cellular concepts
DESCRIPTION
TRANSCRIPT
![Page 1: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/1.jpg)
Ch t 3Chapter 3
The Cellular Concept - System Designp y gFundamentals
![Page 2: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/2.jpg)
I. Introduction
Goals of a Cellular System High capacity L Large coverage area Efficient use of limited spectrum
Large coverage area - Bell system in New York City g g y yhad early mobile radio Single Tx, high power, and tall tower Low cost Low cost Large coverage area - Bell system in New York City had 12
simultaneous channels for 1000 square miles S ll # Small # users Poor spectrum utilization
What are possible ways we could increase the number
2
p yof channels available in a cellular system?
![Page 3: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/3.jpg)
Cellular concept Frequency reuse pattern
3
![Page 4: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/4.jpg)
Cells labeled with the same letter use the same group of channels.
C ll Cl f N ll i l f Cell Cluster: group of N cells using complete set of available channels
Many base stations lower power and shorter Many base stations, lower power, and shorter towers
Small coverage areas called “cells”g Each cell allocated a % of the total number of
available channels Nearby (adjacent) cells assigned different channel
groups t t i t f b t i hb i b
4
to prevent interference between neighboring base stations and mobile users
![Page 5: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/5.jpg)
Same frequency channels may be reused by cells a “reasonable” distance away reused many times as long as interference between same reused many times as long as interference between same
channel (co-channel) cells is < acceptable level As frequency reuse↑→ # possible simultaneous
users↑→ # subscribers ↑→ but system cost ↑ (moreusers↑→ # subscribers ↑→ but system cost ↑ (more towers)
To increase number of users without increasing radio frequency allocation reduce cell sizes (more basefrequency allocation, reduce cell sizes (more base stations) ↑→ # possible simultaneous users ↑
The cellular concept allows all mobiles to be f d h f f imanufactured to use the same set of freqencies
*** A fixed # of channels serves a large # of users by reusing channels in a coverage area ***
5
by reusing channels in a coverage area ***
![Page 6: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/6.jpg)
II. Frequency Reuse/Planning
Design process of selecting & allocating Design process of selecting & allocating channel groups of cellular base stations
Two competing/conflicting objectives: Two competing/conflicting objectives:1) maximize frequency reuse in specified area2) minimize interference between cells2) minimize interference between cells
6
![Page 7: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/7.jpg)
Cells base station antennas designed to cover specific cell
area hexagonal cell shape assumed for planning simple model for easy analysis → circles leave gaps actual cell “footprint” is amorphous (no specific shape) where Tx successfully serves mobile unit where Tx successfully serves mobile unit
base station location cell center → omni-directional antenna (360° coverage) cell center → omni directional antenna (360 coverage) not necessarily in the exact center (can be up to R/4
from the ideal location)
7
![Page 8: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/8.jpg)
cell corners → sectored or directional antennas on 3 corners with 120° coverage. very commom Note that what is defined as a “corner” is
somewhat flexible → a sectored antenna coverssomewhat flexible → a sectored antenna covers 120° of a hexagonal cell.
So one can define a cell as having three antennas gin the center or antennas at 3 corners.
8
![Page 9: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/9.jpg)
III. System Capacity
S : total # of duplex channels available for use in a given area; determined by:g ; y amount of allocated spectrum channel BW → modulation format and/or standard
specs. (e.g. AMPS) k : number of channels for each cell (k < S)( ) N : cluster size → # of cells forming cluster S = k N S k N
9
![Page 10: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/10.jpg)
M : # of times a cluster is replicated over a geographic coverage area
System Capacity = Total # Duplex Channels = C System Capacity Total # Duplex Channels C
C = M S = M k N( i l MN ll ill h )(assuming exactly MN cells will cover the area)
If cluster size (N) is reduced and the geographic area for each cell is kept constant:p The geographic area covered by each cluster is smaller, so
M must ↑ to cover the entire coverage area (more clusters needed).)
S remains constant. So C ↑ The smallest possible value of N is desirable to maximize
10
The smallest possible value of N is desirable to maximize system capacity.
![Page 11: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/11.jpg)
Cluster size N determines: distance between co-channel cells (D)( ) level of co-channel interference A mobile or base station can only tolerate so much y
interference from other cells using the same frequency and maintain sufficient quality.
large N → large D → low interference → but small M and low C !
T d ff i lit d l t i Tradeoff in quality and cluster size. The larger the capacity for a given geographic area,
the poorer the quality
11
the poorer the quality.
![Page 12: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/12.jpg)
Frequency reuse factor = 1 / N each frequency is reused every N cellsq y y each cell assigned k S / N
N cells/cluster N cells/cluster connect without gaps specific values are required for hexagonal geometryspecific values are required for hexagonal geometry N = i2 + i j + j2 where i, j ≧ 1 Typical N values → 3, 4, 7, 12; (i, j) = (1,1), (2,0),
(2,1), (2,2)
12
![Page 13: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/13.jpg)
To find the nearest co-channel neighbors of a particular cell (1) Move i cells along any chain of hexagons, then (2)
turn 60 degrees and move j cells.
13
![Page 14: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/14.jpg)
14
![Page 15: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/15.jpg)
15
![Page 16: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/16.jpg)
IV. Channel Assignment Strategies
Goal is to minimize interference & maximize use of capacity l i t f ll ll N t b d t lower interference allows smaller N to be used → greater
frequency reuse → larger C
Two main strategies: Fixed or Dynamicg y Fixed each cell allocated a pre-determined set of voice channels calls within cell only served by unused cell channels all channels used → blocked call → no service
several variations several variations MSC allows cell to borrow a VC (that is to say, a FVC/RVC
pair) from an adjacent cell
16
donor cell must have an available VC to give
![Page 17: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/17.jpg)
Dynamic channels NOT allocated permanently call request → goes to serving base station → goes
to MSC MSC allocates channel “on the fly” allocation strategy considers: lik lih d f f t ll bl ki i th ll likelihood of future call blocking in the cell reuse distance (interference potential with other cells
that are using the same frequency) channel frequency
All frequencies in a market are available to be used
17
![Page 18: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/18.jpg)
Advantage: reduces call blocking (that is to say, it increases the trunking capacity), and g p y),increases voice quality
Disadvantage: increases storage & g gcomputational load @ MSC requires real-time data from entire network related q
to: channel occupancy traffic distribution Radio Signal Strength Indications (RSSI's) from all
channels
18
channels
![Page 19: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/19.jpg)
V. Handoff Strategies
Handoff: when a mobile unit moves from one cell to another while a call is in progress, the p g ,MSC must transfer (handoff) the call to a new channel belonging to a new base station new voice and control channel frequencies very important task → often given higher priority
than new call It is worse to drop an in-progress call than to deny a
new onenew one
19
![Page 20: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/20.jpg)
Minimum useable signal level Minimum useable signal level lowest acceptable voice quality call is dropped if below this levelc s d opped be ow s eve specified by system designers typical values → -90 to -100 dBmyp
20
![Page 21: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/21.jpg)
Quick review: Decibels
S = Signal power in WattsPower of a signal in decibels (dBW) is Psignal = 10 log10(S)
Remember dB is used for ratios (like S/N)dBW is used for Watts
dBm = dB for power in milliwatts = 10 log10(S x 103)dBm = 10 log10(S) + 10 log10(103) = dBW + 30
90 dBm = 10 log10(S x 103)-90 dBm = 10 log10(S x 103)10-9 = S x 103
S = 10-12 Watts = 10-9 milliwatts-90 dBm = -120 dBW90 dBm 120 dBW
Signal-to-noise ratio:N = Noise power in Watts
21
pS/N = 10 log10(S/N) dB (unitless raio)
![Page 22: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/22.jpg)
choose a (handoff threshold) > (minimum useable signal level)g ) so there is time to switch channels before level
becomes too low as mobile moves away from base station and
toward another base station
22
![Page 23: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/23.jpg)
23
![Page 24: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/24.jpg)
Handoff Margin △ △ = Phandoff threshold - Pminimum usable signal dB carefully selected △ too large → unnecessary handoff → MSC loaded down △ too small → not enough time to transfer → call dropped! △ too small → not enough time to transfer → call dropped!
A dropped handoff can be caused by two factors not enough time to perform handoffg p delay by MSC in assigning handoff high traffic conditions and high computational load on MSC
can cause excessive delay by the MSCcan cause excessive delay by the MSC no channels available in new cell
24
![Page 25: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/25.jpg)
Handoff Decision signal level decreases due to signal fading → don’t handoff mobile moving away from base station → handoff
t it i d i l t th i d must monitor received signal strength over a period of time → moving average
time allowed to complete handoff depends on t e a owed to co p ete a do depe ds omobile speed large negative received signal strength (RSS) slope →
high speed → quick handoffhigh speed → quick handoff statistics of the fading signal are important to
making appropriate handoff decisions → Chapters
25
g pp p p4 and 5
![Page 26: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/26.jpg)
1st Generation Cellular (Analog FM → AMPS) Received signal strength (RSS) of RVC measuredReceived signal strength (RSS) of RVC measured
at base station & monitored by MSC A spare Rx in base station (locator Rx) monitors
RSS of RVC's in neighboring cells Tells Mobile Switching Center about these mobiles and
their channelstheir channels Locator Rx can see if signal to this base station is
significantly better than to the host base stationg y MSC monitors RSS from all base stations &
decides on handoff
26
![Page 27: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/27.jpg)
2nd Generation Cellular w/ digital TDMA (GSM, IS-136) Mobile Assisted HandOffs (MAHO) important advancement The mobile measures the RSS of the FCC’s from
adjacent base stations & reports back to serving base stationstation
if Rx power from new base station > Rx power from serving (current) base station by pre-determined margin for a long enough time period → handoff initiated by MSC
27
![Page 28: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/28.jpg)
MSC no longer monitors RSS of all channels d t ti l l d id bl reduces computational load considerably enables much more rapid and efficient handoffs imperceptible to user imperceptible to user
28
![Page 29: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/29.jpg)
A mobile may move into a different system controlled by a different MSC Called an intersystem handoff What issues would be involved here?
Prioritizing Handoffs I P i d G d f S i (GOS) i Issue: Perceived Grade of Service (GOS) – service
quality as viewed by users “quality” in terms of dropped or blocked calls (not q y pp (
voice quality) assign higher priority to handoff vs. new call request a dropped call is more annoying than an occasional
29
a dropped call is more annoying than an occasional blocked call
![Page 30: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/30.jpg)
Guard Channels % of total available cell channels exclusively set % of total available cell channels exclusively set
aside for handoff requests makes fewer channels available for new call
requests a good strategy is dynamic channel allocation (not
fixed) adjust number of guard channels as needed by demand so channels are not wasted in cells with low traffic so channels are not wasted in cells with low traffic
30
![Page 31: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/31.jpg)
Queuing Handoff Requests use time delay between handoff threshold and y
minimum useable signal level to place a blocked handoff request in queue
a handoff request can "keep trying" during that time period, instead of having a single block/no block decisiondecision
prioritize requests (based on mobile speed) and handoff as needed
calls will still be dropped if time period expires
31
![Page 32: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/32.jpg)
VI. Practical Handoff Considerations
Problems occur because of a large range of Problems occur because of a large range of mobile velocities pedestrian vs. vehicle userpedestrian vs. vehicle user
Small cell sizes and/or micro-cells → larger # handoffshandoffs
MSC load is heavy when high speed users are passed between very small cellspassed between very small cells
32
![Page 33: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/33.jpg)
Umbrella Cells Fig. 3.4, pg. 67g , pg use different antenna heights and Tx power levels to
provide large and small cell coverage multiple antennas & Tx can be co-located at single
location if necessary (saves on obtaining new tower li )licenses)
large cell → high speed traffic → fewer handoffs ll ll l d t ffi small cell → low speed traffic example areas: interstate highway passing thru
urban center office park or nearby shopping mall
33
urban center, office park, or nearby shopping mall
![Page 34: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/34.jpg)
34
![Page 35: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/35.jpg)
Cell Dragging low speed user w/ line of sight to base station (very strong
signal) strong signal changing slowly user moves into the area of an adjacent cell without handoff user moves into the area of an adjacent cell without handoff causes interference with adjacent cells and other cells Remember: handoffs help all users, not just the one which is
h d d ffhanded off. If this mobile is closer to a reused channel → interference -
for the other user using the same frequency So this mobile needs to hand off anyway, so other users
benefit because that mobile stays far away from them.
35
![Page 36: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/36.jpg)
Typical handoff parameters Analog cellular (1st generation) Analog cellular (1st generation) threshold margin △ ≈ 6 to 12 dB total time to complete handoff ≈ 8 to 10 sec
Digital cellular (2nd generation) total time to complete handoff ≈ 1 to 2 sec l th h ld i △ 0 t 6 dB lower necessary threshold margin △ ≈ 0 to 6 dB enabled by mobile assisted handoff
36
![Page 37: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/37.jpg)
benefits of small handoff time greater flexibility in handling high/low speed g y g g p
users queuing handoffs & prioritizing more time to “rescue” calls needing urgent
handoff f d d ll GOS i d fewer dropped calls → GOS increased
can make decisions based on a wide range of metrics other than signal strengthmetrics other than signal strength such as also measure interference levels can have a multidimensional algorithm for
37
can have a multidimensional algorithm for making decisions
![Page 38: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/38.jpg)
Soft vs. Hard Handoffs Hard handoff: different radio channels assigned
when moving from cell to cell all analog (AMPS) & digital TDMA systems (IS-136,
GSM, etc.)GS , e c.) Many spread spectrum users share the same
frequency in every cell CDMA → IS-95 Since a mobile uses the same frequency in every cell, it
can also be assigned the same code for multiple cells when it is near the boundary of multiple cells.
The MSC simultaneously monitors reverse link signal at several base stations
38
![Page 39: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/39.jpg)
MSC dynamically decides which signal is best and then listens to that oneand then listens to that one Soft Handoff passes data from that base station on to the PSTNp
This choice of best signal can keep changing. Mobile user does nothing for handoffs except ob e use does ot g o a do s e cept
just transmit, MSC does all the work Advantage unique to CDMA systemsg q y As long as there are enough codes available.
39
![Page 40: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/40.jpg)
VII. Co-Channel Interference
Interference is the limiting factor in performance of all cellular radio systems
What are the sources of interference for a mobile receiver?
Interference is in both voice channels
l h l control channels Two major types of system-generated
interference:interference:1) Co-Channel Interference (CCI)2) Adjacent Channel Interference (ACI)
40
2) Adjacent Channel Interference (ACI)
![Page 41: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/41.jpg)
First we look at CCI Frequency Reuse Frequency Reuse Many cells in a given coverage area use the same
set of channel frequencies to increase system q ycapacity (C)
Co-channel cells → cells that share the same set of frequencies
VC & CC traffic in co-channel cells is an interfering source to mobiles in Several differentinterfering source to mobiles in Several different cells
41
![Page 42: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/42.jpg)
Possible Solutions?1) Increase base station Tx power to improve radio ) p p
signal reception? __ this will also increase interference from co-channel
ll b hcells by the same amount no net improvement
2) Separate co channel cells by some minimum2) Separate co-channel cells by some minimum distance to provide sufficient isolation from propagation of radio signals? if all cell sizes, transmit powers, and coverage patterns
≈ same → co-channel interference is independent of Tx power
42
Tx power
![Page 43: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/43.jpg)
co-channel interference depends on: co channel interference depends on: R : cell radius D : distance to base station of nearest co-channel cell
if D / R ↑ then spatial separation relative to cell coverage area ↑ i d i l i f h l RF improved isolation from co-channel RF energy
Q = D / R : co-channel reuse ratio hexagonal cells → Q = D/R = 3N hexagonal cells → Q = D/R = 3N
43
![Page 44: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/44.jpg)
Fundamental tradeoff in cellular system design: small Q → small cluster size → more frequency
reuse → larger system capacity great But also: small Q → small cell separation →
increased co channel interference (CCI) → reducedincreased co-channel interference (CCI) → reduced voice quality → not so great
Tradeoff: Capacity vs. Voice Quality Tradeoff: Capacity vs. Voice Quality
44
![Page 45: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/45.jpg)
Signal to Interference ratio → S / I, ____________
S : desired signal powerg p Ii : interference power from ith co-channel cell io : # of co-channel interfering cells
45
![Page 46: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/46.jpg)
Approximation with some assumptions
Di : distance from ith interferer to mobile Rx power @ mobile ( ) n
iD
46
![Page 47: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/47.jpg)
n : path loss exponent free space or line of sight (LOS) (no obstruction) →
n = 2 urban cellular → n = 2 to 4, signal decays faster
ith di t f th b t tiwith distance away from the base station having the same n throughout the coverage area
means radio propagation properties are roughly themeans radio propagation properties are roughly the same everywhere
if base stations have equal Tx power and n is the q psame throughout coverage area (not always true) then the above equation (Eq. 3.8) can be used.
47
![Page 48: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/48.jpg)
Now if we consider only the first layer (or tier) of co-channel cells assume only these provide significant interference
And assume interfering base stations are And assume interfering base stations are equidistant from the desired base station (all at distance ≈ D) then)
48
![Page 49: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/49.jpg)
What determines acceptable S / I ? voice quality → subjective testingq y j g AMPS → S / I 18 dB (assumes path loss exponent
n = 4) Solving (3.9) for N
Most reasonable assumption is io : # of co-channel interfering cells = 6
N 7 ( h i f AMPS)
49
N = 7 (very common choice for AMPS)
![Page 50: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/50.jpg)
Many assumptions involved in (3.9) : same Tx powerp hexagonal geometry n same throughout areag Di ≈ D (all interfering cells are equidistant from the
base station receiver) optimistic result in many cases propagation tools are used to calculate S / I when
i lidassumptions aren’t valid
50
![Page 51: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/51.jpg)
S / I is usually the worst case when a mobile is at the cell edge low signal power from its own base station & high
interference power from other cells more accurate approximations are necessary in those cases more accurate approximations are necessary in those cases
4
4 4 42( ) 2( ) 2S RI D R D R D
4 4 42( ) 2( ) 2I D R D R D
51
![Page 52: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/52.jpg)
N =7 and S / I ≈ 17 dB
52
![Page 53: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/53.jpg)
Eq. (3.5), (3.8), and (3.9) are (S / I) for forward link only, i.e. the cochannel base Tx interfering with desired base station transmission to mobile unit so this considers interference @ the mobile unit
What abo t reverse link co channel interference? What about reverse link co-channel interference? less important because signals from mobile antennas (near
the ground) don’t propagate as well as those from tall base station antennas
obstructions near ground level significantly attenuate mobile energy in direction of base station Rxenergy in direction of base station Rx
also weaker because mobile Tx power is variable → base stations regulate transmit power of mobiles to be no larger than necessary
53
than necessary
![Page 54: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/54.jpg)
I. Adjacent Channel Interference
Two major types of system-generated interference:
1) Co-Channel Interference (CCI) – discussed in last lecture
2) Adjacent Channel Interference (ACI) Adjacent Channel Interference (ACI) Imperfect Rx filters allow energy from adjacent
channels to leak into the passband of other h lchannels
54
![Page 55: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/55.jpg)
d i d fil desired filter response
actual filter response actual filter response
55
![Page 56: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/56.jpg)
This affects both forward & reverse links Forward Link → base-to-mobile Forward Link → base to mobile interference @ mobile Rx from a ______ Tx
(another mobile or another base station that is not (the one the mobile is listening to) when mobile Rx is ___ away from base station.
signal from base station is weak and others are somewhat strong.
R Li k bil t b Reverse Link → mobile-to-base interference @ base station Rx from nearby mobile
Tx when desired mobile Tx is far away from base
56
Tx when desired mobile Tx is far away from base station
![Page 57: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/57.jpg)
Near/Far Effect interfering source is near some Rx when desired g
source is far away ACI is primarily from mobiles in the same cellp y some cell-to-cell ACI does occur as well → but a
secondary source Control of ACI don’t allocate channels within a given cell from a
contiguous band of frequencies for example, use channels 1, 4, 7, and 10 for a cell. h l t t h th
57
no channels next to each other
![Page 58: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/58.jpg)
maximize channel separation separation of as many as N channel bandwidths separation of as many as N channel bandwidths some schemes also seek to minimize ACI from
neighboring cells by not assigning adjacentneighboring cells by not assigning adjacent channels in neighboring cells
58
![Page 59: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/59.jpg)
59
![Page 60: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/60.jpg)
Originally 666 channels, then 10 MHz of spectrum was added
666+166 = 832 channels 395 VC plus 21 CC per service provider
(providers A & B)395*2 = 790, plus 42 control channels
Provider A is a company that has not traditionally provided telephone service
P id B i t diti l i li t Provider B is a traditional wireline operator 21 VC groups with ≈ 19 channels/group t l t 21 h l ti f h
60
at least 21 channel separation for each group
![Page 61: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/61.jpg)
for N = 7 → 3 VC groups/cell For example, choose groups 1A, 1B, and 1C for a p , g p , ,
cell – so channels 1, 8, 15, 22, 29, 36, etc. are used. ≈ 57 channels/cell at least 7 channel separation for each cell group
to have high quality on control channels, 21 cell g q yreuse is used for CC’s instead of reusing a CC every 7 cells, as for VC’s,
reuse every 21 cells (after every three clusters) greater distance between control channels, so less
CCI
61
CCI
![Page 62: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/62.jpg)
use high quality filters in base stations better filters are possible in base stations since they p y
are not constrained by physical size and power as much as in the mobile Rx
makes reverse link ACI less of a concern than forward link ACI also true because of power control (discussed below) also true because of power control (discussed below)
choice of modulation schemes diff t d l ti h id l different modulation schemes provide less or more
energy outside their passband.
62
![Page 63: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/63.jpg)
Power Control technique to minimize ACIq base station & MSC constantly monitor mobile
received signal strength mobile Tx power varied (controlled) so that
smallest Tx power necessary for a quality reverse li k i l i d (l f th l thlink signal is used (lower power for the closer the mobile is to the base station)
also helps battery life on mobile also helps battery life on mobile
63
![Page 64: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/64.jpg)
dramatically improves adjacent channel S / I ratio, since mobiles in other cells only transmit t hi h h t itt t lat high enough power as transmitter controls
(not at full power) most beneficial for ACI on reverse link most beneficial for ACI on reverse link will see later that this is especially important for
CDMA systemsCDMA systems
64
![Page 65: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/65.jpg)
III. Trunking & Grade of Service (GOS)
Trunked radio system: radio system where a large # of users share a pool of channelslarge # of users share a pool of channels channel allocated on demand & returned to channel
pool upon call terminationpool upon call termination exploit statistical (random) behavior of users so that
fixed # of channels can accommodate large # of users Trade-off between the number of available channels
that are provided and the likelihood of a particular userthat are provided and the likelihood of a particular user finding no channels available during the busy hour of the day.
65
![Page 66: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/66.jpg)
trunking theory is used by telephone companies to allocate limited # of voice circuits for large # ofallocate limited # of voice circuits for large # of telephone lines
efficient use of equipment resources → savingsq p g disadvantage is that some probability exists that
mobile user will be denied access to a channel blocked call : access denied → “blocked call cleared” delayed call : access delayed by call being put into
holding queue for specified amount of timeholding queue for specified amount of time
66
![Page 67: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/67.jpg)
GOS : measure of the ability of user access to a trunked system during the hourtrunked system during the _______ hour specified as probability (Pr) that call is blocked or
delayedy designed to handle the busiest hour → typically
______ Erlang : unitless measure of traffic intensity e.g. 0.5 erlangs = 1 channel occupied 30 minutes
during 1 hourduring 1 hour Table 3.3, pg. 78 → trunking theory definitions
67
![Page 68: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/68.jpg)
“Offered” Traffic Intensity (A) Offered? → not necessarily carried by system y y y
(some is blocked or delayed) each user Au=λH Erlangs (also called ρ in queueing
theory) λ = traffic intensity (average arrival rate of new calls,
in new requests per time unit say calls/min)in new requests per time unit, say calls/min). H = average duration of a call (also called 1/ µ in
queueing theory) system with U users → A = UAu = UλH Erlangs capacity = maximum carried traffic = C Erlangs =
68
(equal to total # of available channels that are busy all the time)
![Page 69: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/69.jpg)
Erlang B formula Calls are either admitted or blocked
A = total offered traffic C = # channels in trunking pool (e.g. a cell)g p ( g )
AMPS designed for GOS of 2% blocked call cleared (denied) → BCC
69
( )
![Page 70: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/70.jpg)
capacities to support various GOS values capacities to support various GOS values
N h i h i h h
70
Note that twice the capacity can support much more than twice the load (twice the number of Erlangs).
![Page 71: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/71.jpg)
Erlang C formulas blocked call delayed → BCD → put into holding y p g
queue GOS is probability that a call will still be blocked
even if it spends time in a queue and waits for up to t seconds
ti (3 17) t (3 19) i b k equations (3.17) to (3.19) in book
71
![Page 72: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/72.jpg)
Graphical form of Erlang B formulas
72
![Page 73: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/73.jpg)
Graphical form of Erlang C formulas
73
![Page 74: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/74.jpg)
Example: Find how many users can be supported in a cell containing 50 channels for a pp g2% GOS (Blocked Calls Cleared) if the average user calls twice/hr with an average call duration of 5 minutes.
What is the corresponding C from the figure? What is the corresponding C from the figure?
What is A (Traffic Intensity) from the figure?What is A (Traffic Intensity) from the figure?
So, how many users can be supported?
74
, y pp
![Page 75: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/75.jpg)
Trunking Efficiency measure of the # of users supported by a specific
configuration of fixed channels, efficiency in terms of users per available channel = U / C
Table 3 4 pg 79 → assume 1% GOS Table 3.4, pg. 79 → assume 1% GOS Assume Au = 0.2 1 group of 20 channels: 1 group of 20 channels:
2 groups of 10 channels, with equal number of users per group:
75
![Page 76: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/76.jpg)
the allocation of channel groups can substantially change the # of users supported by y g pp ytrunked system The larger the trunking pool, the better the trunking g g p g
efficiency. as trunking pool size ↓ then trunking efficiency
↓ What is the relationship between trunking pool size,
trunking efficiency, received signal quality, and cluster size?
As cluster size decreases
76
As cluster size decreases…
![Page 77: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/77.jpg)
Note: Trunking efficiency is an issue both in FDMA/TDMA t d i CDMA tFDMA/TDMA systems and in CDMA systems (where the capacity limit is the number of possible codes and the interference levels)possible codes and the interference levels).
77
![Page 78: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/78.jpg)
78
![Page 79: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/79.jpg)
79
![Page 80: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/80.jpg)
80
![Page 81: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/81.jpg)
81
![Page 82: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/82.jpg)
82
![Page 83: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/83.jpg)
83
![Page 84: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/84.jpg)
84
![Page 85: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/85.jpg)
85
![Page 86: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/86.jpg)
86
![Page 87: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/87.jpg)
87
![Page 88: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/88.jpg)
IV. Improving Cellular System Capacity
A cellular design eventually (hopefully!) becomes insufficient to support the growing number of users. Need to provide more channels per unit coverage
area Would like to have orderly growth
ld lik d h i d f b ild Would like to upgrade the system instead of rebuild Would like to use existing towers as much as
possiblepossible
88
![Page 89: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/89.jpg)
Cell Splitting subdivide congested cell into several smaller subdivide congested cell into several smaller
cells increases number of times channels are reused
in an area must decrease antenna height & Tx powerg p so smaller coverage per cell results and the co-channel interference level is held
constant
89
![Page 90: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/90.jpg)
each smaller cell keeps ≈ same # of channels as the larger cell, since each new smaller cell uses the same number of frequencies this means that we keep that same cluster size
capacity ↑ because channel reuse ↑ per unit area smaller cells → “micro-cells”
90
![Page 91: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/91.jpg)
Illustration is for towers at the corners
91
![Page 92: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/92.jpg)
advantages include: only needed for cells that reach max. capacity → not
all cells implement when Pr [blocked call] > acceptable GOS system capacity can gradually expand as demand ↑
disadvantages include: # handoffs/unit area increases umbrella cell for high velocity traffic may be needed more base stations → $$ for real estate, towers, etc.
92
![Page 93: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/93.jpg)
complicated design process new base stations use lower power and antenna
height What about existing base stations? If kept at the same power they would overpower new If kept at the same power, they would overpower new
microcells. If reduced in power, they would not cover their own
llcells. One solution: Use separate groups of channels. One group at the original power and another group at O e g oup e o g powe d o e g oup
the lower power. New microcells only use lower power channels. As load growth continues more and more channels are
93
As load growth continues, more and more channels are moved to lower power.
![Page 94: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/94.jpg)
94
![Page 95: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/95.jpg)
95
![Page 96: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/96.jpg)
Sectoring cell splitting keeps D / R unchanged (same
cluster size and CCI) but increases frequency reuse/area
alternate way to ↑ capacity is to _____ CCI (increase S / I ratio)
96
![Page 97: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/97.jpg)
replace omni-directional antennas at base station with several directional antennas 3 sectors → 3 120° antennas 6 sectors → 6 60° antennas
97
![Page 98: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/98.jpg)
ll h l b k d i d cell channels broken down into sectored groups CCI reduced because only some of neighboring co-
channel cells radiate energy in direction of main cellchannel cells radiate energy in direction of main cell center cell labeled "5" has all co-channel cells
illustratedillustrated only 2 co-channel cells will interfere if all are using
120° sectoring only 1 co-channel cell would interfere when using
60° sectoring If the S/I was 17 dB for N = 7 and n = 4, what is the
S / I now with 120° sectoring? 24 2 dB
98
24.2 dB
![Page 99: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/99.jpg)
99
![Page 100: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/100.jpg)
How is capacity increased? sectoring only improves S/I which increases voice
quality, beyond what is really necessary by reducing CCI, the cell system designer can choose
smaller cluster size (N ↓) for acceptable voice qualitysmaller cluster size (N ↓) for acceptable voice quality smaller N → greater frequency reuse → larger system
capacity
What would the system capacity, Cnew, now be when using 120° sectoring, as compared to the old capacity, Cold ?
100
![Page 101: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/101.jpg)
101
![Page 102: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/102.jpg)
102
![Page 103: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/103.jpg)
much less costly than cell splitting only require more antennas @ base station vs. y q @
multiple new base stations for cell splitting primary disadvantage is that the available p y g
channels in a cell are subdivided into sectored groups trunked channel pool ↓, therefore trunking
efficiency ↓ There are more channels per cell, because of
smaller cluster sizes, but those channels are broken into sectors
103
into sectors.
![Page 104: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/104.jpg)
other disadvantages: other disadvantages: must design network coverage with sectoring
decided in advance can’t effectively use sectoring to increase capacity
after setting cluster size N can’t be used to gradually expand capacity as
traffic ↑ like cell splittingd ff More Handoffs
More antenna, more cost
104
![Page 105: Cellular concepts](https://reader034.vdocument.in/reader034/viewer/2022042713/54755d0bb4af9fb90a8b5afa/html5/thumbnails/105.jpg)
Next topic: Mobile Radio Propagation - Large-scale path loss, small-scale fading, and p , g,multipath Free space propagation lossp p p g Reflections 2-ray model Diffraction Fading Multipath
105