charger fitting
TRANSCRIPT
-
8/3/2019 Charger Fitting
1/28
1
Step to Lexus IS200 Compressor1.
- Luftfiltersystem sowie Generatorabdeckung
demontieren
- remove airfilter system and alternator cover
- Obere Motorabdeckung zurModifikation entfernen
- remove top engine cover for modification
- Motorabdeckung vom Serienstand
(A) zu (B) modifizieren
- modify engine cover from std. (A)to (B)A
B
-
8/3/2019 Charger Fitting
2/28
2
Step to Lexus IS200 Compressor2.
- Hitzeschild zwecks Modifikationentfernen
- remove heatshield for modifikation
- Hitzeschild wie links im Bild gezeigt
modifizierenA = mu ausgeschnitten werdenB = mit Karosseriehammer bearbeiten( im Bild rechts ist das Serienteil zusehen )
- modify heatshield as shown left A = must be cut out B = must be deformed with chassis
hammer ( std. part is shown right )
B
A
-
8/3/2019 Charger Fitting
3/28
3
Step to Lexus IS200 Compressor3.
- Nur fr links gesteuerte Fahrzeuge !!!
- left hand drive cars only !!!
-
8/3/2019 Charger Fitting
4/28
4
Step to Lexus IS200 Compressor4.
- Halter A durch Halter B ersetzen- Schlauch C nach unten drehen um mehr Raum fr den Compressor
Halter zu schaffen
- replace bracket A by bracket B- turn down hose to create more space for the compressor main bracket
A
B
C
-
8/3/2019 Charger Fitting
5/28
5
Step to Lexus IS200 Compressor5.
- (A) Befestigung an Motorhalter rechts
- (A) to be fixed on right hand engine mount
A
-
8/3/2019 Charger Fitting
6/28
6
Step to Lexus IS200 Compressor6.
- Halter ( Teil 11) + Absttzung ( Teil 9 ) gemeinsam mit modifiziertemHitzeblech montieren
- Kabelstrang durch den Halter ziehen und wieder endgltig anschlieen- Kabelstrang sicher vor Beschdigung mit Kabelbindern verlegen
- install main bracket ( Part 11 ) + stay ( Part 9 ) together with modified heatshield
- put wireing loom trough main bracket and install finally- please fix wireing loom proper to avoid damage
M8 x 40
-
8/3/2019 Charger Fitting
7/28
7
Step to Lexus IS200 Compressor7.
- Halterabsttzung ( Teil 24 ) zwischen Zylinderkopf und Compressorhaltermontieren
- fit support (Part 24) between cylinderhead and compressor bracket
-
8/3/2019 Charger Fitting
8/28
8
Step to Lexus IS200 Compressor8.
- Bild zeigt korrekte Einbaulage des Kabels (nur RHD)
- picture shows proper cable fixation ( only RHD )
-
8/3/2019 Charger Fitting
9/28
9
Step to Lexus IS200 Compressor9.
- Bild zeigt korrekte Einbaulage des Kabels
- picture shows proper cable fixation
-
8/3/2019 Charger Fitting
10/28
10
Step to Lexus IS200 Compressor10.
- Bild zeigt neue Einbaulage des Massekabels (nur RHD )
- picture shows new ground - cable position (RHD only)
-
8/3/2019 Charger Fitting
11/28
11
Step to Lexus IS200 Compressor11.
- In diesem Bereich die markierten Stege abschneiden um Platz fr dieLuftfhrungsrohre zu schaffen
- Cut away marked fan supports as shown on drawing to make space for thecompressor tubing system
-
8/3/2019 Charger Fitting
12/28
12
Step to Lexus IS200 Compressor12.
- Abdeckung entfernen
- remove cover
-
8/3/2019 Charger Fitting
13/28
13
Step to Lexus IS200 Compressor13.
- Riemenscheibe montieren
- install main pulley
-
8/3/2019 Charger Fitting
14/28
14
Step to Lexus IS200 Compressor14.
- Spannrolle montieren
- install tensioner
-
8/3/2019 Charger Fitting
15/28
15
Step to Lexus IS200 Compressor15.
- Compressor wie im Bild gezeigt vorbereiten
- assemble compressor unit as shown in picture
-
8/3/2019 Charger Fitting
16/28
-
8/3/2019 Charger Fitting
17/28
17
Step to Lexus IS200 Compressor17.
- Compressor Einheit auf dem Halter montieren- Antriebsriemen wie im Bild gezeigt auflegen- Antriebsriemen spannen
- install compressor assembly onto main bracket - put on belt as shown above - tighten the belt
-
8/3/2019 Charger Fitting
18/28
18
Step to Lexus IS200 Compressor18.
- Befestigungsschrauben des Drosselklappenteils entfernen / Stehbolzenausdrehen
- remove standard fixation bolts of the throttle body and take out thestudbolts
-
8/3/2019 Charger Fitting
19/28
19
Step to Lexus IS200 Compressor19.
- Rohradapter ( Teil 7) auf das Drosselklappenteil aufstecken und mitSchrauben M8 x 120mm befestigen
- put tube adapter ( Part 7) on throttle body and fix with M8 x 120mm Inhexbolts
-
8/3/2019 Charger Fitting
20/28
20
Step to Lexus IS200 Compressor20.
- Bettigungsmechanismu fr die Bypass Klappe wie im Bild gezeigtinstallieren
- install bypass linkage as shown in picture
-
8/3/2019 Charger Fitting
21/28
21
Step to Lexus IS200 Compressor21.
- Motorentlftungsschlauchentfernen
- remove engine breather hose
- Motorabdeckung montieren- Schwingelement einschrauben
- fix top engine cover again- fit silent block
- Luftfilterhalter wie im Bildgezeigt befestigen
- Schwingelemt desSerienluftfilterkastenbernehmen
- fit airfilterbracket as shownin picture
- carry over rubber bush fromstd. airfilterbox
-
8/3/2019 Charger Fitting
22/28
22
Step to Lexus IS200 Compressor22.
- (A) Luftfiltergehuse wie im Bild gezeigt montieren- (B) Luftfiltereinsatz wie im Bild gezeigt montieren- (C) Ansauglufttemperaturfhler mit Seriengummi einsetzen- (D) Schlauch aufstecken und mit Schlauchschelle befestigen
- (A) fit airfilterbox as shown in picture- (B) fit airfilter insert as shown in picture- (C) fit intake air temperatur sensor with std. rubber fixation- (D) put on hose and fx with hose clip
A B
C
D
-
8/3/2019 Charger Fitting
23/28
23
Step to Lexus IS200 Compressor23.
- Khlschleifenposition wie imBild gezeigt verndern umPlatz fr denIntercooler zu schaffen
- change the position of thecooling tube in order to getspace for the intercooler
- Obere Luftfhrung krzen( nur Automatik FZ )
- cut top airduct on cars with automaticgearbox
-
8/3/2019 Charger Fitting
24/28
24
- Luftfhrungsrohre (Teil 13 + 14 + 15) mitSchluchen und Intercooler im Fahrzeuglose zusammenstecken
- Die beste Montageposition ermitteln- Bohrposition Markieren
- !!!! AUF AUSREICHENDEFREIGNGIGKEIT ZU ANDERENKOMPONENTEN ACHTEN UND DIESESICHERSTELLEN !!!!
- Intercooler wieder entfernen undBefestigungslcher bohren
- Befestigungslcher gegen Rost schtzen
- put airtubes (Part 13 +14 +15) , all hosesand intercooler looseinto the car in order to find the best
position- Mark the drilling position- !!! Make sure to have enough clearance to
all chassis parts and to other components !!!- remove Intercooler unit and drill fixation
holes- protect holes against rust
Step to Lexus IS200 Compressor24.
Rechte und linke Radhausverkleidungausschneiden wie im Bild gezeigt !
Cut out RH + LH wheel house cover as shown inpicture below !
-
8/3/2019 Charger Fitting
25/28
25
Step to Lexus IS200 Compressor25.
- Intercooler mit Schluchen +Rohren endgltig montieren,dabei auf festen Sitz allerKomponenten achten
- Intercooler mit Gummi-elementen befestigen
- Nochmals sicherstellen, da
sich Komponenten nichtberhren und nicht an derKarosserie anliegen, da essonst zur Geruschbildungkommen kann !!!
- Stosstangenabdeckung wiedermontieren
- Finally fix the Intercooler andall tubes and hoses
- Fix intercooler with rubbermounts
- Make sure that all componentsare proper fixed
- Make sure as well that nocomponents are touching thechassisin order to avoid noises
- put on frontbumper coveragain
-
8/3/2019 Charger Fitting
26/28
26
Steps to Lexus IS200 Compressor26.
- untere Motorabdeckung entlang der Markierung abschneiden
- cut lower engine cover along the marked line
-
8/3/2019 Charger Fitting
27/28
27
Step to Lexus IS200 Compressor27.
- untere Motorabdeckung montieren
- reinstall lower engine cover
-
8/3/2019 Charger Fitting
28/28
Step to Lexus IS200 Compressor28.
- Luftfilterdeckel montieren, dabei die Schrauben mit etwas Silicon gegenLsen sichern
- Alle anderen Standard Komponenten wieder montieren
- finally fit airfilter box-cover, fix the bolts with some silicon to keep themtight
- re-install all other standard components