cf-710ni / ibr-710ni - metra online · 2015-07-16 · 1 disconnect the negative battery terminal to...

INSTALLATION INSTRUCTIONS FOR PART CF-710NI / IBR-710NI

Cutting Tool • Phillips Screwdriver • Socket Wrench

1-800-221-0932 www.metraonline.com

METRA. The World’s Best Kits.

KIT FEATURES

© COPYRIGHT 2004-10 METRA ELECTRONICS CORPORATION

• DDIN Head Unit Provision• Stacked ISO DIN Head Unit Provision• ISO and DIN Provisions• Pocket (holds 2 jewel cases)

A) DDIN Trim plate B) DDIN Brackets C) Radio Housing D) (4) Phillips Pan Head Screws E) Iso Trim PlateF) Bracket Set#1 G) Bracket Set #2 H) ISO Brackets I) Bracket Set #3

KIT COMPONENTS

TOOLS REQUIRED:

CF-710NI / IBR-710NI

A B C D E

F G H I

APPLICATIONSINFINITI 1996-1999 I-30

MERCURY 1993-2002 Villager NISSAN 1995-1998 200SX/240SX

1998-2001 Altima / 1998-2004 Frontier1995-2003 Maxima / 1996-2004 Pathfinder/QX4 1997-2000

1993-2003 Quest / 1995-1999 Sentra2000-2004 Xterra

TABLE OF CONTENTSDash Disassembly1996-1999 Infiniti I-30 ............................................................................................... 11993-1995 Mercury Villager /1993-1995 Nissan Quest ............................................. 21996-1998 Mercury Villager/ 1996-1998 Nissan Quest ............................................. 31999-2002 Mercury Villager /1999-2003 Nissan Quest ..............................................41995-1999 Nissan Sentra /1995-1998 200 SX........................................................... 51995-1998 Nissan 240 SX .......................................................................................... 61998-2001 Nissan Altima ........................................................................................... 71998-2001 Nissan Frontier/2000-2001 Nissan Xterra ............................................... 82002-2004 Nissan Frontier/2002-2004 Nissan Xterra ............................................... 91995-1999 Nissan Maxima....................................................................................... 102000-2003 Nissan Maxima....................................................................................... 111996-2000 Nissan Pathfinder/QX4 1997-2000......................................................... 122001-2004 Nissan Pathfinder................................................................................... 13Fits all models EXCEPT the Bose and Comfort & Convenience pkgs.Kit AssemblyDouble DIN Head Unit Provision................................................................................ 14Stacked ISO DIN Head Unit Provision ....................................................................... 15 Mercury Villager 1993-98 ..........................................................................................16Mercury Villager/Nissan Quest 199-02 & Nissan 200SX 1995-98.............................17Nissan 240SX 1995-98 & Nissan Altima 1998-01 .....................................................18Nissan Frontier 1998-04............................................................................................19Nissan Maxima 1995-03............................................................................................20Nissan Pathfinder 1996-03........................................................................................21Nissan Quest 1993-98 ...............................................................................................22Nissan Sentra 1995-99 / Xterra 2000-01 ..................................................................23Infiniti I30 1996-99 / All Vehicles.........................................................................24-25Final Assembly...........................................................................................................26

CAUTION:Do not cycle the key when removing a dash with passenger airbag ON/OFF switch.

*

KNOWLEDGE IS POWEREnhance your installation and fabrication skillsby enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.comor call 800-354-6782 for more information and take steps toward a better tomorrow.

1

Disconnect the negative battery terminal to prevent an accidentalshort circuit.

1

Unclip and remove the shift levertrim panel and remove the (2)screws exposed.

2

1996-1999 INFINITI I-30

Remove (1) screw to the left of theashtray then unclip and remove theashtray assembly.

3

Unclip and remove the clock/ventassembly.

4

Remove (4) screws securing theradio.

5

DASH DISASSEMBLY

DASH DISASSEMBLY

1993-1995 MERCURY VILLAGER1993-1995 NISSAN QUEST


Remove (1) screw above the climatecontrols.

2

Unclip and remove the radio trimpanel.

3


4

1

2

3


1

Remove (4) plastic screws andscrew anchors from the base of thestorage compartment then removethe compartment.

2

Remove (2) Phillips screws fromabove the radio opening.

4

Remove the ashtray.5


6

Remove (2) Phillips screws from thebase of the radio trim panel.

3

DASH DISASSEMBLY



1

4

DASH DISASSEMBLY

Open the ashtray/cupholder assem-bly and depress the retaining clipson each side to remove.

2

Remove (2) Phillips screws fromeach side of the ashtray/cupholder.

3

Unclip the dash trim panel andremove.

5

Remove (4) Phillips screws securingthe radio.

6

Remove (4) plastic rivets from thelower pocket and slide the pocketback. Note: It is not necessary tofully remove the pocket.

4


5

Unclip and remove the dummy plateabove the climate controls.

2

Remove (1) Phillips screw frombehind dummy plate.

3

Unclip and remove radio trim panel.4

Remove (4) Phillips screws securingradio.

5

DASH DISASSEMBLY

1995-1999 NISSAN SENTRA1995-1998 200 SX


1

6

1995-1998 NISSAN 240 SX

DASH DISASSEMBLY

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

Unclip and remove the climate con-trol trim panel and remove the (2)exposed behind.

Unclip and remove the shift levertrim panel and remove the (2) screwsexposed behind.

1

2

3

Remove the ashtray and (1) Phillipsscrew exposed in the ashtray cavity.

4

Unclip and remove the radio trimpanel, factory radio and pocketassembly.

5

DASH DISASSEMBLY

1998-2001 NISSAN ALTIMA

7

Disconnect the negative battery terminalto prevent an accidental short circuit.

Unclip the shift lever trim panel andremove (2) Phillips screws at the baseof the radio trim panel.

1

2

Remove (2) Phillips screws above theradio opening.

3

1

Unclip and remove the radio trim panel.4

Remove (4) Phillips screws securing theradio.

5

DASH DISASSEMBLY

1998-2001 NISSAN FRONTIER2000-2001 NISSAN XTERRA

8


Remove the ashtray and the (2) Phillipsscrews exposed in the ashtray cavity.

1

2



4

DASH DISASSEMBLY

2002-2004 NISSAN FRONTIER2002-2004 NISSAN XTERRA

9


Unclip and remove the shift lever trimpanel.

1

2

Remove (2) Phillips screws exposed inthe shift lever cavity.

3

Remove (2) Phillips screws under theclimate control.

4



6

DASH DISASSEMBLY

1995-1999 NISSAN MAXIMA

10


Unclip the shift lever trim panel.

1

2

Remove the (2) Phillips screws at thebase of the radio trim panel.

3

Remove (1) Phillips screw to the left ofthe ashtray and unclip the ashtrayassembly.

4

Unclip and remove the clock/ventassembly.

5


6

DASH DISASSEMBLY

2000-2003 NISSAN MAXIMA

11


Unclip and remove the vent/radio trimpanel. Note: For Bose systems the ventassembly will be removed without thetrim panel.

1

2

Remove the ashtray insert and (1)Phillips screw exposed behind.

3

2

4

5

55

5Unclip and remove the shift lever/ash-tray trim panel.

4

Remove (2) Phillips screws above theradio and (2) Phillips screws below theclimate control panel then remove theradio/climate control assembly.

5

DASH DISASSEMBLY

1996-2000 NISSAN PATHFINDER/QX4 1997-2000

12


Remove (2) Phillips screws from thebase of the radio trim panel.

1

2


Remove (4) Phillips screws securingradio.

4

DASH DISASSEMBLY

2001-2003 NISSAN PATHFINDER

13


Unclip and remove the vent/clockassembly. (Figure A)

1

2

Remove (2) Phillips screws from the topof the radio trim panel then remove thepanel. (Figure B)

3

Remove (4) Phillips screws securingradio. (Figure C)

4

A

B

C

14

KIT ASSEMBLY

2

A

Attach the factory mounting bracketsand the 95-7417 DDIN trimplate/bracket assembly to the DDINhead unit with the screws suppliedwith the unit. (Figure B)

Slide the appropriate bracket intothe trim plate aligning the holes inthe trim plate to the clips on thebracket. (Figure A)

1

B

DOUBLE DIN HEAD UNIT PROVISION

KIT ASSEMBLY

15

2

A

Attach the factory mounting bracketsand the 95-7417 DDIN trimplate/bracket assembly to thestacked ISO DIN head units with thescrews supplied with the units.(Figure B)

Slide the appropriate bracket intothe trim plate aligning the holes inthe trim plate to the clips on thebracket. (Figure A)

1

B

STACKED ISO DIN HEAD UNIT PROVISION

16

FINAL ASSEMBLY

1

MERCURY Villager 1996-98

1

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (4) plastic screws from the base of the storage compartment. Pop out (4) anchor clips (securing the screws) and remove the compartment. Remove (2) Phillips screws from the base of the radio trim bezel. Remove (2) Phillips screws above the radio opening. Remove the ashtray. Pull up and out on the radio trim bezel and remove the bezel. Remove (4) Phillips screws securing the factory radio housing and remove the housing. Disconnect the wiring. Remove (2) Phillips screws securing the factory radio to the housing and remove the radio.

2

"D"

"D"

"D"

"D"

Cut and remove all mounting tabs on Bracket Set #2 EXCEPT tabs "D". (The tabs can be identified by the stamped letter by each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.

2

"D"

"D"

"D"

"D"


Locate the factory wiring harness in the dash. Metra recommends using the proper mating adaptor and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit).

R

MERCURY Villager 1993-95

1

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (1) screw above the climate controls. Unclip the radio trim bezel and remove. Remove (4) Phillips screws securing the factory radio housing and remove the housing. Disconnect the wiring. Remove (8) Phillips screws securing the factory radio to the factory radio housing and remove the radio.

Dtabs down. Slide the aftermarket head unit into the cage until secure (see Fig. A). ISO HEAD UNITS: screws supplied with the unit. Slide the head unit assembly into the Rside clips engage and attach the I

4

17

FINAL ASSEMBLY

2

1

NISSAN 200SX 1995-98

2

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the dummy plate from the center of the switch panel (above the radio opening). Unclip the radio trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. Remove (2) Phillips screws securing the factory cupholder and remove.

1

MERCURY Villager / NISSAN Quest 1999-02

2

Disconnect the negative battery terminal to prevent an accidental short circuit. Open the ashtray/cupholder assembly, depress the retaining clips on each side and remove the assembly. Remove (2) Phillips screws from each side of the ashtray/cupholder assembly. Remove (4) plastic rivets from the lower pocket and slide the pocket back. (NOTE: It is NOT necessary to remove the pocket. Unclip the dash trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.

"A"

Cut Bracket Set #1 along the scored lines removing the SHADED portions of the Brackets. Cut and remove all mounting tabs EXCEPT tabs "A". (The tabs can be identified by the stamped letter by each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.


"A"

"A"

"A"

"A"

"A"

"A"

18

FINAL ASSEMBLY

3

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the climate control trim bezel and remove (2) screws exposed. Unclip the gear shifter trim bezel and remove (2) screws exposed. Remove the ashtray and (1) screw exposed. Unclip the radio trim bezel (the factory head unit, pocket and mounting brackets are secured to the bezel). Disconnect the wiring. Remove the screws securing the mounting brackets to the assembly and remove the brackets.

Cut and remove all mounting tabs on the Radio Housing EXCEPT tabs "B" and "C". (The tabs can be identified by the stamped letter on each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.

NISSAN 240SX 1995-98

1 2

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the gear shifter trim bezel and remove (2) Phillips screws exposed. Remove (2) Phillips screws above the radio opening. Unclip the radio trim bezel. Remove (4) Phillips screws from the factory head unit and disconnect the wiring.

NISSAN Altima 1998-01

1 2

"B"

"B"

"C"

"C"

"B"

"B"

"B"

"B"

Cut Bracket Set #3 along the scored lines removing the SHADED portions of the Brackets. Cut and remove all mounting tabs EXCEPT tabs "B". (The tabs can be identified by the stamped letter by each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.

NISSAN Xterra 2000-01

1

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (2) Phillips screws exposed in the ashtray cavity. Unclip the radio trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.

2

"A"

"A"

Cut Bracket Set #2 along the scored lines removing the SHADED portions of the Brackets. Cut and remove all mounting tabs EXCEPT tabs "A" and "B". (The tabs can be identified by the stamped letter by each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.

"B"

"B"

1

NISSAN Sentra 1995-99

2



"A"

"A"

"A"

"A"

"A"

"A"

19

FINAL ASSEMBLY

4

NISSAN Frontier 1998-01

NISSAN Frontier / Xterra 2002-04

1

1


Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the gear shifter trim bezel and remove. Remove (2) Phillips screws exposed in the shifter cavity. Remove (2) Phillips screws under the climate control cluster. Unclip the radio trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. CAUTION: DO NOT CYCLE THE KEY WHEN REMOVING A DASH WITH PASSENGER AIRBAG ON/OFF SWITCH).

2

2

"A"

"A"

"A"

"A"



"B"

"B"

"B"

"B"

N

20

FINAL ASSEMBLY

5

1

NISSAN Maxima 2000-03

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the vent/radio trim bezel assembly and remove. (NOTE: For Bose systems, the vent assembly will be removed without the bezel). Remove the ashtray insert and (1) Phillips screw exposed. Unclip the gear shifter bezel/ashtray assembly and remove. Remove (2) Phillips screws above the factory head unit and (2) Phillips screws below the climate control panel. Remove the head unit/climate control panel assembly and disconnect the wiring.

1

Illustration not available

Cut and remove all mounting tabs on the Radio Housing. Skip to the Installation Instructions for ALL VEHICLES on Page #9.

2

Using a hammer, flatten the protruding screw holes on the factory mounting brackets. Mount the factory pocket to the brackets with those screws previously removed in step #1 (Fig. A). Cut and remove all mounting tabs on the Radio Housing EXCEPT tabs "A" (Fig. B). The tabs can be indentified by the stamped letter on each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #9.

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the gear shifter trim bezel and remove (2) screws exposed. Remove (1) screw to the left of the ashtray and unclip the ashtray assembly. Unclip the clock/vent assembly and remove. Remove (4) screws from the top of the mounting bracket assembly. Disconnect the wiring and remove the assembly. Remove the screws securing the mounting brackets to to the assembly and remove the brackets.

NISSAN Maxima 1995-99

1 2Fig. A

Fig. B

"A"

"A"

"A"

"A"

21

FINAL ASSEMBLY

6

1

Disconnect the negative battery terminal to prevent an accidental short circuit. Using a screwdriver, pry out on the top of the vent assembly (w/ clock) and remove. Remove (2) Phillips screws from the top of the radio trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.

NISSAN Pathfinder 2001-03

Illustration not available

I

Cut and remove all mounting tabs from Bracket Set #1 EXCEPT tabs "B". (The tabs can be identified by the stamped letter by each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.

2

"B"

"B"

"B"

"B"

NISSAN Pathfinder 1996-00

1

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws from the base of the radio trim bezel. Unclip the bottom edge of the radio trim bezel and disconnect the hazard light, defroster, wiper and cligarette lighter wiring. Remove the radio trim bezel. Remove (4) screws securing the factory head unit and disconnect the wiring.

2

"A"

"A" "C"

"C"

Cut Bracket Set #2 along the scored lines removing the SHADED portions of the Brackets. Cut and remove all mounting tabs EXCEPT tabs "A" and "C". (The tabs can be identified by the stamped letter by each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.

22

FINAL ASSEMBLY

7

NISSAN Quest 1996-98

1

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (4) plastic screws from the base of the storage compartment. Pop out (4) anchor clips (securing the screws) and remove the compartment. Remove (2) Phillips screws from the base of the radio trim bezel. Remove (2) Phillips screws above the radio opening. Remove the ashtray. Pull up and out on the radio trim bezel and remove the bezel. Remove (4) Phillips screws securing the factory radio housing and remove the housing. Disconnect the wiring. Remove (2) Phillips screws securing the factory radio to the housing and remove the radio.

2

"D"

"D"

"D"

"D"


2

"D"

"D"

"D"

"D"


NISSAN Quest 1993-95

1

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (1) screw above the climate controls. Unclip the radio trim bezel and remove. Remove (4) Phillips screws securing the factory radio housing and remove the housing. Disconnect the wiring. Remove (8) Phillips screws securing the factory radio to the factory radio housing and remove the radio.

23

FINAL ASSEMBLY

8

NISSAN Xterra 2000-01

1


2

"A"

"A"


"B"

"B"

1

NISSAN Sentra 1995-99

2



"A"

"A"

"A"

"A"

"A"

"A"

24

FINAL ASSEMBLY

9

ALL VEHICLES

240SX, I-30, MAXIMA: Skip to step #4.ALTIMA, FRONTIER, PATHFINDER, QUEST, VILLAGER, XTERRA: Cut and remove the mounting tabs from the Radio Housing and mount the converted Brackets to the Housing with (4) #8 x Ω" Phillips Flat-head Screws supplied (Fig. A).200SX, SENTRA: Cut and remove the mounting tabs from the Radio Housing. Mount one of the converted Brackets to the Housing with (2) #8 x Ω" Phillips Flat-head Screws supplied and mount one side of the cupholder to the Bracket with (1) factory screw and (1) locating pin. Mount the other Bracket to the Housing with (2) #8 x Ω" Phillips Flat-head Screws supplied and mount the other side of the cupholder with (1) factory screw and (1) locating pin (Fig. B).

3

Using a hammer, flatten the protruding screw holes on the factory mounting brackets. Mount the factory pocket to the brackets with those screws previously removed in step #1 (Fig. A). Cut and remove all mounting tabs on the Radio Housing EXCEPT tabs "A" (Fig. B). The tabs can be indentified by the stamped letter on each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #9.

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the gear shifter trim bezel and remove (2) screws exposed. Remove (1) screw to the left of the ashtray and unclip the ashtray assembly. Unclip the clock/vent assembly and remove. Remove (4) screws from the top of the mounting bracket assembly. Disconnect the wiring and remove the assembly. Remove the screws securing the mounting brackets to to the assembly and remove the brackets.

INFINITI I-30 1996-99

1 2Fig. A

Fig. B

Fig. B

"A"

"A"

"A"

"A"

Fig. A"

25

FINAL ASSEMBLY

101

5 6

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adaptor and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit).

Re-connect the battery terminal and test the unit for proper operation. MAXIMA 1995-99, I-30: Mount the head unit/kit assembly to the trim bezel and factory bracket assembly with factory screws and mount to the sub-dash with factory screws (Fig. A).MAXIMA 2000-02: Mount the head unit/kit assembly to the factory bracket assembly with (4)Phillips Flat-head Screws supplied and mount to the sub-dash with factory screws. 240SX: Mount the head unit/kit assembly to the trim bezel (using tabs "B") with factory screws and then to the sub-dash (using tabs "C") withfactory screws.200SX, ALTIMA, FRONTIER, PATHFINDER, QUEST, SENTRA, VILLAGER, XTERRA: Mount the head unit/kit assembly to the sub-dash with factory screws.

A

B

C

D

A) Strip wire ends back Ω"B) Twist ends togetherC) Solder D) Tape

DIN HEAD UNITS: Slide the DIN cage into the kit and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure (see Fig. A). ISO HEAD UNITS: Secure the ISO Brackets to the sides of the aftermarket head unit with the screws supplied with the unit. Slide the head unit assembly into the Radio Housing until the side clips engage and attach the ISO Trimring over the mounted head unit (see Fig. B).

Fig. A

Fig. A

Fig. B

PATENT PENDING

PATENT PENDING

4

FINAL ASSEMBLY

1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to preventelectrical short circuit.)

2 Re-connect the negative battery terminal and test the unit for proper operation.3 Reassemble radio and dash assemblies in reverse order of disassembly.

A

A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

B

C

D

Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.

12V Ignition / Acc . . . Red

12V Batt / Memory . . Yellow

Ground . . . . . . . . . . . Black*

Power Antenna . . . . . Blue

Amp Turn-On . . . . . . Blue / White

Amp Ground . . . . . . . Black / White

Illumination. . . . . . . . Orange

Dimmer . . . . . . . . . . Orange / White

Right Front (+) . . . . . Gray

Right Front (-) . . . . . . Gray / Black

Left Front (+) . . . . . . White

Left Front (-) . . . . . . . White / Black

Right Rear (+). . . . . . Violet

Right Rear (-) . . . . . . Violet / Black

Left Rear (+). . . . . . . Green

Left Rear (-) . . . . . . . Green / Black

*NOTE: When Black a wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.

METRA / EIA WIRING CODE

FINAL WIRING CONNECTIONS

26

cf-710ni / ibr-710ni - metra online · 2015-07-16 · 1 disconnect the negative battery terminal to...

Documents