ccna 4th module final 1 get 80% guranty
TRANSCRIPT
Top of FormWhat is a function that is associated with the access layer in a hierarchically designed network?
performs routing and packet manipulation
supplies redundancy and failover protection
provides a high-speed, low-latency backbone
serves as a network connection point for IP telephony devices
Top of FormWhat can be broadcast over the wireless network to help a user connect to the network and use wireless services?
SSID
WEP keys
VLAN parameters
WPA encryption keys
VPN authentication information
Top of FormWhat is the advantage of choosing EasyVPN for a new VPN implementation?
to provide encryption algorithms unavailable in other systems
to ensure that remote workers actually use the VPN for connectivity
to allow a greater variety of network devices to be used for VPN connections
to simplify the configuration tasks for the device that is used as the VPN server
Top of FormA company has help desk staff that is not highly trained in VPNs. What two features or technologies must the network designer identify as training needs in order for the help desk to support secure remote access for teleworkers? (Choose two.)
QoS operation
VLAN configuration
tunneling protocols
IPv6 and IPv4 dual stack
encryption algorithms
Frame Relay configuration
Which statement best describes the VPN feature called split tunneling?
It creates separate pathways for different VLANs
. It creates two tunnels, one for user traffic and one for management traffic such as CDP and SNMP.
It allows user traffic that is destined for the corporate network to travel across the VPN tunnel, while traffic destined for the Internet travels through the local LAN of the VPN client.
It allows separate tunnels so that high priority traffic, such as voice and video, uses the higher bandwidth tunnel, while all other user traffic travels on the lower bandwidth tunnel.
Top of FormThe network infrastructure at the headquarters of an organization consists of Cisco network devices that are running RIPv1. As part of an upgrade project, a portion of the company backbone will be increased to 10 Gb/s and needs to support unequal cost load balancing between routers. The IP addressing scheme is also changing and needs to support VLSM and CIDR. Which routing protocol should be selected for the network?
BGP
EIGRP
OSPF
RIPv2
Top of FormA NetworkingCompany engineer is on a support call resolving technical problems for a client network. After the issue is resolved, the engineer also provides a training session for the network support staff. What role is the engineer filling on the networking company team?
post-sales field engineer
pre-sales engineer
network designer
account manager
Top of Form
Refer to the exhibit. What can be concluded from the output that is shown?MDF_R1 has a MAC address of 2294:300F:0000.
MDF_R1 is connected through FastEthernet0/1 to C2960-24TT-L_IDF1.
Device C2960-24TT-L_IDF1 is running Cisco IOS Software Release 12.2(25)SEE2.
MDF_R1 is installed in the main distribution facility on floor 24 of building L.
Top of Form
Refer to the exhibit. In the Cisco IOS filename that is shown, what is signified by the underlined portion?
version
platform
file format
feature set
Top of FormA network administrator has removed a router from the network for maintenance. A new Cisco IOS software image has been successfully downloaded to a server and copied into the flash of the router. What should the administrator do before placing the router back into service?
Delete the previous version of the Cisco IOS software from flash.
Copy the new IOS into NVRAM to create a backup copy.
Restart the router and verify that the new image starts successfully.
Verify the free space available on the router to store the new IOS image.
Top of FormA network technician needs to install a four-port switch module in an operational Cisco 1841 router that has an available HWIC slot. What should the technician do first?
Turn off the power to the router before installing the new module.
Install the hot-swappable four-port switch module directly into slot 1 of the 1841.
Move the existing WIC-2T module to slot 1 and install the four-port module in slot 0.Shut down all Fast Ethernet ports on the router until the switch module installation is complete.
Refer to the exhibit. An administrator installs a WIC-2T module into a Cisco 1841 router. Attempts to configure the S0/0/0 interface are unsuccessful. As a first step in troubleshooting the failure, the administrator issues the show version command. What is a possible reason for the failure?
The WIC was not physically installed properly.
The WIC was installed into slot 1 instead of slot 0. The interface type and number are invalid on
an 1841. The configuration register is the wrong value for adding new modules.
Refer to the exhibit. Which type of application communication model best describes this network?
client-client client-server farm client-enterprise edge client-enterprise server
Top of FormIf traditional phones are used when introducing VoIP to a network, what component would be required to convert the analog voice from traditional telephone signals into IP packets?
Multipoint control unit
Power over Ethernet switches
a router that acts as a voice gateway
Cisco Unified Communications Manager
Which characteristic should be considered by a network designer when implementing a VoIP solution?
VoIP traffic is generally classified as low priority. VoIP centrally routes calls in the same manner
as a traditional PBX. VoIP traffic is highly reliable because of retransmission of dropped packets
. VoIP can make use of QoS features to help reduce interruptions in communication.
Top of FormWhich feature relies on prioritization of network traffic and is used to ensure successful delivery of real-time services?
security
reliability
redundancy
quality of service
When implementing an IP telephony solution, why should VLANs be used?
to allow the use of a single IP gateway
to separate voice from data traffic for ease of prioritization to allow the PBX to use VLAN IDs to
filter both voice and data traffic to allow connectivity between traditional phone devices and IP-based telephony devices
A customer of a large multisite organization has asked a network engineer to compare a new IPv4 addressing strategy with an IPv6 strategy for their new network implementation. Which tool is
appropriate for testing and comparing both addressing schemes?
NBAR Cisco SDM Network Assistant
network simulation toolA network administrator wants to configure a router that is running EIGRP so that it will advertise a route that will summarize the networks that are shown. Which network will summarize only these networks?
192.168.12.0/24 192.168.13.0/24 192.168.14.0/24 192.168.15.0/24
192.168.0.0/16 192.168.0.0/20 192.168.8.0/21 192.168.12.0/22
192.168.16.0/22------------
Top of FormA network administrator of a middle-sized company is asked to upgrade the routing protocol of the network to support VLSM and route summarization. The current company network contains both Cisco and non-Cisco routers. Which routing protocol should be used for the upgrade?
BGP
RIPv1
RIPv2
EIGRPTop of Form
During prototype testing, a LAN switch fails. As the switch re-initializes using the default parameters, a port that has a PC attached transitions to the forwarding state within one second. What protocol would support this feature?
STP
RIP
BGP
VTP
RSTPTop of Form
When designing a prototype network for a new server farm, a network designer chooses to use redundant links to connect to the rest of the network. Which business goal will be addressed by this choice?
security
scalability
availability
manageabilityTop of Form
Refer to the exhibit. To provide better customer service, the network management decides to implement a new server farm, which is located in a data center. Which two technology implementations will address the requirements for strict security policies to prevent unauthorized access to the server farm? (Choose two.)
Install firewalls and IDS capabilities on the network.
Apply ACLs to permit only inbound TCP traffic to the servers.
Apply filters that permit traffic only to required ports on the servers.
Configure a flexible IP addressing structure that allocates a single subnet per VLAN.
Configure a fast-converging routing protocol with authentication at the core layer.
Create a management VLAN and provide access to the data center devices through Telnet.Top of Form
A wireless survey has been conducted before the deployment of a wireless network. What would be the benefit of the survey?
provides initial configuration of the access points
determines the channel settings of the access points
determines the security settings on the access points
finds the optimal number and placement of access points
Refer to the exhibit. What does the TOR router do with traffic that is destined for a web server with an IP address of 172.18.10.24?
The router sends the traffic out Serial 0/0/0. The router sends the traffic out all interfaces other
than the one it came in on. The router places the packets into a queue until a better route is
discovered via RIP. The router sends a request to neighboring routers for paths to the 172.18.10.0 network
A user in a large office calls technical support to complain that a PC has suddenly lost connectivity to the network. The technician asks the caller to talk to nearby users to see if other machines are affected. The caller reports that several immediate neighbors in the same department have a similar problem and that they cannot ping each other. Those who are seated in other departments have connectivity. What should the technician check as the first step in troubleshooting the issue?
the power outlet to the PC that is used by the caller. the trunks between switches in the wiring closet.
the status of the departmental workgroup switch in the wiring closet. the cable that connects
the PC of the caller to the network jack. the cable connection between a PC and a network outlet that is used by a neighbor.
Top of FormA company would like to ensure that the failure of a single access switch does not disrupt service to the mail servers located in the data center. What can be done to ensure maximum connectivity to the mail servers?
Enable CDP to ensure all neighboring devices are known.
Create a separate RSTP specifically for the mail servers.
Configure a routing protocol so that paths to all Layer 3 devices are cached.
Install redundant access links between the servers and the access layer switches.
Refer to the exhibit. An extended ACL has been created to deny traffic from the 192.168.35.0/24 network to the web server with IP address 209.165.201.15. According to Cisco best practices, where
should the ACL be applied?
RTB Fa0/0 inbound RTC S0/0/1 inbound RTD Fa0/0 outbound RTC S0/1/0 outbound
The main office of a NetworkingCompany customer currently connects to three branch offices via three separate point-to-point T1 circuits. The customer network uses RIPv2 as the routing protocol within
both the LAN and the WAN. The account manager proposes a change to a Frame Relay network because the costs are lower. A single local loop connection can be installed at the main office with three separate
PVCs to connect the branch offices. How can the main office edge router be configured to enable the customer to continue to use RIP as the WAN routing protocol?
Enable Inverse ARP on the serial interface in order to learn the routes to the IP addresses of the remote routers.
To prevent the Frame Relay network from causing a routing loop, disable split horizon on the serial interface
. Create three separate point-to-point subinterfaces on the serial interface and assign a different
subnet IP address to each one. Configure the serial interface with a single interface DLCI number and create frame-relay map statements for each remote site address.
---------------
Top of FormA company is concerned with protecting internal e-commerce servers against external attacks.
An application layer firewall is installed at the network edge and a host-based IDS system is installed on the internal LAN. What should be done to ensure a fast response and minimum server downtime in the event of an external attack?
Replace the host-based IDS with an IPS.
Place the e-commerce servers in a DMZ.
Install a logging server to monitor all attacks.
Replace the application layer firewall with a stateful one.Top of Form
Which two security best practices are recommended for a router deployed as a WAN endpoint? (Choose two.)
Turn off unnecessary services.
Enable HTTP for web administration.
Configure easy to remember passwords.
Apply timeouts on VTY, AUX, and console ports.
Enable Telnet access to allow for remote management.
Company XYZ requires a WAN solution that provides flexible bandwidth options and supports one physical interface at the head office that would provide simultaneous connectivity to various remote
sites. The distance from each site should not make the solution more expensive. Which WAN technology meets the requirements of the company?
DSL cable
Frame Relay T1 leased line
Refer to the exhibit. A pre-sales system engineer receives a diagram of the current WAN from a customer. EIGRP is the routing protocol used on the WAN. Based on the default operation of EIGRP,
which statement is true about the routing table on router R1?
There is a single route to the 192.168.16.0/24 LAN using the T1 connection. There is a single
route to the 192.168.16.0/24 LAN using the DSL connection. There is a single route to the
192.168.16.0/24 LAN using the Metro Ethernet connection. EIGRP installs all three routes to the 192.168.16.0/24 LAN and load balances the traffic.
Which feature of network design and configuration would be considered a weakness?
Choosing a flat network model. Choosing to implement an IPS instead of IDS. Choosing to
disable Telnet and allow only SSH connections for remote access to the core routers. Choosing not to broadcast the SSID for wireless access points.
Refer to the exhibit. What can the field engineer conclude about the EIGRP authentication between Router1 and Router2?
Authentication will fail because only one key is configured. Authentication will succeed and
EIGRP updates can be exchanged. Authentication will fail because the key chain names do not
match. Authentication will fail because the key chain names must match the router names.
Refer to the exhibit. A networking engineer is characterizing an existing network for a new customer. The engineer issues a show running-config command on the R1 router to gather configuration information. What is the engineer able to determine as a result of viewing the output of this command?
The R1 router has two specific routes to the main office LANs in the routing table. The default
route for the R1 router points to the Edge1 router. The R1 router will load-balance traffic to the
main office LANs by using both DSL and Frame Relay. A connection through ISP-1 will be used to reach the main office LANs if the Frame Relay network is unavailable.
Refer to the exhibit. Which username and password combination will correctly configure PPP authentication on routers RTR_A and RTR_B?
Top of FormWhat are two accurate descriptors of a DLCI? (Choose two.)
Frame Relay Layer 2 address
one DLCI allowed per local loop
locally significant circuit endpoint
signaling standard between DTE and DCE
establishes the data transfer rate through a Frame Relay network
Which two values represent valid IPv6 addresses? (Choose two.)
::::1 FF01::1 0:0:0:0:0:0:0:1 2001:DB8::47::2A4 2031:0000:04AC:3400:FFE3:0