chapter 6: mosfet & related devices chapter 6: mosfet & related devices part 2
TRANSCRIPT
CHAPTER 6: MOSFET CHAPTER 6: MOSFET & RELATED DEVICES& RELATED DEVICES
Part 2
MOSFET
MOSFET
MOSFET FUNDAMENTALS
Perspective view of a metal-oxide-semiconductor field-effect transistor (MOSFET).
IGFET : insulating-gate field-effect transistor
MISFET : Metal-insulator-semiconductor field-effect transistor
MOST : Metal-oxide-semiconductor transistor
Basic device parameters:
• Channel length, L, (distance between two metallurgical n+ -p junction)
•Channel width, Z
•Oxide thickness, d
•Junction depth, rj
•Substrate doping, NA
BASIC OPERATION
2) Low Drain Voltage :When a small drain voltage applied, electrons will flow from the source to the drain through the conducting channel. The channel acts as a resistor, and the drain current ID
proportional to the drain voltage. Current flow can be controlled by using gate voltage. This create a linear region in IV curve
1) When VG=0 :Source and drain electrodes correspond to two p-n junctions connected back to back. Zero current flow from source to drain ideally. This create an inversion layer which will be a threshold voltage, Vt prior current flow. When small positive voltage applied to gate, VG the central MOS structure is inverted and a channel is formed. Current begin to flow.
3) Onset On Saturation :If VD increases, the inversion layer width reduces as the VD is larger than VG. At one point, the inversion layer will disappear as the VD is enough to compensate the inversion layer strength. This point is called pinch off point and the VD saturates.
4) Beyond saturation :Beyond pinch off point, maximum number of electron will flow from source to drain. Therefore, the current saturation occur. The current flow now controlled by VG and independent of VD. The major changes is the reduction of channel length.
Derivation of basic characteristics under following conditions:
a) The gate structure correspond to an ideal MOS diode – no interface traps, fixed-oxide charges or work function differences.
b) Only drift current considered
c) Carrier mobility in the inversion layer is constant
d) Doping in the channel is uniform
e) Reverse leakage current is negligibly small
f) The transverse field created by the gate voltage in the channel is much larger than the longitudinal field created by the drain voltage
g) The gradual-channel approximation – the charges contained in the surface depletion region of the substrate are induced solely from the field created by gate voltage
Figure 6.16. (a) MOSFET operated in the linear region. (b) Enlarged view of the channel. (c) Drain voltage drop along the channel.
oSGS CyVyQ )()(
QS : Total charge induced in the semiconductor per unit area
y : distance from the source
S(y) : surface potential at y
Co=ox/d : gate capacitance per unit area
)()()()()(
yQCyVyQyQyQ
scosG
scsn
Qn : charge in the inversion layer per unit area
Qs: total of Qn
Qsc : charge in surface depletion region per unit area
we can obtain Qn
)(2)( yVy Bs Refer fig. 16.6(c)
)(22)( yVqNWqNyQ BAsmAsc
Conductivity of the channel at y: )()()( xxqnx n
ii xx n dxxqnL
ZdxxLZg
00)()(
)(yQZdy
gLdydR
nn
)(yQZdyIdRIdV
nn
DD
Channel conductance (constant mobility) :
nn Q
LZg
Channel resistance of an elemental section by:
Voltage drop across the elemental section:
ID independent of y
Figure 6.17. Idealized drain characteristics of a MOSFET. For VD VDsat,
the drain current remains constant.
2/32/3 22
232
22 BBD
o
AsD
DBGonD V
CqN
VVVCLZI
For a given VG : ID increases linearly with VD then saturated
The dashed line : locus of the drain voltage VDsat (ID approach a max value)
2
2 TGon
Dsat VVLCZI
2
2 2112
GBGDsat
VVV
TGonD VVCLZI TGD VVV
B
o
BAsT C
qNV
2
22
TGonVD
DD VVC
LZ
VIg
G
constant
DonVG
Dm VC
LZ
VIg
D
constant
Consider linear and saturation regions (for small VD)
for
Threshold voltage VT :
Channel conductance gD :
Transconductance gm :
Pinch-off point : VD increased to a point that charge Qn(y) in the inversion layer at y=L number of mobile ē at the drain are reduced drastically
At this point VD & ID VDsat & IDsat
VD > VDsat saturation region
2
2 TGon
Dsat VVLCZI
2
2 2112
GBGDsat
VVV
TYPES OF MOSFETCross section, output, and transfer characteristics of four types of MOSFETs.
TRESHOLD VOLTAGE
Figure 6.20. Calculated threshold voltage of n-channel (VTn) and p-channel (VTp) MOSFETs as a function of impurity concentration, for devices with n+-, p+–polysilicon, and mid-gap work function gates assuming zero fixed charge. The thickness of the gate oxide is 5 nm. NMOS, n-channel MOSFET; PMOS, p-channel MOSFET.
MOSFET applied in the semiconductor industry for :a) VLSI Circuitsb) Memory Devices ( DRAM, SRAM, Nonvolatile Memory)c) CMOS Digital Circuitd) Microprocessors
Advantages of MOSFET :a) In CMOS, perfect zero current when input switch off. Good logic ‘1’ and logic ‘0’ condition.b) Ability to scale down in size. (Channel length, width, area)c) Ability to control threshold voltage when device shrink. Quick switching.d) Oxide layer between gate and channel prevent DC flow – Power Consumption.e) Low power consumption allow more components per chip surface area.
MOSFET APPLICATION
DISADVANTAGES OF MOSFET
Reduces VT makes MOSFET could not switched off – weak inversion layer.
Interconnect capacitance between wires – device miniature reduces.
Heat production impact – shrink device size, increasing device quantity.
Thin oxide requirement – gate oxide tunneling leakage problem.
Increased process fabrication steps – complex circuit design.