CHART

PERUVIAN TECHNICAL STANDARDS

Peruvian Technical Standards

Elaborated by the Normative Technical Committee Rational Use of Energy and the Energy Efficiency - INDECOPI (December 2007)

Sub-Committee Item Standard Name Objective Date of approval

01 NTP IEC 60034-2:2001 Rotation Electrical Motors. Test Methods

Establishes methods to determine the efficiency from the tests, and also specifies the methods to obtain the losses of a certain nature when these are required for other purposes.

Oct.14 .2001

02 NTP IEC 60034-2/A2 Addenda 2

Rotation Electrical Motors. Test Methods (Part 2)

Introduces the following modifications to the Standard NTPIEC 60034-2/ 2001, according to the corresponding standard IEC 34-2/A2:199.

Oct.13.2002Electric Motors

03 NTP 399.450.2003 Energy Efficiency squirrel cage motors. Limits and Labeling.

Establishes the minimum efficiency values and the labeling specification which should be complied with by electric motors to which this Standard refers

Aug.30.2003.

04 NTP 350.300.2002 Industrial Boilers. Procedure for energy efficiency determination.

Establishes the test method to be applied to verify the thermal efficiency of the package type boilers with smoke pipes and water pipes without heat recovery equipment at the moment of their reception. All boilers which are within the field of application of this Standard should be tested.

Dec.15.2002

05 NTP 350.301.2004 Industrial Boilers. Minimum Levels of thermal efficiency

Establishes the thermal efficiency standards which should be complied with by new industrial boilers without heat recovery equipment.

Aug.4.2004

06 NTP ISO 7371:2002

Refrigerators with or without food compartments with low temperature. Characteristic and test methods.

Establishes essential characteristics of the domestic refrigerators, with or without storage or low temperature compartments which are completely assembled in factory, and proposes test methods for checking these characteristics.

Jun.10.2002

07 NTP ISO 8561:2003

Appliances for storage of frozen food and food freezers. Characteristics and test methods

Specifies the essential characteristics for domestic appliances for storage of frozen food and freezers for food cooled by internal forced air circulation and for refrigerators-freezers with or without frozen food storage compartments or hold, cooled by internal forced air circulation, which are completely assembled in factory and dictates the test methods for checking these characteristics.

Apr.5.2003

Industrial Boilers Refrigeration

08 NTP 399.483 2007

Energy Efficiency in Refrigerating appliances , Refrigerators– Freezers and for Domestic Use

Establish the energy consumption of reference CER and the ranks of energy consumption which will permit to classify food refrigerators, refrigerators-freezers and freezers according to their energy behavior, specifying the contents of the label of energy consumption for all the types of domestic refrigeration appliances operated with hermetic motor compressor when they are tested and classified according to what is established in Chapter 15 of standard NTP-ISO 8561 and standard NTP –ISO 7371.

Mar.15.2007

Sub-Committee Item Standard Name Objective Date of approval

09 NTP 399.400.2001 Solar collectors. Test methods to determine efficiency

Establishes the test methods to determine the thermal behavior of solar energy collectors which uses one single phase and do not have significant energy interior feed.

Nov.3.2001

10 NTP 399.403.2006

Photovoltaic Systems of up to 500 Wp. Technical specifications and method for energy qualification.

Establishes a set of technical requirements for the components of the photovoltaic system, such s the photovoltaic modules, the batteries, load controllers, fluorescent lamps and the integrated photovoltaic system. Likewise, is established a procedure to obtain the energy capacity of a photovoltaic system.

Feb.4.2006

11 NTP 399.404.2006 Solar Energy Water Heating Systems. Bases for their efficient dimensioning.

Establishes the main principles for designing a solar heating system for drainage waters, with collectors with plane plates without inside energy storage and storage deposit

Oct.13.2006

12 NTP 399.482 2007 Solar Energy Water Heating Systems. Procedure for their efficient installation.

Establishes the procedures and precise techniques to install a Water Heating System with Solar Energy, considering the conditions and general characteristics of the destination physical space.

Feb.7.2007

Solar Systems

13 NTP 399.405 2007

Solar Energy Water Heating. Definition and annual forecast for their yield with outdoors tests.

Establishes the test procedures which will permit to define the yield of the Solar Energy Water Heating (Sistemas de Calentamiento de Agua con Energía Solar (SCAES)) under direct exposure to solar radiation (out of doors tests), without auxiliary reinforcement for heating, to forecast annual yield of the system for a period of twelve (12) hours of daily heating.

Jun-20.2007

14 NTP 370.100.2000 Compact Fluorescent Lamps Definitions, requirements and labeling.

Establishes the minimum energy efficiency specifications which Compact Fluorescent Lamps should have in Peru, so they can have official certification. Likewise, sets the technical parameters, both electronic and luminous, the values of which should be complied with by the Compact Fluorescent Lamps.

Oct.24.2001

15 NTP 370.101.2003 Labeling of energy efficiency for domestic use lamps.

Establishes the specifications which should be complied with by the design of the energy efficiency label for domestic use lamps. Also specifies the classes of energy efficiency that a lamp has.

Jan.25.2003.

16 NTP IEC 60921.2005 Ballasts for tubular fluorescent lamps. Requirement for functioning

Specifies the requirements of the behavior of the ballasts excluding those of the resistance type for use with supplies of alternate current up to 1000 V, at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with preheated cathodes with or without starter or starting device with nominal power, dimensions and characteristics specified in standards IEC 60081 and 60901. This standard is applied to complete ballasts and its component parts such as resistors, transformers and condensers.

Dec.9.2005

Lighting

17 NTP IEC 61347-1.2006 Control devices for lamps. Part 1: General requirement and safety features.

Specified the general requirements and requisites for safety in control devices of lamps destined to be used with continuous current feed up to 250 V and/or with alternate current feed of up to 1 000 V at 50 Hz or 60 Hz.

Mar.20.2006

Sub-Committee Item Standard Name Objective Date of approval

18 NTP IEC 61347-2-8.2006

Control devices per lamps. Part 2-8: Particular requirements for ballasts in fluorescent lamps.

Specifies particular requisites for safety in ballasts other than those of the resistor type, to be used with alternate current up to 1 000 V of frequency equal to 50 Hz or 60 Hz, associated to fluorescent lamps with or without preheated cathodes which operate with or without feeder or starter device and the nominal power of which, dimensions and characteristics are indicated in Standard IEC 60081 and in Standard IEC 60901.

May 27.2006

19 NTP IEC 61347-2-9.2006

Control devices for lamp. Part 2-9. Particular requirements for discharge lamps ballasts (except fluorescent lamps).

Specifies the particular safety requirements for ballasts of discharge lamps such as mercury vapor lamps at high pressure, sodium vapor lamps at low pressure, sodium vapor lamps at high pressure and halogen metallic lamps

Jul.7.2006

20 NTP IEC 60923.2006

Auxiliary equipment for discharge lamps ballasts (excluding the tubular fluorescent lamps). Requirements for operation.

Specifies the requirements of operation of ballasts for discharge lamps such as mercury vapor at high pressure, sodium vapor lamps at low pressure, sodium vapor lamps at high pressure and halogen metallic lamps

Aug.6.2006

21 NTP IEC 50294.2006 Method for measuring total inlet power of the circuits of lamps ballasts.

Gives the total inlet power measuring method of the ballast-lamps circuits when they operate with their associated fluorescent lamp(s). This standard is applied to electric ballast-lamp circuits including only the ballast and the lamp(s).

Dec.3.2006

22 NTP IEC 61347-2-3.2007

Devices for lamp control. Part 2-3. Particular requirements for electronic ballasts fed with alternate current for fluorescent lamps.

Specifies the particular safety requirements applicable to electronic ballasts for the use with alternate current up to 1 000 V at 50 Hz or 60 Hz with operation frequencies other than those of the feeding network, associated with the fluorescent lamps specified in Standard IEC 60081 and Standard IEC 60901,and to other fluorescent lamps which operate at high frequency.

Jan.31.2007

23 NTP IEC 60598-2-22 2007

Luminaries. Part 2-22. Particular requirements. Luminaries for emergency.

Specifies the requirements applicable to the luminaries for emergency lighting destined to be used with sources of electric light for emergency feeding voltages which will not overpass 1 000 V.

Mar.15.2007

24 NTP IEC 60929.2007

Electronic ballasts fed with alternate current for tubular fluorescent lamps. Requirements for operation.

Specifies the requisites of operation for electronic ballasts fed with alternate current of up to 1 000 V, at 50 Hz or 60 Hz, with working frequencies which are not those of the feeder frequency and used in association with tubular fluorescent lamps as indicated in Standards IEC 60081 and IEC 60901, and with other types of fluorescent lamps for the operation at high frequency.

Nov.15..2007

25 NTP IEC 60379.2006

Methods to measure efficiency of accumulation electric water heaters for domestic use

Establish and define the main characteristics for the operation of the electric accumulation water heaters which are of the user’s interest and describe the standardized methods for measuring these characteristics.

Feb.4.2006

Water Heaters

26 NTP 370.500 2007

Gas appliances, Normal gases for tests Terminology, Classification and Specifications.

Establishes the test gases, the test pressures and the categories of the appliances, relative to the use of gaseous fuels of the first, second and third families.

Jan.22.2007

Peruvian Technical Standards in process of approval by INDECOPI (December – 2007)

Sub-

Committee Item Standard Name Date

Submission to n

INDECOPI

Refrigeration 01 Will be designated by INDECOPI

Domestic Refrigeration Appliances, Appliances for frozen food storage and freezers. Characteristics and test methods. Sept.5.2007

Lighting 02 Will be designated by INDECOPI Starters to put on fluorescent lamps Nov.29.2007

Lighting 03 Will be designated by INDECOPI

Lamp control devices. Part 2-1: Particular requisites for starters (except fluorescent lamp starters) Nov.29.2007

Lighting 04 Will be designated by INDECOPI

Auxiliaries for lamps. Condensers for use in the tubular fluorescent lamps and other discharge lamps circuits. General and safety requirements

Nov.29.2007

Lighting 05 Will be designated by INDECOPI

Condensers to use in tubular fluorescent lamps and discharge lamps. Requirements of operation. Nov.29.2007

Lighting 06 Will be designated by INDECOPI

Lamp control devices. Fluorescent lamps ballasts. Energy Codification System. Dec.11.2007.