

b. force acting upon a charge

c. potential energy per charge

d. force per charge

2. Complete the following statement:

When work is done on a positive test charge by an external force to move it from one

location to another, potential energy _________ (increases, decreases) and electric

potential _________ (increases, decreases).

3. The following diagrams show an electric field (represented by arrows) and two points

- labeled A and B - located within the electric field. A positive test charge is shown at

point A. For each diagram, indicate whether work must be done upon the charge to

move it from point A to point B. Finally, indicate the point (A or B) with the greater

electric potential energy and the greater electric potential.

Work done on charge? Yes or No

Electric PE is greater at: A B

Electric potential is greater at: A B




B AA B


20/74


1.2 Electric Potential Difference

Electric potential is a location-dependent quantity that expresses the amount of

potential energy per unit of charge at a specified location. When a Coulomb of

charge (or any given amount of charge) possesses a relatively large quantity of

potential energy at a given location, then that location is said to be a location of

high electric potential. When we apply our concepts of potential energy andelectric potential to circuits, we will begin to refer to the difference in electric

potential between two points. It is this electric potential difference that controls

the movement of charge in electric circuits.

Consider the task of moving a positive test charge within a uniform electric field

from location A to location B as shown in the diagram at the right. In moving the

charge against the electric field from location A to location B, work will have to

be done on the charge by an external force. The work done on the charge changes

12







B

A

A

B

A volt is the unit ofelectric potential.

1 Volt = 1 Joule/Coulomb

B AE


21/74


its potential energy to a higher value; and the amount of work that is done is

equal to the change in the potential energy. As a result of this change in potentialenergy, there is also a difference in electric potential between locations A and B.

This difference in electric potential is represented by the symbol ? V and is

formally referred to as the electric potential difference. We say that

The standard metric unit on electric potential difference is the volt, abbreviated

V and named in honor of Alessandra Volta. One Volt is equivalent to one Joule

per Coulomb. If the electric potential difference between two locations is 1 volt,

then one Coulomb of charge will gain 1 joule of potential energy when moved

between those two locations because electric potential difference is expressed in

units of volts, it is sometimes referred to as the voltage.

With a clear understanding of electric potential difference, the role of an

electrochemical cell or collection of cells (i.e., a battery) in a simple circuit can be

correctly understood. The cells simply supply the energy to do work upon the

charge to move it from the negative terminal to the positive terminal. By

providing energy to the charge, the cell is capable of maintaining an electric

potential difference across the two ends of the external circuit. Once the charge

has reached the high potential terminal, it will naturally flow through the wires

to the low potential terminal in a battery-powered electric circuit, the cells serve

the role of a charge pump and supply energy to the charge to lift it back from the

low potential position through the cell to the high potential position.

As a positive test charge moves through the external circuit, it can pass through a

variety of types of circuit elements. Each circuit element serves as an energy-

transforming device. Light bulbs, motors, and heating elements (such as in

V = V - V =B AWork

Charge=

? PE

Charge

+

12 Volts

DALow

PotentialHigh

Potential

B C +

D Cell

Role of the Cell : Supplies the energy Pumps the charge from

to + terminal Maintains a V across


22/74


toasters and hair dryers) are examples of energy-transforming devices. In each

of these devices, the electrical potential energy of the charge is transformed intoother useful (and non-useful) forms. For instance, in a light bulb, the electric

potential energy of the charge is transformed into light energy (a useful form)

and thermal energy (a non-useful form). The loss in electric potential while

passing through a circuit element is often referred to as a voltage drop. By the

time that the positive test charge has returned to the negative terminal, it is at 0

volts and is ready to be re-energized and pumped back up to the high voltage,

positive terminal.

1. Moving an electron within an electric field would change the ____ the electron.

a. mass of b. amount of charge on

c. potential energy of d. weight of

2. If an electrical circuit were analogous to a water circuit at a water park, then the

battery voltage would be comparable to _____.

a. the rate at which water flows through the circuit

b. the speed at which water flows through the circuit

c. the distance that water flows through the circuit

d. the water pressure between the top and bottom of the circuit

3. If the electrical circuit in your Walkman were analogous to a water circuit at a water

park, then the battery would be comparable to _____.

a. the obstacles that stand in the path of the moving water

b. the pump that moves water from the ground to the elevated positions

c. the pipes through which water flows

d. the distance that water flows through the circuit

Worksheet 1.2


14


23/74


4. Which of the following is true about the electrical circuit in your flashlight?

a. Charge moves around the circuit very fast - nearly as fast as the speed of light.

b. The battery generates the charge (electrons) that moves through the wires

c. The charge becomes used up as it passes through the light bulb.

d. The battery supplies energy that raises charge from low to high voltage.

5. If a battery provides a high voltage, it can ____.

a. do a lot of work over the course of its lifetime

b. do a lot of work on each charge it encounters

c. push a lot of charge through a circuit

d. last a long time

The diagram below at the right shows a light bulb connected by wires to the + and -

terminals of a car battery. Use the diagram in answering the next four questions.

6. Compared to point D, point A is _____ electric potential.

a. 12 V higher in

b. 12 V lower in

c. exactly the same

7. The electric potential energy of a charge is zero at point _____.

8. Energy is required to force a positive test charge to move ___.

a. through the wire from point A to point B

b. through the light bulb from point B to point C

c. through the wire from point C to point D

d. through the battery from point D to point A

9. The energy required to move +2 C of charge between points D and A is ____ J.

a. 0.167 b. 2.0 c. 6.0 d. 12 e. 24

+ 12 Volts

DA

B C


24/74


10. The following circuit consists of a dry cell and a light bulb. Use >, , < or =)

V _____VC D(>, < or =)

V _____VB D(>, < or =)

Battery

+ + + + + ++ + + + + +

E

High Potential

Low Potential


25/74


2. Electric Circuit

Activity 2.1

Electric potential is the amount of electric potential energy per unit of charge that

would be possessed by a charged object if placed within an electric field at a given

location. Electric potential difference is simply the difference in electric potential

between two different locations within an electric field.

Let us now understand the meaning of an electric circuit. In an electric circuit, charges

must continually flow through a complete loop, returning to their original position

and cycling through again. If there were a means of moving positive charge from the

negative plate back up onto the positive plate, then the movement of positive charge

downward through the charge pipe (i.e., the wire) would occur continuously. In such

a case, a circuit or loop would be established.

Students will be able to

Illustrate the necessity of a closed conducting path for the flow of charges.

Observe the effect of connecting and disconnecting a wire.

The teacher may provide the students with

1. a battery pack(two to three cells)

2. a torch bulb

3. a few pieces of connecting wires

4. a switch

The students may be asked to connect the components and observe that when all

connections are made to the battery pack, the light bulb lights. In fact, the lighting of

the bulb occurs immediately after the final connection is made. There is no

perceivable time delay between when the last connection is made and when the light

bulb is perceived to light up.

The fact that the light bulb lights and remains lit is evidence that charge is flowing

through the light bulb filament and that an electric circuit has been established. A

Learning Objectives:


26/74


circuit is simply a closed loop through which charges can continuously move. To

demonstrate that charges are not only moving through the light bulb filament but alsothrough the wires connecting the battery pack and the light bulb, a variation on the

above activity is made. A compass is placed beneath the wire at any location such that

its needle is placed in alignment with the wire. Once the final connection is made to

the battery pack, the light bulb lights and the compass needle deflects. The needle

serves as a detector of moving charges within the wire. When it deflects, charges are

moving through the wire. And if the wire is disconnected at the battery pack, the light

bulb is no longer lit and the compass needle returns to its original orientation. When

the light bulb lights, charge is moving through the electrochemical cells of the battery,

the wires and the light bulb filaments; the compass needle detects the movement of

this charge. It can be said that there is a current - a flow of charge within the circuit.

The electric circuit demonstrated by the combination of battery, light bulb and wires

consists of two distinct parts: the internal circuit and the external circuit. The part of

the circuit containing electrochemical cells of the battery is the internal circuit. The

part of the circuit where charge is moving outside the battery pack through the wires

and the light bulb is the external circuit.

After reading this section students will be able to do the following:

Explain what circuit diagrams are used for.

Identify what the symbols in the circuit diagrams stand for.

Circuit diagrams are a pictorial way of showing circuits. Electricians and engineers

draw circuit diagrams to help them design the actual circuits. Here is an examplecircuit diagram.

ACTIVITY 2.2

2

2

CIRCUIT DIAGRAMS

18

V

A


27/74


The important thing to note on this diagram is what different symbols stand for. We

see that there are straight lines that connect each of the symbols together. These linesrepresent a wire.

represents an Ammeter.

represents a Voltmeter.

represents the resistor.

represents a switch.

represents a battery.

represents a light bulb.

1. Circuit diagrams are used to show how all the components connect together to make a

circuit.

Example 1:

Three Dry cells are placed in a battery pack to power a circuit containing three light

bulbs connected as shown. We can then draw its circuit diagram by using the

schematic symbols shown alongside.

Review

V

A

Drawing of Circuit Schematic Diagram of Circuit


28/74


Example 2:

Three D-cells are placed in a battery pack to power a circuit containing three light

bulbs.

Using the verbal description, one can acquire a mental picture of the circuit being

described. But this time, the connections of light bulbs is done in a manner such that

there is a point on the circuit where the wires branch off from each other. The

branching location is referred to as a node. Each light bulb is placed in its own

separate branch. These branch wires eventually connect to each other to form a

second node. A single wire is used to connect this second node to the negative

terminal of the battery.

1. Use circuit symbols to construct schematic diagrams for the following circuits:

a. A single cell, light bulb and switch are placed together in a circuit such that the

switch can be opened and closed to turn the light bulb on.

b. A three-pack of D-cells is placed in a circuit to power a flashlight bulb.

Worksheet 2


20

Schematic Diagram of CircuitDrawing of Circuit

c. d.


29/74


2. Use the concept of conventional current to draw an unbroken line on the schematic

diagram at the right that indicates the direction of the conventional current. Place an

arrowhead on your unbroken line.

3. If an electric circuit could be compared to a water circuit at a water park, then the ...

... battery would be analogous to the ____.

... positive terminal of the battery would be analogous to the ____.

... current would be analogous to the ____.

... charge would be analogous to the ____.

... electric potential difference would be analogous to the ____.

Choices:

A. water pressure B. volume of water flowing down slide per minute

C. water D. bottom of the slide

E. water pump F. top of the slide

4. Utilize your understanding of the requirements of an electric circuit to state whether

charge would flow through the following arrangements of cells, bulbs, wires and

switches. If there is no charge flow, then explain why not.

a. b.

Charge Flow: Yes or No? Charge Flow: Yes or No?

Explanation: Explanation:

+

+


30/74


c. d.

Charge Flow: Yes or No? Charge Flow: Yes or No?

Explanation: Explanation:

5. The diagram shows a light bulb connected to a 12-V car battery. The + and - terminals

are shown.

a. As a + charge moves through the battery from D to A, it ________ (gains, loses)

potential energy and ________ (gains, loses) electric potential. The point of

highest energy within a battery is the ______ (+, -) terminal.

b. As a + charge moves through the external circuit from A to D, it ________ (gains,

loses) potential energy and ________ (gains, loses) electric potential. The point

of highest energy within the external circuit is closest to the ______ (+, -)

terminal.

c. Use >,


31/74


to fry." Russell responds with "You didn't take high school Physics, did you? As long

as you're only touching one wire and your feet aren't touching the ground, you don'tget electrocuted." Is this a correct statement?

If the two requirements of an electric circuit are met, then charge will flow through the

external circuit. It is said that there is a current - a flow of charge. Using the word

current in this context is to simply use it to say that something is happening in the

wires - charge is moving. Yet current is a physical quantity that can be measured and

expressed numerically. As a physical quantity, current is the rate at which chargeflows past a point on a circuit. The current in a circuit can be determined if the

quantity of charge Q passing through a cross section of a wire in a time t can be

measured. The current is simply the ratio of the quantity of charge and time.

Current is a rate quantity and is expressed mathematically as

Current = I =

Note that the equation above uses the symbol I to represent the quantity current.

The standard metric unit for current is the ampere. It is often shortened to Amp and is

abbreviated by the unit symbol A. A current of 1 ampere means that there is 1

coulomb of charge passing through a cross section of a wire every 1 second.

1 ampere = 1 coulomb / 1 second

3. Electric Current

Qt

+

I

I

I

IElectric current in the external

circuit is directed from thepositive to the negative terminal.


32/74


To test your understanding, determine the current for the following two situations.

24

A 2 mm long cross section of wire is

isolated and 20 C of charge is determined

to pass through it in 40

A 1 mm long cross section of wire is

isolated and 2 C of charge is determined

to pass through it in 0.5

3.1 Conventional Current Direction

The particles that carry charge through wires in a circuit are mobile electrons. The

electric field direction within a circuit is by definition the direction that positive test

charges are pushed. Thus, these negatively charged electrons move in the direction

opposite the electric field. But while electrons are the charge carriers in metal wires,

the charge carriers in other circuits can be positive charges, negative charges or both.

In fact, the charge carriers in semiconductors, street lamps and fluorescent lamps are

simultaneously both positive and negative charges traveling in opposite directions.

Ben Franklin, who conducted extensive scientific studies in both static and current

electricity, envisioned positive charges as the carriers of charge. As such, an early

convention for the direction of an electric current was established to be in the

direction that positive charges would move. The convention has stuck and is still used

today. The direction of an electric current is by convention the direction in which a

positive charge would move. Thus, the current in the external circuit is directed away

from the positive terminal and toward the negative terminal of the battery. Electrons

would actually move through the wires in the opposite direction.

2mm

20 C 20 C40 s

1mm

2 C 2 C0.5 s

I = _____ ampere I = _____ ampere


33/74


Worksheet 3


1. A current is said to exist whenever _____.

a. a wire is charged

b. a battery is present

c. electric charges are unbalanced

d. electric charges move in a loop

2. Current has a direction. By convention, current is in the direction that ___.

a. + charges move

b. - electrons move

c. + electrons move

d zero charge neutrons move

3. The diagram below depicts a conducting wire. Two cross-sectional areas are located50 cm apart. Every 2.0 seconds, 10 C of charge flow through each of these areas. The

current in this wire is ____ A.

a. 0.10 b. 0.25 c. 0.50

d. 1.0 e. 5.0 f. 20g. 10

h. 40 i. none of these

50cm

10 C 10 C2s


34/74


4. Look at the diagram below and complete the following statements:

a. When a current of one ampere How through the bulb located between A and B,there would be a flow of charge at the rate of _______ coulomb per second

through this bulb.

b. When a charge of 8 C flows past any point along the circuit in 2 seconds, the

current is ________ A.

c. If 5 C of charge flow past point A (diagram at right) in 10 seconds, then the

current is _________ A.

d. If the current at point D is 2.0 A, then _______ C of charge flow past point D in 10seconds.

e. If 12 C of charge flow past point A in 3 seconds, then 8 C of charge will flow past

point E in ________ seconds.

f. True or False:

The current at point E is considerably less than the current at point A since

charge is being used up in the light bulbs.

An electrochemical cell supplies energy to move a

charge from its low energy, low potential terminal to the

high energy, high potential terminal. In this sense, the

cell supplies the energy to establish an electric potential

difference across the two ends of the external circuit.

Charge will then flow through the external circuit in the

4. Journey of a Typical Electron


35/74


same manner that water will flow from an elevated position to a low position. It is the

difference in potential that causes this flow.

In the wires of electric circuits, an electron is the

actual charge carrier. An electron's path through

the external circuit is far from being a straight path.

An electron's journey through a circuit can be

described as a zigzag path that results from

countless collisions with the atoms of the

conducting wire. Each collision results in the alteration of the path, thus leading to a

zigzag type motion. While the electric potential difference across the two ends of acircuit encourages the flow of charge, it is the collisions of charge carriers with atoms

of the wire that discourages the flow of charge. Different types of atoms offer a

different degree of hindrance to the flow of the charge carriers that pass through it.

In all cases, the collisions of charge carriers in an electric circuit with the conducting

elements of that circuit result in a loss of energy. While most the electrical energy

possessed by a charge carrier is lost when it passes through an electrical device (often

referred to as the load), even the wires of the circuit themselves act to remove energy

from a charge. It is because of this energy loss in the load and in the wires themselvesthat the electric potential of a charge carrier is decreased as it traverses the external

circuit. The electric energy supplied by the electrochemical cells becomes entirely

used up in the external circuit.

In an electric circuit with several electrical devices, there may be multiple stepwise

losses of electric potential as the charge traverses the circuit. Regardless of the way in

which the devices are wired, the total loss of electric potential of a single charge as it

passes through the external circuit is equal to the gain in electric potential that it

experiences in the battery.

The journey of an electron through an external circuit involves a long and slow zigzag

path that is characterized by several successive losses in electric potential. Each loss of

potential is referred to as a voltage drop. Accompanying this voltage drop is a voltage

boost occurring within the internal circuit - for instance, within the electrochemical

cell.


36/74


4.1 Resistance

An electron traveling through the wires and loads of the external circuit encounters

resistance. Resistance is the hindrance to the flow of charge. For an electron, the

journey from terminal to terminal is not a direct route. Rather, it is a zigzag path that

results from countless collisions with fixed atoms within the conducting material.

The electrons encounter resistance - a hindrance to their movement. While the electric

potential difference established between the two terminals encourages the

movement of charge, it is resistance that discourages it. The rate at which charge flows

from terminal to terminal is the result of the combined affect of these two quantities.

Variables Affecting Electrical Resistance

The flow of charge through wires is often compared to the flow of water through

pipes. The resistance to the flow of charge in an electric circuit is analogous to the

frictional affects between water and the pipe surfaces as well as the resistance offered

by obstacles that are present in its path. It is this resistance that hinders the water flow

and reduces both its flow rate and its drift speed. Like the resistance to water flow, the

total amount of resistance to charge flow within a wire of an electric circuit is affected

by some clearly identifiable variables.

Learners can perform this activity on their own to understand the effect of length and

area of cross section of a wire on its resistance.

http://www.hyperstaffs.info/work/physics/child/index.html interactive website

First, the total length of the wires will affect the amount of resistance. The longer the

wire, the more will be its resistance. There is a direct relationship between the amount

of resistance encountered by charge and the length of wire it must traverse. After all, ifresistance occurs as the result of collisions between charge carriers and the atoms of

the wire, then there is likely to be more collisions in a longer wire. More collisions

mean more resistance.

Second, the cross-sectional area of the wires will affect the amount of resistance.

Wider wires have a greater cross-sectional area. Water will flow through a wider pipe

at a higher rate than it will flow through a narrow pipe. This can be attributed to the

lower amount of resistance that is present in the wider pipe

Activity 4 [on the Net]

28


37/74


A third variable that is known to affect the resistance to charge flow is the material

that a wire is made of. Not all materials are created equal in terms of their conductiveability. Some materials are better conductors than others and offer less resistance to

the flow of charge. Silver is one of the best conductors but is never used in wires of

household circuits due to its cost. Copper and aluminum are among the least

expensive materials with suitable conducting ability to permit their use in wires of

household circuits. The conducting ability of a material is often indicated by its

resistivity. The resistivity of a material is dependent upon the material's electronic

structure and its temperature. For most (but not all) materials, resistivity increases

with increasing temperature. The table below lists resistivity values for various

materials at temperatures of 20 degrees Celsius.

-8Silver 1.59 x 10

-8Copper 1.7 x 10

-8Gold 2.4 x 10

-8Aluminum 2.8 x 10

-8Tungsten 5.6 x 10

-8Iron 10 x 10

-8Platinum 11 x 10

-8Lead 22 x 10

-8Nichrome 150 x 10

5Carbon 3.5 x 10

7 11Polystyrene 10 - 10

8 9Polyethylene 10 - 10

10 14Glass 10 - 10

13Hard Rubber 10

Material Resistivity

(ohmmeter)


38/74


4.2 Mathematical Expression of Resistance


Resistance is a numerical quantity that can be measured and expressed

mathematically. The standard metric unit for resistance is the ohm, represented by

the Greek letter omega -. An electrical device having a resistance of 5 ohms would

be represented as R = 5. The equation representing the dependency of the resistance

(R) of a wire shaped conductor upon the variables that affect it is

where L represents the length of the wire (in meters), A represents the cross-sectional

area of the wire (in meters2), and represents the resistivity of the material (inohmometer). This equation shows that the resistance of a wire is directly proportional

to the length of the wire and inversely proportional to the cross-sectional area of the

wire. Knowing the length, cross-sectional area and the material that a wire is made of

(and thus, its resistivity) one can determine the resistance of the wire.

1. Household circuits are often wired with two different thickness of wires: 12-gauge

and 14-gauge. The 12-gauge wire has a diameter of 2.1 mm while the 14-gauge wire

has a diameter of 1.8 mm. Thus, 12-gauge wire has a wider cross section than 14-

gauge wire. A 20-Amp circuit used for wall receptacles should be wired using 12-

gauge wire and a 15-Amp circuit used for lighting and fan circuits should be wired

using 14-gauge wire. Explain the physics behind such an electrical code.

2. Based on the information stated in the above question, explain the risk involved in

using 14-gauge wire in a circuit that will be used to power an 16-ampere power saw.

3. Determine the resistance of a 1 Km length of 12-gauge copper wire of diameter 2.1

mm.

4. Two wires - A and B - with circular cross-sections have identical lengths and are made

of the same material. Yet, wire A has four times the resistance of wire B. How many

times greater is the diameter of wire B than wire A?

Worksheet 4

30

R = p LA


39/74


Student Teacher Material

5. Ohm's Law

Ohm's Law gives the relation between the potential difference across the two

terminals of a conductor and the current flowing through it.

It states that the potential difference across the two terminals of a conductor is directly

proportional to the current passing through it.

V I

V = RI where R(resistance) is the proportionality constant

A very well known equation which pervades the study of electric circuits, is the

equation

V = I R

In words, the electric potential difference between two points on a circuit (V) is

equivalent to the product of the current between those two points (I) and the total

resistance of all electrical devices present between those two points (R). Often

referred to as the Ohm's law equation, this equation is a powerful predictor of the

relationship between potential difference, current and resistance.

Ohm's Law as a Predictor of Current

The Ohm's law equation can be rearranged and expressed as

This equation can be used for, calculating the current if the electric potential

difference and the resistance are known. This equation indicates the two variables

that would affect the amount of current in a circuit. The current in a circuit is directly

proportional to the electric potential difference impressed across its ends and

inversely proportional to the total resistance offered by the external circuit. The

greater the battery voltage (i.e., electric potential difference), the greater the current.

And the greater the resistance, the less the current. The table below illustrates this

relationship both qualitatively and quantitatively for several circuits with varying

battery voltages and resistances.

I = VR


40/74


Circuit Battery Total Current

Diagram Voltage Resistance (Amps)

(V) (? )

1. 1.5 V 3 ? 0.50 Amp

2. 3.0 V 3 ? 1 Amp

3. 1.5 V 6 ? 0.25 Amp

4. 3.0 V 6 ? 0.5 Amp

Because the current in a circuit is affected by the resistance, resistors are often used in

the circuits of electrical appliances to affect the amount of current that is present in itsvarious components. By increasing or decreasing the amount of resistance in a

particular branch of the circuit, one can increase or decrease the amount of current in

that branch. Kitchen appliances such as electric mixers and light dimmer switches

operate by altering the current at the load by increasing or decreasing the resistance of

the circuit.

The diagram below depicts a couple of circuits containing a voltage source (battery

pack), a resistor (light bulb) and an ammeter (for measuring current). In which circuit

does the light bulb have the greatest resistance?


41/74


Ohm's law can be verified in the laboratory using a resistor, a battery pack, an

ammeter, and a voltmeter. An ammeter is a device used to measure the current at agiven location. A voltmeter is a device that can be touched to two points on a circuit to

determine the electric potential difference across those points. By altering the number

of cells in the battery pack, the electric potential difference across the external circuit

can be varied. The voltmeter can be used to determine this potential difference and

the ammeter can be used to determine the current associated with this ?V. The process

can be repeated several times to yield a set of I- ?V data. A plot of I versus ?V is seen to

be a straight line with a slope that is equivalent to the reciprocal of the resistance of the

resistor. Ohm's law equation thus gets checked.

Verification of Ohm's Law

The learners will be able

to perform an experiment to verify Ohm's Law

to practice constructing electric circuits

to practice using an ammeter and a voltmeter

The teacher may give the instructions before hand.

In the lab, you will construct a simple circuit using a single known resistance, R. Then you

will use an ammeter to measure the current, I, through the resistance and a voltmeter to

measure the potential difference, V, across the resistance. With this data, you can check the

validity of Ohm's Law (V = IR) in the circuit.

1.5 or 2 V power supply switch resistor

0-1 A ammeter 0-3 V voltmeter connecting wires

Activity 5

2

2

2

Learning Objectives:

Discussion:

Equipment:


42/74


Procedure:

IMPORTANT: In this lab you will use ONLY the "COMMON" and "1.5 or 2 V DC"

terminals on the power supply. Connecting the circuit to any other terminals will certainly

result in destruction of equipment and might well be risky for the user.

Set up the circuit shown in the diagram shown using the resistor of known value.

a. Screw one end of the resistor to the 1.5/2 VDC terminal of the power supply.

b. Using one of the connecting wires, connect the other end of the resistor to the red

terminal of the ammeter.

c. Be sure that the switch is open.

d. Using another wire, connect the black terminal of the ammeter to either side of

the switch. Notice that when the switch is closed, current will flow through the

resistor, the ammeter, and the switch in this circuit.

e. Connect the other switch terminal to the COMMON terminal on the power

supply using a wire.

f. Connect a wire from the red terminal of the voltmeter to the 1.5/2 VDC terminal

of the power supply.

g. Connect a wire from the black terminal of the voltmeter to the red terminal of the

ammeter.

After the completion of the circuit carefully read the voltage across the resistor and the

current through the resistor and record the readings in a tabular form. Repeat the

experiment for different values of voltage.

34

1.5 or 2 V DC


43/74


Results:


For each set of values of the voltage drop and the current, the calculated resistance remains

constant, hence verifying Ohm's law.

1. Which of the following will cause the current through an electrical circuit to decrease?

Choose all that apply.

a. decrease the voltage

b. decrease the resistance

c. increase the voltage

d. increase the resistance

2. A certain electrical circuit contains a battery with three cells, wires and a light bulb.

Which of the following would cause the bulb to shine less brightly? Choose all that

apply.

a. increase the voltage of the battery by adding another cell

b. decrease the voltage of the battery ( by removing a cell)

c. decrease the resistance of the circuit

d. increase the resistance of the circuit

3. You have likely been warned to avoid contact with electrical appliances or even

electrical outlets when your hands are wet. Such contact is more dangerous whenyour hands are wet (vs. dry) because wet hands cause ____.

a. the voltage of the circuit to be higher

b. the voltage of the circuit to be lower

c. your resistance to be higher

d. your resistance to be lower

Worksheet 5


44/74


4. If the resistance of a circuit were increased three times, then the current through the

circuit would be ____.

a. one-third as much

b. three times as much

c. unchanged

5. If the voltage across a circuit is increased four times, then the current through the

circuit would be ____.

a. one-fourth as much

b. four times as much

c. unchanged

6. A circuit is wired with a power supply, a resistor and an ammeter (for measuring

current). The ammeter reads a current of 24 mA (milliamps). Determine the new

current if the voltage of the power supply was ...

a. ... increased by a factor of 2 and the resistance was held constant.

b. ... increased by a factor of 3 and the resistance was held constant.

c. ... decreased by a factor of 2 and the resistance was held constant.

d. ... held constant and the resistance was increased by a factor of 2.

e. ... held constant and the resistance was increased by a factor of 4.

f. ... held constant and the resistance was decreased by a factor of 2.

g. ... increased by a factor of 2 and the resistance was increased by a factor of 2.

h. ... increased by a factor of 3 and the resistance was decreased by a factor of 2.

i. ... decreased by a factor of 2 and the resistance was increased by a factor of 2.

7. Use Ohm's law equation to provide numerical answers to the following questions:

a. An electrical device with a resistance of 3.0 ? will allow a current of 4.0 amps to

flow through it if a voltage drop of ________ Volts is impressed across the

device.

36


45/74


b. When a voltage of 120 V is maintained across an electric heater, a current of 10.0

amps will flow through the heater if the resistance is ________ ? .

c. A flashlight that is powered by 3 Volts and uses a bulb with a resistance of 60 ?

will have a current of ________ Amps.

8. Use Ohm's law equation to determine the missing values in the following circuits.

9. Refer to question 8 above. In the circuits of diagrams A and B, what method was usedto control the current in the circuits? And in the circuits of diagrams C and D, what

method was used to control the current in the circuits?


46/74


6. THE SERIES CIRCUIT

ACTIVITY 6

2

2

2

After reading this section, students will be able to do the following:

Define a series circuit, and list the components needed to make it.

Construct a simple and complex series circuit.

Define what a load is.

Try building this simple series circuit

The circuit we see above is something called a series circuit. This is called a series circuit

because there is only one path for the electrons to take between any two points in thiscircuit. In other words, the components, which are the battery, the switch, the ammeter,

and light, are all in "series" with each other.

Notice that when we close the switch to complete the electrical circuit, the electrons start

moving and the ammeter indicates that there is current flowing in this circuit. Also notice

that the light bulb begins to glow.

The light bulb is considered a load in this circuit. We might think of a load as anything that

is using the energy that is being delivered by the electric current in a circuit. It could be

anything from a light bulb to a computer to a washing machine and so on.

Try building a series circuit with resistors

Let's build another series circuit, but this time we will use some resistors instead of a light

bulb. Resistors are components that are used to control that amount of current flowing in a

circuit. If there are no resistors to control the flow of electrical current, too much current

may flow through the circuit and damage its components or wires.

Load defined

38


47/74


Characteristics of 'SERIES CIRCUITS

Review

6.1 SERIES CIRCUIT CALCULATIONS

In a Series Circuit the charge carriers [electrons] have only one path to flow. Hence the

electrons must go through each component to complete the flow. When the loads are

placed in series, we would observe the following

1. An open in the circuit will disable the entire circuit.

2. The voltage gets divides (shared) between the loads.

3. The current flow is the same throughout the circuit.

4. The resistance of each load can be different.

1. When all the components are in line with each other and the wires, a series circuit is

formed.

2. A load is any device in a circuit that is using the energy that the electron current is

delivering to it.

If, for example, two or more lamps

(resistances R and R , etc.) are connected in a1 2

circuit as follows, there is only one route that

the current can take. This type of connection

is called a series connection. The value of

current I is always the same at any point in a

series circuit.

The combined resistance RO in this circuit is

equal to the sum of individual resistance R1


48/74


and R . In other words: The total resistance(RO) is equal to the sum of all resistances2

(R + R + R + .......)1 2 3

R = R + R0 1 2

Therefore, the strength of current (I) flowing in the circuit can be found as follows:

Resistance R0 (a combination of resistances R1 and R2, which are connected in seriesin the circuit as illustrated) and current I flowing in this circuit can be determined as

follows:

40


49/74


7. THE PARALLEL CIRCUIT

ACTIVITY 7

2

2

2


Define a parallel circuit and explain how it compares to a series circuit.

Construct a parallel circuit.

Explain what a voltmeter does and how it is different from an ammeter.

Like the series circuit, parallel circuits also contain a voltage (current) source as well as

wires and other components. The main difference between a series circuit and a parallel

circuit is in the way the components are connected. In a parallel circuit the electricity has

several paths that it can travel.

Try building this simple parallel circuit

Notice that when you closed the switch, the electrons flowed through both loads at the

same time. In our series circuit, all the electrons flowed through all the components in

order. With the parallel circuit, some electrons go through one load and some go through

the other load, all at the same time. At point A, the total current splits up and takes different

paths before the circuit joins back together again at point B.

A parallel circuit exists whenever two or more components are connected between the

same two points. Those two points in this circuit are points A and B. Both resistors connect

to both points A and B.

Each parallel path is called a branch of the parallel circuit. We will now try building this

parallel circuit, including a voltmeter


50/74


The parallel circuit shown here, contains 3 branches (two resistors and a voltmeter), which

means the electron current goes through all three branches at the same time. We put a

voltmeter on this second circuit to show an important fact. In the last 4 circuits we made, we

included an ammeter into them. Ammeters must always be placed in series in a circuit,

otherwise they will not work. The voltmeter we added in the last circuit has a different

requirement in order to work. Voltmeters must be placed in parallel with the circuit in

order to work. This is because voltage meters measure the difference in potential from one

point to another.

A Parallel Circuit has multiple paths or branches to ground. Therefore:

1. In the event of an open in the circuit in one of the branches, current will continue toflow through the remaining.

2. Each branch receives the same source voltage.

3. Current flow through each branch can be different.

4. The resistance of each branch can be different.

CHARACTERISTICS OF PARALLEL CIRCUITS

42


51/74


Review

7.1 PARALLEL CIRCUIT CALCULATION

1. When some of the components are connected parallel with each other, they form a

parallel circuit.

2. A voltmeter must be wired in parallel in a circuit in order to measure the difference in

potential from one point to another.

In parallel connection, two or more resistances (R1, R2, etc.) are connected in a circuit

as follows, with one end of each resistance connected to the high (positive) side of the

circuit, and one end connected to the low (negative) side. Full battery voltage is

applied to all resistances within a circuit having a parallel connection.

Resistance R (a combination of resistances R1 and R2) in a parallel connection can be0

determined as follows:


52/74


From the above, the total current I flowing in this circuit can be determined from

Ohm's law as follows:

The total current I is also equal to the sum of currents I1 and I2 flowing through

individual resistances R1 and R2

I = I + I1 2

Since battery voltage V is applied equally to all resistances, the strength of currents I1

and I2 can be determined from Ohm's law as follows:

Resistance R (a combination of resistances R1 and R2, which are connected in parallel0

in the circuit as shown below), the total current I flowing in the circuit, and currents I1

andI2 flowing through resistances R1 and R2, can be determined respectively as

follows:

44


53/74


8. THE SERIES/PARALLEL CIRCUIT

ACTIVITY 8

2

2


Explain what a series/parallel circuit is and what components are needed to

complete it.

Construct a series/parallel circuit.

When we have a circuit in which some of the components are in series and others are in

parallel, we have a series/parallel circuit.

Try building a series/parallel circuit


54/74


Notice in this series/parallel circuit that the resistors R1, the switch, the battery, and the

ammeter are in series with each other while resistors R2 and R3 are in parallel with eachother. We might also say that the R2/R3 combination is in series with the rest of the

components in this circuit.

By applying Ohm's law, to a given series or parallel or a combination of the two circuits, we

can calculate the current flowing at any point in such circuits.

The combined resistance R02 in this series-parallel connection can be determined in the

following order:

a. Determine combined resistance R01, which is a combination of resistances R2and R3 connected in parallel.

b. Then, determine resistance R02, which is a combination of resistance R1 and

combined resistance R01 connected in series.

Total current I flowing in the circuit can be determined from Ohm's law as follows:

The voltage applied to R2 and R3 can be found by the following formula:

Currents I1, I2 and I flowing through resistances R1, R2 and R3 in the series-parallel

connection, as shown below, can be determined as follows:

8.1 SERIES PARALLEL CALCULATIONS

46


55/74


NOTE: The Powerpoint Presentation attached here can be used for recapitulating the

concepts dealt till this section of the chapter.


56/74


9. Heating effect of current

ACTIVITY 9

2

2

2

2

2

2

Class experiment

Apparatus and materials

Safety

Procedure

Illustrates two ideas: electric current causes heating effect; temperature affects the

resistance of a wire.

For each student group:

Cells, 1.5 V, with holders, 3

Lamp with holder

Crocodile clips, 2

Ammeter (0 - 1 amp), DC

Leads, 4 mm, 5

Eureka wire 34 SWG, 15 cm length

Modern dry cell construction uses a steel can connected to the positive (raised) contact. The

negative connection is the centre of the base with an annular ring of insulator between it

and the can

48


57/74


a Set up a series circuit of three cells and a lamp. Include two crocodile clips in the

circuit.b Wind the length of bare Eureka wire into a coil (using, say, a pencil). Clamp the ends

of the wire into the two crocodile clips. (Make sure that the turns of wire do not touch

each other.)

c Stand back! Carefully, hold your hand above the wire coil. Can you feel hot air rising?

1 When an electric current passes through a metal, it warms up. The open coil of wire

will be warm to the touch. Blowing on the wire will reduce its temperature and thelamp will glow brighter. Try using an electronics freezer spray to reduce the

temperature of the coil even more and the lamp will glow brighter still.

2 It is important that the coils must not touch each other, or the coil will become a short

circuit.

3 This experiment can be demonstrated in order to explain how a filament lamp works.

The filament is just a short piece of wire which gets so hot that it glows red for low

currents, becoming whiter as the current increases staying within its permitted [safe]

limits, of course.4 Careful and observant students are likely to have noticed that when a circuit

consisting of a cell, a lamp and an ammeter is connected, the current is momentarily

greater when the connection is made, and then the current settles down to a steady

lower value. This is because the resistance of the cold wire is less than the resistance of

the hot wire.

Heating effect of electricity is one of the widely used effects in the world. When

electric current is passed through a conductor, it generates heat due to the resistance it

offers to the current flow. The work done in overcoming the resistance is generated as

heat. This is studied by James Prescott Joule and he enunciated various factors that

affect the heat generated. The heat produced by a heating element is directly

proportional to the square of the electric current (I) passing through the conductor,

directly proportional to the resistance (R) of the conductor, time (t) for which current

passes through the conductor. It is given by the expression H = I2Rt and is well known

as Joule's Law.

Teaching notes

9.1 Applications of 'Heating Effect of Current'


58/74


Applications of the heating effect of electric current include appliances like electric

immersion water heater, electric iron box, etc. All of these have a heating element in it.Heating elements are generally made of specific alloys like, nichrome, manganin,

constantan etc. A good heating element has high resistivity and high melting point.

An electric fuse is an example for the application of heating effect of electric current.

The rating of 3 A of an electric fuse implies the maximum current it can sustain is three

ampere.

Joules law of Heating

When some potential difference V is applied across a resistance R then the work done

by the electric field on charge q to flow through the circuit in time t will be

This work appears as thermal energy in the resistor.

Heat produced by the resistance R is quite often expressed in Calorie. Since 1 calorie =

4.2 J we have

The rate at which electrical energy is dissipated into other forms of energy is called

electric power i.e.

Units: It's S.I. unit is joule/sec or watt

Bigger S.I. units are KW, MW and horse power [HP], remember that 1 HP = 746 Watt

Rating values

On electrical appliances (Bulbs, Heater, Geyser etc). wattage, voltage, etc. are

printed. These are called its rating values. If suppose we have a bulb of 40 W, 220 V

then rated power (PR) = 40 W while rated voltage (VR) = 220 V.

10. Electric Power

50


59/74


Resistance of electrical appliance

If variation of resistance with temperature is neglected then resistance of any

electrical appliance can be calculated from its rated power and rated voltage by using

Power consumed

An electrical appliance (Bulb, heater, etc.) consume rated power (PR) only if

applied voltage (VA) is equal to rated voltage (VR) i.e. If VA = VR

So

So

Long distance power transmission

When power is transmitted through a power line of resistance R, power-loss will be

i2RNow if the power P is transmitted at voltage V then P = VI, i.e.

i = (P / V)

So, Power loss

2Now as for a given power and line, P and R are constant. Hence Power loss (1/V )

So if power is transmitted at high voltage, power loss will be small and vice-versa.This is why long distance power transmission is carried out at high voltage.

1. The price of electricity consumed is calculated on the basis of electrical energy

consumed and not on the basis of electrical power.

2. The unit joule for energy is very small. Hence a big practical unit is known as

kilowatt hour (KWH) or board of trade unit (B.T.U.) is used as the practical

commercial unit

10.1 Electricity Consumption

Z

R

R

VR=

P


60/74


3. 1 kWh or 1 commercial unit is the quantity of electrical energy which gets

dissipated in one hour in an electrical circuit when the electrical power in thecircuit is 1 kW thus .

4. A simple formulae to calculate the no. of consumed units is

Solved example 1: Two heater wires of equal length are first connected in series and

then in parallel. The ratio of heat produced in the two cases is

(A) 2 : 1 (B) 1 : 2 (C) 4 :1 (D) 1 : 4

Solution: (D) Power consumed means heat produced.

For constant potential difference Pconsumed = Heat

Solved example 2: A wire when connected to 220 V mains supply has power

dissipation P1. Now the wire is cut into two equal pieces which are connected in

parallel to the same supply. Power dissipation in this case is P2. Then P2 : P1 is

(A) 1 (B) 4 (C) 2 (D) 3

Solution: (B) When wire is cut into two equal parts then power dissipated by each

part is 2P1

So their parallel combination will dissipate powerP = 2P + 2P = 4P , which gives2 1 1 1

.

52


61/74


POST CONTENT

Revision Worksheet 1

1. The main cause of resistance to the flow of charge within an electrical wire is _____.

a. mobile charge carriers collide with atoms of the resistor

b. mobile charge carriers have mass (possess inertia) which resists their motion

c. the electric field which causes charge flow diminishes with distance

d. charge is consumed or used up as it flows through the wire

2. Resistance is quantifiable - that is, it can be measured and calculated. The standard

metric unit usedto express the amount of electrical resistance is the ____.

a. Joule b. Watt c. Volt d. Ohm

3. For the following pairs of wire descriptions, choose the wire which has the greatest

resistance.Resistance to charge flow will be greatest in . (Circle the best answer.)

a. a wire which is thin a wire which is thick

b. a wire which is long a wire which is short

c. a wire which is made of copper a wire which is made of plastic

d. a wire which is made of copper a wire which is made of silver

4. The rate at which charge flows through a circuit is ___________ to the resistance.

a. inversely related b. directly related c. not related

5. For the following pairs of circuit descriptions, choose the circuit which has the

greatest current.Given that all other factors are equal, the current will be greatest in a

circuit which has .a. a high resistance a low resistance

b. wires which are long wires which are short

c. wires which are wide wires which are thin

d. 12-gauge wires (2.1 mm diameter) 14-gauge wires (1.8 mm diameter)

e. copper wiring silver wiring


62/74


6. Resistance is not the only variable which effects the current in an electric circuit. The

current is also affected by the electric potential difference (? V) applied across itsends. The electric potential difference is simply the battery voltage. As the battery

voltage is increased, the current is _____________________ (increased, decreased).

7. A circuit is set up such that it has a current of 8.0 amps. What would be the new current

if

a. the resistance (R) is increased by a factor of 2?

b. the resistance (R) is increased by a factor of 4?

c. the resistance (R) is decreased by a factor of 3?

d. the battery voltage (V) is increased by a factor of 3?

e. the battery voltage (V) is decreased by a factor of 2?

f. the resistance (R) is increased by a factor of 2 and the battery voltage (V) is

decreased by a factor of 2?

g. the resistance (R) is decreased by a factor of 4 and the battery voltage (V) is

increased by a factor of 3?

8. Express your understanding of the use of the I = V / R equation by filling in the

following blanks.

a. An electrical device with a resistance of 2.0 ? has an electric potential difference

of 6.0 V impressed across it; the current in the device is _____ amperes.

b. An electrical device with a resistance of 3.0 ? has an electric potential difference

of ______ V impressed across it; the current in the device is 4.0 amperes.

c. An electrical device with a resistance of _____ ? has an electric potential

difference of 120 V impressed across it; the current in the device is 6.0 amperes.

9. Resistors are electrical devices designed to have a specific resistance. They are

inserted in circuits to modify the actual current flowing through the circuit.

Which of the resistors in the two circuits (A or B) has the greatest resistance? Calculate

the value.

54


63/74


10. Use arrows to show the direction of conventional current flow through the following

circuits and use the I = ?V / R equation to fill in the blanks.

For a given amount of water pressure, which will flow a greater rate of water: a small

(restrictive) nozzle or a large (unrestrictive) nozzle? Explain how this relates to the study of

voltage, current, and resistance in a simple electric circuit.

Suppose you were to build this circuit and take measurements of current through the

resistor and voltage across the resistor:

Revision Worksheet 2

Question 1:

Question 2:


64/74


Recording these numerical values in a table, the results look something like this:

Current Voltage

0.22 A 0.66 V

0.47 A 1.42 V

0.85 A 2.54 V

1.05 A 3.16 V

1.50 A 4.51 V

1.80 A 5.41 V

2.00 A 5.99 V

2.51 A 7.49 V

Plot these figures on the following graph:

56

cbse i curricula x

Documents